[PATCH v2 0/3] phy: qcom: Add USB PHY support for Nord SoC

[PATCH v2 0/3] phy: qcom: Add USB PHY support for Nord SoC

[Bartosz Golaszewski]

The series documents Nord in qcom,snps-eusb2-phy and
qcom,sc8280xp-qmp-usb43dp-phy bindings, updates qmp-combo PHY driver for
Nord SoC support.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
---
Changes in v2:
- Rephrase the commit message in patch 1/4: drop any mentions of the
  driver implementation as it has no impact on the bindings. Clarify
  that usb20 PHY really does not have an external reset.
- Squash patches 1 and 2 for the optional reset change to make sense in
  the context of adding the nord compatible.
- Fix tx_tbl register values for Nord.
- Link to v1: https://lore.kernel.org/all/20260901095055.42229-1-shengchao.guo@oss.qualcomm.com/

---
Bartosz Golaszewski (3):
      dt-bindings: phy: qcom,snps-eusb2-phy: Document the Nord eUSB2 PHY
      dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp-phy: Document the Nord QMP PHY
      phy: qcom: qmp-combo: Add USB3+DP PHY support for Nord

 .../phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml         |  2 +
 .../bindings/phy/qcom,snps-eusb2-phy.yaml          |  2 +-
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c          | 80 ++++++++++++++++++++++
 3 files changed, 83 insertions(+), 1 deletion(-)
---
base-commit: 0d9d0dbf2fddcff5859d623e90ca73c4054276e1
change-id: 20260914-nord-usb-phy-d6dd376b6b53

Best regards,
-- 
Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 1/3] dt-bindings: phy: qcom,snps-eusb2-phy: Document the Nord eUSB2 PHY

[Bartosz Golaszewski]

Add a compatible for the eUSB2 PHY found on the Qualcomm Nord SoC.
It is compatible with the sm8550 eUSB2 PHY.

While at it: On Nord SoC there are three eUSB2 PHYs but only two QUSB2PHY
block resets: the HS-only USB20 tile has no dedicated PHY reset and is
instead reset as a whole through the controller's own USB20_PRIM_BCR.

Make the 'resets' property optional.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
---
 Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml
index 096f6b546632ef8cb83321961c7e5ff261db2b1d..7fe8c82db38d876a9230697103dd9467c49f6c84 100644
--- a/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml
@@ -19,6 +19,7 @@ properties:
           - enum:
               - qcom,eliza-snps-eusb2-phy
               - qcom,milos-snps-eusb2-phy
+              - qcom,nord-snps-eusb2-phy
               - qcom,sar2130p-snps-eusb2-phy
               - qcom,sdx75-snps-eusb2-phy
               - qcom,sm8650-snps-eusb2-phy
@@ -64,7 +65,6 @@ required:
   - clock-names
   - vdd-supply
   - vdda12-supply
-  - resets
 
 additionalProperties: false
 

-- 
2.47.3


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 1/3] dt-bindings: phy: qcom,snps-eusb2-phy: Document the Nord eUSB2 PHY

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Low] dt-bindings: snps-eusb2-phy weakens validation by dropping required resets
--

commit 40f3e2fd7afd242254a8fb682a03903a7a5acc6d
Author: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>

dt-bindings: phy: qcom,snps-eusb2-phy: Document the Nord eUSB2 PHY

Add a compatible for the eUSB2 PHY found on the Qualcomm Nord SoC. This 
commit removes the resets property from the globally required list, as the 
Nord SoC does not have a dedicated PHY reset for the HS-only USB20 tile.

> diff --git a/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml
> index 096f6b546632e..7fe8c82db38d8 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml
[ ... ]
> @@ -64,7 +65,6 @@ required:
>    - clock-names
>    - vdd-supply
>    - vdda12-supply
> -  - resets

[Severity: Low]
Does removing resets from the globally required list weaken validation for
the existing SoCs?

If a device tree for older SoCs like sm8550 or sm8650 erroneously omits the
resets property, it appears it will now silently pass schema validation. 
Would it be better to add an allOf conditional block that keeps resets in
the required list for the older compatible strings that still mandate it?

>  additionalProperties: false

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260916-nord-usb-phy-v2-0-2c8461bb30e6@oss.qualcomm.com?part=1

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 1/3] dt-bindings: phy: qcom,snps-eusb2-phy: Document the Nord eUSB2 PHY

[Krzysztof Kozlowski]

On Wed, Sep 16, 2026 at 08:30:51PM +0200, Bartosz Golaszewski wrote:
> Add a compatible for the eUSB2 PHY found on the Qualcomm Nord SoC.
> It is compatible with the sm8550 eUSB2 PHY.
> 
> While at it: On Nord SoC there are three eUSB2 PHYs but only two QUSB2PHY
> block resets: the HS-only USB20 tile has no dedicated PHY reset and is
> instead reset as a whole through the controller's own USB20_PRIM_BCR.
> 
> Make the 'resets' property optional.

So this is a correct explanation for Nord, but you do much more than
explained here. You make it optional for Eliza, Milos and every other
device but use "Nord" as an argument. It's wrong argument. Eliza is
different than Nord. This either needs proper explanation or a fix - you
need constraints per variants (allOf:if:then).

Best regards,
Krzysztof


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 2/3] dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp-phy: Document the Nord QMP PHY

[Bartosz Golaszewski]

Add a compatible for the USB3+DP combo QMP PHY found on the Qualcomm Nord
SoC. The PHY sits behind a GDSC, so also allow (and require) power-domains
for it.

The block gets a standalone compatible rather than a fallback to an
existing one, because it is not register-compatible with any PHY already
described here. Its USB3 and DP initialisation sequences do match sm8550,
but Nord places the sub-blocks at different offsets within the PHY: it
exposes a dedicated USB3_PCS_AON region at 0x1e00, which sm8550 does not
have at all. Falling back to sm8550 - or to any other entry - would make
the driver program the wrong addresses.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Assisted-by: LLM
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
---
 .../devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml          | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
index 43e90995709f97c6c0af093e6b76367f419d41b9..13e64fe510b8f4218bc11e1c92e87ab3b02d5ba8 100644
--- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml
@@ -31,6 +31,7 @@ properties:
       - enum:
           - qcom,glymur-qmp-usb3-dp-phy
           - qcom,hawi-qmp-usb3-dp-phy
+          - qcom,nord-qmp-usb3-dp-phy
           - qcom,sar2130p-qmp-usb3-dp-phy
           - qcom,sc7180-qmp-usb3-dp-phy
           - qcom,sc7280-qmp-usb3-dp-phy
@@ -249,6 +250,7 @@ allOf:
             enum:
               - qcom,glymur-qmp-usb3-dp-phy
               - qcom,hawi-qmp-usb3-dp-phy
+              - qcom,nord-qmp-usb3-dp-phy
               - qcom,sar2130p-qmp-usb3-dp-phy
               - qcom,sc8280xp-qmp-usb43dp-phy
               - qcom,sm6350-qmp-usb3-dp-phy

-- 
2.47.3


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 3/3] phy: qcom: qmp-combo: Add USB3+DP PHY support for Nord

[Bartosz Golaszewski]

Nord SoC provides two USB3+DP combo PHYs. Their initialisation sequences
are identical to sm8550, but the sub-blocks are not laid out the same way:
Nord adds a dedicated USB3_PCS_AON region at offset 0x1e00 and leaves
everything else where sm8550 has it. None of the existing offsets tables
describe that, so add a v6 table which is the v3 layout plus usb3_pcs_aon.

Populating usb3_pcs_aon changes where the driver drives the I/O clamp when
entering and leaving autonomous mode: it now uses the real AON region
rather than falling back to PCS_MISC, which is what platforms with no AON
region do.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Assisted-by: LLM
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Signed-off-by: Shawn Guo <shengchao.guo@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 80 +++++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index a4f130fc33e3990e4101a710803bb4d0a0ed077b..c4e88b0384cb557f88f5af233f0568c7a93ab9cd 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -2356,6 +2356,20 @@ static const struct qmp_phy_init_tbl hawi_usb3_pcs_usb_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_V10_PCS_USB3_RCVR_DTCT_DLY_U3_H, 0x00),
 };
 
+static const struct qmp_phy_init_tbl nord_usb3_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_TX, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_RX, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_RX, 0x09),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_1, 0xf5),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_3, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_4, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_5, 0x5f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RCV_DETECT_LVL_2, 0x14),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V6_TX_PI_QEC_CTRL, 0x21, 1),
+	QMP_PHY_INIT_CFG_LANE(QSERDES_V6_TX_PI_QEC_CTRL, 0x05, 2),
+};
+
 /* list of regulators */
 static struct regulator_bulk_data qmp_phy_vreg_l[] = {
 	{ .supply = "vdda-phy", .init_load_uA = 21800, },
@@ -2720,6 +2734,23 @@ static const struct qmp_combo_offsets qmp_combo_offsets_v5 = {
 	.dp_dp_phy	= 0x2200,
 };
 
+static const struct qmp_combo_offsets qmp_combo_offsets_v6 = {
+	.com		= 0x0000,
+	.txa		= 0x1200,
+	.rxa		= 0x1400,
+	.txb		= 0x1600,
+	.rxb		= 0x1800,
+	.usb3_serdes	= 0x1000,
+	.usb3_pcs_misc	= 0x1a00,
+	.usb3_pcs	= 0x1c00,
+	.usb3_pcs_aon	= 0x1e00,
+	.usb3_pcs_usb	= 0x1f00,
+	.dp_serdes	= 0x2000,
+	.dp_txa		= 0x2200,
+	.dp_txb		= 0x2600,
+	.dp_dp_phy	= 0x2a00,
+};
+
 static const struct qmp_combo_offsets qmp_combo_offsets_v8 = {
 	.com		= 0x0000,
 	.txa		= 0x1400,
@@ -3424,6 +3455,51 @@ static const struct qmp_phy_cfg glymur_usb3dpphy_cfg = {
 	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_refgen),
 };
 
+static const struct qmp_phy_cfg nord_usb3dpphy_cfg = {
+	.offsets		= &qmp_combo_offsets_v6,
+
+	.serdes_tbl		= sm8550_usb3_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8550_usb3_serdes_tbl),
+	.tx_tbl			= nord_usb3_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(nord_usb3_tx_tbl),
+	.rx_tbl			= sm8550_usb3_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8550_usb3_rx_tbl),
+	.pcs_tbl		= sm8550_usb3_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8550_usb3_pcs_tbl),
+	.pcs_usb_tbl		= sm8550_usb3_pcs_usb_tbl,
+	.pcs_usb_tbl_num	= ARRAY_SIZE(sm8550_usb3_pcs_usb_tbl),
+
+	.dp_serdes_tbl		= qmp_v6_dp_serdes_tbl,
+	.dp_serdes_tbl_num	= ARRAY_SIZE(qmp_v6_dp_serdes_tbl),
+	.dp_tx_tbl		= qmp_v6_dp_tx_tbl,
+	.dp_tx_tbl_num		= ARRAY_SIZE(qmp_v6_dp_tx_tbl),
+
+	.serdes_tbl_rbr		= qmp_v6_dp_serdes_tbl_rbr,
+	.serdes_tbl_rbr_num	= ARRAY_SIZE(qmp_v6_dp_serdes_tbl_rbr),
+	.serdes_tbl_hbr		= qmp_v6_dp_serdes_tbl_hbr,
+	.serdes_tbl_hbr_num	= ARRAY_SIZE(qmp_v6_dp_serdes_tbl_hbr),
+	.serdes_tbl_hbr2	= qmp_v6_dp_serdes_tbl_hbr2,
+	.serdes_tbl_hbr2_num	= ARRAY_SIZE(qmp_v6_dp_serdes_tbl_hbr2),
+	.serdes_tbl_hbr3	= qmp_v6_dp_serdes_tbl_hbr3,
+	.serdes_tbl_hbr3_num	= ARRAY_SIZE(qmp_v6_dp_serdes_tbl_hbr3),
+
+	.swing_hbr_rbr		= &qmp_dp_v5_voltage_swing_hbr_rbr,
+	.pre_emphasis_hbr_rbr	= &qmp_dp_v6_pre_emphasis_hbr_rbr,
+	.swing_hbr3_hbr2	= &qmp_dp_v5_voltage_swing_hbr3_hbr2,
+	.pre_emphasis_hbr3_hbr2	= &qmp_dp_v5_pre_emphasis_hbr3_hbr2,
+
+	.dp_aux_init		= qmp_v4_dp_aux_init,
+	.configure_dp_tx	= qmp_v4_configure_dp_tx,
+	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
+	.configure_dp_phy	= qmp_v4_configure_dp_phy,
+
+	.regs			= qmp_v6_usb3phy_regs_layout,
+	.reset_list		= msm8996_usb3phy_reset_l,
+	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+};
+
 static int qmp_combo_dp_serdes_init(struct qmp_combo *qmp)
 {
 	const struct qmp_phy_cfg *cfg = qmp->cfg;
@@ -5621,6 +5697,10 @@ static const struct of_device_id qmp_combo_of_match_table[] = {
 		.compatible = "qcom,hawi-qmp-usb3-dp-phy",
 		.data = &hawi_usb3dpphy_cfg,
 	},
+	{
+		.compatible = "qcom,nord-qmp-usb3-dp-phy",
+		.data = &nord_usb3dpphy_cfg,
+	},
 	{
 		.compatible = "qcom,sar2130p-qmp-usb3-dp-phy",
 		.data = &sar2130p_usb3dpphy_cfg,

-- 
2.47.3


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 3/3] phy: qcom: qmp-combo: Add USB3+DP PHY support for Nord

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] phy: qcom: mismatch between commit message and nord_usb3_tx_tbl
--

commit 1b7c23f467a9a0ffe85f80b15fdee3ce3ad5c895
Author: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>

phy: qcom: qmp-combo: Add USB3+DP PHY support for Nord

Nord SoC provides two USB3+DP combo PHYs. Their initialisation sequences
are identical to sm8550, but the sub-blocks are not laid out the same way.
A dedicated USB3_PCS_AON region at offset 0x1e00 is added, modifying how
the I/O clamp is driven.

> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> index a4f130fc33e39..c4e88b0384cb5 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> @@ -2356,6 +2356,20 @@ static const struct qmp_phy_init_tbl hawi_usb3_pcs_usb_tbl[] = {
>  	QMP_PHY_INIT_CFG(QPHY_V10_PCS_USB3_RCVR_DTCT_DLY_U3_H, 0x00),
>  };
>  
> +static const struct qmp_phy_init_tbl nord_usb3_tx_tbl[] = {
> +	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_TX, 0x00),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_RX, 0x00),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_TX, 0x1f),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RES_CODE_LANE_OFFSET_RX, 0x09),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_1, 0xf5),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_3, 0x3f),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_4, 0x3f),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_TX_LANE_MODE_5, 0x5f),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_TX_RCV_DETECT_LVL_2, 0x14),

[Severity: Medium]
The commit message claims that the initialization sequences are identical to
sm8550. However, this configures QSERDES_V6_TX_RCV_DETECT_LVL_2 to 0x14,
whereas sm8550 uses 0x12.

Is this an intentional hardware difference for Nord that should be mentioned
in the commit message, or is it an accidental typo?

> +	QMP_PHY_INIT_CFG_LANE(QSERDES_V6_TX_PI_QEC_CTRL, 0x21, 1),
> +	QMP_PHY_INIT_CFG_LANE(QSERDES_V6_TX_PI_QEC_CTRL, 0x05, 2),
> +};

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260916-nord-usb-phy-v2-0-2c8461bb30e6@oss.qualcomm.com?part=3

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy