[PATCH 4/7] dt-bindings: usb: ti,musb-am33xx: Convert to DT schema

[Bhargav Joshi <j.bhargav.u@gmail.com>]

Convert the TI AM33xx MUSB text bindings to DT schema.
Changes during conversion:
- Allow an optional vbus interrupt used in am335x-bone-common.
- Add the interface-type and phy-names properties natively used by the
  dm816x hardware.
- Allow 0 or 1 for mentor,multipoint. While the text binding mandated 1,
  the Mentor USB IP natively supports both single and multipoint
  configurations as used in existing DTS.

Signed-off-by: Bhargav Joshi <j.bhargav.u@gmail.com>
---
 .../devicetree/bindings/usb/am33xx-usb.txt         |  25 -----
 .../devicetree/bindings/usb/ti,musb-am33xx.yaml    | 111 +++++++++++++++++++++
 2 files changed, 111 insertions(+), 25 deletions(-)

diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
index 8832843c7d7c..5973f88bcc65 100644
--- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt
+++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt
@@ -17,31 +17,6 @@ Reset module
 - reg-names: "phy_ctrl" for the "USB control registers" and "wakeup" for
   the USB wake up control register.
 
-USB
-~~~
-- compatible: ti,musb-am33xx
-- reg: offset and length of "USB Controller Registers", and offset and
-  length of "USB Core" register space.
-- reg-names: control for the ""USB Controller Registers" and "mc" for
-  "USB Core" register space
-- interrupts: USB interrupt number
-- interrupt-names: mc
-- dr_mode: Should be one of "host", "peripheral" or "otg".
-- mentor,multipoint: Should be "1" indicating the musb controller supports
-  multipoint. This is a MUSB configuration-specific setting.
-- mentor,num-eps: Specifies the number of endpoints. This is also a
-  MUSB configuration-specific setting. Should be set to "16"
-- mentor,ram-bits: Specifies the ram address size. Should be set to "12"
-- mentor,power: Should be "500". This signifies the controller can supply up to
-  500mA when operating in host mode.
-- phys: reference to the USB phy
-- dmas: specifies the dma channels
-- dma-names: specifies the names of the channels. Use "rxN" for receive
-  and "txN" for transmit endpoints. N specifies the endpoint number.
-
-The controller should have an "usb" alias numbered properly in the alias
-node.
-
 Example:
 ~~~~~~~~
 The following example contains all the nodes as used on am335x-evm:
diff --git a/Documentation/devicetree/bindings/usb/ti,musb-am33xx.yaml b/Documentation/devicetree/bindings/usb/ti,musb-am33xx.yaml
new file mode 100644
index 000000000000..05909d5ca3d2
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/ti,musb-am33xx.yaml
@@ -0,0 +1,111 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/ti,musb-am33xx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI AM33xx/DM816 MUSB
+
+maintainers:
+  - Ravi B <ravibabu@ti.com>
+  - Ajay Kumar Gupta <ajay.gupta@ti.com>
+
+allOf:
+  - $ref: /schemas/usb/usb-drd.yaml#
+
+properties:
+  compatible:
+    enum:
+      - ti,musb-am33xx
+      - ti,musb-dm816
+
+  reg:
+    maxItems: 2
+
+  reg-names:
+    items:
+      - const: mc
+      - const: control
+
+  interrupts:
+    minItems: 1
+    maxItems: 2
+
+  interrupt-names:
+    minItems: 1
+    items:
+      - const: mc
+      - const: vbus
+
+  mentor,multipoint:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Indicates the musb controller supports multipoint.
+    enum: [0, 1]
+
+  mentor,num-eps:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Specifies the number of endpoints.
+    const: 16
+
+  mentor,ram-bits:
+    description: Specifies the ram address size.
+    const: 12
+
+  mentor,power:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Controller supply capacity (in mA) when operating in host mode.
+    const: 500
+
+  phys:
+    maxItems: 1
+
+  dmas:
+    minItems: 1
+    maxItems: 30
+
+  dma-names:
+    minItems: 1
+    maxItems: 30
+
+  phy-names:
+    const: usb2-phy
+
+  interface-type:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Describes the type of interface between the controller and the PHY.
+    enum: [ 0, 1 ]
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - interrupt-names
+  - dr_mode
+  - mentor,multipoint
+  - mentor,num-eps
+  - mentor,ram-bits
+  - mentor,power
+  - phys
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    usb@47401000 {
+        compatible = "ti,musb-am33xx";
+        reg = <0x47401400 0x400>,
+              <0x47401000 0x200>;
+        reg-names = "mc", "control";
+        interrupts = <18>;
+        interrupt-names = "mc";
+        dr_mode = "otg";
+        mentor,multipoint = <1>;
+        mentor,num-eps = <16>;
+        mentor,ram-bits = <12>;
+        mentor,power = <500>;
+        phys = <&usb0_phy>;
+        dmas = <&cppi41dma 0 0 &cppi41dma 1 0>;
+        dma-names = "rx1", "tx1";
+    };
+

-- 
2.55.0


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy