* [PATCH 0/2] ARM: dts: am5729: beaglebone-ai: Enable BeagleBone AI @ 2019-11-14 17:06 Caleb Robey 2019-11-14 17:06 ` [PATCH 1/2] ARM: dts: am5729: beaglebone-ai: dra7 reqs in dts Caleb Robey 2019-11-14 17:06 ` [PATCH 2/2] ARM: dts: am5729: beaglebone-ai: adding device tree Caleb Robey 0 siblings, 2 replies; 5+ messages in thread From: Caleb Robey @ 2019-11-14 17:06 UTC (permalink / raw) To: linux_omap Cc: Jason Kridner, Lokesh Vutla, Jason Kridner, Faiz Abbas, Andreas Dannenberg, Jean-Jacques Hiblot, Caleb Robey, Praneeth Bajjuri, Andrew F . Davis, Grygorii Strashko, Tom Rini, Rob Herring, Mark Rutland, Benoît Cousson, Tony Lindgren, devicetree, linux-kernel, linux-omap The following patches 1) Minor change to dra7.dtsi 2) Add device tree file for BeagleBone AI update: moved dra7.dtsi changes before dts addition to prevent compilation breaks Caleb Robey (2): ARM: dts: am5729: beaglebone-ai: dra7 reqs in dts ARM: dts: am5729: beaglebone-ai: adding device tree arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am5729-beagleboneai.dts | 733 ++++++++++++++++++++++ arch/arm/boot/dts/dra7.dtsi | 2 +- 3 files changed, 735 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts -- 2.17.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/2] ARM: dts: am5729: beaglebone-ai: dra7 reqs in dts 2019-11-14 17:06 [PATCH 0/2] ARM: dts: am5729: beaglebone-ai: Enable BeagleBone AI Caleb Robey @ 2019-11-14 17:06 ` Caleb Robey 2019-11-14 17:06 ` [PATCH 2/2] ARM: dts: am5729: beaglebone-ai: adding device tree Caleb Robey 1 sibling, 0 replies; 5+ messages in thread From: Caleb Robey @ 2019-11-14 17:06 UTC (permalink / raw) To: linux_omap Cc: Jason Kridner, Lokesh Vutla, Jason Kridner, Faiz Abbas, Andreas Dannenberg, Jean-Jacques Hiblot, Caleb Robey, Praneeth Bajjuri, Andrew F . Davis, Grygorii Strashko, Tom Rini, Rob Herring, Mark Rutland, Benoît Cousson, Tony Lindgren, devicetree, linux-kernel, linux-omap Small nomenclature change for beaglebone AI compatibility. Signed-off-by: Jason Kridner <jdk@ti.com> Signed-off-by: Caleb Robey <c-robey@ti.com> --- arch/arm/boot/dts/dra7.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 953f0ffce2a9..563d64c69fd4 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -143,7 +143,7 @@ * the moment, just use a fake OCP bus entry to represent the whole bus * hierarchy. */ - ocp { + ocp: ocp { compatible = "ti,dra7-l3-noc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; -- 2.17.1 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/2] ARM: dts: am5729: beaglebone-ai: adding device tree 2019-11-14 17:06 [PATCH 0/2] ARM: dts: am5729: beaglebone-ai: Enable BeagleBone AI Caleb Robey 2019-11-14 17:06 ` [PATCH 1/2] ARM: dts: am5729: beaglebone-ai: dra7 reqs in dts Caleb Robey @ 2019-11-14 17:06 ` Caleb Robey 1 sibling, 0 replies; 5+ messages in thread From: Caleb Robey @ 2019-11-14 17:06 UTC (permalink / raw) To: linux_omap Cc: Jason Kridner, Lokesh Vutla, Jason Kridner, Faiz Abbas, Andreas Dannenberg, Jean-Jacques Hiblot, Caleb Robey, Praneeth Bajjuri, Andrew F . Davis, Grygorii Strashko, Tom Rini, Robert Nelson, Rob Herring, Mark Rutland, Benoît Cousson, Tony Lindgren, devicetree, linux-kernel, linux-omap From: Jason Kridner <jdk@ti.com> BeagleBoard.org BeagleBone AI is an open source hardware single board computer based on the Texas Instruments AM5729 SoC featuring dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4 processors, dual programmable realtime unit industrial control subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion headers. For more information, refer to: https://beaglebone.ai This patch introduces the BeagleBone AI device tree. Note that the device use the "ti,tpd12s016" component which is software compatible with "ti,tpd12s015". Thus we only use the latter driver. Signed-off-by: Jason Kridner <jdk@ti.com> Cc: Robert Nelson <robertcnelson@gmail.com> Cc: Caleb Robey <c-robey@ti.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am5729-beagleboneai.dts | 733 ++++++++++++++++++++++ 2 files changed, 734 insertions(+) create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b21b3a64641a..b1154dbda73c 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -791,6 +791,7 @@ dtb-$(CONFIG_SOC_DRA7XX) += \ am57xx-beagle-x15.dtb \ am57xx-beagle-x15-revb1.dtb \ am57xx-beagle-x15-revc.dtb \ + am5729-beagleboneai.dtb \ am57xx-cl-som-am57x.dtb \ am57xx-sbc-am57x.dtb \ am572x-idk.dtb \ diff --git a/arch/arm/boot/dts/am5729-beagleboneai.dts b/arch/arm/boot/dts/am5729-beagleboneai.dts new file mode 100644 index 000000000000..76551295290a --- /dev/null +++ b/arch/arm/boot/dts/am5729-beagleboneai.dts @@ -0,0 +1,733 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2014-2019 Texas Instruments Incorporated - http://www.ti.com/ + */ + +/dts-v1/; + +#include "dra74x.dtsi" +#include "am57xx-commercial-grade.dtsi" +#include "dra74x-mmc-iodelay.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/dra.h> + +/ { + model = "BeagleBoard.org BeagleBone AI"; + compatible = "beagleboard.org,am5729-beagleboneai", "ti,am5728", + "ti,dra742", "ti,dra74", "ti,dra7"; + + aliases { + rtc0 = &tps659038_rtc; + rtc1 = &rtc; + display0 = &hdmi_conn; + }; + + chosen { + stdout-path = &uart1; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x80000000 0x0 0x40000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ipu2_memory_region: ipu2-memory@95800000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x95800000 0x0 0x3800000>; + reusable; + status = "okay"; + }; + + dsp1_memory_region: dsp1-memory@99000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x99000000 0x0 0x4000000>; + reusable; + status = "okay"; + }; + + ipu1_memory_region: ipu1-memory@9d000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x9d000000 0x0 0x2000000>; + reusable; + status = "okay"; + }; + + dsp2_memory_region: dsp2-memory@9f000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x9f000000 0x0 0x800000>; + reusable; + status = "okay"; + }; + + }; + + vdd_adc: gpioregulator-vdd_adc { + compatible = "regulator-gpio"; + regulator-name = "vdd_adc"; + vin-supply = <&vdd_5v>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; + states = <1800000 0 + 3300000 1>; + }; + + vdd_5v: fixedregulator-vdd_5v { + compatible = "regulator-fixed"; + regulator-name = "vdd_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vtt_fixed: fixedregulator-vtt { + /* TPS51200 */ + compatible = "regulator-fixed"; + regulator-name = "vtt_fixed"; + vin-supply = <&vdd_ddr>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + leds { + compatible = "gpio-leds"; + + led0 { + label = "beaglebone:green:usr0"; + gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led1 { + label = "beaglebone:green:usr1"; + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led2 { + label = "beaglebone:green:usr2"; + gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "cpu"; + default-state = "off"; + }; + + led3 { + label = "beaglebone:green:usr3"; + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led4 { + label = "beaglebone:green:usr4"; + gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "netdev"; + default-state = "off"; + }; + }; + + hdmi_conn: connector@0 { + compatible = "hdmi-connector"; + label = "hdmi"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_encoder_out>; + }; + }; + }; + + hdmi_enc: encoder@0 { + /* "ti,tpd12s016" software compatible with "ti,tpd12s015" + * no need for individual driver + */ + compatible = "ti,tpd12s015"; + gpios = <0>, + <0>, + <&gpio7 12 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <0x1>; + #size-cells = <0x0>; + + port@0 { + reg = <0x0>; + + hdmi_encoder_in: endpoint@0 { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <0x1>; + + hdmi_encoder_out: endpoint@0 { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; + + emmc_pwrseq: emmc_pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>; + }; + + brcmf_pwrseq: brcmf_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>, /* BT-REG-ON */ + <&gpio3 18 GPIO_ACTIVE_LOW>; /* WL-REG-ON */ + }; + + extcon_usb1: extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + ti,enable-id-detection; + id-gpio = <&gpio3 13 GPIO_ACTIVE_HIGH>; + }; +}; + +&ocp { + pruss1_shmem: pruss_shmem@4b200000 { + status = "okay"; + compatible = "ti,pruss-shmem"; + reg = <0x4b200000 0x020000>; + }; + + pruss2_shmem: pruss_shmem@4b280000 { + status = "okay"; + compatible = "ti,pruss-shmem"; + reg = <0x4b280000 0x020000>; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + tps659038: tps659038@58 { + compatible = "ti,tps659038"; + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + + #interrupt-cells = <2>; + interrupt-controller; + + ti,system-power-controller; + ti,palmas-override-powerhold; + + tps659038_pmic { + compatible = "ti,tps659038-pmic"; + + smps12-in-supply = <&vdd_5v>; + smps3-in-supply = <&vdd_5v>; + smps45-in-supply = <&vdd_5v>; + smps6-in-supply = <&vdd_5v>; + smps7-in-supply = <&vdd_5v>; + mps3-in-supply = <&vdd_5v>; + smps8-in-supply = <&vdd_5v>; + smps9-in-supply = <&vdd_5v>; + ldo1-in-supply = <&vdd_5v>; + ldo2-in-supply = <&vdd_5v>; + ldo3-in-supply = <&vdd_5v>; + ldo4-in-supply = <&vdd_5v>; + ldo9-in-supply = <&vdd_5v>; + ldoln-in-supply = <&vdd_5v>; + ldousb-in-supply = <&vdd_5v>; + ldortc-in-supply = <&vdd_5v>; + + regulators { + vdd_mpu: smps12 { + /* VDD_MPU */ + regulator-name = "smps12"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_ddr: smps3 { + /* VDD_DDR EMIF1 EMIF2 */ + regulator-name = "smps3"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_dspeve: smps45 { + /* VDD_DSPEVE on AM572 */ + regulator-name = "smps45"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_gpu: smps6 { + /* VDD_GPU */ + regulator-name = "smps6"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_core: smps7 { + /* VDD_CORE */ + regulator-name = "smps7"; + regulator-min-microvolt = < 850000>; /*** 1.15V */ + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_iva: smps8 { + /* VDD_IVAHD */ /*** 1.06V */ + regulator-name = "smps8"; + }; + + vdd_3v3: smps9 { + /* VDD_3V3 */ + regulator-name = "smps9"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_sd: ldo1 { + /* VDDSHV8 - VSDMMC */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd_1v8: ldo2 { + /* VDDSH18V */ + regulator-name = "ldo2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_phy_ldo3: ldo3 { + /* R1.3a 572x V1_8PHY_LDO3: USB, SATA */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_phy_ldo4: ldo4 { + /* R1.3a 572x V1_8PHY_LDO4: PCIE, HDMI*/ + regulator-name = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + /* LDO5-8 unused */ + + vdd_rtc: ldo9 { + /* VDD_RTC */ + regulator-name = "ldo9"; + regulator-min-microvolt = < 840000>; + regulator-max-microvolt = <1160000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_pll: ldoln { + /* VDDA_1V8_PLL */ + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldousb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldortc_reg: ldortc { + /* VDDA_RTC */ + regulator-name = "ldortc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + regen1: regen1 { + /* VDD_3V3_ON */ + regulator-name = "regen1"; + regulator-boot-on; + regulator-always-on; + }; + + regen2: regen2 { + /* Needed for PMIC internal resource */ + regulator-name = "regen2"; + regulator-boot-on; + regulator-always-on; + }; + }; + }; + + tps659038_rtc: tps659038_rtc { + compatible = "ti,palmas-rtc"; + interrupt-parent = <&tps659038>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + + tps659038_pwr_button: tps659038_pwr_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps659038>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + ti,palmas-long-press-seconds = <12>; + }; + + tps659038_gpio: tps659038_gpio { + compatible = "ti,palmas-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + /* STMPE811 touch screen controller */ + stmpe811@41 { + compatible = "st,stmpe811"; + reg = <0x41>; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio2>; + interrupt-controller; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + st,mod-12b = <1>; /* 12-bit ADC */ + st,ref-sel = <0>; /* internal ADC reference */ + st,adc-freq = <1>; /* 3.25 MHz ADC clock speed */ + st,sample-time = <4>; /* ADC converstion time: 80 clocks */ + + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x00>; /* mask any channels to be used by touchscreen */ + adc0: iio-device@0 { + #io-channel-cells = <1>; + iio-channels = <&adc0 4>, <&adc0 1>, <&adc0 2>, <&adc0 3>, <&adc0 4>, <&adc0 5>, <&adc0 6>; + iio-channel-names = "AIN0_P9_39", "AIN1_P9_40", "AIN2_P9_37", "AIN3_P9_38", + "AIN4_P9_33", "AIN5_P9_36", "AIN6_P9_35"; + }; + }; + + stmpe_touchscreen { + status = "disabled"; + compatible = "st,stmpe-ts"; + /* 8 sample average control */ + st,ave-ctrl = <3>; + /* 7 length fractional part in z */ + st,fraction-z = <7>; + /* + * 50 mA typical 80 mA max touchscreen drivers + * current limit value + */ + st,i-drive = <1>; + /* 1 ms panel driver settling time */ + st,settling = <3>; + /* 5 ms touch detect interrupt delay */ + st,touch-det-delay = <5>; + }; + + stmpe_gpio { + compatible = "st,stmpe-gpio"; + }; + + stmpe_pwm { + compatible = "st,stmpe-pwm"; + #pwm-cells = <2>; + }; + }; +}; + +&cpu0 { + vdd-supply = <&vdd_mpu>; + voltage-tolerance = <1>; +}; + +&uart1 { + status = "okay"; +}; + +&davinci_mdio { + reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + reset-delay-us = <2>; + + phy0: ethernet-phy@1 { + reg = <4>; + compatible = "ethernet-phy-id004d.d072", + "ethernet-phy-ieee802.3-c22"; + eee-broken-100tx; + eee-broken-1000t; + }; +}; + +&mac { + slaves = <1>; + status = "okay"; +}; + +&cpsw_emac0 { + phy-handle = <&phy0>; + phy-mode = "rgmii"; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vdd_3v3>; + vqmmc-supply = <&vdd_sd>; + bus-width = <4>; + cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */ + + ti,needs-special-reset; + ti,dual-volt; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-ddr50; + sd-uhs-sdr104; + mmc-hs200-1_8v; + cap-sd-highspeed; + cap-mmc-highspeed; + dmas = <&sdma_xbar 61>, <&sdma_xbar 62>; + dma-names = "tx", "rx"; + +}; + +&mmc2 { + status = "okay"; + vmmc-supply = <&vdd_1v8>; + vqmmc-supply = <&vdd_1v8>; + bus-width = <8>; + ti,non-removable; + non-removable; + mmc-pwrseq = <&emmc_pwrseq>; + + ti,needs-special-reset; + dmas = <&sdma_xbar 47>, <&sdma_xbar 48>; + dma-names = "tx", "rx"; + +}; + +&mmc4 { + /* DS: Default speed (DS) up to 25 MHz, including 1- and 4-bit modes (3.3 V signaling). */ + /* HS: High speed up to 50 MHz (3.3 V signaling). */ + /* SDR12: SDR up to 25 MHz (1.8 V signaling). */ + /* SDR25: SDR up to 50 MHz (1.8 V signaling). */ + /* SDR50: SDR up to 100 MHz (1.8 V signaling). */ + /* SDR104: SDR up to 208 MHz (1.8 V signaling) */ + /* DDR50: DDR up to 50 MHz (1.8 V signaling). */ + status = "okay"; + + ti,needs-special-reset; + vmmc-supply = <&vdd_3v3>; + cap-power-off-card; + keep-power-in-suspend; + bus-width = <4>; + ti,non-removable; + non-removable; + no-1-8-v; + max-frequency = <24000000>; + + #address-cells = <1>; + #size-cells = <0>; + mmc-pwrseq = <&brcmf_pwrseq>; + + brcmf: wifi@1 { + status = "okay"; + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + + brcm,sd-head-align = <4>; + brcm,sd_head_align = <4>; + brcm,sd_sgentry_align = <512>; + + interrupt-parent = <&gpio3>; + interrupts = <23 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host-wake"; + }; +}; + +&usb2_phy1 { + phy-supply = <&ldousb_reg>; +}; + +&usb2_phy2 { + phy-supply = <&ldousb_reg>; +}; + +&usb1 { + status = "okay"; + dr_mode = "otg"; +}; + +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&usb2 { + status = "okay"; + dr_mode = "host"; +}; + +&dss { + status = "okay"; + vdda_video-supply = <&vdd_1v8_pll>; +}; + +&hdmi { + status = "okay"; + vdda-supply = <&vdd_1v8_phy_ldo4>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&hdmi_encoder_in>; + }; + }; +}; + +&bandgap { + status = "okay"; +}; + +&mailbox1 { + status = "okay"; +}; + +&mailbox2 { + status = "okay"; +}; + +&mailbox3 { + status = "okay"; +}; + +&mailbox4 { + status = "okay"; +}; + +&mailbox5 { + status = "okay"; +}; + +&mailbox6 { + status = "okay"; +}; + +&mailbox7 { + status = "okay"; +}; + +&mailbox8 { + status = "okay"; +}; + +&mailbox9 { + status = "okay"; +}; + +&mailbox10 { + status = "okay"; +}; + +&mailbox11 { + status = "okay"; +}; + +&mailbox12 { + status = "okay"; +}; + +&mailbox13 { + status = "okay"; +}; + +&cpu_alert0 { + temperature = <55000>; /* milliCelsius */ +}; + +&cpu_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&gpu_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&core_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&dspeve_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&iva_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&sata { + status = "disabled"; +}; + +&sata_phy { + status = "disabled"; +}; + +/* bluetooth */ +&uart6 { + status = "okay"; +}; + +/* cape header stuff */ +&i2c4 { + status = "okay"; + clock-frequency = <100000>; +}; + +&cpu0_opp_table { + opp_slow-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <1060000 850000 1150000>; + opp-supported-hw = <0xFF 0x01>; + opp-suspend; + }; +}; + -- 2.17.1 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 0/2] ARM: dts: am5729: beaglebone-ai: Enable BeagleBone AI @ 2019-11-14 17:09 Caleb Robey 2019-11-14 17:09 ` [PATCH 2/2] ARM: dts: am5729: beaglebone-ai: adding device tree Caleb Robey 0 siblings, 1 reply; 5+ messages in thread From: Caleb Robey @ 2019-11-14 17:09 UTC (permalink / raw) To: linux-omap Cc: Jason Kridner, Lokesh Vutla, Jason Kridner, Faiz Abbas, Andreas Dannenberg, Jean-Jacques Hiblot, Caleb Robey, Praneeth Bajjuri, Andrew F . Davis, Grygorii Strashko, Tom Rini, Rob Herring, Mark Rutland, Benoît Cousson, Tony Lindgren, devicetree, linux-kernel The following patches 1) Minor change to dra7.dtsi 2) Add device tree file for BeagleBone AI update: moved dra7.dtsi changes before dts addition to prevent compilation breaks Please disregard previous similar commits. Email for omap-linux was incorrect. Caleb Robey (2): ARM: dts: am5729: beaglebone-ai: dra7 reqs in dts ARM: dts: am5729: beaglebone-ai: adding device tree arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am5729-beagleboneai.dts | 733 ++++++++++++++++++++++ arch/arm/boot/dts/dra7.dtsi | 2 +- 3 files changed, 735 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts -- 2.17.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 2/2] ARM: dts: am5729: beaglebone-ai: adding device tree 2019-11-14 17:09 [PATCH 0/2] ARM: dts: am5729: beaglebone-ai: Enable BeagleBone AI Caleb Robey @ 2019-11-14 17:09 ` Caleb Robey 2019-11-18 11:33 ` Grygorii Strashko 0 siblings, 1 reply; 5+ messages in thread From: Caleb Robey @ 2019-11-14 17:09 UTC (permalink / raw) To: linux-omap Cc: Jason Kridner, Lokesh Vutla, Jason Kridner, Faiz Abbas, Andreas Dannenberg, Jean-Jacques Hiblot, Caleb Robey, Praneeth Bajjuri, Andrew F . Davis, Grygorii Strashko, Tom Rini, Robert Nelson, Rob Herring, Mark Rutland, Benoît Cousson, Tony Lindgren, devicetree, linux-kernel From: Jason Kridner <jdk@ti.com> BeagleBoard.org BeagleBone AI is an open source hardware single board computer based on the Texas Instruments AM5729 SoC featuring dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital signal processor (DSP), quad-core embedded vision engine (EVE), Arm Cortex-M4 processors, dual programmable realtime unit industrial control subsystems and more. The board features 1GB DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion headers. For more information, refer to: https://beaglebone.ai This patch introduces the BeagleBone AI device tree. Note that the device use the "ti,tpd12s016" component which is software compatible with "ti,tpd12s015". Thus we only use the latter driver. Signed-off-by: Jason Kridner <jdk@ti.com> Cc: Robert Nelson <robertcnelson@gmail.com> Cc: Caleb Robey <c-robey@ti.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am5729-beagleboneai.dts | 733 ++++++++++++++++++++++ 2 files changed, 734 insertions(+) create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b21b3a64641a..b1154dbda73c 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -791,6 +791,7 @@ dtb-$(CONFIG_SOC_DRA7XX) += \ am57xx-beagle-x15.dtb \ am57xx-beagle-x15-revb1.dtb \ am57xx-beagle-x15-revc.dtb \ + am5729-beagleboneai.dtb \ am57xx-cl-som-am57x.dtb \ am57xx-sbc-am57x.dtb \ am572x-idk.dtb \ diff --git a/arch/arm/boot/dts/am5729-beagleboneai.dts b/arch/arm/boot/dts/am5729-beagleboneai.dts new file mode 100644 index 000000000000..76551295290a --- /dev/null +++ b/arch/arm/boot/dts/am5729-beagleboneai.dts @@ -0,0 +1,733 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2014-2019 Texas Instruments Incorporated - http://www.ti.com/ + */ + +/dts-v1/; + +#include "dra74x.dtsi" +#include "am57xx-commercial-grade.dtsi" +#include "dra74x-mmc-iodelay.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/dra.h> + +/ { + model = "BeagleBoard.org BeagleBone AI"; + compatible = "beagleboard.org,am5729-beagleboneai", "ti,am5728", + "ti,dra742", "ti,dra74", "ti,dra7"; + + aliases { + rtc0 = &tps659038_rtc; + rtc1 = &rtc; + display0 = &hdmi_conn; + }; + + chosen { + stdout-path = &uart1; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x80000000 0x0 0x40000000>; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ipu2_memory_region: ipu2-memory@95800000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x95800000 0x0 0x3800000>; + reusable; + status = "okay"; + }; + + dsp1_memory_region: dsp1-memory@99000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x99000000 0x0 0x4000000>; + reusable; + status = "okay"; + }; + + ipu1_memory_region: ipu1-memory@9d000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x9d000000 0x0 0x2000000>; + reusable; + status = "okay"; + }; + + dsp2_memory_region: dsp2-memory@9f000000 { + compatible = "shared-dma-pool"; + reg = <0x0 0x9f000000 0x0 0x800000>; + reusable; + status = "okay"; + }; + + }; + + vdd_adc: gpioregulator-vdd_adc { + compatible = "regulator-gpio"; + regulator-name = "vdd_adc"; + vin-supply = <&vdd_5v>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; + states = <1800000 0 + 3300000 1>; + }; + + vdd_5v: fixedregulator-vdd_5v { + compatible = "regulator-fixed"; + regulator-name = "vdd_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vtt_fixed: fixedregulator-vtt { + /* TPS51200 */ + compatible = "regulator-fixed"; + regulator-name = "vtt_fixed"; + vin-supply = <&vdd_ddr>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + leds { + compatible = "gpio-leds"; + + led0 { + label = "beaglebone:green:usr0"; + gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led1 { + label = "beaglebone:green:usr1"; + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led2 { + label = "beaglebone:green:usr2"; + gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "cpu"; + default-state = "off"; + }; + + led3 { + label = "beaglebone:green:usr3"; + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led4 { + label = "beaglebone:green:usr4"; + gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "netdev"; + default-state = "off"; + }; + }; + + hdmi_conn: connector@0 { + compatible = "hdmi-connector"; + label = "hdmi"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_encoder_out>; + }; + }; + }; + + hdmi_enc: encoder@0 { + /* "ti,tpd12s016" software compatible with "ti,tpd12s015" + * no need for individual driver + */ + compatible = "ti,tpd12s015"; + gpios = <0>, + <0>, + <&gpio7 12 GPIO_ACTIVE_HIGH>; + + ports { + #address-cells = <0x1>; + #size-cells = <0x0>; + + port@0 { + reg = <0x0>; + + hdmi_encoder_in: endpoint@0 { + remote-endpoint = <&hdmi_out>; + }; + }; + + port@1 { + reg = <0x1>; + + hdmi_encoder_out: endpoint@0 { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; + + emmc_pwrseq: emmc_pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>; + }; + + brcmf_pwrseq: brcmf_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>, /* BT-REG-ON */ + <&gpio3 18 GPIO_ACTIVE_LOW>; /* WL-REG-ON */ + }; + + extcon_usb1: extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + ti,enable-id-detection; + id-gpio = <&gpio3 13 GPIO_ACTIVE_HIGH>; + }; +}; + +&ocp { + pruss1_shmem: pruss_shmem@4b200000 { + status = "okay"; + compatible = "ti,pruss-shmem"; + reg = <0x4b200000 0x020000>; + }; + + pruss2_shmem: pruss_shmem@4b280000 { + status = "okay"; + compatible = "ti,pruss-shmem"; + reg = <0x4b280000 0x020000>; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + tps659038: tps659038@58 { + compatible = "ti,tps659038"; + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + + #interrupt-cells = <2>; + interrupt-controller; + + ti,system-power-controller; + ti,palmas-override-powerhold; + + tps659038_pmic { + compatible = "ti,tps659038-pmic"; + + smps12-in-supply = <&vdd_5v>; + smps3-in-supply = <&vdd_5v>; + smps45-in-supply = <&vdd_5v>; + smps6-in-supply = <&vdd_5v>; + smps7-in-supply = <&vdd_5v>; + mps3-in-supply = <&vdd_5v>; + smps8-in-supply = <&vdd_5v>; + smps9-in-supply = <&vdd_5v>; + ldo1-in-supply = <&vdd_5v>; + ldo2-in-supply = <&vdd_5v>; + ldo3-in-supply = <&vdd_5v>; + ldo4-in-supply = <&vdd_5v>; + ldo9-in-supply = <&vdd_5v>; + ldoln-in-supply = <&vdd_5v>; + ldousb-in-supply = <&vdd_5v>; + ldortc-in-supply = <&vdd_5v>; + + regulators { + vdd_mpu: smps12 { + /* VDD_MPU */ + regulator-name = "smps12"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_ddr: smps3 { + /* VDD_DDR EMIF1 EMIF2 */ + regulator-name = "smps3"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_dspeve: smps45 { + /* VDD_DSPEVE on AM572 */ + regulator-name = "smps45"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_gpu: smps6 { + /* VDD_GPU */ + regulator-name = "smps6"; + regulator-min-microvolt = < 850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_core: smps7 { + /* VDD_CORE */ + regulator-name = "smps7"; + regulator-min-microvolt = < 850000>; /*** 1.15V */ + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_iva: smps8 { + /* VDD_IVAHD */ /*** 1.06V */ + regulator-name = "smps8"; + }; + + vdd_3v3: smps9 { + /* VDD_3V3 */ + regulator-name = "smps9"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_sd: ldo1 { + /* VDDSHV8 - VSDMMC */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd_1v8: ldo2 { + /* VDDSH18V */ + regulator-name = "ldo2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_phy_ldo3: ldo3 { + /* R1.3a 572x V1_8PHY_LDO3: USB, SATA */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_phy_ldo4: ldo4 { + /* R1.3a 572x V1_8PHY_LDO4: PCIE, HDMI*/ + regulator-name = "ldo4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + /* LDO5-8 unused */ + + vdd_rtc: ldo9 { + /* VDD_RTC */ + regulator-name = "ldo9"; + regulator-min-microvolt = < 840000>; + regulator-max-microvolt = <1160000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8_pll: ldoln { + /* VDDA_1V8_PLL */ + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldousb"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldortc_reg: ldortc { + /* VDDA_RTC */ + regulator-name = "ldortc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + regen1: regen1 { + /* VDD_3V3_ON */ + regulator-name = "regen1"; + regulator-boot-on; + regulator-always-on; + }; + + regen2: regen2 { + /* Needed for PMIC internal resource */ + regulator-name = "regen2"; + regulator-boot-on; + regulator-always-on; + }; + }; + }; + + tps659038_rtc: tps659038_rtc { + compatible = "ti,palmas-rtc"; + interrupt-parent = <&tps659038>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + + tps659038_pwr_button: tps659038_pwr_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps659038>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + ti,palmas-long-press-seconds = <12>; + }; + + tps659038_gpio: tps659038_gpio { + compatible = "ti,palmas-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + /* STMPE811 touch screen controller */ + stmpe811@41 { + compatible = "st,stmpe811"; + reg = <0x41>; + interrupts = <30 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio2>; + interrupt-controller; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + st,mod-12b = <1>; /* 12-bit ADC */ + st,ref-sel = <0>; /* internal ADC reference */ + st,adc-freq = <1>; /* 3.25 MHz ADC clock speed */ + st,sample-time = <4>; /* ADC converstion time: 80 clocks */ + + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x00>; /* mask any channels to be used by touchscreen */ + adc0: iio-device@0 { + #io-channel-cells = <1>; + iio-channels = <&adc0 4>, <&adc0 1>, <&adc0 2>, <&adc0 3>, <&adc0 4>, <&adc0 5>, <&adc0 6>; + iio-channel-names = "AIN0_P9_39", "AIN1_P9_40", "AIN2_P9_37", "AIN3_P9_38", + "AIN4_P9_33", "AIN5_P9_36", "AIN6_P9_35"; + }; + }; + + stmpe_touchscreen { + status = "disabled"; + compatible = "st,stmpe-ts"; + /* 8 sample average control */ + st,ave-ctrl = <3>; + /* 7 length fractional part in z */ + st,fraction-z = <7>; + /* + * 50 mA typical 80 mA max touchscreen drivers + * current limit value + */ + st,i-drive = <1>; + /* 1 ms panel driver settling time */ + st,settling = <3>; + /* 5 ms touch detect interrupt delay */ + st,touch-det-delay = <5>; + }; + + stmpe_gpio { + compatible = "st,stmpe-gpio"; + }; + + stmpe_pwm { + compatible = "st,stmpe-pwm"; + #pwm-cells = <2>; + }; + }; +}; + +&cpu0 { + vdd-supply = <&vdd_mpu>; + voltage-tolerance = <1>; +}; + +&uart1 { + status = "okay"; +}; + +&davinci_mdio { + reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + reset-delay-us = <2>; + + phy0: ethernet-phy@1 { + reg = <4>; + compatible = "ethernet-phy-id004d.d072", + "ethernet-phy-ieee802.3-c22"; + eee-broken-100tx; + eee-broken-1000t; + }; +}; + +&mac { + slaves = <1>; + status = "okay"; +}; + +&cpsw_emac0 { + phy-handle = <&phy0>; + phy-mode = "rgmii"; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vdd_3v3>; + vqmmc-supply = <&vdd_sd>; + bus-width = <4>; + cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */ + + ti,needs-special-reset; + ti,dual-volt; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-ddr50; + sd-uhs-sdr104; + mmc-hs200-1_8v; + cap-sd-highspeed; + cap-mmc-highspeed; + dmas = <&sdma_xbar 61>, <&sdma_xbar 62>; + dma-names = "tx", "rx"; + +}; + +&mmc2 { + status = "okay"; + vmmc-supply = <&vdd_1v8>; + vqmmc-supply = <&vdd_1v8>; + bus-width = <8>; + ti,non-removable; + non-removable; + mmc-pwrseq = <&emmc_pwrseq>; + + ti,needs-special-reset; + dmas = <&sdma_xbar 47>, <&sdma_xbar 48>; + dma-names = "tx", "rx"; + +}; + +&mmc4 { + /* DS: Default speed (DS) up to 25 MHz, including 1- and 4-bit modes (3.3 V signaling). */ + /* HS: High speed up to 50 MHz (3.3 V signaling). */ + /* SDR12: SDR up to 25 MHz (1.8 V signaling). */ + /* SDR25: SDR up to 50 MHz (1.8 V signaling). */ + /* SDR50: SDR up to 100 MHz (1.8 V signaling). */ + /* SDR104: SDR up to 208 MHz (1.8 V signaling) */ + /* DDR50: DDR up to 50 MHz (1.8 V signaling). */ + status = "okay"; + + ti,needs-special-reset; + vmmc-supply = <&vdd_3v3>; + cap-power-off-card; + keep-power-in-suspend; + bus-width = <4>; + ti,non-removable; + non-removable; + no-1-8-v; + max-frequency = <24000000>; + + #address-cells = <1>; + #size-cells = <0>; + mmc-pwrseq = <&brcmf_pwrseq>; + + brcmf: wifi@1 { + status = "okay"; + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + + brcm,sd-head-align = <4>; + brcm,sd_head_align = <4>; + brcm,sd_sgentry_align = <512>; + + interrupt-parent = <&gpio3>; + interrupts = <23 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "host-wake"; + }; +}; + +&usb2_phy1 { + phy-supply = <&ldousb_reg>; +}; + +&usb2_phy2 { + phy-supply = <&ldousb_reg>; +}; + +&usb1 { + status = "okay"; + dr_mode = "otg"; +}; + +&omap_dwc3_1 { + extcon = <&extcon_usb1>; +}; + +&usb2 { + status = "okay"; + dr_mode = "host"; +}; + +&dss { + status = "okay"; + vdda_video-supply = <&vdd_1v8_pll>; +}; + +&hdmi { + status = "okay"; + vdda-supply = <&vdd_1v8_phy_ldo4>; + + port { + hdmi_out: endpoint { + remote-endpoint = <&hdmi_encoder_in>; + }; + }; +}; + +&bandgap { + status = "okay"; +}; + +&mailbox1 { + status = "okay"; +}; + +&mailbox2 { + status = "okay"; +}; + +&mailbox3 { + status = "okay"; +}; + +&mailbox4 { + status = "okay"; +}; + +&mailbox5 { + status = "okay"; +}; + +&mailbox6 { + status = "okay"; +}; + +&mailbox7 { + status = "okay"; +}; + +&mailbox8 { + status = "okay"; +}; + +&mailbox9 { + status = "okay"; +}; + +&mailbox10 { + status = "okay"; +}; + +&mailbox11 { + status = "okay"; +}; + +&mailbox12 { + status = "okay"; +}; + +&mailbox13 { + status = "okay"; +}; + +&cpu_alert0 { + temperature = <55000>; /* milliCelsius */ +}; + +&cpu_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&gpu_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&core_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&dspeve_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&iva_crit { + temperature = <85000>; /* milliCelsius */ +}; + +&sata { + status = "disabled"; +}; + +&sata_phy { + status = "disabled"; +}; + +/* bluetooth */ +&uart6 { + status = "okay"; +}; + +/* cape header stuff */ +&i2c4 { + status = "okay"; + clock-frequency = <100000>; +}; + +&cpu0_opp_table { + opp_slow-500000000 { + opp-hz = /bits/ 64 <500000000>; + opp-microvolt = <1060000 850000 1150000>; + opp-supported-hw = <0xFF 0x01>; + opp-suspend; + }; +}; + -- 2.17.1 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 2/2] ARM: dts: am5729: beaglebone-ai: adding device tree 2019-11-14 17:09 ` [PATCH 2/2] ARM: dts: am5729: beaglebone-ai: adding device tree Caleb Robey @ 2019-11-18 11:33 ` Grygorii Strashko 0 siblings, 0 replies; 5+ messages in thread From: Grygorii Strashko @ 2019-11-18 11:33 UTC (permalink / raw) To: Caleb Robey, linux-omap Cc: Jason Kridner, Lokesh Vutla, Jason Kridner, Faiz Abbas, Andreas Dannenberg, Jean-Jacques Hiblot, Praneeth Bajjuri, Andrew F . Davis, Tom Rini, Robert Nelson, Rob Herring, Mark Rutland, Benoît Cousson, Tony Lindgren, devicetree, linux-kernel On 14/11/2019 19:09, Caleb Robey wrote: > From: Jason Kridner <jdk@ti.com> > > BeagleBoard.org BeagleBone AI is an open source hardware single > board computer based on the Texas Instruments AM5729 SoC featuring > dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital > signal processor (DSP), quad-core embedded vision engine (EVE), > Arm Cortex-M4 processors, dual programmable realtime unit > industrial control subsystems and more. The board features 1GB > DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, > 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion > headers. > > For more information, refer to: > https://beaglebone.ai > > This patch introduces the BeagleBone AI device tree. > > Note that the device use the "ti,tpd12s016" component which is > software compatible with "ti,tpd12s015". Thus we only use the > latter driver. > > Signed-off-by: Jason Kridner <jdk@ti.com> > Cc: Robert Nelson <robertcnelson@gmail.com> > Cc: Caleb Robey <c-robey@ti.com> > > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/am5729-beagleboneai.dts | 733 ++++++++++++++++++++++ > 2 files changed, 734 insertions(+) > create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index b21b3a64641a..b1154dbda73c 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -791,6 +791,7 @@ dtb-$(CONFIG_SOC_DRA7XX) += \ > am57xx-beagle-x15.dtb \ > am57xx-beagle-x15-revb1.dtb \ [..] > + > +&davinci_mdio { > + reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; > + reset-delay-us = <2>; > + > + phy0: ethernet-phy@1 { > + reg = <4>; > + compatible = "ethernet-phy-id004d.d072", > + "ethernet-phy-ieee802.3-c22"; is it really required to have above compatible prop? It's expected to work without it. > + eee-broken-100tx; > + eee-broken-1000t; > + }; > +}; > + > +&mac { > + slaves = <1>; > + status = "okay"; > +}; > + > +&cpsw_emac0 { > + phy-handle = <&phy0>; > + phy-mode = "rgmii"; > +}; > + [...] -- Best regards, grygorii ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2019-11-18 11:33 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2019-11-14 17:06 [PATCH 0/2] ARM: dts: am5729: beaglebone-ai: Enable BeagleBone AI Caleb Robey 2019-11-14 17:06 ` [PATCH 1/2] ARM: dts: am5729: beaglebone-ai: dra7 reqs in dts Caleb Robey 2019-11-14 17:06 ` [PATCH 2/2] ARM: dts: am5729: beaglebone-ai: adding device tree Caleb Robey -- strict thread matches above, loose matches on Subject: below -- 2019-11-14 17:09 [PATCH 0/2] ARM: dts: am5729: beaglebone-ai: Enable BeagleBone AI Caleb Robey 2019-11-14 17:09 ` [PATCH 2/2] ARM: dts: am5729: beaglebone-ai: adding device tree Caleb Robey 2019-11-18 11:33 ` Grygorii Strashko
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox