* [parisc-linux] C360 install fails
@ 2001-09-21 13:53 Richard Allen
2001-09-21 20:38 ` Richard Hirst
0 siblings, 1 reply; 4+ messages in thread
From: Richard Allen @ 2001-09-21 13:53 UTC (permalink / raw)
To: parisc-linux
Im using the 0.9.2 CD. I have a C360 (512Meg RAM, 9 Gig hard drive) and
I removed the Graphics card from it and hooked it to a serial console.
The machine boots just fine into the installer. I created that f0 partition,
a small /boot, a swap partition and the remaining disk as /
After that it makes me select a distro (I select sid as the documentation says)
then this hits:
+ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ+ Please Wait +ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ+
| |
| Installing Drivers from |
| /instmnt/debian/dists/sid/main/disks-hppa/current/64/drive |
| rs.tgz... |
| |
ioctl: LOOP_CLR_FD: No such device or address
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001001111111100001100
r0-3 00000000 101fc000 101a5134 2fe06b60
r4-7 00000000 00000000 10337010 10318684m Installation
r8-11 10318010 10318010 1030c010 1030c468
r12-15 10337010 ffffffff 000000fd f0100000
r16-19 10300580 f0000154 f000014c 0000000e
r20-23 0000001f 000003e7 101a5c14 00000000
r24-27 00000000 00000005 ffd05805 1028a010
r28-31 10335810 00000592 10300a80 101213f8
sr0-3 00000000 00000065 00000000 00000000
sr4-7 00000000 00000000 00000000 00000000
IASQ: 00000000 00000000 IAOQ: 101fc2bc 101fc2c0
IIR: 0f40001c ISR: a607ffff IOR: 41505805
ORIG_R28: 00000000
Any hints ?
--
Rikki. -- HP Technical Support, RHCE, RHCX, HP-UX Certified Admin.
-- Solaris 7 Certified Systems and Network Administrator.
Bell Labs Unix -- Reach out and grep someone.
Those who do not understand Unix are condemned to reinvent it, poorly.
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [parisc-linux] C360 install fails 2001-09-21 13:53 [parisc-linux] C360 install fails Richard Allen @ 2001-09-21 20:38 ` Richard Hirst 2001-09-21 21:16 ` Richard Hirst 2001-09-22 16:30 ` Richard Allen 0 siblings, 2 replies; 4+ messages in thread From: Richard Hirst @ 2001-09-21 20:38 UTC (permalink / raw) To: Richard Allen; +Cc: parisc-linux On Fri, Sep 21, 2001 at 01:53:35PM +0000, Richard Allen wrote: > Im using the 0.9.2 CD. I have a C360 (512Meg RAM, 9 Gig hard drive) and > I removed the Graphics card from it and hooked it to a serial console. > > The machine boots just fine into the installer. I created that f0 partition, > a small /boot, a swap partition and the remaining disk as / > > After that it makes me select a distro (I select sid as the documentation says) > then this hits: > > +ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ+ Please Wait +ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ+ > | | > | Installing Drivers from | > | /instmnt/debian/dists/sid/main/disks-hppa/current/64/drive | > | rs.tgz... | One thing that's wrong there, you need to install the 32 bit kernel and modules for a C360. I don't imagine that is the cause of your problem though. Although a C360 will run 64 bit, that isn't completely supported under linux yet. > > ioctl: LOOP_CLR_FD: No such device or address > YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI > PSW: 00000000000001001111111100001100 > r0-3 00000000 101fc000 101a5134 2fe06b60 > r4-7 00000000 00000000 10337010 10318684m Installation > r8-11 10318010 10318010 1030c010 1030c468 > r12-15 10337010 ffffffff 000000fd f0100000 > r16-19 10300580 f0000154 f000014c 0000000e > r20-23 0000001f 000003e7 101a5c14 00000000 > r24-27 00000000 00000005 ffd05805 1028a010 > r28-31 10335810 00000592 10300a80 101213f8 > sr0-3 00000000 00000065 00000000 00000000 > sr4-7 00000000 00000000 00000000 00000000 > > IASQ: 00000000 00000000 IAOQ: 101fc2bc 101fc2c0 > IIR: 0f40001c ISR: a607ffff IOR: 41505805 > ORIG_R28: 00000000 101fc2b8 T _gsc_readb 101fc2cc T _gsc_readw 101a5118 t serial_in 101a5134 t .L687 101a5160 t .L693 101a5160 t serial_out So it looks like serial_in() called _gsc_readb(0xffd05805). On booting, my C360 says 1. Raven U/L2 Dino RS-232 (10) at 0xf2003000, versions 0x6, 0x0, 0x8c, 0x0, 0x0 3. Raven+ w SE FWSCSI Core RS-232 (10) at 0xffd05000, versions 0x56, 0x0, 0x8c, 0x0, 0x0 ... ttyS00 at iomem 0xffd05800 (irq = 154) is a 16550A ... So 0xffd05805 looks like a reasonable address for it to try and access. Does it crash at the same place if you try again? Richard ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [parisc-linux] C360 install fails 2001-09-21 20:38 ` Richard Hirst @ 2001-09-21 21:16 ` Richard Hirst 2001-09-22 16:30 ` Richard Allen 1 sibling, 0 replies; 4+ messages in thread From: Richard Hirst @ 2001-09-21 21:16 UTC (permalink / raw) To: Richard Allen; +Cc: parisc-linux BTW, I just tried an install using a 2.4.9 kernel from about September 13th. And it failed while formatting a 2GB partition: Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912 Writing inode tables: done Writing superbKernel panic: ccio-dma.c: ccio_alloc_range() I/O MMU is out of mapping resources. In interrupt handler - not syncing locks and filesystem accounting information: Hopefully we'll get a fix for that committed before I roll the next ISO. Richard ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [parisc-linux] C360 install fails 2001-09-21 20:38 ` Richard Hirst 2001-09-21 21:16 ` Richard Hirst @ 2001-09-22 16:30 ` Richard Allen 1 sibling, 0 replies; 4+ messages in thread From: Richard Allen @ 2001-09-22 16:30 UTC (permalink / raw) To: Richard Hirst; +Cc: parisc-linux On Fri, Sep 21, 2001 at 09:38:01PM +0100, Richard Hirst wrote: > On booting, my C360 says > > 1. Raven U/L2 Dino RS-232 (10) at 0xf2003000, versions 0x6, 0x0, 0x8c, 0x0, 0x0 > 3. Raven+ w SE FWSCSI Core RS-232 (10) at 0xffd05000, versions 0x56, 0x0, 0x8c, 0x0, 0x0 > ... > ttyS00 at iomem 0xffd05800 (irq = 154) is a 16550A > ... > > So 0xffd05805 looks like a reasonable address for it to try and access. > > Does it crash at the same place if you try again? I didnt give up and I tried all kinds og combinations. I noticed when I was booting off the CD (for the tenth time I think) that the install kernel was 32 bit so I opted for that one a I got further. I actually got so far as it began installing packages, but crashed at random places in the package installation. I then loopback mounted the ISO image and NFS exported it and did the install via NFS and then finally it worked. Then when I had the system up and running I was adding extra packages (telnetd, openssl and openssh) when it crashed again. I now have it in a pretty good state. Ive "apt-get upgrade" every package and installed all the development environment and compiled yesterdays kernel snapshot. bofh:~# uname -a Linux bofh 2.4.9-pa24 #2 Fri Sep 21 20:40:31 UTC 2001 parisc unknown bofh:~# uptime 16:29:35 up 19:10, 1 user, load average: 0.00, 0.00, 0.00 Not a single crash since I booted the new kernel so Im very hopeful that Ive gained some stability. Now to find an area I can contribute to :) -- Rikki. -- HP Technical Support, RHCE, RHCX, HP-UX Certified Admin. -- Solaris 7 Certified Systems and Network Administrator. Bell Labs Unix -- Reach out and grep someone. Those who do not understand Unix are condemned to reinvent it, poorly. ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2001-09-22 16:30 UTC | newest] Thread overview: 4+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2001-09-21 13:53 [parisc-linux] C360 install fails Richard Allen 2001-09-21 20:38 ` Richard Hirst 2001-09-21 21:16 ` Richard Hirst 2001-09-22 16:30 ` Richard Allen
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox