Linux on ARM based TI OMAP SoCs
 help / color / mirror / Atom feed
From: Peter Ujfalusi <peter.ujfalusi@ti.com>
To: Matt Ranostay <matt@ranostay.consulting>,
	linux-omap@vger.kernel.org, alsa-devel@alsa-project.org
Cc: Tony Lindgren <tony@atomide.com>
Subject: Re: [PATCH v4] ASoC: omap-mcbsp: Add PM QoS support for McBSP to prevent glitches
Date: Mon, 2 Jan 2017 16:18:16 +0200	[thread overview]
Message-ID: <706677a0-c140-b777-a44f-678ca087cac3@ti.com> (raw)
In-Reply-To: <1482551370-31493-1-git-send-email-matt@ranostay.consulting>

Matt,

On 12/24/2016 05:49 AM, Matt Ranostay wrote:
> We can get audio errors if hitting deeper idle states on omaps:
> 
> [alsa.c:230] error: Fatal problem with alsa output, error -5.
> [audio.c:614] error: Error in writing audio (Input/output error?)!
> 
> This seems to happen with off mode idle enabled as power for the
> whole SoC may get cut off between filling the McBSP fifo using DMA.
> While active DMA blocks deeper idle states in hardware, McBSP
> activity does not seem to do so.
> 
> Basing the QoS latency calculation on the FIFO size, threshold,
> sample rate, and channels.
> 
> Based on the original patch by Tony Lindgren
> Link: https://patchwork.kernel.org/patch/9305867/

I think it would be much better if...
 
> Cc: Tony Lindgren <tony@atomide.com>
> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
> Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
> ---
> 
> Changes from v1:
> * add calculations for latency per number of FIFO locations
> 
> Changes from v2:
> * add missing mcbsp.h header change
> 
> Changes from v3:
> * base the latency calculations on threshold, buffer size, sample
>   rate, and channels
> 
>  sound/soc/omap/mcbsp.c      | 19 +++++++++++++++++++
>  sound/soc/omap/mcbsp.h      |  3 +++
>  sound/soc/omap/omap-mcbsp.c | 21 ++++++++++++++++++++-
>  3 files changed, 42 insertions(+), 1 deletion(-)
> 
> diff --git a/sound/soc/omap/mcbsp.c b/sound/soc/omap/mcbsp.c
> index 06fec5699cc8..8f792e714894 100644
> --- a/sound/soc/omap/mcbsp.c
> +++ b/sound/soc/omap/mcbsp.c
> @@ -25,6 +25,7 @@
>  #include <linux/io.h>
>  #include <linux/slab.h>
>  #include <linux/pm_runtime.h>
> +#include <linux/pm_qos.h>
>  
>  #include <linux/platform_data/asoc-ti-mcbsp.h>
> @@ -640,9 +641,19 @@ void omap_mcbsp_free(struct omap_mcbsp *mcbsp)
>   */
>  void omap_mcbsp_start(struct omap_mcbsp *mcbsp, int tx, int rx)
>  {
> +	struct pm_qos_request *pm_qos_req = &mcbsp->pm_qos_req;
>  	int enable_srg = 0;
>  	u16 w;
>  
> +	/* Prevent omap hardware from hitting off between fifo fills */
> +	if (mcbsp->latency) {
> +		if (pm_qos_request_active(pm_qos_req))
> +			pm_qos_update_request(pm_qos_req, mcbsp->latency);
> +		else
> +			pm_qos_add_request(pm_qos_req, PM_QOS_CPU_DMA_LATENCY,
> +					mcbsp->latency);
> +	}

int stream1 = tx ? SNDRV_PCM_STREAM_PLAYBACK : SNDRV_PCM_STREAM_CAPTURE;
int stream2 = tx ? SNDRV_PCM_STREAM_CAPTURE : SNDRV_PCM_STREAM_PLAYBACK;
unsigned int latency;

if (!mcbsp->latency[stream2] ||
    mcbsp->latency[stream1] < mcbsp->latency[stream2])
	latency = mcbsp->latency[stream1];
else
	latency = mcbsp->latency[stream2];

if (latency) {
	if (pm_qos_request_active(pm_qos_req))
		pm_qos_update_request(pm_qos_req, latency);
	else
		pm_qos_add_request(pm_qos_req, PM_QOS_CPU_DMA_LATENCY,
				   latency);
}

> +
>  	if (mcbsp->st_data)
>  		omap_st_start(mcbsp);
>  
> @@ -731,6 +742,11 @@ void omap_mcbsp_stop(struct omap_mcbsp *mcbsp, int tx, int rx)
>  
>  	if (mcbsp->st_data)
>  		omap_st_stop(mcbsp);
> +
> +	if (mcbsp->active == 1 && pm_qos_request_active(&mcbsp->pm_qos_req)) {
> +		pm_qos_remove_request(&mcbsp->pm_qos_req);
> +		mcbsp->latency = 0;
> +	}

if (pm_qos_request_active(&mcbsp->pm_qos_req)) {
	int stream1 = tx ? SNDRV_PCM_STREAM_PLAYBACK :
			   SNDRV_PCM_STREAM_CAPTURE;
	int stream2 = tx ? SNDRV_PCM_STREAM_CAPTURE :
			   SNDRV_PCM_STREAM_PLAYBACK;

	mcbsp->latency[stream1] = 0;
	if (mcbsp->latency[stream2])
		pm_qos_update_request(pm_qos_req,
				      mcbsp->latency[stream2]);
	else
		pm_qos_remove_request(&mcbsp->pm_qos_req);
}

So we fall back to the qos needed for the remaining stream.

>  }
>  
>  int omap2_mcbsp_set_clks_src(struct omap_mcbsp *mcbsp, u8 fck_src_id)
> @@ -1098,6 +1114,9 @@ int omap_mcbsp_init(struct platform_device *pdev)
>  
>  void omap_mcbsp_cleanup(struct omap_mcbsp *mcbsp)
>  {
> +	if (pm_qos_request_active(&mcbsp->pm_qos_req))
> +		pm_qos_remove_request(&mcbsp->pm_qos_req);
> +
>  	if (mcbsp->pdata->buffer_size)
>  		sysfs_remove_group(&mcbsp->dev->kobj, &additional_attr_group);
>  
> diff --git a/sound/soc/omap/mcbsp.h b/sound/soc/omap/mcbsp.h
> index 61e93b1c185d..d312e72f7979 100644
> --- a/sound/soc/omap/mcbsp.h
> +++ b/sound/soc/omap/mcbsp.h
> @@ -323,8 +323,11 @@ struct omap_mcbsp {
>  
>  	unsigned int fmt;
>  	unsigned int in_freq;
> +	unsigned int latency;

unsigned int latency[2];

>  	int clk_div;
>  	int wlen;
> +
> +	struct pm_qos_request pm_qos_req;
>  };
>  
>  void omap_mcbsp_config(struct omap_mcbsp *mcbsp,
> diff --git a/sound/soc/omap/omap-mcbsp.c b/sound/soc/omap/omap-mcbsp.c
> index d018e966e533..ddaec37fb4c3 100644
> --- a/sound/soc/omap/omap-mcbsp.c
> +++ b/sound/soc/omap/omap-mcbsp.c
> @@ -226,6 +226,7 @@ static int omap_mcbsp_dai_hw_params(struct snd_pcm_substream *substream,
>  	int wlen, channels, wpf;
>  	int pkt_size = 0;
>  	unsigned int format, div, framesize, master;
> +	unsigned int buffer_size = mcbsp->pdata->buffer_size;
>  
>  	dma_data = snd_soc_dai_get_dma_data(cpu_dai, substream);
>  	channels = params_channels(params);
> @@ -240,7 +241,9 @@ static int omap_mcbsp_dai_hw_params(struct snd_pcm_substream *substream,
>  	default:
>  		return -EINVAL;
>  	}
> -	if (mcbsp->pdata->buffer_size) {
> +	if (buffer_size) {
> +		int latency;
> +
>  		if (mcbsp->dma_op_mode == MCBSP_DMA_MODE_THRESHOLD) {
>  			int period_words, max_thrsh;
>  			int divider = 0;
> @@ -271,6 +274,22 @@ static int omap_mcbsp_dai_hw_params(struct snd_pcm_substream *substream,
>  			/* Use packet mode for non mono streams */
>  			pkt_size = channels;
>  		}
> +
> +		latency = ((((buffer_size - pkt_size) / channels) * 1000)
> +				 / (params->rate_num / params->rate_den));
> +
> +		/*
> +		 * Use the lowest QoS latency value for active streams, but
> +		 * this has the disadvantage of using lower than needed latency
> +		 * if an stream with lower QoS ends before one with a higher
> +		 * one. Latency setting only gets reset when all streams
> +		 * complete.
> +		 */
> +		if (latency <= mcbsp->latency)
> +			mcbsp->latency = latency;
> +		else
> +			mcbsp->latency = 0;

mcbsp->latency[substream->stream] = latency;

> +
>  		omap_mcbsp_set_threshold(substream, pkt_size);
>  	}
>  
> 

What do you think?

-- 
Péter

  reply	other threads:[~2017-01-02 14:18 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-12-24  3:49 [PATCH v4] ASoC: omap-mcbsp: Add PM QoS support for McBSP to prevent glitches Matt Ranostay
2017-01-02 14:18 ` Peter Ujfalusi [this message]
2017-01-03  5:10   ` Matt Ranostay

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=706677a0-c140-b777-a44f-678ca087cac3@ti.com \
    --to=peter.ujfalusi@ti.com \
    --cc=alsa-devel@alsa-project.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=matt@ranostay.consulting \
    --cc=tony@atomide.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox