[PATCH v5 2/3] phy: Move ULPI phy header out of drivers to include path

[PATCH v5 2/3] phy: Move ULPI phy header out of drivers to include path

[Vivek Gautam]

Although ULPI phy is currently being used by tusb1210,
there can be other consumers too in future. So move this
to the includes path for phy.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-usb@vger.kernel.org
---

Changes since v4:
 - None.

Changes since v3:
 - Removed qcom phy changes, since patch - 1/3 addressed that now.

Changes since v2:
 - Updated the location for this header in drivers using it.

 drivers/phy/phy-tusb1210.c                | 3 +--
 {drivers => include/linux}/phy/ulpi_phy.h | 0
 2 files changed, 1 insertion(+), 2 deletions(-)
 rename {drivers => include/linux}/phy/ulpi_phy.h (100%)

diff --git a/drivers/phy/phy-tusb1210.c b/drivers/phy/phy-tusb1210.c
index 4f6d5e71507d..bb3fb031c478 100644
--- a/drivers/phy/phy-tusb1210.c
+++ b/drivers/phy/phy-tusb1210.c
@@ -12,8 +12,7 @@
 #include <linux/module.h>
 #include <linux/ulpi/driver.h>
 #include <linux/gpio/consumer.h>
-
-#include "ulpi_phy.h"
+#include <linux/phy/ulpi_phy.h>
 
 #define TUSB1210_VENDOR_SPECIFIC2		0x80
 #define TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT	0
diff --git a/drivers/phy/ulpi_phy.h b/include/linux/phy/ulpi_phy.h
similarity index 100%
rename from drivers/phy/ulpi_phy.h
rename to include/linux/phy/ulpi_phy.h
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v5 2/3] phy: Move ULPI phy header out of drivers to include path

[Heikki Krogerus]

On Thu, May 11, 2017 at 12:17:41PM +0530, Vivek Gautam wrote:
> Although ULPI phy is currently being used by tusb1210,
> there can be other consumers too in future. So move this
> to the includes path for phy.
> 
> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
> Cc: Stephen Boyd <stephen.boyd@linaro.org>
> Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
> Cc: Kishon Vijay Abraham I <kishon@ti.com>
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-omap@vger.kernel.org
> Cc: linux-usb@vger.kernel.org
> ---

Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>

> Changes since v4:
>  - None.
> 
> Changes since v3:
>  - Removed qcom phy changes, since patch - 1/3 addressed that now.
> 
> Changes since v2:
>  - Updated the location for this header in drivers using it.
> 
>  drivers/phy/phy-tusb1210.c                | 3 +--
>  {drivers => include/linux}/phy/ulpi_phy.h | 0
>  2 files changed, 1 insertion(+), 2 deletions(-)
>  rename {drivers => include/linux}/phy/ulpi_phy.h (100%)
> 
> diff --git a/drivers/phy/phy-tusb1210.c b/drivers/phy/phy-tusb1210.c
> index 4f6d5e71507d..bb3fb031c478 100644
> --- a/drivers/phy/phy-tusb1210.c
> +++ b/drivers/phy/phy-tusb1210.c
> @@ -12,8 +12,7 @@
>  #include <linux/module.h>
>  #include <linux/ulpi/driver.h>
>  #include <linux/gpio/consumer.h>
> -
> -#include "ulpi_phy.h"
> +#include <linux/phy/ulpi_phy.h>
>  
>  #define TUSB1210_VENDOR_SPECIFIC2		0x80
>  #define TUSB1210_VENDOR_SPECIFIC2_IHSTX_SHIFT	0
> diff --git a/drivers/phy/ulpi_phy.h b/include/linux/phy/ulpi_phy.h
> similarity index 100%
> rename from drivers/phy/ulpi_phy.h
> rename to include/linux/phy/ulpi_phy.h
> -- 
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project

-- 
heikki

[PATCH v5 3/3] phy: Group vendor specific phy drivers

[Vivek Gautam]

Adding vendor specific directories in phy to group
phy drivers under their respective vendor umbrella.

Also updated the MAINTAINERS file to reflect the correct
directory structure for phy drivers.

Signed-off-by: Vivek Gautam <vivek.gautam-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Acked-by: Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>
Acked-by: Viresh Kumar <viresh.kumar-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Acked-by: Krzysztof Kozlowski <krzk-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
Reviewed-by: Jaehoon Chung <jh80.chung-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Cc: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
Cc: David S. Miller <davem-fT/PcQaiUtIeIZ0/mPfg9Q@public.gmane.org>
Cc: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
Cc: Guenter Roeck <linux-0h96xk9xTtrk1uMJSBkQmQ@public.gmane.org>
Cc: Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>
Cc: Viresh Kumar <viresh.kumar-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Cc: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
Cc: Sylwester Nawrocki <s.nawrocki-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Cc: Krzysztof Kozlowski <krzk-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Cc: Jaehoon Chung <jh80.chung-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Cc: Stephen Boyd <stephen.boyd-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Martin Blumenstingl <martin.blumenstingl-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: linux-arm-msm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Cc: linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
---

Changes since v4:
 - Reprepared the patch based on latest torvalds/master.
 - Added new directory for amlogic, since there's a new patch [1]
   coming in for amlogic platforms.

Changes since v3:
 - Added 'Acked-by' and 'Reviewed by' tags received for this patch.
 - No functional change.

Changes since v2:
 - Rebased on linux-phy/next.
 - Took care of drivers added/removed for each vendors since v2.
 - Updated the 'Signed-off-by' tag with my current email id.

Changes from v1:
 - Updated the MAINTAINERS file to reflect the same change
   in directory structure.
 - Removed PHY_PLAT config as pointed out by Kishon.
   So we don't require the second patch in the v1 of this series:
   [PATCH 2/2] arm: mach-spear: Enable PHY_PLAT to meet dependency
 - Renamed sunxi --> allwinner; rcar --> renesas.
 - Fixed error coming with qcom Makefile.

* Build tested multi_v7_defconfig.
* Build tested arm64 defconfig with all the involved configs enabled.

[1] https://patchwork.kernel.org/patch/9684303/

 MAINTAINERS                                        |  18 +-
 drivers/phy/Kconfig                                | 493 +--------------------
 drivers/phy/Makefile                               |  70 +--
 drivers/phy/allwinner/Kconfig                      |  31 ++
 drivers/phy/allwinner/Makefile                     |   2 +
 drivers/phy/{ => allwinner}/phy-sun4i-usb.c        |   0
 drivers/phy/{ => allwinner}/phy-sun9i-usb.c        |   0
 drivers/phy/amlogic/Kconfig                        |  14 +
 drivers/phy/amlogic/Makefile                       |   1 +
 drivers/phy/{ => amlogic}/phy-meson8b-usb2.c       |   0
 drivers/phy/broadcom/Kconfig                       |  55 +++
 drivers/phy/broadcom/Makefile                      |   6 +
 drivers/phy/{ => broadcom}/phy-bcm-cygnus-pcie.c   |   0
 drivers/phy/{ => broadcom}/phy-bcm-kona-usb2.c     |   0
 drivers/phy/{ => broadcom}/phy-bcm-ns-usb2.c       |   0
 drivers/phy/{ => broadcom}/phy-bcm-ns-usb3.c       |   0
 drivers/phy/{ => broadcom}/phy-bcm-ns2-pcie.c      |   0
 drivers/phy/{ => broadcom}/phy-brcm-sata.c         |   0
 drivers/phy/hisilicon/Kconfig                      |  20 +
 drivers/phy/hisilicon/Makefile                     |   2 +
 drivers/phy/{ => hisilicon}/phy-hi6220-usb.c       |   0
 drivers/phy/{ => hisilicon}/phy-hix5hd2-sata.c     |   0
 drivers/phy/marvell/Kconfig                        |  50 +++
 drivers/phy/marvell/Makefile                       |   6 +
 drivers/phy/{ => marvell}/phy-armada375-usb2.c     |   0
 drivers/phy/{ => marvell}/phy-berlin-sata.c        |   0
 drivers/phy/{ => marvell}/phy-berlin-usb.c         |   0
 drivers/phy/{ => marvell}/phy-mvebu-sata.c         |   0
 drivers/phy/{ => marvell}/phy-pxa-28nm-hsic.c      |   0
 drivers/phy/{ => marvell}/phy-pxa-28nm-usb2.c      |   0
 drivers/phy/qualcomm/Kconfig                       |  58 +++
 drivers/phy/qualcomm/Makefile                      |   9 +
 drivers/phy/{ => qualcomm}/phy-qcom-apq8064-sata.c |   0
 drivers/phy/{ => qualcomm}/phy-qcom-ipq806x-sata.c |   0
 drivers/phy/{ => qualcomm}/phy-qcom-qmp.c          |   0
 drivers/phy/{ => qualcomm}/phy-qcom-qusb2.c        |   0
 drivers/phy/{ => qualcomm}/phy-qcom-ufs-i.h        |   0
 drivers/phy/{ => qualcomm}/phy-qcom-ufs-qmp-14nm.c |   0
 drivers/phy/{ => qualcomm}/phy-qcom-ufs-qmp-14nm.h |   0
 drivers/phy/{ => qualcomm}/phy-qcom-ufs-qmp-20nm.c |   0
 drivers/phy/{ => qualcomm}/phy-qcom-ufs-qmp-20nm.h |   0
 drivers/phy/{ => qualcomm}/phy-qcom-ufs.c          |   0
 drivers/phy/{ => qualcomm}/phy-qcom-usb-hs.c       |   0
 drivers/phy/{ => qualcomm}/phy-qcom-usb-hsic.c     |   0
 drivers/phy/renesas/Kconfig                        |  17 +
 drivers/phy/renesas/Makefile                       |   2 +
 drivers/phy/{ => renesas}/phy-rcar-gen2.c          |   0
 drivers/phy/{ => renesas}/phy-rcar-gen3-usb2.c     |   0
 drivers/phy/rockchip/Kconfig                       |  51 +++
 drivers/phy/rockchip/Makefile                      |   6 +
 drivers/phy/{ => rockchip}/phy-rockchip-dp.c       |   0
 drivers/phy/{ => rockchip}/phy-rockchip-emmc.c     |   0
 .../phy/{ => rockchip}/phy-rockchip-inno-usb2.c    |   0
 drivers/phy/{ => rockchip}/phy-rockchip-pcie.c     |   0
 drivers/phy/{ => rockchip}/phy-rockchip-typec.c    |   0
 drivers/phy/{ => rockchip}/phy-rockchip-usb.c      |   0
 drivers/phy/samsung/Kconfig                        |  95 ++++
 drivers/phy/samsung/Makefile                       |  11 +
 drivers/phy/{ => samsung}/phy-exynos-dp-video.c    |   0
 drivers/phy/{ => samsung}/phy-exynos-mipi-video.c  |   0
 drivers/phy/{ => samsung}/phy-exynos-pcie.c        |   0
 drivers/phy/{ => samsung}/phy-exynos4210-usb2.c    |   0
 drivers/phy/{ => samsung}/phy-exynos4x12-usb2.c    |   0
 drivers/phy/{ => samsung}/phy-exynos5-usbdrd.c     |   0
 drivers/phy/{ => samsung}/phy-exynos5250-sata.c    |   0
 drivers/phy/{ => samsung}/phy-exynos5250-usb2.c    |   0
 drivers/phy/{ => samsung}/phy-s5pv210-usb2.c       |   0
 drivers/phy/{ => samsung}/phy-samsung-usb2.c       |   0
 drivers/phy/{ => samsung}/phy-samsung-usb2.h       |   0
 drivers/phy/st/Kconfig                             |  33 ++
 drivers/phy/st/Makefile                            |   4 +
 drivers/phy/{ => st}/phy-miphy28lp.c               |   0
 drivers/phy/{ => st}/phy-spear1310-miphy.c         |   0
 drivers/phy/{ => st}/phy-spear1340-miphy.c         |   0
 drivers/phy/{ => st}/phy-stih407-usb.c             |   0
 drivers/phy/ti/Kconfig                             |  78 ++++
 drivers/phy/ti/Makefile                            |   7 +
 drivers/phy/{ => ti}/phy-da8xx-usb.c               |   0
 drivers/phy/{ => ti}/phy-dm816x-usb.c              |   0
 drivers/phy/{ => ti}/phy-omap-control.c            |   0
 drivers/phy/{ => ti}/phy-omap-usb2.c               |   0
 drivers/phy/{ => ti}/phy-ti-pipe3.c                |   0
 drivers/phy/{ => ti}/phy-tusb1210.c                |   0
 drivers/phy/{ => ti}/phy-twl4030-usb.c             |   0
 84 files changed, 594 insertions(+), 545 deletions(-)
 create mode 100644 drivers/phy/allwinner/Kconfig
 create mode 100644 drivers/phy/allwinner/Makefile
 rename drivers/phy/{ => allwinner}/phy-sun4i-usb.c (100%)
 rename drivers/phy/{ => allwinner}/phy-sun9i-usb.c (100%)
 create mode 100644 drivers/phy/amlogic/Kconfig
 create mode 100644 drivers/phy/amlogic/Makefile
 rename drivers/phy/{ => amlogic}/phy-meson8b-usb2.c (100%)
 create mode 100644 drivers/phy/broadcom/Kconfig
 create mode 100644 drivers/phy/broadcom/Makefile
 rename drivers/phy/{ => broadcom}/phy-bcm-cygnus-pcie.c (100%)
 rename drivers/phy/{ => broadcom}/phy-bcm-kona-usb2.c (100%)
 rename drivers/phy/{ => broadcom}/phy-bcm-ns-usb2.c (100%)
 rename drivers/phy/{ => broadcom}/phy-bcm-ns-usb3.c (100%)
 rename drivers/phy/{ => broadcom}/phy-bcm-ns2-pcie.c (100%)
 rename drivers/phy/{ => broadcom}/phy-brcm-sata.c (100%)
 create mode 100644 drivers/phy/hisilicon/Kconfig
 create mode 100644 drivers/phy/hisilicon/Makefile
 rename drivers/phy/{ => hisilicon}/phy-hi6220-usb.c (100%)
 rename drivers/phy/{ => hisilicon}/phy-hix5hd2-sata.c (100%)
 create mode 100644 drivers/phy/marvell/Kconfig
 create mode 100644 drivers/phy/marvell/Makefile
 rename drivers/phy/{ => marvell}/phy-armada375-usb2.c (100%)
 rename drivers/phy/{ => marvell}/phy-berlin-sata.c (100%)
 rename drivers/phy/{ => marvell}/phy-berlin-usb.c (100%)
 rename drivers/phy/{ => marvell}/phy-mvebu-sata.c (100%)
 rename drivers/phy/{ => marvell}/phy-pxa-28nm-hsic.c (100%)
 rename drivers/phy/{ => marvell}/phy-pxa-28nm-usb2.c (100%)
 create mode 100644 drivers/phy/qualcomm/Kconfig
 create mode 100644 drivers/phy/qualcomm/Makefile
 rename drivers/phy/{ => qualcomm}/phy-qcom-apq8064-sata.c (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-ipq806x-sata.c (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-qmp.c (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-qusb2.c (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-ufs-i.h (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-ufs-qmp-14nm.c (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-ufs-qmp-14nm.h (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-ufs-qmp-20nm.c (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-ufs-qmp-20nm.h (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-ufs.c (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-usb-hs.c (100%)
 rename drivers/phy/{ => qualcomm}/phy-qcom-usb-hsic.c (100%)
 create mode 100644 drivers/phy/renesas/Kconfig
 create mode 100644 drivers/phy/renesas/Makefile
 rename drivers/phy/{ => renesas}/phy-rcar-gen2.c (100%)
 rename drivers/phy/{ => renesas}/phy-rcar-gen3-usb2.c (100%)
 create mode 100644 drivers/phy/rockchip/Kconfig
 create mode 100644 drivers/phy/rockchip/Makefile
 rename drivers/phy/{ => rockchip}/phy-rockchip-dp.c (100%)
 rename drivers/phy/{ => rockchip}/phy-rockchip-emmc.c (100%)
 rename drivers/phy/{ => rockchip}/phy-rockchip-inno-usb2.c (100%)
 rename drivers/phy/{ => rockchip}/phy-rockchip-pcie.c (100%)
 rename drivers/phy/{ => rockchip}/phy-rockchip-typec.c (100%)
 rename drivers/phy/{ => rockchip}/phy-rockchip-usb.c (100%)
 create mode 100644 drivers/phy/samsung/Kconfig
 create mode 100644 drivers/phy/samsung/Makefile
 rename drivers/phy/{ => samsung}/phy-exynos-dp-video.c (100%)
 rename drivers/phy/{ => samsung}/phy-exynos-mipi-video.c (100%)
 rename drivers/phy/{ => samsung}/phy-exynos-pcie.c (100%)
 rename drivers/phy/{ => samsung}/phy-exynos4210-usb2.c (100%)
 rename drivers/phy/{ => samsung}/phy-exynos4x12-usb2.c (100%)
 rename drivers/phy/{ => samsung}/phy-exynos5-usbdrd.c (100%)
 rename drivers/phy/{ => samsung}/phy-exynos5250-sata.c (100%)
 rename drivers/phy/{ => samsung}/phy-exynos5250-usb2.c (100%)
 rename drivers/phy/{ => samsung}/phy-s5pv210-usb2.c (100%)
 rename drivers/phy/{ => samsung}/phy-samsung-usb2.c (100%)
 rename drivers/phy/{ => samsung}/phy-samsung-usb2.h (100%)
 create mode 100644 drivers/phy/st/Kconfig
 create mode 100644 drivers/phy/st/Makefile
 rename drivers/phy/{ => st}/phy-miphy28lp.c (100%)
 rename drivers/phy/{ => st}/phy-spear1310-miphy.c (100%)
 rename drivers/phy/{ => st}/phy-spear1340-miphy.c (100%)
 rename drivers/phy/{ => st}/phy-stih407-usb.c (100%)
 create mode 100644 drivers/phy/ti/Kconfig
 create mode 100644 drivers/phy/ti/Makefile
 rename drivers/phy/{ => ti}/phy-da8xx-usb.c (100%)
 rename drivers/phy/{ => ti}/phy-dm816x-usb.c (100%)
 rename drivers/phy/{ => ti}/phy-omap-control.c (100%)
 rename drivers/phy/{ => ti}/phy-omap-usb2.c (100%)
 rename drivers/phy/{ => ti}/phy-ti-pipe3.c (100%)
 rename drivers/phy/{ => ti}/phy-tusb1210.c (100%)
 rename drivers/phy/{ => ti}/phy-twl4030-usb.c (100%)

diff --git a/MAINTAINERS b/MAINTAINERS
index a4a9e31fed72..4550abed3b93 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1825,8 +1825,8 @@ F:	drivers/i2c/busses/i2c-st.c
 F:	drivers/media/rc/st_rc.c
 F:	drivers/media/platform/sti/c8sectpfe/
 F:	drivers/mmc/host/sdhci-st.c
-F:	drivers/phy/phy-miphy28lp.c
-F:	drivers/phy/phy-stih407-usb.c
+F:	drivers/phy/st/phy-miphy28lp.c
+F:	drivers/phy/st/phy-stih407-usb.c
 F:	drivers/pinctrl/pinctrl-st.c
 F:	drivers/remoteproc/st_remoteproc.c
 F:	drivers/remoteproc/st_slim_rproc.c
@@ -10810,7 +10810,7 @@ RENESAS USB2 PHY DRIVER
 M:	Yoshihiro Shimoda <yoshihiro.shimoda.uh-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
 L:	linux-renesas-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
 S:	Maintained
-F:	drivers/phy/phy-rcar-gen3-usb2.c
+F:	drivers/phy/renesas/phy-rcar-gen3-usb2.c
 
 RESET CONTROLLER FRAMEWORK
 M:	Philipp Zabel <p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
@@ -11212,12 +11212,12 @@ L:	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
 S:	Supported
 F:	Documentation/devicetree/bindings/phy/samsung-phy.txt
 F:	Documentation/phy/samsung-usb2.txt
-F:	drivers/phy/phy-exynos4210-usb2.c
-F:	drivers/phy/phy-exynos4x12-usb2.c
-F:	drivers/phy/phy-exynos5250-usb2.c
-F:	drivers/phy/phy-s5pv210-usb2.c
-F:	drivers/phy/phy-samsung-usb2.c
-F:	drivers/phy/phy-samsung-usb2.h
+F:	drivers/phy/samsung/phy-exynos4210-usb2.c
+F:	drivers/phy/samsung/phy-exynos4x12-usb2.c
+F:	drivers/phy/samsung/phy-exynos5250-usb2.c
+F:	drivers/phy/samsung/phy-s5pv210-usb2.c
+F:	drivers/phy/samsung/phy-samsung-usb2.c
+F:	drivers/phy/samsung/phy-samsung-usb2.h
 
 SERIAL DRIVERS
 M:	Greg Kroah-Hartman <gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org>
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index afaf7b643eeb..b353ac603ea0 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -15,73 +15,6 @@ config GENERIC_PHY
 	  phy users can obtain reference to the PHY. All the users of this
 	  framework should select this config.
 
-config PHY_BCM_NS_USB2
-	tristate "Broadcom Northstar USB 2.0 PHY Driver"
-	depends on ARCH_BCM_IPROC || COMPILE_TEST
-	depends on HAS_IOMEM && OF
-	select GENERIC_PHY
-	help
-	  Enable this to support Broadcom USB 2.0 PHY connected to the USB
-	  controller on Northstar family.
-
-config PHY_BCM_NS_USB3
-	tristate "Broadcom Northstar USB 3.0 PHY Driver"
-	depends on ARCH_BCM_IPROC || COMPILE_TEST
-	depends on HAS_IOMEM && OF
-	select GENERIC_PHY
-	help
-	  Enable this to support Broadcom USB 3.0 PHY connected to the USB
-	  controller on Northstar family.
-
-config PHY_BERLIN_USB
-	tristate "Marvell Berlin USB PHY Driver"
-	depends on ARCH_BERLIN && RESET_CONTROLLER && HAS_IOMEM && OF
-	select GENERIC_PHY
-	help
-	  Enable this to support the USB PHY on Marvell Berlin SoCs.
-
-config PHY_BERLIN_SATA
-	tristate "Marvell Berlin SATA PHY driver"
-	depends on ARCH_BERLIN && HAS_IOMEM && OF
-	select GENERIC_PHY
-	help
-	  Enable this to support the SATA PHY on Marvell Berlin SoCs.
-
-config ARMADA375_USBCLUSTER_PHY
-	def_bool y
-	depends on MACH_ARMADA_375 || COMPILE_TEST
-	depends on OF && HAS_IOMEM
-	select GENERIC_PHY
-
-config PHY_DA8XX_USB
-	tristate "TI DA8xx USB PHY Driver"
-	depends on ARCH_DAVINCI_DA8XX
-	select GENERIC_PHY
-	select MFD_SYSCON
-	help
-	  Enable this to support the USB PHY on DA8xx SoCs.
-
-	  This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
-
-config PHY_DM816X_USB
-	tristate "TI dm816x USB PHY driver"
-	depends on ARCH_OMAP2PLUS
-	depends on USB_SUPPORT
-	select GENERIC_PHY
-	select USB_PHY
-	help
-	  Enable this for dm816x USB to work.
-
-config PHY_EXYNOS_MIPI_VIDEO
-	tristate "S5P/EXYNOS SoC series MIPI CSI-2/DSI PHY driver"
-	depends on HAS_IOMEM
-	depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
-	select GENERIC_PHY
-	default y if ARCH_S5PV210 || ARCH_EXYNOS
-	help
-	  Support for MIPI CSI-2 and MIPI DSI DPHY found on Samsung S5P
-	  and EXYNOS SoCs.
-
 config PHY_LPC18XX_USB_OTG
 	tristate "NXP LPC18xx/43xx SoC USB OTG PHY driver"
 	depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
@@ -93,146 +26,6 @@ config PHY_LPC18XX_USB_OTG
 	  This driver is need for USB0 support on LPC18xx/43xx and takes
 	  care of enabling and clock setup.
 
-config PHY_PXA_28NM_HSIC
-	tristate "Marvell USB HSIC 28nm PHY Driver"
-	depends on HAS_IOMEM
-	select GENERIC_PHY
-	help
-	  Enable this to support Marvell USB HSIC PHY driver for Marvell
-	  SoC. This driver will do the PHY initialization and shutdown.
-	  The PHY driver will be used by Marvell ehci driver.
-
-	  To compile this driver as a module, choose M here.
-
-config PHY_PXA_28NM_USB2
-	tristate "Marvell USB 2.0 28nm PHY Driver"
-	depends on HAS_IOMEM
-	select GENERIC_PHY
-	help
-	  Enable this to support Marvell USB 2.0 PHY driver for Marvell
-	  SoC. This driver will do the PHY initialization and shutdown.
-	  The PHY driver will be used by Marvell udc/ehci/otg driver.
-
-	  To compile this driver as a module, choose M here.
-
-config PHY_MVEBU_SATA
-	def_bool y
-	depends on ARCH_DOVE || MACH_DOVE || MACH_KIRKWOOD
-	depends on OF
-	select GENERIC_PHY
-
-config PHY_MIPHY28LP
-	tristate "STMicroelectronics MIPHY28LP PHY driver for STiH407"
-	depends on ARCH_STI
-	select GENERIC_PHY
-	help
-	  Enable this to support the miphy transceiver (for SATA/PCIE/USB3)
-	  that is part of STMicroelectronics STiH407 SoC.
-
-config PHY_RCAR_GEN2
-	tristate "Renesas R-Car generation 2 USB PHY driver"
-	depends on ARCH_RENESAS
-	depends on GENERIC_PHY
-	help
-	  Support for USB PHY found on Renesas R-Car generation 2 SoCs.
-
-config PHY_RCAR_GEN3_USB2
-	tristate "Renesas R-Car generation 3 USB 2.0 PHY driver"
-	depends on ARCH_RENESAS
-	depends on EXTCON
-	select GENERIC_PHY
-	help
-	  Support for USB 2.0 PHY found on Renesas R-Car generation 3 SoCs.
-
-config OMAP_CONTROL_PHY
-	tristate "OMAP CONTROL PHY Driver"
-	depends on ARCH_OMAP2PLUS || COMPILE_TEST
-	help
-	  Enable this to add support for the PHY part present in the control
-	  module. This driver has API to power on the USB2 PHY and to write to
-	  the mailbox. The mailbox is present only in omap4 and the register to
-	  power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
-	  additional register to power on USB3 PHY/SATA PHY/PCIE PHY
-	  (PIPE3 PHY).
-
-config OMAP_USB2
-	tristate "OMAP USB2 PHY Driver"
-	depends on ARCH_OMAP2PLUS
-	depends on USB_SUPPORT
-	select GENERIC_PHY
-	select USB_PHY
-	select OMAP_CONTROL_PHY
-	depends on OMAP_OCP2SCP
-	help
-	  Enable this to support the transceiver that is part of SOC. This
-	  driver takes care of all the PHY functionality apart from comparator.
-	  The USB OTG controller communicates with the comparator using this
-	  driver.
-
-config TI_PIPE3
-	tristate "TI PIPE3 PHY Driver"
-	depends on ARCH_OMAP2PLUS || COMPILE_TEST
-	select GENERIC_PHY
-	select OMAP_CONTROL_PHY
-	depends on OMAP_OCP2SCP
-	help
-	  Enable this to support the PIPE3 PHY that is part of TI SOCs. This
-	  driver takes care of all the PHY functionality apart from comparator.
-	  This driver interacts with the "OMAP Control PHY Driver" to power
-	  on/off the PHY.
-
-config TWL4030_USB
-	tristate "TWL4030 USB Transceiver Driver"
-	depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
-	depends on USB_SUPPORT
-	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y'
-	select GENERIC_PHY
-	select USB_PHY
-	help
-	  Enable this to support the USB OTG transceiver on TWL4030
-	  family chips (including the TWL5030 and TPS659x0 devices).
-	  This transceiver supports high and full speed devices plus,
-	  in host mode, low speed.
-
-config PHY_EXYNOS_DP_VIDEO
-	tristate "EXYNOS SoC series Display Port PHY driver"
-	depends on OF
-	depends on ARCH_EXYNOS || COMPILE_TEST
-	default ARCH_EXYNOS
-	select GENERIC_PHY
-	help
-	  Support for Display Port PHY found on Samsung EXYNOS SoCs.
-
-config BCM_KONA_USB2_PHY
-	tristate "Broadcom Kona USB2 PHY Driver"
-	depends on HAS_IOMEM
-	select GENERIC_PHY
-	help
-	  Enable this to support the Broadcom Kona USB 2.0 PHY.
-
-config PHY_EXYNOS5250_SATA
-	tristate "Exynos5250 Sata SerDes/PHY driver"
-	depends on SOC_EXYNOS5250
-	depends on HAS_IOMEM
-	depends on OF
-	select GENERIC_PHY
-	select I2C
-	select I2C_S3C2410
-	select MFD_SYSCON
-	help
-	  Enable this to support SATA SerDes/Phy found on Samsung's
-	  Exynos5250 based SoCs.This SerDes/Phy supports SATA 1.5 Gb/s,
-	  SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds. It supports one SATA host
-	  port to accept one SATA device.
-
-config PHY_HIX5HD2_SATA
-	tristate "HIX5HD2 SATA PHY Driver"
-	depends on ARCH_HIX5HD2 && OF && HAS_IOMEM
-	select GENERIC_PHY
-	select MFD_SYSCON
-	help
-	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
-
 config PHY_MT65XX_USB3
 	tristate "Mediatek USB3.0 PHY Driver"
 	depends on ARCH_MEDIATEK && OF
@@ -241,104 +34,6 @@ config PHY_MT65XX_USB3
 	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver,
 	  it supports multiple usb2.0 and usb3.0 ports.
 
-config PHY_HI6220_USB
-	tristate "hi6220 USB PHY support"
-	depends on (ARCH_HISI && ARM64) || COMPILE_TEST
-	select GENERIC_PHY
-	select MFD_SYSCON
-	help
-	  Enable this to support the HISILICON HI6220 USB PHY.
-
-	  To compile this driver as a module, choose M here.
-
-config PHY_SUN4I_USB
-	tristate "Allwinner sunxi SoC USB PHY driver"
-	depends on ARCH_SUNXI && HAS_IOMEM && OF
-	depends on RESET_CONTROLLER
-	depends on EXTCON
-	depends on POWER_SUPPLY
-	depends on USB_SUPPORT
-	select GENERIC_PHY
-	select USB_COMMON
-	help
-	  Enable this to support the transceiver that is part of Allwinner
-	  sunxi SoCs.
-
-	  This driver controls the entire USB PHY block, both the USB OTG
-	  parts, as well as the 2 regular USB 2 host PHYs.
-
-config PHY_SUN9I_USB
-	tristate "Allwinner sun9i SoC USB PHY driver"
-	depends on ARCH_SUNXI && HAS_IOMEM && OF
-	depends on RESET_CONTROLLER
-	depends on USB_SUPPORT
-	select USB_COMMON
-	select GENERIC_PHY
-	help
-	  Enable this to support the transceiver that is part of Allwinner
-	  sun9i SoCs.
-
-	  This driver controls each individual USB 2 host PHY.
-
-config PHY_SAMSUNG_USB2
-	tristate "Samsung USB 2.0 PHY driver"
-	depends on HAS_IOMEM
-	depends on USB_EHCI_EXYNOS || USB_OHCI_EXYNOS || USB_DWC2
-	select GENERIC_PHY
-	select MFD_SYSCON
-	default ARCH_EXYNOS
-	help
-	  Enable this to support the Samsung USB 2.0 PHY driver for Samsung
-	  SoCs. This driver provides the interface for USB 2.0 PHY. Support
-	  for particular PHYs will be enabled based on the SoC type in addition
-	  to this driver.
-
-config PHY_S5PV210_USB2
-	bool "Support for S5PV210"
-	depends on PHY_SAMSUNG_USB2
-	depends on ARCH_S5PV210
-	help
-	  Enable USB PHY support for S5PV210. This option requires that Samsung
-	  USB 2.0 PHY driver is enabled and means that support for this
-	  particular SoC is compiled in the driver. In case of S5PV210 two phys
-	  are available - device and host.
-
-config PHY_EXYNOS4210_USB2
-	bool
-	depends on PHY_SAMSUNG_USB2
-	default CPU_EXYNOS4210
-
-config PHY_EXYNOS4X12_USB2
-	bool
-	depends on PHY_SAMSUNG_USB2
-	default SOC_EXYNOS3250 || SOC_EXYNOS4212 || SOC_EXYNOS4412
-
-config PHY_EXYNOS5250_USB2
-	bool
-	depends on PHY_SAMSUNG_USB2
-	default SOC_EXYNOS5250 || SOC_EXYNOS5420
-
-config PHY_EXYNOS5_USBDRD
-	tristate "Exynos5 SoC series USB DRD PHY driver"
-	depends on ARCH_EXYNOS && OF
-	depends on HAS_IOMEM
-	depends on USB_DWC3_EXYNOS
-	select GENERIC_PHY
-	select MFD_SYSCON
-	default y
-	help
-	  Enable USB DRD PHY support for Exynos 5 SoC series.
-	  This driver provides PHY interface for USB 3.0 DRD controller
-	  present on Exynos5 SoC series.
-
-config PHY_EXYNOS_PCIE
-	bool "Exynos PCIe PHY driver"
-	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
-	select GENERIC_PHY
-	help
-	  Enable PCIe PHY support for Exynos SoC series.
-	  This driver provides PHY interface for Exynos PCIe controller.
-
 config PHY_PISTACHIO_USB
 	tristate "IMG Pistachio USB2.0 PHY driver"
 	depends on MACH_PISTACHIO
@@ -346,83 +41,6 @@ config PHY_PISTACHIO_USB
 	help
 	  Enable this to support the USB2.0 PHY on the IMG Pistachio SoC.
 
-config PHY_QCOM_APQ8064_SATA
-	tristate "Qualcomm APQ8064 SATA SerDes/PHY driver"
-	depends on ARCH_QCOM
-	depends on HAS_IOMEM
-	depends on OF
-	select GENERIC_PHY
-
-config PHY_QCOM_IPQ806X_SATA
-	tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
-	depends on ARCH_QCOM
-	depends on HAS_IOMEM
-	depends on OF
-	select GENERIC_PHY
-
-config PHY_ROCKCHIP_USB
-	tristate "Rockchip USB2 PHY Driver"
-	depends on ARCH_ROCKCHIP && OF
-	select GENERIC_PHY
-	help
-	  Enable this to support the Rockchip USB 2.0 PHY.
-
-config PHY_ROCKCHIP_INNO_USB2
-	tristate "Rockchip INNO USB2PHY Driver"
-	depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF
-	depends on COMMON_CLK
-	depends on EXTCON
-	depends on USB_SUPPORT
-	select GENERIC_PHY
-	select USB_COMMON
-	help
-	  Support for Rockchip USB2.0 PHY with Innosilicon IP block.
-
-config PHY_ROCKCHIP_EMMC
-	tristate "Rockchip EMMC PHY Driver"
-	depends on ARCH_ROCKCHIP && OF
-	select GENERIC_PHY
-	help
-	  Enable this to support the Rockchip EMMC PHY.
-
-config PHY_ROCKCHIP_DP
-	tristate "Rockchip Display Port PHY Driver"
-	depends on ARCH_ROCKCHIP && OF
-	select GENERIC_PHY
-	help
-	  Enable this to support the Rockchip Display Port PHY.
-
-config PHY_ROCKCHIP_PCIE
-	tristate "Rockchip PCIe PHY Driver"
-	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
-	select GENERIC_PHY
-	select MFD_SYSCON
-	help
-	  Enable this to support the Rockchip PCIe PHY.
-
-config PHY_ROCKCHIP_TYPEC
-	tristate "Rockchip TYPEC PHY Driver"
-	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
-	select EXTCON
-	select GENERIC_PHY
-	select RESET_CONTROLLER
-	help
-	  Enable this to support the Rockchip USB TYPEC PHY.
-
-config PHY_ST_SPEAR1310_MIPHY
-	tristate "ST SPEAR1310-MIPHY driver"
-	select GENERIC_PHY
-	depends on MACH_SPEAR1310 || COMPILE_TEST
-	help
-	  Support for ST SPEAr1310 MIPHY which can be used for PCIe and SATA.
-
-config PHY_ST_SPEAR1340_MIPHY
-	tristate "ST SPEAR1340-MIPHY driver"
-	select GENERIC_PHY
-	depends on MACH_SPEAR1340 || COMPILE_TEST
-	help
-	  Support for ST SPEAr1340 MIPHY which can be used for PCIe and SATA.
-
 config PHY_XGENE
 	tristate "APM X-Gene 15Gbps PHY support"
 	depends on HAS_IOMEM && OF && (ARM64 || COMPILE_TEST)
@@ -430,104 +48,21 @@ config PHY_XGENE
 	help
 	  This option enables support for APM X-Gene SoC multi-purpose PHY.
 
-config PHY_STIH407_USB
-	tristate "STMicroelectronics USB2 picoPHY driver for STiH407 family"
-	depends on RESET_CONTROLLER
-	depends on ARCH_STI || COMPILE_TEST
-	select GENERIC_PHY
-	help
-	  Enable this support to enable the picoPHY device used by USB2
-	  and USB3 controllers on STMicroelectronics STiH407 SoC families.
-
-config PHY_QCOM_QMP
-	tristate "Qualcomm QMP PHY Driver"
-	depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST)
-	select GENERIC_PHY
-	help
-	  Enable this to support the QMP PHY transceiver that is used
-	  with controllers such as PCIe, UFS, and USB on Qualcomm chips.
-
-config PHY_QCOM_QUSB2
-	tristate "Qualcomm QUSB2 PHY Driver"
-	depends on OF && (ARCH_QCOM || COMPILE_TEST)
-	depends on NVMEM || !NVMEM
-	select GENERIC_PHY
-	help
-	  Enable this to support the HighSpeed QUSB2 PHY transceiver for USB
-	  controllers on Qualcomm chips. This driver supports the high-speed
-	  PHY which is usually paired with either the ChipIdea or Synopsys DWC3
-	  USB IPs on MSM SOCs.
-
-config PHY_QCOM_UFS
-	tristate "Qualcomm UFS PHY driver"
-	depends on OF && ARCH_QCOM
-	select GENERIC_PHY
-	help
-	  Support for UFS PHY on QCOM chipsets.
-
-config PHY_QCOM_USB_HS
-	tristate "Qualcomm USB HS PHY module"
-	depends on USB_ULPI_BUS
-	depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
-	select GENERIC_PHY
-	help
-	  Support for the USB high-speed ULPI compliant phy on Qualcomm
-	  chipsets.
-
-config PHY_QCOM_USB_HSIC
-	tristate "Qualcomm USB HSIC ULPI PHY module"
-	depends on USB_ULPI_BUS
-	select GENERIC_PHY
-	help
-	  Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
-
-config PHY_TUSB1210
-	tristate "TI TUSB1210 ULPI PHY module"
-	depends on USB_ULPI_BUS
-	select GENERIC_PHY
-	help
-	  Support for TI TUSB1210 USB ULPI PHY.
-
-config PHY_BRCM_SATA
-	tristate "Broadcom SATA PHY driver"
-	depends on ARCH_BRCMSTB || ARCH_BCM_IPROC || BMIPS_GENERIC || COMPILE_TEST
-	depends on OF
-	select GENERIC_PHY
-	default ARCH_BCM_IPROC
-	help
-	  Enable this to support the Broadcom SATA PHY.
-	  If unsure, say N.
-
-config PHY_CYGNUS_PCIE
-	tristate "Broadcom Cygnus PCIe PHY driver"
-	depends on OF && (ARCH_BCM_CYGNUS || COMPILE_TEST)
-	select GENERIC_PHY
-	default ARCH_BCM_CYGNUS
-	help
-	  Enable this to support the Broadcom Cygnus PCIe PHY.
-	  If unsure, say N.
-
+menu "Platform Phy drivers"
+
+source "drivers/phy/allwinner/Kconfig"
+source "drivers/phy/amlogic/Kconfig"
+source "drivers/phy/broadcom/Kconfig"
+source "drivers/phy/hisilicon/Kconfig"
+source "drivers/phy/marvell/Kconfig"
+source "drivers/phy/qualcomm/Kconfig"
+source "drivers/phy/renesas/Kconfig"
+source "drivers/phy/rockchip/Kconfig"
+source "drivers/phy/samsung/Kconfig"
+source "drivers/phy/st/Kconfig"
 source "drivers/phy/tegra/Kconfig"
+source "drivers/phy/ti/Kconfig"
 
-config PHY_NS2_PCIE
-	tristate "Broadcom Northstar2 PCIe PHY driver"
-	depends on OF && MDIO_BUS_MUX_BCM_IPROC
-	select GENERIC_PHY
-	default ARCH_BCM_IPROC
-	help
-	  Enable this to support the Broadcom Northstar2 PCIe PHY.
-	  If unsure, say N.
-
-config PHY_MESON8B_USB2
-	tristate "Meson8b and GXBB USB2 PHY driver"
-	default ARCH_MESON
-	depends on OF && (ARCH_MESON || COMPILE_TEST)
-	depends on USB_SUPPORT
-	select USB_COMMON
-	select GENERIC_PHY
-	help
-	  Enable this to support the Meson USB2 PHYs found in Meson8b
-	  and GXBB SoCs.
-	  If unsure, say N.
+endmenu
 
 endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index f8047b4639fa..c1bd1fa3c853 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -3,64 +3,20 @@
 #
 
 obj-$(CONFIG_GENERIC_PHY)		+= phy-core.o
-obj-$(CONFIG_PHY_BCM_NS_USB2)		+= phy-bcm-ns-usb2.o
-obj-$(CONFIG_PHY_BCM_NS_USB3)		+= phy-bcm-ns-usb3.o
-obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
-obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
-obj-$(CONFIG_PHY_DA8XX_USB)		+= phy-da8xx-usb.o
-obj-$(CONFIG_PHY_DM816X_USB)		+= phy-dm816x-usb.o
-obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
-obj-$(CONFIG_BCM_KONA_USB2_PHY)		+= phy-bcm-kona-usb2.o
-obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
-obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
 obj-$(CONFIG_PHY_LPC18XX_USB_OTG)	+= phy-lpc18xx-usb-otg.o
-obj-$(CONFIG_PHY_PXA_28NM_USB2)		+= phy-pxa-28nm-usb2.o
-obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
-obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
-obj-$(CONFIG_PHY_MIPHY28LP) 		+= phy-miphy28lp.o
-obj-$(CONFIG_PHY_RCAR_GEN2)		+= phy-rcar-gen2.o
-obj-$(CONFIG_PHY_RCAR_GEN3_USB2)	+= phy-rcar-gen3-usb2.o
-obj-$(CONFIG_OMAP_CONTROL_PHY)		+= phy-omap-control.o
-obj-$(CONFIG_OMAP_USB2)			+= phy-omap-usb2.o
-obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
-obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
-obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
-obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
-obj-$(CONFIG_PHY_HI6220_USB)		+= phy-hi6220-usb.o
 obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
-obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
-obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
-obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
-phy-exynos-usb2-y			+= phy-samsung-usb2.o
-phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
-phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
-phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
-phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
-obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
-obj-$(CONFIG_PHY_EXYNOS_PCIE)	+= phy-exynos-pcie.o
-obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
-obj-$(CONFIG_PHY_ROCKCHIP_USB) += phy-rockchip-usb.o
-obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
-obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
-obj-$(CONFIG_PHY_ROCKCHIP_PCIE) += phy-rockchip-pcie.o
-obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
-obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o
-obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
-obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
-obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
 obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
-obj-$(CONFIG_PHY_STIH407_USB)		+= phy-stih407-usb.o
-obj-$(CONFIG_PHY_QCOM_QMP)		+= phy-qcom-qmp.o
-obj-$(CONFIG_PHY_QCOM_QUSB2)		+= phy-qcom-qusb2.o
-obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs.o
-obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-20nm.o
-obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-14nm.o
-obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
-obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
-obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
-obj-$(CONFIG_PHY_BRCM_SATA)		+= phy-brcm-sata.o
 obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
-obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
-obj-$(CONFIG_ARCH_TEGRA) += tegra/
-obj-$(CONFIG_PHY_NS2_PCIE)		+= phy-bcm-ns2-pcie.o
-obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
+
+obj-$(CONFIG_ARCH_SUNXI)		+= allwinner/
+obj-$(CONFIG_ARCH_MESON)		+= amlogic/
+obj-$(CONFIG_ARCH_RENESAS)		+= renesas/
+obj-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip/
+obj-$(CONFIG_ARCH_TEGRA)		+= tegra/
+obj-y					+= broadcom/	\
+					   hisilicon/	\
+					   marvell/	\
+					   qualcomm/	\
+					   samsung/	\
+					   st/		\
+					   ti/
diff --git a/drivers/phy/allwinner/Kconfig b/drivers/phy/allwinner/Kconfig
new file mode 100644
index 000000000000..cdc1e745ba47
--- /dev/null
+++ b/drivers/phy/allwinner/Kconfig
@@ -0,0 +1,31 @@
+#
+# Phy drivers for Allwinner platforms
+#
+config PHY_SUN4I_USB
+	tristate "Allwinner sunxi SoC USB PHY driver"
+	depends on ARCH_SUNXI && HAS_IOMEM && OF
+	depends on RESET_CONTROLLER
+	depends on EXTCON
+	depends on POWER_SUPPLY
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_COMMON
+	help
+	  Enable this to support the transceiver that is part of Allwinner
+	  sunxi SoCs.
+
+	  This driver controls the entire USB PHY block, both the USB OTG
+	  parts, as well as the 2 regular USB 2 host PHYs.
+
+config PHY_SUN9I_USB
+	tristate "Allwinner sun9i SoC USB PHY driver"
+	depends on ARCH_SUNXI && HAS_IOMEM && OF
+	depends on RESET_CONTROLLER
+	depends on USB_SUPPORT
+	select USB_COMMON
+	select GENERIC_PHY
+	help
+	  Enable this to support the transceiver that is part of Allwinner
+	  sun9i SoCs.
+
+	  This driver controls each individual USB 2 host PHY.
diff --git a/drivers/phy/allwinner/Makefile b/drivers/phy/allwinner/Makefile
new file mode 100644
index 000000000000..8605529c01a1
--- /dev/null
+++ b/drivers/phy/allwinner/Makefile
@@ -0,0 +1,2 @@
+obj-$(CONFIG_PHY_SUN4I_USB)		+= phy-sun4i-usb.o
+obj-$(CONFIG_PHY_SUN9I_USB)		+= phy-sun9i-usb.o
diff --git a/drivers/phy/phy-sun4i-usb.c b/drivers/phy/allwinner/phy-sun4i-usb.c
similarity index 100%
rename from drivers/phy/phy-sun4i-usb.c
rename to drivers/phy/allwinner/phy-sun4i-usb.c
diff --git a/drivers/phy/phy-sun9i-usb.c b/drivers/phy/allwinner/phy-sun9i-usb.c
similarity index 100%
rename from drivers/phy/phy-sun9i-usb.c
rename to drivers/phy/allwinner/phy-sun9i-usb.c
diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
new file mode 100644
index 000000000000..edcd5b65179f
--- /dev/null
+++ b/drivers/phy/amlogic/Kconfig
@@ -0,0 +1,14 @@
+#
+# Phy drivers for Amlogic platforms
+#
+config PHY_MESON8B_USB2
+	tristate "Meson8b and GXBB USB2 PHY driver"
+	default ARCH_MESON
+	depends on OF && (ARCH_MESON || COMPILE_TEST)
+	depends on USB_SUPPORT
+	select USB_COMMON
+	select GENERIC_PHY
+	help
+	  Enable this to support the Meson USB2 PHYs found in Meson8b
+	  and GXBB SoCs.
+	  If unsure, say N.
diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
new file mode 100644
index 000000000000..47b6eecc3864
--- /dev/null
+++ b/drivers/phy/amlogic/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_PHY_MESON8B_USB2)		+= phy-meson8b-usb2.o
diff --git a/drivers/phy/phy-meson8b-usb2.c b/drivers/phy/amlogic/phy-meson8b-usb2.c
similarity index 100%
rename from drivers/phy/phy-meson8b-usb2.c
rename to drivers/phy/amlogic/phy-meson8b-usb2.c
diff --git a/drivers/phy/broadcom/Kconfig b/drivers/phy/broadcom/Kconfig
new file mode 100644
index 000000000000..d2d99023ec50
--- /dev/null
+++ b/drivers/phy/broadcom/Kconfig
@@ -0,0 +1,55 @@
+#
+# Phy drivers for Broadcom platforms
+#
+config PHY_CYGNUS_PCIE
+	tristate "Broadcom Cygnus PCIe PHY driver"
+	depends on OF && (ARCH_BCM_CYGNUS || COMPILE_TEST)
+	select GENERIC_PHY
+	default ARCH_BCM_CYGNUS
+	help
+	  Enable this to support the Broadcom Cygnus PCIe PHY.
+	  If unsure, say N.
+
+config BCM_KONA_USB2_PHY
+	tristate "Broadcom Kona USB2 PHY Driver"
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Enable this to support the Broadcom Kona USB 2.0 PHY.
+
+config PHY_BCM_NS_USB2
+	tristate "Broadcom Northstar USB 2.0 PHY Driver"
+	depends on ARCH_BCM_IPROC || COMPILE_TEST
+	depends on HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support Broadcom USB 2.0 PHY connected to the USB
+	  controller on Northstar family.
+
+config PHY_BCM_NS_USB3
+	tristate "Broadcom Northstar USB 3.0 PHY Driver"
+	depends on ARCH_BCM_IPROC || COMPILE_TEST
+	depends on HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support Broadcom USB 3.0 PHY connected to the USB
+	  controller on Northstar family.
+
+config PHY_NS2_PCIE
+	tristate "Broadcom Northstar2 PCIe PHY driver"
+	depends on OF && MDIO_BUS_MUX_BCM_IPROC
+	select GENERIC_PHY
+	default ARCH_BCM_IPROC
+	help
+	  Enable this to support the Broadcom Northstar2 PCIe PHY.
+	  If unsure, say N.
+
+config PHY_BRCM_SATA
+	tristate "Broadcom SATA PHY driver"
+	depends on ARCH_BRCMSTB || ARCH_BCM_IPROC || BMIPS_GENERIC || COMPILE_TEST
+	depends on OF
+	select GENERIC_PHY
+	default ARCH_BCM_IPROC
+	help
+	  Enable this to support the Broadcom SATA PHY.
+	  If unsure, say N.
diff --git a/drivers/phy/broadcom/Makefile b/drivers/phy/broadcom/Makefile
new file mode 100644
index 000000000000..357a7d16529f
--- /dev/null
+++ b/drivers/phy/broadcom/Makefile
@@ -0,0 +1,6 @@
+obj-$(CONFIG_PHY_CYGNUS_PCIE)		+= phy-bcm-cygnus-pcie.o
+obj-$(CONFIG_BCM_KONA_USB2_PHY)		+= phy-bcm-kona-usb2.o
+obj-$(CONFIG_PHY_BCM_NS_USB2)		+= phy-bcm-ns-usb2.o
+obj-$(CONFIG_PHY_BCM_NS_USB3)		+= phy-bcm-ns-usb3.o
+obj-$(CONFIG_PHY_NS2_PCIE)		+= phy-bcm-ns2-pcie.o
+obj-$(CONFIG_PHY_BRCM_SATA)		+= phy-brcm-sata.o
diff --git a/drivers/phy/phy-bcm-cygnus-pcie.c b/drivers/phy/broadcom/phy-bcm-cygnus-pcie.c
similarity index 100%
rename from drivers/phy/phy-bcm-cygnus-pcie.c
rename to drivers/phy/broadcom/phy-bcm-cygnus-pcie.c
diff --git a/drivers/phy/phy-bcm-kona-usb2.c b/drivers/phy/broadcom/phy-bcm-kona-usb2.c
similarity index 100%
rename from drivers/phy/phy-bcm-kona-usb2.c
rename to drivers/phy/broadcom/phy-bcm-kona-usb2.c
diff --git a/drivers/phy/phy-bcm-ns-usb2.c b/drivers/phy/broadcom/phy-bcm-ns-usb2.c
similarity index 100%
rename from drivers/phy/phy-bcm-ns-usb2.c
rename to drivers/phy/broadcom/phy-bcm-ns-usb2.c
diff --git a/drivers/phy/phy-bcm-ns-usb3.c b/drivers/phy/broadcom/phy-bcm-ns-usb3.c
similarity index 100%
rename from drivers/phy/phy-bcm-ns-usb3.c
rename to drivers/phy/broadcom/phy-bcm-ns-usb3.c
diff --git a/drivers/phy/phy-bcm-ns2-pcie.c b/drivers/phy/broadcom/phy-bcm-ns2-pcie.c
similarity index 100%
rename from drivers/phy/phy-bcm-ns2-pcie.c
rename to drivers/phy/broadcom/phy-bcm-ns2-pcie.c
diff --git a/drivers/phy/phy-brcm-sata.c b/drivers/phy/broadcom/phy-brcm-sata.c
similarity index 100%
rename from drivers/phy/phy-brcm-sata.c
rename to drivers/phy/broadcom/phy-brcm-sata.c
diff --git a/drivers/phy/hisilicon/Kconfig b/drivers/phy/hisilicon/Kconfig
new file mode 100644
index 000000000000..6164c4cd0f65
--- /dev/null
+++ b/drivers/phy/hisilicon/Kconfig
@@ -0,0 +1,20 @@
+#
+# Phy drivers for Hisilicon platforms
+#
+config PHY_HI6220_USB
+	tristate "hi6220 USB PHY support"
+	depends on (ARCH_HISI && ARM64) || COMPILE_TEST
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the HISILICON HI6220 USB PHY.
+
+	  To compile this driver as a module, choose M here.
+
+config PHY_HIX5HD2_SATA
+	tristate "HIX5HD2 SATA PHY Driver"
+	depends on ARCH_HIX5HD2 && OF && HAS_IOMEM
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Support for SATA PHY on Hisilicon hix5hd2 Soc.
diff --git a/drivers/phy/hisilicon/Makefile b/drivers/phy/hisilicon/Makefile
new file mode 100644
index 000000000000..541b348187a8
--- /dev/null
+++ b/drivers/phy/hisilicon/Makefile
@@ -0,0 +1,2 @@
+obj-$(CONFIG_PHY_HI6220_USB)		+= phy-hi6220-usb.o
+obj-$(CONFIG_PHY_HIX5HD2_SATA)		+= phy-hix5hd2-sata.o
diff --git a/drivers/phy/phy-hi6220-usb.c b/drivers/phy/hisilicon/phy-hi6220-usb.c
similarity index 100%
rename from drivers/phy/phy-hi6220-usb.c
rename to drivers/phy/hisilicon/phy-hi6220-usb.c
diff --git a/drivers/phy/phy-hix5hd2-sata.c b/drivers/phy/hisilicon/phy-hix5hd2-sata.c
similarity index 100%
rename from drivers/phy/phy-hix5hd2-sata.c
rename to drivers/phy/hisilicon/phy-hix5hd2-sata.c
diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
new file mode 100644
index 000000000000..048d8893bc2e
--- /dev/null
+++ b/drivers/phy/marvell/Kconfig
@@ -0,0 +1,50 @@
+#
+# Phy drivers for Marvell platforms
+#
+config ARMADA375_USBCLUSTER_PHY
+	def_bool y
+	depends on MACH_ARMADA_375 || COMPILE_TEST
+	depends on OF && HAS_IOMEM
+	select GENERIC_PHY
+
+config PHY_BERLIN_SATA
+	tristate "Marvell Berlin SATA PHY driver"
+	depends on ARCH_BERLIN && HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the SATA PHY on Marvell Berlin SoCs.
+
+config PHY_BERLIN_USB
+	tristate "Marvell Berlin USB PHY Driver"
+	depends on ARCH_BERLIN && RESET_CONTROLLER && HAS_IOMEM && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the USB PHY on Marvell Berlin SoCs.
+
+config PHY_MVEBU_SATA
+	def_bool y
+	depends on ARCH_DOVE || MACH_DOVE || MACH_KIRKWOOD
+	depends on OF
+	select GENERIC_PHY
+
+config PHY_PXA_28NM_HSIC
+	tristate "Marvell USB HSIC 28nm PHY Driver"
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Enable this to support Marvell USB HSIC PHY driver for Marvell
+	  SoC. This driver will do the PHY initialization and shutdown.
+	  The PHY driver will be used by Marvell ehci driver.
+
+	  To compile this driver as a module, choose M here.
+
+config PHY_PXA_28NM_USB2
+	tristate "Marvell USB 2.0 28nm PHY Driver"
+	depends on HAS_IOMEM
+	select GENERIC_PHY
+	help
+	  Enable this to support Marvell USB 2.0 PHY driver for Marvell
+	  SoC. This driver will do the PHY initialization and shutdown.
+	  The PHY driver will be used by Marvell udc/ehci/otg driver.
+
+	  To compile this driver as a module, choose M here.
diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
new file mode 100644
index 000000000000..3fc188f59118
--- /dev/null
+++ b/drivers/phy/marvell/Makefile
@@ -0,0 +1,6 @@
+obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
+obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
+obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
+obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
+obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
+obj-$(CONFIG_PHY_PXA_28NM_USB2)		+= phy-pxa-28nm-usb2.o
diff --git a/drivers/phy/phy-armada375-usb2.c b/drivers/phy/marvell/phy-armada375-usb2.c
similarity index 100%
rename from drivers/phy/phy-armada375-usb2.c
rename to drivers/phy/marvell/phy-armada375-usb2.c
diff --git a/drivers/phy/phy-berlin-sata.c b/drivers/phy/marvell/phy-berlin-sata.c
similarity index 100%
rename from drivers/phy/phy-berlin-sata.c
rename to drivers/phy/marvell/phy-berlin-sata.c
diff --git a/drivers/phy/phy-berlin-usb.c b/drivers/phy/marvell/phy-berlin-usb.c
similarity index 100%
rename from drivers/phy/phy-berlin-usb.c
rename to drivers/phy/marvell/phy-berlin-usb.c
diff --git a/drivers/phy/phy-mvebu-sata.c b/drivers/phy/marvell/phy-mvebu-sata.c
similarity index 100%
rename from drivers/phy/phy-mvebu-sata.c
rename to drivers/phy/marvell/phy-mvebu-sata.c
diff --git a/drivers/phy/phy-pxa-28nm-hsic.c b/drivers/phy/marvell/phy-pxa-28nm-hsic.c
similarity index 100%
rename from drivers/phy/phy-pxa-28nm-hsic.c
rename to drivers/phy/marvell/phy-pxa-28nm-hsic.c
diff --git a/drivers/phy/phy-pxa-28nm-usb2.c b/drivers/phy/marvell/phy-pxa-28nm-usb2.c
similarity index 100%
rename from drivers/phy/phy-pxa-28nm-usb2.c
rename to drivers/phy/marvell/phy-pxa-28nm-usb2.c
diff --git a/drivers/phy/qualcomm/Kconfig b/drivers/phy/qualcomm/Kconfig
new file mode 100644
index 000000000000..7bfa64baf837
--- /dev/null
+++ b/drivers/phy/qualcomm/Kconfig
@@ -0,0 +1,58 @@
+#
+# Phy drivers for Qualcomm platforms
+#
+config PHY_QCOM_APQ8064_SATA
+	tristate "Qualcomm APQ8064 SATA SerDes/PHY driver"
+	depends on ARCH_QCOM
+	depends on HAS_IOMEM
+	depends on OF
+	select GENERIC_PHY
+
+config PHY_QCOM_IPQ806X_SATA
+	tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
+	depends on ARCH_QCOM
+	depends on HAS_IOMEM
+	depends on OF
+	select GENERIC_PHY
+
+config PHY_QCOM_QMP
+	tristate "Qualcomm QMP PHY Driver"
+	depends on OF && COMMON_CLK && (ARCH_QCOM || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable this to support the QMP PHY transceiver that is used
+	  with controllers such as PCIe, UFS, and USB on Qualcomm chips.
+
+config PHY_QCOM_QUSB2
+	tristate "Qualcomm QUSB2 PHY Driver"
+	depends on OF && (ARCH_QCOM || COMPILE_TEST)
+	depends on NVMEM || !NVMEM
+	select GENERIC_PHY
+	help
+	  Enable this to support the HighSpeed QUSB2 PHY transceiver for USB
+	  controllers on Qualcomm chips. This driver supports the high-speed
+	  PHY which is usually paired with either the ChipIdea or Synopsys DWC3
+	  USB IPs on MSM SOCs.
+
+config PHY_QCOM_UFS
+	tristate "Qualcomm UFS PHY driver"
+	depends on OF && ARCH_QCOM
+	select GENERIC_PHY
+	help
+	  Support for UFS PHY on QCOM chipsets.
+
+config PHY_QCOM_USB_HS
+	tristate "Qualcomm USB HS PHY module"
+	depends on USB_ULPI_BUS
+	depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+	select GENERIC_PHY
+	help
+	  Support for the USB high-speed ULPI compliant phy on Qualcomm
+	  chipsets.
+
+config PHY_QCOM_USB_HSIC
+	tristate "Qualcomm USB HSIC ULPI PHY module"
+	depends on USB_ULPI_BUS
+	select GENERIC_PHY
+	help
+	  Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
diff --git a/drivers/phy/qualcomm/Makefile b/drivers/phy/qualcomm/Makefile
new file mode 100644
index 000000000000..2e183d7695fd
--- /dev/null
+++ b/drivers/phy/qualcomm/Makefile
@@ -0,0 +1,9 @@
+obj-$(CONFIG_PHY_QCOM_APQ8064_SATA)	+= phy-qcom-apq8064-sata.o
+obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
+obj-$(CONFIG_PHY_QCOM_QMP)		+= phy-qcom-qmp.o
+obj-$(CONFIG_PHY_QCOM_QUSB2)		+= phy-qcom-qusb2.o
+obj-$(CONFIG_PHY_QCOM_UFS)		+= phy-qcom-ufs.o
+obj-$(CONFIG_PHY_QCOM_UFS)		+= phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_UFS)		+= phy-qcom-ufs-qmp-20nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
+obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
diff --git a/drivers/phy/phy-qcom-apq8064-sata.c b/drivers/phy/qualcomm/phy-qcom-apq8064-sata.c
similarity index 100%
rename from drivers/phy/phy-qcom-apq8064-sata.c
rename to drivers/phy/qualcomm/phy-qcom-apq8064-sata.c
diff --git a/drivers/phy/phy-qcom-ipq806x-sata.c b/drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c
similarity index 100%
rename from drivers/phy/phy-qcom-ipq806x-sata.c
rename to drivers/phy/qualcomm/phy-qcom-ipq806x-sata.c
diff --git a/drivers/phy/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
similarity index 100%
rename from drivers/phy/phy-qcom-qmp.c
rename to drivers/phy/qualcomm/phy-qcom-qmp.c
diff --git a/drivers/phy/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
similarity index 100%
rename from drivers/phy/phy-qcom-qusb2.c
rename to drivers/phy/qualcomm/phy-qcom-qusb2.c
diff --git a/drivers/phy/phy-qcom-ufs-i.h b/drivers/phy/qualcomm/phy-qcom-ufs-i.h
similarity index 100%
rename from drivers/phy/phy-qcom-ufs-i.h
rename to drivers/phy/qualcomm/phy-qcom-ufs-i.h
diff --git a/drivers/phy/phy-qcom-ufs-qmp-14nm.c b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c
similarity index 100%
rename from drivers/phy/phy-qcom-ufs-qmp-14nm.c
rename to drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.c
diff --git a/drivers/phy/phy-qcom-ufs-qmp-14nm.h b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h
similarity index 100%
rename from drivers/phy/phy-qcom-ufs-qmp-14nm.h
rename to drivers/phy/qualcomm/phy-qcom-ufs-qmp-14nm.h
diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.c b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c
similarity index 100%
rename from drivers/phy/phy-qcom-ufs-qmp-20nm.c
rename to drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.c
diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.h b/drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h
similarity index 100%
rename from drivers/phy/phy-qcom-ufs-qmp-20nm.h
rename to drivers/phy/qualcomm/phy-qcom-ufs-qmp-20nm.h
diff --git a/drivers/phy/phy-qcom-ufs.c b/drivers/phy/qualcomm/phy-qcom-ufs.c
similarity index 100%
rename from drivers/phy/phy-qcom-ufs.c
rename to drivers/phy/qualcomm/phy-qcom-ufs.c
diff --git a/drivers/phy/phy-qcom-usb-hs.c b/drivers/phy/qualcomm/phy-qcom-usb-hs.c
similarity index 100%
rename from drivers/phy/phy-qcom-usb-hs.c
rename to drivers/phy/qualcomm/phy-qcom-usb-hs.c
diff --git a/drivers/phy/phy-qcom-usb-hsic.c b/drivers/phy/qualcomm/phy-qcom-usb-hsic.c
similarity index 100%
rename from drivers/phy/phy-qcom-usb-hsic.c
rename to drivers/phy/qualcomm/phy-qcom-usb-hsic.c
diff --git a/drivers/phy/renesas/Kconfig b/drivers/phy/renesas/Kconfig
new file mode 100644
index 000000000000..432e2715e9c4
--- /dev/null
+++ b/drivers/phy/renesas/Kconfig
@@ -0,0 +1,17 @@
+#
+# Phy drivers for Renesas platforms
+#
+config PHY_RCAR_GEN2
+	tristate "Renesas R-Car generation 2 USB PHY driver"
+	depends on ARCH_RENESAS
+	depends on GENERIC_PHY
+	help
+	  Support for USB PHY found on Renesas R-Car generation 2 SoCs.
+
+config PHY_RCAR_GEN3_USB2
+	tristate "Renesas R-Car generation 3 USB 2.0 PHY driver"
+	depends on ARCH_RENESAS
+	depends on EXTCON
+	select GENERIC_PHY
+	help
+	  Support for USB 2.0 PHY found on Renesas R-Car generation 3 SoCs.
diff --git a/drivers/phy/renesas/Makefile b/drivers/phy/renesas/Makefile
new file mode 100644
index 000000000000..695241aebf69
--- /dev/null
+++ b/drivers/phy/renesas/Makefile
@@ -0,0 +1,2 @@
+obj-$(CONFIG_PHY_RCAR_GEN2)		+= phy-rcar-gen2.o
+obj-$(CONFIG_PHY_RCAR_GEN3_USB2)	+= phy-rcar-gen3-usb2.o
diff --git a/drivers/phy/phy-rcar-gen2.c b/drivers/phy/renesas/phy-rcar-gen2.c
similarity index 100%
rename from drivers/phy/phy-rcar-gen2.c
rename to drivers/phy/renesas/phy-rcar-gen2.c
diff --git a/drivers/phy/phy-rcar-gen3-usb2.c b/drivers/phy/renesas/phy-rcar-gen3-usb2.c
similarity index 100%
rename from drivers/phy/phy-rcar-gen3-usb2.c
rename to drivers/phy/renesas/phy-rcar-gen3-usb2.c
diff --git a/drivers/phy/rockchip/Kconfig b/drivers/phy/rockchip/Kconfig
new file mode 100644
index 000000000000..f5325b2b679e
--- /dev/null
+++ b/drivers/phy/rockchip/Kconfig
@@ -0,0 +1,51 @@
+#
+# Phy drivers for Rockchip platforms
+#
+config PHY_ROCKCHIP_DP
+	tristate "Rockchip Display Port PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip Display Port PHY.
+
+config PHY_ROCKCHIP_EMMC
+	tristate "Rockchip EMMC PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip EMMC PHY.
+
+config PHY_ROCKCHIP_INNO_USB2
+	tristate "Rockchip INNO USB2PHY Driver"
+	depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF
+	depends on COMMON_CLK
+	depends on EXTCON
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_COMMON
+	help
+	  Support for Rockchip USB2.0 PHY with Innosilicon IP block.
+
+config PHY_ROCKCHIP_PCIE
+	tristate "Rockchip PCIe PHY Driver"
+	depends on (ARCH_ROCKCHIP && OF) || COMPILE_TEST
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the Rockchip PCIe PHY.
+
+config PHY_ROCKCHIP_TYPEC
+	tristate "Rockchip TYPEC PHY Driver"
+	depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
+	select EXTCON
+	select GENERIC_PHY
+	select RESET_CONTROLLER
+	help
+	  Enable this to support the Rockchip USB TYPEC PHY.
+
+config PHY_ROCKCHIP_USB
+	tristate "Rockchip USB2 PHY Driver"
+	depends on ARCH_ROCKCHIP && OF
+	select GENERIC_PHY
+	help
+	  Enable this to support the Rockchip USB 2.0 PHY.
diff --git a/drivers/phy/rockchip/Makefile b/drivers/phy/rockchip/Makefile
new file mode 100644
index 000000000000..bd0acdf38e0f
--- /dev/null
+++ b/drivers/phy/rockchip/Makefile
@@ -0,0 +1,6 @@
+obj-$(CONFIG_PHY_ROCKCHIP_DP)		+= phy-rockchip-dp.o
+obj-$(CONFIG_PHY_ROCKCHIP_EMMC)		+= phy-rockchip-emmc.o
+obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2)	+= phy-rockchip-inno-usb2.o
+obj-$(CONFIG_PHY_ROCKCHIP_PCIE)		+= phy-rockchip-pcie.o
+obj-$(CONFIG_PHY_ROCKCHIP_TYPEC)	+= phy-rockchip-typec.o
+obj-$(CONFIG_PHY_ROCKCHIP_USB)		+= phy-rockchip-usb.o
diff --git a/drivers/phy/phy-rockchip-dp.c b/drivers/phy/rockchip/phy-rockchip-dp.c
similarity index 100%
rename from drivers/phy/phy-rockchip-dp.c
rename to drivers/phy/rockchip/phy-rockchip-dp.c
diff --git a/drivers/phy/phy-rockchip-emmc.c b/drivers/phy/rockchip/phy-rockchip-emmc.c
similarity index 100%
rename from drivers/phy/phy-rockchip-emmc.c
rename to drivers/phy/rockchip/phy-rockchip-emmc.c
diff --git a/drivers/phy/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
similarity index 100%
rename from drivers/phy/phy-rockchip-inno-usb2.c
rename to drivers/phy/rockchip/phy-rockchip-inno-usb2.c
diff --git a/drivers/phy/phy-rockchip-pcie.c b/drivers/phy/rockchip/phy-rockchip-pcie.c
similarity index 100%
rename from drivers/phy/phy-rockchip-pcie.c
rename to drivers/phy/rockchip/phy-rockchip-pcie.c
diff --git a/drivers/phy/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c
similarity index 100%
rename from drivers/phy/phy-rockchip-typec.c
rename to drivers/phy/rockchip/phy-rockchip-typec.c
diff --git a/drivers/phy/phy-rockchip-usb.c b/drivers/phy/rockchip/phy-rockchip-usb.c
similarity index 100%
rename from drivers/phy/phy-rockchip-usb.c
rename to drivers/phy/rockchip/phy-rockchip-usb.c
diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig
new file mode 100644
index 000000000000..b7e0645a7bd9
--- /dev/null
+++ b/drivers/phy/samsung/Kconfig
@@ -0,0 +1,95 @@
+#
+# Phy drivers for Samsung platforms
+#
+config PHY_EXYNOS_DP_VIDEO
+	tristate "EXYNOS SoC series Display Port PHY driver"
+	depends on OF
+	depends on ARCH_EXYNOS || COMPILE_TEST
+	default ARCH_EXYNOS
+	select GENERIC_PHY
+	help
+	  Support for Display Port PHY found on Samsung EXYNOS SoCs.
+
+config PHY_EXYNOS_MIPI_VIDEO
+	tristate "S5P/EXYNOS SoC series MIPI CSI-2/DSI PHY driver"
+	depends on HAS_IOMEM
+	depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
+	select GENERIC_PHY
+	default y if ARCH_S5PV210 || ARCH_EXYNOS
+	help
+	  Support for MIPI CSI-2 and MIPI DSI DPHY found on Samsung S5P
+	  and EXYNOS SoCs.
+
+config PHY_EXYNOS_PCIE
+	bool "Exynos PCIe PHY driver"
+	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable PCIe PHY support for Exynos SoC series.
+	  This driver provides PHY interface for Exynos PCIe controller.
+
+config PHY_SAMSUNG_USB2
+	tristate "Samsung USB 2.0 PHY driver"
+	depends on HAS_IOMEM
+	depends on USB_EHCI_EXYNOS || USB_OHCI_EXYNOS || USB_DWC2
+	select GENERIC_PHY
+	select MFD_SYSCON
+	default ARCH_EXYNOS
+	help
+	  Enable this to support the Samsung USB 2.0 PHY driver for Samsung
+	  SoCs. This driver provides the interface for USB 2.0 PHY. Support
+	  for particular PHYs will be enabled based on the SoC type in addition
+	  to this driver.
+
+config PHY_EXYNOS4210_USB2
+	bool
+	depends on PHY_SAMSUNG_USB2
+	default CPU_EXYNOS4210
+
+config PHY_EXYNOS4X12_USB2
+	bool
+	depends on PHY_SAMSUNG_USB2
+	default SOC_EXYNOS3250 || SOC_EXYNOS4212 || SOC_EXYNOS4412
+
+config PHY_EXYNOS5250_USB2
+	bool
+	depends on PHY_SAMSUNG_USB2
+	default SOC_EXYNOS5250 || SOC_EXYNOS5420
+
+config PHY_S5PV210_USB2
+	bool "Support for S5PV210"
+	depends on PHY_SAMSUNG_USB2
+	depends on ARCH_S5PV210
+	help
+	  Enable USB PHY support for S5PV210. This option requires that Samsung
+	  USB 2.0 PHY driver is enabled and means that support for this
+	  particular SoC is compiled in the driver. In case of S5PV210 two phys
+	  are available - device and host.
+
+config PHY_EXYNOS5_USBDRD
+	tristate "Exynos5 SoC series USB DRD PHY driver"
+	depends on ARCH_EXYNOS && OF
+	depends on HAS_IOMEM
+	depends on USB_DWC3_EXYNOS
+	select GENERIC_PHY
+	select MFD_SYSCON
+	default y
+	help
+	  Enable USB DRD PHY support for Exynos 5 SoC series.
+	  This driver provides PHY interface for USB 3.0 DRD controller
+	  present on Exynos5 SoC series.
+
+config PHY_EXYNOS5250_SATA
+	tristate "Exynos5250 Sata SerDes/PHY driver"
+	depends on SOC_EXYNOS5250
+	depends on HAS_IOMEM
+	depends on OF
+	select GENERIC_PHY
+	select I2C
+	select I2C_S3C2410
+	select MFD_SYSCON
+	help
+	  Enable this to support SATA SerDes/Phy found on Samsung's
+	  Exynos5250 based SoCs.This SerDes/Phy supports SATA 1.5 Gb/s,
+	  SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds. It supports one SATA host
+	  port to accept one SATA device.
diff --git a/drivers/phy/samsung/Makefile b/drivers/phy/samsung/Makefile
new file mode 100644
index 000000000000..20d7f2424772
--- /dev/null
+++ b/drivers/phy/samsung/Makefile
@@ -0,0 +1,11 @@
+obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
+obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
+obj-$(CONFIG_PHY_EXYNOS_PCIE)		+= phy-exynos-pcie.o
+obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
+phy-exynos-usb2-y			+= phy-samsung-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
+obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
+obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
diff --git a/drivers/phy/phy-exynos-dp-video.c b/drivers/phy/samsung/phy-exynos-dp-video.c
similarity index 100%
rename from drivers/phy/phy-exynos-dp-video.c
rename to drivers/phy/samsung/phy-exynos-dp-video.c
diff --git a/drivers/phy/phy-exynos-mipi-video.c b/drivers/phy/samsung/phy-exynos-mipi-video.c
similarity index 100%
rename from drivers/phy/phy-exynos-mipi-video.c
rename to drivers/phy/samsung/phy-exynos-mipi-video.c
diff --git a/drivers/phy/phy-exynos-pcie.c b/drivers/phy/samsung/phy-exynos-pcie.c
similarity index 100%
rename from drivers/phy/phy-exynos-pcie.c
rename to drivers/phy/samsung/phy-exynos-pcie.c
diff --git a/drivers/phy/phy-exynos4210-usb2.c b/drivers/phy/samsung/phy-exynos4210-usb2.c
similarity index 100%
rename from drivers/phy/phy-exynos4210-usb2.c
rename to drivers/phy/samsung/phy-exynos4210-usb2.c
diff --git a/drivers/phy/phy-exynos4x12-usb2.c b/drivers/phy/samsung/phy-exynos4x12-usb2.c
similarity index 100%
rename from drivers/phy/phy-exynos4x12-usb2.c
rename to drivers/phy/samsung/phy-exynos4x12-usb2.c
diff --git a/drivers/phy/phy-exynos5-usbdrd.c b/drivers/phy/samsung/phy-exynos5-usbdrd.c
similarity index 100%
rename from drivers/phy/phy-exynos5-usbdrd.c
rename to drivers/phy/samsung/phy-exynos5-usbdrd.c
diff --git a/drivers/phy/phy-exynos5250-sata.c b/drivers/phy/samsung/phy-exynos5250-sata.c
similarity index 100%
rename from drivers/phy/phy-exynos5250-sata.c
rename to drivers/phy/samsung/phy-exynos5250-sata.c
diff --git a/drivers/phy/phy-exynos5250-usb2.c b/drivers/phy/samsung/phy-exynos5250-usb2.c
similarity index 100%
rename from drivers/phy/phy-exynos5250-usb2.c
rename to drivers/phy/samsung/phy-exynos5250-usb2.c
diff --git a/drivers/phy/phy-s5pv210-usb2.c b/drivers/phy/samsung/phy-s5pv210-usb2.c
similarity index 100%
rename from drivers/phy/phy-s5pv210-usb2.c
rename to drivers/phy/samsung/phy-s5pv210-usb2.c
diff --git a/drivers/phy/phy-samsung-usb2.c b/drivers/phy/samsung/phy-samsung-usb2.c
similarity index 100%
rename from drivers/phy/phy-samsung-usb2.c
rename to drivers/phy/samsung/phy-samsung-usb2.c
diff --git a/drivers/phy/phy-samsung-usb2.h b/drivers/phy/samsung/phy-samsung-usb2.h
similarity index 100%
rename from drivers/phy/phy-samsung-usb2.h
rename to drivers/phy/samsung/phy-samsung-usb2.h
diff --git a/drivers/phy/st/Kconfig b/drivers/phy/st/Kconfig
new file mode 100644
index 000000000000..0814d3f87ec6
--- /dev/null
+++ b/drivers/phy/st/Kconfig
@@ -0,0 +1,33 @@
+#
+# Phy drivers for STMicro platforms
+#
+config PHY_MIPHY28LP
+	tristate "STMicroelectronics MIPHY28LP PHY driver for STiH407"
+	depends on ARCH_STI
+	select GENERIC_PHY
+	help
+	  Enable this to support the miphy transceiver (for SATA/PCIE/USB3)
+	  that is part of STMicroelectronics STiH407 SoC.
+
+config PHY_ST_SPEAR1310_MIPHY
+	tristate "ST SPEAR1310-MIPHY driver"
+	select GENERIC_PHY
+	depends on MACH_SPEAR1310 || COMPILE_TEST
+	help
+	  Support for ST SPEAr1310 MIPHY which can be used for PCIe and SATA.
+
+config PHY_ST_SPEAR1340_MIPHY
+	tristate "ST SPEAR1340-MIPHY driver"
+	select GENERIC_PHY
+	depends on MACH_SPEAR1340 || COMPILE_TEST
+	help
+	  Support for ST SPEAr1340 MIPHY which can be used for PCIe and SATA.
+
+config PHY_STIH407_USB
+	tristate "STMicroelectronics USB2 picoPHY driver for STiH407 family"
+	depends on RESET_CONTROLLER
+	depends on ARCH_STI || COMPILE_TEST
+	select GENERIC_PHY
+	help
+	  Enable this support to enable the picoPHY device used by USB2
+	  and USB3 controllers on STMicroelectronics STiH407 SoC families.
diff --git a/drivers/phy/st/Makefile b/drivers/phy/st/Makefile
new file mode 100644
index 000000000000..e2adfe2166d2
--- /dev/null
+++ b/drivers/phy/st/Makefile
@@ -0,0 +1,4 @@
+obj-$(CONFIG_PHY_MIPHY28LP) 		+= phy-miphy28lp.o
+obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY)	+= phy-spear1310-miphy.o
+obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY)	+= phy-spear1340-miphy.o
+obj-$(CONFIG_PHY_STIH407_USB)		+= phy-stih407-usb.o
diff --git a/drivers/phy/phy-miphy28lp.c b/drivers/phy/st/phy-miphy28lp.c
similarity index 100%
rename from drivers/phy/phy-miphy28lp.c
rename to drivers/phy/st/phy-miphy28lp.c
diff --git a/drivers/phy/phy-spear1310-miphy.c b/drivers/phy/st/phy-spear1310-miphy.c
similarity index 100%
rename from drivers/phy/phy-spear1310-miphy.c
rename to drivers/phy/st/phy-spear1310-miphy.c
diff --git a/drivers/phy/phy-spear1340-miphy.c b/drivers/phy/st/phy-spear1340-miphy.c
similarity index 100%
rename from drivers/phy/phy-spear1340-miphy.c
rename to drivers/phy/st/phy-spear1340-miphy.c
diff --git a/drivers/phy/phy-stih407-usb.c b/drivers/phy/st/phy-stih407-usb.c
similarity index 100%
rename from drivers/phy/phy-stih407-usb.c
rename to drivers/phy/st/phy-stih407-usb.c
diff --git a/drivers/phy/ti/Kconfig b/drivers/phy/ti/Kconfig
new file mode 100644
index 000000000000..20503562666c
--- /dev/null
+++ b/drivers/phy/ti/Kconfig
@@ -0,0 +1,78 @@
+#
+# Phy drivers for TI platforms
+#
+config PHY_DA8XX_USB
+	tristate "TI DA8xx USB PHY Driver"
+	depends on ARCH_DAVINCI_DA8XX
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  Enable this to support the USB PHY on DA8xx SoCs.
+
+	  This driver controls both the USB 1.1 PHY and the USB 2.0 PHY.
+
+config PHY_DM816X_USB
+	tristate "TI dm816x USB PHY driver"
+	depends on ARCH_OMAP2PLUS
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_PHY
+	help
+	  Enable this for dm816x USB to work.
+
+config OMAP_CONTROL_PHY
+	tristate "OMAP CONTROL PHY Driver"
+	depends on ARCH_OMAP2PLUS || COMPILE_TEST
+	help
+	  Enable this to add support for the PHY part present in the control
+	  module. This driver has API to power on the USB2 PHY and to write to
+	  the mailbox. The mailbox is present only in omap4 and the register to
+	  power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an
+	  additional register to power on USB3 PHY/SATA PHY/PCIE PHY
+	  (PIPE3 PHY).
+
+config OMAP_USB2
+	tristate "OMAP USB2 PHY Driver"
+	depends on ARCH_OMAP2PLUS
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_PHY
+	select OMAP_CONTROL_PHY
+	depends on OMAP_OCP2SCP
+	help
+	  Enable this to support the transceiver that is part of SOC. This
+	  driver takes care of all the PHY functionality apart from comparator.
+	  The USB OTG controller communicates with the comparator using this
+	  driver.
+
+config TI_PIPE3
+	tristate "TI PIPE3 PHY Driver"
+	depends on ARCH_OMAP2PLUS || COMPILE_TEST
+	select GENERIC_PHY
+	select OMAP_CONTROL_PHY
+	depends on OMAP_OCP2SCP
+	help
+	  Enable this to support the PIPE3 PHY that is part of TI SOCs. This
+	  driver takes care of all the PHY functionality apart from comparator.
+	  This driver interacts with the "OMAP Control PHY Driver" to power
+	  on/off the PHY.
+
+config PHY_TUSB1210
+	tristate "TI TUSB1210 ULPI PHY module"
+	depends on USB_ULPI_BUS
+	select GENERIC_PHY
+	help
+	  Support for TI TUSB1210 USB ULPI PHY.
+
+config TWL4030_USB
+	tristate "TWL4030 USB Transceiver Driver"
+	depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS
+	depends on USB_SUPPORT
+	depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y'
+	select GENERIC_PHY
+	select USB_PHY
+	help
+	  Enable this to support the USB OTG transceiver on TWL4030
+	  family chips (including the TWL5030 and TPS659x0 devices).
+	  This transceiver supports high and full speed devices plus,
+	  in host mode, low speed.
diff --git a/drivers/phy/ti/Makefile b/drivers/phy/ti/Makefile
new file mode 100644
index 000000000000..0cc3a1a557a3
--- /dev/null
+++ b/drivers/phy/ti/Makefile
@@ -0,0 +1,7 @@
+obj-$(CONFIG_PHY_DA8XX_USB)		+= phy-da8xx-usb.o
+obj-$(CONFIG_PHY_DM816X_USB)		+= phy-dm816x-usb.o
+obj-$(CONFIG_OMAP_CONTROL_PHY)		+= phy-omap-control.o
+obj-$(CONFIG_OMAP_USB2)			+= phy-omap-usb2.o
+obj-$(CONFIG_TI_PIPE3)			+= phy-ti-pipe3.o
+obj-$(CONFIG_PHY_TUSB1210)		+= phy-tusb1210.o
+obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
diff --git a/drivers/phy/phy-da8xx-usb.c b/drivers/phy/ti/phy-da8xx-usb.c
similarity index 100%
rename from drivers/phy/phy-da8xx-usb.c
rename to drivers/phy/ti/phy-da8xx-usb.c
diff --git a/drivers/phy/phy-dm816x-usb.c b/drivers/phy/ti/phy-dm816x-usb.c
similarity index 100%
rename from drivers/phy/phy-dm816x-usb.c
rename to drivers/phy/ti/phy-dm816x-usb.c
diff --git a/drivers/phy/phy-omap-control.c b/drivers/phy/ti/phy-omap-control.c
similarity index 100%
rename from drivers/phy/phy-omap-control.c
rename to drivers/phy/ti/phy-omap-control.c
diff --git a/drivers/phy/phy-omap-usb2.c b/drivers/phy/ti/phy-omap-usb2.c
similarity index 100%
rename from drivers/phy/phy-omap-usb2.c
rename to drivers/phy/ti/phy-omap-usb2.c
diff --git a/drivers/phy/phy-ti-pipe3.c b/drivers/phy/ti/phy-ti-pipe3.c
similarity index 100%
rename from drivers/phy/phy-ti-pipe3.c
rename to drivers/phy/ti/phy-ti-pipe3.c
diff --git a/drivers/phy/phy-tusb1210.c b/drivers/phy/ti/phy-tusb1210.c
similarity index 100%
rename from drivers/phy/phy-tusb1210.c
rename to drivers/phy/ti/phy-tusb1210.c
diff --git a/drivers/phy/phy-twl4030-usb.c b/drivers/phy/ti/phy-twl4030-usb.c
similarity index 100%
rename from drivers/phy/phy-twl4030-usb.c
rename to drivers/phy/ti/phy-twl4030-usb.c
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH v5 3/3] phy: Group vendor specific phy drivers

[Kishon Vijay Abraham I]

Hi Vivek,

On Thursday 11 May 2017 12:17 PM, Vivek Gautam wrote:
> Adding vendor specific directories in phy to group
> phy drivers under their respective vendor umbrella.
> 
> Also updated the MAINTAINERS file to reflect the correct
> directory structure for phy drivers.
> 
> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
> Acked-by: Heiko Stuebner <heiko@sntech.de>
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
> Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
> Cc: Kishon Vijay Abraham I <kishon@ti.com>
> Cc: David S. Miller <davem@davemloft.net>
> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> Cc: Guenter Roeck <linux@roeck-us.net>
> Cc: Heiko Stuebner <heiko@sntech.de>
> Cc: Viresh Kumar <viresh.kumar@linaro.org>
> Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
> Cc: Chen-Yu Tsai <wens@csie.org>
> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
> Cc: Krzysztof Kozlowski <krzk@kernel.org>
> Cc: Jaehoon Chung <jh80.chung@samsung.com>
> Cc: Stephen Boyd <stephen.boyd@linaro.org>
> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: linux-arm-msm@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-omap@vger.kernel.org
> Cc: linux-renesas-soc@vger.kernel.org
> Cc: linux-rockchip@lists.infradead.org
> Cc: linux-samsung-soc@vger.kernel.org
> Cc: linux-usb@vger.kernel.org
> ---
> 
> Changes since v4:
>  - Reprepared the patch based on latest torvalds/master.
>  - Added new directory for amlogic, since there's a new patch [1]
>    coming in for amlogic platforms.

I don't prefer placeholder directories but this is not a placeholder directory
since phy-meson8b-usb2.c is already added in amlogic.

Btw, thank you for sending this patch. Will queue this once -rc1 is tagged.

Cheers
Kishon

Re: [PATCH v5 3/3] phy: Group vendor specific phy drivers

[Vivek Gautam]

On 05/12/2017 02:15 PM, Kishon Vijay Abraham I wrote:
> Hi Vivek,
>
> On Thursday 11 May 2017 12:17 PM, Vivek Gautam wrote:
>> Adding vendor specific directories in phy to group
>> phy drivers under their respective vendor umbrella.
>>
>> Also updated the MAINTAINERS file to reflect the correct
>> directory structure for phy drivers.
>>
>> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
>> Acked-by: Heiko Stuebner <heiko@sntech.de>
>> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
>> Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
>> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
>> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
>> Cc: Kishon Vijay Abraham I <kishon@ti.com>
>> Cc: David S. Miller <davem@davemloft.net>
>> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
>> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
>> Cc: Guenter Roeck <linux@roeck-us.net>
>> Cc: Heiko Stuebner <heiko@sntech.de>
>> Cc: Viresh Kumar <viresh.kumar@linaro.org>
>> Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
>> Cc: Chen-Yu Tsai <wens@csie.org>
>> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Cc: Krzysztof Kozlowski <krzk@kernel.org>
>> Cc: Jaehoon Chung <jh80.chung@samsung.com>
>> Cc: Stephen Boyd <stephen.boyd@linaro.org>
>> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>> Cc: linux-arm-kernel@lists.infradead.org
>> Cc: linux-arm-msm@vger.kernel.org
>> Cc: linux-kernel@vger.kernel.org
>> Cc: linux-omap@vger.kernel.org
>> Cc: linux-renesas-soc@vger.kernel.org
>> Cc: linux-rockchip@lists.infradead.org
>> Cc: linux-samsung-soc@vger.kernel.org
>> Cc: linux-usb@vger.kernel.org
>> ---
>>
>> Changes since v4:
>>   - Reprepared the patch based on latest torvalds/master.
>>   - Added new directory for amlogic, since there's a new patch [1]
>>     coming in for amlogic platforms.
> I don't prefer placeholder directories but this is not a placeholder directory
> since phy-meson8b-usb2.c is already added in amlogic.

Right, since phy-meson8b-usb2.c was already there and phy-meson-gxl-usb2.c
is also coming, i decided to add this directory.
> Btw, thank you for sending this patch. Will queue this once -rc1 is tagged.

Cool. Thanks Kishon.

Regards
Vivek

>
> Cheers
> Kishon
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

-- 
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v5 3/3] phy: Group vendor specific phy drivers

[Kishon Vijay Abraham I]

Hi Vivek,

On Thursday 11 May 2017 12:17 PM, Vivek Gautam wrote:
> Adding vendor specific directories in phy to group
> phy drivers under their respective vendor umbrella.
> 
> Also updated the MAINTAINERS file to reflect the correct
> directory structure for phy drivers.
> 
> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
> Acked-by: Heiko Stuebner <heiko@sntech.de>
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
> Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
> Cc: Kishon Vijay Abraham I <kishon@ti.com>
> Cc: David S. Miller <davem@davemloft.net>
> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> Cc: Guenter Roeck <linux@roeck-us.net>
> Cc: Heiko Stuebner <heiko@sntech.de>
> Cc: Viresh Kumar <viresh.kumar@linaro.org>
> Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
> Cc: Chen-Yu Tsai <wens@csie.org>
> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
> Cc: Krzysztof Kozlowski <krzk@kernel.org>
> Cc: Jaehoon Chung <jh80.chung@samsung.com>
> Cc: Stephen Boyd <stephen.boyd@linaro.org>
> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: linux-arm-msm@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-omap@vger.kernel.org
> Cc: linux-renesas-soc@vger.kernel.org
> Cc: linux-rockchip@lists.infradead.org
> Cc: linux-samsung-soc@vger.kernel.org
> Cc: linux-usb@vger.kernel.org
> ---
> 
> Changes since v4:
>  - Reprepared the patch based on latest torvalds/master.
>  - Added new directory for amlogic, since there's a new patch [1]
>    coming in for amlogic platforms.
> 
> Changes since v3:
>  - Added 'Acked-by' and 'Reviewed by' tags received for this patch.
>  - No functional change.
> 
> Changes since v2:
>  - Rebased on linux-phy/next.
>  - Took care of drivers added/removed for each vendors since v2.
>  - Updated the 'Signed-off-by' tag with my current email id.
> 
> Changes from v1:
>  - Updated the MAINTAINERS file to reflect the same change
>    in directory structure.
>  - Removed PHY_PLAT config as pointed out by Kishon.
>    So we don't require the second patch in the v1 of this series:
>    [PATCH 2/2] arm: mach-spear: Enable PHY_PLAT to meet dependency
>  - Renamed sunxi --> allwinner; rcar --> renesas.
>  - Fixed error coming with qcom Makefile.
> 
> * Build tested multi_v7_defconfig.
> * Build tested arm64 defconfig with all the involved configs enabled.
> 
> [1] https://patchwork.kernel.org/patch/9684303/
>
.
.
<snip>
.
.
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index afaf7b643eeb..b353ac603ea0 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -15,73 +15,6 @@ config GENERIC_PHY
>  	  phy users can obtain reference to the PHY. All the users of this

.
.
<snip>
.
.
> -
> +menu "Platform Phy drivers"

I don't think creating a new menu is required. I removed it and merged into
linux-phy.

Thanks
Kishon

Re: [PATCH v5 3/3] phy: Group vendor specific phy drivers

[Vivek Gautam]

On 05/16/2017 03:40 PM, Kishon Vijay Abraham I wrote:
> Hi Vivek,
>
> On Thursday 11 May 2017 12:17 PM, Vivek Gautam wrote:
>> Adding vendor specific directories in phy to group
>> phy drivers under their respective vendor umbrella.
>>
>> Also updated the MAINTAINERS file to reflect the correct
>> directory structure for phy drivers.
>>
>> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
>> Acked-by: Heiko Stuebner <heiko@sntech.de>
>> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
>> Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
>> Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
>> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
>> Cc: Kishon Vijay Abraham I <kishon@ti.com>
>> Cc: David S. Miller <davem@davemloft.net>
>> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
>> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
>> Cc: Guenter Roeck <linux@roeck-us.net>
>> Cc: Heiko Stuebner <heiko@sntech.de>
>> Cc: Viresh Kumar <viresh.kumar@linaro.org>
>> Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
>> Cc: Chen-Yu Tsai <wens@csie.org>
>> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
>> Cc: Krzysztof Kozlowski <krzk@kernel.org>
>> Cc: Jaehoon Chung <jh80.chung@samsung.com>
>> Cc: Stephen Boyd <stephen.boyd@linaro.org>
>> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>> Cc: linux-arm-kernel@lists.infradead.org
>> Cc: linux-arm-msm@vger.kernel.org
>> Cc: linux-kernel@vger.kernel.org
>> Cc: linux-omap@vger.kernel.org
>> Cc: linux-renesas-soc@vger.kernel.org
>> Cc: linux-rockchip@lists.infradead.org
>> Cc: linux-samsung-soc@vger.kernel.org
>> Cc: linux-usb@vger.kernel.org
>> ---
>>
>> Changes since v4:
>>   - Reprepared the patch based on latest torvalds/master.
>>   - Added new directory for amlogic, since there's a new patch [1]
>>     coming in for amlogic platforms.
>>
>> Changes since v3:
>>   - Added 'Acked-by' and 'Reviewed by' tags received for this patch.
>>   - No functional change.
>>
>> Changes since v2:
>>   - Rebased on linux-phy/next.
>>   - Took care of drivers added/removed for each vendors since v2.
>>   - Updated the 'Signed-off-by' tag with my current email id.
>>
>> Changes from v1:
>>   - Updated the MAINTAINERS file to reflect the same change
>>     in directory structure.
>>   - Removed PHY_PLAT config as pointed out by Kishon.
>>     So we don't require the second patch in the v1 of this series:
>>     [PATCH 2/2] arm: mach-spear: Enable PHY_PLAT to meet dependency
>>   - Renamed sunxi --> allwinner; rcar --> renesas.
>>   - Fixed error coming with qcom Makefile.
>>
>> * Build tested multi_v7_defconfig.
>> * Build tested arm64 defconfig with all the involved configs enabled.
>>
>> [1] https://patchwork.kernel.org/patch/9684303/
>>
> .
> .
> <snip>
> .
> .
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index afaf7b643eeb..b353ac603ea0 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -15,73 +15,6 @@ config GENERIC_PHY
>>   	  phy users can obtain reference to the PHY. All the users of this
> .
> .
> <snip>
> .
> .
>> -
>> +menu "Platform Phy drivers"
> I don't think creating a new menu is required. I removed it and merged into
> linux-phy.

Right. No need for a new menu. Thank you for fixing it and pushing out.

Best Regards
Vivek

>
> Thanks
> Kishon
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

-- 
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project