[PATCH RFC 0/6] phy/media: Add generic MIPI C-PHY support to CSI-2 stack

[Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>]

George posted a C-PHY series [1] which we are currently reviewing.
As discussed with Bryan, this series shares our independent
implementation so the approaches can be compared.

Two aspects covered here are not in [1]:

- Settle count calculation derived from sensor-reported T_PREPARE and
  T_PREAMBLE timing via get_mbus_config(). [1] left this as an open
  question.

- Data rate based register sequence selection using effective bit
  rate (link_freq * 32 / 7). [1] noted downstream does this but
  deferred it; this series implements it.

MIPI CSI-2 operates over two physical layer variants. D-PHY uses a
dedicated differential clock lane with up to four data lanes. C-PHY
encodes the clock within the data stream across up to three wire
trios, eliminating the dedicated clock lane.

Patch 1 extends the generic PHY framework with PHY_MODE_MIPI_CPHY
and struct phy_configure_opts_mipi_cphy.

Patch 2 adds t_prepare_ns and t_preamble_ns fields to the CSI-2
media bus configuration and extends CAMSS to forward them to the PHY
provider for settle count calculation. Sensor drivers must implement
get_mbus_config() and return non-zero values in nanoseconds; stream-on
returns -EINVAL otherwise. The strictness is deliberate: C-PHY settle
timing is symbol-rate-range specific and no safe value can be derived
from link frequency alone. A conservative fallback could be added if
reviewers prefer.

Patches 3-6 extend the Qualcomm CSIPHY driver: refactor D-PHY
register storage to accommodate C-PHY, accept C-PHY mode with
multiple data rate table selection, compute settle count, and add
lane power mask support for C-PHY trios.

C-PHY encodes 16 bits per 7 symbols, so the effective bit rate is:

  bit_rate = link_freq * 2 * 16 / 7 = link_freq * 32 / 7

where link_freq is symbol_rate / 2 as reported by the sensor via
get_mbus_config(). The rate-table entry whose bandwidth first meets
or exceeds bit_rate is selected.

The settle count defines how many timer clock cycles the CSIPHY
receiver waits before scanning for C-PHY sync. It is computed from
the sensor's T_PREPARE and T_PREAMBLE timing. The /3 factor reflects
that C-PHY distributes the preamble sequence across three trios:

  settle_cnt = (t_prepare_ns + t_preamble_ns / 3) * timer_clk_rate / 1e9

D-PHY settle count is unchanged from before this series.

[1] https://lore.kernel.org/all/20261016-x1e-cphy-rfc-v3-0-40a346a72153@gmail.com/

Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
Nihal Kumar Gupta (6):
      phy: core: Add MIPI C-PHY configurations
      media: qcom: camss: Add C-PHY timing fields and get config from sensor
      phy: qcom: mipi-csi2: Split D-PHY register settings
      phy: qcom: mipi-csi2: Accept C-PHY mode and add register sequence
      phy: qcom: mipi-csi2: Add C-PHY settle calculation
      phy: qcom: mipi-csi2: Add lane mask calculation for C-PHY

 drivers/media/platform/qcom/camss/camss-csiphy.c   |  90 +++++++++---
 drivers/media/platform/qcom/camss/camss-csiphy.h   |   2 +
 drivers/media/platform/qcom/camss/camss.c          |   8 +-
 drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c | 159 +++++++++++++++++----
 drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c     |  51 +++++--
 drivers/phy/qualcomm/phy-qcom-mipi-csi2.h          |  25 +++-
 include/linux/phy/phy.h                            |  47 ++++++
 include/media/v4l2-mediabus.h                      |   2 +
 8 files changed, 315 insertions(+), 69 deletions(-)
---
base-commit: 2efb7a11f1aa4d2dc285fe2680cca22cb9f72f64
change-id: 20261017-cphy_support-2ce4d656e631

Best regards,
-- 
Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy