[PATCH v5 0/6] Add USB2.0 support

[PATCH v5 0/6] Add USB2.0 support

[Biju Das]

This patch series aims to add USB2.0 Host and device support for RZ/G2L SoC.

v4->v5:
 * Removed USBPHY control and binding patches as it is accepted for reset/next
 * Removed USB ehci/ohci binding patches as it is accepted for usb/next.
 * Updated Renesas USB2.0 PHY bindings to just use 'resets' as required.
 * Added interrupts maxitems=1 for SoC other than RZ/G2L for Renesas USBHS bindings
 * Updated the commit description for USB2.0 PHY driver patch.

v3->v4:
 * Added Rob's Acked-by tag for generic-{ohci,ehci} binding patch
 * Added Rob's Rb tag for RZ/G2L USBPHY control binding patch
 * Incorporated Philipp's review comments for USBPHY control driver.
 * Dropped second reset from usb2-phy binding patch
 * Added maxitems as per Rob's review comment.

v2->v3
 * USBPHY Control IP modelled as reset bindings as per Rob's suggestion
 * Updated the binding patches
 * Incorporated Geert's and Shimoda-San's review comment for phy driver patch.

v1->v2
 * Updated usb phy control bindings with clock definitions
 * Updated generic ohci/ehci bindings to support RZ/G2L SoC
 * Incorporated vinod's review comment on usb phy control driver
 * Add support for USB2.0 device and OTG support.

Biju Das (6):
  arm64: configs: defconfig: Enable RZ/G2L USBPHY control driver
  dt-bindings: phy: renesas,usb2-phy: Document RZ/G2L phy bindings
  phy: renesas: phy-rcar-gen3-usb2: Add USB2.0 PHY support for RZ/G2L
  arm64: dts: renesas: r9a07g044: Add USB2.0 phy and host support
  dt-bindings: usb: renesas,usbhs: Document RZ/G2L bindings
  arm64: dts: renesas: r9a07g044: Add USB2.0 device support

 .../bindings/phy/renesas,usb2-phy.yaml        |  15 +++
 .../bindings/usb/renesas,usbhs.yaml           |  26 +++-
 arch/arm64/boot/dts/renesas/r9a07g044.dtsi    | 113 ++++++++++++++++++
 arch/arm64/configs/defconfig                  |   1 +
 drivers/phy/renesas/phy-rcar-gen3-usb2.c      |  97 +++++++++++----
 5 files changed, 226 insertions(+), 26 deletions(-)

-- 
2.17.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v5 2/6] dt-bindings: phy: renesas, usb2-phy: Document RZ/G2L phy bindings

[Biju Das]

Document USB phy bindings for RZ/G2L SoC.

RZ/G2L USB2.0 phy uses line ctrl register for OTG_ID pin changes. It uses
a different OTG-BC interrupt bit for device recognition. Apart from this,
the PHY reset is controlled by USBPHY control IP and Document reset is a
required property.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
v4->v5:
 * Removed 'properties' and just used 'required' for RZ/G2L SoC.
v3->v4:
 * Removed second reset
 * Added family specific compatible string.
v2->v3
 * Created a new compatible for RZ/G2L as per Geert's suggestion.
 * Added resets required properties for RZ/G2L SoC.
---
 .../devicetree/bindings/phy/renesas,usb2-phy.yaml | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/renesas,usb2-phy.yaml b/Documentation/devicetree/bindings/phy/renesas,usb2-phy.yaml
index d5dc5a3cdceb..3a6e1165419c 100644
--- a/Documentation/devicetree/bindings/phy/renesas,usb2-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/renesas,usb2-phy.yaml
@@ -30,6 +30,11 @@ properties:
               - renesas,usb2-phy-r8a77995 # R-Car D3
           - const: renesas,rcar-gen3-usb2-phy
 
+      - items:
+          - enum:
+              - renesas,usb2-phy-r9a07g044 # RZ/G2{L,LC}
+          - const: renesas,rzg2l-usb2-phy  # RZ/G2L family
+
   reg:
     maxItems: 1
 
@@ -91,6 +96,16 @@ required:
   - clocks
   - '#phy-cells'
 
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: renesas,rzg2l-usb2-phy
+    then:
+      required:
+        - resets
+
 additionalProperties: false
 
 examples:
-- 
2.17.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v5 3/6] phy: renesas: phy-rcar-gen3-usb2: Add USB2.0 PHY support for RZ/G2L

[Biju Das]

This patch adds USB2.0 PHY support for RZ/G2L SoC.

We need to use a different compatible string due to some differences
with R-Car Gen3 USB2.0 PHY. It uses line ctrl register for OTG_ID
pin changes and different OTG-BC interrupt bit for device recognition.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
---
 v4->v5:
  * Updated commit description Add OTG support-> Add USB2.0 PHY support.
 v3->v4:
  * using family compatible instead of SoC specific.
 v3:
  * Made seperate compatible for RZ/G2L.
  * Extended rcar_gen3_phy_usb2_match_table[].data to support RZ/G2L.
---
 drivers/phy/renesas/phy-rcar-gen3-usb2.c | 97 ++++++++++++++++++------
 1 file changed, 73 insertions(+), 24 deletions(-)

diff --git a/drivers/phy/renesas/phy-rcar-gen3-usb2.c b/drivers/phy/renesas/phy-rcar-gen3-usb2.c
index fbc55232120e..9de617ca9daa 100644
--- a/drivers/phy/renesas/phy-rcar-gen3-usb2.c
+++ b/drivers/phy/renesas/phy-rcar-gen3-usb2.c
@@ -64,6 +64,7 @@
 /* VBCTRL */
 #define USB2_VBCTRL_OCCLREN		BIT(16)
 #define USB2_VBCTRL_DRVVBUSSEL		BIT(8)
+#define USB2_VBCTRL_VBOUT		BIT(0)
 
 /* LINECTRL1 */
 #define USB2_LINECTRL1_DPRPD_EN		BIT(19)
@@ -78,6 +79,10 @@
 #define USB2_ADPCTRL_IDPULLUP		BIT(5)	/* 1 = ID sampling is enabled */
 #define USB2_ADPCTRL_DRVVBUS		BIT(4)
 
+/*  RZ/G2L specific */
+#define USB2_OBINT_IDCHG_EN		BIT(0)
+#define USB2_LINECTRL1_USB2_IDMON	BIT(0)
+
 #define NUM_OF_PHYS			4
 enum rcar_gen3_phy_index {
 	PHY_INDEX_BOTH_HC,
@@ -112,9 +117,16 @@ struct rcar_gen3_chan {
 	struct mutex lock;	/* protects rphys[...].powered */
 	enum usb_dr_mode dr_mode;
 	int irq;
+	u32 obint_enable_bits;
 	bool extcon_host;
 	bool is_otg_channel;
 	bool uses_otg_pins;
+	bool soc_no_adp_ctrl;
+};
+
+struct rcar_gen3_phy_drv_data {
+	const struct phy_ops *phy_usb2_ops;
+	bool no_adp_ctrl;
 };
 
 /*
@@ -172,14 +184,22 @@ static void rcar_gen3_set_linectrl(struct rcar_gen3_chan *ch, int dp, int dm)
 static void rcar_gen3_enable_vbus_ctrl(struct rcar_gen3_chan *ch, int vbus)
 {
 	void __iomem *usb2_base = ch->base;
-	u32 val = readl(usb2_base + USB2_ADPCTRL);
+	u32 vbus_ctrl_reg = USB2_ADPCTRL;
+	u32 vbus_ctrl_val = USB2_ADPCTRL_DRVVBUS;
+	u32 val;
 
 	dev_vdbg(ch->dev, "%s: %08x, %d\n", __func__, val, vbus);
+	if (ch->soc_no_adp_ctrl) {
+		vbus_ctrl_reg = USB2_VBCTRL;
+		vbus_ctrl_val = USB2_VBCTRL_VBOUT;
+	}
+
+	val = readl(usb2_base + vbus_ctrl_reg);
 	if (vbus)
-		val |= USB2_ADPCTRL_DRVVBUS;
+		val |= vbus_ctrl_val;
 	else
-		val &= ~USB2_ADPCTRL_DRVVBUS;
-	writel(val, usb2_base + USB2_ADPCTRL);
+		val &= ~vbus_ctrl_val;
+	writel(val, usb2_base + vbus_ctrl_reg);
 }
 
 static void rcar_gen3_control_otg_irq(struct rcar_gen3_chan *ch, int enable)
@@ -188,9 +208,9 @@ static void rcar_gen3_control_otg_irq(struct rcar_gen3_chan *ch, int enable)
 	u32 val = readl(usb2_base + USB2_OBINTEN);
 
 	if (ch->uses_otg_pins && enable)
-		val |= USB2_OBINT_BITS;
+		val |= ch->obint_enable_bits;
 	else
-		val &= ~USB2_OBINT_BITS;
+		val &= ~ch->obint_enable_bits;
 	writel(val, usb2_base + USB2_OBINTEN);
 }
 
@@ -252,6 +272,9 @@ static bool rcar_gen3_check_id(struct rcar_gen3_chan *ch)
 	if (!ch->uses_otg_pins)
 		return (ch->dr_mode == USB_DR_MODE_HOST) ? false : true;
 
+	if (ch->soc_no_adp_ctrl)
+		return !!(readl(ch->base + USB2_LINECTRL1) & USB2_LINECTRL1_USB2_IDMON);
+
 	return !!(readl(ch->base + USB2_ADPCTRL) & USB2_ADPCTRL_IDDIG);
 }
 
@@ -376,16 +399,17 @@ static void rcar_gen3_init_otg(struct rcar_gen3_chan *ch)
 	      USB2_LINECTRL1_DMRPD_EN | USB2_LINECTRL1_DM_RPD;
 	writel(val, usb2_base + USB2_LINECTRL1);
 
-	val = readl(usb2_base + USB2_VBCTRL);
-	val &= ~USB2_VBCTRL_OCCLREN;
-	writel(val | USB2_VBCTRL_DRVVBUSSEL, usb2_base + USB2_VBCTRL);
-	val = readl(usb2_base + USB2_ADPCTRL);
-	writel(val | USB2_ADPCTRL_IDPULLUP, usb2_base + USB2_ADPCTRL);
-
+	if (!ch->soc_no_adp_ctrl) {
+		val = readl(usb2_base + USB2_VBCTRL);
+		val &= ~USB2_VBCTRL_OCCLREN;
+		writel(val | USB2_VBCTRL_DRVVBUSSEL, usb2_base + USB2_VBCTRL);
+		val = readl(usb2_base + USB2_ADPCTRL);
+		writel(val | USB2_ADPCTRL_IDPULLUP, usb2_base + USB2_ADPCTRL);
+	}
 	msleep(20);
 
 	writel(0xffffffff, usb2_base + USB2_OBINTSTA);
-	writel(USB2_OBINT_BITS, usb2_base + USB2_OBINTEN);
+	writel(ch->obint_enable_bits, usb2_base + USB2_OBINTEN);
 
 	rcar_gen3_device_recognition(ch);
 }
@@ -397,9 +421,9 @@ static irqreturn_t rcar_gen3_phy_usb2_irq(int irq, void *_ch)
 	u32 status = readl(usb2_base + USB2_OBINTSTA);
 	irqreturn_t ret = IRQ_NONE;
 
-	if (status & USB2_OBINT_BITS) {
+	if (status & ch->obint_enable_bits) {
 		dev_vdbg(ch->dev, "%s: %08x\n", __func__, status);
-		writel(USB2_OBINT_BITS, usb2_base + USB2_OBINTSTA);
+		writel(ch->obint_enable_bits, usb2_base + USB2_OBINTSTA);
 		rcar_gen3_device_recognition(ch);
 		ret = IRQ_HANDLED;
 	}
@@ -535,26 +559,45 @@ static const struct phy_ops rz_g1c_phy_usb2_ops = {
 	.owner		= THIS_MODULE,
 };
 
+static const struct rcar_gen3_phy_drv_data rcar_gen3_phy_usb2_data = {
+	.phy_usb2_ops = &rcar_gen3_phy_usb2_ops,
+	.no_adp_ctrl = false,
+};
+
+static const struct rcar_gen3_phy_drv_data rz_g1c_phy_usb2_data = {
+	.phy_usb2_ops = &rz_g1c_phy_usb2_ops,
+	.no_adp_ctrl = false,
+};
+
+static const struct rcar_gen3_phy_drv_data rz_g2l_phy_usb2_data = {
+	.phy_usb2_ops = &rcar_gen3_phy_usb2_ops,
+	.no_adp_ctrl = true,
+};
+
 static const struct of_device_id rcar_gen3_phy_usb2_match_table[] = {
 	{
 		.compatible = "renesas,usb2-phy-r8a77470",
-		.data = &rz_g1c_phy_usb2_ops,
+		.data = &rz_g1c_phy_usb2_data,
 	},
 	{
 		.compatible = "renesas,usb2-phy-r8a7795",
-		.data = &rcar_gen3_phy_usb2_ops,
+		.data = &rcar_gen3_phy_usb2_data,
 	},
 	{
 		.compatible = "renesas,usb2-phy-r8a7796",
-		.data = &rcar_gen3_phy_usb2_ops,
+		.data = &rcar_gen3_phy_usb2_data,
 	},
 	{
 		.compatible = "renesas,usb2-phy-r8a77965",
-		.data = &rcar_gen3_phy_usb2_ops,
+		.data = &rcar_gen3_phy_usb2_data,
+	},
+	{
+		.compatible = "renesas,rzg2l-usb2-phy",
+		.data = &rz_g2l_phy_usb2_data,
 	},
 	{
 		.compatible = "renesas,rcar-gen3-usb2-phy",
-		.data = &rcar_gen3_phy_usb2_ops,
+		.data = &rcar_gen3_phy_usb2_data,
 	},
 	{ /* sentinel */ },
 };
@@ -608,10 +651,10 @@ static enum usb_dr_mode rcar_gen3_get_dr_mode(struct device_node *np)
 
 static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev)
 {
+	const struct rcar_gen3_phy_drv_data *phy_data;
 	struct device *dev = &pdev->dev;
 	struct rcar_gen3_chan *channel;
 	struct phy_provider *provider;
-	const struct phy_ops *phy_usb2_ops;
 	int ret = 0, i;
 
 	if (!dev->of_node) {
@@ -627,6 +670,7 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev)
 	if (IS_ERR(channel->base))
 		return PTR_ERR(channel->base);
 
+	channel->obint_enable_bits = USB2_OBINT_BITS;
 	/* get irq number here and request_irq for OTG in phy_init */
 	channel->irq = platform_get_irq_optional(pdev, 0);
 	channel->dr_mode = rcar_gen3_get_dr_mode(dev->of_node);
@@ -653,16 +697,21 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev)
 	 * And then, phy-core will manage runtime pm for this device.
 	 */
 	pm_runtime_enable(dev);
-	phy_usb2_ops = of_device_get_match_data(dev);
-	if (!phy_usb2_ops) {
+
+	phy_data = of_device_get_match_data(dev);
+	if (!phy_data) {
 		ret = -EINVAL;
 		goto error;
 	}
 
+	channel->soc_no_adp_ctrl = phy_data->no_adp_ctrl;
+	if (phy_data->no_adp_ctrl)
+		channel->obint_enable_bits = USB2_OBINT_IDCHG_EN;
+
 	mutex_init(&channel->lock);
 	for (i = 0; i < NUM_OF_PHYS; i++) {
 		channel->rphys[i].phy = devm_phy_create(dev, NULL,
-							phy_usb2_ops);
+							phy_data->phy_usb2_ops);
 		if (IS_ERR(channel->rphys[i].phy)) {
 			dev_err(dev, "Failed to create USB2 PHY\n");
 			ret = PTR_ERR(channel->rphys[i].phy);
-- 
2.17.1


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v5 2/6] dt-bindings: phy: renesas,usb2-phy: Document RZ/G2L phy bindings

[Rob Herring]

On Tue, 27 Jul 2021 19:55:23 +0100, Biju Das wrote:
> Document USB phy bindings for RZ/G2L SoC.
> 
> RZ/G2L USB2.0 phy uses line ctrl register for OTG_ID pin changes. It uses
> a different OTG-BC interrupt bit for device recognition. Apart from this,
> the PHY reset is controlled by USBPHY control IP and Document reset is a
> required property.
> 
> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> ---
> v4->v5:
>  * Removed 'properties' and just used 'required' for RZ/G2L SoC.
> v3->v4:
>  * Removed second reset
>  * Added family specific compatible string.
> v2->v3
>  * Created a new compatible for RZ/G2L as per Geert's suggestion.
>  * Added resets required properties for RZ/G2L SoC.
> ---
>  .../devicetree/bindings/phy/renesas,usb2-phy.yaml | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

RE: [PATCH v5 2/6] dt-bindings: phy: renesas,usb2-phy: Document RZ/G2L phy bindings

[Yoshihiro Shimoda]

Hi Biju-san,

> From: Biju Das, Sent: Wednesday, July 28, 2021 3:55 AM
> 
> Document USB phy bindings for RZ/G2L SoC.
> 
> RZ/G2L USB2.0 phy uses line ctrl register for OTG_ID pin changes. It uses
> a different OTG-BC interrupt bit for device recognition. Apart from this,
> the PHY reset is controlled by USBPHY control IP and Document reset is a
> required property.
> 
> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>

Thank you for the patch!

Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>

Best regards,
Yoshihiro Shimoda


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

RE: [PATCH v5 3/6] phy: renesas: phy-rcar-gen3-usb2: Add USB2.0 PHY support for RZ/G2L

[Yoshihiro Shimoda]

Hi Biju-san,

> From: Biju Das, Sent: Wednesday, July 28, 2021 3:55 AM
> 
> This patch adds USB2.0 PHY support for RZ/G2L SoC.
> 
> We need to use a different compatible string due to some differences
> with R-Car Gen3 USB2.0 PHY. It uses line ctrl register for OTG_ID
> pin changes and different OTG-BC interrupt bit for device recognition.
> 
> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>

Thank you for the patch!

Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>

Also, I tested this on my environment (r8a77951-salvator-xs),
and I didn't observe any regression. So,

Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> # on R-Car

Best regards,
Yoshihiro Shimoda


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v5 2/6] dt-bindings: phy: renesas,usb2-phy: Document RZ/G2L phy bindings

[Vinod Koul]

On 27-07-21, 19:55, Biju Das wrote:
> Document USB phy bindings for RZ/G2L SoC.
> 
> RZ/G2L USB2.0 phy uses line ctrl register for OTG_ID pin changes. It uses
> a different OTG-BC interrupt bit for device recognition. Apart from this,
> the PHY reset is controlled by USBPHY control IP and Document reset is a
> required property.

Applied, thanks

-- 
~Vinod

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v5 3/6] phy: renesas: phy-rcar-gen3-usb2: Add USB2.0 PHY support for RZ/G2L

[Vinod Koul]

On 27-07-21, 19:55, Biju Das wrote:
> This patch adds USB2.0 PHY support for RZ/G2L SoC.
> 
> We need to use a different compatible string due to some differences
> with R-Car Gen3 USB2.0 PHY. It uses line ctrl register for OTG_ID
> pin changes and different OTG-BC interrupt bit for device recognition.

Applied, thanks

-- 
~Vinod

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy