ubi attach failure

ubi attach failure

[twebb]

I get the error shown below when attempting to attach to an mtd device
on a Marvell PXA-based platform.  The flash is MLC NAND from Samsung
K9LBG08U0D (4G x 8-bit).

I don't know if it's related, but one thing that stands out is that I
only see the error on two platforms whose bad block table has >28
entries (other tested boards have approx. 2-8 bad blocks).

Any suggestion as to what would cause error and whether it may be
related to the high number of bad blocks?


[root@ESIedge mtd-utils]#
[root@ESIedge mtd-utils]# ./ubiattach /dev/ubi_ctrl -m5
[   34.925463] UBI: attaching mtd5 to ubi0
[   34.929305] UBI: physical eraseblock size:   524288 bytes (512 KiB)
[   34.936410] UBI: logical eraseblock size:    516096 bytes
[   34.941882] UBI: smallest flash I/O unit:    4096
[   34.946583] UBI: VID header offset:          4096 (aligned 4096)
[   34.952648] UBI: data offset:                8192
[   45.897062] UBI error: compare_lebs: unsupported on-flash UBI format
[   45.897076]
ubiattach: error!: cannot attach mtd5
           error 22 (Invalid argument)
[root@ESIedge mtd-utils]#


I use the following steps to create the UBI image to put onto /dev/mtd5:

1.  mkfs.ubifs -m 4KiB -e 516096 -c 715 -o sys_ubifs.img -d sys_fs
2.  mkfs.ubifs -m 4KiB -e 516096 -c 715 -o data_ubifs.img -d sys_fs
3.  mkfs.ubifs -m 4KiB -e 516096 -c 715 -o data2_ubifs.img -d sys_fs
4.  mkfs.ubifs -m 4KiB -e 516096 -c 5838 -o storage_ubifs.img -d sys_fs
5.  ubinize -o system_ubi.img -m 4KiB -p 512KiB -s 4KiB system.cfg

system.cfg:

[sys-volume]
mode=ubi
image=sys_ubifs.img
vol_id=0
vol_size=351MiB
vol_type=dynamic
vol_name=system

[data-volume]
mode=ubi
image=data_ubifs.img
vol_id=1
vol_size=351MiB
vol_type=dynamic
vol_name=data

[data2-volume]
mode=ubi
image=data2_ubifs.img
vol_id=2
vol_size=351MiB
vol_type=dynamic
vol_name=data2

[storage-volume]
mode=ubi
image=storage_ubifs.img
vol_id=3
vol_size=2871MiB
vol_type=dynamic
vol_name=storage

The mtd partition is defined by...
{
    .name        = "System",
    .offset      = 0x04000000,
    .size         = 0xfc000000,
}

Re: ubi attach failure

[Artem Bityutskiy]

On Tue, 2010-01-05 at 18:16 -0500, twebb wrote:
> I get the error shown below when attempting to attach to an mtd device
> on a Marvell PXA-based platform.  The flash is MLC NAND from Samsung
> K9LBG08U0D (4G x 8-bit).
> 
> I don't know if it's related, but one thing that stands out is that I
> only see the error on two platforms whose bad block table has >28
> entries (other tested boards have approx. 2-8 bad blocks).
> 
> Any suggestion as to what would cause error and whether it may be
> related to the high number of bad blocks?

What did you use to flash your image? It looks like it was not flashed
properly.

-- 
Best Regards,
Artem Bityutskiy (Артём Битюцкий)