[PATCH v4 1/6] dt-bindings: phy: qcom,qmp-usb: Add IPQ9650 USB3 PHY

[PATCH v4 1/6] dt-bindings: phy: qcom,qmp-usb: Add IPQ9650 USB3 PHY

[Varadarajan Narayanan]

Document the Qualcomm IPQ9650 USB3 QMP PHY compatible.

Use a standalone compatible because the IPQ9650 PHY has register
configuration data that differs from the currently supported SoCs and
should not fall back to an existing definition.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
---
 .../devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml         | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml
index 01342823e57f..746c5a331f48 100644
--- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml
@@ -23,6 +23,7 @@ properties:
               - qcom,ipq6018-qmp-usb3-phy
               - qcom,ipq8074-qmp-usb3-phy
               - qcom,ipq9574-qmp-usb3-phy
+              - qcom,ipq9650-qmp-usb3-phy
               - qcom,msm8996-qmp-usb3-phy
               - qcom,qcs8300-qmp-usb3-uni-phy
               - qcom,qdu1000-qmp-usb3-uni-phy
@@ -102,6 +103,7 @@ allOf:
               - qcom,ipq6018-qmp-usb3-phy
               - qcom,ipq8074-qmp-usb3-phy
               - qcom,ipq9574-qmp-usb3-phy
+              - qcom,ipq9650-qmp-usb3-phy
               - qcom,msm8996-qmp-usb3-phy
               - qcom,sdx55-qmp-usb3-uni-phy
               - qcom,sdx65-qmp-usb3-uni-phy

-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v4 3/6] phy: qcom: qmp-usb: Add IPQ9650 USB3 PHY configuration

[Varadarajan Narayanan]

Add the USB3 QMP PHY configuration for IPQ9650, including the SoC-specific
init tables and compatible data.

IPQ9650 uses settings that do not match any existing supported SoC, so add
a dedicated configuration to allow the driver to support it.

Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 118 ++++++++++++++++++++++++++++++++
 1 file changed, 118 insertions(+)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-usb.c b/drivers/phy/qualcomm/phy-qcom-qmp-usb.c
index b0790bcf0bc8..e772e1fa27cf 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-usb.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-usb.c
@@ -400,6 +400,101 @@ static const struct qmp_phy_init_tbl ipq8074_usb3_pcs_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0f),
 };
 
+static const struct qmp_phy_init_tbl ipq9650_usb3_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_IVCO, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER1, 0x7d),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_BUF_ENABLE, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CMN_IPTRIM, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BG_TIMER, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP_EN, 0x42),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE0, 0xd4),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE0, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE0, 0x68),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE0, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE_MAP, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE0, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE2_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0xa2),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_HSCLK_SEL, 0x01),
+};
+
+static const struct qmp_phy_init_tbl ipq9650_usb3_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xb5),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_2, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x00),
+};
+
+static const struct qmp_phy_init_tbl ipq9650_usb3_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xe4),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0x64),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0xf6),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x89),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0x35),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+};
+
+static const struct qmp_phy_init_tbl ipq9650_usb3_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RATE_SLEW_CNTRL1, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xaa),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_FLL_CNTRL2, 0x83),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_FLL_CNTRL1, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_FLL_CNT_VAL_L, 0x09),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_FLL_MAN_CODE, 0x40),
+};
+
+static const struct qmp_phy_init_tbl ipq9650_usb3_pcs_usb_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_LFPS_DET_HIGH_COUNT_VAL, 0xf8),
+};
+
 static const struct qmp_phy_init_tbl msm8996_usb3_serdes_tbl[] = {
 	QMP_PHY_INIT_CFG(QSERDES_V2_COM_SYSCLK_EN_SEL, 0x14),
 	QMP_PHY_INIT_CFG(QSERDES_V2_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
@@ -1596,6 +1691,26 @@ static const struct qmp_phy_cfg ipq9574_usb3phy_cfg = {
 	.regs			= qmp_v3_usb3phy_regs_layout,
 };
 
+static const struct qmp_phy_cfg ipq9650_usb3phy_cfg = {
+	.offsets		= &qmp_usb_offsets_v4,
+
+	.serdes_tbl		= ipq9650_usb3_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(ipq9650_usb3_serdes_tbl),
+	.tx_tbl			= ipq9650_usb3_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(ipq9650_usb3_tx_tbl),
+	.rx_tbl			= ipq9650_usb3_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(ipq9650_usb3_rx_tbl),
+	.pcs_tbl		= ipq9650_usb3_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(ipq9650_usb3_pcs_tbl),
+	.pcs_usb_tbl		= ipq9650_usb3_pcs_usb_tbl,
+	.pcs_usb_tbl_num	= ARRAY_SIZE(ipq9650_usb3_pcs_usb_tbl),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= qmp_v4_usb3phy_regs_layout,
+
+	.has_pwrdn_delay	= true,
+};
+
 static const struct qmp_phy_cfg msm8996_usb3phy_cfg = {
 	.offsets		= &qmp_usb_offsets_v3_msm8996,
 
@@ -2483,6 +2598,9 @@ static const struct of_device_id qmp_usb_of_match_table[] = {
 	}, {
 		.compatible = "qcom,ipq9574-qmp-usb3-phy",
 		.data = &ipq9574_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,ipq9650-qmp-usb3-phy",
+		.data = &ipq9650_usb3phy_cfg,
 	}, {
 		.compatible = "qcom,msm8996-qmp-usb3-phy",
 		.data = &msm8996_usb3phy_cfg,

-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v4 3/6] phy: qcom: qmp-usb: Add IPQ9650 USB3 PHY configuration

[Dmitry Baryshkov]

On Mon, Oct 05, 2026 at 12:06:28PM +0530, Varadarajan Narayanan wrote:
> Add the USB3 QMP PHY configuration for IPQ9650, including the SoC-specific
> init tables and compatible data.
> 
> IPQ9650 uses settings that do not match any existing supported SoC, so add
> a dedicated configuration to allow the driver to support it.
> 
> Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
> Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
> ---
>  drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 118 ++++++++++++++++++++++++++++++++
>  1 file changed, 118 insertions(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v4 5/6] phy: qcom: snps-femto-v2: Move PHY init registers to config tables

[Varadarajan Narayanan]

The driver currently programs the common PHY register sequence directly in
qcom_snps_hsphy_init(), with the fixed register writes split around the
override parameter handling. This makes it hard to support SoCs that need a
different sequence or different values.

Move the fixed pre- and post-override register programming into per-
compatible configuration tables, and keep the 7 nm override parameters in
the same match-data structure. This allows the driver to share the common
sequence while adding SoC-specific sequences for future platforms such as
IPQ9650.

Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 124 ++++++++++++++++----------
 1 file changed, 78 insertions(+), 46 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
index 0ead37c0dcfd..b6bbf2b570c7 100644
--- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
+++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
@@ -104,6 +104,20 @@ struct phy_override_seq {
 	u8	mask;
 };
 
+struct phy_reg_config {
+	u32 offset;
+	u32 mask;
+	u32 val;
+};
+
+struct phy_config_data {
+	const struct phy_reg_config *pre_tuning;
+	const struct override_param_map *override;
+	const struct phy_reg_config *post_tuning;
+	const u32 num_pre_tuning;
+	const u32 num_post_tuning;
+};
+
 #define NUM_HSPHY_TUNING_PARAMS	(9)
 
 /**
@@ -383,13 +397,40 @@ static const struct override_param_map sc7280_snps_7nm_phy[] = {
 	{},
 };
 
+static const struct phy_reg_config hs_5nm_phy_pre_tuning[] = {
+	{ USB2_PHY_USB_PHY_CFG0, UTMI_PHY_CMN_CTRL_OVERRIDE_EN, UTMI_PHY_CMN_CTRL_OVERRIDE_EN },
+	{ USB2_PHY_USB_PHY_UTMI_CTRL5, POR, POR },
+	{ USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0, FSEL_MASK, 0 },
+	{ USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1, PLLBTUNE, PLLBTUNE },
+	{ USB2_PHY_USB_PHY_REFCLK_CTRL, REFCLK_SEL_MASK, REFCLK_SEL_DEFAULT },
+	{ USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1, VBUSVLDEXTSEL0, VBUSVLDEXTSEL0 },
+	{ USB2_PHY_USB_PHY_HS_PHY_CTRL1, VBUSVLDEXT0, VBUSVLDEXT0 },
+};
+
+static const struct phy_reg_config hs_5nm_phy_post_tuning[] = {
+	{ USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON2, VREGBYPASS, VREGBYPASS },
+	{ USB2_PHY_USB_PHY_HS_PHY_CTRL2, USB2_SUSPEND_N_SEL | USB2_SUSPEND_N,
+					 USB2_SUSPEND_N_SEL | USB2_SUSPEND_N },
+	{ USB2_PHY_USB_PHY_UTMI_CTRL0, SLEEPM, SLEEPM },
+	{ USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0, SIDDQ, 0 },
+	{ USB2_PHY_USB_PHY_UTMI_CTRL5, POR, 0 },
+	{ USB2_PHY_USB_PHY_HS_PHY_CTRL2, USB2_SUSPEND_N_SEL, 0 },
+	{ USB2_PHY_USB_PHY_CFG0, UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0 },
+};
+
 static int qcom_snps_hsphy_init(struct phy *phy)
 {
 	struct qcom_snps_hsphy *hsphy = phy_get_drvdata(phy);
+	const struct phy_config_data *data;
+	const struct phy_reg_config *tmp;
 	int ret, i;
 
 	dev_vdbg(&phy->dev, "%s(): Initializing SNPS HS phy\n", __func__);
 
+	data = of_device_get_match_data(hsphy->dev);
+	if (!data)
+		return -ENODEV;
+
 	ret = regulator_bulk_enable(ARRAY_SIZE(hsphy->vregs), hsphy->vregs);
 	if (ret)
 		return ret;
@@ -414,24 +455,8 @@ static int qcom_snps_hsphy_init(struct phy *phy)
 		goto disable_clks;
 	}
 
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_CFG0,
-					UTMI_PHY_CMN_CTRL_OVERRIDE_EN,
-					UTMI_PHY_CMN_CTRL_OVERRIDE_EN);
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_UTMI_CTRL5,
-							POR, POR);
-	qcom_snps_hsphy_write_mask(hsphy->base,
-					USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0,
-					FSEL_MASK, 0);
-	qcom_snps_hsphy_write_mask(hsphy->base,
-					USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1,
-					PLLBTUNE, PLLBTUNE);
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_REFCLK_CTRL,
-					REFCLK_SEL_MASK, REFCLK_SEL_DEFAULT);
-	qcom_snps_hsphy_write_mask(hsphy->base,
-					USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1,
-					VBUSVLDEXTSEL0, VBUSVLDEXTSEL0);
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL1,
-					VBUSVLDEXT0, VBUSVLDEXT0);
+	for (tmp = data->pre_tuning, i = 0; i < data->num_pre_tuning; i++, tmp++)
+		qcom_snps_hsphy_write_mask(hsphy->base, tmp->offset, tmp->mask, tmp->val);
 
 	for (i = 0; i < ARRAY_SIZE(hsphy->update_seq_cfg); i++) {
 		if (hsphy->update_seq_cfg[i].need_update)
@@ -441,28 +466,8 @@ static int qcom_snps_hsphy_init(struct phy *phy)
 					hsphy->update_seq_cfg[i].value);
 	}
 
-	qcom_snps_hsphy_write_mask(hsphy->base,
-					USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON2,
-					VREGBYPASS, VREGBYPASS);
-
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL2,
-					USB2_SUSPEND_N_SEL | USB2_SUSPEND_N,
-					USB2_SUSPEND_N_SEL | USB2_SUSPEND_N);
-
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_UTMI_CTRL0,
-					SLEEPM, SLEEPM);
-
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0,
-				   SIDDQ, 0);
-
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_UTMI_CTRL5,
-					POR, 0);
-
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL2,
-					USB2_SUSPEND_N_SEL, 0);
-
-	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_CFG0,
-					UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0);
+	for (tmp = data->post_tuning, i = 0; i < data->num_post_tuning; i++, tmp++)
+		qcom_snps_hsphy_write_mask(hsphy->base, tmp->offset, tmp->mask, tmp->val);
 
 	hsphy->phy_initialized = true;
 
@@ -495,14 +500,38 @@ static const struct phy_ops qcom_snps_hsphy_gen_ops = {
 	.owner		= THIS_MODULE,
 };
 
+static const struct phy_config_data hs_5nm_phy = {
+	.pre_tuning = hs_5nm_phy_pre_tuning,
+	.num_pre_tuning = ARRAY_SIZE(hs_5nm_phy_pre_tuning),
+	.post_tuning = hs_5nm_phy_post_tuning,
+	.num_post_tuning = ARRAY_SIZE(hs_5nm_phy_post_tuning),
+};
+
+static const struct phy_config_data hs_7nm_phy = {
+	.pre_tuning = hs_5nm_phy_pre_tuning,
+	.num_pre_tuning = ARRAY_SIZE(hs_5nm_phy_pre_tuning),
+	.override = sc7280_snps_7nm_phy,
+	.post_tuning = hs_5nm_phy_post_tuning,
+	.num_post_tuning = ARRAY_SIZE(hs_5nm_phy_post_tuning),
+};
+
 static const struct of_device_id qcom_snps_hsphy_of_match_table[] = {
-	{ .compatible	= "qcom,sm8150-usb-hs-phy", },
-	{ .compatible	= "qcom,usb-snps-hs-5nm-phy", },
+	{
+		.compatible	= "qcom,sm8150-usb-hs-phy",
+		.data		= &hs_5nm_phy,
+	},
+	{
+		.compatible	= "qcom,usb-snps-hs-5nm-phy",
+		.data		= &hs_5nm_phy,
+	},
 	{
 		.compatible	= "qcom,usb-snps-hs-7nm-phy",
-		.data		= &sc7280_snps_7nm_phy,
+		.data		= &hs_7nm_phy,
+	},
+	{
+		.compatible	= "qcom,usb-snps-femto-v2-phy",
+		.data		= &hs_5nm_phy,
 	},
-	{ .compatible	= "qcom,usb-snps-femto-v2-phy",	},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, qcom_snps_hsphy_of_match_table);
@@ -541,11 +570,14 @@ static void qcom_snps_hsphy_read_override_param_seq(struct device *dev)
 	s32 val;
 	int ret, i;
 	struct qcom_snps_hsphy *hsphy;
-	const struct override_param_map *cfg = of_device_get_match_data(dev);
+	const struct phy_config_data *data = of_device_get_match_data(dev);
+	const struct override_param_map *cfg;
 
-	if (!cfg)
+	if (!data || !data->override)
 		return;
 
+	cfg = data->override;
+
 	hsphy = dev_get_drvdata(dev);
 
 	for (i = 0; cfg[i].prop_name != NULL; i++) {

-- 
2.34.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v4 5/6] phy: qcom: snps-femto-v2: Move PHY init registers to config tables

[Dmitry Baryshkov]

On Mon, Oct 05, 2026 at 12:06:30PM +0530, Varadarajan Narayanan wrote:
> The driver currently programs the common PHY register sequence directly in
> qcom_snps_hsphy_init(), with the fixed register writes split around the
> override parameter handling. This makes it hard to support SoCs that need a
> different sequence or different values.
> 
> Move the fixed pre- and post-override register programming into per-
> compatible configuration tables, and keep the 7 nm override parameters in
> the same match-data structure. This allows the driver to share the common
> sequence while adding SoC-specific sequences for future platforms such as
> IPQ9650.
> 
> Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
> ---
>  drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 124 ++++++++++++++++----------
>  1 file changed, 78 insertions(+), 46 deletions(-)
> 
> -	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_HS_PHY_CTRL1,
> -					VBUSVLDEXT0, VBUSVLDEXT0);
> +	for (tmp = data->pre_tuning, i = 0; i < data->num_pre_tuning; i++, tmp++)
> +		qcom_snps_hsphy_write_mask(hsphy->base, tmp->offset, tmp->mask, tmp->val);

for (i = 0; i < data->num_pre_tuning; i++)
	qcom_snps_hsphy_write_mask(hsphy->base,
				   data->pre_tuning[i].offset,
				   data->pre_tuning[i].mask,
				   data->pre_tuning[i].val);

>  
>  	for (i = 0; i < ARRAY_SIZE(hsphy->update_seq_cfg); i++) {
>  		if (hsphy->update_seq_cfg[i].need_update)
> -	qcom_snps_hsphy_write_mask(hsphy->base, USB2_PHY_USB_PHY_CFG0,
> -					UTMI_PHY_CMN_CTRL_OVERRIDE_EN, 0);
> +	for (tmp = data->post_tuning, i = 0; i < data->num_post_tuning; i++, tmp++)
> +		qcom_snps_hsphy_write_mask(hsphy->base, tmp->offset, tmp->mask, tmp->val);

And here too.

>  
>  	hsphy->phy_initialized = true;
>  

-- 
With best wishes
Dmitry

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v4 4/6] phy: qcom: snps-femto-v2: Fix qcom_snps_hsphy_write_mask argument mixup

[Dmitry Baryshkov]

On Mon, Oct 05, 2026 at 12:06:29PM +0530, Varadarajan Narayanan wrote:
> Fix the register bit field mask & value argument mixup while programming

Fix the order of ... arguments.

With the commti message fixed:

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>




> USB2_PHY_USB_PHY_REFCLK_CTRL in qcom_snps_hsphy_init() and USB2_AUTO_RESUME
> in qcom_snps_hsphy_suspend().
> 
> Fixes: 51e8114f80d07 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
> Fixes: 0d75f508a9d56 ("phy: qcom-snps: Add runtime suspend and resume handlers")
> Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
> ---
>  drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 

-- 
With best wishes
Dmitry

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v4 6/6] phy: qcom: snps-femto-v2: Add IPQ9650 support

[Dmitry Baryshkov]

On Mon, Oct 05, 2026 at 12:06:31PM +0530, Varadarajan Narayanan wrote:
> Add the 6 nm SNPS femto USB2 PHY configuration needed by IPQ9650. The PHYs
> on this SoC require a dedicated init sequence and override parameters
> before they can be enabled.
> 
> Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
> ---
>  drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 62 +++++++++++++++++++++++++++
>  1 file changed, 62 insertions(+)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> index b6bbf2b570c7..8957f208bc51 100644
> --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> @@ -29,12 +29,15 @@
>  
>  #define USB2_PHY_USB_PHY_UTMI_CTRL5		(0x50)
>  #define POR					BIT(1)
> +#define ATERESET				BIT(0)
>  
>  #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0	(0x54)
>  #define SIDDQ					BIT(2)
>  #define RETENABLEN				BIT(3)
>  #define FSEL_MASK				GENMASK(6, 4)
>  #define FSEL_DEFAULT				(0x3 << 4)
> +#define FSEL_24MHZ				(0x2 << 4)

Use FIELD_PREP, please.

> +#define VATESTENB_MASK				GENMASK(1, 0)
>  
>  #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1	(0x58)
>  #define VBUSVLDEXTSEL0				BIT(4)

-- 
With best wishes
Dmitry

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v4 6/6] phy: qcom: snps-femto-v2: Add IPQ9650 support

[Varadarajan Narayanan]

On Mon, Oct 05, 2026 at 10:17:32AM +0300, Dmitry Baryshkov wrote:
> On Mon, Oct 05, 2026 at 12:06:31PM +0530, Varadarajan Narayanan wrote:
> > Add the 6 nm SNPS femto USB2 PHY configuration needed by IPQ9650. The PHYs
> > on this SoC require a dedicated init sequence and override parameters
> > before they can be enabled.
> >
> > Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
> > ---
> >  drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 62 +++++++++++++++++++++++++++
> >  1 file changed, 62 insertions(+)
> >
> > diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > index b6bbf2b570c7..8957f208bc51 100644
> > --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > @@ -29,12 +29,15 @@
> >
> >  #define USB2_PHY_USB_PHY_UTMI_CTRL5		(0x50)
> >  #define POR					BIT(1)
> > +#define ATERESET				BIT(0)
> >
> >  #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0	(0x54)
> >  #define SIDDQ					BIT(2)
> >  #define RETENABLEN				BIT(3)
> >  #define FSEL_MASK				GENMASK(6, 4)
> >  #define FSEL_DEFAULT				(0x3 << 4)
> > +#define FSEL_24MHZ				(0x2 << 4)
>
> Use FIELD_PREP, please.

Not able to use FIELD_PREP, getting this compilation error.

  CC      drivers/phy/qualcomm/phy-qcom-snps-femto-v2.o
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c:449:53: error: statement expression not allowed at file scope
  449 |         { USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0, FSEL_MASK, FSEL_24MHZ },
      |                                                            ^
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c:39:23: note: expanded from macro 'FSEL_24MHZ'
   39 | #define FSEL_24MHZ                              FIELD_PREP(FSEL_MASK, 2)
      |                                                 ^
./include/linux/bitfield.h:136:2: note: expanded from macro 'FIELD_PREP'
  136 |         ({                                                              \
      |         ^

Thanks
Varada

>
> > +#define VATESTENB_MASK				GENMASK(1, 0)
> >
> >  #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1	(0x58)
> >  #define VBUSVLDEXTSEL0				BIT(4)
>
> --
> With best wishes
> Dmitry

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v4 6/6] phy: qcom: snps-femto-v2: Add IPQ9650 support

[Dmitry Baryshkov]

On Mon, Oct 05, 2026 at 04:15:12PM +0530, Varadarajan Narayanan wrote:
> On Mon, Oct 05, 2026 at 10:17:32AM +0300, Dmitry Baryshkov wrote:
> > On Mon, Oct 05, 2026 at 12:06:31PM +0530, Varadarajan Narayanan wrote:
> > > Add the 6 nm SNPS femto USB2 PHY configuration needed by IPQ9650. The PHYs
> > > on this SoC require a dedicated init sequence and override parameters
> > > before they can be enabled.
> > >
> > > Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
> > > ---
> > >  drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 62 +++++++++++++++++++++++++++
> > >  1 file changed, 62 insertions(+)
> > >
> > > diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > > index b6bbf2b570c7..8957f208bc51 100644
> > > --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > > +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > > @@ -29,12 +29,15 @@
> > >
> > >  #define USB2_PHY_USB_PHY_UTMI_CTRL5		(0x50)
> > >  #define POR					BIT(1)
> > > +#define ATERESET				BIT(0)
> > >
> > >  #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0	(0x54)
> > >  #define SIDDQ					BIT(2)
> > >  #define RETENABLEN				BIT(3)
> > >  #define FSEL_MASK				GENMASK(6, 4)
> > >  #define FSEL_DEFAULT				(0x3 << 4)
> > > +#define FSEL_24MHZ				(0x2 << 4)
> >
> > Use FIELD_PREP, please.
> 
> Not able to use FIELD_PREP, getting this compilation error.

Sorry. Does FIELD_PREP_CONST work?

> 
>   CC      drivers/phy/qualcomm/phy-qcom-snps-femto-v2.o
> drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c:449:53: error: statement expression not allowed at file scope
>   449 |         { USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0, FSEL_MASK, FSEL_24MHZ },
>       |                                                            ^
> drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c:39:23: note: expanded from macro 'FSEL_24MHZ'
>    39 | #define FSEL_24MHZ                              FIELD_PREP(FSEL_MASK, 2)
>       |                                                 ^
> ./include/linux/bitfield.h:136:2: note: expanded from macro 'FIELD_PREP'
>   136 |         ({                                                              \
>       |         ^
> 
> Thanks
> Varada
> 
> >
> > > +#define VATESTENB_MASK				GENMASK(1, 0)
> > >
> > >  #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1	(0x58)
> > >  #define VBUSVLDEXTSEL0				BIT(4)
> >
> > --
> > With best wishes
> > Dmitry

-- 
With best wishes
Dmitry

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v4 6/6] phy: qcom: snps-femto-v2: Add IPQ9650 support

[Varadarajan Narayanan]

On Mon, Oct 05, 2026 at 02:01:48PM +0300, Dmitry Baryshkov wrote:
> On Mon, Oct 05, 2026 at 04:15:12PM +0530, Varadarajan Narayanan wrote:
> > On Mon, Oct 05, 2026 at 10:17:32AM +0300, Dmitry Baryshkov wrote:
> > > On Mon, Oct 05, 2026 at 12:06:31PM +0530, Varadarajan Narayanan wrote:
> > > > Add the 6 nm SNPS femto USB2 PHY configuration needed by IPQ9650. The PHYs
> > > > on this SoC require a dedicated init sequence and override parameters
> > > > before they can be enabled.
> > > >
> > > > Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
> > > > ---
> > > >  drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 62 +++++++++++++++++++++++++++
> > > >  1 file changed, 62 insertions(+)
> > > >
> > > > diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > > > index b6bbf2b570c7..8957f208bc51 100644
> > > > --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > > > +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > > > @@ -29,12 +29,15 @@
> > > >
> > > >  #define USB2_PHY_USB_PHY_UTMI_CTRL5		(0x50)
> > > >  #define POR					BIT(1)
> > > > +#define ATERESET				BIT(0)
> > > >
> > > >  #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0	(0x54)
> > > >  #define SIDDQ					BIT(2)
> > > >  #define RETENABLEN				BIT(3)
> > > >  #define FSEL_MASK				GENMASK(6, 4)
> > > >  #define FSEL_DEFAULT				(0x3 << 4)
> > > > +#define FSEL_24MHZ				(0x2 << 4)
> > >
> > > Use FIELD_PREP, please.
> >
> > Not able to use FIELD_PREP, getting this compilation error.
>
> Sorry. Does FIELD_PREP_CONST work?

Yes. Will post a new version...

Thanks
Varada

> >
> >   CC      drivers/phy/qualcomm/phy-qcom-snps-femto-v2.o
> > drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c:449:53: error: statement expression not allowed at file scope
> >   449 |         { USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0, FSEL_MASK, FSEL_24MHZ },
> >       |                                                            ^
> > drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c:39:23: note: expanded from macro 'FSEL_24MHZ'
> >    39 | #define FSEL_24MHZ                              FIELD_PREP(FSEL_MASK, 2)
> >       |                                                 ^
> > ./include/linux/bitfield.h:136:2: note: expanded from macro 'FIELD_PREP'
> >   136 |         ({                                                              \
> >       |         ^
> >
> > Thanks
> > Varada
> >
> > >
> > > > +#define VATESTENB_MASK				GENMASK(1, 0)
> > > >
> > > >  #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON1	(0x58)
> > > >  #define VBUSVLDEXTSEL0				BIT(4)
> > >
> > > --
> > > With best wishes
> > > Dmitry
>
> --
> With best wishes
> Dmitry

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v4 6/6] phy: qcom: snps-femto-v2: Add IPQ9650 support

[Vinod Koul]

On 05-10-26, 17:12, Varadarajan Narayanan wrote:
> On Mon, Oct 05, 2026 at 02:01:48PM +0300, Dmitry Baryshkov wrote:
> > On Mon, Oct 05, 2026 at 04:15:12PM +0530, Varadarajan Narayanan wrote:
> > > On Mon, Oct 05, 2026 at 10:17:32AM +0300, Dmitry Baryshkov wrote:
> > > > On Mon, Oct 05, 2026 at 12:06:31PM +0530, Varadarajan Narayanan wrote:
> > > > > Add the 6 nm SNPS femto USB2 PHY configuration needed by IPQ9650. The PHYs
> > > > > on this SoC require a dedicated init sequence and override parameters
> > > > > before they can be enabled.
> > > > >
> > > > > Signed-off-by: Varadarajan Narayanan <varadarajan.narayanan@oss.qualcomm.com>
> > > > > ---
> > > > >  drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c | 62 +++++++++++++++++++++++++++
> > > > >  1 file changed, 62 insertions(+)
> > > > >
> > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > > > > index b6bbf2b570c7..8957f208bc51 100644
> > > > > --- a/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > > > > +++ b/drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c
> > > > > @@ -29,12 +29,15 @@
> > > > >
> > > > >  #define USB2_PHY_USB_PHY_UTMI_CTRL5		(0x50)
> > > > >  #define POR					BIT(1)
> > > > > +#define ATERESET				BIT(0)
> > > > >
> > > > >  #define USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0	(0x54)
> > > > >  #define SIDDQ					BIT(2)
> > > > >  #define RETENABLEN				BIT(3)
> > > > >  #define FSEL_MASK				GENMASK(6, 4)
> > > > >  #define FSEL_DEFAULT				(0x3 << 4)
> > > > > +#define FSEL_24MHZ				(0x2 << 4)
> > > >
> > > > Use FIELD_PREP, please.
> > >
> > > Not able to use FIELD_PREP, getting this compilation error.
> >
> > Sorry. Does FIELD_PREP_CONST work?
> 
> Yes. Will post a new version...

Yes we have const version, there is also GENMASK and friends..

-- 
~Vinod

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy