Re: ARMADA espressobin SATA drive detection failure

["Pali Rohár" <pali@kernel.org>]

On Saturday 13 August 2022 12:47:30 Shinichiro Kawasaki wrote:
> On Aug 13, 2022 / 14:01, Pali Rohár wrote:
> > On Saturday 13 August 2022 11:53:39 Shinichiro Kawasaki wrote:
> > > On Aug 13, 2022 / 11:32, Pali Rohár wrote:
> > > > On Saturday 13 August 2022 01:35:35 Shinichiro Kawasaki wrote:
> > > 
> > > [...]
> > > 
> > > > Ok, thanks for testing. It looks like that reset code has some issues.
> > > > 
> > > > Could you please test this change?
> > > > 
> > > > @@ -1393,7 +1436,8 @@ static int mvebu_a3700_comphy_probe(struct platform_device *pdev)
> > > >  		 * To avoid relying on the bootloader/firmware configuration,
> > > >  		 * power off all comphys.
> > > >  		 */
> > > > -		mvebu_a3700_comphy_reset(phy);
> > > > +//		mvebu_a3700_comphy_reset(phy);
> > > > +		mvebu_a3700_comphy_power_off(phy);
> > > >  		lane->needs_reset = false;
> > > >  	}
> > > >  
> > > > 
> > > > It should replace reset code by power off at beginning / probe time.
> > > 
> > > This change also avoided the "ata1: SATA link down (SStatus 0 SControl 300)"
> > > message, and my SSD was detected as /dev/sda. Good symptoms for me. FYI, I
> > > attach the console log with this change. (This time, following messages were
> > > printed. Not sure if they are important or not.)
> > > 
> > > [    2.937376] mvebu-a3700-comphy d0018300.phy: invalid COMPHY mode
> > > [    2.943581] mvebu-a3700-comphy d0018300.phy: invalid COMPHY mode
> > > [    2.949679] mvebu-a3700-comphy d0018300.phy: invalid COMPHY mode
> > 
> > Those errors are important, it means that power_off did nothing and was
> > skipped. So test did nothing.
> > 
> > Could you please replace mvebu_a3700_comphy_power_off implementation
> > with this one and try it again?
> > 
> > static int mvebu_a3700_comphy_power_off(struct phy *phy)
> > {
> > 	struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
> > 
> > 	switch (lane->id) {
> > 	case 0:
> > 		mvebu_a3700_comphy_usb3_power_off(lane);
> > 		mvebu_a3700_comphy_ethernet_power_off(lane);
> > 		return 0;
> > 	case 1:
> > 		mvebu_a3700_comphy_pcie_power_off(lane);
> > 		mvebu_a3700_comphy_ethernet_power_off(lane);
> > 		return 0;
> > 	case 2:
> > 		mvebu_a3700_comphy_usb3_power_off(lane);
> > 		mvebu_a3700_comphy_sata_power_off(lane);
> > 		return 0;
> > 	default:
> > 		dev_err(lane->dev, "invalid COMPHY mode\n");
> > 		return -EINVAL;
> > 	}
> > }
> 
> Thanks, but this hunk failed to compile with the error below.
> 
> rivers/phy/marvell/phy-mvebu-a3700-comphy.c: In function 'mvebu_a3700_comphy_power_off':
> drivers/phy/marvell/phy-mvebu-a3700-comphy.c:1229:17: error: implicit declaration of function 'mvebu_a3700_comphy_usb3_power_off'; did you mean 'mvebu_a3700_comphy_usb3_power_on'? [-Werror=implicit-function-declaration]
>  1229 |                 mvebu_a3700_comphy_usb3_power_off(lane);
>       |                 ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
>       |                 mvebu_a3700_comphy_usb3_power_on
> cc1: some warnings being treated as errors
> 
> Do I need to add mvebu_a3700_comphy_usb3_power_off() function?

In my original version of this driver I have:

static void mvebu_a3700_comphy_usb3_power_off(struct mvebu_a3700_comphy_lane *lane)
{
	/*
	 * Currently the USB3 MAC will control the USB3 PHY to set it to low
	 * state, thus do not need to power off USB3 PHY again.
	 */
}

So please remove mvebu_a3700_comphy_usb3_power_off() calls as it does
nothing.

> I suspend this work here today. Will resume it tomorrow. Thank you for your
> actions so far. Wish this issue gets resolved soon.
> 
> -- 
> Shin'ichiro Kawasaki

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy