Linux PCI subsystem development
 help / color / mirror / Atom feed
From: Claudiu Beznea <claudiu.beznea@kernel.org>
To: lpieralisi@kernel.org, kwilczynski@kernel.org, mani@kernel.org,
	robh@kernel.org, bhelgaas@google.com, p.zabel@pengutronix.de,
	18255117159@163.com
Cc: claudiu.beznea@tuxon.dev, linux-pci@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
	Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>,
	Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Subject: [PATCH v5 9/9] PCI: rzg3s-host: Add bridge::reset_root_port()
Date: Fri,  2 Oct 2026 14:09:35 +0300	[thread overview]
Message-ID: <20261002110935.2004349-10-claudiu.beznea@kernel.org> (raw)
In-Reply-To: <20261002110935.2004349-1-claudiu.beznea@kernel.org>

From: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>

Add bridge::reset_root_port(). This allows, on some devices, performing
reads and writes to an NVMe endpoint after a link down/link up cycle
without failures.

The implementation of struct pci_host_bridge::reset_root_port() masks all
enabled interrupts and synchronizes them before resetting the controller
to prevent asynchronous events from interfering with the reset operation.

struct rzg3s_pcie_host::started boolean was added to keep track of the
controller state, since rzg3s_pcie_host_start() and rzg3s_pcie_host_stop()
are called from multiple paths: .reset_root_port(), .suspend_noirq() and
.resume_noirq(). The flag prevents double start/stop and breaking
reference counters for clocks and resets.

rzg3s_pcie_pm_notifier() disables the link event IRQ, and disable_irq()
waits for a running IRQ thread to complete. If that thread is handling a
link down event, it calls .reset_root_port(), which unmasks the link
interrupt before returning, undoing the mask. Therefore, mask the link
interrupt again after disable_irq() has returned.

Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
---

Changes in v5:
- lock around reads/writes on RZG3S_PCI_PINTRCVIE
- in rzg3s_pcie_host_reset_root_port() kept non-relaxed reads/writes
  on interrupt disable registers (even though the spin lock/unlock are around
  them) to emphasize the need for updates before the IRQs are synchronized and
  relaxed variants on interrupt enable path
- collected tags

Changes in v4:
- this patch is new and is a split from patch 7 of v3
- use a boolean to keep track of the controller start state; with this
  the state management code from patch 7 of v3 was dropped 

 drivers/pci/controller/pcie-rzg3s-host.c | 83 +++++++++++++++++++++++-
 1 file changed, 81 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/controller/pcie-rzg3s-host.c b/drivers/pci/controller/pcie-rzg3s-host.c
index 78e783928b9d..eea215818633 100644
--- a/drivers/pci/controller/pcie-rzg3s-host.c
+++ b/drivers/pci/controller/pcie-rzg3s-host.c
@@ -331,6 +331,7 @@ struct rzg3s_pcie_port {
  * @max_link_speed: maximum supported link speed
  * @controller_id: PCIe controller identifier, used for System Controller access
  * @link_rescan: The PCIe link rescan state
+ * @started: The PCIe controller state (started or not)
  * @num_lanes: The number of lanes
  */
 struct rzg3s_pcie_host {
@@ -351,6 +352,7 @@ struct rzg3s_pcie_host {
 	int max_link_speed;
 	enum rzg3s_pcie_controller_id controller_id;
 	bool link_rescan;
+	bool started;
 	u8 num_lanes;
 };
 
@@ -1115,6 +1117,11 @@ static void rzg3s_pcie_link_event(struct rzg3s_pcie_host *host)
 
 		dev_info(host->dev, "PCIe link down, removing devices\n");
 
+		for_each_pci_bridge(dev, bridge->bus) {
+			if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT)
+				pci_host_handle_link_down(dev);
+		}
+
 		pci_lock_rescan_remove();
 		list_for_each_entry_safe_reverse(dev, tmp, &bus->devices,
 						 bus_list)
@@ -1869,6 +1876,9 @@ static int rzg3s_pcie_host_stop(struct rzg3s_pcie_host *host)
 	struct rzg3s_sysc *sysc = host->sysc;
 	int ret;
 
+	if (!host->started)
+		return 0;
+
 	clk_disable_unprepare(port->refclk);
 
 	/* SoC-specific de-initialization */
@@ -1890,6 +1900,8 @@ static int rzg3s_pcie_host_stop(struct rzg3s_pcie_host *host)
 	if (ret)
 		goto power_resets_restore;
 
+	host->started = false;
+
 	return 0;
 
 	/* Restore the previous state if any error happens */
@@ -1905,12 +1917,15 @@ static int rzg3s_pcie_host_stop(struct rzg3s_pcie_host *host)
 	return ret;
 }
 
-static int rzg3s_pcie_host_start(struct rzg3s_pcie_host *host)
+static int rzg3s_pcie_host_start(struct rzg3s_pcie_host *host, bool set_started)
 {
 	const struct rzg3s_pcie_soc_data *data = host->data;
 	struct rzg3s_sysc *sysc = host->sysc;
 	int ret;
 
+	if (host->started)
+		return 0;
+
 	ret = rzg3s_sysc_config_func(sysc, RZG3S_SYSC_FUNC_ID_MODE, 1);
 	if (ret)
 		return ret;
@@ -1943,6 +1958,9 @@ static int rzg3s_pcie_host_start(struct rzg3s_pcie_host *host)
 	if (ret)
 		goto assert_power_resets;
 
+	if (set_started)
+		host->started = true;
+
 	return 0;
 
 	/*
@@ -1956,6 +1974,64 @@ static int rzg3s_pcie_host_start(struct rzg3s_pcie_host *host)
 	return ret;
 }
 
+static int rzg3s_pcie_host_reset_root_port(struct pci_host_bridge *bridge,
+					   struct pci_dev *pdev)
+{
+	struct rzg3s_pcie_host *host = pci_host_bridge_priv(bridge);
+	unsigned long flags;
+	u32 irqs;
+	int ret;
+
+	/* Mask link up/down interrupts. */
+	writel(0, host->axi + RZG3S_PCI_PEIE0);
+
+	/* Mask INTx and MSI interrupts. */
+	raw_spin_lock_irqsave(&host->hw_lock, flags);
+	irqs = readl(host->axi + RZG3S_PCI_PINTRCVIE);
+	writel(0, host->axi + RZG3S_PCI_PINTRCVIE);
+	raw_spin_unlock_irqrestore(&host->hw_lock, flags);
+
+	/*
+	 * Make sure the next operations are not disturbed by any pending
+	 * IRQs.
+	 */
+	if (IS_ENABLED(CONFIG_PCI_MSI))
+		synchronize_irq(host->msi.irq);
+	for (unsigned int i = 0; i < PCI_NUM_INTX; i++)
+		synchronize_irq(host->intx_irqs[i]);
+
+	ret = rzg3s_pcie_host_stop(host);
+	if (ret) {
+		dev_err(host->dev, "Failed to stop the host!\n");
+		goto unmask_irqs;
+	}
+
+	ret = rzg3s_pcie_host_start(host, false);
+	if (ret) {
+		dev_err(host->dev, "Failed to start the host!\n");
+
+		/*
+		 * Don't unmask IRQs. We are in a bad state here and we
+		 * can recover only through a suspend/resume cycle. Just
+		 * return and preserve the stop state.
+		 */
+		return ret;
+	}
+
+unmask_irqs:
+	/* Unmask INTx and MSI interrupts. */
+	raw_spin_lock_irqsave(&host->hw_lock, flags);
+	writel_relaxed(irqs, host->axi + RZG3S_PCI_PINTRCVIE);
+	raw_spin_unlock_irqrestore(&host->hw_lock, flags);
+
+	/* Unmask link up/down interrupts. */
+	writel_relaxed(RZG3S_PCI_PEIE0_DL_UPDOWN, host->axi + RZG3S_PCI_PEIE0);
+
+	host->started = true;
+
+	return ret;
+}
+
 static int rzg3s_pcie_get_controller_id(struct rzg3s_pcie_host *host)
 {
 	struct device_node *np = host->dev->of_node;
@@ -2036,6 +2112,7 @@ static int rzg3s_pcie_pm_notifier(struct notifier_block *nb,
 	case PM_SUSPEND_PREPARE:
 		/* Disable link up/down interrupts. */
 		disable_irq(host->event_irq);
+		writel_relaxed(0, host->axi + RZG3S_PCI_PEIE0);
 		break;
 
 	case PM_POST_SUSPEND:
@@ -2143,6 +2220,7 @@ static int rzg3s_pcie_probe(struct platform_device *pdev)
 	if (ret)
 		goto power_resets_assert;
 
+	host->started = true;
 	host->pm_nb.notifier_call = rzg3s_pcie_pm_notifier;
 	ret = register_pm_notifier(&host->pm_nb);
 	if (ret)
@@ -2151,6 +2229,7 @@ static int rzg3s_pcie_probe(struct platform_device *pdev)
 	bridge->sysdata = host;
 	bridge->ops = &rzg3s_pcie_root_ops;
 	bridge->child_ops = &rzg3s_pcie_child_ops;
+	bridge->reset_root_port = rzg3s_pcie_host_reset_root_port;
 	ret = pci_host_probe(bridge);
 	if (ret)
 		goto pm_notifier_unregister;
@@ -2201,7 +2280,7 @@ static int rzg3s_pcie_resume_noirq(struct device *dev)
 {
 	struct rzg3s_pcie_host *host = dev_get_drvdata(dev);
 
-	return rzg3s_pcie_host_start(host);
+	return rzg3s_pcie_host_start(host, true);
 }
 
 static const struct dev_pm_ops rzg3s_pcie_pm_ops = {
-- 
2.43.0


  parent reply	other threads:[~2026-10-02 11:10 UTC|newest]

Thread overview: 22+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-10-02 11:09 [PATCH v5 0/9] PCI: rzg3s-host: Add PCIe hotplug support Claudiu Beznea
2026-10-02 11:09 ` [PATCH v5 1/9] PCI: rzg3s-host: Follow hardware manual clock/reset initialization order Claudiu Beznea
2026-10-02 11:23   ` sashiko-bot
2026-10-02 11:09 ` [PATCH v5 2/9] PCI: rzg3s-host: Fix runtime PM handling in the NOIRQ suspend/resume phase Claudiu Beznea
2026-10-02 11:18   ` sashiko-bot
2026-10-02 11:09 ` [PATCH v5 3/9] PCI: rzg3s-host: Select PCI_HOST_COMMON Claudiu Beznea
2026-10-02 11:22   ` sashiko-bot
2026-10-05 13:50     ` Claudiu Beznea
2026-10-02 11:09 ` [PATCH v5 4/9] PCI: rzg3s-host: Drop nop instructions Claudiu Beznea
2026-10-02 11:17   ` sashiko-bot
2026-10-02 11:09 ` [PATCH v5 5/9] PCI: rzg3s-host: Move host configuration code together Claudiu Beznea
2026-10-02 11:20   ` sashiko-bot
2026-10-02 11:09 ` [PATCH v5 6/9] PCI: rzg3s-host: Move suspend/resume code into dedicated functions Claudiu Beznea
2026-10-02 11:17   ` sashiko-bot
2026-10-02 11:09 ` [PATCH v5 7/9] PCI: rzg3s-host: Move IRQ domain setup code Claudiu Beznea
2026-10-02 11:19   ` sashiko-bot
2026-10-02 11:09 ` [PATCH v5 8/9] PCI: rzg3s-host: Re-enumerate the bus on PCIe link-state changes Claudiu Beznea
2026-10-02 11:25   ` sashiko-bot
2026-10-05 13:50     ` Claudiu Beznea
2026-10-02 11:09 ` Claudiu Beznea [this message]
2026-10-02 11:25   ` [PATCH v5 9/9] PCI: rzg3s-host: Add bridge::reset_root_port() sashiko-bot
2026-10-05 14:55     ` Claudiu Beznea

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20261002110935.2004349-10-claudiu.beznea@kernel.org \
    --to=claudiu.beznea@kernel.org \
    --cc=18255117159@163.com \
    --cc=bhelgaas@google.com \
    --cc=claudiu.beznea.uj@bp.renesas.com \
    --cc=claudiu.beznea@tuxon.dev \
    --cc=kwilczynski@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=lpieralisi@kernel.org \
    --cc=mani@kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
    --cc=robh@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox