[PATCH AUTOSEL 6.8 09/24] PCI/PM: Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports

[PATCH AUTOSEL 6.8 09/24] PCI/PM: Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports

[Sasha Levin]

From: Mario Limonciello <mario.limonciello@amd.com>

[ Upstream commit 256df20c590bf0e4d63ac69330cf23faddac3e08 ]

Hewlett-Packard HP Pavilion 17 Notebook PC/1972 is an Intel Ivy Bridge
system with a muxless AMD Radeon dGPU.  Attempting to use the dGPU fails
with the following sequence:

  ACPI Error: Aborting method \AMD3._ON due to previous error (AE_AML_LOOP_TIMEOUT) (20230628/psparse-529)
  radeon 0000:01:00.0: not ready 1023ms after resume; waiting
  radeon 0000:01:00.0: not ready 2047ms after resume; waiting
  radeon 0000:01:00.0: not ready 4095ms after resume; waiting
  radeon 0000:01:00.0: not ready 8191ms after resume; waiting
  radeon 0000:01:00.0: not ready 16383ms after resume; waiting
  radeon 0000:01:00.0: not ready 32767ms after resume; waiting
  radeon 0000:01:00.0: not ready 65535ms after resume; giving up
  radeon 0000:01:00.0: Unable to change power state from D3cold to D0, device inaccessible

The issue is that the Root Port the dGPU is connected to can't handle the
transition from D3cold to D0 so the dGPU can't properly exit runtime PM.

The existing logic in pci_bridge_d3_possible() checks for systems that are
newer than 2015 to decide that D3 is safe.  This would nominally work for
an Ivy Bridge system (which was discontinued in 2015), but this system
appears to have continued to receive BIOS updates until 2017 and so this
existing logic doesn't appropriately capture it.

Add the system to bridge_d3_blacklist to prevent D3cold from being used.

Link: https://lore.kernel.org/r/20240307163709.323-1-mario.limonciello@amd.com
Reported-by: Eric Heintzmann <heintzmann.eric@free.fr>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3229
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Eric Heintzmann <heintzmann.eric@free.fr>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/pci.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index c3585229c12a2..9d5d08a420f1a 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -3102,6 +3102,18 @@ static const struct dmi_system_id bridge_d3_blacklist[] = {
 			DMI_MATCH(DMI_BOARD_VERSION, "Continental Z2"),
 		},
 	},
+	{
+		/*
+		 * Changing power state of root port dGPU is connected fails
+		 * https://gitlab.freedesktop.org/drm/amd/-/issues/3229
+		 */
+		.ident = "Hewlett-Packard HP Pavilion 17 Notebook PC/1972",
+		.matches = {
+			DMI_MATCH(DMI_BOARD_VENDOR, "Hewlett-Packard"),
+			DMI_MATCH(DMI_BOARD_NAME, "1972"),
+			DMI_MATCH(DMI_BOARD_VERSION, "95.33"),
+		},
+	},
 #endif
 	{ }
 };
-- 
2.43.0

[PATCH AUTOSEL 6.8 23/24] PCI: Do not wait for disconnected devices when resuming

[Sasha Levin]

From: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

[ Upstream commit 6613443ffc49d03e27f0404978f685c4eac43fba ]

On runtime resume, pci_dev_wait() is called:

  pci_pm_runtime_resume()
    pci_pm_bridge_power_up_actions()
      pci_bridge_wait_for_secondary_bus()
        pci_dev_wait()

While a device is runtime suspended along with its PCI hierarchy, the
device could get disconnected. In such case, the link will not come up no
matter how long pci_dev_wait() waits for it.

Besides the above mentioned case, there could be other ways to get the
device disconnected while pci_dev_wait() is waiting for the link to come
up.

Make pci_dev_wait() exit if the device is already disconnected to avoid
unnecessary delay.

The use cases of pci_dev_wait() boil down to two:

  1. Waiting for the device after reset
  2. pci_bridge_wait_for_secondary_bus()

The callers in both cases seem to benefit from propagating the
disconnection as error even if device disconnection would be more
analoguous to the case where there is no device in the first place which
return 0 from pci_dev_wait(). In the case 2, it results in unnecessary
marking of the devices disconnected again but that is just harmless extra
work.

Also make sure compiler does not become too clever with dev->error_state
and use READ_ONCE() to force a fetch for the up-to-date value.

Link: https://lore.kernel.org/r/20240208132322.4811-1-ilpo.jarvinen@linux.intel.com
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/pci.c   | 5 +++++
 include/linux/pci.h | 7 ++++++-
 2 files changed, 11 insertions(+), 1 deletion(-)

diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index 9d5d08a420f1a..0658b374d988c 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -1250,6 +1250,11 @@ static int pci_dev_wait(struct pci_dev *dev, char *reset_type, int timeout)
 	for (;;) {
 		u32 id;
 
+		if (pci_dev_is_disconnected(dev)) {
+			pci_dbg(dev, "disconnected; not waiting\n");
+			return -ENOTTY;
+		}
+
 		pci_read_config_dword(dev, PCI_COMMAND, &id);
 		if (!PCI_POSSIBLE_ERROR(id))
 			break;
diff --git a/include/linux/pci.h b/include/linux/pci.h
index 213109d3c601d..b692472616efb 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -2519,7 +2519,12 @@ static inline struct pci_dev *pcie_find_root_port(struct pci_dev *dev)
 
 static inline bool pci_dev_is_disconnected(const struct pci_dev *dev)
 {
-	return dev->error_state == pci_channel_io_perm_failure;
+	/*
+	 * error_state is set in pci_dev_set_io_state() using xchg/cmpxchg()
+	 * and read w/o common lock. READ_ONCE() ensures compiler cannot cache
+	 * the value (e.g. inside the loop in pci_dev_wait()).
+	 */
+	return READ_ONCE(dev->error_state) == pci_channel_io_perm_failure;
 }
 
 void pci_request_acs(void);
-- 
2.43.0