Re: [PATCH v4 2/2] phy: qcom: qmp-pcie: Add PHY register retention support

From: "Wenbin Yao (Consultant)" <quic_wenbyao@quicinc.com>
To: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>,
	Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Cc: <vkoul@kernel.org>, <kishon@kernel.org>, <p.zabel@pengutronix.de>,
	<dmitry.baryshkov@linaro.org>, <abel.vesa@linaro.org>,
	<quic_qianyu@quicinc.com>, <neil.armstrong@linaro.org>,
	<quic_devipriy@quicinc.com>, <linux-arm-msm@vger.kernel.org>,
	<linux-phy@lists.infradead.org>, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v4 2/2] phy: qcom: qmp-pcie: Add PHY register retention support
Date: Tue, 25 Feb 2025 16:06:16 +0800	[thread overview]
Message-ID: <eea55dfa-3dd3-488b-958c-cd20e18a7d7d@quicinc.com> (raw)
In-Reply-To: <20250224122439.njrcoyrfsisddoer@thinkpad>

On 2/24/2025 8:24 PM, Manivannan Sadhasivam wrote:
> On Mon, Feb 24, 2025 at 12:46:44PM +0100, Konrad Dybcio wrote:
>> On 24.02.2025 9:46 AM, Wenbin Yao (Consultant) wrote:
>>> On 2/24/2025 3:33 PM, Manivannan Sadhasivam wrote:
>>>> On Thu, Feb 20, 2025 at 06:22:53PM +0800, Wenbin Yao wrote:
>>>>> From: Qiang Yu <quic_qianyu@quicinc.com>
>>>>>
>>>>> Some QCOM PCIe PHYs support no_csr reset. Unlike BCR reset which resets the
>>>>> whole PHY (hardware and register), no_csr reset only resets PHY hardware
>>>>> but retains register values, which means PHY setting can be skipped during
>>>>> PHY init if PCIe link is enabled in booltloader and only no_csr is toggled
>>>>> after that.
>>>>>
>>>>> Hence, determine whether the PHY has been enabled in bootloader by
>>>>> verifying QPHY_START_CTRL register. If it's programmed and no_csr reset is
>>>>> available, skip BCR reset and PHY register setting to establish the PCIe
>>>>> link with bootloader - programmed PHY settings.
>>>>>
>>>>> Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
>>>>> Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
>>>> Some nitpicks below.
>>>>
>>>>> ---
>> [...]
>>
>>>>> +     * In this way, no matter whether the PHY settings were initially
>>>>> +     * programmed by bootloader or PHY driver itself, we can reuse them
>>>> It is really possible to have bootloader not programming the init sequence for
>>>> no_csr reset platforms? The comment sounds like it is possible. But I heard the
>>>> opposite.
>>> PCIe3 on X1E80100 QCP is disabled by default in UEFI. We need to enable it
>>> manually in UEFI shell if we want.
>> IIUC this will not be a concern going forward, and this is a special case
>>
> I'm wondering how many *special* cases we may have to deal with going forward.
> Anyhow, I would propose to atleast throw an error and fail probe() if:
>
> * the platform has no_csr reset AND
> * bootloader has not initialized the PHY AND
> * there are no init sequences in the kernel
>
> - Mani

Hmmm, regardless of whether it's a special case, we can't assume that UEFI
will enable the PHY supporting no_csr reset on all platforms. It's a bit
risky. If we make such an assumption, we also won't need to check whether
the PHY is enabled by UEFI during powering on. We just need to check
whether no_csr reset is available.

But it makes sense to check the exsitence of PHY senquence. How about
adding the check in qmp_pcie_init, if a PHY supports no_csr reset and isn't
initialized in UEFI and there is no cfg->tbls, return error and print some
error log so that the PCIe controller will fail to probe.

-- 
With best wishes
Wenbin

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy