* [PATCH RFC -next] omap: fix omap2plus_defconfig build
From: Anand Gadiyar @ 2010-12-03 18:31 UTC (permalink / raw)
To: linux-arm-kernel, linux-omap, linux-next; +Cc: Anand Gadiyar
Having CONFIG_SWP_EMULATE causes the build of omap2plus_defconfig
to fail as below:
CC arch/arm/kernel/swp_emulate.o
/tmp/ccCx8SX8.s: Assembler messages:
/tmp/ccCx8SX8.s:339: Error: selected processor does not support ARM mode `ldrexb r7,[r6]'
/tmp/ccCx8SX8.s:340: Error: selected processor does not support ARM mode `strexb r3,r2,[r6]'
make[1]: *** [arch/arm/kernel/swp_emulate.o] Error 1
make: *** [arch/arm/kernel] Error 2
While a proper fix is being found, work around it by turning off
the config option in the defconfig.
While at it, make savedefconfig trimmed a few lines.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
---
1. The issue has been discussed here:
http://marc.info/?t=128748412500003&r=1&w=2
It's been around for a couple of months now.
The last status was that maybe the toolchain should be fixed.
I'm afraid I don't know how to fix this properly, so I'm
hoping we can live with a workaround like this...
2. An alternative patch is this one:
http://marc.info/?l=linux-arm-kernel&m=128748874510144&w=2
3. Not sure if this should have been combined with the other noise
from make savedefconfig - maybe I should have hand-edited the
old defconfig to add one line.
arch/arm/configs/omap2plus_defconfig | 68 ++++-------------------------------
1 file changed, 8 insertions(+), 60 deletions(-)
Index: mainline/arch/arm/configs/omap2plus_defconfig
===================================================================
--- mainline.orig/arch/arm/configs/omap2plus_defconfig
+++ mainline/arch/arm/configs/omap2plus_defconfig
@@ -21,57 +21,23 @@ CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_OMAP=y
-CONFIG_ARCH_OMAP2=y
-CONFIG_ARCH_OMAP3=y
-CONFIG_ARCH_OMAP4=y
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_OMAP_MUX_DEBUG=y
-CONFIG_OMAP_32K_TIMER=y
-CONFIG_MACH_OMAP_GENERIC=y
-CONFIG_ARCH_OMAP2420=y
-CONFIG_ARCH_OMAP2430=y
-CONFIG_ARCH_OMAP3430=y
-CONFIG_MACH_OMAP_H4=y
-CONFIG_MACH_OMAP_APOLLON=y
-CONFIG_MACH_OMAP_2430SDP=y
-CONFIG_MACH_OMAP3_BEAGLE=y
-CONFIG_MACH_DEVKIT8000=y
-CONFIG_MACH_OMAP_LDP=y
-CONFIG_MACH_OVERO=y
-CONFIG_MACH_OMAP3EVM=y
-CONFIG_MACH_OMAP3517EVM=y
-CONFIG_MACH_OMAP3_PANDORA=y
-CONFIG_MACH_OMAP3_TOUCHBOOK=y
-CONFIG_MACH_OMAP_3430SDP=y
-CONFIG_MACH_NOKIA_N8X0=y
-CONFIG_MACH_NOKIA_RX51=y
-CONFIG_MACH_OMAP_ZOOM2=y
-CONFIG_MACH_OMAP_ZOOM3=y
-CONFIG_MACH_CM_T35=y
-CONFIG_MACH_IGEP0020=y
-CONFIG_MACH_SBC3530=y
-CONFIG_MACH_OMAP_3630SDP=y
-CONFIG_MACH_OMAP_4430SDP=y
CONFIG_ARM_THUMBEE=y
-CONFIG_ARM_L1_CACHE_SHIFT=5
+# CONFIG_SWP_EMULATE is not set
CONFIG_ARM_ERRATA_411920=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_SMP=y
# CONFIG_LOCAL_TIMERS is not set
-CONFIG_AEABI=y
CONFIG_LEDS=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="root=/dev/mmcblk0p2 rootwait console=ttyO2,115200"
CONFIG_KEXEC=y
CONFIG_FPE_NWFPE=y
-CONFIG_VFP=y
-CONFIG_NEON=y
CONFIG_BINFMT_MISC=y
-CONFIG_PM=y
CONFIG_PM_DEBUG=y
-CONFIG_PM_RUNTIME=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
@@ -90,7 +56,7 @@ CONFIG_NETFILTER=y
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
-CONFIG_BT_RFCOMM=y
+CONFIG_BT_RFCOMM=m
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
@@ -126,7 +92,6 @@ CONFIG_MTD_UBI=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=16384
-CONFIG_EEPROM_LEGACY=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SCSI_MULTI_LUN=y
@@ -157,8 +122,6 @@ CONFIG_TOUCHSCREEN_ADS7846=y
CONFIG_INPUT_MISC=y
CONFIG_INPUT_TWL4030_PWRBUTTON=y
CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_8250_NR_UARTS=32
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
@@ -167,9 +130,7 @@ CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_OMAP=y
CONFIG_SPI=y
CONFIG_SPI_OMAP24XX=y
CONFIG_DEBUG_GPIO=y
@@ -180,10 +141,6 @@ CONFIG_POWER_SUPPLY=y
CONFIG_WATCHDOG=y
CONFIG_OMAP_WATCHDOG=y
CONFIG_TWL4030_WATCHDOG=y
-CONFIG_MENELAUS=y
-CONFIG_TWL4030_CORE=y
-CONFIG_TWL4030_POWER=y
-CONFIG_REGULATOR=y
CONFIG_REGULATOR_TWL4030=y
CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
@@ -196,7 +153,6 @@ CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_PLATFORM=y
CONFIG_DISPLAY_SUPPORT=y
-# CONFIG_VGA_CONSOLE is not set
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
CONFIG_FONTS=y
@@ -205,25 +161,20 @@ CONFIG_FONT_8x16=y
CONFIG_LOGO=y
CONFIG_SOUND=m
CONFIG_SND=m
-CONFIG_SND_MIXER_OSS=y
-CONFIG_SND_PCM_OSS=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
CONFIG_SND_VERBOSE_PRINTK=y
CONFIG_SND_DEBUG=y
-CONFIG_SND_USB_AUDIO=y
-CONFIG_SND_SOC=y
-CONFIG_SND_OMAP_SOC=y
-CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=y
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_SOC=m
+CONFIG_SND_OMAP_SOC=m
+CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=m
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_SUSPEND=y
-# CONFIG_USB_OTG_WHITELIST is not set
CONFIG_USB_MON=y
-# CONFIG_USB_MUSB_HDRC is not set
-# CONFIG_USB_MUSB_OTG is not set
-# CONFIG_USB_GADGET_MUSB_HDRC is not set
-CONFIG_USB_MUSB_DEBUG=y
CONFIG_USB_WDM=y
CONFIG_USB_STORAGE=y
CONFIG_USB_LIBUSUAL=y
@@ -249,7 +200,6 @@ CONFIG_RTC_DRV_TWL4030=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
-CONFIG_INOTIFY=y
CONFIG_QUOTA=y
CONFIG_QFMT_V2=y
CONFIG_MSDOS_FS=y
@@ -273,12 +223,10 @@ CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_PROVE_LOCKING=y
-# CONFIG_LOCK_STAT is not set
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_BUGVERBOSE is not set
CONFIG_DEBUG_INFO=y
^ permalink raw reply
* Re: linux-next: Tree for December 3 (cifs)
From: Randy Dunlap @ 2010-12-03 17:48 UTC (permalink / raw)
To: Stephen Rothwell, Steve French; +Cc: linux-next, LKML, linux-cifs
In-Reply-To: <20101203130440.9f89dd31.sfr@canb.auug.org.au>
On Fri, 3 Dec 2010 13:04:40 +1100 Stephen Rothwell wrote:
> Hi all,
>
> Changes since 20101202:
When CIFS_EXPERIMENTAL is not enabled:
(.text+0xdf6c9): undefined reference to `get_cifs_acl'
from fs/cifs/xattr.c:cifs_getxattr()
CONFIG_CIFS=y
# CONFIG_CIFS_STATS is not set
CONFIG_CIFS_WEAK_PW_HASH=y
# CONFIG_CIFS_UPCALL is not set
CONFIG_CIFS_XATTR=y
CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_CIFS_DFS_UPCALL is not set
CONFIG_CIFS_FSCACHE=y
CONFIG_CIFS_ACL=y
# CONFIG_CIFS_EXPERIMENTAL is not set
---
~Randy
*** Remember to use Documentation/SubmitChecklist when testing your code ***
^ permalink raw reply
* Re: linux-next: build failure after merge of the final tree (powerpc tree related)
From: Josh Boyer @ 2010-12-03 11:26 UTC (permalink / raw)
To: Benjamin Herrenschmidt
Cc: Stephen Rothwell, linuxppc-dev, linux-next, Paul Mackerras,
linux-kernel, Anton Blanchard
In-Reply-To: <1291355998.32570.417.camel@pasglop>
On Fri, Dec 03, 2010 at 04:59:58PM +1100, Benjamin Herrenschmidt wrote:
>On Fri, 2010-12-03 at 16:32 +1100, Stephen Rothwell wrote:
>>
>> After merging the tree, today's linux-next build (powerpc allmodconfig)
>> failed like this:
>>
>> arch/powerpc/lib/hweight_64.S: Assembler messages:
>> arch/powerpc/lib/hweight_64.S:52: Error: Unrecognized opcode: `popcntw'
>> arch/powerpc/lib/hweight_64.S:77: Error: Unrecognized opcode: `popcntw'
>> arch/powerpc/lib/hweight_64.S:106: Error: Unrecognized opcode: `popcntd'
>>
>> This is with:
>>
>> powerpc64-linux-gcc (GCC) 4.4.0
>> GNU assembler (GNU Binutils) 2.19.1
>>
>> Caused by commit 64ff31287693c1f325cb9cb049569c1611438ef1 ("powerpc: Add
>> support for popcnt instructions").
>
>
>This toolchain is a bit ancient I suppose... Anton, do you reckon we
SLES 11 SP1 still uses gcc 4.3. 4.4.0 is not ancient by any means. Neither is binutils 2.19.1.
>should use .long based macros for these for the time being or just
>require a newer binutils ?
.long macros sound like the proper solution.
josh
^ permalink raw reply
* Re: linux-next: build failure after merge of the final tree (powerpc tree related)
From: Stephen Rothwell @ 2010-12-03 6:08 UTC (permalink / raw)
To: Benjamin Herrenschmidt
Cc: Paul Mackerras, linuxppc-dev, linux-next, linux-kernel,
Anton Blanchard
In-Reply-To: <1291355998.32570.417.camel@pasglop>
[-- Attachment #1: Type: text/plain, Size: 434 bytes --]
On Fri, 03 Dec 2010 16:59:58 +1100 Benjamin Herrenschmidt <benh@kernel.crashing.org> wrote:
>
> This toolchain is a bit ancient I suppose... Anton, do you reckon we
> should use .long based macros for these for the time being or just
> require a newer binutils ?
The currently documented minimum binutils is 2.12 ...
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply
* Re: linux-next: build failure after merge of the final tree (powerpc tree related)
From: Benjamin Herrenschmidt @ 2010-12-03 5:59 UTC (permalink / raw)
To: Stephen Rothwell
Cc: Paul Mackerras, linuxppc-dev, linux-next, linux-kernel,
Anton Blanchard
In-Reply-To: <20101203163206.72258fb8.sfr@canb.auug.org.au>
On Fri, 2010-12-03 at 16:32 +1100, Stephen Rothwell wrote:
>
> After merging the tree, today's linux-next build (powerpc allmodconfig)
> failed like this:
>
> arch/powerpc/lib/hweight_64.S: Assembler messages:
> arch/powerpc/lib/hweight_64.S:52: Error: Unrecognized opcode: `popcntw'
> arch/powerpc/lib/hweight_64.S:77: Error: Unrecognized opcode: `popcntw'
> arch/powerpc/lib/hweight_64.S:106: Error: Unrecognized opcode: `popcntd'
>
> This is with:
>
> powerpc64-linux-gcc (GCC) 4.4.0
> GNU assembler (GNU Binutils) 2.19.1
>
> Caused by commit 64ff31287693c1f325cb9cb049569c1611438ef1 ("powerpc: Add
> support for popcnt instructions").
This toolchain is a bit ancient I suppose... Anton, do you reckon we
should use .long based macros for these for the time being or just
require a newer binutils ?
Cheers,
Ben.
^ permalink raw reply
* linux-next: build failure after merge of the final tree (powerpc tree related)
From: Stephen Rothwell @ 2010-12-03 5:32 UTC (permalink / raw)
To: Benjamin Herrenschmidt, Paul Mackerras, linuxppc-dev
Cc: linux-next, linux-kernel, Anton Blanchard
[-- Attachment #1: Type: text/plain, Size: 688 bytes --]
Hi all,
After merging the tree, today's linux-next build (powerpc allmodconfig)
failed like this:
arch/powerpc/lib/hweight_64.S: Assembler messages:
arch/powerpc/lib/hweight_64.S:52: Error: Unrecognized opcode: `popcntw'
arch/powerpc/lib/hweight_64.S:77: Error: Unrecognized opcode: `popcntw'
arch/powerpc/lib/hweight_64.S:106: Error: Unrecognized opcode: `popcntd'
This is with:
powerpc64-linux-gcc (GCC) 4.4.0
GNU assembler (GNU Binutils) 2.19.1
Caused by commit 64ff31287693c1f325cb9cb049569c1611438ef1 ("powerpc: Add
support for popcnt instructions").
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply
* Re: linux-next: unsigned commit ...
From: Stephen Rothwell @ 2010-12-03 4:46 UTC (permalink / raw)
To: James Morris; +Cc: linux-next, Casey Schaufler
In-Reply-To: <alpine.LRH.2.00.1012031146480.26585@tundra.namei.org>
[-- Attachment #1: Type: text/plain, Size: 1110 bytes --]
Hi James,
On Fri, 3 Dec 2010 12:21:00 +1100 (EST) James Morris <jmorris@namei.org> wrote:
>
> On Fri, 3 Dec 2010, Stephen Rothwell wrote:
>
> I noticed it and pointed it out to Casey, who is converting over to
> pushing git to me instead of posting patch sets.
OK, so learning, I guess.
> If I'm pulling from someone's repo, it means I trust them enough not to
> need to personally review each line of change.
>
> Can this be fixed with git-commit --amend ?
In Casey's tree it can. But then you would need to remerge his tree into
yours. That would leave us with both versions of the commit in your tree.
If, however, you first do a "git reset --hard HEAD^" on your tree
(assuming that the old merge is still at the top), then it will be like
the old merge was never done. This, however will disrupt anyone who's
tree is built on top of yours and has merged your tree (or rebased on top
of it) while that old merge was there (just like if you rebased your
tree).
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply
* linux-next: Tree for December 3
From: Stephen Rothwell @ 2010-12-03 2:04 UTC (permalink / raw)
To: linux-next; +Cc: LKML
[-- Attachment #1: Type: text/plain, Size: 9036 bytes --]
Hi all,
Changes since 20101202:
The v4l-dvb tree still has its build failure for which I applied a patch.
The acpi tree still has its build failure so I used the version from
next-20101201.
The net tree gained a conflict against the wireless-current tree.
The tip tree still has its build failures so I have reverted 3 commits.
----------------------------------------------------------------------------
I have created today's linux-next tree at
git://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
(patches at http://www.kernel.org/pub/linux/kernel/v2.6/next/ ). If you
are tracking the linux-next tree using git, you should not use "git pull"
to do so as that will try to merge the new linux-next release with the
old one. You should use "git fetch" as mentioned in the FAQ on the wiki
(see below).
You can see which trees have been included by looking in the Next/Trees
file in the source. There are also quilt-import.log and merge.log files
in the Next directory. Between each merge, the tree was built with
a ppc64_defconfig for powerpc and an allmodconfig for x86_64. After the
final fixups (if any), it is also built with powerpc allnoconfig (32 and
64 bit), ppc44x_defconfig and allyesconfig (minus
CONFIG_PROFILE_ALL_BRANCHES - this fails its final link) and i386, sparc
and sparc64 defconfig. These builds also have
CONFIG_ENABLE_WARN_DEPRECATED, CONFIG_ENABLE_MUST_CHECK and
CONFIG_DEBUG_INFO disabled when necessary.
Below is a summary of the state of the merge.
We are up to 181 trees (counting Linus' and 26 trees of patches pending
for Linus' tree), more are welcome (even if they are currently empty).
Thanks to those who have contributed, and to those who haven't, please do.
Status of my local build tests will be at
http://kisskb.ellerman.id.au/linux-next . If maintainers want to give
advice about cross compilers/configs that work, we are always open to add
more builds.
Thanks to Randy Dunlap for doing many randconfig builds.
There is a wiki covering stuff to do with linux-next at
http://linux.f-seidel.de/linux-next/pmwiki/ . Thanks to Frank Seidel.
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
$ git checkout master
$ git reset --hard stable
Merging origin/master
Merging fixes/fixes
Merging arm-current/master
Merging m68k-current/for-linus
Merging powerpc-merge/merge
Merging sparc-current/master
Merging scsi-rc-fixes/master
Merging net-current/master
Merging sound-current/for-linus
Merging pci-current/for-linus
Merging wireless-current/master
Merging kbuild-current/rc-fixes
Merging driver-core.current/driver-core-linus
Merging tty.current/tty-linus
Merging usb.current/usb-linus
Merging staging.current/staging-linus
Merging cpufreq-current/fixes
Merging input-current/for-linus
Merging md-current/for-linus
Merging audit-current/for-linus
Merging crypto-current/master
Merging ide-curent/master
Merging dwmw2/master
Merging sh-current/sh-fixes-for-linus
Merging rmobile-current/rmobile-fixes-for-linus
Merging fbdev-current/fbdev-fixes-for-linus
Merging gcl-current/merge
Merging arm/devel
Merging davinci/davinci-next
Merging i.MX/for-next
Merging msm/for-next
Merging omap/for-next
Merging pxa/for-next
Merging samsung/next-samsung
Merging s5p/for-next
Merging tegra/for-next
Merging ux500-core/ux500-core
Merging avr32/avr32-arch
Merging blackfin/for-linus
Merging cris/for-next
Merging ia64/test
Merging m68k/for-next
Merging m68knommu/for-next
Merging microblaze/next
Merging mips/mips-for-linux-next
Merging parisc/next
Merging powerpc/next
Merging 4xx/next
Merging 52xx-and-virtex/next
Merging galak/next
Merging s390/features
Merging sh/sh-latest
Merging rmobile/rmobile-latest
CONFLICT (content): Merge conflict in arch/arm/mach-shmobile/Kconfig
Applying: rmobile: merge fixup for clkdev changes
Merging sparc/master
Merging tile/master
Merging xtensa/master
CONFLICT (content): Merge conflict in arch/xtensa/configs/iss_defconfig
Merging ceph/for-next
Merging cifs/master
Merging configfs/linux-next
Merging ecryptfs/next
Merging ext3/for_next
Merging ext4/next
Merging fatfs/master
Merging fuse/for-next
Merging gfs2/master
Merging hfsplus/for-next
Merging jfs/next
Merging logfs/master
CONFLICT (content): Merge conflict in fs/logfs/logfs.h
Merging nfs/linux-next
Merging nfsd/nfsd-next
Merging nilfs2/for-next
Merging ocfs2/linux-next
Merging omfs/for-next
Merging squashfs/master
Merging udf/for_next
Merging v9fs/for-next
Merging ubifs/linux-next
Merging xfs/master
Merging vfs/for-next
Merging pci/linux-next
CONFLICT (content): Merge conflict in drivers/pci/pci-sysfs.c
Merging hid/for-next
CONFLICT (content): Merge conflict in drivers/hid/hid-input.c
Merging quilt/i2c
Merging bjdooks-i2c/next-i2c
Merging quilt/jdelvare-hwmon
Merging hwmon-staging/hwmon-next
Merging quilt/kernel-doc
Merging v4l-dvb/master
Applying: media: const and __devinitdata do not mix
Merging kbuild/for-next
Merging kconfig/for-next
Merging ide/master
Merging libata/NEXT
Merging infiniband/for-next
Merging acpi/test
$ git reset --hard HEAD^
Merging refs/next/20101201/acpi
Merging idle-test/idle-test
Merging ieee1394/for-next
Merging ubi/linux-next
Merging kvm/linux-next
Merging dlm/next
Merging swiotlb/master
Merging ibft/master
Merging scsi/master
Merging async_tx/next
Merging net/master
CONFLICT (content): Merge conflict in drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
Merging wireless/master
CONFLICT (content): Merge conflict in drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
Merging bluetooth/master
Merging mtd/master
Merging crypto/master
Merging sound/for-next
Merging sound-asoc/for-next
Merging cpufreq/next
Merging quilt/rr
Merging input/next
Merging lsm/for-next
Merging block/for-next
Merging quilt/device-mapper
Merging embedded/master
Merging firmware/master
Merging pcmcia/master
Merging battery/master
Merging leds/for-mm
Merging backlight/for-mm
Merging mmc/mmc-next
Merging kgdb/kgdb-next
Merging slab/for-next
Merging uclinux/for-next
Merging md/for-next
Merging mfd/for-next
CONFLICT (content): Merge conflict in drivers/mfd/wm8994-core.c
Merging hdlc/hdlc-next
Merging drm/drm-next
Merging fbdev/master
Merging viafb/viafb-next
Merging omap_dss2/for-next
Merging voltage/for-next
CONFLICT (content): Merge conflict in drivers/regulator/core.c
Merging security-testing/next
Merging selinux/master
Merging lblnet/master
Merging agp/agp-next
Merging watchdog/master
Merging bdev/master
Merging dwmw2-iommu/master
Merging cputime/cputime
Merging osd/linux-next
Merging jc_docs/docs-next
Merging nommu/master
Merging trivial/for-next
CONFLICT (content): Merge conflict in MAINTAINERS
CONFLICT (content): Merge conflict in drivers/scsi/bfa/bfa_fcpim.c
Merging audit/for-next
Merging suspend/linux-next
Merging fsnotify/for-next
Merging irda/for-next
Merging catalin/for-next
Merging alacrity/linux-next
CONFLICT (content): Merge conflict in drivers/Makefile
CONFLICT (content): Merge conflict in include/linux/Kbuild
CONFLICT (content): Merge conflict in lib/Kconfig
Merging i7core_edac/linux_next
Merging i7300_edac/linux_next
Merging devicetree/next-devicetree
Merging spi/next-spi
Merging tip/auto-latest
[master c0605ba] Revert "x86, nmi_watchdog: Remove all stub function calls from old nmi_watchdog"
[master fcb8eb6] Revert "x86, nmi_watchdog: Remove the old nmi_watchdog"
[master 637fc62] Revert "perf, arch: Cleanup perf-pmu init vs lockup-detector"
Merging rcu/rcu/next
Merging oprofile/for-next
Merging xen/upstream/xen
Merging swiotlb-xen/master
Merging xen-pvhvm/linux-next
Merging edac-amd/for-next
Merging percpu/for-next
Merging workqueues/for-next
Merging sfi/sfi-test
Merging asm-generic/next
Merging drivers-x86/linux-next
Merging hwpoison/hwpoison
Merging sysctl/master
Merging driver-core/driver-core-next
Merging tty/tty-next
Merging usb/usb-next
Merging staging/staging-next
CONFLICT (content): Merge conflict in drivers/staging/batman-adv/hard-interface.c
CONFLICT (content): Merge conflict in drivers/staging/batman-adv/soft-interface.c
CONFLICT (delete/modify): drivers/staging/winbond/sysdef.h deleted in staging/staging-next and modified in HEAD. Version HEAD of drivers/staging/winbond/sysdef.h left in tree.
$ git rm -f drivers/staging/winbond/sysdef.h
Merging slabh/slabh
Merging bkl-trivial/trivial
Merging bkl-llseek/llseek
Merging bkl-vfs/vfs
Merging bkl-config/config
CONFLICT (content): Merge conflict in arch/powerpc/kernel/setup_64.c
CONFLICT (content): Merge conflict in include/linux/hardirq.h
CONFLICT (content): Merge conflict in include/linux/smp_lock.h
Merging irqflags/master
Merging cleancache/linux-next
CONFLICT (content): Merge conflict in fs/ocfs2/super.c
CONFLICT (content): Merge conflict in include/linux/fs.h
CONFLICT (content): Merge conflict in mm/Kconfig
Merging scsi-post-merge/merge-base:master
[-- Attachment #2: Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply
* Re: linux-next: unsigned commit ...
From: James Morris @ 2010-12-03 1:21 UTC (permalink / raw)
To: Stephen Rothwell; +Cc: linux-next, Casey Schaufler
In-Reply-To: <20101203092928.367d45c0.sfr@canb.auug.org.au>
On Fri, 3 Dec 2010, Stephen Rothwell wrote:
> Hi James,
>
> Commit 676dac4b1bee0469d6932f698aeb77e8489f5861 ("This patch adds a new
> security attribute to Smack called") that was added to your tree today
> has no Signed-off-by and could do with a better summary line in the
> commit message. And probably a better explanation of what it does.
>
> Makes me wonder about the level of review it received :-(
I noticed it and pointed it out to Casey, who is converting over to
pushing git to me instead of posting patch sets.
If I'm pulling from someone's repo, it means I trust them enough not to
need to personally review each line of change.
Can this be fixed with git-commit --amend ?
- James
--
James Morris
<jmorris@namei.org>
^ permalink raw reply
* linux-next: manual merge of the net tree with the wireless-current tree
From: Stephen Rothwell @ 2010-12-02 23:45 UTC (permalink / raw)
To: David Miller, netdev
Cc: linux-next, linux-kernel, Senthil Balasubramanian, Felix Fietkau,
John W. Linville
Hi all,
Today's linux-next merge of the net tree got a conflict in
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c between commit
e702ba18f25887c76d26c8a85cc1706463c62e9a ("ath9k_hw: fix endian issues
with CTLs on AR9003") from the wireless-current tree and commits
3092354970381fb8b6439fb4def0c34632277ae9 ("ath9k_hw: add eeprom templates
for ar9003 family chipsets") and f4475a6e52fce8d951a96c763f36b835bf89fdec
("ath9k_hw: Enable strong signal detection for AR9003") from the net tree.
There have been many more fields added that will need to be wrapped in
CTL(). I just fixed up the conflicting case. It looks like this has
been fixed up by the wireless-current tree being merged into the wireless
tree and and so will go away when the wireless tree is merged into the
net tree again.
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
diff --cc drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index a7b82f0,3161a59..0000000
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@@ -55,17 -57,2327 +57,2329 @@@
#define SUB_NUM_CTL_MODES_AT_5G_40 2 /* excluding HT40, EXT-OFDM */
#define SUB_NUM_CTL_MODES_AT_2G_40 3 /* excluding HT40, EXT-OFDM, EXT-CCK */
+#define CTL(_tpower, _flag) ((_tpower) | ((_flag) << 6))
+
+ static int ar9003_hw_power_interpolate(int32_t x,
+ int32_t *px, int32_t *py, u_int16_t np);
static const struct ar9300_eeprom ar9300_default = {
.eepromVersion = 2,
- .templateVersion = 2,
- .macAddr = {1, 2, 3, 4, 5, 6},
- .custData = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
- 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},
+ .templateVersion = 2,
+ .macAddr = {1, 2, 3, 4, 5, 6},
+ .custData = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0},
+ .baseEepHeader = {
+ .regDmn = { LE16(0), LE16(0x1f) },
+ .txrxMask = 0x77, /* 4 bits tx and 4 bits rx */
+ .opCapFlags = {
+ .opFlags = AR9300_OPFLAGS_11G | AR9300_OPFLAGS_11A,
+ .eepMisc = 0,
+ },
+ .rfSilent = 0,
+ .blueToothOptions = 0,
+ .deviceCap = 0,
+ .deviceType = 5, /* takes lower byte in eeprom location */
+ .pwrTableOffset = AR9300_PWR_TABLE_OFFSET,
+ .params_for_tuning_caps = {0, 0},
+ .featureEnable = 0x0c,
+ /*
+ * bit0 - enable tx temp comp - disabled
+ * bit1 - enable tx volt comp - disabled
+ * bit2 - enable fastClock - enabled
+ * bit3 - enable doubling - enabled
+ * bit4 - enable internal regulator - disabled
+ * bit5 - enable pa predistortion - disabled
+ */
+ .miscConfiguration = 0, /* bit0 - turn down drivestrength */
+ .eepromWriteEnableGpio = 3,
+ .wlanDisableGpio = 0,
+ .wlanLedGpio = 8,
+ .rxBandSelectGpio = 0xff,
+ .txrxgain = 0,
+ .swreg = 0,
+ },
+ .modalHeader2G = {
+ /* ar9300_modal_eep_header 2g */
+ /* 4 idle,t1,t2,b(4 bits per setting) */
+ .antCtrlCommon = LE32(0x110),
+ /* 4 ra1l1, ra2l1, ra1l2, ra2l2, ra12 */
+ .antCtrlCommon2 = LE32(0x22222),
+
+ /*
+ * antCtrlChain[AR9300_MAX_CHAINS]; 6 idle, t, r,
+ * rx1, rx12, b (2 bits each)
+ */
+ .antCtrlChain = { LE16(0x150), LE16(0x150), LE16(0x150) },
+
+ /*
+ * xatten1DB[AR9300_MAX_CHAINS]; 3 xatten1_db
+ * for ar9280 (0xa20c/b20c 5:0)
+ */
+ .xatten1DB = {0, 0, 0},
+
+ /*
+ * xatten1Margin[AR9300_MAX_CHAINS]; 3 xatten1_margin
+ * for ar9280 (0xa20c/b20c 16:12
+ */
+ .xatten1Margin = {0, 0, 0},
+ .tempSlope = 36,
+ .voltSlope = 0,
+
+ /*
+ * spurChans[OSPREY_EEPROM_MODAL_SPURS]; spur
+ * channels in usual fbin coding format
+ */
+ .spurChans = {0, 0, 0, 0, 0},
+
+ /*
+ * noiseFloorThreshCh[AR9300_MAX_CHAINS]; 3 Check
+ * if the register is per chain
+ */
+ .noiseFloorThreshCh = {-1, 0, 0},
+ .ob = {1, 1, 1},/* 3 chain */
+ .db_stage2 = {1, 1, 1}, /* 3 chain */
+ .db_stage3 = {0, 0, 0},
+ .db_stage4 = {0, 0, 0},
+ .xpaBiasLvl = 0,
+ .txFrameToDataStart = 0x0e,
+ .txFrameToPaOn = 0x0e,
+ .txClip = 3, /* 4 bits tx_clip, 4 bits dac_scale_cck */
+ .antennaGain = 0,
+ .switchSettling = 0x2c,
+ .adcDesiredSize = -30,
+ .txEndToXpaOff = 0,
+ .txEndToRxOn = 0x2,
+ .txFrameToXpaOn = 0xe,
+ .thresh62 = 28,
+ .papdRateMaskHt20 = LE32(0x0cf0e0e0),
+ .papdRateMaskHt40 = LE32(0x6cf0e0e0),
+ .futureModal = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ },
+ },
+ .base_ext1 = {
+ .ant_div_control = 0,
+ .future = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}
+ },
+ .calFreqPier2G = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1),
+ },
+ /* ar9300_cal_data_per_freq_op_loop 2g */
+ .calPierData2G = {
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ },
+ .calTarget_freqbin_Cck = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2484, 1),
+ },
+ .calTarget_freqbin_2G = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTarget_freqbin_2GHT20 = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTarget_freqbin_2GHT40 = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTargetPowerCck = {
+ /* 1L-5L,5S,11L,11S */
+ { {36, 36, 36, 36} },
+ { {36, 36, 36, 36} },
+ },
+ .calTargetPower2G = {
+ /* 6-24,36,48,54 */
+ { {32, 32, 28, 24} },
+ { {32, 32, 28, 24} },
+ { {32, 32, 28, 24} },
+ },
+ .calTargetPower2GHT20 = {
+ { {32, 32, 32, 32, 28, 20, 32, 32, 28, 20, 32, 32, 28, 20} },
+ { {32, 32, 32, 32, 28, 20, 32, 32, 28, 20, 32, 32, 28, 20} },
+ { {32, 32, 32, 32, 28, 20, 32, 32, 28, 20, 32, 32, 28, 20} },
+ },
+ .calTargetPower2GHT40 = {
+ { {32, 32, 32, 32, 28, 20, 32, 32, 28, 20, 32, 32, 28, 20} },
+ { {32, 32, 32, 32, 28, 20, 32, 32, 28, 20, 32, 32, 28, 20} },
+ { {32, 32, 32, 32, 28, 20, 32, 32, 28, 20, 32, 32, 28, 20} },
+ },
+ .ctlIndex_2G = {
+ 0x11, 0x12, 0x15, 0x17, 0x41, 0x42,
+ 0x45, 0x47, 0x31, 0x32, 0x35, 0x37,
+ },
+ .ctl_freqbin_2G = {
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2457, 1),
+ FREQ2FBIN(2462, 1)
+ },
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2462, 1),
+ 0xFF,
+ },
+
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2462, 1),
+ 0xFF,
+ },
+ {
+ FREQ2FBIN(2422, 1),
+ FREQ2FBIN(2427, 1),
+ FREQ2FBIN(2447, 1),
+ FREQ2FBIN(2452, 1)
+ },
+
+ {
+ /* Data[4].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[4].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[4].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ /* Data[4].ctlEdges[3].bChannel */ FREQ2FBIN(2484, 1),
+ },
+
+ {
+ /* Data[5].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[5].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[5].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ 0,
+ },
+
+ {
+ /* Data[6].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[6].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2472, 1),
+ 0,
+ },
+
+ {
+ /* Data[7].ctlEdges[0].bChannel */ FREQ2FBIN(2422, 1),
+ /* Data[7].ctlEdges[1].bChannel */ FREQ2FBIN(2427, 1),
+ /* Data[7].ctlEdges[2].bChannel */ FREQ2FBIN(2447, 1),
+ /* Data[7].ctlEdges[3].bChannel */ FREQ2FBIN(2462, 1),
+ },
+
+ {
+ /* Data[8].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[8].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[8].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ },
+
+ {
+ /* Data[9].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[9].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[9].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ 0
+ },
+
+ {
+ /* Data[10].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[10].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[10].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ 0
+ },
+
+ {
+ /* Data[11].ctlEdges[0].bChannel */ FREQ2FBIN(2422, 1),
+ /* Data[11].ctlEdges[1].bChannel */ FREQ2FBIN(2427, 1),
+ /* Data[11].ctlEdges[2].bChannel */ FREQ2FBIN(2447, 1),
+ /* Data[11].ctlEdges[3].bChannel */ FREQ2FBIN(2462, 1),
+ }
+ },
+ .ctlPowerData_2G = {
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 1}, {60, 0}, {60, 0}, {60, 1} } },
+
+ { { {60, 1}, {60, 0}, {0, 0}, {0, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 1} } },
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 1} } },
+ },
+ .modalHeader5G = {
+ /* 4 idle,t1,t2,b (4 bits per setting) */
+ .antCtrlCommon = LE32(0x110),
+ /* 4 ra1l1, ra2l1, ra1l2,ra2l2,ra12 */
+ .antCtrlCommon2 = LE32(0x22222),
+ /* antCtrlChain 6 idle, t,r,rx1,rx12,b (2 bits each) */
+ .antCtrlChain = {
+ LE16(0x000), LE16(0x000), LE16(0x000),
+ },
+ /* xatten1DB 3 xatten1_db for AR9280 (0xa20c/b20c 5:0) */
+ .xatten1DB = {0, 0, 0},
+
+ /*
+ * xatten1Margin[AR9300_MAX_CHAINS]; 3 xatten1_margin
+ * for merlin (0xa20c/b20c 16:12
+ */
+ .xatten1Margin = {0, 0, 0},
+ .tempSlope = 68,
+ .voltSlope = 0,
+ /* spurChans spur channels in usual fbin coding format */
+ .spurChans = {0, 0, 0, 0, 0},
+ /* noiseFloorThreshCh Check if the register is per chain */
+ .noiseFloorThreshCh = {-1, 0, 0},
+ .ob = {3, 3, 3}, /* 3 chain */
+ .db_stage2 = {3, 3, 3}, /* 3 chain */
+ .db_stage3 = {3, 3, 3}, /* doesn't exist for 2G */
+ .db_stage4 = {3, 3, 3}, /* don't exist for 2G */
+ .xpaBiasLvl = 0,
+ .txFrameToDataStart = 0x0e,
+ .txFrameToPaOn = 0x0e,
+ .txClip = 3, /* 4 bits tx_clip, 4 bits dac_scale_cck */
+ .antennaGain = 0,
+ .switchSettling = 0x2d,
+ .adcDesiredSize = -30,
+ .txEndToXpaOff = 0,
+ .txEndToRxOn = 0x2,
+ .txFrameToXpaOn = 0xe,
+ .thresh62 = 28,
+ .papdRateMaskHt20 = LE32(0x0c80c080),
+ .papdRateMaskHt40 = LE32(0x0080c080),
+ .futureModal = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ },
+ },
+ .base_ext2 = {
+ .tempSlopeLow = 0,
+ .tempSlopeHigh = 0,
+ .xatten1DBLow = {0, 0, 0},
+ .xatten1MarginLow = {0, 0, 0},
+ .xatten1DBHigh = {0, 0, 0},
+ .xatten1MarginHigh = {0, 0, 0}
+ },
+ .calFreqPier5G = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5220, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5725, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calPierData5G = {
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+
+ },
+ .calTarget_freqbin_5G = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5220, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5725, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTarget_freqbin_5GHT20 = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5240, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5700, 0),
+ FREQ2FBIN(5745, 0),
+ FREQ2FBIN(5725, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTarget_freqbin_5GHT40 = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5240, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5700, 0),
+ FREQ2FBIN(5745, 0),
+ FREQ2FBIN(5725, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTargetPower5G = {
+ /* 6-24,36,48,54 */
+ { {20, 20, 20, 10} },
+ { {20, 20, 20, 10} },
+ { {20, 20, 20, 10} },
+ { {20, 20, 20, 10} },
+ { {20, 20, 20, 10} },
+ { {20, 20, 20, 10} },
+ { {20, 20, 20, 10} },
+ { {20, 20, 20, 10} },
+ },
+ .calTargetPower5GHT20 = {
+ /*
+ * 0_8_16,1-3_9-11_17-19,
+ * 4,5,6,7,12,13,14,15,20,21,22,23
+ */
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ },
+ .calTargetPower5GHT40 = {
+ /*
+ * 0_8_16,1-3_9-11_17-19,
+ * 4,5,6,7,12,13,14,15,20,21,22,23
+ */
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ { {20, 20, 10, 10, 0, 0, 10, 10, 0, 0, 10, 10, 0, 0} },
+ },
+ .ctlIndex_5G = {
+ 0x10, 0x16, 0x18, 0x40, 0x46,
+ 0x48, 0x30, 0x36, 0x38
+ },
+ .ctl_freqbin_5G = {
+ {
+ /* Data[0].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[0].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[0].ctlEdges[2].bChannel */ FREQ2FBIN(5280, 0),
+ /* Data[0].ctlEdges[3].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[0].ctlEdges[4].bChannel */ FREQ2FBIN(5600, 0),
+ /* Data[0].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[0].ctlEdges[6].bChannel */ FREQ2FBIN(5745, 0),
+ /* Data[0].ctlEdges[7].bChannel */ FREQ2FBIN(5825, 0)
+ },
+ {
+ /* Data[1].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[1].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[1].ctlEdges[2].bChannel */ FREQ2FBIN(5280, 0),
+ /* Data[1].ctlEdges[3].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[1].ctlEdges[4].bChannel */ FREQ2FBIN(5520, 0),
+ /* Data[1].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[1].ctlEdges[6].bChannel */ FREQ2FBIN(5745, 0),
+ /* Data[1].ctlEdges[7].bChannel */ FREQ2FBIN(5825, 0)
+ },
+
+ {
+ /* Data[2].ctlEdges[0].bChannel */ FREQ2FBIN(5190, 0),
+ /* Data[2].ctlEdges[1].bChannel */ FREQ2FBIN(5230, 0),
+ /* Data[2].ctlEdges[2].bChannel */ FREQ2FBIN(5270, 0),
+ /* Data[2].ctlEdges[3].bChannel */ FREQ2FBIN(5310, 0),
+ /* Data[2].ctlEdges[4].bChannel */ FREQ2FBIN(5510, 0),
+ /* Data[2].ctlEdges[5].bChannel */ FREQ2FBIN(5550, 0),
+ /* Data[2].ctlEdges[6].bChannel */ FREQ2FBIN(5670, 0),
+ /* Data[2].ctlEdges[7].bChannel */ FREQ2FBIN(5755, 0)
+ },
+
+ {
+ /* Data[3].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[3].ctlEdges[1].bChannel */ FREQ2FBIN(5200, 0),
+ /* Data[3].ctlEdges[2].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[3].ctlEdges[3].bChannel */ FREQ2FBIN(5320, 0),
+ /* Data[3].ctlEdges[4].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[3].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[3].ctlEdges[6].bChannel */ 0xFF,
+ /* Data[3].ctlEdges[7].bChannel */ 0xFF,
+ },
+
+ {
+ /* Data[4].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[4].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[4].ctlEdges[2].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[4].ctlEdges[3].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[4].ctlEdges[4].bChannel */ 0xFF,
+ /* Data[4].ctlEdges[5].bChannel */ 0xFF,
+ /* Data[4].ctlEdges[6].bChannel */ 0xFF,
+ /* Data[4].ctlEdges[7].bChannel */ 0xFF,
+ },
+
+ {
+ /* Data[5].ctlEdges[0].bChannel */ FREQ2FBIN(5190, 0),
+ /* Data[5].ctlEdges[1].bChannel */ FREQ2FBIN(5270, 0),
+ /* Data[5].ctlEdges[2].bChannel */ FREQ2FBIN(5310, 0),
+ /* Data[5].ctlEdges[3].bChannel */ FREQ2FBIN(5510, 0),
+ /* Data[5].ctlEdges[4].bChannel */ FREQ2FBIN(5590, 0),
+ /* Data[5].ctlEdges[5].bChannel */ FREQ2FBIN(5670, 0),
+ /* Data[5].ctlEdges[6].bChannel */ 0xFF,
+ /* Data[5].ctlEdges[7].bChannel */ 0xFF
+ },
+
+ {
+ /* Data[6].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[6].ctlEdges[1].bChannel */ FREQ2FBIN(5200, 0),
+ /* Data[6].ctlEdges[2].bChannel */ FREQ2FBIN(5220, 0),
+ /* Data[6].ctlEdges[3].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[6].ctlEdges[4].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[6].ctlEdges[5].bChannel */ FREQ2FBIN(5600, 0),
+ /* Data[6].ctlEdges[6].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[6].ctlEdges[7].bChannel */ FREQ2FBIN(5745, 0)
+ },
+
+ {
+ /* Data[7].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[7].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[7].ctlEdges[2].bChannel */ FREQ2FBIN(5320, 0),
+ /* Data[7].ctlEdges[3].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[7].ctlEdges[4].bChannel */ FREQ2FBIN(5560, 0),
+ /* Data[7].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[7].ctlEdges[6].bChannel */ FREQ2FBIN(5745, 0),
+ /* Data[7].ctlEdges[7].bChannel */ FREQ2FBIN(5825, 0)
+ },
+
+ {
+ /* Data[8].ctlEdges[0].bChannel */ FREQ2FBIN(5190, 0),
+ /* Data[8].ctlEdges[1].bChannel */ FREQ2FBIN(5230, 0),
+ /* Data[8].ctlEdges[2].bChannel */ FREQ2FBIN(5270, 0),
+ /* Data[8].ctlEdges[3].bChannel */ FREQ2FBIN(5510, 0),
+ /* Data[8].ctlEdges[4].bChannel */ FREQ2FBIN(5550, 0),
+ /* Data[8].ctlEdges[5].bChannel */ FREQ2FBIN(5670, 0),
+ /* Data[8].ctlEdges[6].bChannel */ FREQ2FBIN(5755, 0),
+ /* Data[8].ctlEdges[7].bChannel */ FREQ2FBIN(5795, 0)
+ }
+ },
+ .ctlPowerData_5G = {
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 0}, {60, 1}, {60, 0}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ }
+ },
+ {
+ {
+ {60, 0}, {60, 1}, {60, 1}, {60, 0},
+ {60, 1}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ {60, 0}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 0}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 0}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 0}, {60, 1},
+ }
+ },
+ }
+ };
+
+ static const struct ar9300_eeprom ar9300_x113 = {
+ .eepromVersion = 2,
+ .templateVersion = 6,
+ .macAddr = {0x00, 0x03, 0x7f, 0x0, 0x0, 0x0},
+ .custData = {"x113-023-f0000"},
+ .baseEepHeader = {
+ .regDmn = { LE16(0), LE16(0x1f) },
+ .txrxMask = 0x77, /* 4 bits tx and 4 bits rx */
+ .opCapFlags = {
+ .opFlags = AR9300_OPFLAGS_11G | AR9300_OPFLAGS_11A,
+ .eepMisc = 0,
+ },
+ .rfSilent = 0,
+ .blueToothOptions = 0,
+ .deviceCap = 0,
+ .deviceType = 5, /* takes lower byte in eeprom location */
+ .pwrTableOffset = AR9300_PWR_TABLE_OFFSET,
+ .params_for_tuning_caps = {0, 0},
+ .featureEnable = 0x0d,
+ /*
+ * bit0 - enable tx temp comp - disabled
+ * bit1 - enable tx volt comp - disabled
+ * bit2 - enable fastClock - enabled
+ * bit3 - enable doubling - enabled
+ * bit4 - enable internal regulator - disabled
+ * bit5 - enable pa predistortion - disabled
+ */
+ .miscConfiguration = 0, /* bit0 - turn down drivestrength */
+ .eepromWriteEnableGpio = 6,
+ .wlanDisableGpio = 0,
+ .wlanLedGpio = 8,
+ .rxBandSelectGpio = 0xff,
+ .txrxgain = 0x21,
+ .swreg = 0,
+ },
+ .modalHeader2G = {
+ /* ar9300_modal_eep_header 2g */
+ /* 4 idle,t1,t2,b(4 bits per setting) */
+ .antCtrlCommon = LE32(0x110),
+ /* 4 ra1l1, ra2l1, ra1l2, ra2l2, ra12 */
+ .antCtrlCommon2 = LE32(0x44444),
+
+ /*
+ * antCtrlChain[AR9300_MAX_CHAINS]; 6 idle, t, r,
+ * rx1, rx12, b (2 bits each)
+ */
+ .antCtrlChain = { LE16(0x150), LE16(0x150), LE16(0x150) },
+
+ /*
+ * xatten1DB[AR9300_MAX_CHAINS]; 3 xatten1_db
+ * for ar9280 (0xa20c/b20c 5:0)
+ */
+ .xatten1DB = {0, 0, 0},
+
+ /*
+ * xatten1Margin[AR9300_MAX_CHAINS]; 3 xatten1_margin
+ * for ar9280 (0xa20c/b20c 16:12
+ */
+ .xatten1Margin = {0, 0, 0},
+ .tempSlope = 25,
+ .voltSlope = 0,
+
+ /*
+ * spurChans[OSPREY_EEPROM_MODAL_SPURS]; spur
+ * channels in usual fbin coding format
+ */
+ .spurChans = {FREQ2FBIN(2464, 1), 0, 0, 0, 0},
+
+ /*
+ * noiseFloorThreshCh[AR9300_MAX_CHAINS]; 3 Check
+ * if the register is per chain
+ */
+ .noiseFloorThreshCh = {-1, 0, 0},
+ .ob = {1, 1, 1},/* 3 chain */
+ .db_stage2 = {1, 1, 1}, /* 3 chain */
+ .db_stage3 = {0, 0, 0},
+ .db_stage4 = {0, 0, 0},
+ .xpaBiasLvl = 0,
+ .txFrameToDataStart = 0x0e,
+ .txFrameToPaOn = 0x0e,
+ .txClip = 3, /* 4 bits tx_clip, 4 bits dac_scale_cck */
+ .antennaGain = 0,
+ .switchSettling = 0x2c,
+ .adcDesiredSize = -30,
+ .txEndToXpaOff = 0,
+ .txEndToRxOn = 0x2,
+ .txFrameToXpaOn = 0xe,
+ .thresh62 = 28,
+ .papdRateMaskHt20 = LE32(0x0c80c080),
+ .papdRateMaskHt40 = LE32(0x0080c080),
+ .futureModal = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ },
+ },
+ .base_ext1 = {
+ .ant_div_control = 0,
+ .future = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}
+ },
+ .calFreqPier2G = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1),
+ },
+ /* ar9300_cal_data_per_freq_op_loop 2g */
+ .calPierData2G = {
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ },
+ .calTarget_freqbin_Cck = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2472, 1),
+ },
+ .calTarget_freqbin_2G = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTarget_freqbin_2GHT20 = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTarget_freqbin_2GHT40 = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTargetPowerCck = {
+ /* 1L-5L,5S,11L,11S */
+ { {34, 34, 34, 34} },
+ { {34, 34, 34, 34} },
+ },
+ .calTargetPower2G = {
+ /* 6-24,36,48,54 */
+ { {34, 34, 32, 32} },
+ { {34, 34, 32, 32} },
+ { {34, 34, 32, 32} },
+ },
+ .calTargetPower2GHT20 = {
+ { {32, 32, 32, 32, 32, 28, 32, 32, 30, 28, 0, 0, 0, 0} },
+ { {32, 32, 32, 32, 32, 28, 32, 32, 30, 28, 0, 0, 0, 0} },
+ { {32, 32, 32, 32, 32, 28, 32, 32, 30, 28, 0, 0, 0, 0} },
+ },
+ .calTargetPower2GHT40 = {
+ { {30, 30, 30, 30, 30, 28, 30, 30, 28, 26, 0, 0, 0, 0} },
+ { {30, 30, 30, 30, 30, 28, 30, 30, 28, 26, 0, 0, 0, 0} },
+ { {30, 30, 30, 30, 30, 28, 30, 30, 28, 26, 0, 0, 0, 0} },
+ },
+ .ctlIndex_2G = {
+ 0x11, 0x12, 0x15, 0x17, 0x41, 0x42,
+ 0x45, 0x47, 0x31, 0x32, 0x35, 0x37,
+ },
+ .ctl_freqbin_2G = {
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2457, 1),
+ FREQ2FBIN(2462, 1)
+ },
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2462, 1),
+ 0xFF,
+ },
+
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2462, 1),
+ 0xFF,
+ },
+ {
+ FREQ2FBIN(2422, 1),
+ FREQ2FBIN(2427, 1),
+ FREQ2FBIN(2447, 1),
+ FREQ2FBIN(2452, 1)
+ },
+
+ {
+ /* Data[4].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[4].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[4].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ /* Data[4].ctlEdges[3].bChannel */ FREQ2FBIN(2484, 1),
+ },
+
+ {
+ /* Data[5].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[5].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[5].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ 0,
+ },
+
+ {
+ /* Data[6].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[6].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2472, 1),
+ 0,
+ },
+
+ {
+ /* Data[7].ctlEdges[0].bChannel */ FREQ2FBIN(2422, 1),
+ /* Data[7].ctlEdges[1].bChannel */ FREQ2FBIN(2427, 1),
+ /* Data[7].ctlEdges[2].bChannel */ FREQ2FBIN(2447, 1),
+ /* Data[7].ctlEdges[3].bChannel */ FREQ2FBIN(2462, 1),
+ },
+
+ {
+ /* Data[8].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[8].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[8].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ },
+
+ {
+ /* Data[9].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[9].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[9].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ 0
+ },
+
+ {
+ /* Data[10].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[10].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[10].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ 0
+ },
+
+ {
+ /* Data[11].ctlEdges[0].bChannel */ FREQ2FBIN(2422, 1),
+ /* Data[11].ctlEdges[1].bChannel */ FREQ2FBIN(2427, 1),
+ /* Data[11].ctlEdges[2].bChannel */ FREQ2FBIN(2447, 1),
+ /* Data[11].ctlEdges[3].bChannel */ FREQ2FBIN(2462, 1),
+ }
+ },
+ .ctlPowerData_2G = {
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 1}, {60, 0}, {60, 0}, {60, 1} } },
+
+ { { {60, 1}, {60, 0}, {0, 0}, {0, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 1} } },
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 1} } },
+ },
+ .modalHeader5G = {
+ /* 4 idle,t1,t2,b (4 bits per setting) */
+ .antCtrlCommon = LE32(0x220),
+ /* 4 ra1l1, ra2l1, ra1l2,ra2l2,ra12 */
+ .antCtrlCommon2 = LE32(0x11111),
+ /* antCtrlChain 6 idle, t,r,rx1,rx12,b (2 bits each) */
+ .antCtrlChain = {
+ LE16(0x150), LE16(0x150), LE16(0x150),
+ },
+ /* xatten1DB 3 xatten1_db for AR9280 (0xa20c/b20c 5:0) */
+ .xatten1DB = {0, 0, 0},
+
+ /*
+ * xatten1Margin[AR9300_MAX_CHAINS]; 3 xatten1_margin
+ * for merlin (0xa20c/b20c 16:12
+ */
+ .xatten1Margin = {0, 0, 0},
+ .tempSlope = 68,
+ .voltSlope = 0,
+ /* spurChans spur channels in usual fbin coding format */
+ .spurChans = {FREQ2FBIN(5500, 0), 0, 0, 0, 0},
+ /* noiseFloorThreshCh Check if the register is per chain */
+ .noiseFloorThreshCh = {-1, 0, 0},
+ .ob = {3, 3, 3}, /* 3 chain */
+ .db_stage2 = {3, 3, 3}, /* 3 chain */
+ .db_stage3 = {3, 3, 3}, /* doesn't exist for 2G */
+ .db_stage4 = {3, 3, 3}, /* don't exist for 2G */
+ .xpaBiasLvl = 0,
+ .txFrameToDataStart = 0x0e,
+ .txFrameToPaOn = 0x0e,
+ .txClip = 3, /* 4 bits tx_clip, 4 bits dac_scale_cck */
+ .antennaGain = 0,
+ .switchSettling = 0x2d,
+ .adcDesiredSize = -30,
+ .txEndToXpaOff = 0,
+ .txEndToRxOn = 0x2,
+ .txFrameToXpaOn = 0xe,
+ .thresh62 = 28,
+ .papdRateMaskHt20 = LE32(0x0cf0e0e0),
+ .papdRateMaskHt40 = LE32(0x6cf0e0e0),
+ .futureModal = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ },
+ },
+ .base_ext2 = {
+ .tempSlopeLow = 72,
+ .tempSlopeHigh = 105,
+ .xatten1DBLow = {0, 0, 0},
+ .xatten1MarginLow = {0, 0, 0},
+ .xatten1DBHigh = {0, 0, 0},
+ .xatten1MarginHigh = {0, 0, 0}
+ },
+ .calFreqPier5G = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5240, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5745, 0),
+ FREQ2FBIN(5785, 0)
+ },
+ .calPierData5G = {
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+
+ },
+ .calTarget_freqbin_5G = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5220, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5745, 0),
+ FREQ2FBIN(5785, 0)
+ },
+ .calTarget_freqbin_5GHT20 = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5240, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5700, 0),
+ FREQ2FBIN(5745, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTarget_freqbin_5GHT40 = {
+ FREQ2FBIN(5190, 0),
+ FREQ2FBIN(5230, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5410, 0),
+ FREQ2FBIN(5510, 0),
+ FREQ2FBIN(5670, 0),
+ FREQ2FBIN(5755, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTargetPower5G = {
+ /* 6-24,36,48,54 */
+ { {42, 40, 40, 34} },
+ { {42, 40, 40, 34} },
+ { {42, 40, 40, 34} },
+ { {42, 40, 40, 34} },
+ { {42, 40, 40, 34} },
+ { {42, 40, 40, 34} },
+ { {42, 40, 40, 34} },
+ { {42, 40, 40, 34} },
+ },
+ .calTargetPower5GHT20 = {
+ /*
+ * 0_8_16,1-3_9-11_17-19,
+ * 4,5,6,7,12,13,14,15,20,21,22,23
+ */
+ { {40, 40, 40, 40, 32, 28, 40, 40, 32, 28, 40, 40, 32, 20} },
+ { {40, 40, 40, 40, 32, 28, 40, 40, 32, 28, 40, 40, 32, 20} },
+ { {40, 40, 40, 40, 32, 28, 40, 40, 32, 28, 40, 40, 32, 20} },
+ { {40, 40, 40, 40, 32, 28, 40, 40, 32, 28, 40, 40, 32, 20} },
+ { {40, 40, 40, 40, 32, 28, 40, 40, 32, 28, 40, 40, 32, 20} },
+ { {40, 40, 40, 40, 32, 28, 40, 40, 32, 28, 40, 40, 32, 20} },
+ { {38, 38, 38, 38, 32, 28, 38, 38, 32, 28, 38, 38, 32, 26} },
+ { {36, 36, 36, 36, 32, 28, 36, 36, 32, 28, 36, 36, 32, 26} },
+ },
+ .calTargetPower5GHT40 = {
+ /*
+ * 0_8_16,1-3_9-11_17-19,
+ * 4,5,6,7,12,13,14,15,20,21,22,23
+ */
+ { {40, 40, 40, 38, 30, 26, 40, 40, 30, 26, 40, 40, 30, 24} },
+ { {40, 40, 40, 38, 30, 26, 40, 40, 30, 26, 40, 40, 30, 24} },
+ { {40, 40, 40, 38, 30, 26, 40, 40, 30, 26, 40, 40, 30, 24} },
+ { {40, 40, 40, 38, 30, 26, 40, 40, 30, 26, 40, 40, 30, 24} },
+ { {40, 40, 40, 38, 30, 26, 40, 40, 30, 26, 40, 40, 30, 24} },
+ { {40, 40, 40, 38, 30, 26, 40, 40, 30, 26, 40, 40, 30, 24} },
+ { {36, 36, 36, 36, 30, 26, 36, 36, 30, 26, 36, 36, 30, 24} },
+ { {34, 34, 34, 34, 30, 26, 34, 34, 30, 26, 34, 34, 30, 24} },
+ },
+ .ctlIndex_5G = {
+ 0x10, 0x16, 0x18, 0x40, 0x46,
+ 0x48, 0x30, 0x36, 0x38
+ },
+ .ctl_freqbin_5G = {
+ {
+ /* Data[0].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[0].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[0].ctlEdges[2].bChannel */ FREQ2FBIN(5280, 0),
+ /* Data[0].ctlEdges[3].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[0].ctlEdges[4].bChannel */ FREQ2FBIN(5600, 0),
+ /* Data[0].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[0].ctlEdges[6].bChannel */ FREQ2FBIN(5745, 0),
+ /* Data[0].ctlEdges[7].bChannel */ FREQ2FBIN(5825, 0)
+ },
+ {
+ /* Data[1].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[1].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[1].ctlEdges[2].bChannel */ FREQ2FBIN(5280, 0),
+ /* Data[1].ctlEdges[3].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[1].ctlEdges[4].bChannel */ FREQ2FBIN(5520, 0),
+ /* Data[1].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[1].ctlEdges[6].bChannel */ FREQ2FBIN(5745, 0),
+ /* Data[1].ctlEdges[7].bChannel */ FREQ2FBIN(5825, 0)
+ },
+
+ {
+ /* Data[2].ctlEdges[0].bChannel */ FREQ2FBIN(5190, 0),
+ /* Data[2].ctlEdges[1].bChannel */ FREQ2FBIN(5230, 0),
+ /* Data[2].ctlEdges[2].bChannel */ FREQ2FBIN(5270, 0),
+ /* Data[2].ctlEdges[3].bChannel */ FREQ2FBIN(5310, 0),
+ /* Data[2].ctlEdges[4].bChannel */ FREQ2FBIN(5510, 0),
+ /* Data[2].ctlEdges[5].bChannel */ FREQ2FBIN(5550, 0),
+ /* Data[2].ctlEdges[6].bChannel */ FREQ2FBIN(5670, 0),
+ /* Data[2].ctlEdges[7].bChannel */ FREQ2FBIN(5755, 0)
+ },
+
+ {
+ /* Data[3].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[3].ctlEdges[1].bChannel */ FREQ2FBIN(5200, 0),
+ /* Data[3].ctlEdges[2].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[3].ctlEdges[3].bChannel */ FREQ2FBIN(5320, 0),
+ /* Data[3].ctlEdges[4].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[3].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[3].ctlEdges[6].bChannel */ 0xFF,
+ /* Data[3].ctlEdges[7].bChannel */ 0xFF,
+ },
+
+ {
+ /* Data[4].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[4].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[4].ctlEdges[2].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[4].ctlEdges[3].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[4].ctlEdges[4].bChannel */ 0xFF,
+ /* Data[4].ctlEdges[5].bChannel */ 0xFF,
+ /* Data[4].ctlEdges[6].bChannel */ 0xFF,
+ /* Data[4].ctlEdges[7].bChannel */ 0xFF,
+ },
+
+ {
+ /* Data[5].ctlEdges[0].bChannel */ FREQ2FBIN(5190, 0),
+ /* Data[5].ctlEdges[1].bChannel */ FREQ2FBIN(5270, 0),
+ /* Data[5].ctlEdges[2].bChannel */ FREQ2FBIN(5310, 0),
+ /* Data[5].ctlEdges[3].bChannel */ FREQ2FBIN(5510, 0),
+ /* Data[5].ctlEdges[4].bChannel */ FREQ2FBIN(5590, 0),
+ /* Data[5].ctlEdges[5].bChannel */ FREQ2FBIN(5670, 0),
+ /* Data[5].ctlEdges[6].bChannel */ 0xFF,
+ /* Data[5].ctlEdges[7].bChannel */ 0xFF
+ },
+
+ {
+ /* Data[6].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[6].ctlEdges[1].bChannel */ FREQ2FBIN(5200, 0),
+ /* Data[6].ctlEdges[2].bChannel */ FREQ2FBIN(5220, 0),
+ /* Data[6].ctlEdges[3].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[6].ctlEdges[4].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[6].ctlEdges[5].bChannel */ FREQ2FBIN(5600, 0),
+ /* Data[6].ctlEdges[6].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[6].ctlEdges[7].bChannel */ FREQ2FBIN(5745, 0)
+ },
+
+ {
+ /* Data[7].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[7].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[7].ctlEdges[2].bChannel */ FREQ2FBIN(5320, 0),
+ /* Data[7].ctlEdges[3].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[7].ctlEdges[4].bChannel */ FREQ2FBIN(5560, 0),
+ /* Data[7].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[7].ctlEdges[6].bChannel */ FREQ2FBIN(5745, 0),
+ /* Data[7].ctlEdges[7].bChannel */ FREQ2FBIN(5825, 0)
+ },
+
+ {
+ /* Data[8].ctlEdges[0].bChannel */ FREQ2FBIN(5190, 0),
+ /* Data[8].ctlEdges[1].bChannel */ FREQ2FBIN(5230, 0),
+ /* Data[8].ctlEdges[2].bChannel */ FREQ2FBIN(5270, 0),
+ /* Data[8].ctlEdges[3].bChannel */ FREQ2FBIN(5510, 0),
+ /* Data[8].ctlEdges[4].bChannel */ FREQ2FBIN(5550, 0),
+ /* Data[8].ctlEdges[5].bChannel */ FREQ2FBIN(5670, 0),
+ /* Data[8].ctlEdges[6].bChannel */ FREQ2FBIN(5755, 0),
+ /* Data[8].ctlEdges[7].bChannel */ FREQ2FBIN(5795, 0)
+ }
+ },
+ .ctlPowerData_5G = {
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 0}, {60, 1}, {60, 0}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ }
+ },
+ {
+ {
+ {60, 0}, {60, 1}, {60, 1}, {60, 0},
+ {60, 1}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ {60, 0}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 0}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 0}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 0}, {60, 1},
+ }
+ },
+ }
+ };
+
+
+ static const struct ar9300_eeprom ar9300_h112 = {
+ .eepromVersion = 2,
+ .templateVersion = 3,
+ .macAddr = {0x00, 0x03, 0x7f, 0x0, 0x0, 0x0},
+ .custData = {"h112-241-f0000"},
+ .baseEepHeader = {
+ .regDmn = { LE16(0), LE16(0x1f) },
+ .txrxMask = 0x77, /* 4 bits tx and 4 bits rx */
+ .opCapFlags = {
+ .opFlags = AR9300_OPFLAGS_11G | AR9300_OPFLAGS_11A,
+ .eepMisc = 0,
+ },
+ .rfSilent = 0,
+ .blueToothOptions = 0,
+ .deviceCap = 0,
+ .deviceType = 5, /* takes lower byte in eeprom location */
+ .pwrTableOffset = AR9300_PWR_TABLE_OFFSET,
+ .params_for_tuning_caps = {0, 0},
+ .featureEnable = 0x0d,
+ /*
+ * bit0 - enable tx temp comp - disabled
+ * bit1 - enable tx volt comp - disabled
+ * bit2 - enable fastClock - enabled
+ * bit3 - enable doubling - enabled
+ * bit4 - enable internal regulator - disabled
+ * bit5 - enable pa predistortion - disabled
+ */
+ .miscConfiguration = 0, /* bit0 - turn down drivestrength */
+ .eepromWriteEnableGpio = 6,
+ .wlanDisableGpio = 0,
+ .wlanLedGpio = 8,
+ .rxBandSelectGpio = 0xff,
+ .txrxgain = 0x10,
+ .swreg = 0,
+ },
+ .modalHeader2G = {
+ /* ar9300_modal_eep_header 2g */
+ /* 4 idle,t1,t2,b(4 bits per setting) */
+ .antCtrlCommon = LE32(0x110),
+ /* 4 ra1l1, ra2l1, ra1l2, ra2l2, ra12 */
+ .antCtrlCommon2 = LE32(0x44444),
+
+ /*
+ * antCtrlChain[AR9300_MAX_CHAINS]; 6 idle, t, r,
+ * rx1, rx12, b (2 bits each)
+ */
+ .antCtrlChain = { LE16(0x150), LE16(0x150), LE16(0x150) },
+
+ /*
+ * xatten1DB[AR9300_MAX_CHAINS]; 3 xatten1_db
+ * for ar9280 (0xa20c/b20c 5:0)
+ */
+ .xatten1DB = {0, 0, 0},
+
+ /*
+ * xatten1Margin[AR9300_MAX_CHAINS]; 3 xatten1_margin
+ * for ar9280 (0xa20c/b20c 16:12
+ */
+ .xatten1Margin = {0, 0, 0},
+ .tempSlope = 25,
+ .voltSlope = 0,
+
+ /*
+ * spurChans[OSPREY_EEPROM_MODAL_SPURS]; spur
+ * channels in usual fbin coding format
+ */
+ .spurChans = {FREQ2FBIN(2464, 1), 0, 0, 0, 0},
+
+ /*
+ * noiseFloorThreshCh[AR9300_MAX_CHAINS]; 3 Check
+ * if the register is per chain
+ */
+ .noiseFloorThreshCh = {-1, 0, 0},
+ .ob = {1, 1, 1},/* 3 chain */
+ .db_stage2 = {1, 1, 1}, /* 3 chain */
+ .db_stage3 = {0, 0, 0},
+ .db_stage4 = {0, 0, 0},
+ .xpaBiasLvl = 0,
+ .txFrameToDataStart = 0x0e,
+ .txFrameToPaOn = 0x0e,
+ .txClip = 3, /* 4 bits tx_clip, 4 bits dac_scale_cck */
+ .antennaGain = 0,
+ .switchSettling = 0x2c,
+ .adcDesiredSize = -30,
+ .txEndToXpaOff = 0,
+ .txEndToRxOn = 0x2,
+ .txFrameToXpaOn = 0xe,
+ .thresh62 = 28,
+ .papdRateMaskHt20 = LE32(0x80c080),
+ .papdRateMaskHt40 = LE32(0x80c080),
+ .futureModal = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ },
+ },
+ .base_ext1 = {
+ .ant_div_control = 0,
+ .future = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}
+ },
+ .calFreqPier2G = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1),
+ },
+ /* ar9300_cal_data_per_freq_op_loop 2g */
+ .calPierData2G = {
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ },
+ .calTarget_freqbin_Cck = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2484, 1),
+ },
+ .calTarget_freqbin_2G = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTarget_freqbin_2GHT20 = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTarget_freqbin_2GHT40 = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTargetPowerCck = {
+ /* 1L-5L,5S,11L,11S */
+ { {34, 34, 34, 34} },
+ { {34, 34, 34, 34} },
+ },
+ .calTargetPower2G = {
+ /* 6-24,36,48,54 */
+ { {34, 34, 32, 32} },
+ { {34, 34, 32, 32} },
+ { {34, 34, 32, 32} },
+ },
+ .calTargetPower2GHT20 = {
+ { {32, 32, 32, 32, 32, 30, 32, 32, 30, 28, 28, 28, 28, 24} },
+ { {32, 32, 32, 32, 32, 30, 32, 32, 30, 28, 28, 28, 28, 24} },
+ { {32, 32, 32, 32, 32, 30, 32, 32, 30, 28, 28, 28, 28, 24} },
+ },
+ .calTargetPower2GHT40 = {
+ { {30, 30, 30, 30, 30, 28, 30, 30, 28, 26, 26, 26, 26, 22} },
+ { {30, 30, 30, 30, 30, 28, 30, 30, 28, 26, 26, 26, 26, 22} },
+ { {30, 30, 30, 30, 30, 28, 30, 30, 28, 26, 26, 26, 26, 22} },
+ },
+ .ctlIndex_2G = {
+ 0x11, 0x12, 0x15, 0x17, 0x41, 0x42,
+ 0x45, 0x47, 0x31, 0x32, 0x35, 0x37,
+ },
+ .ctl_freqbin_2G = {
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2457, 1),
+ FREQ2FBIN(2462, 1)
+ },
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2462, 1),
+ 0xFF,
+ },
+
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2462, 1),
+ 0xFF,
+ },
+ {
+ FREQ2FBIN(2422, 1),
+ FREQ2FBIN(2427, 1),
+ FREQ2FBIN(2447, 1),
+ FREQ2FBIN(2452, 1)
+ },
+
+ {
+ /* Data[4].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[4].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[4].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ /* Data[4].ctlEdges[3].bChannel */ FREQ2FBIN(2484, 1),
+ },
+
+ {
+ /* Data[5].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[5].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[5].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ 0,
+ },
+
+ {
+ /* Data[6].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[6].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2472, 1),
+ 0,
+ },
+
+ {
+ /* Data[7].ctlEdges[0].bChannel */ FREQ2FBIN(2422, 1),
+ /* Data[7].ctlEdges[1].bChannel */ FREQ2FBIN(2427, 1),
+ /* Data[7].ctlEdges[2].bChannel */ FREQ2FBIN(2447, 1),
+ /* Data[7].ctlEdges[3].bChannel */ FREQ2FBIN(2462, 1),
+ },
+
+ {
+ /* Data[8].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[8].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[8].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ },
+
+ {
+ /* Data[9].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[9].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[9].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ 0
+ },
+
+ {
+ /* Data[10].ctlEdges[0].bChannel */ FREQ2FBIN(2412, 1),
+ /* Data[10].ctlEdges[1].bChannel */ FREQ2FBIN(2417, 1),
+ /* Data[10].ctlEdges[2].bChannel */ FREQ2FBIN(2472, 1),
+ 0
+ },
+
+ {
+ /* Data[11].ctlEdges[0].bChannel */ FREQ2FBIN(2422, 1),
+ /* Data[11].ctlEdges[1].bChannel */ FREQ2FBIN(2427, 1),
+ /* Data[11].ctlEdges[2].bChannel */ FREQ2FBIN(2447, 1),
+ /* Data[11].ctlEdges[3].bChannel */ FREQ2FBIN(2462, 1),
+ }
+ },
+ .ctlPowerData_2G = {
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 1}, {60, 0}, {60, 0}, {60, 1} } },
+
+ { { {60, 1}, {60, 0}, {0, 0}, {0, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 1} } },
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 1} } },
+ },
+ .modalHeader5G = {
+ /* 4 idle,t1,t2,b (4 bits per setting) */
+ .antCtrlCommon = LE32(0x220),
+ /* 4 ra1l1, ra2l1, ra1l2,ra2l2,ra12 */
+ .antCtrlCommon2 = LE32(0x44444),
+ /* antCtrlChain 6 idle, t,r,rx1,rx12,b (2 bits each) */
+ .antCtrlChain = {
+ LE16(0x150), LE16(0x150), LE16(0x150),
+ },
+ /* xatten1DB 3 xatten1_db for AR9280 (0xa20c/b20c 5:0) */
+ .xatten1DB = {0, 0, 0},
+
+ /*
+ * xatten1Margin[AR9300_MAX_CHAINS]; 3 xatten1_margin
+ * for merlin (0xa20c/b20c 16:12
+ */
+ .xatten1Margin = {0, 0, 0},
+ .tempSlope = 45,
+ .voltSlope = 0,
+ /* spurChans spur channels in usual fbin coding format */
+ .spurChans = {0, 0, 0, 0, 0},
+ /* noiseFloorThreshCh Check if the register is per chain */
+ .noiseFloorThreshCh = {-1, 0, 0},
+ .ob = {3, 3, 3}, /* 3 chain */
+ .db_stage2 = {3, 3, 3}, /* 3 chain */
+ .db_stage3 = {3, 3, 3}, /* doesn't exist for 2G */
+ .db_stage4 = {3, 3, 3}, /* don't exist for 2G */
+ .xpaBiasLvl = 0,
+ .txFrameToDataStart = 0x0e,
+ .txFrameToPaOn = 0x0e,
+ .txClip = 3, /* 4 bits tx_clip, 4 bits dac_scale_cck */
+ .antennaGain = 0,
+ .switchSettling = 0x2d,
+ .adcDesiredSize = -30,
+ .txEndToXpaOff = 0,
+ .txEndToRxOn = 0x2,
+ .txFrameToXpaOn = 0xe,
+ .thresh62 = 28,
+ .papdRateMaskHt20 = LE32(0x0cf0e0e0),
+ .papdRateMaskHt40 = LE32(0x6cf0e0e0),
+ .futureModal = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ },
+ },
+ .base_ext2 = {
+ .tempSlopeLow = 40,
+ .tempSlopeHigh = 50,
+ .xatten1DBLow = {0, 0, 0},
+ .xatten1MarginLow = {0, 0, 0},
+ .xatten1DBHigh = {0, 0, 0},
+ .xatten1MarginHigh = {0, 0, 0}
+ },
+ .calFreqPier5G = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5220, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5700, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calPierData5G = {
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+
+ },
+ .calTarget_freqbin_5G = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5240, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5700, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTarget_freqbin_5GHT20 = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5240, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5700, 0),
+ FREQ2FBIN(5745, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTarget_freqbin_5GHT40 = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5240, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5700, 0),
+ FREQ2FBIN(5745, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTargetPower5G = {
+ /* 6-24,36,48,54 */
+ { {30, 30, 28, 24} },
+ { {30, 30, 28, 24} },
+ { {30, 30, 28, 24} },
+ { {30, 30, 28, 24} },
+ { {30, 30, 28, 24} },
+ { {30, 30, 28, 24} },
+ { {30, 30, 28, 24} },
+ { {30, 30, 28, 24} },
+ },
+ .calTargetPower5GHT20 = {
+ /*
+ * 0_8_16,1-3_9-11_17-19,
+ * 4,5,6,7,12,13,14,15,20,21,22,23
+ */
+ { {30, 30, 30, 28, 24, 20, 30, 28, 24, 20, 20, 20, 20, 16} },
+ { {30, 30, 30, 28, 24, 20, 30, 28, 24, 20, 20, 20, 20, 16} },
+ { {30, 30, 30, 26, 22, 18, 30, 26, 22, 18, 18, 18, 18, 16} },
+ { {30, 30, 30, 26, 22, 18, 30, 26, 22, 18, 18, 18, 18, 16} },
+ { {30, 30, 30, 24, 20, 16, 30, 24, 20, 16, 16, 16, 16, 14} },
+ { {30, 30, 30, 24, 20, 16, 30, 24, 20, 16, 16, 16, 16, 14} },
+ { {30, 30, 30, 22, 18, 14, 30, 22, 18, 14, 14, 14, 14, 12} },
+ { {30, 30, 30, 22, 18, 14, 30, 22, 18, 14, 14, 14, 14, 12} },
+ },
+ .calTargetPower5GHT40 = {
+ /*
+ * 0_8_16,1-3_9-11_17-19,
+ * 4,5,6,7,12,13,14,15,20,21,22,23
+ */
+ { {28, 28, 28, 26, 22, 18, 28, 26, 22, 18, 18, 18, 18, 14} },
+ { {28, 28, 28, 26, 22, 18, 28, 26, 22, 18, 18, 18, 18, 14} },
+ { {28, 28, 28, 24, 20, 16, 28, 24, 20, 16, 16, 16, 16, 12} },
+ { {28, 28, 28, 24, 20, 16, 28, 24, 20, 16, 16, 16, 16, 12} },
+ { {28, 28, 28, 22, 18, 14, 28, 22, 18, 14, 14, 14, 14, 10} },
+ { {28, 28, 28, 22, 18, 14, 28, 22, 18, 14, 14, 14, 14, 10} },
+ { {28, 28, 28, 20, 16, 12, 28, 20, 16, 12, 12, 12, 12, 8} },
+ { {28, 28, 28, 20, 16, 12, 28, 20, 16, 12, 12, 12, 12, 8} },
+ },
+ .ctlIndex_5G = {
+ 0x10, 0x16, 0x18, 0x40, 0x46,
+ 0x48, 0x30, 0x36, 0x38
+ },
+ .ctl_freqbin_5G = {
+ {
+ /* Data[0].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[0].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[0].ctlEdges[2].bChannel */ FREQ2FBIN(5280, 0),
+ /* Data[0].ctlEdges[3].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[0].ctlEdges[4].bChannel */ FREQ2FBIN(5600, 0),
+ /* Data[0].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[0].ctlEdges[6].bChannel */ FREQ2FBIN(5745, 0),
+ /* Data[0].ctlEdges[7].bChannel */ FREQ2FBIN(5825, 0)
+ },
+ {
+ /* Data[1].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[1].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[1].ctlEdges[2].bChannel */ FREQ2FBIN(5280, 0),
+ /* Data[1].ctlEdges[3].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[1].ctlEdges[4].bChannel */ FREQ2FBIN(5520, 0),
+ /* Data[1].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[1].ctlEdges[6].bChannel */ FREQ2FBIN(5745, 0),
+ /* Data[1].ctlEdges[7].bChannel */ FREQ2FBIN(5825, 0)
+ },
+
+ {
+ /* Data[2].ctlEdges[0].bChannel */ FREQ2FBIN(5190, 0),
+ /* Data[2].ctlEdges[1].bChannel */ FREQ2FBIN(5230, 0),
+ /* Data[2].ctlEdges[2].bChannel */ FREQ2FBIN(5270, 0),
+ /* Data[2].ctlEdges[3].bChannel */ FREQ2FBIN(5310, 0),
+ /* Data[2].ctlEdges[4].bChannel */ FREQ2FBIN(5510, 0),
+ /* Data[2].ctlEdges[5].bChannel */ FREQ2FBIN(5550, 0),
+ /* Data[2].ctlEdges[6].bChannel */ FREQ2FBIN(5670, 0),
+ /* Data[2].ctlEdges[7].bChannel */ FREQ2FBIN(5755, 0)
+ },
+
+ {
+ /* Data[3].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[3].ctlEdges[1].bChannel */ FREQ2FBIN(5200, 0),
+ /* Data[3].ctlEdges[2].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[3].ctlEdges[3].bChannel */ FREQ2FBIN(5320, 0),
+ /* Data[3].ctlEdges[4].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[3].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[3].ctlEdges[6].bChannel */ 0xFF,
+ /* Data[3].ctlEdges[7].bChannel */ 0xFF,
+ },
+
+ {
+ /* Data[4].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[4].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[4].ctlEdges[2].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[4].ctlEdges[3].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[4].ctlEdges[4].bChannel */ 0xFF,
+ /* Data[4].ctlEdges[5].bChannel */ 0xFF,
+ /* Data[4].ctlEdges[6].bChannel */ 0xFF,
+ /* Data[4].ctlEdges[7].bChannel */ 0xFF,
+ },
+
+ {
+ /* Data[5].ctlEdges[0].bChannel */ FREQ2FBIN(5190, 0),
+ /* Data[5].ctlEdges[1].bChannel */ FREQ2FBIN(5270, 0),
+ /* Data[5].ctlEdges[2].bChannel */ FREQ2FBIN(5310, 0),
+ /* Data[5].ctlEdges[3].bChannel */ FREQ2FBIN(5510, 0),
+ /* Data[5].ctlEdges[4].bChannel */ FREQ2FBIN(5590, 0),
+ /* Data[5].ctlEdges[5].bChannel */ FREQ2FBIN(5670, 0),
+ /* Data[5].ctlEdges[6].bChannel */ 0xFF,
+ /* Data[5].ctlEdges[7].bChannel */ 0xFF
+ },
+
+ {
+ /* Data[6].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[6].ctlEdges[1].bChannel */ FREQ2FBIN(5200, 0),
+ /* Data[6].ctlEdges[2].bChannel */ FREQ2FBIN(5220, 0),
+ /* Data[6].ctlEdges[3].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[6].ctlEdges[4].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[6].ctlEdges[5].bChannel */ FREQ2FBIN(5600, 0),
+ /* Data[6].ctlEdges[6].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[6].ctlEdges[7].bChannel */ FREQ2FBIN(5745, 0)
+ },
+
+ {
+ /* Data[7].ctlEdges[0].bChannel */ FREQ2FBIN(5180, 0),
+ /* Data[7].ctlEdges[1].bChannel */ FREQ2FBIN(5260, 0),
+ /* Data[7].ctlEdges[2].bChannel */ FREQ2FBIN(5320, 0),
+ /* Data[7].ctlEdges[3].bChannel */ FREQ2FBIN(5500, 0),
+ /* Data[7].ctlEdges[4].bChannel */ FREQ2FBIN(5560, 0),
+ /* Data[7].ctlEdges[5].bChannel */ FREQ2FBIN(5700, 0),
+ /* Data[7].ctlEdges[6].bChannel */ FREQ2FBIN(5745, 0),
+ /* Data[7].ctlEdges[7].bChannel */ FREQ2FBIN(5825, 0)
+ },
+
+ {
+ /* Data[8].ctlEdges[0].bChannel */ FREQ2FBIN(5190, 0),
+ /* Data[8].ctlEdges[1].bChannel */ FREQ2FBIN(5230, 0),
+ /* Data[8].ctlEdges[2].bChannel */ FREQ2FBIN(5270, 0),
+ /* Data[8].ctlEdges[3].bChannel */ FREQ2FBIN(5510, 0),
+ /* Data[8].ctlEdges[4].bChannel */ FREQ2FBIN(5550, 0),
+ /* Data[8].ctlEdges[5].bChannel */ FREQ2FBIN(5670, 0),
+ /* Data[8].ctlEdges[6].bChannel */ FREQ2FBIN(5755, 0),
+ /* Data[8].ctlEdges[7].bChannel */ FREQ2FBIN(5795, 0)
+ }
+ },
+ .ctlPowerData_5G = {
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 0}, {60, 1}, {60, 0}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ }
+ },
+ {
+ {
+ {60, 0}, {60, 1}, {60, 1}, {60, 0},
+ {60, 1}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ {60, 0}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 0}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 0}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 0}, {60, 1},
+ }
+ },
+ }
+ };
+
+
+ static const struct ar9300_eeprom ar9300_x112 = {
+ .eepromVersion = 2,
+ .templateVersion = 5,
+ .macAddr = {0x00, 0x03, 0x7f, 0x0, 0x0, 0x0},
+ .custData = {"x112-041-f0000"},
+ .baseEepHeader = {
+ .regDmn = { LE16(0), LE16(0x1f) },
+ .txrxMask = 0x77, /* 4 bits tx and 4 bits rx */
+ .opCapFlags = {
+ .opFlags = AR9300_OPFLAGS_11G | AR9300_OPFLAGS_11A,
+ .eepMisc = 0,
+ },
+ .rfSilent = 0,
+ .blueToothOptions = 0,
+ .deviceCap = 0,
+ .deviceType = 5, /* takes lower byte in eeprom location */
+ .pwrTableOffset = AR9300_PWR_TABLE_OFFSET,
+ .params_for_tuning_caps = {0, 0},
+ .featureEnable = 0x0d,
+ /*
+ * bit0 - enable tx temp comp - disabled
+ * bit1 - enable tx volt comp - disabled
+ * bit2 - enable fastclock - enabled
+ * bit3 - enable doubling - enabled
+ * bit4 - enable internal regulator - disabled
+ * bit5 - enable pa predistortion - disabled
+ */
+ .miscConfiguration = 0, /* bit0 - turn down drivestrength */
+ .eepromWriteEnableGpio = 6,
+ .wlanDisableGpio = 0,
+ .wlanLedGpio = 8,
+ .rxBandSelectGpio = 0xff,
+ .txrxgain = 0x0,
+ .swreg = 0,
+ },
+ .modalHeader2G = {
+ /* ar9300_modal_eep_header 2g */
+ /* 4 idle,t1,t2,b(4 bits per setting) */
+ .antCtrlCommon = LE32(0x110),
+ /* 4 ra1l1, ra2l1, ra1l2, ra2l2, ra12 */
+ .antCtrlCommon2 = LE32(0x22222),
+
+ /*
+ * antCtrlChain[ar9300_max_chains]; 6 idle, t, r,
+ * rx1, rx12, b (2 bits each)
+ */
+ .antCtrlChain = { LE16(0x10), LE16(0x10), LE16(0x10) },
+
+ /*
+ * xatten1DB[AR9300_max_chains]; 3 xatten1_db
+ * for ar9280 (0xa20c/b20c 5:0)
+ */
+ .xatten1DB = {0x1b, 0x1b, 0x1b},
+
+ /*
+ * xatten1Margin[ar9300_max_chains]; 3 xatten1_margin
+ * for ar9280 (0xa20c/b20c 16:12
+ */
+ .xatten1Margin = {0x15, 0x15, 0x15},
+ .tempSlope = 50,
+ .voltSlope = 0,
+
+ /*
+ * spurChans[OSPrey_eeprom_modal_sPURS]; spur
+ * channels in usual fbin coding format
+ */
+ .spurChans = {FREQ2FBIN(2464, 1), 0, 0, 0, 0},
+
+ /*
+ * noiseFloorThreshch[ar9300_max_cHAINS]; 3 Check
+ * if the register is per chain
+ */
+ .noiseFloorThreshCh = {-1, 0, 0},
+ .ob = {1, 1, 1},/* 3 chain */
+ .db_stage2 = {1, 1, 1}, /* 3 chain */
+ .db_stage3 = {0, 0, 0},
+ .db_stage4 = {0, 0, 0},
+ .xpaBiasLvl = 0,
+ .txFrameToDataStart = 0x0e,
+ .txFrameToPaOn = 0x0e,
+ .txClip = 3, /* 4 bits tx_clip, 4 bits dac_scale_cck */
+ .antennaGain = 0,
+ .switchSettling = 0x2c,
+ .adcDesiredSize = -30,
+ .txEndToXpaOff = 0,
+ .txEndToRxOn = 0x2,
+ .txFrameToXpaOn = 0xe,
+ .thresh62 = 28,
+ .papdRateMaskHt20 = LE32(0x0c80c080),
+ .papdRateMaskHt40 = LE32(0x0080c080),
+ .futureModal = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ },
+ },
+ .base_ext1 = {
+ .ant_div_control = 0,
+ .future = {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0}
+ },
+ .calFreqPier2G = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1),
+ },
+ /* ar9300_cal_data_per_freq_op_loop 2g */
+ .calPierData2G = {
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ { {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0}, {0, 0, 0, 0, 0, 0} },
+ },
+ .calTarget_freqbin_Cck = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2472, 1),
+ },
+ .calTarget_freqbin_2G = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTarget_freqbin_2GHT20 = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTarget_freqbin_2GHT40 = {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2437, 1),
+ FREQ2FBIN(2472, 1)
+ },
+ .calTargetPowerCck = {
+ /* 1L-5L,5S,11L,11s */
+ { {38, 38, 38, 38} },
+ { {38, 38, 38, 38} },
+ },
+ .calTargetPower2G = {
+ /* 6-24,36,48,54 */
+ { {38, 38, 36, 34} },
+ { {38, 38, 36, 34} },
+ { {38, 38, 34, 32} },
+ },
+ .calTargetPower2GHT20 = {
+ { {36, 36, 36, 36, 36, 34, 34, 32, 30, 28, 28, 28, 28, 26} },
+ { {36, 36, 36, 36, 36, 34, 36, 34, 32, 30, 30, 30, 28, 26} },
+ { {36, 36, 36, 36, 36, 34, 34, 32, 30, 28, 28, 28, 28, 26} },
+ },
+ .calTargetPower2GHT40 = {
+ { {36, 36, 36, 36, 34, 32, 32, 30, 28, 26, 26, 26, 26, 24} },
+ { {36, 36, 36, 36, 34, 32, 34, 32, 30, 28, 28, 28, 28, 24} },
+ { {36, 36, 36, 36, 34, 32, 32, 30, 28, 26, 26, 26, 26, 24} },
+ },
+ .ctlIndex_2G = {
+ 0x11, 0x12, 0x15, 0x17, 0x41, 0x42,
+ 0x45, 0x47, 0x31, 0x32, 0x35, 0x37,
+ },
+ .ctl_freqbin_2G = {
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2457, 1),
+ FREQ2FBIN(2462, 1)
+ },
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2462, 1),
+ 0xFF,
+ },
+
+ {
+ FREQ2FBIN(2412, 1),
+ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2462, 1),
+ 0xFF,
+ },
+ {
+ FREQ2FBIN(2422, 1),
+ FREQ2FBIN(2427, 1),
+ FREQ2FBIN(2447, 1),
+ FREQ2FBIN(2452, 1)
+ },
+
+ {
+ /* Data[4].ctledges[0].bchannel */ FREQ2FBIN(2412, 1),
+ /* Data[4].ctledges[1].bchannel */ FREQ2FBIN(2417, 1),
+ /* Data[4].ctledges[2].bchannel */ FREQ2FBIN(2472, 1),
+ /* Data[4].ctledges[3].bchannel */ FREQ2FBIN(2484, 1),
+ },
+
+ {
+ /* Data[5].ctledges[0].bchannel */ FREQ2FBIN(2412, 1),
+ /* Data[5].ctledges[1].bchannel */ FREQ2FBIN(2417, 1),
+ /* Data[5].ctledges[2].bchannel */ FREQ2FBIN(2472, 1),
+ 0,
+ },
+
+ {
+ /* Data[6].ctledges[0].bchannel */ FREQ2FBIN(2412, 1),
+ /* Data[6].ctledges[1].bchannel */ FREQ2FBIN(2417, 1),
+ FREQ2FBIN(2472, 1),
+ 0,
+ },
+
+ {
+ /* Data[7].ctledges[0].bchannel */ FREQ2FBIN(2422, 1),
+ /* Data[7].ctledges[1].bchannel */ FREQ2FBIN(2427, 1),
+ /* Data[7].ctledges[2].bchannel */ FREQ2FBIN(2447, 1),
+ /* Data[7].ctledges[3].bchannel */ FREQ2FBIN(2462, 1),
+ },
+
+ {
+ /* Data[8].ctledges[0].bchannel */ FREQ2FBIN(2412, 1),
+ /* Data[8].ctledges[1].bchannel */ FREQ2FBIN(2417, 1),
+ /* Data[8].ctledges[2].bchannel */ FREQ2FBIN(2472, 1),
+ },
+
+ {
+ /* Data[9].ctledges[0].bchannel */ FREQ2FBIN(2412, 1),
+ /* Data[9].ctledges[1].bchannel */ FREQ2FBIN(2417, 1),
+ /* Data[9].ctledges[2].bchannel */ FREQ2FBIN(2472, 1),
+ 0
+ },
+
+ {
+ /* Data[10].ctledges[0].bchannel */ FREQ2FBIN(2412, 1),
+ /* Data[10].ctledges[1].bchannel */ FREQ2FBIN(2417, 1),
+ /* Data[10].ctledges[2].bchannel */ FREQ2FBIN(2472, 1),
+ 0
+ },
+
+ {
+ /* Data[11].ctledges[0].bchannel */ FREQ2FBIN(2422, 1),
+ /* Data[11].ctledges[1].bchannel */ FREQ2FBIN(2427, 1),
+ /* Data[11].ctledges[2].bchannel */ FREQ2FBIN(2447, 1),
+ /* Data[11].ctledges[3].bchannel */ FREQ2FBIN(2462, 1),
+ }
+ },
+ .ctlPowerData_2G = {
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 1}, {60, 0}, {60, 0}, {60, 1} } },
+
+ { { {60, 1}, {60, 0}, {0, 0}, {0, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+
+ { { {60, 0}, {60, 1}, {60, 0}, {60, 0} } },
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 1} } },
+ { { {60, 0}, {60, 1}, {60, 1}, {60, 1} } },
+ },
+ .modalHeader5G = {
+ /* 4 idle,t1,t2,b (4 bits per setting) */
+ .antCtrlCommon = LE32(0x110),
+ /* 4 ra1l1, ra2l1, ra1l2,ra2l2,ra12 */
+ .antCtrlCommon2 = LE32(0x22222),
+ /* antCtrlChain 6 idle, t,r,rx1,rx12,b (2 bits each) */
+ .antCtrlChain = {
+ LE16(0x0), LE16(0x0), LE16(0x0),
+ },
+ /* xatten1DB 3 xatten1_db for ar9280 (0xa20c/b20c 5:0) */
+ .xatten1DB = {0x13, 0x19, 0x17},
+
+ /*
+ * xatten1Margin[ar9300_max_chains]; 3 xatten1_margin
+ * for merlin (0xa20c/b20c 16:12
+ */
+ .xatten1Margin = {0x19, 0x19, 0x19},
+ .tempSlope = 70,
+ .voltSlope = 15,
+ /* spurChans spur channels in usual fbin coding format */
+ .spurChans = {0, 0, 0, 0, 0},
+ /* noiseFloorThreshch check if the register is per chain */
+ .noiseFloorThreshCh = {-1, 0, 0},
+ .ob = {3, 3, 3}, /* 3 chain */
+ .db_stage2 = {3, 3, 3}, /* 3 chain */
+ .db_stage3 = {3, 3, 3}, /* doesn't exist for 2G */
+ .db_stage4 = {3, 3, 3}, /* don't exist for 2G */
+ .xpaBiasLvl = 0,
+ .txFrameToDataStart = 0x0e,
+ .txFrameToPaOn = 0x0e,
+ .txClip = 3, /* 4 bits tx_clip, 4 bits dac_scale_cck */
+ .antennaGain = 0,
+ .switchSettling = 0x2d,
+ .adcDesiredSize = -30,
+ .txEndToXpaOff = 0,
+ .txEndToRxOn = 0x2,
+ .txFrameToXpaOn = 0xe,
+ .thresh62 = 28,
+ .papdRateMaskHt20 = LE32(0x0cf0e0e0),
+ .papdRateMaskHt40 = LE32(0x6cf0e0e0),
+ .futureModal = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+ },
+ },
+ .base_ext2 = {
+ .tempSlopeLow = 72,
+ .tempSlopeHigh = 105,
+ .xatten1DBLow = {0x10, 0x14, 0x10},
+ .xatten1MarginLow = {0x19, 0x19 , 0x19},
+ .xatten1DBHigh = {0x1d, 0x20, 0x24},
+ .xatten1MarginHigh = {0x10, 0x10, 0x10}
+ },
+ .calFreqPier5G = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5220, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5700, 0),
+ FREQ2FBIN(5785, 0)
+ },
+ .calPierData5G = {
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+ {
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ {0, 0, 0, 0, 0},
+ },
+
+ },
+ .calTarget_freqbin_5G = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5220, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5725, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTarget_freqbin_5GHT20 = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5220, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5725, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTarget_freqbin_5GHT40 = {
+ FREQ2FBIN(5180, 0),
+ FREQ2FBIN(5220, 0),
+ FREQ2FBIN(5320, 0),
+ FREQ2FBIN(5400, 0),
+ FREQ2FBIN(5500, 0),
+ FREQ2FBIN(5600, 0),
+ FREQ2FBIN(5725, 0),
+ FREQ2FBIN(5825, 0)
+ },
+ .calTargetPower5G = {
+ /* 6-24,36,48,54 */
+ { {32, 32, 28, 26} },
+ { {32, 32, 28, 26} },
+ { {32, 32, 28, 26} },
+ { {32, 32, 26, 24} },
+ { {32, 32, 26, 24} },
+ { {32, 32, 24, 22} },
+ { {30, 30, 24, 22} },
+ { {30, 30, 24, 22} },
+ },
+ .calTargetPower5GHT20 = {
+ /*
+ * 0_8_16,1-3_9-11_17-19,
+ * 4,5,6,7,12,13,14,15,20,21,22,23
+ */
+ { {32, 32, 32, 32, 28, 26, 32, 28, 26, 24, 24, 24, 22, 22} },
+ { {32, 32, 32, 32, 28, 26, 32, 28, 26, 24, 24, 24, 22, 22} },
+ { {32, 32, 32, 32, 28, 26, 32, 28, 26, 24, 24, 24, 22, 22} },
+ { {32, 32, 32, 32, 28, 26, 32, 26, 24, 22, 22, 22, 20, 20} },
+ { {32, 32, 32, 32, 28, 26, 32, 26, 24, 22, 20, 18, 16, 16} },
+ { {32, 32, 32, 32, 28, 26, 32, 24, 20, 16, 18, 16, 14, 14} },
+ { {30, 30, 30, 30, 28, 26, 30, 24, 20, 16, 18, 16, 14, 14} },
+ { {30, 30, 30, 30, 28, 26, 30, 24, 20, 16, 18, 16, 14, 14} },
+ },
+ .calTargetPower5GHT40 = {
+ /*
+ * 0_8_16,1-3_9-11_17-19,
+ * 4,5,6,7,12,13,14,15,20,21,22,23
+ */
+ { {32, 32, 32, 30, 28, 26, 30, 28, 26, 24, 24, 24, 22, 22} },
+ { {32, 32, 32, 30, 28, 26, 30, 28, 26, 24, 24, 24, 22, 22} },
+ { {32, 32, 32, 30, 28, 26, 30, 28, 26, 24, 24, 24, 22, 22} },
+ { {32, 32, 32, 30, 28, 26, 30, 26, 24, 22, 22, 22, 20, 20} },
+ { {32, 32, 32, 30, 28, 26, 30, 26, 24, 22, 20, 18, 16, 16} },
+ { {32, 32, 32, 30, 28, 26, 30, 22, 20, 16, 18, 16, 14, 14} },
+ { {30, 30, 30, 30, 28, 26, 30, 22, 20, 16, 18, 16, 14, 14} },
+ { {30, 30, 30, 30, 28, 26, 30, 22, 20, 16, 18, 16, 14, 14} },
+ },
+ .ctlIndex_5G = {
+ 0x10, 0x16, 0x18, 0x40, 0x46,
+ 0x48, 0x30, 0x36, 0x38
+ },
+ .ctl_freqbin_5G = {
+ {
+ /* Data[0].ctledges[0].bchannel */ FREQ2FBIN(5180, 0),
+ /* Data[0].ctledges[1].bchannel */ FREQ2FBIN(5260, 0),
+ /* Data[0].ctledges[2].bchannel */ FREQ2FBIN(5280, 0),
+ /* Data[0].ctledges[3].bchannel */ FREQ2FBIN(5500, 0),
+ /* Data[0].ctledges[4].bchannel */ FREQ2FBIN(5600, 0),
+ /* Data[0].ctledges[5].bchannel */ FREQ2FBIN(5700, 0),
+ /* Data[0].ctledges[6].bchannel */ FREQ2FBIN(5745, 0),
+ /* Data[0].ctledges[7].bchannel */ FREQ2FBIN(5825, 0)
+ },
+ {
+ /* Data[1].ctledges[0].bchannel */ FREQ2FBIN(5180, 0),
+ /* Data[1].ctledges[1].bchannel */ FREQ2FBIN(5260, 0),
+ /* Data[1].ctledges[2].bchannel */ FREQ2FBIN(5280, 0),
+ /* Data[1].ctledges[3].bchannel */ FREQ2FBIN(5500, 0),
+ /* Data[1].ctledges[4].bchannel */ FREQ2FBIN(5520, 0),
+ /* Data[1].ctledges[5].bchannel */ FREQ2FBIN(5700, 0),
+ /* Data[1].ctledges[6].bchannel */ FREQ2FBIN(5745, 0),
+ /* Data[1].ctledges[7].bchannel */ FREQ2FBIN(5825, 0)
+ },
+
+ {
+ /* Data[2].ctledges[0].bchannel */ FREQ2FBIN(5190, 0),
+ /* Data[2].ctledges[1].bchannel */ FREQ2FBIN(5230, 0),
+ /* Data[2].ctledges[2].bchannel */ FREQ2FBIN(5270, 0),
+ /* Data[2].ctledges[3].bchannel */ FREQ2FBIN(5310, 0),
+ /* Data[2].ctledges[4].bchannel */ FREQ2FBIN(5510, 0),
+ /* Data[2].ctledges[5].bchannel */ FREQ2FBIN(5550, 0),
+ /* Data[2].ctledges[6].bchannel */ FREQ2FBIN(5670, 0),
+ /* Data[2].ctledges[7].bchannel */ FREQ2FBIN(5755, 0)
+ },
+
+ {
+ /* Data[3].ctledges[0].bchannel */ FREQ2FBIN(5180, 0),
+ /* Data[3].ctledges[1].bchannel */ FREQ2FBIN(5200, 0),
+ /* Data[3].ctledges[2].bchannel */ FREQ2FBIN(5260, 0),
+ /* Data[3].ctledges[3].bchannel */ FREQ2FBIN(5320, 0),
+ /* Data[3].ctledges[4].bchannel */ FREQ2FBIN(5500, 0),
+ /* Data[3].ctledges[5].bchannel */ FREQ2FBIN(5700, 0),
+ /* Data[3].ctledges[6].bchannel */ 0xFF,
+ /* Data[3].ctledges[7].bchannel */ 0xFF,
+ },
+
+ {
+ /* Data[4].ctledges[0].bchannel */ FREQ2FBIN(5180, 0),
+ /* Data[4].ctledges[1].bchannel */ FREQ2FBIN(5260, 0),
+ /* Data[4].ctledges[2].bchannel */ FREQ2FBIN(5500, 0),
+ /* Data[4].ctledges[3].bchannel */ FREQ2FBIN(5700, 0),
+ /* Data[4].ctledges[4].bchannel */ 0xFF,
+ /* Data[4].ctledges[5].bchannel */ 0xFF,
+ /* Data[4].ctledges[6].bchannel */ 0xFF,
+ /* Data[4].ctledges[7].bchannel */ 0xFF,
+ },
+
+ {
+ /* Data[5].ctledges[0].bchannel */ FREQ2FBIN(5190, 0),
+ /* Data[5].ctledges[1].bchannel */ FREQ2FBIN(5270, 0),
+ /* Data[5].ctledges[2].bchannel */ FREQ2FBIN(5310, 0),
+ /* Data[5].ctledges[3].bchannel */ FREQ2FBIN(5510, 0),
+ /* Data[5].ctledges[4].bchannel */ FREQ2FBIN(5590, 0),
+ /* Data[5].ctledges[5].bchannel */ FREQ2FBIN(5670, 0),
+ /* Data[5].ctledges[6].bchannel */ 0xFF,
+ /* Data[5].ctledges[7].bchannel */ 0xFF
+ },
+
+ {
+ /* Data[6].ctledges[0].bchannel */ FREQ2FBIN(5180, 0),
+ /* Data[6].ctledges[1].bchannel */ FREQ2FBIN(5200, 0),
+ /* Data[6].ctledges[2].bchannel */ FREQ2FBIN(5220, 0),
+ /* Data[6].ctledges[3].bchannel */ FREQ2FBIN(5260, 0),
+ /* Data[6].ctledges[4].bchannel */ FREQ2FBIN(5500, 0),
+ /* Data[6].ctledges[5].bchannel */ FREQ2FBIN(5600, 0),
+ /* Data[6].ctledges[6].bchannel */ FREQ2FBIN(5700, 0),
+ /* Data[6].ctledges[7].bchannel */ FREQ2FBIN(5745, 0)
+ },
+
+ {
+ /* Data[7].ctledges[0].bchannel */ FREQ2FBIN(5180, 0),
+ /* Data[7].ctledges[1].bchannel */ FREQ2FBIN(5260, 0),
+ /* Data[7].ctledges[2].bchannel */ FREQ2FBIN(5320, 0),
+ /* Data[7].ctledges[3].bchannel */ FREQ2FBIN(5500, 0),
+ /* Data[7].ctledges[4].bchannel */ FREQ2FBIN(5560, 0),
+ /* Data[7].ctledges[5].bchannel */ FREQ2FBIN(5700, 0),
+ /* Data[7].ctledges[6].bchannel */ FREQ2FBIN(5745, 0),
+ /* Data[7].ctledges[7].bchannel */ FREQ2FBIN(5825, 0)
+ },
+
+ {
+ /* Data[8].ctledges[0].bchannel */ FREQ2FBIN(5190, 0),
+ /* Data[8].ctledges[1].bchannel */ FREQ2FBIN(5230, 0),
+ /* Data[8].ctledges[2].bchannel */ FREQ2FBIN(5270, 0),
+ /* Data[8].ctledges[3].bchannel */ FREQ2FBIN(5510, 0),
+ /* Data[8].ctledges[4].bchannel */ FREQ2FBIN(5550, 0),
+ /* Data[8].ctledges[5].bchannel */ FREQ2FBIN(5670, 0),
+ /* Data[8].ctledges[6].bchannel */ FREQ2FBIN(5755, 0),
+ /* Data[8].ctledges[7].bchannel */ FREQ2FBIN(5795, 0)
+ }
+ },
+ .ctlPowerData_5G = {
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 0}, {60, 1}, {60, 0}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ }
+ },
+ {
+ {
+ {60, 0}, {60, 1}, {60, 1}, {60, 0},
+ {60, 1}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ {60, 0}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 0}, {60, 0}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 1},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 1}, {60, 0}, {60, 1},
+ {60, 1}, {60, 1}, {60, 1}, {60, 0},
+ }
+ },
+ {
+ {
+ {60, 1}, {60, 0}, {60, 1}, {60, 1},
+ {60, 1}, {60, 1}, {60, 0}, {60, 1},
+ }
+ },
+ }
+ };
+
+ static const struct ar9300_eeprom ar9300_h116 = {
+ .eepromVersion = 2,
+ .templateVersion = 4,
+ .macAddr = {0x00, 0x03, 0x7f, 0x0, 0x0, 0x0},
+ .custData = {"h116-041-f0000"},
.baseEepHeader = {
.regDmn = { LE16(0), LE16(0x1f) },
- .txrxMask = 0x77, /* 4 bits tx and 4 bits rx */
+ .txrxMask = 0x33, /* 4 bits tx and 4 bits rx */
.opCapFlags = {
.opFlags = AR9300_OPFLAGS_11G | AR9300_OPFLAGS_11A,
.eepMisc = 0,
^ permalink raw reply
* Re: linux-next: unsigned commit ...
From: Casey Schaufler @ 2010-12-02 22:38 UTC (permalink / raw)
To: Stephen Rothwell; +Cc: James Morris, linux-next, Casey Schaufler
In-Reply-To: <20101203092928.367d45c0.sfr@canb.auug.org.au>
The problem was in my converting to a git based submission
process, not with the level of review, although I can see how
the two would be indistinguishable. Thank you for the follow-up.
On 12/2/2010 2:29 PM, Stephen Rothwell wrote:
> Hi James,
>
> Commit 676dac4b1bee0469d6932f698aeb77e8489f5861 ("This patch adds a new
> security attribute to Smack called") that was added to your tree today
> has no Signed-off-by and could do with a better summary line in the
> commit message. And probably a better explanation of what it does.
>
> Makes me wonder about the level of review it received :-(
>
^ permalink raw reply
* linux-next: unsigned commit ...
From: Stephen Rothwell @ 2010-12-02 22:29 UTC (permalink / raw)
To: James Morris; +Cc: linux-next, Casey Schaufler
[-- Attachment #1: Type: text/plain, Size: 466 bytes --]
Hi James,
Commit 676dac4b1bee0469d6932f698aeb77e8489f5861 ("This patch adds a new
security attribute to Smack called") that was added to your tree today
has no Signed-off-by and could do with a better summary line in the
commit message. And probably a better explanation of what it does.
Makes me wonder about the level of review it received :-(
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply
* Re: linux-next: Tree for November 19 (rtmutex)
From: Randy Dunlap @ 2010-12-02 19:52 UTC (permalink / raw)
To: LKML; +Cc: Stephen Rothwell, linux-next
In-Reply-To: <20101119091629.ddf35bec.randy.dunlap@oracle.com>
On Fri, 19 Nov 2010 09:16:29 -0800 Randy Dunlap wrote:
> On Fri, 19 Nov 2010 14:32:07 +1100 Stephen Rothwell wrote:
>
> > Hi all,
> >
> > Changes since 20101118:
>
>
> when CONFIG_RT_MUTEXES is not enabled:
>
> kernel/rtmutex_common.h:81: error: 'struct task_struct' has no member named 'pi_waiters'
> kernel/rtmutex_common.h:87: error: 'struct task_struct' has no member named 'pi_waiters'
This build error still occurs in linux-next 20101202.
---
~Randy
*** Remember to use Documentation/SubmitChecklist when testing your code ***
^ permalink raw reply
* [PATCH -next] serial: fix pch_uart kconfig & build
From: Randy Dunlap @ 2010-12-02 17:19 UTC (permalink / raw)
To: Zimny Lech, gregkh, akpm
Cc: Stephen Rothwell, linux-next, LKML, Tomoya MORINAGA
In-Reply-To: <AANLkTi=aZ3Gm5rkqAh8j-bOvvKULge6Hm5cN_mEovVdq@mail.gmail.com>
From: Randy Dunlap <randy.dunlap@oracle.com>
The dma_request_channel/dma_release_channel interfaces are not
built when DMADEVICES is not enabled, so make the driver depend on
DMADEVICES. Also, the help text says that the driver enables & uses
PCH_DMA, which is not enabled, so select that.
ERROR: "__dma_request_channel" [drivers/serial/pch_uart.ko] undefined!
ERROR: "dma_release_channel" [drivers/serial/pch_uart.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Reported-by: Zimny Lech <napohybelskurwysynom2010@gmail.com>
---
drivers/serial/Kconfig | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
This driver seems to have some other issues:
drivers/serial/pch_uart.c: In function 'dma_handle_rx':
drivers/serial/pch_uart.c:685: warning: cast from pointer to integer of different size
drivers/serial/pch_uart.c: In function 'dma_handle_tx':
drivers/serial/pch_uart.c:778: warning: cast from pointer to integer of different size
drivers/serial/pch_uart.c: In function 'pch_uart_init_port':
drivers/serial/pch_uart.c:1289: warning: cast to pointer from integer of different size
drivers/serial/pch_uart.c: In function 'pch_uart_exit_port':
drivers/serial/pch_uart.c:1328: warning: cast from pointer to integer of different size
--- linux-next-20101202.orig/drivers/serial/Kconfig
+++ linux-next-20101202/drivers/serial/Kconfig
@@ -1650,8 +1650,9 @@ config SERIAL_IFX6X60
config SERIAL_PCH_UART
tristate "Intel EG20T PCH UART"
+ depends on PCI && DMADEVICES
select SERIAL_CORE
- depends on PCI
+ select PCH_DMA
help
This driver is for PCH(Platform controller Hub) UART of Intel EG20T
which is an IOH(Input/Output Hub) for x86 embedded processor.
^ permalink raw reply
* Re: linux-next: Tree for December 2
From: Zimny Lech @ 2010-12-02 13:52 UTC (permalink / raw)
To: Stephen Rothwell; +Cc: linux-next, LKML, Tomoya MORINAGA
In-Reply-To: <20101202140943.c9742beb.sfr@canb.auug.org.au>
Ave
2010/12/2 Stephen Rothwell <sfr@canb.auug.org.au>:
> Hi all,
>
> Changes since 20101201:
>
WARNING: modpost: Found 4 section mismatch(es).
To see full details build your kernel with:
'make CONFIG_DEBUG_SECTION_MISMATCH=y'
GEN .version
CHK include/generated/compile.h
UPD include/generated/compile.h
CC init/version.o
LD init/built-in.o
LD .tmp_vmlinux1
drivers/built-in.o: In function `pch_request_dma':
/home/test/linux-2.6/drivers/serial/pch_uart.c:565: undefined
reference to `__dma_request_channel'
/home/test/linux-2.6/drivers/serial/pch_uart.c:577: undefined
reference to `__dma_request_channel'
/home/test/linux-2.6/drivers/serial/pch_uart.c:580: undefined
reference to `dma_release_channel'
drivers/built-in.o: In function `pch_free_dma':
/home/test/linux-2.6/drivers/serial/pch_uart.c:519: undefined
reference to `dma_release_channel'
/home/test/linux-2.6/drivers/serial/pch_uart.c:523: undefined
reference to `dma_release_channel'
make[1]: *** [.tmp_vmlinux1] Error 1
make: *** [sub-make] Error 2
--
Slawa!
Zimny "Spie dziadu!" Lech z Wawelu
That is not dead which can eternal lie.
And with strange aeons even death may die.
^ permalink raw reply
* Re: linux-next: manual merge of the staging tree with the staging.current tree
From: Greg KH @ 2010-12-02 4:00 UTC (permalink / raw)
To: Stephen Rothwell; +Cc: linux-next, linux-kernel, Randy Dunlap, Pekka Enberg
In-Reply-To: <20101202132254.93e019c7.sfr@canb.auug.org.au>
On Thu, Dec 02, 2010 at 01:22:54PM +1100, Stephen Rothwell wrote:
> Hi Greg,
>
> Today's linux-next merge of the staging tree got a conflict in
> drivers/staging/winbond/sysdef.h between commit
> 412dc7f368bf10a8049a8a4c41abbfd0108742e7 ("staging: fix winbond build,
> needs delay.h") from the staging.current tree and commit
> ddee7e28e7d5e4ba2b8537c6a59b035745c250bb ("Staging: w35und: Remove empty
> sysdef.h header") from the staging tree.
>
> I removed the file. I wonder if
> drivers/staging/winbond/phy_calibration.c and
> drivers/staging/winbond/reg.c now need their own includes of
> linux/delay.h ...
Heh, probably. I'll handle this merge when thes staging.current code
goes to Linus this week.
thanks,
greg k-h
^ permalink raw reply
* Re: linux-next: manual merge of the staging tree with the staging.current tree
From: Randy Dunlap @ 2010-12-02 3:20 UTC (permalink / raw)
To: Stephen Rothwell; +Cc: Greg KH, linux-next, linux-kernel, Pekka Enberg
In-Reply-To: <20101202132254.93e019c7.sfr@canb.auug.org.au>
On 12/01/10 18:22, Stephen Rothwell wrote:
> Hi Greg,
>
> Today's linux-next merge of the staging tree got a conflict in
> drivers/staging/winbond/sysdef.h between commit
> 412dc7f368bf10a8049a8a4c41abbfd0108742e7 ("staging: fix winbond build,
> needs delay.h") from the staging.current tree and commit
> ddee7e28e7d5e4ba2b8537c6a59b035745c250bb ("Staging: w35und: Remove empty
> sysdef.h header") from the staging tree.
>
> I removed the file. I wonder if
> drivers/staging/winbond/phy_calibration.c and
> drivers/staging/winbond/reg.c now need their own includes of
> linux/delay.h ...
Probably, since sysdef.h was no longer an empty file.
--
~Randy
*** Remember to use Documentation/SubmitChecklist when testing your code ***
^ permalink raw reply
* linux-next: Tree for December 2
From: Stephen Rothwell @ 2010-12-02 3:09 UTC (permalink / raw)
To: linux-next; +Cc: LKML
[-- Attachment #1: Type: text/plain, Size: 8863 bytes --]
Hi all,
Changes since 20101201:
The v4l-dvb tree still has its build failure for which I applied a patch.
The acpi tree gained a build failure so I used the version from
next-20101201.
The sound-asoc tree lost its build failure.
The tip tree still has its build failures so I have reverted 3 commits.
The staging tree gained a conflict against the staging.current tree.
----------------------------------------------------------------------------
I have created today's linux-next tree at
git://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
(patches at http://www.kernel.org/pub/linux/kernel/v2.6/next/ ). If you
are tracking the linux-next tree using git, you should not use "git pull"
to do so as that will try to merge the new linux-next release with the
old one. You should use "git fetch" as mentioned in the FAQ on the wiki
(see below).
You can see which trees have been included by looking in the Next/Trees
file in the source. There are also quilt-import.log and merge.log files
in the Next directory. Between each merge, the tree was built with
a ppc64_defconfig for powerpc and an allmodconfig for x86_64. After the
final fixups (if any), it is also built with powerpc allnoconfig (32 and
64 bit), ppc44x_defconfig and allyesconfig (minus
CONFIG_PROFILE_ALL_BRANCHES - this fails its final link) and i386, sparc
and sparc64 defconfig. These builds also have
CONFIG_ENABLE_WARN_DEPRECATED, CONFIG_ENABLE_MUST_CHECK and
CONFIG_DEBUG_INFO disabled when necessary.
Below is a summary of the state of the merge.
We are up to 181 trees (counting Linus' and 26 trees of patches pending
for Linus' tree), more are welcome (even if they are currently empty).
Thanks to those who have contributed, and to those who haven't, please do.
Status of my local build tests will be at
http://kisskb.ellerman.id.au/linux-next . If maintainers want to give
advice about cross compilers/configs that work, we are always open to add
more builds.
Thanks to Randy Dunlap for doing many randconfig builds.
There is a wiki covering stuff to do with linux-next at
http://linux.f-seidel.de/linux-next/pmwiki/ . Thanks to Frank Seidel.
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
$ git checkout master
$ git reset --hard stable
Merging origin/master
Merging fixes/fixes
Merging arm-current/master
Merging m68k-current/for-linus
Merging powerpc-merge/merge
Merging sparc-current/master
Merging scsi-rc-fixes/master
Merging net-current/master
Merging sound-current/for-linus
Merging pci-current/for-linus
Merging wireless-current/master
Merging kbuild-current/rc-fixes
Merging driver-core.current/driver-core-linus
Merging tty.current/tty-linus
Merging usb.current/usb-linus
Merging staging.current/staging-linus
Merging cpufreq-current/fixes
Merging input-current/for-linus
Merging md-current/for-linus
Merging audit-current/for-linus
Merging crypto-current/master
Merging ide-curent/master
Merging dwmw2/master
Merging sh-current/sh-fixes-for-linus
Merging rmobile-current/rmobile-fixes-for-linus
Merging fbdev-current/fbdev-fixes-for-linus
Merging gcl-current/merge
Merging arm/devel
Merging davinci/davinci-next
Merging i.MX/for-next
Merging msm/for-next
Merging omap/for-next
Merging pxa/for-next
Merging samsung/next-samsung
Merging s5p/for-next
Merging tegra/for-next
Merging ux500-core/ux500-core
Merging avr32/avr32-arch
Merging blackfin/for-linus
Merging cris/for-next
Merging ia64/test
Merging m68k/for-next
Merging m68knommu/for-next
Merging microblaze/next
Merging mips/mips-for-linux-next
Merging parisc/next
Merging powerpc/next
Merging 4xx/next
Merging 52xx-and-virtex/next
Merging galak/next
Merging s390/features
Merging sh/sh-latest
Merging rmobile/rmobile-latest
CONFLICT (content): Merge conflict in arch/arm/mach-shmobile/Kconfig
Applying: rmobile: merge fixup for clkdev changes
Merging sparc/master
Merging tile/master
Merging xtensa/master
CONFLICT (content): Merge conflict in arch/xtensa/configs/iss_defconfig
Merging ceph/for-next
Merging cifs/master
Merging configfs/linux-next
Merging ecryptfs/next
Merging ext3/for_next
Merging ext4/next
Merging fatfs/master
Merging fuse/for-next
Merging gfs2/master
Merging hfsplus/for-next
Merging jfs/next
Merging logfs/master
CONFLICT (content): Merge conflict in fs/logfs/logfs.h
Merging nfs/linux-next
Merging nfsd/nfsd-next
Merging nilfs2/for-next
Merging ocfs2/linux-next
Merging omfs/for-next
Merging squashfs/master
Merging udf/for_next
Merging v9fs/for-next
Merging ubifs/linux-next
Merging xfs/master
Merging vfs/for-next
Merging pci/linux-next
CONFLICT (content): Merge conflict in drivers/pci/pci-sysfs.c
Merging hid/for-next
CONFLICT (content): Merge conflict in drivers/hid/hid-input.c
Merging quilt/i2c
Merging bjdooks-i2c/next-i2c
Merging quilt/jdelvare-hwmon
Merging hwmon-staging/hwmon-next
Merging quilt/kernel-doc
Merging v4l-dvb/master
Applying: media: const and __devinitdata do not mix
Merging kbuild/for-next
Merging kconfig/for-next
Merging ide/master
Merging libata/NEXT
Merging infiniband/for-next
Merging acpi/test
$ git reset --hard HEAD^
Merging refs/next/20101201/acpi
Merging idle-test/idle-test
Merging ieee1394/for-next
Merging ubi/linux-next
Merging kvm/linux-next
Merging dlm/next
Merging swiotlb/master
Merging ibft/master
Merging scsi/master
Merging async_tx/next
Merging net/master
Merging wireless/master
Merging bluetooth/master
Merging mtd/master
Merging crypto/master
Merging sound/for-next
Merging sound-asoc/for-next
Merging cpufreq/next
Merging quilt/rr
Merging input/next
Merging lsm/for-next
Merging block/for-next
Merging quilt/device-mapper
Merging embedded/master
Merging firmware/master
Merging pcmcia/master
Merging battery/master
Merging leds/for-mm
Merging backlight/for-mm
Merging mmc/mmc-next
Merging kgdb/kgdb-next
Merging slab/for-next
Merging uclinux/for-next
Merging md/for-next
Merging mfd/for-next
CONFLICT (content): Merge conflict in drivers/mfd/wm8994-core.c
Merging hdlc/hdlc-next
Merging drm/drm-next
Merging fbdev/master
Merging viafb/viafb-next
Merging omap_dss2/for-next
Merging voltage/for-next
Merging security-testing/next
Merging selinux/master
Merging lblnet/master
Merging agp/agp-next
Merging watchdog/master
Merging bdev/master
Merging dwmw2-iommu/master
Merging cputime/cputime
Merging osd/linux-next
Merging jc_docs/docs-next
Merging nommu/master
Merging trivial/for-next
CONFLICT (content): Merge conflict in MAINTAINERS
CONFLICT (content): Merge conflict in drivers/scsi/bfa/bfa_fcpim.c
Merging audit/for-next
Merging suspend/linux-next
Merging fsnotify/for-next
Merging irda/for-next
Merging catalin/for-next
Merging alacrity/linux-next
CONFLICT (content): Merge conflict in drivers/Makefile
CONFLICT (content): Merge conflict in include/linux/Kbuild
CONFLICT (content): Merge conflict in lib/Kconfig
Merging i7core_edac/linux_next
Merging i7300_edac/linux_next
Merging devicetree/next-devicetree
Merging spi/next-spi
Merging tip/auto-latest
[master 3cdecc6] Revert "x86, nmi_watchdog: Remove all stub function calls from old nmi_watchdog"
$ git commit -v -a[master 8c7c55b] Revert "x86, nmi_watchdog: Remove the old nmi_watchdog"
[master 704db18] Revert "perf, arch: Cleanup perf-pmu init vs lockup-detector"
Merging rcu/rcu/next
Merging oprofile/for-next
Merging xen/upstream/xen
Merging swiotlb-xen/master
Merging xen-pvhvm/linux-next
Merging edac-amd/for-next
Merging percpu/for-next
Merging workqueues/for-next
Merging sfi/sfi-test
Merging asm-generic/next
Merging drivers-x86/linux-next
Merging hwpoison/hwpoison
Merging sysctl/master
Merging driver-core/driver-core-next
Merging tty/tty-next
Merging usb/usb-next
Merging staging/staging-next
CONFLICT (content): Merge conflict in drivers/staging/batman-adv/hard-interface.c
CONFLICT (content): Merge conflict in drivers/staging/batman-adv/soft-interface.c
CONFLICT (delete/modify): drivers/staging/winbond/sysdef.h deleted in staging/staging-next and modified in HEAD. Version HEAD of drivers/staging/winbond/sysdef.h left in tree.
$ git rm -f drivers/staging/winbond/sysdef.h
Merging slabh/slabh
Merging bkl-trivial/trivial
Merging bkl-llseek/llseek
Merging bkl-vfs/vfs
Merging bkl-config/config
CONFLICT (content): Merge conflict in arch/powerpc/kernel/setup_64.c
CONFLICT (content): Merge conflict in include/linux/hardirq.h
CONFLICT (content): Merge conflict in include/linux/smp_lock.h
Merging irqflags/master
Merging cleancache/linux-next
CONFLICT (content): Merge conflict in fs/ocfs2/super.c
CONFLICT (content): Merge conflict in include/linux/fs.h
CONFLICT (content): Merge conflict in mm/Kconfig
Merging scsi-post-merge/merge-base:master
[-- Attachment #2: Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply
* linux-next: manual merge of the staging tree with the staging.current tree
From: Stephen Rothwell @ 2010-12-02 2:22 UTC (permalink / raw)
To: Greg KH; +Cc: linux-next, linux-kernel, Randy Dunlap, Pekka Enberg
[-- Attachment #1: Type: text/plain, Size: 642 bytes --]
Hi Greg,
Today's linux-next merge of the staging tree got a conflict in
drivers/staging/winbond/sysdef.h between commit
412dc7f368bf10a8049a8a4c41abbfd0108742e7 ("staging: fix winbond build,
needs delay.h") from the staging.current tree and commit
ddee7e28e7d5e4ba2b8537c6a59b035745c250bb ("Staging: w35und: Remove empty
sysdef.h header") from the staging tree.
I removed the file. I wonder if
drivers/staging/winbond/phy_calibration.c and
drivers/staging/winbond/reg.c now need their own includes of
linux/delay.h ...
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply
* linux-next: build failure after merge of the acpi tree
From: Stephen Rothwell @ 2010-12-02 0:22 UTC (permalink / raw)
To: Len Brown; +Cc: linux-next, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 1341 bytes --]
Hi Len,
After merging the acpi tree, today's linux-next build (powerpc
ppc64_defconfig) failed like this:
In file included from drivers/video/output.c:25:
include/linux/video_output.h: In function 'video_output_register':
include/linux/video_output.h:49: error: implicit declaration of function 'ERR_PTR'
include/linux/video_output.h:49: warning: return makes pointer from integer without a cast
In file included from drivers/video/output.c:27:
include/linux/err.h: At top level:
include/linux/err.h:22: error: conflicting types for 'ERR_PTR'
include/linux/video_output.h:49: note: previous implicit declaration of 'ERR_PTR' was here
drivers/video/output.c:84: error: redefinition of 'video_output_register'
include/linux/video_output.h:44: note: previous definition of 'video_output_register' was here
drivers/video/output.c:114: error: redefinition of 'video_output_unregister'
include/linux/video_output.h:51: note: previous definition of 'video_output_unregister' was here
Caused by commit 16d21716c8849c3283d1b9e590e6fe8d1966f4b7 ("ACPI: video:
fix build for VIDEO_OUTPUT_CONTROL=n"). See Rule 1 in
Documentation/SubmitChecklist.
I have used the version of the acpi tree from next-20101201 for today.
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
[-- Attachment #2: Type: application/pgp-signature, Size: 490 bytes --]
^ permalink raw reply
* Re: linux-next: Tree for December 1 (kconfig question)
From: Randy Dunlap @ 2010-12-01 22:58 UTC (permalink / raw)
To: Zimny Lech; +Cc: Stephen Rothwell, linux-next, LKML, linux kbuild list
In-Reply-To: <AANLkTikB5aHZRL9hJT-ODqUEbiCtQN3W-vk8OUOCkzNb@mail.gmail.com>
On 12/01/10 14:18, Zimny Lech wrote:
> 2010/12/1 Randy Dunlap <randy.dunlap@oracle.com>:
>> On Wed, 1 Dec 2010 17:04:38 +0100 Zimny Lech wrote:
>>
>>> Ave
>>>
>>> 2010/12/1 Stephen Rothwell <sfr@canb.auug.org.au>:
>>>> Hi all,
>>>>
>>>> Changes since 20101130:
>>>>
>>>
>>> I remember, I reported something similar a week or two ago
>>>
>>> GEN /home/test/linux-2.6-obj/Makefile
>>> scripts/kconfig/conf --silentoldconfig Kconfig
>>> .config:167:warning: override: SLOB changes choice state
>>> warning: (IA32_EMULATION && X86_64) selects COMPAT_BINFMT_ELF which
>>> has unmet direct dependencies (COMPAT && BINFMT_ELF)
>>> warning: (MTD_NAND && MTD || MTD_DOC2000 && MTD || MTD_DOC2001 && MTD
>>> || MTD_DOC2001PLUS && MTD) selects MTD_NAND_IDS which has unmet direct
>>> dependencies (MTD
>>> warning: (CRYPTO_LRW && CRYPTO && EXPERIMENTAL || CRYPTO_XTS && CRYPTO
>>> && EXPERIMENTAL || CRYPTO_GHASH && CRYPTO) selects CRYPTO_GF128MUL
>>> which has unmet dire
>>> *
>>> * Restart config...
>>> *
>>> *
>>> * Kernel hacking
>>> *
>>> Enable __deprecated logic (ENABLE_WARN_DEPRECATED) [Y/n/?] y
>>> Enable __must_check logic (ENABLE_MUST_CHECK) [N/y/?] n
>>> Warn for stack frames larger than (needs gcc 4.4) (FRAME_WARN) [2048] 2048
>>> Magic SysRq key (MAGIC_SYSRQ) [N/y/?] n
>>> Strip assembler-generated symbols during link (STRIP_ASM_SYMS) [N/y/?] n
>>> Enable unused/obsolete exported symbols (UNUSED_SYMBOLS) [Y/n/?] y
>>> Debug Filesystem (DEBUG_FS) [Y/?] y
>>> Run 'make headers_check' when building vmlinux (HEADERS_CHECK) [N/y/?] n
>>> Kernel debugging (DEBUG_KERNEL) [Y/n/?] y
>>> Debug shared IRQ handlers (DEBUG_SHIRQ) [N/y/?] n
>>> Detect Hard and Soft Lockups (LOCKUP_DETECTOR) [Y/n/?] y
>>> Panic (Reboot) On Soft Lockups (BOOTPARAM_SOFTLOCKUP_PANIC) [Y/n/?] y
>>> Detect Hung Tasks (DETECT_HUNG_TASK) [N/y/?] n
>>> Debug object operations (DEBUG_OBJECTS) [N/y/?] n
>>> RT Mutex debugging, deadlock detection (DEBUG_RT_MUTEXES) [Y/n/?] y
>>> Built-in scriptable tester for rt-mutexes (RT_MUTEX_TESTER) [Y/n/?] y
>>> Spinlock and rw-lock debugging: basic checks (DEBUG_SPINLOCK) [Y/?] y
>>> Mutex debugging: basic checks (DEBUG_MUTEXES) [Y/?] y
>>> Lock debugging: detect incorrect freeing of live locks
>>> (DEBUG_LOCK_ALLOC) [Y/?] y
>>> Lock debugging: prove locking correctness (PROVE_LOCKING) [Y/n/?] y
>>> RCU debugging: prove RCU correctness (PROVE_RCU) [Y/n/?] y
>>> RCU debugging: don't disable PROVE_RCU on first splat
>>> (PROVE_RCU_REPEATEDLY) [N/y/?] n
>>> RCU debugging: sparse-based checks for pointer usage
>>> (SPARSE_RCU_POINTER) [Y/n/?] y
>>> Lock usage statistics (LOCK_STAT) [N/y/?] n
>>> Lock dependency engine debugging (DEBUG_LOCKDEP) [Y/n/?] y
>>> Spinlock debugging: sleep-inside-spinlock checking
>>> (DEBUG_SPINLOCK_SLEEP) [Y/n/?] y
>>> Locking API boot-time self-tests (DEBUG_LOCKING_API_SELFTESTS) [N/y/?] n
>>> kobject debugging (DEBUG_KOBJECT) [N/y/?] n
>>> Compile the kernel with debug info (DEBUG_INFO) [N/y/?] n
>>> Debug VM (DEBUG_VM) [Y/n/?] y
>>> Debug VM translations (DEBUG_VIRTUAL) [Y/n/?] y
>>> Debug filesystem writers count (DEBUG_WRITECOUNT) [N/y/?] n
>>> Debug memory initialisation (DEBUG_MEMORY_INIT) [Y/n/?] y
>>> Debug linked list manipulation (DEBUG_LIST) [Y/n/?] y
>>> Linked list sorting test (TEST_LIST_SORT) [N/y/?] n
>>> Debug SG table operations (DEBUG_SG) [N/y/?] n
>>> Debug notifier call chains (DEBUG_NOTIFIERS) [N/y/?] n
>>> Debug credential management (DEBUG_CREDENTIALS) [Y/n/?] y
>>> Compile the kernel with frame pointers (FRAME_POINTER) [Y/?] y
>>> torture tests for RCU (RCU_TORTURE_TEST) [N/y/?] n
>>> Check for stalled CPUs delaying RCU grace periods
>>> (RCU_CPU_STALL_DETECTOR) [Y/n/?] y
>>> RCU CPU stall timeout in seconds (RCU_CPU_STALL_TIMEOUT) [60] 60
>>> RCU CPU stall checking starts automatically at boot
>>> (RCU_CPU_STALL_DETECTOR_RUNNABLE) [Y/n/?] y
>>> Self test for the backtrace code (BACKTRACE_SELF_TEST) [Y/n/?] y
>>> Force extended block device numbers and spread them
>>> (DEBUG_BLOCK_EXT_DEVT) [N/y/?] n
>>> Force weak per-cpu definitions (DEBUG_FORCE_WEAK_PER_CPU) [N/y/?] n
>>> Linux Kernel Dump Test Tool Module (LKDTM) [N/y/?] n
>>> CPU notifier error injection module (CPU_NOTIFIER_ERROR_INJECT) [Y/n/?] y
>>> Fault-injection framework (FAULT_INJECTION) [Y/n/?] y
>>> Fault-injection capabilitiy for alloc_pages() (FAIL_PAGE_ALLOC) [N/y/?] n
>>> Fault-injection capability for disk IO (FAIL_MAKE_REQUEST) [Y/n/?] y
>>> Fault-injection capability for faking disk interrupts
>>> (FAIL_IO_TIMEOUT) [Y/n/?] y
>>> Debugfs entries for fault-injection capabilities
>>> (FAULT_INJECTION_DEBUG_FS) [N/y/?] n
>>> Debug page memory allocations (DEBUG_PAGEALLOC) [N/y/?] (NEW) aborted!
>>>
>>> Console input/output is redirected. Run 'make oldconfig' to update
>>> configuration.
>>>
>>> make[3]: *** [silentoldconfig] Error 1
>>> make[2]: *** [silentoldconfig] Error 2
>>> make[1]: *** No rule to make target `include/config/auto.conf', needed
>>> by `include/config/kernel.release'. Stop.
>>> make: *** [sub-make] Error 2
>>
>>
>> This is a problem. Any idea how you achieved this?
>
> Believe if I say that it was generated by make randconfig? Or this is
> so amazing that you would not believe? :)
Yeah, that's what I expected.
kconfig people: Is there some way that 'make randconfig' could generate
this?
# CONFIG_SLAB is not set
CONFIG_SLUB=y
CONFIG_SLOB=y
> This build was done (as always) by my build script - the same that I
> send you once.
>
> It's simple:
> make mrproper
> make O=../dir mrproper
> and in loop:
> make randconfig
> make
>
> This bug appeared on third run through the loop.
>
>>
>> # CONFIG_SLAB is not set
>> CONFIG_SLUB=y
>> CONFIG_SLOB=y
>>
>> These are part of a choice and should be mutually exclusive.
--
~Randy
*** Remember to use Documentation/SubmitChecklist when testing your code ***
^ permalink raw reply
* Re: linux-next: Tree for December 1
From: Zimny Lech @ 2010-12-01 22:18 UTC (permalink / raw)
To: Randy Dunlap; +Cc: Stephen Rothwell, linux-next, LKML
In-Reply-To: <20101201122318.5af8ef6f.randy.dunlap@oracle.com>
2010/12/1 Randy Dunlap <randy.dunlap@oracle.com>:
> On Wed, 1 Dec 2010 17:04:38 +0100 Zimny Lech wrote:
>
>> Ave
>>
>> 2010/12/1 Stephen Rothwell <sfr@canb.auug.org.au>:
>> > Hi all,
>> >
>> > Changes since 20101130:
>> >
>>
>> I remember, I reported something similar a week or two ago
>>
>> GEN /home/test/linux-2.6-obj/Makefile
>> scripts/kconfig/conf --silentoldconfig Kconfig
>> .config:167:warning: override: SLOB changes choice state
>> warning: (IA32_EMULATION && X86_64) selects COMPAT_BINFMT_ELF which
>> has unmet direct dependencies (COMPAT && BINFMT_ELF)
>> warning: (MTD_NAND && MTD || MTD_DOC2000 && MTD || MTD_DOC2001 && MTD
>> || MTD_DOC2001PLUS && MTD) selects MTD_NAND_IDS which has unmet direct
>> dependencies (MTD
>> warning: (CRYPTO_LRW && CRYPTO && EXPERIMENTAL || CRYPTO_XTS && CRYPTO
>> && EXPERIMENTAL || CRYPTO_GHASH && CRYPTO) selects CRYPTO_GF128MUL
>> which has unmet dire
>> *
>> * Restart config...
>> *
>> *
>> * Kernel hacking
>> *
>> Enable __deprecated logic (ENABLE_WARN_DEPRECATED) [Y/n/?] y
>> Enable __must_check logic (ENABLE_MUST_CHECK) [N/y/?] n
>> Warn for stack frames larger than (needs gcc 4.4) (FRAME_WARN) [2048] 2048
>> Magic SysRq key (MAGIC_SYSRQ) [N/y/?] n
>> Strip assembler-generated symbols during link (STRIP_ASM_SYMS) [N/y/?] n
>> Enable unused/obsolete exported symbols (UNUSED_SYMBOLS) [Y/n/?] y
>> Debug Filesystem (DEBUG_FS) [Y/?] y
>> Run 'make headers_check' when building vmlinux (HEADERS_CHECK) [N/y/?] n
>> Kernel debugging (DEBUG_KERNEL) [Y/n/?] y
>> Debug shared IRQ handlers (DEBUG_SHIRQ) [N/y/?] n
>> Detect Hard and Soft Lockups (LOCKUP_DETECTOR) [Y/n/?] y
>> Panic (Reboot) On Soft Lockups (BOOTPARAM_SOFTLOCKUP_PANIC) [Y/n/?] y
>> Detect Hung Tasks (DETECT_HUNG_TASK) [N/y/?] n
>> Debug object operations (DEBUG_OBJECTS) [N/y/?] n
>> RT Mutex debugging, deadlock detection (DEBUG_RT_MUTEXES) [Y/n/?] y
>> Built-in scriptable tester for rt-mutexes (RT_MUTEX_TESTER) [Y/n/?] y
>> Spinlock and rw-lock debugging: basic checks (DEBUG_SPINLOCK) [Y/?] y
>> Mutex debugging: basic checks (DEBUG_MUTEXES) [Y/?] y
>> Lock debugging: detect incorrect freeing of live locks
>> (DEBUG_LOCK_ALLOC) [Y/?] y
>> Lock debugging: prove locking correctness (PROVE_LOCKING) [Y/n/?] y
>> RCU debugging: prove RCU correctness (PROVE_RCU) [Y/n/?] y
>> RCU debugging: don't disable PROVE_RCU on first splat
>> (PROVE_RCU_REPEATEDLY) [N/y/?] n
>> RCU debugging: sparse-based checks for pointer usage
>> (SPARSE_RCU_POINTER) [Y/n/?] y
>> Lock usage statistics (LOCK_STAT) [N/y/?] n
>> Lock dependency engine debugging (DEBUG_LOCKDEP) [Y/n/?] y
>> Spinlock debugging: sleep-inside-spinlock checking
>> (DEBUG_SPINLOCK_SLEEP) [Y/n/?] y
>> Locking API boot-time self-tests (DEBUG_LOCKING_API_SELFTESTS) [N/y/?] n
>> kobject debugging (DEBUG_KOBJECT) [N/y/?] n
>> Compile the kernel with debug info (DEBUG_INFO) [N/y/?] n
>> Debug VM (DEBUG_VM) [Y/n/?] y
>> Debug VM translations (DEBUG_VIRTUAL) [Y/n/?] y
>> Debug filesystem writers count (DEBUG_WRITECOUNT) [N/y/?] n
>> Debug memory initialisation (DEBUG_MEMORY_INIT) [Y/n/?] y
>> Debug linked list manipulation (DEBUG_LIST) [Y/n/?] y
>> Linked list sorting test (TEST_LIST_SORT) [N/y/?] n
>> Debug SG table operations (DEBUG_SG) [N/y/?] n
>> Debug notifier call chains (DEBUG_NOTIFIERS) [N/y/?] n
>> Debug credential management (DEBUG_CREDENTIALS) [Y/n/?] y
>> Compile the kernel with frame pointers (FRAME_POINTER) [Y/?] y
>> torture tests for RCU (RCU_TORTURE_TEST) [N/y/?] n
>> Check for stalled CPUs delaying RCU grace periods
>> (RCU_CPU_STALL_DETECTOR) [Y/n/?] y
>> RCU CPU stall timeout in seconds (RCU_CPU_STALL_TIMEOUT) [60] 60
>> RCU CPU stall checking starts automatically at boot
>> (RCU_CPU_STALL_DETECTOR_RUNNABLE) [Y/n/?] y
>> Self test for the backtrace code (BACKTRACE_SELF_TEST) [Y/n/?] y
>> Force extended block device numbers and spread them
>> (DEBUG_BLOCK_EXT_DEVT) [N/y/?] n
>> Force weak per-cpu definitions (DEBUG_FORCE_WEAK_PER_CPU) [N/y/?] n
>> Linux Kernel Dump Test Tool Module (LKDTM) [N/y/?] n
>> CPU notifier error injection module (CPU_NOTIFIER_ERROR_INJECT) [Y/n/?] y
>> Fault-injection framework (FAULT_INJECTION) [Y/n/?] y
>> Fault-injection capabilitiy for alloc_pages() (FAIL_PAGE_ALLOC) [N/y/?] n
>> Fault-injection capability for disk IO (FAIL_MAKE_REQUEST) [Y/n/?] y
>> Fault-injection capability for faking disk interrupts
>> (FAIL_IO_TIMEOUT) [Y/n/?] y
>> Debugfs entries for fault-injection capabilities
>> (FAULT_INJECTION_DEBUG_FS) [N/y/?] n
>> Debug page memory allocations (DEBUG_PAGEALLOC) [N/y/?] (NEW) aborted!
>>
>> Console input/output is redirected. Run 'make oldconfig' to update
>> configuration.
>>
>> make[3]: *** [silentoldconfig] Error 1
>> make[2]: *** [silentoldconfig] Error 2
>> make[1]: *** No rule to make target `include/config/auto.conf', needed
>> by `include/config/kernel.release'. Stop.
>> make: *** [sub-make] Error 2
>
>
> This is a problem. Any idea how you achieved this?
Believe if I say that it was generated by make randconfig? Or this is
so amazing that you would not believe? :)
This build was done (as always) by my build script - the same that I
send you once.
It's simple:
make mrproper
make O=../dir mrproper
and in loop:
make randconfig
make
This bug appeared on third run through the loop.
>
> # CONFIG_SLAB is not set
> CONFIG_SLUB=y
> CONFIG_SLOB=y
>
> These are part of a choice and should be mutually exclusive.
>
> ---
> ~Randy
> *** Remember to use Documentation/SubmitChecklist when testing your code ***
>
--
Slawa!
Zimny "Spie dziadu!" Lech z Wawelu
That is not dead which can eternal lie.
And with strange aeons even death may die.
^ permalink raw reply
* Re: linux-next: Tree for December 1
From: Randy Dunlap @ 2010-12-01 20:23 UTC (permalink / raw)
To: Zimny Lech; +Cc: Stephen Rothwell, linux-next, LKML
In-Reply-To: <AANLkTimt-Td_Fv3xb8xF8NVg5NtZ2zkuUfNZrd9+BDrh@mail.gmail.com>
On Wed, 1 Dec 2010 17:04:38 +0100 Zimny Lech wrote:
> Ave
>
> 2010/12/1 Stephen Rothwell <sfr@canb.auug.org.au>:
> > Hi all,
> >
> > Changes since 20101130:
> >
>
> I remember, I reported something similar a week or two ago
>
> GEN /home/test/linux-2.6-obj/Makefile
> scripts/kconfig/conf --silentoldconfig Kconfig
> .config:167:warning: override: SLOB changes choice state
> warning: (IA32_EMULATION && X86_64) selects COMPAT_BINFMT_ELF which
> has unmet direct dependencies (COMPAT && BINFMT_ELF)
> warning: (MTD_NAND && MTD || MTD_DOC2000 && MTD || MTD_DOC2001 && MTD
> || MTD_DOC2001PLUS && MTD) selects MTD_NAND_IDS which has unmet direct
> dependencies (MTD
> warning: (CRYPTO_LRW && CRYPTO && EXPERIMENTAL || CRYPTO_XTS && CRYPTO
> && EXPERIMENTAL || CRYPTO_GHASH && CRYPTO) selects CRYPTO_GF128MUL
> which has unmet dire
> *
> * Restart config...
> *
> *
> * Kernel hacking
> *
> Enable __deprecated logic (ENABLE_WARN_DEPRECATED) [Y/n/?] y
> Enable __must_check logic (ENABLE_MUST_CHECK) [N/y/?] n
> Warn for stack frames larger than (needs gcc 4.4) (FRAME_WARN) [2048] 2048
> Magic SysRq key (MAGIC_SYSRQ) [N/y/?] n
> Strip assembler-generated symbols during link (STRIP_ASM_SYMS) [N/y/?] n
> Enable unused/obsolete exported symbols (UNUSED_SYMBOLS) [Y/n/?] y
> Debug Filesystem (DEBUG_FS) [Y/?] y
> Run 'make headers_check' when building vmlinux (HEADERS_CHECK) [N/y/?] n
> Kernel debugging (DEBUG_KERNEL) [Y/n/?] y
> Debug shared IRQ handlers (DEBUG_SHIRQ) [N/y/?] n
> Detect Hard and Soft Lockups (LOCKUP_DETECTOR) [Y/n/?] y
> Panic (Reboot) On Soft Lockups (BOOTPARAM_SOFTLOCKUP_PANIC) [Y/n/?] y
> Detect Hung Tasks (DETECT_HUNG_TASK) [N/y/?] n
> Debug object operations (DEBUG_OBJECTS) [N/y/?] n
> RT Mutex debugging, deadlock detection (DEBUG_RT_MUTEXES) [Y/n/?] y
> Built-in scriptable tester for rt-mutexes (RT_MUTEX_TESTER) [Y/n/?] y
> Spinlock and rw-lock debugging: basic checks (DEBUG_SPINLOCK) [Y/?] y
> Mutex debugging: basic checks (DEBUG_MUTEXES) [Y/?] y
> Lock debugging: detect incorrect freeing of live locks
> (DEBUG_LOCK_ALLOC) [Y/?] y
> Lock debugging: prove locking correctness (PROVE_LOCKING) [Y/n/?] y
> RCU debugging: prove RCU correctness (PROVE_RCU) [Y/n/?] y
> RCU debugging: don't disable PROVE_RCU on first splat
> (PROVE_RCU_REPEATEDLY) [N/y/?] n
> RCU debugging: sparse-based checks for pointer usage
> (SPARSE_RCU_POINTER) [Y/n/?] y
> Lock usage statistics (LOCK_STAT) [N/y/?] n
> Lock dependency engine debugging (DEBUG_LOCKDEP) [Y/n/?] y
> Spinlock debugging: sleep-inside-spinlock checking
> (DEBUG_SPINLOCK_SLEEP) [Y/n/?] y
> Locking API boot-time self-tests (DEBUG_LOCKING_API_SELFTESTS) [N/y/?] n
> kobject debugging (DEBUG_KOBJECT) [N/y/?] n
> Compile the kernel with debug info (DEBUG_INFO) [N/y/?] n
> Debug VM (DEBUG_VM) [Y/n/?] y
> Debug VM translations (DEBUG_VIRTUAL) [Y/n/?] y
> Debug filesystem writers count (DEBUG_WRITECOUNT) [N/y/?] n
> Debug memory initialisation (DEBUG_MEMORY_INIT) [Y/n/?] y
> Debug linked list manipulation (DEBUG_LIST) [Y/n/?] y
> Linked list sorting test (TEST_LIST_SORT) [N/y/?] n
> Debug SG table operations (DEBUG_SG) [N/y/?] n
> Debug notifier call chains (DEBUG_NOTIFIERS) [N/y/?] n
> Debug credential management (DEBUG_CREDENTIALS) [Y/n/?] y
> Compile the kernel with frame pointers (FRAME_POINTER) [Y/?] y
> torture tests for RCU (RCU_TORTURE_TEST) [N/y/?] n
> Check for stalled CPUs delaying RCU grace periods
> (RCU_CPU_STALL_DETECTOR) [Y/n/?] y
> RCU CPU stall timeout in seconds (RCU_CPU_STALL_TIMEOUT) [60] 60
> RCU CPU stall checking starts automatically at boot
> (RCU_CPU_STALL_DETECTOR_RUNNABLE) [Y/n/?] y
> Self test for the backtrace code (BACKTRACE_SELF_TEST) [Y/n/?] y
> Force extended block device numbers and spread them
> (DEBUG_BLOCK_EXT_DEVT) [N/y/?] n
> Force weak per-cpu definitions (DEBUG_FORCE_WEAK_PER_CPU) [N/y/?] n
> Linux Kernel Dump Test Tool Module (LKDTM) [N/y/?] n
> CPU notifier error injection module (CPU_NOTIFIER_ERROR_INJECT) [Y/n/?] y
> Fault-injection framework (FAULT_INJECTION) [Y/n/?] y
> Fault-injection capabilitiy for alloc_pages() (FAIL_PAGE_ALLOC) [N/y/?] n
> Fault-injection capability for disk IO (FAIL_MAKE_REQUEST) [Y/n/?] y
> Fault-injection capability for faking disk interrupts
> (FAIL_IO_TIMEOUT) [Y/n/?] y
> Debugfs entries for fault-injection capabilities
> (FAULT_INJECTION_DEBUG_FS) [N/y/?] n
> Debug page memory allocations (DEBUG_PAGEALLOC) [N/y/?] (NEW) aborted!
>
> Console input/output is redirected. Run 'make oldconfig' to update
> configuration.
>
> make[3]: *** [silentoldconfig] Error 1
> make[2]: *** [silentoldconfig] Error 2
> make[1]: *** No rule to make target `include/config/auto.conf', needed
> by `include/config/kernel.release'. Stop.
> make: *** [sub-make] Error 2
This is a problem. Any idea how you achieved this?
# CONFIG_SLAB is not set
CONFIG_SLUB=y
CONFIG_SLOB=y
These are part of a choice and should be mutually exclusive.
---
~Randy
*** Remember to use Documentation/SubmitChecklist when testing your code ***
^ permalink raw reply
* Re: The longest build error ever, ever, ever seen :) (Re:linux-next: Tree for November 26)
From: Greg KH @ 2010-12-01 19:29 UTC (permalink / raw)
To: Randy Dunlap
Cc: Milton Miller, linux-next, Zimny Lech, Valdis Kletnieks,
linux-kernel
In-Reply-To: <20101201103035.0e0b22cf.randy.dunlap@oracle.com>
On Wed, Dec 01, 2010 at 10:30:35AM -0800, Randy Dunlap wrote:
> On Sun, 28 Nov 2010 00:55:14 -0600 Milton Miller wrote:
>
> [also adding linux-next back to cc: list]
>
>
> > On Sat Nov 27 2010 around 13:13:03 EST, Valdis Kletnieks wrote:
> > > On Sat, 27 Nov 2010 08:45:55 PST, Greg KH said:
> > > > On Sat, Nov 27, 2010 at 09:56:45AM +0100, Zimny Lech wrote:
> > > > > Ave!
> > > > >
> > > > > 2010/11/26 Stephen Rothwell <sfr@xxxxxxxxxxxxxxxx>:
> > > > > > Hi all,
> > > > > >
> > > > >
> > > > > OMG, LOL, this one is awesome :) The longest build error ever, ever,
> > > > > ever seen! Fscking awesome, someone gets Guiness World Record :)
> > > > >
> > > > > LD drivers/staging/built-in.o
> > > > > drivers/staging/rtl8192e/built-in.o: In function `rtl8192_setBBreg':
> > > > > (.text+0xae00): multiple definition of `rtl8192_setBBreg'
> > > > > drivers/staging/rtl8192u/built-in.o:(.text+0xa1a0): first defined here
> > > >
> > > > You built both of these drivers into the kernel, which causes the
> > > > problem. Try building them as modules, or just one as a module, and
> > > > that will solve the problem.
> > >
> > > We probably should create some Kconfig magic to prevent this situation?
> > >
> > > depends (othermodule != 'y') || (myself != 'y')
> > >
> > > or am I on the wrong track here?
> > >
> >
> > A simple
> >
> > depends on !OTHERMODULE
> >
> > allows either to be built-in or both to be modular.
> >
> > It also documents what conflicts.
> >
> > (see Menu dependencies in Documentation/kbuild/kconfig-language.txt)
>
> When added for 2 drivers that should not both be built-in, that
> causes this error message:
>
> drivers/staging/rtl8192u/Kconfig:1:error: recursive dependency detected!
> drivers/staging/rtl8192u/Kconfig:1: symbol RTL8192U depends on RTL8192E
> drivers/staging/rtl8192e/Kconfig:1: symbol RTL8192E depends on RTL8192U
>
> but yes, only one driver is then built-in.
Just make both drivers only able to be built as a module, which will
make everything work properly and all will be happy :)
thanks,
greg k-h
^ permalink raw reply
* [PATCH -next] staging: brcm80211 needs lots of delay.h
From: Randy Dunlap @ 2010-12-01 19:16 UTC (permalink / raw)
To: Stephen Rothwell, gregkh, driverdevel; +Cc: Dowan Kim, LKML, linux-next, akpm
In-Reply-To: <20101201133354.a7c198b1.sfr@canb.auug.org.au>
From: Randy Dunlap <randy.dunlap@oracle.com>
Fix lots of errors like:
drivers/staging/brcm80211/phy/wlc_phy_n.c:17613: error: implicit declaration of function 'mdelay'
drivers/staging/brcm80211/util/nicpci.c:246: error: implicit declaration of function 'udelay'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Henry Ptasinski <henryp@broadcom.com>
Cc: Dowan Kim <dowan@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
---
drivers/staging/brcm80211/phy/wlc_phy_cmn.c | 1 +
drivers/staging/brcm80211/phy/wlc_phy_lcn.c | 1 +
drivers/staging/brcm80211/phy/wlc_phy_n.c | 1 +
drivers/staging/brcm80211/util/aiutils.c | 1 +
drivers/staging/brcm80211/util/bcmotp.c | 1 +
drivers/staging/brcm80211/util/hndpmu.c | 1 +
drivers/staging/brcm80211/util/nicpci.c | 1 +
drivers/staging/brcm80211/util/siutils.c | 1 +
8 files changed, 8 insertions(+)
--- linux-next-20101201.orig/drivers/staging/brcm80211/phy/wlc_phy_n.c
+++ linux-next-20101201/drivers/staging/brcm80211/phy/wlc_phy_n.c
@@ -18,6 +18,7 @@
#include <linux/string.h>
#include <bcmdefs.h>
#include <wlc_cfg.h>
+#include <linux/delay.h>
#include <linux/pci.h>
#include <osl.h>
#include <siutils.h>
--- linux-next-20101201.orig/drivers/staging/brcm80211/util/nicpci.c
+++ linux-next-20101201/drivers/staging/brcm80211/util/nicpci.c
@@ -14,6 +14,7 @@
* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
+#include <linux/delay.h>
#include <linux/string.h>
#include <linux/pci.h>
#include <bcmdefs.h>
--- linux-next-20101201.orig/drivers/staging/brcm80211/util/siutils.c
+++ linux-next-20101201/drivers/staging/brcm80211/util/siutils.c
@@ -14,6 +14,7 @@
* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
+#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <bcmdefs.h>
--- linux-next-20101201.orig/drivers/staging/brcm80211/util/aiutils.c
+++ linux-next-20101201/drivers/staging/brcm80211/util/aiutils.c
@@ -14,6 +14,7 @@
* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
+#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <bcmdefs.h>
--- linux-next-20101201.orig/drivers/staging/brcm80211/util/bcmotp.c
+++ linux-next-20101201/drivers/staging/brcm80211/util/bcmotp.c
@@ -14,6 +14,7 @@
* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
+#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <bcmdefs.h>
--- linux-next-20101201.orig/drivers/staging/brcm80211/util/hndpmu.c
+++ linux-next-20101201/drivers/staging/brcm80211/util/hndpmu.c
@@ -13,6 +13,7 @@
* OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
* CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
+#include <linux/delay.h>
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/module.h>
--- linux-next-20101201.orig/drivers/staging/brcm80211/phy/wlc_phy_cmn.c
+++ linux-next-20101201/drivers/staging/brcm80211/phy/wlc_phy_cmn.c
@@ -20,6 +20,7 @@
#include <linux/string.h>
#include <bcmdefs.h>
#include <osl.h>
+#include <linux/delay.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <bcmendian.h>
--- linux-next-20101201.orig/drivers/staging/brcm80211/phy/wlc_phy_lcn.c
+++ linux-next-20101201/drivers/staging/brcm80211/phy/wlc_phy_lcn.c
@@ -17,6 +17,7 @@
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/bitops.h>
+#include <linux/delay.h>
#include <wlc_cfg.h>
#include <qmath.h>
#include <osl.h>
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox