* delay in disc detection causes boot failure
@ 2009-03-30 19:09 AlesD
2009-03-30 22:22 ` Grant Grundler
2009-03-31 10:30 ` Thibaut VARENE
0 siblings, 2 replies; 3+ messages in thread
From: AlesD @ 2009-03-30 19:09 UTC (permalink / raw)
To: linux-parisc
Hello,
I have installed HP-PA port of Debian 5.0 and got into following problem.
The root filesystem is on SW RAID. At the end of kernel initialization
comes reset on SCSI bus. After this reset it takes about 6 seconds
before the attached SCSI disks become "visible" and are detected by
kernel. The initialization process however goes on and during this 6s it
tries to assemble the MD device. Since the discs do not exist yet the
assembly fails and root filesystem is not found. The init script waits 3
minutes before giving up - which would normaly do the trick if the root
was directly in one partition. With RAID (and LVM a top of it) the init
ends with fiasco.
To overcome this I put simple "sleep 30" in the initram scripts - just
before assembly of the MD device. I understand that this issue is more
for Debian, but before reporting ther I'd like to ask here:
1) does anyone here know, why there is the reset/delay during boot, and
2) and if message "Driver 'sd' needs updating - please use bus_type
methods" might have anything to do with this problem.
Thanks in advance Ales Dolecek
Mar 29 08:46:07 czapp005 kernel: imklog 3.18.6, log source = /proc/kmsg
started.
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Initializing cgroup
subsys cpu
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Linux version
2.6.26-1-parisc (Debian 2.6.26-13lenny2) (dannf@debian.org) (gcc version
4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Tue Mar 17 13:15:40
UTC 2009
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] FP[0] enabled: Rev 1
Model 19
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] The 32-bit Kernel has
started...
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] console [ttyB0] enabled
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Initialized PDC Console
for debugging.
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Determining PDC firmware
type: System Map.
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] model 00005dc0 00000481
00000000 00000002 77d75e12 100000f0 00000008 000000b2 000000b2
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] vers 00000203
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] CPUID vers 19 rev 7
(0x00000267)
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] capabilities 0x7
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] model 9000/785/C3700
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Total Memory: 1024 MB
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] initrd: 4f7eb000-4ffee560
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] initrd: reserving
3f7eb000-3ffee560 (mem_max 40000000)
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] On node 0 totalpages: 262144
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Normal zone: 2048
pages used for memmap
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Normal zone: 0 pages
reserved
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Normal zone: 260096
pages, LIFO batch:31
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Movable zone: 0 pages
used for memmap
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] LCD display at
f05d0008,f05d0000 registered
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Built 1 zonelists in
Zone order, mobility grouping on. Total pages: 260096
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Kernel command line:
root=/dev/mapper/safe-system HOME=/ console=tty0 sti=10/6/2/0
sti_font=VGA8x16 TERM=linux palo_kernel=3/vmlinux
Mar 29 08:46:07 czapp005 kernel: [ 0.000000] PID hash table entries:
4096 (order: 12, 16384 bytes)
Mar 29 08:46:07 czapp005 kernel: [17179569.184000] Console: colour dummy
device 160x64
Mar 29 08:46:07 czapp005 kernel: [17179569.192000] console handover:
boot [ttyB0] -> real [tty0]
Mar 29 08:46:07 czapp005 kernel: [17179569.200000] Dentry cache hash
table entries: 131072 (order: 7, 524288 bytes)
Mar 29 08:46:07 czapp005 kernel: [17179569.200000] Inode-cache hash
table entries: 65536 (order: 6, 262144 bytes)
Mar 29 08:46:07 czapp005 kernel: [17179569.248000] Memory:
1025664k/1048576k available (1961k kernel code, 22704k reserved, 882k
data, 224k init)
Mar 29 08:46:07 czapp005 kernel: [17179569.248000] virtual kernel memory
layout:
Mar 29 08:46:07 czapp005 kernel: [17179569.248000] vmalloc :
0x00008000 - 0x0f000000 ( 239 MB)
Mar 29 08:46:07 czapp005 kernel: [17179569.248000] memory :
0x10000000 - 0x50000000 (1024 MB)
Mar 29 08:46:07 czapp005 kernel: [17179569.248000] .init :
0x10410000 - 0x10448000 ( 224 kB)
Mar 29 08:46:07 czapp005 kernel: [17179569.248000] .data :
0x102ea6c0 - 0x103c7000 ( 882 kB)
Mar 29 08:46:07 czapp005 kernel: [17179569.248000] .text :
0x10100000 - 0x102ea6c0 (1961 kB)
Mar 29 08:46:07 czapp005 kernel: [17179569.248000] Calibrating delay
loop... 1495.04 BogoMIPS (lpj=2990080)
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Security Framework
initialized
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] SELinux: Disabled at
boot.
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Capability LSM
initialized
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Mount-cache hash
table entries: 512
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Initializing cgroup
subsys ns
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Initializing cgroup
subsys cpuacct
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Initializing cgroup
subsys devices
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] net_namespace: 648 bytes
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] NET: Registered
protocol family 16
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] EISA bus registered
Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Searching for devices...
Mar 29 08:46:07 czapp005 kernel: [17179569.576000] Found devices:
Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 1. Astro BC Runway
Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b }
Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 2. Elroy PCI Bridge
at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a }
Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 3. Elroy PCI Bridge
at 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a }
Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 4. Elroy PCI Bridge
at 0xfed38000 [10/4] { 13, 0x0, 0x782, 0x0000a }
Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 5. Elroy PCI Bridge
at 0xfed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a }
Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 6. Allegro W2 at
0xfffa0000 [32] { 0, 0x0, 0x5dc, 0x00004 }
Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 7. Memory at
0xfed10200 [49] { 1, 0x0, 0x09c, 0x00009 }
Mar 29 08:46:07 czapp005 kernel: [17179569.576000] Enabling regular
chassis codes support v0.05
Mar 29 08:46:07 czapp005 kernel: [17179569.708000] CPU(s): 1 x PA8700
(PCX-W2) at 750.000000 MHz
Mar 29 08:46:07 czapp005 kernel: [17179569.712000] Whole cache flush
223757 cycles, flushing 3440640 bytes 702747 cycles
Mar 29 08:46:07 czapp005 kernel: [17179569.712000] Setting cache flush
threshold to 600 (1 CPUs online)
Mar 29 08:46:07 czapp005 kernel: [17179569.736000] SBA found Astro 2.1
at 0xfed00000
Mar 29 08:46:07 czapp005 kernel: [17179569.736000] Elroy version TR4.0
(0x5) found at 0xfed30000
Mar 29 08:46:07 czapp005 kernel: [17179569.740000] PCI: Enabled native
mode for NS87415 (pif=0x8f)
Mar 29 08:46:07 czapp005 kernel: [17179569.744000] Elroy version TR4.0
(0x5) found at 0xfed32000
Mar 29 08:46:07 czapp005 kernel: [17179569.744000] Elroy version TR4.0
(0x5) found at 0xfed38000
Mar 29 08:46:07 czapp005 kernel: [17179569.744000] Elroy version TR4.0
(0x5) found at 0xfed3c000
Mar 29 08:46:07 czapp005 kernel: [17179569.744000] iosapic: hpa not
registered for 0000:03:02.0
Mar 29 08:46:07 czapp005 kernel: [17179569.752000] powersw: Soft power
switch at 0xf0400804 enabled.
Mar 29 08:46:07 czapp005 kernel: [17179569.768000] NET: Registered
protocol family 2
Mar 29 08:46:07 czapp005 kernel: [17179569.804000] IP route cache hash
table entries: 32768 (order: 5, 131072 bytes)
Mar 29 08:46:07 czapp005 kernel: [17179569.804000] TCP established hash
table entries: 131072 (order: 8, 1048576 bytes)
Mar 29 08:46:07 czapp005 kernel: [17179569.804000] TCP bind hash table
entries: 65536 (order: 6, 262144 bytes)
Mar 29 08:46:07 czapp005 kernel: [17179569.804000] TCP: Hash tables
configured (established 131072 bind 65536)
Mar 29 08:46:07 czapp005 kernel: [17179569.804000] TCP reno registered
Mar 29 08:46:07 czapp005 kernel: [17179569.816000] NET: Registered
protocol family 1
Mar 29 08:46:07 czapp005 kernel: [17179569.816000] checking if image is
initramfs... it is
Mar 29 08:46:07 czapp005 kernel: [17179571.536000] Freeing initrd
memory: 8205k freed
Mar 29 08:46:07 czapp005 kernel: [17179571.536000] Enabling PDC chassis
warnings support v0.05
Mar 29 08:46:07 czapp005 kernel: [17179571.536000] unwind_init: start =
0x1035de10, end = 0x103850e0, entries = 10029
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] audit: initializing
netlink socket (disabled)
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] type=2000
audit(1238309093.356:1): initialized
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] VFS: Disk quotas
dquot_6.5.1
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] Dquot-cache hash
table entries: 1024 (order 0, 4096 bytes)
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] msgmni has been set
to 2019
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] Block layer SCSI
generic (bsg) driver version 0.4 loaded (major 254)
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] io scheduler noop
registered
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] io scheduler
anticipatory registered
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] io scheduler deadline
registered
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] io scheduler cfq
registered (default)
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Found
NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 67)
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Serial port
1 at 0x3f8
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Serial port
2 at 0x2f8
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Parallel
port at 0x378
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Floppy
controller at 0x3f0
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: ACPI at 0x7e0
Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: USB
regulator enabled
Mar 29 08:46:07 czapp005 kernel: [17179571.544000] PDC Stable Storage
facility v0.30
Mar 29 08:46:07 czapp005 kernel: [17179571.872000] STI GSC/PCI core
graphics driver Version 0.9a
Mar 29 08:46:07 czapp005 kernel: [17179571.872000] STI PCI graphic ROM
found at f7000000 (2048 kB), fb at fa000000 (32 MB)
Mar 29 08:46:07 czapp005 kernel: [17179571.936000] id
35acda30-9a02587, conforms to spec rev. 8.0d
Mar 29 08:46:07 czapp005 kernel: [17179572.068000] graphics card
name: A1299B
Mar 29 08:46:07 czapp005 kernel: [17179572.068000] sticon: Initializing
STI text console.
Mar 29 08:46:07 czapp005 kernel: [17179572.144000] Console: switching to
colour STI console 128x48
Mar 29 08:46:07 czapp005 kernel: [17179572.224000] stifb: 'A1299B' (id:
0x35acda30) not supported.
Mar 29 08:46:07 czapp005 kernel: [17179572.232000] Generic RTC Driver v1.07
Mar 29 08:46:07 czapp005 kernel: [17179572.236000] Serial: 8250/16550
driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Mar 29 08:46:07 czapp005 kernel: [17179572.240000] serial8250: ttyS0 at
I/O 0x3f8 (irq = 3) is a 16550A
Mar 29 08:46:07 czapp005 kernel: [17179572.244000] serial8250: ttyS1 at
I/O 0x2f8 (irq = 4) is a 16550A
Mar 29 08:46:07 czapp005 kernel: [17179572.252000] brd: module loaded
Mar 29 08:46:07 czapp005 kernel: [17179572.256000] mice: PS/2 mouse
device common for all mice
Mar 29 08:46:07 czapp005 kernel: [17179572.264000] TCP cubic registered
Mar 29 08:46:07 czapp005 kernel: [17179572.268000] NET: Registered
protocol family 17
Mar 29 08:46:07 czapp005 kernel: [17179572.272000] registered taskstats
version 1
Mar 29 08:46:07 czapp005 kernel: [17179572.276000] Freeing unused kernel
memory: 224k freed
Mar 29 08:46:07 czapp005 kernel: [17179572.792000] SCSI subsystem
initialized
Mar 29 08:46:07 czapp005 kernel: [17179573.876000] Linux Tulip driver
version 1.1.15-NAPI (Feb 27, 2007)
Mar 29 08:46:07 czapp005 kernel: [17179573.888000] tulip0: no phy info,
aborting mtable build
Mar 29 08:46:07 czapp005 kernel: [17179573.892000] tulip0: MII
transceiver #1 config 1000 status 782d advertising 01e1.
Mar 29 08:46:07 czapp005 kernel: [17179573.904000] eth0: Digital
DS21142/43 Tulip rev 65 at MMIO 0xf4008000, 00:30:6e:21:ac:1a, IRQ 65.
Mar 29 08:46:07 czapp005 kernel: [17179574.108000] usbcore: registered
new interface driver usbfs
Mar 29 08:46:07 czapp005 kernel: [17179574.112000] usbcore: registered
new interface driver hub
Mar 29 08:46:07 czapp005 kernel: [17179574.360000] sym0: <896> rev 0x7
at pci 0000:00:0f.0 irq 68
Mar 29 08:46:07 czapp005 kernel: [17179574.376000] libata version 3.00
loaded.
Mar 29 08:46:07 czapp005 kernel: [17179574.388000] usbcore: registered
new device driver usb
Mar 29 08:46:07 czapp005 kernel: [17179574.400000] ohci_hcd: 2006 August
04 USB 1.1 'Open' Host Controller (OHCI) Driver
Mar 29 08:46:07 czapp005 kernel: [17179574.400000] ohci_hcd: block
sizes: ed 64 td 64
Mar 29 08:46:07 czapp005 kernel: [17179574.408000] sym0: PA-RISC
Firmware, ID 7, Fast-40, SE, parity checking
Mar 29 08:46:07 czapp005 kernel: [17179574.416000] sym0: SCSI BUS has
been reset.
Mar 29 08:46:07 czapp005 kernel: [17179574.424000] sym0: SCSI BUS mode
change from SE to SE.
Mar 29 08:46:07 czapp005 kernel: [17179574.432000] sym0: SCSI BUS has
been reset.
Mar 29 08:46:07 czapp005 kernel: [17179574.436000] scsi0 : sym-2.2.3
Mar 29 08:46:07 czapp005 kernel: [17179574.668000] sym1: <896> rev 0x7
at pci 0000:00:0f.1 irq 68
Mar 29 08:46:07 czapp005 kernel: [17179574.676000] sym1: PA-RISC
Firmware, ID 7, Fast-40, LVD, parity checking
Mar 29 08:46:07 czapp005 kernel: [17179574.680000] sym1: SCSI BUS has
been reset.
Mar 29 08:46:07 czapp005 kernel: [17179574.692000] scsi1 : sym-2.2.3
Mar 29 08:46:07 czapp005 kernel: [17179574.700000] ohci_hcd
0000:00:0e.2: OHCI Host Controller
Mar 29 08:46:07 czapp005 kernel: [17179574.704000] ohci_hcd
0000:00:0e.2: new USB bus registered, assigned bus number 1
Mar 29 08:46:07 czapp005 kernel: [17179574.712000] ohci_hcd
0000:00:0e.2: Using NSC SuperIO setup
Mar 29 08:46:07 czapp005 kernel: [17179574.712000] ohci_hcd
0000:00:0e.2: created debug files
Mar 29 08:46:07 czapp005 kernel: [17179574.712000] ohci_hcd
0000:00:0e.2: irq 1, io mem 0xf4007000
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: OHCI controller state
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: OHCI 1.0, NO legacy support registers
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: control 0x083 HCFS=operational CBSR=3
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: cmdstatus 0x00000 SOC=0
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: intrstatus 0x00000000
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: intrenable 0x8000001a MIE UE RD WDH
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: hcca frame #0000
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: roothub.a 00001003 POTPGT=0 NOCP NDP=3(3)
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: roothub.b 000e0000 PPCM=000e DR=0000
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: roothub.status 00008000 DRWE
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: roothub.portstatus [0] 0x00000100 PPS
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: roothub.portstatus [1] 0x00000100 PPS
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd
0000:00:0e.2: roothub.portstatus [2] 0x00000100 PPS
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] usb usb1: default
language 0x0409
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] usb usb1: uevent
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] usb usb1:
usb_probe_device
Mar 29 08:46:07 czapp005 kernel: [17179574.772000] usb usb1:
configuration #1 chosen from 1 choice
Mar 29 08:46:07 czapp005 kernel: [17179574.776000] usb usb1: adding
1-0:1.0 (config #1, interface 0)
Mar 29 08:46:07 czapp005 kernel: [17179574.776000] usb 1-0:1.0: uevent
Mar 29 08:46:07 czapp005 kernel: [17179574.776000] hub 1-0:1.0:
usb_probe_interface
Mar 29 08:46:07 czapp005 kernel: [17179574.776000] hub 1-0:1.0:
usb_probe_interface - got id
Mar 29 08:46:07 czapp005 kernel: [17179574.776000] hub 1-0:1.0: USB hub
found
Mar 29 08:46:07 czapp005 kernel: [17179574.780000] hub 1-0:1.0: 3 ports
detected
Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0:
standalone hub
Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: ganged
power switching
Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: no
over-current protection
Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: power on
to power good time: 0ms
Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: local
power source is good
Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: enabling
power on all ports
Mar 29 08:46:07 czapp005 kernel: [17179574.888000] usb usb1: New USB
device found, idVendor=1d6b, idProduct=0001
Mar 29 08:46:07 czapp005 kernel: [17179574.892000] usb usb1: New USB
device strings: Mfr=3, Product=2, SerialNumber=1
Mar 29 08:46:07 czapp005 kernel: [17179574.896000] usb usb1: Product:
OHCI Host Controller
Mar 29 08:46:07 czapp005 kernel: [17179574.900000] usb usb1:
Manufacturer: Linux 2.6.26-1-parisc ohci_hcd
Mar 29 08:46:07 czapp005 kernel: [17179574.904000] usb usb1:
SerialNumber: 0000:00:0e.2
Mar 29 08:46:07 czapp005 kernel: [17179574.908000] hub 1-0:1.0: state 7
ports 3 chg 0000 evt 0006
Mar 29 08:46:07 czapp005 kernel: [17179574.908000] ohci_hcd
0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
Mar 29 08:46:07 czapp005 kernel: [17179574.908000] hub 1-0:1.0: port 1,
status 0101, change 0001, 12 Mb/s
Mar 29 08:46:07 czapp005 kernel: [17179574.932000] Uniform
Multi-Platform E-IDE driver
Mar 29 08:46:07 czapp005 kernel: [17179574.936000] ide: Assuming 33MHz
system bus speed for PIO modes; override with idebus=xx
Mar 29 08:46:07 czapp005 kernel: [17179574.948000] NS87415: IDE
controller (0x100b:0x0002 rev 0x03) at PCI slot 0000:00:0e.0
Mar 29 08:46:07 czapp005 kernel: [17179574.952000] NS87415: 100% native
mode on irq 7
Mar 29 08:46:07 czapp005 kernel: [17179574.960000] ide0: BM-DMA at
0x0a00-0x0a07
Mar 29 08:46:07 czapp005 kernel: [17179574.964000] ide1: BM-DMA at
0x0a08-0x0a0f
Mar 29 08:46:07 czapp005 kernel: [17179574.968000] Probing IDE interface
ide0...
Mar 29 08:46:07 czapp005 kernel: [17179575.044000] hub 1-0:1.0:
debounce: port 1: total 100ms stable 100ms status 0x101
Mar 29 08:46:07 czapp005 kernel: [17179575.116000] ohci_hcd
0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
Mar 29 08:46:07 czapp005 kernel: [17179575.172000] usb 1-1: new full
speed USB device using ohci_hcd and address 2
Mar 29 08:46:07 czapp005 kernel: [17179575.248000] ohci_hcd
0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
Mar 29 08:46:07 czapp005 kernel: [17179575.328000] usb 1-1: default
language 0x0409
Mar 29 08:46:07 czapp005 kernel: [17179575.336000] usb 1-1: uevent
Mar 29 08:46:07 czapp005 kernel: [17179575.336000] usb 1-1: usb_probe_device
Mar 29 08:46:07 czapp005 kernel: [17179575.336000] usb 1-1:
configuration #1 chosen from 1 choice
Mar 29 08:46:07 czapp005 kernel: [17179575.340000] usb 1-1: adding
1-1:1.0 (config #1, interface 0)
Mar 29 08:46:07 czapp005 kernel: [17179575.340000] usb 1-1:1.0: uevent
Mar 29 08:46:07 czapp005 kernel: [17179575.340000] usb 1-1: New USB
device found, idVendor=1687, idProduct=0163
Mar 29 08:46:07 czapp005 kernel: [17179575.344000] usb 1-1: New USB
device strings: Mfr=1, Product=2, SerialNumber=3
Mar 29 08:46:07 czapp005 kernel: [17179575.348000] usb 1-1: Product:
USB2.0 FlashDisk
Mar 29 08:46:07 czapp005 kernel: [17179575.352000] usb 1-1:
Manufacturer: Kingmax
Mar 29 08:46:07 czapp005 kernel: [17179575.360000] usb 1-1:
SerialNumber: 020000000001B4
Mar 29 08:46:07 czapp005 kernel: [17179575.364000] ohci_hcd
0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
Mar 29 08:46:07 czapp005 kernel: [17179575.364000] hub 1-0:1.0: port 2,
status 0301, change 0001, 1.5 Mb/s
Mar 29 08:46:07 czapp005 kernel: [17179575.372000] hda: FX4830T, ATAPI
CD/DVD-ROM drive
Mar 29 08:46:07 czapp005 kernel: [17179575.436000] Initializing USB Mass
Storage driver...
Mar 29 08:46:07 czapp005 kernel: [17179575.492000] hub 1-0:1.0:
debounce: port 2: total 100ms stable 100ms status 0x301
Mar 29 08:46:07 czapp005 kernel: [17179575.564000] ohci_hcd
0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA
PPS PES CCS
Mar 29 08:46:07 czapp005 kernel: [17179575.620000] usb 1-2: new low
speed USB device using ohci_hcd and address 3
Mar 29 08:46:07 czapp005 kernel: [17179575.696000] ohci_hcd
0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA
PPS PES CCS
Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: skipped 1
descriptor after interface
Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: skipped 1
descriptor after interface
Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: skipped 1
descriptor after interface
Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: uevent
Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: usb_probe_device
Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2:
configuration #1 chosen from 1 choice
Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2: adding
1-2:1.0 (config #1, interface 0)
Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2:1.0: uevent
Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2: adding
1-2:1.1 (config #1, interface 1)
Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2:1.1: uevent
Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2: adding
1-2:1.2 (config #1, interface 2)
Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2:1.2: uevent
Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2: New USB
device found, idVendor=05e3, idProduct=ffe0
Mar 29 08:46:07 czapp005 kernel: [17179575.792000] usb 1-2: New USB
device strings: Mfr=0, Product=0, SerialNumber=0
Mar 29 08:46:07 czapp005 kernel: [17179575.800000] hub 1-0:1.0: state 7
ports 3 chg 0000 evt 0004
Mar 29 08:46:07 czapp005 kernel: [17179575.832000] usb-storage 1-1:1.0:
usb_probe_interface
Mar 29 08:46:07 czapp005 kernel: [17179575.832000] usb-storage 1-1:1.0:
usb_probe_interface - got id
Mar 29 08:46:07 czapp005 kernel: [17179575.832000] scsi2 : SCSI
emulation for USB Mass Storage devices
Mar 29 08:46:07 czapp005 kernel: [17179575.836000] usbcore: registered
new interface driver usb-storage
Mar 29 08:46:07 czapp005 kernel: [17179575.840000] USB Mass Storage
support registered.
Mar 29 08:46:07 czapp005 kernel: [17179575.848000] usb-storage: device
found at 2
Mar 29 08:46:07 czapp005 kernel: [17179575.848000] usb-storage: waiting
for device to settle before scanning
Mar 29 08:46:07 czapp005 kernel: [17179575.956000] usbcore: registered
new interface driver hiddev
Mar 29 08:46:07 czapp005 kernel: [17179575.960000] usbhid 1-2:1.0:
usb_probe_interface
Mar 29 08:46:07 czapp005 kernel: [17179575.960000] usbhid 1-2:1.0:
usb_probe_interface - got id
Mar 29 08:46:07 czapp005 kernel: [17179576.012000] input: HID 05e3:ffe0
as /class/input/input0
Mar 29 08:46:07 czapp005 kernel: [17179576.028000] input,hidraw0: USB
HID v1.00 Keyboard [HID 05e3:ffe0] on usb-0000:00:0e.2-2
Mar 29 08:46:07 czapp005 kernel: [17179576.032000] usbhid 1-2:1.1:
usb_probe_interface
Mar 29 08:46:07 czapp005 kernel: [17179576.032000] usbhid 1-2:1.1:
usb_probe_interface - got id
Mar 29 08:46:07 czapp005 kernel: [17179576.052000] Probing IDE interface
ide1...
Mar 29 08:46:07 czapp005 kernel: [17179576.064000] input: HID 05e3:ffe0
as /class/input/input1
Mar 29 08:46:07 czapp005 kernel: [17179576.080000] input,hidraw1: USB
HID v1.00 Device [HID 05e3:ffe0] on usb-0000:00:0e.2-2
Mar 29 08:46:07 czapp005 kernel: [17179576.084000] usbhid 1-2:1.2:
usb_probe_interface
Mar 29 08:46:07 czapp005 kernel: [17179576.084000] usbhid 1-2:1.2:
usb_probe_interface - got id
Mar 29 08:46:07 czapp005 kernel: [17179576.100000] input: HID 05e3:ffe0
as /class/input/input2
Mar 29 08:46:07 czapp005 kernel: [17179576.120000] input,hidraw2: USB
HID v1.00 Mouse [HID 05e3:ffe0] on usb-0000:00:0e.2-2
Mar 29 08:46:07 czapp005 kernel: [17179576.124000] usbcore: registered
new interface driver usbhid
Mar 29 08:46:07 czapp005 kernel: [17179576.128000] usbhid: v2.6:USB HID
core driver
Mar 29 08:46:07 czapp005 kernel: [17179576.620000] ide0 at
0xf00-0xf07,0xe02 on irq 7
Mar 29 08:46:07 czapp005 kernel: [17179576.624000] ide1 at
0xd00-0xd07,0xb02 on irq 7
Mar 29 08:46:07 czapp005 kernel: [17179576.712000] hda: ATAPI 48X CD-ROM
drive, 128kB Cache
Mar 29 08:46:07 czapp005 kernel: [17179576.716000] Uniform CD-ROM driver
Revision: 3.20
Mar 29 08:46:07 czapp005 kernel: [17179579.152000] scsi 1:0:5:0:
Direct-Access HP 36.4G ST336706LC HP03 PQ: 0 ANSI: 2
Mar 29 08:46:07 czapp005 kernel: [17179579.160000] target1:0:5: tagged
command queuing enabled, command queue depth 16.
Mar 29 08:46:07 czapp005 kernel: [17179579.164000] target1:0:5:
Beginning Domain Validation
Mar 29 08:46:07 czapp005 kernel: [17179579.168000] target1:0:5:
asynchronous
Mar 29 08:46:07 czapp005 kernel: [17179579.184000] target1:0:5: wide
asynchronous
Mar 29 08:46:07 czapp005 kernel: [17179579.192000] target1:0:5: FAST-40
WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
Mar 29 08:46:07 czapp005 kernel: [17179579.200000] target1:0:5: Domain
Validation skipping write tests
Mar 29 08:46:07 czapp005 kernel: [17179579.208000] target1:0:5: Ending
Domain Validation
Mar 29 08:46:07 czapp005 kernel: [17179579.220000] scsi 1:0:6:0:
Direct-Access HP 36.4G ST336706LC HP03 PQ: 0 ANSI: 2
Mar 29 08:46:07 czapp005 kernel: [17179579.224000] target1:0:6: tagged
command queuing enabled, command queue depth 16.
Mar 29 08:46:07 czapp005 kernel: [17179579.228000] target1:0:6:
Beginning Domain Validation
Mar 29 08:46:07 czapp005 kernel: [17179579.232000] target1:0:6:
asynchronous
Mar 29 08:46:07 czapp005 kernel: [17179579.248000] target1:0:6: wide
asynchronous
Mar 29 08:46:07 czapp005 kernel: [17179579.256000] target1:0:6: FAST-40
WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
Mar 29 08:46:07 czapp005 kernel: [17179579.268000] target1:0:6: Domain
Validation skipping write tests
Mar 29 08:46:07 czapp005 kernel: [17179579.272000] target1:0:6: Ending
Domain Validation
Mar 29 08:46:07 czapp005 kernel: [17179580.848000] usb-storage: device
scan complete
Mar 29 08:46:07 czapp005 kernel: [17179580.852000] scsi 2:0:0:0:
Direct-Access Kingmax USB2.0 FlashDisk 0.00 PQ: 0 ANSI: 2
Mar 29 08:46:07 czapp005 kernel: [17179581.808000] Driver 'sd' needs
updating - please use bus_type methods
Mar 29 08:46:07 czapp005 kernel: [17179581.840000] sd 1:0:5:0: [sda]
71132960 512-byte hardware sectors (36420 MB)
Mar 29 08:46:07 czapp005 kernel: [17179581.844000] sd 1:0:5:0: [sda]
Write Protect is off
Mar 29 08:46:07 czapp005 kernel: [17179581.848000] sd 1:0:5:0: [sda]
Mode Sense: 9f 00 10 08
Mar 29 08:46:07 czapp005 kernel: [17179581.852000] sd 1:0:5:0: [sda]
Write cache: enabled, read cache: enabled, supports DPO and FUA
Mar 29 08:46:07 czapp005 kernel: [17179581.856000] sd 1:0:5:0: [sda]
71132960 512-byte hardware sectors (36420 MB)
Mar 29 08:46:07 czapp005 kernel: [17179581.864000] sd 1:0:5:0: [sda]
Write Protect is off
Mar 29 08:46:07 czapp005 kernel: [17179581.868000] sd 1:0:5:0: [sda]
Mode Sense: 9f 00 10 08
Mar 29 08:46:07 czapp005 kernel: [17179581.868000] sd 1:0:5:0: [sda]
Write cache: enabled, read cache: enabled, supports DPO and FUA
Mar 29 08:46:07 czapp005 kernel: [17179581.876000] sda: sda1 sda2 sda3 sda4
Mar 29 08:46:07 czapp005 kernel: [17179581.884000] sd 1:0:5:0: [sda]
Attached SCSI disk
Mar 29 08:46:07 czapp005 kernel: [17179581.900000] sd 1:0:6:0: [sdb]
71132960 512-byte hardware sectors (36420 MB)
Mar 29 08:46:07 czapp005 kernel: [17179581.908000] sd 1:0:6:0: [sdb]
Write Protect is off
Mar 29 08:46:07 czapp005 kernel: [17179581.912000] sd 1:0:6:0: [sdb]
Mode Sense: 9f 00 10 08
Mar 29 08:46:07 czapp005 kernel: [17179581.912000] sd 1:0:6:0: [sdb]
Write cache: enabled, read cache: enabled, supports DPO and FUA
Mar 29 08:46:07 czapp005 kernel: [17179581.920000] sd 1:0:6:0: [sdb]
71132960 512-byte hardware sectors (36420 MB)
Mar 29 08:46:07 czapp005 kernel: [17179581.924000] sd 1:0:6:0: [sdb]
Write Protect is off
Mar 29 08:46:07 czapp005 kernel: [17179581.928000] sd 1:0:6:0: [sdb]
Mode Sense: 9f 00 10 08
Mar 29 08:46:07 czapp005 kernel: [17179581.932000] sd 1:0:6:0: [sdb]
Write cache: enabled, read cache: enabled, supports DPO and FUA
Mar 29 08:46:07 czapp005 kernel: [17179581.936000] sdb: sdb1 sdb2 sdb3 sdb4
Mar 29 08:46:07 czapp005 kernel: [17179581.944000] sd 1:0:6:0: [sdb]
Attached SCSI disk
Mar 29 08:46:07 czapp005 kernel: [17179581.964000] sd 2:0:0:0: [sdc]
3948543 512-byte hardware sectors (2022 MB)
Mar 29 08:46:07 czapp005 kernel: [17179581.968000] ohci_hcd
0000:00:0e.2: urb 4fa4e960 path 1 ep2in 92120000 cc 9 --> status -181
Mar 29 08:46:07 czapp005 kernel: [17179581.972000] sd 2:0:0:0: [sdc]
Write Protect is off
Mar 29 08:46:07 czapp005 kernel: [17179581.976000] sd 2:0:0:0: [sdc]
Mode Sense: 00 00 00 00
Mar 29 08:46:07 czapp005 kernel: [17179581.976000] sd 2:0:0:0: [sdc]
Assuming drive cache: write through
Mar 29 08:46:07 czapp005 kernel: [17179582.004000] sd 2:0:0:0: [sdc]
3948543 512-byte hardware sectors (2022 MB)
Mar 29 08:46:07 czapp005 kernel: [17179582.008000] ohci_hcd
0000:00:0e.2: urb 4fa4e960 path 1 ep2in 93120000 cc 9 --> status -181
Mar 29 08:46:07 czapp005 kernel: [17179582.012000] sd 2:0:0:0: [sdc]
Write Protect is off
Mar 29 08:46:07 czapp005 kernel: [17179582.016000] sd 2:0:0:0: [sdc]
Mode Sense: 00 00 00 00
Mar 29 08:46:07 czapp005 kernel: [17179582.016000] sd 2:0:0:0: [sdc]
Assuming drive cache: write through
Mar 29 08:46:07 czapp005 kernel: [17179582.020000] sdc: unknown
partition table
Mar 29 08:46:07 czapp005 kernel: [17179582.136000] sd 2:0:0:0: [sdc]
Attached SCSI removable disk
Mar 29 08:46:07 czapp005 kernel: [17179616.956000] md: raid1 personality
registered for level 1
Mar 29 08:46:07 czapp005 kernel: [17179617.028000] md: md0 stopped.
Mar 29 08:46:07 czapp005 kernel: [17179617.204000] md: bind<sdb1>
Mar 29 08:46:07 czapp005 kernel: [17179617.208000] md: bind<sda1>
Mar 29 08:46:07 czapp005 kernel: [17179617.256000] raid1: raid set md0
active with 2 out of 2 mirrors
Mar 29 08:46:07 czapp005 kernel: [17179617.532000] device-mapper:
uevent: version 1.0.3
Mar 29 08:46:07 czapp005 kernel: [17179617.544000] device-mapper: ioctl:
4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
Mar 29 08:46:07 czapp005 kernel: [17179620.184000] kjournald starting.
Commit interval 5 seconds
Mar 29 08:46:07 czapp005 kernel: [17179620.188000] EXT3-fs: mounted
filesystem with ordered data mode.
Mar 29 08:46:07 czapp005 kernel: [17179622.040000] udevd version 125 started
Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb usb1: uevent
Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-0:1.0: uevent
Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-1: uevent
Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-1:1.0: uevent
Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-2: uevent
Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-2:1.0: uevent
Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-2:1.1: uevent
Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-2:1.2: uevent
Mar 29 08:46:07 czapp005 kernel: [17179627.072000] Adding 498004k swap
on /dev/sdb4. Priority:-1 extents:1 across:498004k
Mar 29 08:46:07 czapp005 kernel: [17179637.300000] EXT3 FS on dm-0,
internal journal
Mar 29 08:46:07 czapp005 kernel: [17179638.544000] LASI 82596 driver -
Revision: 1.30
Mar 29 08:46:07 czapp005 kernel: [17179638.588000] loop: module loaded
Mar 29 08:46:07 czapp005 kernel: [17179642.092000] kjournald starting.
Commit interval 5 seconds
Mar 29 08:46:07 czapp005 kernel: [17179642.096000] EXT3 FS on sda3,
internal journal
Mar 29 08:46:07 czapp005 kernel: [17179642.100000] EXT3-fs: mounted
filesystem with ordered data mode.
Mar 29 08:46:07 czapp005 kernel: [17179642.128000] kjournald starting.
Commit interval 5 seconds
Mar 29 08:46:07 czapp005 kernel: [17179642.152000] EXT3 FS on dm-1,
internal journal
Mar 29 08:46:07 czapp005 kernel: [17179642.156000] EXT3-fs: mounted
filesystem with ordered data mode.
Mar 29 08:46:07 czapp005 kernel: [17179642.196000] kjournald starting.
Commit interval 5 seconds
Mar 29 08:46:07 czapp005 kernel: [17179642.200000] EXT3 FS on dm-2,
internal journal
Mar 29 08:46:07 czapp005 kernel: [17179642.204000] EXT3-fs: mounted
filesystem with ordered data mode.
Mar 29 08:46:09 czapp005 kernel: [17179647.156000] eth0: Setting
full-duplex based on MII#1 link partner capability of 41e1.
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: delay in disc detection causes boot failure
2009-03-30 19:09 delay in disc detection causes boot failure AlesD
@ 2009-03-30 22:22 ` Grant Grundler
2009-03-31 10:30 ` Thibaut VARENE
1 sibling, 0 replies; 3+ messages in thread
From: Grant Grundler @ 2009-03-30 22:22 UTC (permalink / raw)
To: AlesD; +Cc: linux-parisc
On Mon, Mar 30, 2009 at 09:09:43PM +0200, AlesD wrote:
> Hello,
>
> I have installed HP-PA port of Debian 5.0 and got into following problem.
>
> The root filesystem is on SW RAID. At the end of kernel initialization
> comes reset on SCSI bus. After this reset it takes about 6 seconds before
> the attached SCSI disks become "visible" and are detected by kernel. The
> initialization process however goes on and during this 6s it tries to
> assemble the MD device. Since the discs do not exist yet the assembly fails
> and root filesystem is not found. The init script waits 3 minutes before
> giving up - which would normaly do the trick if the root was directly in
> one partition. With RAID (and LVM a top of it) the init ends with fiasco.
Is it possible this is due to a change in how the kernel detects devices?
Have you tried with "scsi_mod.scan=sync" boot time parameter?
drivers/scsi/Kconfig says:
config SCSI_SCAN_ASYNC
bool "Asynchronous SCSI scanning"
depends on SCSI
help
The SCSI subsystem can probe for devices while the rest of the
system continues booting, and even probe devices on different
busses in parallel, leading to a significant speed-up.
If you have built SCSI as modules, enabling this option can
be a problem as the devices may not have been found by the
time your system expects them to have been. You can load the
scsi_wait_scan module to ensure that all scans have completed.
If you build your SCSI drivers into the kernel, then everything
will work fine if you say Y here.
You can override this choice by specifying "scsi_mod.scan=sync"
or async on the kernel's command line.
cheers,
grant
>
> To overcome this I put simple "sleep 30" in the initram scripts - just
> before assembly of the MD device. I understand that this issue is more for
> Debian, but before reporting ther I'd like to ask here:
> 1) does anyone here know, why there is the reset/delay during boot, and
> 2) and if message "Driver 'sd' needs updating - please use bus_type
> methods" might have anything to do with this problem.
>
> Thanks in advance Ales Dolecek
>
> Mar 29 08:46:07 czapp005 kernel: imklog 3.18.6, log source = /proc/kmsg
> started.
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Initializing cgroup subsys
> cpu
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Linux version
> 2.6.26-1-parisc (Debian 2.6.26-13lenny2) (dannf@debian.org) (gcc version
> 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Tue Mar 17 13:15:40 UTC
> 2009
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] FP[0] enabled: Rev 1 Model
> 19
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] The 32-bit Kernel has
> started...
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] console [ttyB0] enabled
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Initialized PDC Console for
> debugging.
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Determining PDC firmware
> type: System Map.
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] model 00005dc0 00000481
> 00000000 00000002 77d75e12 100000f0 00000008 000000b2 000000b2
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] vers 00000203
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] CPUID vers 19 rev 7
> (0x00000267)
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] capabilities 0x7
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] model 9000/785/C3700
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Total Memory: 1024 MB
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] initrd: 4f7eb000-4ffee560
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] initrd: reserving
> 3f7eb000-3ffee560 (mem_max 40000000)
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] On node 0 totalpages:
> 262144
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Normal zone: 2048 pages
> used for memmap
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Normal zone: 0 pages
> reserved
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Normal zone: 260096
> pages, LIFO batch:31
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Movable zone: 0 pages
> used for memmap
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] LCD display at
> f05d0008,f05d0000 registered
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Built 1 zonelists in Zone
> order, mobility grouping on. Total pages: 260096
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] Kernel command line:
> root=/dev/mapper/safe-system HOME=/ console=tty0 sti=10/6/2/0
> sti_font=VGA8x16 TERM=linux palo_kernel=3/vmlinux
> Mar 29 08:46:07 czapp005 kernel: [ 0.000000] PID hash table entries:
> 4096 (order: 12, 16384 bytes)
> Mar 29 08:46:07 czapp005 kernel: [17179569.184000] Console: colour dummy
> device 160x64
> Mar 29 08:46:07 czapp005 kernel: [17179569.192000] console handover: boot
> [ttyB0] -> real [tty0]
> Mar 29 08:46:07 czapp005 kernel: [17179569.200000] Dentry cache hash table
> entries: 131072 (order: 7, 524288 bytes)
> Mar 29 08:46:07 czapp005 kernel: [17179569.200000] Inode-cache hash table
> entries: 65536 (order: 6, 262144 bytes)
> Mar 29 08:46:07 czapp005 kernel: [17179569.248000] Memory:
> 1025664k/1048576k available (1961k kernel code, 22704k reserved, 882k data,
> 224k init)
> Mar 29 08:46:07 czapp005 kernel: [17179569.248000] virtual kernel memory
> layout:
> Mar 29 08:46:07 czapp005 kernel: [17179569.248000] vmalloc : 0x00008000
> - 0x0f000000 ( 239 MB)
> Mar 29 08:46:07 czapp005 kernel: [17179569.248000] memory : 0x10000000
> - 0x50000000 (1024 MB)
> Mar 29 08:46:07 czapp005 kernel: [17179569.248000] .init : 0x10410000
> - 0x10448000 ( 224 kB)
> Mar 29 08:46:07 czapp005 kernel: [17179569.248000] .data : 0x102ea6c0
> - 0x103c7000 ( 882 kB)
> Mar 29 08:46:07 czapp005 kernel: [17179569.248000] .text : 0x10100000
> - 0x102ea6c0 (1961 kB)
> Mar 29 08:46:07 czapp005 kernel: [17179569.248000] Calibrating delay
> loop... 1495.04 BogoMIPS (lpj=2990080)
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Security Framework
> initialized
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] SELinux: Disabled at
> boot.
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Capability LSM
> initialized
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Mount-cache hash table
> entries: 512
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Initializing cgroup
> subsys ns
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Initializing cgroup
> subsys cpuacct
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Initializing cgroup
> subsys devices
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] net_namespace: 648 bytes
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] NET: Registered protocol
> family 16
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] EISA bus registered
> Mar 29 08:46:07 czapp005 kernel: [17179569.340000] Searching for devices...
> Mar 29 08:46:07 czapp005 kernel: [17179569.576000] Found devices:
> Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 1. Astro BC Runway Port
> at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b }
> Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 2. Elroy PCI Bridge at
> 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a }
> Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 3. Elroy PCI Bridge at
> 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a }
> Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 4. Elroy PCI Bridge at
> 0xfed38000 [10/4] { 13, 0x0, 0x782, 0x0000a }
> Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 5. Elroy PCI Bridge at
> 0xfed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a }
> Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 6. Allegro W2 at
> 0xfffa0000 [32] { 0, 0x0, 0x5dc, 0x00004 }
> Mar 29 08:46:07 czapp005 kernel: [17179569.576000] 7. Memory at 0xfed10200
> [49] { 1, 0x0, 0x09c, 0x00009 }
> Mar 29 08:46:07 czapp005 kernel: [17179569.576000] Enabling regular chassis
> codes support v0.05
> Mar 29 08:46:07 czapp005 kernel: [17179569.708000] CPU(s): 1 x PA8700
> (PCX-W2) at 750.000000 MHz
> Mar 29 08:46:07 czapp005 kernel: [17179569.712000] Whole cache flush 223757
> cycles, flushing 3440640 bytes 702747 cycles
> Mar 29 08:46:07 czapp005 kernel: [17179569.712000] Setting cache flush
> threshold to 600 (1 CPUs online)
> Mar 29 08:46:07 czapp005 kernel: [17179569.736000] SBA found Astro 2.1 at
> 0xfed00000
> Mar 29 08:46:07 czapp005 kernel: [17179569.736000] Elroy version TR4.0
> (0x5) found at 0xfed30000
> Mar 29 08:46:07 czapp005 kernel: [17179569.740000] PCI: Enabled native mode
> for NS87415 (pif=0x8f)
> Mar 29 08:46:07 czapp005 kernel: [17179569.744000] Elroy version TR4.0
> (0x5) found at 0xfed32000
> Mar 29 08:46:07 czapp005 kernel: [17179569.744000] Elroy version TR4.0
> (0x5) found at 0xfed38000
> Mar 29 08:46:07 czapp005 kernel: [17179569.744000] Elroy version TR4.0
> (0x5) found at 0xfed3c000
> Mar 29 08:46:07 czapp005 kernel: [17179569.744000] iosapic: hpa not
> registered for 0000:03:02.0
> Mar 29 08:46:07 czapp005 kernel: [17179569.752000] powersw: Soft power
> switch at 0xf0400804 enabled.
> Mar 29 08:46:07 czapp005 kernel: [17179569.768000] NET: Registered protocol
> family 2
> Mar 29 08:46:07 czapp005 kernel: [17179569.804000] IP route cache hash
> table entries: 32768 (order: 5, 131072 bytes)
> Mar 29 08:46:07 czapp005 kernel: [17179569.804000] TCP established hash
> table entries: 131072 (order: 8, 1048576 bytes)
> Mar 29 08:46:07 czapp005 kernel: [17179569.804000] TCP bind hash table
> entries: 65536 (order: 6, 262144 bytes)
> Mar 29 08:46:07 czapp005 kernel: [17179569.804000] TCP: Hash tables
> configured (established 131072 bind 65536)
> Mar 29 08:46:07 czapp005 kernel: [17179569.804000] TCP reno registered
> Mar 29 08:46:07 czapp005 kernel: [17179569.816000] NET: Registered protocol
> family 1
> Mar 29 08:46:07 czapp005 kernel: [17179569.816000] checking if image is
> initramfs... it is
> Mar 29 08:46:07 czapp005 kernel: [17179571.536000] Freeing initrd memory:
> 8205k freed
> Mar 29 08:46:07 czapp005 kernel: [17179571.536000] Enabling PDC chassis
> warnings support v0.05
> Mar 29 08:46:07 czapp005 kernel: [17179571.536000] unwind_init: start =
> 0x1035de10, end = 0x103850e0, entries = 10029
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] audit: initializing
> netlink socket (disabled)
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] type=2000
> audit(1238309093.356:1): initialized
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] VFS: Disk quotas
> dquot_6.5.1
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] Dquot-cache hash table
> entries: 1024 (order 0, 4096 bytes)
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] msgmni has been set to
> 2019
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] Block layer SCSI generic
> (bsg) driver version 0.4 loaded (major 254)
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] io scheduler noop
> registered
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] io scheduler
> anticipatory registered
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] io scheduler deadline
> registered
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] io scheduler cfq
> registered (default)
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Found NS87560
> Legacy I/O device at 0000:00:0e.1 (IRQ 67)
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Serial port 1
> at 0x3f8
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Serial port 2
> at 0x2f8
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Parallel port
> at 0x378
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: Floppy
> controller at 0x3f0
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: ACPI at 0x7e0
> Mar 29 08:46:07 czapp005 kernel: [17179571.540000] SuperIO: USB regulator
> enabled
> Mar 29 08:46:07 czapp005 kernel: [17179571.544000] PDC Stable Storage
> facility v0.30
> Mar 29 08:46:07 czapp005 kernel: [17179571.872000] STI GSC/PCI core
> graphics driver Version 0.9a
> Mar 29 08:46:07 czapp005 kernel: [17179571.872000] STI PCI graphic ROM
> found at f7000000 (2048 kB), fb at fa000000 (32 MB)
> Mar 29 08:46:07 czapp005 kernel: [17179571.936000] id 35acda30-9a02587,
> conforms to spec rev. 8.0d
> Mar 29 08:46:07 czapp005 kernel: [17179572.068000] graphics card name:
> A1299B
> Mar 29 08:46:07 czapp005 kernel: [17179572.068000] sticon: Initializing STI
> text console.
> Mar 29 08:46:07 czapp005 kernel: [17179572.144000] Console: switching to
> colour STI console 128x48
> Mar 29 08:46:07 czapp005 kernel: [17179572.224000] stifb: 'A1299B' (id:
> 0x35acda30) not supported.
> Mar 29 08:46:07 czapp005 kernel: [17179572.232000] Generic RTC Driver v1.07
> Mar 29 08:46:07 czapp005 kernel: [17179572.236000] Serial: 8250/16550
> driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> Mar 29 08:46:07 czapp005 kernel: [17179572.240000] serial8250: ttyS0 at I/O
> 0x3f8 (irq = 3) is a 16550A
> Mar 29 08:46:07 czapp005 kernel: [17179572.244000] serial8250: ttyS1 at I/O
> 0x2f8 (irq = 4) is a 16550A
> Mar 29 08:46:07 czapp005 kernel: [17179572.252000] brd: module loaded
> Mar 29 08:46:07 czapp005 kernel: [17179572.256000] mice: PS/2 mouse device
> common for all mice
> Mar 29 08:46:07 czapp005 kernel: [17179572.264000] TCP cubic registered
> Mar 29 08:46:07 czapp005 kernel: [17179572.268000] NET: Registered protocol
> family 17
> Mar 29 08:46:07 czapp005 kernel: [17179572.272000] registered taskstats
> version 1
> Mar 29 08:46:07 czapp005 kernel: [17179572.276000] Freeing unused kernel
> memory: 224k freed
> Mar 29 08:46:07 czapp005 kernel: [17179572.792000] SCSI subsystem
> initialized
> Mar 29 08:46:07 czapp005 kernel: [17179573.876000] Linux Tulip driver
> version 1.1.15-NAPI (Feb 27, 2007)
> Mar 29 08:46:07 czapp005 kernel: [17179573.888000] tulip0: no phy info,
> aborting mtable build
> Mar 29 08:46:07 czapp005 kernel: [17179573.892000] tulip0: MII transceiver
> #1 config 1000 status 782d advertising 01e1.
> Mar 29 08:46:07 czapp005 kernel: [17179573.904000] eth0: Digital DS21142/43
> Tulip rev 65 at MMIO 0xf4008000, 00:30:6e:21:ac:1a, IRQ 65.
> Mar 29 08:46:07 czapp005 kernel: [17179574.108000] usbcore: registered new
> interface driver usbfs
> Mar 29 08:46:07 czapp005 kernel: [17179574.112000] usbcore: registered new
> interface driver hub
> Mar 29 08:46:07 czapp005 kernel: [17179574.360000] sym0: <896> rev 0x7 at
> pci 0000:00:0f.0 irq 68
> Mar 29 08:46:07 czapp005 kernel: [17179574.376000] libata version 3.00
> loaded.
> Mar 29 08:46:07 czapp005 kernel: [17179574.388000] usbcore: registered new
> device driver usb
> Mar 29 08:46:07 czapp005 kernel: [17179574.400000] ohci_hcd: 2006 August 04
> USB 1.1 'Open' Host Controller (OHCI) Driver
> Mar 29 08:46:07 czapp005 kernel: [17179574.400000] ohci_hcd: block sizes:
> ed 64 td 64
> Mar 29 08:46:07 czapp005 kernel: [17179574.408000] sym0: PA-RISC Firmware,
> ID 7, Fast-40, SE, parity checking
> Mar 29 08:46:07 czapp005 kernel: [17179574.416000] sym0: SCSI BUS has been
> reset.
> Mar 29 08:46:07 czapp005 kernel: [17179574.424000] sym0: SCSI BUS mode
> change from SE to SE.
> Mar 29 08:46:07 czapp005 kernel: [17179574.432000] sym0: SCSI BUS has been
> reset.
> Mar 29 08:46:07 czapp005 kernel: [17179574.436000] scsi0 : sym-2.2.3
> Mar 29 08:46:07 czapp005 kernel: [17179574.668000] sym1: <896> rev 0x7 at
> pci 0000:00:0f.1 irq 68
> Mar 29 08:46:07 czapp005 kernel: [17179574.676000] sym1: PA-RISC Firmware,
> ID 7, Fast-40, LVD, parity checking
> Mar 29 08:46:07 czapp005 kernel: [17179574.680000] sym1: SCSI BUS has been
> reset.
> Mar 29 08:46:07 czapp005 kernel: [17179574.692000] scsi1 : sym-2.2.3
> Mar 29 08:46:07 czapp005 kernel: [17179574.700000] ohci_hcd 0000:00:0e.2:
> OHCI Host Controller
> Mar 29 08:46:07 czapp005 kernel: [17179574.704000] ohci_hcd 0000:00:0e.2:
> new USB bus registered, assigned bus number 1
> Mar 29 08:46:07 czapp005 kernel: [17179574.712000] ohci_hcd 0000:00:0e.2:
> Using NSC SuperIO setup
> Mar 29 08:46:07 czapp005 kernel: [17179574.712000] ohci_hcd 0000:00:0e.2:
> created debug files
> Mar 29 08:46:07 czapp005 kernel: [17179574.712000] ohci_hcd 0000:00:0e.2:
> irq 1, io mem 0xf4007000
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> OHCI controller state
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> OHCI 1.0, NO legacy support registers
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> control 0x083 HCFS=operational CBSR=3
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> cmdstatus 0x00000 SOC=0
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> intrstatus 0x00000000
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> intrenable 0x8000001a MIE UE RD WDH
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> hcca frame #0000
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> roothub.a 00001003 POTPGT=0 NOCP NDP=3(3)
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> roothub.b 000e0000 PPCM=000e DR=0000
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> roothub.status 00008000 DRWE
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> roothub.portstatus [0] 0x00000100 PPS
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> roothub.portstatus [1] 0x00000100 PPS
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] ohci_hcd 0000:00:0e.2:
> roothub.portstatus [2] 0x00000100 PPS
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] usb usb1: default
> language 0x0409
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] usb usb1: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] usb usb1:
> usb_probe_device
> Mar 29 08:46:07 czapp005 kernel: [17179574.772000] usb usb1: configuration
> #1 chosen from 1 choice
> Mar 29 08:46:07 czapp005 kernel: [17179574.776000] usb usb1: adding 1-0:1.0
> (config #1, interface 0)
> Mar 29 08:46:07 czapp005 kernel: [17179574.776000] usb 1-0:1.0: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179574.776000] hub 1-0:1.0:
> usb_probe_interface
> Mar 29 08:46:07 czapp005 kernel: [17179574.776000] hub 1-0:1.0:
> usb_probe_interface - got id
> Mar 29 08:46:07 czapp005 kernel: [17179574.776000] hub 1-0:1.0: USB hub
> found
> Mar 29 08:46:07 czapp005 kernel: [17179574.780000] hub 1-0:1.0: 3 ports
> detected
> Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: standalone
> hub
> Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: ganged
> power switching
> Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: no
> over-current protection
> Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: power on to
> power good time: 0ms
> Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: local power
> source is good
> Mar 29 08:46:07 czapp005 kernel: [17179574.784000] hub 1-0:1.0: enabling
> power on all ports
> Mar 29 08:46:07 czapp005 kernel: [17179574.888000] usb usb1: New USB device
> found, idVendor=1d6b, idProduct=0001
> Mar 29 08:46:07 czapp005 kernel: [17179574.892000] usb usb1: New USB device
> strings: Mfr=3, Product=2, SerialNumber=1
> Mar 29 08:46:07 czapp005 kernel: [17179574.896000] usb usb1: Product: OHCI
> Host Controller
> Mar 29 08:46:07 czapp005 kernel: [17179574.900000] usb usb1: Manufacturer:
> Linux 2.6.26-1-parisc ohci_hcd
> Mar 29 08:46:07 czapp005 kernel: [17179574.904000] usb usb1: SerialNumber:
> 0000:00:0e.2
> Mar 29 08:46:07 czapp005 kernel: [17179574.908000] hub 1-0:1.0: state 7
> ports 3 chg 0000 evt 0006
> Mar 29 08:46:07 czapp005 kernel: [17179574.908000] ohci_hcd 0000:00:0e.2:
> GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
> Mar 29 08:46:07 czapp005 kernel: [17179574.908000] hub 1-0:1.0: port 1,
> status 0101, change 0001, 12 Mb/s
> Mar 29 08:46:07 czapp005 kernel: [17179574.932000] Uniform Multi-Platform
> E-IDE driver
> Mar 29 08:46:07 czapp005 kernel: [17179574.936000] ide: Assuming 33MHz
> system bus speed for PIO modes; override with idebus=xx
> Mar 29 08:46:07 czapp005 kernel: [17179574.948000] NS87415: IDE controller
> (0x100b:0x0002 rev 0x03) at PCI slot 0000:00:0e.0
> Mar 29 08:46:07 czapp005 kernel: [17179574.952000] NS87415: 100% native
> mode on irq 7
> Mar 29 08:46:07 czapp005 kernel: [17179574.960000] ide0: BM-DMA at
> 0x0a00-0x0a07
> Mar 29 08:46:07 czapp005 kernel: [17179574.964000] ide1: BM-DMA at
> 0x0a08-0x0a0f
> Mar 29 08:46:07 czapp005 kernel: [17179574.968000] Probing IDE interface
> ide0...
> Mar 29 08:46:07 czapp005 kernel: [17179575.044000] hub 1-0:1.0: debounce:
> port 1: total 100ms stable 100ms status 0x101
> Mar 29 08:46:07 czapp005 kernel: [17179575.116000] ohci_hcd 0000:00:0e.2:
> GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
> Mar 29 08:46:07 czapp005 kernel: [17179575.172000] usb 1-1: new full speed
> USB device using ohci_hcd and address 2
> Mar 29 08:46:07 czapp005 kernel: [17179575.248000] ohci_hcd 0000:00:0e.2:
> GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
> Mar 29 08:46:07 czapp005 kernel: [17179575.328000] usb 1-1: default
> language 0x0409
> Mar 29 08:46:07 czapp005 kernel: [17179575.336000] usb 1-1: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179575.336000] usb 1-1:
> usb_probe_device
> Mar 29 08:46:07 czapp005 kernel: [17179575.336000] usb 1-1: configuration
> #1 chosen from 1 choice
> Mar 29 08:46:07 czapp005 kernel: [17179575.340000] usb 1-1: adding 1-1:1.0
> (config #1, interface 0)
> Mar 29 08:46:07 czapp005 kernel: [17179575.340000] usb 1-1:1.0: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179575.340000] usb 1-1: New USB device
> found, idVendor=1687, idProduct=0163
> Mar 29 08:46:07 czapp005 kernel: [17179575.344000] usb 1-1: New USB device
> strings: Mfr=1, Product=2, SerialNumber=3
> Mar 29 08:46:07 czapp005 kernel: [17179575.348000] usb 1-1: Product: USB2.0
> FlashDisk
> Mar 29 08:46:07 czapp005 kernel: [17179575.352000] usb 1-1: Manufacturer:
> Kingmax
> Mar 29 08:46:07 czapp005 kernel: [17179575.360000] usb 1-1: SerialNumber:
> 020000000001B4
> Mar 29 08:46:07 czapp005 kernel: [17179575.364000] ohci_hcd 0000:00:0e.2:
> GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
> Mar 29 08:46:07 czapp005 kernel: [17179575.364000] hub 1-0:1.0: port 2,
> status 0301, change 0001, 1.5 Mb/s
> Mar 29 08:46:07 czapp005 kernel: [17179575.372000] hda: FX4830T, ATAPI
> CD/DVD-ROM drive
> Mar 29 08:46:07 czapp005 kernel: [17179575.436000] Initializing USB Mass
> Storage driver...
> Mar 29 08:46:07 czapp005 kernel: [17179575.492000] hub 1-0:1.0: debounce:
> port 2: total 100ms stable 100ms status 0x301
> Mar 29 08:46:07 czapp005 kernel: [17179575.564000] ohci_hcd 0000:00:0e.2:
> GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
> Mar 29 08:46:07 czapp005 kernel: [17179575.620000] usb 1-2: new low speed
> USB device using ohci_hcd and address 3
> Mar 29 08:46:07 czapp005 kernel: [17179575.696000] ohci_hcd 0000:00:0e.2:
> GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
> Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: skipped 1
> descriptor after interface
> Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: skipped 1
> descriptor after interface
> Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: skipped 1
> descriptor after interface
> Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2:
> usb_probe_device
> Mar 29 08:46:07 czapp005 kernel: [17179575.780000] usb 1-2: configuration
> #1 chosen from 1 choice
> Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2: adding 1-2:1.0
> (config #1, interface 0)
> Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2:1.0: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2: adding 1-2:1.1
> (config #1, interface 1)
> Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2:1.1: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2: adding 1-2:1.2
> (config #1, interface 2)
> Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2:1.2: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179575.788000] usb 1-2: New USB device
> found, idVendor=05e3, idProduct=ffe0
> Mar 29 08:46:07 czapp005 kernel: [17179575.792000] usb 1-2: New USB device
> strings: Mfr=0, Product=0, SerialNumber=0
> Mar 29 08:46:07 czapp005 kernel: [17179575.800000] hub 1-0:1.0: state 7
> ports 3 chg 0000 evt 0004
> Mar 29 08:46:07 czapp005 kernel: [17179575.832000] usb-storage 1-1:1.0:
> usb_probe_interface
> Mar 29 08:46:07 czapp005 kernel: [17179575.832000] usb-storage 1-1:1.0:
> usb_probe_interface - got id
> Mar 29 08:46:07 czapp005 kernel: [17179575.832000] scsi2 : SCSI emulation
> for USB Mass Storage devices
> Mar 29 08:46:07 czapp005 kernel: [17179575.836000] usbcore: registered new
> interface driver usb-storage
> Mar 29 08:46:07 czapp005 kernel: [17179575.840000] USB Mass Storage support
> registered.
> Mar 29 08:46:07 czapp005 kernel: [17179575.848000] usb-storage: device
> found at 2
> Mar 29 08:46:07 czapp005 kernel: [17179575.848000] usb-storage: waiting for
> device to settle before scanning
> Mar 29 08:46:07 czapp005 kernel: [17179575.956000] usbcore: registered new
> interface driver hiddev
> Mar 29 08:46:07 czapp005 kernel: [17179575.960000] usbhid 1-2:1.0:
> usb_probe_interface
> Mar 29 08:46:07 czapp005 kernel: [17179575.960000] usbhid 1-2:1.0:
> usb_probe_interface - got id
> Mar 29 08:46:07 czapp005 kernel: [17179576.012000] input: HID 05e3:ffe0 as
> /class/input/input0
> Mar 29 08:46:07 czapp005 kernel: [17179576.028000] input,hidraw0: USB HID
> v1.00 Keyboard [HID 05e3:ffe0] on usb-0000:00:0e.2-2
> Mar 29 08:46:07 czapp005 kernel: [17179576.032000] usbhid 1-2:1.1:
> usb_probe_interface
> Mar 29 08:46:07 czapp005 kernel: [17179576.032000] usbhid 1-2:1.1:
> usb_probe_interface - got id
> Mar 29 08:46:07 czapp005 kernel: [17179576.052000] Probing IDE interface
> ide1...
> Mar 29 08:46:07 czapp005 kernel: [17179576.064000] input: HID 05e3:ffe0 as
> /class/input/input1
> Mar 29 08:46:07 czapp005 kernel: [17179576.080000] input,hidraw1: USB HID
> v1.00 Device [HID 05e3:ffe0] on usb-0000:00:0e.2-2
> Mar 29 08:46:07 czapp005 kernel: [17179576.084000] usbhid 1-2:1.2:
> usb_probe_interface
> Mar 29 08:46:07 czapp005 kernel: [17179576.084000] usbhid 1-2:1.2:
> usb_probe_interface - got id
> Mar 29 08:46:07 czapp005 kernel: [17179576.100000] input: HID 05e3:ffe0 as
> /class/input/input2
> Mar 29 08:46:07 czapp005 kernel: [17179576.120000] input,hidraw2: USB HID
> v1.00 Mouse [HID 05e3:ffe0] on usb-0000:00:0e.2-2
> Mar 29 08:46:07 czapp005 kernel: [17179576.124000] usbcore: registered new
> interface driver usbhid
> Mar 29 08:46:07 czapp005 kernel: [17179576.128000] usbhid: v2.6:USB HID
> core driver
> Mar 29 08:46:07 czapp005 kernel: [17179576.620000] ide0 at
> 0xf00-0xf07,0xe02 on irq 7
> Mar 29 08:46:07 czapp005 kernel: [17179576.624000] ide1 at
> 0xd00-0xd07,0xb02 on irq 7
> Mar 29 08:46:07 czapp005 kernel: [17179576.712000] hda: ATAPI 48X CD-ROM
> drive, 128kB Cache
> Mar 29 08:46:07 czapp005 kernel: [17179576.716000] Uniform CD-ROM driver
> Revision: 3.20
> Mar 29 08:46:07 czapp005 kernel: [17179579.152000] scsi 1:0:5:0:
> Direct-Access HP 36.4G ST336706LC HP03 PQ: 0 ANSI: 2
> Mar 29 08:46:07 czapp005 kernel: [17179579.160000] target1:0:5: tagged
> command queuing enabled, command queue depth 16.
> Mar 29 08:46:07 czapp005 kernel: [17179579.164000] target1:0:5: Beginning
> Domain Validation
> Mar 29 08:46:07 czapp005 kernel: [17179579.168000] target1:0:5:
> asynchronous
> Mar 29 08:46:07 czapp005 kernel: [17179579.184000] target1:0:5: wide
> asynchronous
> Mar 29 08:46:07 czapp005 kernel: [17179579.192000] target1:0:5: FAST-40
> WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
> Mar 29 08:46:07 czapp005 kernel: [17179579.200000] target1:0:5: Domain
> Validation skipping write tests
> Mar 29 08:46:07 czapp005 kernel: [17179579.208000] target1:0:5: Ending
> Domain Validation
> Mar 29 08:46:07 czapp005 kernel: [17179579.220000] scsi 1:0:6:0:
> Direct-Access HP 36.4G ST336706LC HP03 PQ: 0 ANSI: 2
> Mar 29 08:46:07 czapp005 kernel: [17179579.224000] target1:0:6: tagged
> command queuing enabled, command queue depth 16.
> Mar 29 08:46:07 czapp005 kernel: [17179579.228000] target1:0:6: Beginning
> Domain Validation
> Mar 29 08:46:07 czapp005 kernel: [17179579.232000] target1:0:6:
> asynchronous
> Mar 29 08:46:07 czapp005 kernel: [17179579.248000] target1:0:6: wide
> asynchronous
> Mar 29 08:46:07 czapp005 kernel: [17179579.256000] target1:0:6: FAST-40
> WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
> Mar 29 08:46:07 czapp005 kernel: [17179579.268000] target1:0:6: Domain
> Validation skipping write tests
> Mar 29 08:46:07 czapp005 kernel: [17179579.272000] target1:0:6: Ending
> Domain Validation
> Mar 29 08:46:07 czapp005 kernel: [17179580.848000] usb-storage: device scan
> complete
> Mar 29 08:46:07 czapp005 kernel: [17179580.852000] scsi 2:0:0:0:
> Direct-Access Kingmax USB2.0 FlashDisk 0.00 PQ: 0 ANSI: 2
> Mar 29 08:46:07 czapp005 kernel: [17179581.808000] Driver 'sd' needs
> updating - please use bus_type methods
> Mar 29 08:46:07 czapp005 kernel: [17179581.840000] sd 1:0:5:0: [sda]
> 71132960 512-byte hardware sectors (36420 MB)
> Mar 29 08:46:07 czapp005 kernel: [17179581.844000] sd 1:0:5:0: [sda] Write
> Protect is off
> Mar 29 08:46:07 czapp005 kernel: [17179581.848000] sd 1:0:5:0: [sda] Mode
> Sense: 9f 00 10 08
> Mar 29 08:46:07 czapp005 kernel: [17179581.852000] sd 1:0:5:0: [sda] Write
> cache: enabled, read cache: enabled, supports DPO and FUA
> Mar 29 08:46:07 czapp005 kernel: [17179581.856000] sd 1:0:5:0: [sda]
> 71132960 512-byte hardware sectors (36420 MB)
> Mar 29 08:46:07 czapp005 kernel: [17179581.864000] sd 1:0:5:0: [sda] Write
> Protect is off
> Mar 29 08:46:07 czapp005 kernel: [17179581.868000] sd 1:0:5:0: [sda] Mode
> Sense: 9f 00 10 08
> Mar 29 08:46:07 czapp005 kernel: [17179581.868000] sd 1:0:5:0: [sda] Write
> cache: enabled, read cache: enabled, supports DPO and FUA
> Mar 29 08:46:07 czapp005 kernel: [17179581.876000] sda: sda1 sda2 sda3
> sda4
> Mar 29 08:46:07 czapp005 kernel: [17179581.884000] sd 1:0:5:0: [sda]
> Attached SCSI disk
> Mar 29 08:46:07 czapp005 kernel: [17179581.900000] sd 1:0:6:0: [sdb]
> 71132960 512-byte hardware sectors (36420 MB)
> Mar 29 08:46:07 czapp005 kernel: [17179581.908000] sd 1:0:6:0: [sdb] Write
> Protect is off
> Mar 29 08:46:07 czapp005 kernel: [17179581.912000] sd 1:0:6:0: [sdb] Mode
> Sense: 9f 00 10 08
> Mar 29 08:46:07 czapp005 kernel: [17179581.912000] sd 1:0:6:0: [sdb] Write
> cache: enabled, read cache: enabled, supports DPO and FUA
> Mar 29 08:46:07 czapp005 kernel: [17179581.920000] sd 1:0:6:0: [sdb]
> 71132960 512-byte hardware sectors (36420 MB)
> Mar 29 08:46:07 czapp005 kernel: [17179581.924000] sd 1:0:6:0: [sdb] Write
> Protect is off
> Mar 29 08:46:07 czapp005 kernel: [17179581.928000] sd 1:0:6:0: [sdb] Mode
> Sense: 9f 00 10 08
> Mar 29 08:46:07 czapp005 kernel: [17179581.932000] sd 1:0:6:0: [sdb] Write
> cache: enabled, read cache: enabled, supports DPO and FUA
> Mar 29 08:46:07 czapp005 kernel: [17179581.936000] sdb: sdb1 sdb2 sdb3
> sdb4
> Mar 29 08:46:07 czapp005 kernel: [17179581.944000] sd 1:0:6:0: [sdb]
> Attached SCSI disk
> Mar 29 08:46:07 czapp005 kernel: [17179581.964000] sd 2:0:0:0: [sdc]
> 3948543 512-byte hardware sectors (2022 MB)
> Mar 29 08:46:07 czapp005 kernel: [17179581.968000] ohci_hcd 0000:00:0e.2:
> urb 4fa4e960 path 1 ep2in 92120000 cc 9 --> status -181
> Mar 29 08:46:07 czapp005 kernel: [17179581.972000] sd 2:0:0:0: [sdc] Write
> Protect is off
> Mar 29 08:46:07 czapp005 kernel: [17179581.976000] sd 2:0:0:0: [sdc] Mode
> Sense: 00 00 00 00
> Mar 29 08:46:07 czapp005 kernel: [17179581.976000] sd 2:0:0:0: [sdc]
> Assuming drive cache: write through
> Mar 29 08:46:07 czapp005 kernel: [17179582.004000] sd 2:0:0:0: [sdc]
> 3948543 512-byte hardware sectors (2022 MB)
> Mar 29 08:46:07 czapp005 kernel: [17179582.008000] ohci_hcd 0000:00:0e.2:
> urb 4fa4e960 path 1 ep2in 93120000 cc 9 --> status -181
> Mar 29 08:46:07 czapp005 kernel: [17179582.012000] sd 2:0:0:0: [sdc] Write
> Protect is off
> Mar 29 08:46:07 czapp005 kernel: [17179582.016000] sd 2:0:0:0: [sdc] Mode
> Sense: 00 00 00 00
> Mar 29 08:46:07 czapp005 kernel: [17179582.016000] sd 2:0:0:0: [sdc]
> Assuming drive cache: write through
> Mar 29 08:46:07 czapp005 kernel: [17179582.020000] sdc: unknown partition
> table
> Mar 29 08:46:07 czapp005 kernel: [17179582.136000] sd 2:0:0:0: [sdc]
> Attached SCSI removable disk
> Mar 29 08:46:07 czapp005 kernel: [17179616.956000] md: raid1 personality
> registered for level 1
> Mar 29 08:46:07 czapp005 kernel: [17179617.028000] md: md0 stopped.
> Mar 29 08:46:07 czapp005 kernel: [17179617.204000] md: bind<sdb1>
> Mar 29 08:46:07 czapp005 kernel: [17179617.208000] md: bind<sda1>
> Mar 29 08:46:07 czapp005 kernel: [17179617.256000] raid1: raid set md0
> active with 2 out of 2 mirrors
> Mar 29 08:46:07 czapp005 kernel: [17179617.532000] device-mapper: uevent:
> version 1.0.3
> Mar 29 08:46:07 czapp005 kernel: [17179617.544000] device-mapper: ioctl:
> 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
> Mar 29 08:46:07 czapp005 kernel: [17179620.184000] kjournald starting.
> Commit interval 5 seconds
> Mar 29 08:46:07 czapp005 kernel: [17179620.188000] EXT3-fs: mounted
> filesystem with ordered data mode.
> Mar 29 08:46:07 czapp005 kernel: [17179622.040000] udevd version 125
> started
> Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb usb1: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-0:1.0: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-1: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-1:1.0: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-2: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-2:1.0: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-2:1.1: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179622.332000] usb 1-2:1.2: uevent
> Mar 29 08:46:07 czapp005 kernel: [17179627.072000] Adding 498004k swap on
> /dev/sdb4. Priority:-1 extents:1 across:498004k
> Mar 29 08:46:07 czapp005 kernel: [17179637.300000] EXT3 FS on dm-0,
> internal journal
> Mar 29 08:46:07 czapp005 kernel: [17179638.544000] LASI 82596 driver -
> Revision: 1.30
> Mar 29 08:46:07 czapp005 kernel: [17179638.588000] loop: module loaded
> Mar 29 08:46:07 czapp005 kernel: [17179642.092000] kjournald starting.
> Commit interval 5 seconds
> Mar 29 08:46:07 czapp005 kernel: [17179642.096000] EXT3 FS on sda3,
> internal journal
> Mar 29 08:46:07 czapp005 kernel: [17179642.100000] EXT3-fs: mounted
> filesystem with ordered data mode.
> Mar 29 08:46:07 czapp005 kernel: [17179642.128000] kjournald starting.
> Commit interval 5 seconds
> Mar 29 08:46:07 czapp005 kernel: [17179642.152000] EXT3 FS on dm-1,
> internal journal
> Mar 29 08:46:07 czapp005 kernel: [17179642.156000] EXT3-fs: mounted
> filesystem with ordered data mode.
> Mar 29 08:46:07 czapp005 kernel: [17179642.196000] kjournald starting.
> Commit interval 5 seconds
> Mar 29 08:46:07 czapp005 kernel: [17179642.200000] EXT3 FS on dm-2,
> internal journal
> Mar 29 08:46:07 czapp005 kernel: [17179642.204000] EXT3-fs: mounted
> filesystem with ordered data mode.
> Mar 29 08:46:09 czapp005 kernel: [17179647.156000] eth0: Setting
> full-duplex based on MII#1 link partner capability of 41e1.
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-parisc" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: delay in disc detection causes boot failure
2009-03-30 19:09 delay in disc detection causes boot failure AlesD
2009-03-30 22:22 ` Grant Grundler
@ 2009-03-31 10:30 ` Thibaut VARENE
1 sibling, 0 replies; 3+ messages in thread
From: Thibaut VARENE @ 2009-03-31 10:30 UTC (permalink / raw)
To: AlesD; +Cc: linux-parisc
2009/3/30 AlesD <ales_d@seznam.cz>:
> Hello,
>
> =C2=A0I have installed HP-PA port of Debian 5.0 and got into followin=
g problem.
>
> The root filesystem is on SW RAID. At the end of kernel initializatio=
n comes
> reset on SCSI bus. After this reset it takes about 6 seconds before t=
he
> attached SCSI disks become "visible" and are detected by kernel. The
> initialization process however goes on and during this 6s it tries to
> assemble the MD device. Since the discs do not exist yet the assembly=
fails
> and root filesystem is not found. The init script waits 3 minutes bef=
ore
> giving up - which would normaly do the trick if the root was directly=
in one
> partition. With RAID (and LVM a top of it) the init ends with fiasco.
>
> To overcome this I put simple "sleep 30" in the initram scripts - jus=
t
> before assembly of the MD device. I understand that this issue is mor=
e for
> Debian, but before reporting ther I'd like to ask here:
> 1) does anyone here know, why there is the reset/delay during boot, a=
nd
> 2) and if message "Driver 'sd' needs updating - please use bus_type m=
ethods"
> might have anything to do with this problem.
I've experienced similar problem with root on raid and Debian kernels.
It's definitely a Debian specific issue, afaict.
HTH
--=20
Thibaut VARENE
http://www.parisc-linux.org/~varenet/
--
To unsubscribe from this list: send the line "unsubscribe linux-parisc"=
in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2009-03-31 10:30 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-03-30 19:09 delay in disc detection causes boot failure AlesD
2009-03-30 22:22 ` Grant Grundler
2009-03-31 10:30 ` Thibaut VARENE
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox