[PATCH AUTOSEL 5.4 021/266] PCI: Allow pci_resize_resource() for devices on root bus

[PATCH AUTOSEL 5.4 021/266] PCI: Allow pci_resize_resource() for devices on root bus

[Sasha Levin]

From: Ard Biesheuvel <ardb@kernel.org>

[ Upstream commit d09ddd8190fbdc07696bf34b548ae15aa1816714 ]

When resizing a BAR, pci_reassign_bridge_resources() is invoked to bring
the bridge windows of parent bridges in line with the new BAR assignment.

This assumes the device whose BAR is being resized lives on a subordinate
bus, but this is not necessarily the case. A device may live on the root
bus, in which case dev->bus->self is NULL, and passing a NULL pci_dev
pointer to pci_reassign_bridge_resources() will cause it to crash.

So let's make the call to pci_reassign_bridge_resources() conditional on
whether dev->bus->self is non-NULL in the first place.

Fixes: 8bb705e3e79d84e7 ("PCI: Add pci_resize_resource() for resizing BARs")
Link: https://lore.kernel.org/r/20200421162256.26887-1-ardb@kernel.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/setup-res.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/pci/setup-res.c b/drivers/pci/setup-res.c
index d8ca40a97693..d21fa04fa44d 100644
--- a/drivers/pci/setup-res.c
+++ b/drivers/pci/setup-res.c
@@ -439,10 +439,11 @@ int pci_resize_resource(struct pci_dev *dev, int resno, int size)
 	res->end = res->start + pci_rebar_size_to_bytes(size) - 1;
 
 	/* Check if the new config works by trying to assign everything. */
-	ret = pci_reassign_bridge_resources(dev->bus->self, res->flags);
-	if (ret)
-		goto error_resize;
-
+	if (dev->bus->self) {
+		ret = pci_reassign_bridge_resources(dev->bus->self, res->flags);
+		if (ret)
+			goto error_resize;
+	}
 	return 0;
 
 error_resize:
-- 
2.25.1

[PATCH AUTOSEL 5.4 043/266] PCI: aardvark: Don't blindly enable ASPM L0s and don't write to read-only register

[Sasha Levin]

From: Pali Rohár <pali@kernel.org>

[ Upstream commit 90c6cb4a355e7befcb557d217d1d8b8bd5875a05 ]

Trying to change Link Status register does not have any effect as this
is a read-only register. Trying to overwrite bits for Negotiated Link
Width does not make sense.

In future proper change of link width can be done via Lane Count Select
bits in PCIe Control 0 register.

Trying to unconditionally enable ASPM L0s via ASPM Control bits in Link
Control register is wrong. There should be at least some detection if
endpoint supports L0s as isn't mandatory.

Moreover ASPM Control bits in Link Control register are controlled by
pcie/aspm.c code which sets it according to system ASPM settings,
immediately after aardvark driver probes. So setting these bits by
aardvark driver has no long running effect.

Remove code which touches ASPM L0s bits from this driver and let
kernel's ASPM implementation to set ASPM state properly.

Some users are reporting issues that this code is problematic for some
Intel wifi cards and removing it fixes them, see e.g.:
https://bugzilla.kernel.org/show_bug.cgi?id=196339

If problems with Intel wifi cards occur even after this commit, then
pcie/aspm.c code could be modified / hooked to not enable ASPM L0s state
for affected problematic cards.

Link: https://lore.kernel.org/r/20200430080625.26070-3-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/pci-aardvark.c | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/drivers/pci/controller/pci-aardvark.c b/drivers/pci/controller/pci-aardvark.c
index 97245e076548..f2481e80e272 100644
--- a/drivers/pci/controller/pci-aardvark.c
+++ b/drivers/pci/controller/pci-aardvark.c
@@ -344,10 +344,6 @@ static void advk_pcie_setup_hw(struct advk_pcie *pcie)
 
 	advk_pcie_wait_for_link(pcie);
 
-	reg = PCIE_CORE_LINK_L0S_ENTRY |
-		(1 << PCIE_CORE_LINK_WIDTH_SHIFT);
-	advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
-
 	reg = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG);
 	reg |= PCIE_CORE_CMD_MEM_ACCESS_EN |
 		PCIE_CORE_CMD_IO_ACCESS_EN |
-- 
2.25.1

[PATCH AUTOSEL 5.4 050/266] PCI: pci-bridge-emul: Fix PCIe bit conflicts

[Sasha Levin]

From: Jon Derrick <jonathan.derrick@intel.com>

[ Upstream commit c88d19181771bd189147681ef38fc1533ebeff4c ]

This patch fixes two bit conflicts in the pci-bridge-emul driver:

1. Bit 3 of Device Status (19 of Device Control) is marked as both
   Write-1-to-Clear and Read-Only. It should be Write-1-to-Clear.
   The Read-Only and Reserved bitmasks are shifted by 1 bit due to this
   error.

2. Bit 12 of Slot Control is marked as both Read-Write and Reserved.
   It should be Read-Write.

Link: https://lore.kernel.org/r/20200511162117.6674-2-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/pci-bridge-emul.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/pci/pci-bridge-emul.c b/drivers/pci/pci-bridge-emul.c
index 5fd90105510d..d3b6b9a05618 100644
--- a/drivers/pci/pci-bridge-emul.c
+++ b/drivers/pci/pci-bridge-emul.c
@@ -195,8 +195,8 @@ static const struct pci_bridge_reg_behavior pcie_cap_regs_behavior[] = {
 		 * RO, the rest is reserved
 		 */
 		.w1c = GENMASK(19, 16),
-		.ro = GENMASK(20, 19),
-		.rsvd = GENMASK(31, 21),
+		.ro = GENMASK(21, 20),
+		.rsvd = GENMASK(31, 22),
 	},
 
 	[PCI_EXP_LNKCAP / 4] = {
@@ -236,7 +236,7 @@ static const struct pci_bridge_reg_behavior pcie_cap_regs_behavior[] = {
 			PCI_EXP_SLTSTA_CC | PCI_EXP_SLTSTA_DLLSC) << 16,
 		.ro = (PCI_EXP_SLTSTA_MRLSS | PCI_EXP_SLTSTA_PDS |
 		       PCI_EXP_SLTSTA_EIS) << 16,
-		.rsvd = GENMASK(15, 12) | (GENMASK(15, 9) << 16),
+		.rsvd = GENMASK(15, 13) | (GENMASK(15, 9) << 16),
 	},
 
 	[PCI_EXP_RTCTL / 4] = {
-- 
2.25.1

[PATCH AUTOSEL 5.4 064/266] PCI: vmd: Filter resource type bits from shadow register

[Sasha Levin]

From: Jon Derrick <jonathan.derrick@intel.com>

[ Upstream commit 3e5095eebe015d5a4d566aa5e03c8621add5f0a7 ]

Versions of VMD with the Host Physical Address shadow register use this
register to calculate the bus address offset needed to do guest
passthrough of the domain. This register shadows the Host Physical
Address registers including the resource type bits. After calculating
the offset, the extra resource type bits lead to the VMD resources being
over-provisioned at the front and under-provisioned at the back.

Example:
pci 10000:80:02.0: reg 0x10: [mem 0xf801fffc-0xf803fffb 64bit]

Expected:
pci 10000:80:02.0: reg 0x10: [mem 0xf8020000-0xf803ffff 64bit]

If other devices are mapped in the over-provisioned front, it could lead
to resource conflict issues with VMD or those devices.

Link: https://lore.kernel.org/r/20200528030240.16024-3-jonathan.derrick@intel.com
Fixes: a1a30170138c9 ("PCI: vmd: Fix shadow offsets to reflect spec changes")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/vmd.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/controller/vmd.c b/drivers/pci/controller/vmd.c
index a35d3f3996d7..0310fe367e01 100644
--- a/drivers/pci/controller/vmd.c
+++ b/drivers/pci/controller/vmd.c
@@ -593,9 +593,11 @@ static int vmd_enable_domain(struct vmd_dev *vmd, unsigned long features)
 			if (!membar2)
 				return -ENOMEM;
 			offset[0] = vmd->dev->resource[VMD_MEMBAR1].start -
-					readq(membar2 + MB2_SHADOW_OFFSET);
+					(readq(membar2 + MB2_SHADOW_OFFSET) &
+					 PCI_BASE_ADDRESS_MEM_MASK);
 			offset[1] = vmd->dev->resource[VMD_MEMBAR2].start -
-					readq(membar2 + MB2_SHADOW_OFFSET + 8);
+					(readq(membar2 + MB2_SHADOW_OFFSET + 8) &
+					 PCI_BASE_ADDRESS_MEM_MASK);
 			pci_iounmap(vmd->dev, membar2);
 		}
 	}
-- 
2.25.1

[PATCH AUTOSEL 5.4 120/266] PCI: v3-semi: Fix a memory leak in v3_pci_probe() error handling paths

[Sasha Levin]

From: Christophe JAILLET <christophe.jaillet@wanadoo.fr>

[ Upstream commit bca718988b9008d0d5f504e2d318178fc84958c1 ]

If we fails somewhere in 'v3_pci_probe()', we need to free 'host'.

Use the managed version of 'pci_alloc_host_bridge()' to do that easily.
The use of managed resources is already widely used in this driver.

Link: https://lore.kernel.org/r/20200418081637.1585-1-christophe.jaillet@wanadoo.fr
Fixes: 68a15eb7bd0c ("PCI: v3-semi: Add V3 Semiconductor PCI host driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/pci-v3-semi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pci/controller/pci-v3-semi.c b/drivers/pci/controller/pci-v3-semi.c
index d219404bad92..9a86bb7448ac 100644
--- a/drivers/pci/controller/pci-v3-semi.c
+++ b/drivers/pci/controller/pci-v3-semi.c
@@ -743,7 +743,7 @@ static int v3_pci_probe(struct platform_device *pdev)
 	int ret;
 	LIST_HEAD(res);
 
-	host = pci_alloc_host_bridge(sizeof(*v3));
+	host = devm_pci_alloc_host_bridge(dev, sizeof(*v3));
 	if (!host)
 		return -ENOMEM;
 
-- 
2.25.1

[PATCH AUTOSEL 5.4 124/266] PCI: rcar: Fix incorrect programming of OB windows

[Sasha Levin]

From: Andrew Murray <andrew.murray@arm.com>

[ Upstream commit 2b9f217433e31d125fb697ca7974d3de3ecc3e92 ]

The outbound windows (PCIEPAUR(x), PCIEPALR(x)) describe a mapping between
a CPU address (which is determined by the window number 'x') and a
programmed PCI address - Thus allowing the controller to translate CPU
accesses into PCI accesses.

However the existing code incorrectly writes the CPU address - lets fix
this by writing the PCI address instead.

For memory transactions, existing DT users describe a 1:1 identity mapping
and thus this change should have no effect. However the same isn't true for
I/O.

Link: https://lore.kernel.org/r/20191004132941.6660-1-andrew.murray@arm.com
Fixes: c25da4778803 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/pcie-rcar.c | 9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/pci/controller/pcie-rcar.c b/drivers/pci/controller/pcie-rcar.c
index 1ad0b56f11b4..04114352d0e7 100644
--- a/drivers/pci/controller/pcie-rcar.c
+++ b/drivers/pci/controller/pcie-rcar.c
@@ -335,11 +335,12 @@ static struct pci_ops rcar_pcie_ops = {
 };
 
 static void rcar_pcie_setup_window(int win, struct rcar_pcie *pcie,
-				   struct resource *res)
+				   struct resource_entry *window)
 {
 	/* Setup PCIe address space mappings for each resource */
 	resource_size_t size;
 	resource_size_t res_start;
+	struct resource *res = window->res;
 	u32 mask;
 
 	rcar_pci_write_reg(pcie, 0x00000000, PCIEPTCTLR(win));
@@ -353,9 +354,9 @@ static void rcar_pcie_setup_window(int win, struct rcar_pcie *pcie,
 	rcar_pci_write_reg(pcie, mask << 7, PCIEPAMR(win));
 
 	if (res->flags & IORESOURCE_IO)
-		res_start = pci_pio_to_address(res->start);
+		res_start = pci_pio_to_address(res->start) - window->offset;
 	else
-		res_start = res->start;
+		res_start = res->start - window->offset;
 
 	rcar_pci_write_reg(pcie, upper_32_bits(res_start), PCIEPAUR(win));
 	rcar_pci_write_reg(pcie, lower_32_bits(res_start) & ~0x7F,
@@ -384,7 +385,7 @@ static int rcar_pcie_setup(struct list_head *resource, struct rcar_pcie *pci)
 		switch (resource_type(res)) {
 		case IORESOURCE_IO:
 		case IORESOURCE_MEM:
-			rcar_pcie_setup_window(i, pci, res);
+			rcar_pcie_setup_window(i, pci, win);
 			i++;
 			break;
 		case IORESOURCE_BUS:
-- 
2.25.1

[PATCH AUTOSEL 5.4 125/266] PCI/ASPM: Allow ASPM on links to PCIe-to-PCI/PCI-X Bridges

[Sasha Levin]

From: Kai-Heng Feng <kai.heng.feng@canonical.com>

[ Upstream commit 66ff14e59e8a30690755b08bc3042359703fb07a ]

7d715a6c1ae5 ("PCI: add PCI Express ASPM support") added the ability for
Linux to enable ASPM, but for some undocumented reason, it didn't enable
ASPM on links where the downstream component is a PCIe-to-PCI/PCI-X Bridge.

Remove this exclusion so we can enable ASPM on these links.

The Dell OptiPlex 7080 mentioned in the bugzilla has a TI XIO2001
PCIe-to-PCI Bridge.  Enabling ASPM on the link leading to it allows the
Intel SoC to enter deeper Package C-states, which is a significant power
savings.

[bhelgaas: commit log]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207571
Link: https://lore.kernel.org/r/20200505173423.26968-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/pcie/aspm.c | 10 ----------
 1 file changed, 10 deletions(-)

diff --git a/drivers/pci/pcie/aspm.c b/drivers/pci/pcie/aspm.c
index 5a1bbf2cb7e9..4a0ec34062d6 100644
--- a/drivers/pci/pcie/aspm.c
+++ b/drivers/pci/pcie/aspm.c
@@ -628,16 +628,6 @@ static void pcie_aspm_cap_init(struct pcie_link_state *link, int blacklist)
 
 	/* Setup initial capable state. Will be updated later */
 	link->aspm_capable = link->aspm_support;
-	/*
-	 * If the downstream component has pci bridge function, don't
-	 * do ASPM for now.
-	 */
-	list_for_each_entry(child, &linkbus->devices, bus_list) {
-		if (pci_pcie_type(child) == PCI_EXP_TYPE_PCI_BRIDGE) {
-			link->aspm_disable = ASPM_STATE_ALL;
-			break;
-		}
-	}
 
 	/* Get and check endpoint acceptable latencies */
 	list_for_each_entry(child, &linkbus->devices, bus_list) {
-- 
2.25.1

[PATCH AUTOSEL 5.4 141/266] PCI: Fix pci_register_host_bridge() device_register() error handling

[Sasha Levin]

From: Rob Herring <robh@kernel.org>

[ Upstream commit 1b54ae8327a4d630111c8d88ba7906483ec6010b ]

If device_register() has an error, we should bail out of
pci_register_host_bridge() rather than continuing on.

Fixes: 37d6a0a6f470 ("PCI: Add pci_register_host_bridge() interface")
Link: https://lore.kernel.org/r/20200513223859.11295-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/probe.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index d3033873395d..e1e61b9dd066 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -867,9 +867,10 @@ static int pci_register_host_bridge(struct pci_host_bridge *bridge)
 		goto free;
 
 	err = device_register(&bridge->dev);
-	if (err)
+	if (err) {
 		put_device(&bridge->dev);
-
+		goto free;
+	}
 	bus->bridge = get_device(&bridge->dev);
 	device_enable_async_suspend(bus->bridge);
 	pci_set_bus_of_node(bus);
-- 
2.25.1

[PATCH AUTOSEL 5.4 147/266] PCI/PM: Assume ports without DLL Link Active train links in 100 ms

[Sasha Levin]

From: Mika Westerberg <mika.westerberg@linux.intel.com>

[ Upstream commit ec411e02b7a2e785a4ed9ed283207cd14f48699d ]

Kai-Heng Feng reported that it takes a long time (> 1 s) to resume
Thunderbolt-connected devices from both runtime suspend and system sleep
(s2idle).

This was because some Downstream Ports that support > 5 GT/s do not also
support Data Link Layer Link Active reporting.  Per PCIe r5.0 sec 6.6.1:

  With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
  software must wait a minimum of 100 ms after Link training completes
  before sending a Configuration Request to the device immediately below
  that Port. Software can determine when Link training completes by polling
  the Data Link Layer Link Active bit or by setting up an associated
  interrupt (see Section 6.7.3.3).

Sec 7.5.3.6 requires such Ports to support DLL Link Active reporting, but
at least the Intel JHL6240 Thunderbolt 3 Bridge [8086:15c0] and the Intel
JHL7540 Thunderbolt 3 Bridge [8086:15ea] do not.

Previously we tried to wait for Link training to complete, but since there
was no DLL Link Active reporting, all we could do was wait the worst-case
1000 ms, then another 100 ms.

Instead of using the supported speeds to determine whether to wait for Link
training, check whether the port supports DLL Link Active reporting.  The
Ports in question do not, so we'll wait only the 100 ms required for Ports
that support Link speeds <= 5 GT/s.

This of course assumes these Ports always train the Link within 100 ms even
if they are operating at > 5 GT/s, which is not required by the spec.

[bhelgaas: commit log, comment]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206837
Link: https://lore.kernel.org/r/20200514133043.27429-1-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/pci.c | 30 +++++++++++++++++++++---------
 1 file changed, 21 insertions(+), 9 deletions(-)

diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index c73e8095a849..689f0280c038 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -4608,7 +4608,8 @@ static int pci_pm_reset(struct pci_dev *dev, int probe)
  * pcie_wait_for_link_delay - Wait until link is active or inactive
  * @pdev: Bridge device
  * @active: waiting for active or inactive?
- * @delay: Delay to wait after link has become active (in ms)
+ * @delay: Delay to wait after link has become active (in ms). Specify %0
+ *	   for no delay.
  *
  * Use this to wait till link becomes active or inactive.
  */
@@ -4649,7 +4650,7 @@ static bool pcie_wait_for_link_delay(struct pci_dev *pdev, bool active,
 		msleep(10);
 		timeout -= 10;
 	}
-	if (active && ret)
+	if (active && ret && delay)
 		msleep(delay);
 	else if (ret != active)
 		pci_info(pdev, "Data Link Layer Link Active not %s in 1000 msec\n",
@@ -4770,17 +4771,28 @@ void pci_bridge_wait_for_secondary_bus(struct pci_dev *dev)
 	if (!pcie_downstream_port(dev))
 		return;
 
-	if (pcie_get_speed_cap(dev) <= PCIE_SPEED_5_0GT) {
-		pci_dbg(dev, "waiting %d ms for downstream link\n", delay);
-		msleep(delay);
-	} else {
-		pci_dbg(dev, "waiting %d ms for downstream link, after activation\n",
-			delay);
-		if (!pcie_wait_for_link_delay(dev, true, delay)) {
+	/*
+	 * Per PCIe r5.0, sec 6.6.1, for downstream ports that support
+	 * speeds > 5 GT/s, we must wait for link training to complete
+	 * before the mandatory delay.
+	 *
+	 * We can only tell when link training completes via DLL Link
+	 * Active, which is required for downstream ports that support
+	 * speeds > 5 GT/s (sec 7.5.3.6).  Unfortunately some common
+	 * devices do not implement Link Active reporting even when it's
+	 * required, so we'll check for that directly instead of checking
+	 * the supported link speed.  We assume devices without Link Active
+	 * reporting can train in 100 ms regardless of speed.
+	 */
+	if (dev->link_active_reporting) {
+		pci_dbg(dev, "waiting for link to train\n");
+		if (!pcie_wait_for_link_delay(dev, true, 0)) {
 			/* Did not train, no need to wait any further */
 			return;
 		}
 	}
+	pci_dbg(child, "waiting %d ms to become accessible\n", delay);
+	msleep(delay);
 
 	if (!pci_device_is_present(child)) {
 		pci_dbg(child, "waiting additional %d ms to become accessible\n", delay);
-- 
2.25.1

[PATCH AUTOSEL 5.4 173/266] PCI/PTM: Inherit Switch Downstream Port PTM settings from Upstream Port

[Sasha Levin]

From: Bjorn Helgaas <bhelgaas@google.com>

[ Upstream commit 7b38fd9760f51cc83d80eed2cfbde8b5ead9e93a ]

Except for Endpoints, we enable PTM at enumeration-time.  Previously we did
not account for the fact that Switch Downstream Ports are not permitted to
have a PTM capability; their PTM behavior is controlled by the Upstream
Port (PCIe r5.0, sec 7.9.16).  Since Downstream Ports don't have a PTM
capability, we did not mark them as "ptm_enabled", which meant that
pci_enable_ptm() on an Endpoint failed because there was no PTM path to it.

Mark Downstream Ports as "ptm_enabled" if their Upstream Port has PTM
enabled.

Fixes: eec097d43100 ("PCI: Add pci_enable_ptm() for drivers to enable PTM on endpoints")
Reported-by: Aditya Paluri <Venkata.AdityaPaluri@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/pcie/ptm.c | 22 +++++++++++++++++-----
 1 file changed, 17 insertions(+), 5 deletions(-)

diff --git a/drivers/pci/pcie/ptm.c b/drivers/pci/pcie/ptm.c
index 9361f3aa26ab..357a454cafa0 100644
--- a/drivers/pci/pcie/ptm.c
+++ b/drivers/pci/pcie/ptm.c
@@ -39,10 +39,6 @@ void pci_ptm_init(struct pci_dev *dev)
 	if (!pci_is_pcie(dev))
 		return;
 
-	pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_PTM);
-	if (!pos)
-		return;
-
 	/*
 	 * Enable PTM only on interior devices (root ports, switch ports,
 	 * etc.) on the assumption that it causes no link traffic until an
@@ -52,6 +48,23 @@ void pci_ptm_init(struct pci_dev *dev)
 	     pci_pcie_type(dev) == PCI_EXP_TYPE_RC_END))
 		return;
 
+	/*
+	 * Switch Downstream Ports are not permitted to have a PTM
+	 * capability; their PTM behavior is controlled by the Upstream
+	 * Port (PCIe r5.0, sec 7.9.16).
+	 */
+	ups = pci_upstream_bridge(dev);
+	if (pci_pcie_type(dev) == PCI_EXP_TYPE_DOWNSTREAM &&
+	    ups && ups->ptm_enabled) {
+		dev->ptm_granularity = ups->ptm_granularity;
+		dev->ptm_enabled = 1;
+		return;
+	}
+
+	pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_PTM);
+	if (!pos)
+		return;
+
 	pci_read_config_dword(dev, pos + PCI_PTM_CAP, &cap);
 	local_clock = (cap & PCI_PTM_GRANULARITY_MASK) >> 8;
 
@@ -61,7 +74,6 @@ void pci_ptm_init(struct pci_dev *dev)
 	 * the spec recommendation (PCIe r3.1, sec 7.32.3), select the
 	 * furthest upstream Time Source as the PTM Root.
 	 */
-	ups = pci_upstream_bridge(dev);
 	if (ups && ups->ptm_enabled) {
 		ctrl = PCI_PTM_CTRL_ENABLE;
 		if (ups->ptm_granularity == 0)
-- 
2.25.1

[PATCH AUTOSEL 5.4 174/266] PCI: dwc: Fix inner MSI IRQ domain registration

[Sasha Levin]

From: Marc Zyngier <maz@kernel.org>

[ Upstream commit 0414b93e78d87ecc24ae1a7e61fe97deb29fa2f4 ]

On a system that uses the internal DWC MSI widget, I get this
warning from debugfs when CONFIG_GENERIC_IRQ_DEBUGFS is selected:

  debugfs: File ':soc:pcie@fc000000' in directory 'domains' already present!

This is due to the fact that the DWC MSI code tries to register two
IRQ domains for the same firmware node, without telling the low
level code how to distinguish them (by setting a bus token). This
further confuses debugfs which tries to create corresponding
files for each domain.

Fix it by tagging the inner domain as DOMAIN_BUS_NEXUS, which is
the closest thing we have as to "generic MSI".

Link: https://lore.kernel.org/r/20200501113921.366597-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/dwc/pcie-designware-host.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
index 8615f1548882..fbcb211cceb4 100644
--- a/drivers/pci/controller/dwc/pcie-designware-host.c
+++ b/drivers/pci/controller/dwc/pcie-designware-host.c
@@ -263,6 +263,8 @@ int dw_pcie_allocate_domains(struct pcie_port *pp)
 		return -ENOMEM;
 	}
 
+	irq_domain_update_bus_token(pp->irq_domain, DOMAIN_BUS_NEXUS);
+
 	pp->msi_domain = pci_msi_create_irq_domain(fwnode,
 						   &dw_pcie_msi_domain_info,
 						   pp->irq_domain);
-- 
2.25.1

[PATCH AUTOSEL 5.4 175/266] PCI: amlogic: meson: Don't use FAST_LINK_MODE to set up link

[Sasha Levin]

From: Marc Zyngier <maz@kernel.org>

[ Upstream commit 87dccf09323fc363bd0d072fcc12b96622ab8c69 ]

The vim3l board does not work with a standard PCIe switch (ASM1184e),
spitting all kind of errors - hinting at HW misconfiguration (no link,
port enumeration issues, etc).

According to the the Synopsys DWC PCIe Reference Manual, in the section
dedicated to the PLCR register, bit 7 is described (FAST_LINK_MODE) as:

"Sets all internal timers to fast mode for simulation purposes."

it is sound to set this bit from a simulation perspective, but on actual
silicon, which expects timers to have a nominal value, it is not.

Make sure the FAST_LINK_MODE bit is cleared when configuring the RC
to solve this problem.

Link: https://lore.kernel.org/r/20200429164230.309922-1-maz@kernel.org
Fixes: 9c0ef6d34fdb ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/dwc/pci-meson.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-meson.c b/drivers/pci/controller/dwc/pci-meson.c
index b927a92e3463..8c9f88704874 100644
--- a/drivers/pci/controller/dwc/pci-meson.c
+++ b/drivers/pci/controller/dwc/pci-meson.c
@@ -301,11 +301,11 @@ static void meson_pcie_init_dw(struct meson_pcie *mp)
 	meson_cfg_writel(mp, val, PCIE_CFG0);
 
 	val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF);
-	val &= ~LINK_CAPABLE_MASK;
+	val &= ~(LINK_CAPABLE_MASK | FAST_LINK_MODE);
 	meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF);
 
 	val = meson_elb_readl(mp, PCIE_PORT_LINK_CTRL_OFF);
-	val |= LINK_CAPABLE_X1 | FAST_LINK_MODE;
+	val |= LINK_CAPABLE_X1;
 	meson_elb_writel(mp, val, PCIE_PORT_LINK_CTRL_OFF);
 
 	val = meson_elb_readl(mp, PCIE_GEN2_CTRL_OFF);
-- 
2.25.1

[PATCH AUTOSEL 5.4 203/266] PCI: Avoid FLR for AMD Matisse HD Audio & USB 3.0

[Sasha Levin]

From: Marcos Scriven <marcos@scriven.org>

[ Upstream commit 0d14f06cd6657ba3446a5eb780672da487b068e7 ]

The AMD Matisse HD Audio & USB 3.0 devices advertise Function Level Reset
support, but hang when an FLR is triggered.

To reproduce the problem, attach the device to a VM, then detach and try to
attach again.

Rename the existing quirk_intel_no_flr(), which was not Intel-specific, to
quirk_no_flr(), and apply it to prevent the use of FLR on these AMD
devices.

Link: https://lore.kernel.org/r/CAAri2DpkcuQZYbT6XsALhx2e6vRqPHwtbjHYeiH7MNp4zmt1RA@mail.gmail.com
Signed-off-by: Marcos Scriven <marcos@scriven.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/quirks.c | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)

diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 798e52051ecc..3f89ba7fe7fb 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -5130,13 +5130,23 @@ static void quirk_intel_qat_vf_cap(struct pci_dev *pdev)
 }
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x443, quirk_intel_qat_vf_cap);
 
-/* FLR may cause some 82579 devices to hang */
-static void quirk_intel_no_flr(struct pci_dev *dev)
+/*
+ * FLR may cause the following to devices to hang:
+ *
+ * AMD Starship/Matisse HD Audio Controller 0x1487
+ * AMD Matisse USB 3.0 Host Controller 0x149c
+ * Intel 82579LM Gigabit Ethernet Controller 0x1502
+ * Intel 82579V Gigabit Ethernet Controller 0x1503
+ *
+ */
+static void quirk_no_flr(struct pci_dev *dev)
 {
 	dev->dev_flags |= PCI_DEV_FLAGS_NO_FLR_RESET;
 }
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1502, quirk_intel_no_flr);
-DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1503, quirk_intel_no_flr);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x1487, quirk_no_flr);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x149c, quirk_no_flr);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1502, quirk_no_flr);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1503, quirk_no_flr);
 
 static void quirk_no_ext_tags(struct pci_dev *pdev)
 {
-- 
2.25.1

[PATCH AUTOSEL 5.4 204/266] PCI: Avoid FLR for AMD Starship USB 3.0

[Sasha Levin]

From: Kevin Buettner <kevinb@redhat.com>

[ Upstream commit 5727043c73fdfe04597971b5f3f4850d879c1f4f ]

The AMD Starship USB 3.0 host controller advertises Function Level Reset
support, but it apparently doesn't work.  Add a quirk to prevent use of FLR
on this device.

Without this quirk, when attempting to assign (pass through) an AMD
Starship USB 3.0 host controller to a guest OS, the system becomes
increasingly unresponsive over the course of several minutes, eventually
requiring a hard reset.  Shortly after attempting to start the guest, I see
these messages:

  vfio-pci 0000:05:00.3: not ready 1023ms after FLR; waiting
  vfio-pci 0000:05:00.3: not ready 2047ms after FLR; waiting
  vfio-pci 0000:05:00.3: not ready 4095ms after FLR; waiting
  vfio-pci 0000:05:00.3: not ready 8191ms after FLR; waiting

And then eventually:

  vfio-pci 0000:05:00.3: not ready 65535ms after FLR; giving up
  INFO: NMI handler (perf_event_nmi_handler) took too long to run: 0.000 msecs
  perf: interrupt took too long (642744 > 2500), lowering kernel.perf_event_max_sample_rate to 1000
  INFO: NMI handler (perf_event_nmi_handler) took too long to run: 82.270 msecs
  INFO: NMI handler (perf_event_nmi_handler) took too long to run: 680.608 msecs
  INFO: NMI handler (perf_event_nmi_handler) took too long to run: 100.952 msecs
  ...
  watchdog: BUG: soft lockup - CPU#3 stuck for 22s! [qemu-system-x86:7487]

Tested on a Micro-Star International Co., Ltd. MS-7C59/Creator TRX40
motherboard with an AMD Ryzen Threadripper 3970X.

Link: https://lore.kernel.org/r/20200524003529.598434ff@f31-4.lan
Signed-off-by: Kevin Buettner <kevinb@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/quirks.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 3f89ba7fe7fb..de999f636a5f 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -5134,6 +5134,7 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x443, quirk_intel_qat_vf_cap);
  * FLR may cause the following to devices to hang:
  *
  * AMD Starship/Matisse HD Audio Controller 0x1487
+ * AMD Starship USB 3.0 Host Controller 0x148c
  * AMD Matisse USB 3.0 Host Controller 0x149c
  * Intel 82579LM Gigabit Ethernet Controller 0x1502
  * Intel 82579V Gigabit Ethernet Controller 0x1503
@@ -5144,6 +5145,7 @@ static void quirk_no_flr(struct pci_dev *dev)
 	dev->dev_flags |= PCI_DEV_FLAGS_NO_FLR_RESET;
 }
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x1487, quirk_no_flr);
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x148c, quirk_no_flr);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_AMD, 0x149c, quirk_no_flr);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1502, quirk_no_flr);
 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1503, quirk_no_flr);
-- 
2.25.1