[PATCH 1/8] PCI PM: Add function for checking PME status of devices

[PATCH 1/8] PCI PM: Add function for checking PME status of devices

[Rafael J. Wysocki]

From: Rafael J. Wysocki <rjw@sisk.pl>

Add function pci_check_pme_status() that will check the PME status
bit of given device and clear it along with the PME enable bit.  It
will be necessary for PCI run-time power management.

Based on a patch from Shaohua Li <shaohua.li@intel.com>

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 drivers/pci/pci.c |   35 +++++++++++++++++++++++++++++++++++
 drivers/pci/pci.h |    1 +
 2 files changed, 36 insertions(+)

Index: linux-2.6/drivers/pci/pci.h
===================================================================
--- linux-2.6.orig/drivers/pci/pci.h
+++ linux-2.6/drivers/pci/pci.h
@@ -49,6 +49,7 @@ struct pci_platform_pm_ops {
 extern int pci_set_platform_pm(struct pci_platform_pm_ops *ops);
 extern void pci_update_current_state(struct pci_dev *dev, pci_power_t state);
 extern void pci_disable_enabled_device(struct pci_dev *dev);
+extern bool pci_check_pme_status(struct pci_dev *dev);
 extern void pci_pm_init(struct pci_dev *dev);
 extern void platform_pci_wakeup_init(struct pci_dev *dev);
 extern void pci_allocate_cap_save_buffers(struct pci_dev *dev);
Index: linux-2.6/drivers/pci/pci.c
===================================================================
--- linux-2.6.orig/drivers/pci/pci.c
+++ linux-2.6/drivers/pci/pci.c
@@ -1195,6 +1195,41 @@ int pci_set_pcie_reset_state(struct pci_
 }
 
 /**
+ * pci_check_pme_status - Check if given device has generated PME.
+ * @dev: Device to check.
+ *
+ * Check the PME status of the device and if set, clear it and clear PME enable
+ * (if set).  Return 'true' if PME status and PME enable were both set or
+ * 'false' otherwise.
+ */
+bool pci_check_pme_status(struct pci_dev *dev)
+{
+	int pmcsr_pos;
+	u16 pmcsr;
+	bool ret = false;
+
+	if (!dev->pm_cap)
+		return false;
+
+	pmcsr_pos = dev->pm_cap + PCI_PM_CTRL;
+	pci_read_config_word(dev, pmcsr_pos, &pmcsr);
+	if (!(pmcsr & PCI_PM_CTRL_PME_STATUS))
+		return false;
+
+	/* Clear PME status. */
+	pmcsr |= PCI_PM_CTRL_PME_STATUS;
+	if (pmcsr & PCI_PM_CTRL_PME_ENABLE) {
+		/* Disable PME to avoid interrupt flood. */
+		pmcsr &= ~PCI_PM_CTRL_PME_ENABLE;
+		ret = true;
+	}
+
+	pci_write_config_word(dev, pmcsr_pos, pmcsr);
+
+	return ret;
+}
+
+/**
  * pci_pme_capable - check the capability of PCI device to generate PME#
  * @dev: PCI device to handle.
  * @state: PCI state from which device will issue PME#.

[PATCH 2/8] PCI PM: PCIe PME root port service driver (rev. 5)

[Rafael J. Wysocki]

From: Rafael J. Wysocki <rjw@sisk.pl>

PCIe native PME detection mechanism is based on interrupts generated
by root ports or event collectors every time a PCIe device sends a
PME message upstream.

Once a PME message has been sent by an endpoint device and received
by its root port (or event collector in the case of root complex
integrated endpoints), the Requester ID from the message header is
registered in the root port's Root Status register.  At the same
time, the PME Status bit of the Root Status register is set to
indicate that there's a PME to handle.  If PCIe PME interrupt is
enabled for the root port, it generates an interrupt once the PME
Status has been set.  After receiving the interrupt, the kernel can
identify the PCIe device that generated the PME using the Requester
ID from the root port's Root Status register. [For details, see PCI
Express Base Specification, Rev. 2.0.]

Implement a driver for the PCIe PME root port service working in
accordance with the above description.

Based on a patch from Shaohua Li <shaohua.li@intel.com>.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 Documentation/kernel-parameters.txt  |    6 
 drivers/pci/pcie/Kconfig             |    4 
 drivers/pci/pcie/Makefile            |    2 
 drivers/pci/pcie/pme/Makefile        |    8 
 drivers/pci/pcie/pme/pcie_pme.c      |  493 +++++++++++++++++++++++++++++++++++
 drivers/pci/pcie/pme/pcie_pme.h      |   28 +
 drivers/pci/pcie/pme/pcie_pme_acpi.c |   54 +++
 include/linux/pci.h                  |    1 
 8 files changed, 596 insertions(+)

Index: linux-2.6/drivers/pci/pcie/Kconfig
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/Kconfig
+++ linux-2.6/drivers/pci/pcie/Kconfig
@@ -46,3 +46,7 @@ config PCIEASPM_DEBUG
 	help
 	  This enables PCI Express ASPM debug support. It will add per-device
 	  interface to control ASPM.
+
+config PCIE_PME
+	def_bool y
+	depends on PCIEPORTBUS && PM_RUNTIME && EXPERIMENTAL && ACPI
Index: linux-2.6/drivers/pci/pcie/Makefile
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/Makefile
+++ linux-2.6/drivers/pci/pcie/Makefile
@@ -11,3 +11,5 @@ obj-$(CONFIG_PCIEPORTBUS)	+= pcieportdrv
 
 # Build PCI Express AER if needed
 obj-$(CONFIG_PCIEAER)		+= aer/
+
+obj-$(CONFIG_PCIE_PME) += pme/
Index: linux-2.6/drivers/pci/pcie/pme/pcie_pme.c
===================================================================
--- /dev/null
+++ linux-2.6/drivers/pci/pcie/pme/pcie_pme.c
@@ -0,0 +1,493 @@
+/*
+ * PCIe Native PME support
+ *
+ * Copyright (C) 2007 - 2009 Intel Corp
+ * Copyright (C) 2007 - 2009 Shaohua Li <shaohua.li@intel.com>
+ * Copyright (C) 2009 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License V2.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/pcieport_if.h>
+#include <linux/acpi.h>
+#include <linux/pci-acpi.h>
+#include <linux/pm_runtime.h>
+
+#include "../../pci.h"
+#include "pcie_pme.h"
+
+#define PCI_EXP_RTSTA_PME	0x10000 /* PME status */
+#define PCI_EXP_RTSTA_PENDING	0x20000 /* PME pending */
+
+/*
+ * If set, this switch will prevent the PCIe root port PME service driver from
+ * being registered.  Consequently, the interrupt-based PCIe PME signaling will
+ * not be used by any PCIe root ports in that case.
+ */
+static bool pcie_pme_disabled;
+
+/*
+ * The PCI Express Base Specification 2.0, Section 6.1.8, states the following:
+ * "In order to maintain compatibility with non-PCI Express-aware system
+ * software, system power management logic must be configured by firmware to use
+ * the legacy mechanism of signaling PME by default.  PCI Express-aware system
+ * software must notify the firmware prior to enabling native, interrupt-based
+ * PME signaling."  However, if the platform doesn't provide us with a suitable
+ * notification mechanism or the notification fails, it is not clear whether or
+ * not we are supposed to use the interrupt-based PCIe PME signaling.  The
+ * switch below can be used to indicate the desired behaviour.  When set, it
+ * will make the kernel use the interrupt-based PCIe PME signaling regardless of
+ * the platform notification status, although the kernel will attempt to notify
+ * the platform anyway.  When unset, it will prevent the kernel from using the
+ * the interrupt-based PCIe PME signaling if the platform notification fails,
+ * which is the default.
+ */
+static bool pcie_pme_force_enable;
+
+static int __init pcie_pme_setup(char *str)
+{
+	if (!strcmp(str, "off"))
+		pcie_pme_disabled = true;
+	else if (!strcmp(str, "force"))
+		pcie_pme_force_enable = true;
+	return 1;
+}
+__setup("pcie_pme=", pcie_pme_setup);
+
+/**
+ * pcie_pme_platform_setup - Ensure that the kernel controls the PCIe PME.
+ * @srv: PCIe PME root port service to use for carrying out the check.
+ *
+ * Notify the platform that the native PCIe PME is going to be used and return
+ * 'true' if the control of the PCIe PME registers has been acquired from the
+ * platform.
+ */
+static bool pcie_pme_platform_setup(struct pcie_device *srv)
+{
+	return !pcie_pme_platform_notify(srv) || pcie_pme_force_enable;
+}
+
+struct pcie_pme_service_data {
+	spinlock_t lock;
+	struct pcie_device *srv;
+	struct work_struct work;
+	bool noirq; /* Don't enable the PME interrupt used by this service. */
+};
+
+/**
+ * pcie_pme_interrupt_enable - Enable/disable PCIe PME interrupt generation.
+ * @dev: PCIe root port or event collector.
+ * @enable: Enable or disable the interrupt.
+ */
+static void pcie_pme_interrupt_enable(struct pci_dev *dev, bool enable)
+{
+	int rtctl_pos;
+	u16 rtctl;
+
+	rtctl_pos = pci_find_capability(dev, PCI_CAP_ID_EXP) + PCI_EXP_RTCTL;
+
+	pci_read_config_word(dev, rtctl_pos, &rtctl);
+	if (enable)
+		rtctl |= PCI_EXP_RTCTL_PMEIE;
+	else
+		rtctl &= ~PCI_EXP_RTCTL_PMEIE;
+	pci_write_config_word(dev, rtctl_pos, rtctl);
+}
+
+/**
+ * pcie_pme_clear_status - Clear root port PME interrupt status.
+ * @dev: PCIe root port or event collector.
+ */
+static void pcie_pme_clear_status(struct pci_dev *dev)
+{
+	int rtsta_pos;
+	u32 rtsta;
+
+	rtsta_pos = pci_find_capability(dev, PCI_CAP_ID_EXP) + PCI_EXP_RTSTA;
+
+	pci_read_config_dword(dev, rtsta_pos, &rtsta);
+	rtsta |= PCI_EXP_RTSTA_PME;
+	pci_write_config_dword(dev, rtsta_pos, rtsta);
+}
+
+/**
+ * pcie_pme_walk_bus - Scan a PCI bus for devices asserting PME#.
+ * @bus: PCI bus to scan.
+ *
+ * Scan given PCI bus and all buses under it for devices asserting PME#.
+ */
+static bool pcie_pme_walk_bus(struct pci_bus *bus)
+{
+	struct pci_dev *dev;
+	bool ret = false;
+
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		/* Skip PCIe devices in case we started from a root port. */
+		if (!dev->is_pcie && pci_check_pme_status(dev)) {
+			pm_request_resume(&dev->dev);
+			ret = true;
+		}
+
+		if (dev->subordinate && pcie_pme_walk_bus(dev->subordinate))
+			ret = true;
+	}
+
+	return ret;
+}
+
+/**
+ * pcie_pme_from_pci_bridge - Check if PCIe-PCI bridge generated a PME.
+ * @bus: Secondary bus of the bridge.
+ * @devfn: Device/function number to check.
+ *
+ * PME from PCI devices under a PCIe-PCI bridge may be converted to an in-band
+ * PCIe PME message.  In such that case the bridge should use the Requester ID
+ * of device/function number 0 on its secondary bus.
+ */
+static bool pcie_pme_from_pci_bridge(struct pci_bus *bus, u8 devfn)
+{
+	struct pci_dev *dev;
+	bool found = false;
+
+	if (devfn)
+		return false;
+
+	dev = pci_dev_get(bus->self);
+	if (!dev)
+		return false;
+
+	if (dev->is_pcie && dev->pcie_type == PCI_EXP_TYPE_PCI_BRIDGE) {
+		down_read(&pci_bus_sem);
+		if (pcie_pme_walk_bus(bus))
+			found = true;
+		up_read(&pci_bus_sem);
+	}
+
+	pci_dev_put(dev);
+	return found;
+}
+
+/**
+ * pcie_pme_handle_request - Find device that generated PME and handle it.
+ * @port: Root port or event collector that generated the PME interrupt.
+ * @req_id: PCIe Requester ID of the device that generated the PME.
+ */
+static void pcie_pme_handle_request(struct pci_dev *port, u16 req_id)
+{
+	u8 busnr = req_id >> 8, devfn = req_id & 0xff;
+	struct pci_bus *bus;
+	struct pci_dev *dev;
+	bool found = false;
+
+	/* First, check if the PME is from the root port itself. */
+	if (port->devfn == devfn && port->bus->number == busnr) {
+		if (pci_check_pme_status(port)) {
+			pm_request_resume(&port->dev);
+			found = true;
+		} else {
+			/*
+			 * Apparently, the root port generated the PME on behalf
+			 * of a non-PCIe device downstream.  If this is done by
+			 * a root port, the Requester ID field in its status
+			 * register may contain either the root port's, or the
+			 * source device's information (PCI Express Base
+			 * Specification, Rev. 2.0, Section 6.1.9).
+			 */
+			down_read(&pci_bus_sem);
+			found = pcie_pme_walk_bus(port->subordinate);
+			up_read(&pci_bus_sem);
+		}
+		goto out;
+	}
+
+	/* Second, find the bus the source device is on. */
+	bus = pci_find_bus(pci_domain_nr(port->bus), busnr);
+	if (!bus)
+		goto out;
+
+	/* Next, check if the PME is from a PCIe-PCI bridge. */
+	found = pcie_pme_from_pci_bridge(bus, devfn);
+	if (found)
+		goto out;
+
+	/* Finally, try to find the PME source on the bus. */
+	down_read(&pci_bus_sem);
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		pci_dev_get(dev);
+		if (dev->devfn == devfn) {
+			found = true;
+			break;
+		}
+		pci_dev_put(dev);
+	}
+	up_read(&pci_bus_sem);
+
+	if (found) {
+		/* The device is there, but we have to check its PME status. */
+		found = pci_check_pme_status(dev);
+		if (found)
+			pm_request_resume(&dev->dev);
+		pci_dev_put(dev);
+	} else if (devfn) {
+		/*
+		 * The device is not there, but we can still try to recover by
+		 * assuming that the PME was reported by a PCIe-PCI bridge that
+		 * used devfn different from zero.
+		 */
+		dev_dbg(&port->dev, "PME interrupt generated for "
+			"non-existent device %02x:%02x.%d\n",
+			busnr, PCI_SLOT(devfn), PCI_FUNC(devfn));
+		found = pcie_pme_from_pci_bridge(bus, 0);
+	}
+
+ out:
+	if (!found)
+		dev_dbg(&port->dev, "Spurious native PME interrupt!\n");
+}
+
+/**
+ * pcie_pme_work_fn - Work handler for PCIe PME interrupt.
+ * @work: Work structure giving access to service data.
+ */
+static void pcie_pme_work_fn(struct work_struct *work)
+{
+	struct pcie_pme_service_data *data =
+			container_of(work, struct pcie_pme_service_data, work);
+	struct pci_dev *port = data->srv->port;
+	int rtsta_pos;
+	u32 rtsta;
+
+	rtsta_pos = pci_find_capability(port, PCI_CAP_ID_EXP) + PCI_EXP_RTSTA;
+
+	spin_lock_irq(&data->lock);
+
+	for (;;) {
+		if (data->noirq)
+			break;
+
+		pci_read_config_dword(port, rtsta_pos, &rtsta);
+		if (rtsta & PCI_EXP_RTSTA_PME) {
+			/*
+			 * Clear PME status of the port.  If there are other
+			 * pending PMEs, the status will be set again.
+			 */
+			pcie_pme_clear_status(port);
+
+			spin_unlock_irq(&data->lock);
+			pcie_pme_handle_request(port, rtsta & 0xffff);
+			spin_lock_irq(&data->lock);
+
+			continue;
+		}
+
+		/* No need to loop if there are no more PMEs pending. */
+		if (!(rtsta & PCI_EXP_RTSTA_PENDING))
+			break;
+
+		spin_unlock_irq(&data->lock);
+		cpu_relax();
+		spin_lock_irq(&data->lock);
+	}
+
+	if (!data->noirq)
+		pcie_pme_interrupt_enable(port, true);
+
+	spin_unlock_irq(&data->lock);
+}
+
+/**
+ * pcie_pme_irq - Interrupt handler for PCIe root port PME interrupt.
+ * @irq: Interrupt vector.
+ * @context: Interrupt context pointer.
+ */
+static irqreturn_t pcie_pme_irq(int irq, void *context)
+{
+	struct pci_dev *port;
+	struct pcie_pme_service_data *data;
+	int rtsta_pos;
+	u32 rtsta;
+	unsigned long flags;
+
+	port = ((struct pcie_device *)context)->port;
+	data = get_service_data((struct pcie_device *)context);
+
+	rtsta_pos = pci_find_capability(port, PCI_CAP_ID_EXP) + PCI_EXP_RTSTA;
+
+	spin_lock_irqsave(&data->lock, flags);
+	pci_read_config_dword(port, rtsta_pos, &rtsta);
+
+	if (!(rtsta & PCI_EXP_RTSTA_PME)) {
+		spin_unlock_irqrestore(&data->lock, flags);
+		return IRQ_NONE;
+	}
+
+	pcie_pme_interrupt_enable(port, false);
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	/* We don't use pm_wq, because it's freezable. */
+	schedule_work(&data->work);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * pcie_pme_set_native - Set the PME interrupt flag for given device.
+ * @dev: PCI device to handle.
+ * @ign: Ignored.
+ */
+static int pcie_pme_set_native(struct pci_dev *dev, void *ign)
+{
+	dev_info(&dev->dev, "Signaling PME through PCIe PME interrupt\n");
+
+	device_set_run_wake(&dev->dev, true);
+	dev->pme_interrupt = true;
+	return 0;
+}
+
+/**
+ * pcie_pme_mark_devices - Set the PME interrupt flag for devices below a port.
+ * @port: PCIe root port or event collector to handle.
+ *
+ * For each device below given root port, including the port itself (or for each
+ * root complex integrated endpoint if @port is a root complex event collector)
+ * set the flag indicating that it can signal run-time wake-up events via PCIe
+ * PME interrupts.
+ */
+static void pcie_pme_mark_devices(struct pci_dev *port)
+{
+	pcie_pme_set_native(port, NULL);
+	if (port->subordinate) {
+		pci_walk_bus(port->subordinate, pcie_pme_set_native, NULL);
+	} else {
+		struct pci_bus *bus = port->bus;
+		struct pci_dev *dev;
+
+		/* Check if this is a root port event collector. */
+		if (port->pcie_type != PCI_EXP_TYPE_RC_EC || !bus)
+			return;
+
+		down_read(&pci_bus_sem);
+		list_for_each_entry(dev, &bus->devices, bus_list)
+			if (dev->is_pcie
+			    && dev->pcie_type == PCI_EXP_TYPE_RC_END)
+				pcie_pme_set_native(dev, NULL);
+		up_read(&pci_bus_sem);
+	}
+}
+
+/**
+ * pcie_pme_probe - Initialize PCIe PME service for given root port.
+ * @srv: PCIe service to initialize.
+ */
+static int pcie_pme_probe(struct pcie_device *srv)
+{
+	struct pci_dev *port;
+	struct pcie_pme_service_data *data;
+	int ret;
+
+	if (!pcie_pme_platform_setup(srv))
+		return -EACCES;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	spin_lock_init(&data->lock);
+	INIT_WORK(&data->work, pcie_pme_work_fn);
+	data->srv = srv;
+	set_service_data(srv, data);
+
+	port = srv->port;
+	pcie_pme_interrupt_enable(port, false);
+	pcie_pme_clear_status(port);
+
+	ret = request_irq(srv->irq, pcie_pme_irq, IRQF_SHARED, "PCIe PME", srv);
+	if (ret) {
+		kfree(data);
+	} else {
+		pcie_pme_mark_devices(port);
+		pcie_pme_interrupt_enable(port, true);
+	}
+
+	return ret;
+}
+
+/**
+ * pcie_pme_suspend - Suspend PCIe PME service device.
+ * @srv: PCIe service device to suspend.
+ */
+static int pcie_pme_suspend(struct pcie_device *srv)
+{
+	struct pcie_pme_service_data *data = get_service_data(srv);
+	struct pci_dev *port = srv->port;
+
+	spin_lock_irq(&data->lock);
+	pcie_pme_interrupt_enable(port, false);
+	pcie_pme_clear_status(port);
+	data->noirq = true;
+	spin_unlock_irq(&data->lock);
+
+	synchronize_irq(srv->irq);
+
+	return 0;
+}
+
+/**
+ * pcie_pme_resume - Resume PCIe PME service device.
+ * @srv - PCIe service device to resume.
+ */
+static int pcie_pme_resume(struct pcie_device *srv)
+{
+	struct pcie_pme_service_data *data = get_service_data(srv);
+	struct pci_dev *port = srv->port;
+
+	spin_lock_irq(&data->lock);
+	data->noirq = false;
+	pcie_pme_clear_status(port);
+	pcie_pme_interrupt_enable(port, true);
+	spin_unlock_irq(&data->lock);
+
+	return 0;
+}
+
+/**
+ * pcie_pme_remove - Prepare PCIe PME service device for removal.
+ * @srv - PCIe service device to resume.
+ */
+static void pcie_pme_remove(struct pcie_device *srv)
+{
+	pcie_pme_suspend(srv);
+	free_irq(srv->irq, srv);
+	kfree(get_service_data(srv));
+}
+
+static struct pcie_port_service_driver pcie_pme_driver = {
+	.name		= "pcie_pme",
+	.port_type 	= PCI_EXP_TYPE_ROOT_PORT,
+	.service 	= PCIE_PORT_SERVICE_PME,
+
+	.probe		= pcie_pme_probe,
+	.suspend	= pcie_pme_suspend,
+	.resume		= pcie_pme_resume,
+	.remove		= pcie_pme_remove,
+};
+
+/**
+ * pcie_pme_service_init - Register the PCIe PME service driver.
+ */
+static int __init pcie_pme_service_init(void)
+{
+	return pcie_pme_disabled ?
+		-ENODEV : pcie_port_service_register(&pcie_pme_driver);
+}
+
+module_init(pcie_pme_service_init);
Index: linux-2.6/drivers/pci/pcie/pme/pcie_pme_acpi.c
===================================================================
--- /dev/null
+++ linux-2.6/drivers/pci/pcie/pme/pcie_pme_acpi.c
@@ -0,0 +1,54 @@
+/*
+ * PCIe Native PME support, ACPI-related part
+ *
+ * Copyright (C) 2009 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License V2.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/acpi.h>
+#include <linux/pci-acpi.h>
+#include <linux/pcieport_if.h>
+
+/**
+ * pcie_pme_acpi_setup - Request the ACPI BIOS to release control over PCIe PME.
+ * @srv - PCIe PME service for a root port or event collector.
+ *
+ * Invoked when the PCIe bus type loads PCIe PME service driver.  To avoid
+ * conflict with the BIOS PCIe support requires the BIOS to yield PCIe PME
+ * control to the kernel.
+ */
+int pcie_pme_acpi_setup(struct pcie_device *srv)
+{
+	acpi_status status = AE_NOT_FOUND;
+	struct pci_dev *port = srv->port;
+	acpi_handle handle;
+	int error = 0;
+
+	if (acpi_pci_disabled)
+		return -ENOSYS;
+
+	dev_info(&port->dev, "Requesting control of PCIe PME from ACPI BIOS\n");
+
+	handle = acpi_find_root_bridge_handle(port);
+	if (!handle)
+		return -EINVAL;
+
+	status = acpi_pci_osc_control_set(handle,
+			OSC_PCI_EXPRESS_PME_CONTROL |
+			OSC_PCI_EXPRESS_CAP_STRUCTURE_CONTROL);
+	if (ACPI_FAILURE(status)) {
+		dev_info(&port->dev,
+			"Failed to receive control of PCIe PME service: %s\n",
+			(status == AE_SUPPORT || status == AE_NOT_FOUND) ?
+			"no _OSC support" : "ACPI _OSC failed");
+		error = -ENODEV;
+	}
+
+	return error;
+}
Index: linux-2.6/drivers/pci/pcie/pme/Makefile
===================================================================
--- /dev/null
+++ linux-2.6/drivers/pci/pcie/pme/Makefile
@@ -0,0 +1,8 @@
+#
+# Makefile for PCI-Express Root Port PME signaling driver
+#
+
+obj-$(CONFIG_PCIE_PME) += pmedriver.o
+
+pmedriver-objs := pcie_pme.o
+pmedriver-$(CONFIG_ACPI) += pcie_pme_acpi.o
Index: linux-2.6/drivers/pci/pcie/pme/pcie_pme.h
===================================================================
--- /dev/null
+++ linux-2.6/drivers/pci/pcie/pme/pcie_pme.h
@@ -0,0 +1,28 @@
+/*
+ * drivers/pci/pcie/pme/pcie_pme.h
+ *
+ * PCI Express Root Port PME signaling support
+ *
+ * Copyright (C) 2009 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc.
+ */
+
+#ifndef _PCIE_PME_H_
+#define _PCIE_PME_H_
+
+struct pcie_device;
+
+#ifdef CONFIG_ACPI
+extern int pcie_pme_acpi_setup(struct pcie_device *srv);
+
+static inline int pcie_pme_platform_notify(struct pcie_device *srv)
+{
+	return pcie_pme_acpi_setup(srv);
+}
+#else /* !CONFIG_ACPI */
+static inline int pcie_pme_platform_notify(struct pcie_device *srv)
+{
+	return 0;
+}
+#endif /* !CONFIG_ACPI */
+
+#endif
Index: linux-2.6/include/linux/pci.h
===================================================================
--- linux-2.6.orig/include/linux/pci.h
+++ linux-2.6/include/linux/pci.h
@@ -239,6 +239,7 @@ struct pci_dev {
 					   configuration space */
 	unsigned int	pme_support:5;	/* Bitmask of states from which PME#
 					   can be generated */
+	unsigned int	pme_interrupt:1;
 	unsigned int	d1_support:1;	/* Low power state D1 is supported */
 	unsigned int	d2_support:1;	/* Low power state D2 is supported */
 	unsigned int	no_d1d2:1;	/* Only allow D0 and D3 */
Index: linux-2.6/Documentation/kernel-parameters.txt
===================================================================
--- linux-2.6.orig/Documentation/kernel-parameters.txt
+++ linux-2.6/Documentation/kernel-parameters.txt
@@ -1989,6 +1989,12 @@ and is between 256 and 4096 characters. 
 		force	Enable ASPM even on devices that claim not to support it.
 			WARNING: Forcing ASPM on may cause system lockups.
 
+	pcie_pme=	[PCIE,PM] Native PCIe PME signaling options:
+		off	Do not use native PCIe PME signaling.
+		force	Use native PCIe PME signaling even if the BIOS refuses
+			to allow the kernel to control the relevant PCIe config
+			registers.
+
 	pcmv=		[HW,PCMCIA] BadgePAD 4
 
 	pd.		[PARIDE]

Re: [PATCH 2/8] PCI PM: PCIe PME root port service driver (rev. 5)

[Kenji Kaneshige]

Hi,

I'm sorry for the delayed comments.

> +
> +/**
> + * pcie_pme_interrupt_enable - Enable/disable PCIe PME interrupt generation.
> + * @dev: PCIe root port or event collector.
> + * @enable: Enable or disable the interrupt.
> + */
> +static void pcie_pme_interrupt_enable(struct pci_dev *dev, bool enable)
> +{
> +	int rtctl_pos;
> +	u16 rtctl;
> +
> +	rtctl_pos = pci_find_capability(dev, PCI_CAP_ID_EXP) + PCI_EXP_RTCTL;

How about

	rtctl_pos = pci_pcie_cap(dev) + PCI_EXP_RTCTL;

?

The pci_pcie_cap() returns PCIe capability offset saved in struct pci_dev.
By using this, we can avoid redundant search in PCI configuration space.

> +
> +/**
> + * pcie_pme_clear_status - Clear root port PME interrupt status.
> + * @dev: PCIe root port or event collector.
> + */
> +static void pcie_pme_clear_status(struct pci_dev *dev)
> +{
> +	int rtsta_pos;
> +	u32 rtsta;
> +
> +	rtsta_pos = pci_find_capability(dev, PCI_CAP_ID_EXP) + PCI_EXP_RTSTA;

Ditto.


> +/**
> + * pcie_pme_work_fn - Work handler for PCIe PME interrupt.
> + * @work: Work structure giving access to service data.
> + */
> +static void pcie_pme_work_fn(struct work_struct *work)
> +{
> +	struct pcie_pme_service_data *data =
> +			container_of(work, struct pcie_pme_service_data, work);
> +	struct pci_dev *port = data->srv->port;
> +	int rtsta_pos;
> +	u32 rtsta;
> +
> +	rtsta_pos = pci_find_capability(port, PCI_CAP_ID_EXP) + PCI_EXP_RTSTA;

Ditto.


> +/**
> + * pcie_pme_irq - Interrupt handler for PCIe root port PME interrupt.
> + * @irq: Interrupt vector.
> + * @context: Interrupt context pointer.
> + */
> +static irqreturn_t pcie_pme_irq(int irq, void *context)
> +{
> +	struct pci_dev *port;
> +	struct pcie_pme_service_data *data;
> +	int rtsta_pos;
> +	u32 rtsta;
> +	unsigned long flags;
> +
> +	port = ((struct pcie_device *)context)->port;
> +	data = get_service_data((struct pcie_device *)context);
> +
> +	rtsta_pos = pci_find_capability(port, PCI_CAP_ID_EXP) + PCI_EXP_RTSTA;

Ditto.


Thanks,
Kenji Kaneshige

Re: [PATCH 2/8] PCI PM: PCIe PME root port service driver (rev. 5)

[Rafael J. Wysocki]

On Thursday 18 February 2010, Kenji Kaneshige wrote:
> Hi,
> 
> I'm sorry for the delayed comments.
> 
> > +
> > +/**
> > + * pcie_pme_interrupt_enable - Enable/disable PCIe PME interrupt generation.
> > + * @dev: PCIe root port or event collector.
> > + * @enable: Enable or disable the interrupt.
> > + */
> > +static void pcie_pme_interrupt_enable(struct pci_dev *dev, bool enable)
> > +{
> > +	int rtctl_pos;
> > +	u16 rtctl;
> > +
> > +	rtctl_pos = pci_find_capability(dev, PCI_CAP_ID_EXP) + PCI_EXP_RTCTL;
> 
> How about
> 
> 	rtctl_pos = pci_pcie_cap(dev) + PCI_EXP_RTCTL;
> 
> ?
> 
> The pci_pcie_cap() returns PCIe capability offset saved in struct pci_dev.
> By using this, we can avoid redundant search in PCI configuration space.

While I agree with the comment, I'd prefer to change this with a separate
patch, unless the entire patchset misses the merge window.

Rafael

Re: [PATCH 2/8] PCI PM: PCIe PME root port service driver (rev. 5)

[Kenji Kaneshige]

Rafael J. Wysocki wrote:
> On Thursday 18 February 2010, Kenji Kaneshige wrote:
>> Hi,
>>
>> I'm sorry for the delayed comments.
>>
>>> +
>>> +/**
>>> + * pcie_pme_interrupt_enable - Enable/disable PCIe PME interrupt generation.
>>> + * @dev: PCIe root port or event collector.
>>> + * @enable: Enable or disable the interrupt.
>>> + */
>>> +static void pcie_pme_interrupt_enable(struct pci_dev *dev, bool enable)
>>> +{
>>> +	int rtctl_pos;
>>> +	u16 rtctl;
>>> +
>>> +	rtctl_pos = pci_find_capability(dev, PCI_CAP_ID_EXP) + PCI_EXP_RTCTL;
>> How about
>>
>> 	rtctl_pos = pci_pcie_cap(dev) + PCI_EXP_RTCTL;
>>
>> ?
>>
>> The pci_pcie_cap() returns PCIe capability offset saved in struct pci_dev.
>> By using this, we can avoid redundant search in PCI configuration space.
> 
> While I agree with the comment, I'd prefer to change this with a separate
> patch, unless the entire patchset misses the merge window.
> 

Ok. Actually, I didn't realize your set of patches was already in
linux-next, sorry. I'll send a patch as a separate one.

Thanks,
Kenji Kaneshige

[PATCH 3/8] PCI PM: Make it possible to force using INTx for PCIe PME signaling

[Rafael J. Wysocki]

From: Rafael J. Wysocki <rjw@sisk.pl>

Apparently, some machines may have problems with PCI run-time power
management if MSIs are used for the native PCIe PME signaling.  In
particular, on the MSI Wind U-100 PCIe PME interrupts are not
generated by a PCIe root port after a resume from suspend to RAM, if
the system wake-up was triggered by a PME from the device attached to
this port.  [It doesn't help to free the interrupt on suspend and
request it back on resume, even if that is done along with disabling
the MSI and re-enabling it, respectively.]  However, if INTx
interrupts are used for this purpose on the same machine, everything
works just fine.

For this reason, add a kernel command line switch allowing one to
request that MSIs be not used for the native PCIe PME signaling,
introduce a DMI table allowing us to blacklist machines that need
this switch to be set by default and put the MSI Wind U-100 into this
table.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 Documentation/kernel-parameters.txt |    2 ++
 drivers/pci/pcie/pme/pcie_pme.c     |   14 +++++++++++++-
 drivers/pci/pcie/portdrv.h          |   17 +++++++++++++++++
 drivers/pci/pcie/portdrv_core.c     |   12 ++++++++++--
 drivers/pci/pcie/portdrv_pci.c      |   27 +++++++++++++++++++++++++++
 5 files changed, 69 insertions(+), 3 deletions(-)

Index: linux-2.6/drivers/pci/pcie/pme/pcie_pme.c
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/pme/pcie_pme.c
+++ linux-2.6/drivers/pci/pcie/pme/pcie_pme.c
@@ -53,12 +53,22 @@ static bool pcie_pme_disabled;
  */
 static bool pcie_pme_force_enable;
 
+/*
+ * If this switch is set, MSI will not be used for PCIe PME signaling.  This
+ * causes the PCIe port driver to use INTx interrupts only, but it turns out
+ * that using MSI for PCIe PME signaling doesn't play well with PCIe PME-based
+ * wake-up from system sleep states.
+ */
+bool pcie_pme_msi_disabled;
+
 static int __init pcie_pme_setup(char *str)
 {
 	if (!strcmp(str, "off"))
 		pcie_pme_disabled = true;
 	else if (!strcmp(str, "force"))
 		pcie_pme_force_enable = true;
+	else if (!strcmp(str, "nomsi"))
+		pcie_pme_msi_disabled = true;
 	return 1;
 }
 __setup("pcie_pme=", pcie_pme_setup);
@@ -73,7 +83,9 @@ __setup("pcie_pme=", pcie_pme_setup);
  */
 static bool pcie_pme_platform_setup(struct pcie_device *srv)
 {
-	return !pcie_pme_platform_notify(srv) || pcie_pme_force_enable;
+	if (!pcie_pme_platform_notify(srv))
+		return true;
+	return pcie_pme_force_enable;
 }
 
 struct pcie_pme_service_data {
Index: linux-2.6/drivers/pci/pcie/portdrv_core.c
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/portdrv_core.c
+++ linux-2.6/drivers/pci/pcie/portdrv_core.c
@@ -186,16 +186,24 @@ static int pcie_port_enable_msix(struct 
  */
 static int init_service_irqs(struct pci_dev *dev, int *irqs, int mask)
 {
-	int i, irq;
+	int i, irq = -1;
+
+	/* We have to use INTx if MSI cannot be used for PCIe PME. */
+	if ((mask & PCIE_PORT_SERVICE_PME) && pcie_pme_no_msi()) {
+		if (dev->pin)
+			irq = dev->irq;
+		goto no_msi;
+	}
 
 	/* Try to use MSI-X if supported */
 	if (!pcie_port_enable_msix(dev, irqs, mask))
 		return 0;
+
 	/* We're not going to use MSI-X, so try MSI and fall back to INTx */
-	irq = -1;
 	if (!pci_enable_msi(dev) || dev->pin)
 		irq = dev->irq;
 
+ no_msi:
 	for (i = 0; i < PCIE_PORT_DEVICE_MAXSERVICES; i++)
 		irqs[i] = irq;
 	irqs[PCIE_PORT_SERVICE_VC_SHIFT] = -1;
Index: linux-2.6/drivers/pci/pcie/portdrv_pci.c
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/portdrv_pci.c
+++ linux-2.6/drivers/pci/pcie/portdrv_pci.c
@@ -15,6 +15,7 @@
 #include <linux/slab.h>
 #include <linux/pcieport_if.h>
 #include <linux/aer.h>
+#include <linux/dmi.h>
 
 #include "portdrv.h"
 #include "aer/aerdrv.h"
@@ -273,10 +274,36 @@ static struct pci_driver pcie_portdriver
 	.driver.pm 	= PCIE_PORTDRV_PM_OPS,
 };
 
+static int __init dmi_pcie_pme_disable_msi(const struct dmi_system_id *d)
+{
+	pr_notice("%s detected: will not use MSI for PCIe PME signaling\n",
+			d->ident);
+	pcie_pme_disable_msi();
+	return 0;
+}
+
+static struct dmi_system_id __initdata pcie_portdrv_dmi_table[] = {
+	/*
+	 * Boxes that should not use MSI for PCIe PME signaling.
+	 */
+	{
+	 .callback = dmi_pcie_pme_disable_msi,
+	 .ident = "MSI Wind U-100",
+	 .matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR,
+		     		"MICRO-STAR INTERNATIONAL CO., LTD"),
+		     DMI_MATCH(DMI_PRODUCT_NAME, "U-100"),
+		     },
+	 },
+	 {}
+};
+
 static int __init pcie_portdrv_init(void)
 {
 	int retval;
 
+	dmi_check_system(pcie_portdrv_dmi_table);
+
 	retval = pcie_port_bus_register();
 	if (retval) {
 		printk(KERN_WARNING "PCIE: bus_register error: %d\n", retval);
Index: linux-2.6/drivers/pci/pcie/portdrv.h
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/portdrv.h
+++ linux-2.6/drivers/pci/pcie/portdrv.h
@@ -30,4 +30,21 @@ extern void pcie_port_device_remove(stru
 extern int __must_check pcie_port_bus_register(void);
 extern void pcie_port_bus_unregister(void);
 
+#ifdef CONFIG_PCIE_PME
+extern bool pcie_pme_msi_disabled;
+
+static inline void pcie_pme_disable_msi(void)
+{
+	pcie_pme_msi_disabled = true;
+}
+
+static inline bool pcie_pme_no_msi(void)
+{
+	return pcie_pme_msi_disabled;
+}
+#else /* !CONFIG_PCIE_PME */
+static inline void pcie_pme_disable_msi(void) {}
+static inline bool pcie_pme_no_msi(void) { return false; }
+#endif /* !CONFIG_PCIE_PME */
+
 #endif /* _PORTDRV_H_ */
Index: linux-2.6/Documentation/kernel-parameters.txt
===================================================================
--- linux-2.6.orig/Documentation/kernel-parameters.txt
+++ linux-2.6/Documentation/kernel-parameters.txt
@@ -1994,6 +1994,8 @@ and is between 256 and 4096 characters. 
 		force	Use native PCIe PME signaling even if the BIOS refuses
 			to allow the kernel to control the relevant PCIe config
 			registers.
+		nomsi	Do not use MSI for native PCIe PME signaling (this makes
+			all PCIe root ports use INTx for everything).
 
 	pcmv=		[HW,PCMCIA] BadgePAD 4
 

[PATCH 4/8] ACPI: Use GPE reference counting to support shared GPEs

[Rafael J. Wysocki]

From: Rafael J. Wysocki <rjw@sisk.pl>

ACPI GPEs may map to multiple devices.  The current GPE interface
only provides a mechanism for enabling and disabling GPEs, making
it difficult to change the state of GPEs at runtime without extensive
cooperation between devices.

Add an API to allow devices to indicate whether or not they want
their device's GPE to be enabled for both runtime and wakeup events.

Remove the old GPE type handling entirely, which gets rid of various
quirks, like the implicit disabling with GPE type setting. This
requires a small amount of rework in order to ensure that non-wake
GPEs are enabled by default to preserve existing behaviour.

Based on patches from Matthew Garrett <mjg@redhat.com>.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 drivers/acpi/acpica/acevents.h |    6 -
 drivers/acpi/acpica/aclocal.h  |    2 
 drivers/acpi/acpica/evgpe.c    |  153 ++++-------------------------------------
 drivers/acpi/acpica/evgpeblk.c |   87 ++++++++---------------
 drivers/acpi/acpica/evxface.c  |   14 ---
 drivers/acpi/acpica/evxfevnt.c |   90 +++++++++++++++++-------
 drivers/acpi/button.c          |   13 ++-
 drivers/acpi/ec.c              |   14 ++-
 drivers/acpi/sleep.c           |   15 +++-
 drivers/acpi/system.c          |    4 -
 drivers/acpi/wakeup.c          |   81 +++++++--------------
 include/acpi/acpixf.h          |    6 -
 include/acpi/actypes.h         |   28 ++-----
 13 files changed, 188 insertions(+), 325 deletions(-)

Index: linux-2.6/drivers/acpi/acpica/aclocal.h
===================================================================
--- linux-2.6.orig/drivers/acpi/acpica/aclocal.h
+++ linux-2.6/drivers/acpi/acpica/aclocal.h
@@ -426,6 +426,8 @@ struct acpi_gpe_event_info {
 	struct acpi_gpe_register_info *register_info;	/* Backpointer to register info */
 	u8 flags;		/* Misc info about this GPE */
 	u8 gpe_number;		/* This GPE */
+	u8 runtime_count;
+	u8 wakeup_count;
 };
 
 /* Information about a GPE register pair, one per each status/enable pair in an array */
Index: linux-2.6/drivers/acpi/acpica/evxfevnt.c
===================================================================
--- linux-2.6.orig/drivers/acpi/acpica/evxfevnt.c
+++ linux-2.6/drivers/acpi/acpica/evxfevnt.c
@@ -201,23 +201,27 @@ ACPI_EXPORT_SYMBOL(acpi_enable_event)
 
 /*******************************************************************************
  *
- * FUNCTION:    acpi_set_gpe_type
+ * FUNCTION:    acpi_set_gpe
  *
  * PARAMETERS:  gpe_device      - Parent GPE Device
  *              gpe_number      - GPE level within the GPE block
- *              Type            - New GPE type
+ *              action          - Enable or disable
+ *                                Called from ISR or not
  *
  * RETURN:      Status
  *
- * DESCRIPTION: Set the type of an individual GPE
+ * DESCRIPTION: Enable or disable an ACPI event (general purpose)
  *
  ******************************************************************************/
-acpi_status acpi_set_gpe_type(acpi_handle gpe_device, u32 gpe_number, u8 type)
+acpi_status acpi_set_gpe(acpi_handle gpe_device, u32 gpe_number, u8 action)
 {
 	acpi_status status = AE_OK;
+	acpi_cpu_flags flags;
 	struct acpi_gpe_event_info *gpe_event_info;
 
-	ACPI_FUNCTION_TRACE(acpi_set_gpe_type);
+	ACPI_FUNCTION_TRACE(acpi_set_gpe);
+
+	flags = acpi_os_acquire_lock(acpi_gbl_gpe_lock);
 
 	/* Ensure that we have a valid GPE number */
 
@@ -227,19 +231,29 @@ acpi_status acpi_set_gpe_type(acpi_handl
 		goto unlock_and_exit;
 	}
 
-	if ((gpe_event_info->flags & ACPI_GPE_TYPE_MASK) == type) {
-		return_ACPI_STATUS(AE_OK);
-	}
+	/* Perform the action */
 
-	/* Set the new type (will disable GPE if currently enabled) */
+	switch (action) {
+	case ACPI_GPE_ENABLE:
+		status = acpi_ev_enable_gpe(gpe_event_info, TRUE);
+		break;
+
+	case ACPI_GPE_DISABLE:
+		status = acpi_ev_disable_gpe(gpe_event_info);
+		break;
 
-	status = acpi_ev_set_gpe_type(gpe_event_info, type);
+	default:
+		ACPI_ERROR((AE_INFO, "Invalid action\n"));
+		status = AE_BAD_PARAMETER;
+		break;
+	}
 
       unlock_and_exit:
+	acpi_os_release_lock(acpi_gbl_gpe_lock, flags);
 	return_ACPI_STATUS(status);
 }
 
-ACPI_EXPORT_SYMBOL(acpi_set_gpe_type)
+ACPI_EXPORT_SYMBOL(acpi_set_gpe)
 
 /*******************************************************************************
  *
@@ -247,15 +261,14 @@ ACPI_EXPORT_SYMBOL(acpi_set_gpe_type)
  *
  * PARAMETERS:  gpe_device      - Parent GPE Device
  *              gpe_number      - GPE level within the GPE block
- *              Flags           - Just enable, or also wake enable?
- *                                Called from ISR or not
+ *              type            - Purpose the GPE will be used for
  *
  * RETURN:      Status
  *
- * DESCRIPTION: Enable an ACPI event (general purpose)
+ * DESCRIPTION: Take a reference to a GPE and enable it if necessary
  *
  ******************************************************************************/
-acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number)
+acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number, u8 type)
 {
 	acpi_status status = AE_OK;
 	acpi_cpu_flags flags;
@@ -273,15 +286,32 @@ acpi_status acpi_enable_gpe(acpi_handle 
 		goto unlock_and_exit;
 	}
 
-	/* Perform the enable */
+	if (type & ACPI_GPE_TYPE_RUNTIME) {
+		if (++gpe_event_info->runtime_count == 1)
+			status = acpi_ev_enable_gpe(gpe_event_info, TRUE);
 
-	status = acpi_ev_enable_gpe(gpe_event_info, TRUE);
+		if (ACPI_FAILURE(status))
+			gpe_event_info->runtime_count--;
+	}
 
-      unlock_and_exit:
+	if (type & ACPI_GPE_TYPE_WAKE) {
+		if (!(gpe_event_info->flags & ACPI_GPE_CAN_WAKE)) {
+			status = AE_BAD_PARAMETER;
+			goto unlock_and_exit;
+		}
+
+		/*
+		 * Wake-up GPEs are only enabled right prior to putting the
+		 * system into a sleep state.
+		 */
+		if (++gpe_event_info->wakeup_count == 1)
+			acpi_ev_update_gpe_enable_masks(gpe_event_info);
+	}
+
+unlock_and_exit:
 	acpi_os_release_lock(acpi_gbl_gpe_lock, flags);
 	return_ACPI_STATUS(status);
 }
-
 ACPI_EXPORT_SYMBOL(acpi_enable_gpe)
 
 /*******************************************************************************
@@ -290,15 +320,14 @@ ACPI_EXPORT_SYMBOL(acpi_enable_gpe)
  *
  * PARAMETERS:  gpe_device      - Parent GPE Device
  *              gpe_number      - GPE level within the GPE block
- *              Flags           - Just disable, or also wake disable?
- *                                Called from ISR or not
+ *              type            - Purpose the GPE won't be used for any more
  *
  * RETURN:      Status
  *
- * DESCRIPTION: Disable an ACPI event (general purpose)
+ * DESCRIPTION: Release a reference to a GPE and disable it if necessary
  *
  ******************************************************************************/
-acpi_status acpi_disable_gpe(acpi_handle gpe_device, u32 gpe_number)
+acpi_status acpi_disable_gpe(acpi_handle gpe_device, u32 gpe_number, u8 type)
 {
 	acpi_status status = AE_OK;
 	acpi_cpu_flags flags;
@@ -315,13 +344,24 @@ acpi_status acpi_disable_gpe(acpi_handle
 		goto unlock_and_exit;
 	}
 
-	status = acpi_ev_disable_gpe(gpe_event_info);
+	if ((type & ACPI_GPE_TYPE_WAKE) && gpe_event_info->runtime_count) {
+		if (--gpe_event_info->runtime_count == 0)
+			acpi_ev_disable_gpe(gpe_event_info);
+	}
+
+	if ((type & ACPI_GPE_TYPE_RUNTIME) && gpe_event_info->wakeup_count) {
+		/*
+		 * Wake-up GPEs are not enabled after leaving system sleep
+		 * states, so we don't need to disable them here.
+		 */
+		if (--gpe_event_info->wakeup_count == 0)
+			acpi_ev_update_gpe_enable_masks(gpe_event_info);
+	}
 
 unlock_and_exit:
 	acpi_os_release_lock(acpi_gbl_gpe_lock, flags);
 	return_ACPI_STATUS(status);
 }
-
 ACPI_EXPORT_SYMBOL(acpi_disable_gpe)
 
 /*******************************************************************************
Index: linux-2.6/include/acpi/acpixf.h
===================================================================
--- linux-2.6.orig/include/acpi/acpixf.h
+++ linux-2.6/include/acpi/acpixf.h
@@ -281,11 +281,11 @@ acpi_status acpi_get_event_status(u32 ev
 /*
  * GPE Interfaces
  */
-acpi_status acpi_set_gpe_type(acpi_handle gpe_device, u32 gpe_number, u8 type);
+acpi_status acpi_set_gpe(acpi_handle gpe_device, u32 gpe_number, u8 action);
 
-acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number);
+acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number, u8 type);
 
-acpi_status acpi_disable_gpe(acpi_handle gpe_device, u32 gpe_number);
+acpi_status acpi_disable_gpe(acpi_handle gpe_device, u32 gpe_number, u8 type);
 
 acpi_status acpi_clear_gpe(acpi_handle gpe_device, u32 gpe_number, u32 flags);
 
Index: linux-2.6/drivers/acpi/button.c
===================================================================
--- linux-2.6.orig/drivers/acpi/button.c
+++ linux-2.6/drivers/acpi/button.c
@@ -422,11 +422,9 @@ static int acpi_button_add(struct acpi_d
 
 	if (device->wakeup.flags.valid) {
 		/* Button's GPE is run-wake GPE */
-		acpi_set_gpe_type(device->wakeup.gpe_device,
-				  device->wakeup.gpe_number,
-				  ACPI_GPE_TYPE_WAKE_RUN);
 		acpi_enable_gpe(device->wakeup.gpe_device,
-				device->wakeup.gpe_number);
+				device->wakeup.gpe_number,
+				ACPI_GPE_TYPE_WAKE_RUN);
 		device->wakeup.state.enabled = 1;
 	}
 
@@ -446,6 +444,13 @@ static int acpi_button_remove(struct acp
 {
 	struct acpi_button *button = acpi_driver_data(device);
 
+	if (device->wakeup.flags.valid) {
+		acpi_disable_gpe(device->wakeup.gpe_device,
+				device->wakeup.gpe_number,
+				ACPI_GPE_TYPE_WAKE_RUN);
+		device->wakeup.state.enabled = 0;
+	}
+
 	acpi_button_remove_fs(device);
 	input_unregister_device(button->input);
 	kfree(button);
Index: linux-2.6/drivers/acpi/ec.c
===================================================================
--- linux-2.6.orig/drivers/acpi/ec.c
+++ linux-2.6/drivers/acpi/ec.c
@@ -307,7 +307,7 @@ static int acpi_ec_transaction(struct ac
 	pr_debug(PREFIX "transaction start\n");
 	/* disable GPE during transaction if storm is detected */
 	if (test_bit(EC_FLAGS_GPE_STORM, &ec->flags)) {
-		acpi_disable_gpe(NULL, ec->gpe);
+		acpi_set_gpe(NULL, ec->gpe, ACPI_GPE_DISABLE);
 	}
 
 	status = acpi_ec_transaction_unlocked(ec, t);
@@ -317,7 +317,7 @@ static int acpi_ec_transaction(struct ac
 	if (test_bit(EC_FLAGS_GPE_STORM, &ec->flags)) {
 		msleep(1);
 		/* it is safe to enable GPE outside of transaction */
-		acpi_enable_gpe(NULL, ec->gpe);
+		acpi_set_gpe(NULL, ec->gpe, ACPI_GPE_ENABLE);
 	} else if (t->irq_count > ACPI_EC_STORM_THRESHOLD) {
 		pr_info(PREFIX "GPE storm detected, "
 			"transactions will use polling mode\n");
@@ -788,8 +788,8 @@ static int ec_install_handlers(struct ac
 				  &acpi_ec_gpe_handler, ec);
 	if (ACPI_FAILURE(status))
 		return -ENODEV;
-	acpi_set_gpe_type(NULL, ec->gpe, ACPI_GPE_TYPE_RUNTIME);
-	acpi_enable_gpe(NULL, ec->gpe);
+
+	acpi_enable_gpe(NULL, ec->gpe, ACPI_GPE_TYPE_RUNTIME);
 	status = acpi_install_address_space_handler(ec->handle,
 						    ACPI_ADR_SPACE_EC,
 						    &acpi_ec_space_handler,
@@ -806,6 +806,7 @@ static int ec_install_handlers(struct ac
 		} else {
 			acpi_remove_gpe_handler(NULL, ec->gpe,
 				&acpi_ec_gpe_handler);
+			acpi_disable_gpe(NULL, ec->gpe, ACPI_GPE_TYPE_RUNTIME);
 			return -ENODEV;
 		}
 	}
@@ -816,6 +817,7 @@ static int ec_install_handlers(struct ac
 
 static void ec_remove_handlers(struct acpi_ec *ec)
 {
+	acpi_disable_gpe(NULL, ec->gpe, ACPI_GPE_TYPE_RUNTIME);
 	if (ACPI_FAILURE(acpi_remove_address_space_handler(ec->handle,
 				ACPI_ADR_SPACE_EC, &acpi_ec_space_handler)))
 		pr_err(PREFIX "failed to remove space handler\n");
@@ -1058,7 +1060,7 @@ static int acpi_ec_suspend(struct acpi_d
 {
 	struct acpi_ec *ec = acpi_driver_data(device);
 	/* Stop using GPE */
-	acpi_disable_gpe(NULL, ec->gpe);
+	acpi_set_gpe(NULL, ec->gpe, ACPI_GPE_DISABLE);
 	return 0;
 }
 
@@ -1066,7 +1068,7 @@ static int acpi_ec_resume(struct acpi_de
 {
 	struct acpi_ec *ec = acpi_driver_data(device);
 	/* Enable use of GPE back */
-	acpi_enable_gpe(NULL, ec->gpe);
+	acpi_set_gpe(NULL, ec->gpe, ACPI_GPE_ENABLE);
 	return 0;
 }
 
Index: linux-2.6/drivers/acpi/sleep.c
===================================================================
--- linux-2.6.orig/drivers/acpi/sleep.c
+++ linux-2.6/drivers/acpi/sleep.c
@@ -745,9 +745,18 @@ int acpi_pm_device_sleep_wake(struct dev
 		return -ENODEV;
 	}
 
-	error = enable ?
-		acpi_enable_wakeup_device_power(adev, acpi_target_sleep_state) :
-		acpi_disable_wakeup_device_power(adev);
+	if (enable) {
+		error = acpi_enable_wakeup_device_power(adev,
+						acpi_target_sleep_state);
+		if (!error)
+			acpi_enable_gpe(adev->wakeup.gpe_device,
+					adev->wakeup.gpe_number,
+					ACPI_GPE_TYPE_WAKE);
+	} else {
+		acpi_disable_gpe(adev->wakeup.gpe_device, adev->wakeup.gpe_number,
+				ACPI_GPE_TYPE_WAKE);
+		error = acpi_disable_wakeup_device_power(adev);
+	}
 	if (!error)
 		dev_info(dev, "wake-up capability %s by ACPI\n",
 				enable ? "enabled" : "disabled");
Index: linux-2.6/drivers/acpi/wakeup.c
===================================================================
--- linux-2.6.orig/drivers/acpi/wakeup.c
+++ linux-2.6/drivers/acpi/wakeup.c
@@ -21,12 +21,12 @@
 ACPI_MODULE_NAME("wakeup_devices")
 
 /**
- * acpi_enable_wakeup_device_prep - prepare wakeup devices
- *	@sleep_state:	ACPI state
- * Enable all wakup devices power if the devices' wakeup level
- * is higher than requested sleep level
+ * acpi_enable_wakeup_device_prep - Prepare wake-up devices.
+ * @sleep_state: ACPI system sleep state.
+ *
+ * Enable all wake-up devices' power, unless the requested system sleep state is
+ * too deep.
  */
-
 void acpi_enable_wakeup_device_prep(u8 sleep_state)
 {
 	struct list_head *node, *next;
@@ -36,9 +36,8 @@ void acpi_enable_wakeup_device_prep(u8 s
 						       struct acpi_device,
 						       wakeup_list);
 
-		if (!dev->wakeup.flags.valid ||
-		    !dev->wakeup.state.enabled ||
-		    (sleep_state > (u32) dev->wakeup.sleep_state))
+		if (!dev->wakeup.flags.valid || !dev->wakeup.state.enabled
+		    || (sleep_state > (u32) dev->wakeup.sleep_state))
 			continue;
 
 		acpi_enable_wakeup_device_power(dev, sleep_state);
@@ -46,9 +45,12 @@ void acpi_enable_wakeup_device_prep(u8 s
 }
 
 /**
- * acpi_enable_wakeup_device - enable wakeup devices
- *	@sleep_state:	ACPI state
- * Enable all wakup devices's GPE
+ * acpi_enable_wakeup_device - Enable wake-up device GPEs.
+ * @sleep_state: ACPI system sleep state.
+ *
+ * Enable all wake-up devices' GPEs, with the assumption that
+ * acpi_disable_all_gpes() was executed before, so we don't need to disable any
+ * GPEs here.
  */
 void acpi_enable_wakeup_device(u8 sleep_state)
 {
@@ -65,29 +67,22 @@ void acpi_enable_wakeup_device(u8 sleep_
 		if (!dev->wakeup.flags.valid)
 			continue;
 
-		/* If users want to disable run-wake GPE,
-		 * we only disable it for wake and leave it for runtime
-		 */
 		if ((!dev->wakeup.state.enabled && !dev->wakeup.prepare_count)
-		    || sleep_state > (u32) dev->wakeup.sleep_state) {
-			if (dev->wakeup.flags.run_wake) {
-				/* set_gpe_type will disable GPE, leave it like that */
-				acpi_set_gpe_type(dev->wakeup.gpe_device,
-						  dev->wakeup.gpe_number,
-						  ACPI_GPE_TYPE_RUNTIME);
-			}
+		    || sleep_state > (u32) dev->wakeup.sleep_state)
 			continue;
-		}
-		if (!dev->wakeup.flags.run_wake)
-			acpi_enable_gpe(dev->wakeup.gpe_device,
-					dev->wakeup.gpe_number);
+
+		/* The wake-up power should have been enabled already. */
+		acpi_set_gpe(dev->wakeup.gpe_device, dev->wakeup.gpe_number,
+				ACPI_GPE_ENABLE);
 	}
 }
 
 /**
- * acpi_disable_wakeup_device - disable devices' wakeup capability
- *	@sleep_state:	ACPI state
- * Disable all wakup devices's GPE and wakeup capability
+ * acpi_disable_wakeup_device - Disable devices' wakeup capability.
+ * @sleep_state: ACPI system sleep state.
+ *
+ * This function only affects devices with wakeup.state.enabled set, which means
+ * that it reverses the changes made by acpi_enable_wakeup_device_prep().
  */
 void acpi_disable_wakeup_device(u8 sleep_state)
 {
@@ -97,30 +92,11 @@ void acpi_disable_wakeup_device(u8 sleep
 		struct acpi_device *dev =
 			container_of(node, struct acpi_device, wakeup_list);
 
-		if (!dev->wakeup.flags.valid)
-			continue;
-
-		if ((!dev->wakeup.state.enabled && !dev->wakeup.prepare_count)
-		    || sleep_state > (u32) dev->wakeup.sleep_state) {
-			if (dev->wakeup.flags.run_wake) {
-				acpi_set_gpe_type(dev->wakeup.gpe_device,
-						  dev->wakeup.gpe_number,
-						  ACPI_GPE_TYPE_WAKE_RUN);
-				/* Re-enable it, since set_gpe_type will disable it */
-				acpi_enable_gpe(dev->wakeup.gpe_device,
-						dev->wakeup.gpe_number);
-			}
+		if (!dev->wakeup.flags.valid || !dev->wakeup.state.enabled
+		    || (sleep_state > (u32) dev->wakeup.sleep_state))
 			continue;
-		}
 
 		acpi_disable_wakeup_device_power(dev);
-		/* Never disable run-wake GPE */
-		if (!dev->wakeup.flags.run_wake) {
-			acpi_disable_gpe(dev->wakeup.gpe_device,
-					 dev->wakeup.gpe_number);
-			acpi_clear_gpe(dev->wakeup.gpe_device,
-				       dev->wakeup.gpe_number, ACPI_NOT_ISR);
-		}
 	}
 }
 
@@ -136,11 +112,8 @@ int __init acpi_wakeup_device_init(void)
 		/* In case user doesn't load button driver */
 		if (!dev->wakeup.flags.run_wake || dev->wakeup.state.enabled)
 			continue;
-		acpi_set_gpe_type(dev->wakeup.gpe_device,
-				  dev->wakeup.gpe_number,
-				  ACPI_GPE_TYPE_WAKE_RUN);
-		acpi_enable_gpe(dev->wakeup.gpe_device,
-				dev->wakeup.gpe_number);
+ 		acpi_enable_gpe(dev->wakeup.gpe_device, dev->wakeup.gpe_number,
+ 				ACPI_GPE_TYPE_WAKE);
 		dev->wakeup.state.enabled = 1;
 	}
 	mutex_unlock(&acpi_device_lock);
Index: linux-2.6/drivers/acpi/acpica/acevents.h
===================================================================
--- linux-2.6.orig/drivers/acpi/acpica/acevents.h
+++ linux-2.6/drivers/acpi/acpica/acevents.h
@@ -76,8 +76,7 @@ acpi_ev_queue_notify_request(struct acpi
  * evgpe - GPE handling and dispatch
  */
 acpi_status
-acpi_ev_update_gpe_enable_masks(struct acpi_gpe_event_info *gpe_event_info,
-				u8 type);
+acpi_ev_update_gpe_enable_masks(struct acpi_gpe_event_info *gpe_event_info);
 
 acpi_status
 acpi_ev_enable_gpe(struct acpi_gpe_event_info *gpe_event_info,
@@ -122,9 +121,6 @@ acpi_ev_gpe_dispatch(struct acpi_gpe_eve
 u32 acpi_ev_gpe_detect(struct acpi_gpe_xrupt_info *gpe_xrupt_list);
 
 acpi_status
-acpi_ev_set_gpe_type(struct acpi_gpe_event_info *gpe_event_info, u8 type);
-
-acpi_status
 acpi_ev_check_for_wake_only_gpe(struct acpi_gpe_event_info *gpe_event_info);
 
 acpi_status acpi_ev_gpe_initialize(void);
Index: linux-2.6/drivers/acpi/acpica/evgpe.c
===================================================================
--- linux-2.6.orig/drivers/acpi/acpica/evgpe.c
+++ linux-2.6/drivers/acpi/acpica/evgpe.c
@@ -54,54 +54,9 @@ static void ACPI_SYSTEM_XFACE acpi_ev_as
 
 /*******************************************************************************
  *
- * FUNCTION:    acpi_ev_set_gpe_type
- *
- * PARAMETERS:  gpe_event_info          - GPE to set
- *              Type                    - New type
- *
- * RETURN:      Status
- *
- * DESCRIPTION: Sets the new type for the GPE (wake, run, or wake/run)
- *
- ******************************************************************************/
-
-acpi_status
-acpi_ev_set_gpe_type(struct acpi_gpe_event_info *gpe_event_info, u8 type)
-{
-	acpi_status status;
-
-	ACPI_FUNCTION_TRACE(ev_set_gpe_type);
-
-	/* Validate type and update register enable masks */
-
-	switch (type) {
-	case ACPI_GPE_TYPE_WAKE:
-	case ACPI_GPE_TYPE_RUNTIME:
-	case ACPI_GPE_TYPE_WAKE_RUN:
-		break;
-
-	default:
-		return_ACPI_STATUS(AE_BAD_PARAMETER);
-	}
-
-	/* Disable the GPE if currently enabled */
-
-	status = acpi_ev_disable_gpe(gpe_event_info);
-
-	/* Clear the type bits and insert the new Type */
-
-	gpe_event_info->flags &= ~ACPI_GPE_TYPE_MASK;
-	gpe_event_info->flags |= type;
-	return_ACPI_STATUS(status);
-}
-
-/*******************************************************************************
- *
  * FUNCTION:    acpi_ev_update_gpe_enable_masks
  *
  * PARAMETERS:  gpe_event_info          - GPE to update
- *              Type                    - What to do: ACPI_GPE_DISABLE or
- *                                        ACPI_GPE_ENABLE
  *
  * RETURN:      Status
  *
@@ -110,8 +65,7 @@ acpi_ev_set_gpe_type(struct acpi_gpe_eve
  ******************************************************************************/
 
 acpi_status
-acpi_ev_update_gpe_enable_masks(struct acpi_gpe_event_info *gpe_event_info,
-				u8 type)
+acpi_ev_update_gpe_enable_masks(struct acpi_gpe_event_info *gpe_event_info)
 {
 	struct acpi_gpe_register_info *gpe_register_info;
 	u8 register_bit;
@@ -127,37 +81,14 @@ acpi_ev_update_gpe_enable_masks(struct a
 	    (1 <<
 	     (gpe_event_info->gpe_number - gpe_register_info->base_gpe_number));
 
-	/* 1) Disable case. Simply clear all enable bits */
-
-	if (type == ACPI_GPE_DISABLE) {
-		ACPI_CLEAR_BIT(gpe_register_info->enable_for_wake,
-			       register_bit);
-		ACPI_CLEAR_BIT(gpe_register_info->enable_for_run, register_bit);
-		return_ACPI_STATUS(AE_OK);
-	}
-
-	/* 2) Enable case. Set/Clear the appropriate enable bits */
+	ACPI_CLEAR_BIT(gpe_register_info->enable_for_wake, register_bit);
+	ACPI_CLEAR_BIT(gpe_register_info->enable_for_run, register_bit);
 
-	switch (gpe_event_info->flags & ACPI_GPE_TYPE_MASK) {
-	case ACPI_GPE_TYPE_WAKE:
-		ACPI_SET_BIT(gpe_register_info->enable_for_wake, register_bit);
-		ACPI_CLEAR_BIT(gpe_register_info->enable_for_run, register_bit);
-		break;
-
-	case ACPI_GPE_TYPE_RUNTIME:
-		ACPI_CLEAR_BIT(gpe_register_info->enable_for_wake,
-			       register_bit);
+	if (gpe_event_info->runtime_count)
 		ACPI_SET_BIT(gpe_register_info->enable_for_run, register_bit);
-		break;
 
-	case ACPI_GPE_TYPE_WAKE_RUN:
+	if (gpe_event_info->wakeup_count)
 		ACPI_SET_BIT(gpe_register_info->enable_for_wake, register_bit);
-		ACPI_SET_BIT(gpe_register_info->enable_for_run, register_bit);
-		break;
-
-	default:
-		return_ACPI_STATUS(AE_BAD_PARAMETER);
-	}
 
 	return_ACPI_STATUS(AE_OK);
 }
@@ -186,47 +117,20 @@ acpi_ev_enable_gpe(struct acpi_gpe_event
 
 	/* Make sure HW enable masks are updated */
 
-	status =
-	    acpi_ev_update_gpe_enable_masks(gpe_event_info, ACPI_GPE_ENABLE);
-	if (ACPI_FAILURE(status)) {
+	status = acpi_ev_update_gpe_enable_masks(gpe_event_info);
+	if (ACPI_FAILURE(status))
 		return_ACPI_STATUS(status);
-	}
 
 	/* Mark wake-enabled or HW enable, or both */
 
-	switch (gpe_event_info->flags & ACPI_GPE_TYPE_MASK) {
-	case ACPI_GPE_TYPE_WAKE:
-
-		ACPI_SET_BIT(gpe_event_info->flags, ACPI_GPE_WAKE_ENABLED);
-		break;
-
-	case ACPI_GPE_TYPE_WAKE_RUN:
-
-		ACPI_SET_BIT(gpe_event_info->flags, ACPI_GPE_WAKE_ENABLED);
-
-		/*lint -fallthrough */
-
-	case ACPI_GPE_TYPE_RUNTIME:
-
-		ACPI_SET_BIT(gpe_event_info->flags, ACPI_GPE_RUN_ENABLED);
-
-		if (write_to_hardware) {
-
-			/* Clear the GPE (of stale events), then enable it */
-
-			status = acpi_hw_clear_gpe(gpe_event_info);
-			if (ACPI_FAILURE(status)) {
-				return_ACPI_STATUS(status);
-			}
-
-			/* Enable the requested runtime GPE */
-
-			status = acpi_hw_write_gpe_enable_reg(gpe_event_info);
-		}
-		break;
+	if (gpe_event_info->runtime_count && write_to_hardware) {
+		/* Clear the GPE (of stale events), then enable it */
+		status = acpi_hw_clear_gpe(gpe_event_info);
+		if (ACPI_FAILURE(status))
+			return_ACPI_STATUS(status);
 
-	default:
-		return_ACPI_STATUS(AE_BAD_PARAMETER);
+		/* Enable the requested runtime GPE */
+		status = acpi_hw_write_gpe_enable_reg(gpe_event_info);
 	}
 
 	return_ACPI_STATUS(AE_OK);
@@ -252,34 +156,9 @@ acpi_status acpi_ev_disable_gpe(struct a
 
 	/* Make sure HW enable masks are updated */
 
-	status =
-	    acpi_ev_update_gpe_enable_masks(gpe_event_info, ACPI_GPE_DISABLE);
-	if (ACPI_FAILURE(status)) {
+	status = acpi_ev_update_gpe_enable_masks(gpe_event_info);
+	if (ACPI_FAILURE(status))
 		return_ACPI_STATUS(status);
-	}
-
-	/* Clear the appropriate enabled flags for this GPE */
-
-	switch (gpe_event_info->flags & ACPI_GPE_TYPE_MASK) {
-	case ACPI_GPE_TYPE_WAKE:
-		ACPI_CLEAR_BIT(gpe_event_info->flags, ACPI_GPE_WAKE_ENABLED);
-		break;
-
-	case ACPI_GPE_TYPE_WAKE_RUN:
-		ACPI_CLEAR_BIT(gpe_event_info->flags, ACPI_GPE_WAKE_ENABLED);
-
-		/* fallthrough */
-
-	case ACPI_GPE_TYPE_RUNTIME:
-
-		/* Disable the requested runtime GPE */
-
-		ACPI_CLEAR_BIT(gpe_event_info->flags, ACPI_GPE_RUN_ENABLED);
-		break;
-
-	default:
-		break;
-	}
 
 	/*
 	 * Even if we don't know the GPE type, make sure that we always
Index: linux-2.6/drivers/acpi/acpica/evgpeblk.c
===================================================================
--- linux-2.6.orig/drivers/acpi/acpica/evgpeblk.c
+++ linux-2.6/drivers/acpi/acpica/evgpeblk.c
@@ -258,7 +258,6 @@ acpi_ev_save_method_info(acpi_handle obj
 	u32 gpe_number;
 	char name[ACPI_NAME_SIZE + 1];
 	u8 type;
-	acpi_status status;
 
 	ACPI_FUNCTION_TRACE(ev_save_method_info);
 
@@ -325,26 +324,20 @@ acpi_ev_save_method_info(acpi_handle obj
 
 	/*
 	 * Now we can add this information to the gpe_event_info block for use
-	 * during dispatch of this GPE. Default type is RUNTIME, although this may
-	 * change when the _PRW methods are executed later.
+	 * during dispatch of this GPE.
 	 */
 	gpe_event_info =
 	    &gpe_block->event_info[gpe_number - gpe_block->block_base_number];
 
-	gpe_event_info->flags = (u8)
-	    (type | ACPI_GPE_DISPATCH_METHOD | ACPI_GPE_TYPE_RUNTIME);
+	gpe_event_info->flags = (u8) (type | ACPI_GPE_DISPATCH_METHOD);
 
 	gpe_event_info->dispatch.method_node =
 	    (struct acpi_namespace_node *)obj_handle;
 
-	/* Update enable mask, but don't enable the HW GPE as of yet */
-
-	status = acpi_ev_enable_gpe(gpe_event_info, FALSE);
-
 	ACPI_DEBUG_PRINT((ACPI_DB_LOAD,
 			  "Registered GPE method %s as GPE number 0x%.2X\n",
 			  name, gpe_number));
-	return_ACPI_STATUS(status);
+	return_ACPI_STATUS(AE_OK);
 }
 
 /*******************************************************************************
@@ -454,20 +447,7 @@ acpi_ev_match_prw_and_gpe(acpi_handle ob
 							gpe_block->
 							block_base_number];
 
-		/* Mark GPE for WAKE-ONLY but WAKE_DISABLED */
-
-		gpe_event_info->flags &=
-		    ~(ACPI_GPE_WAKE_ENABLED | ACPI_GPE_RUN_ENABLED);
-
-		status =
-		    acpi_ev_set_gpe_type(gpe_event_info, ACPI_GPE_TYPE_WAKE);
-		if (ACPI_FAILURE(status)) {
-			goto cleanup;
-		}
-
-		status =
-		    acpi_ev_update_gpe_enable_masks(gpe_event_info,
-						    ACPI_GPE_DISABLE);
+		gpe_event_info->flags |= ACPI_GPE_CAN_WAKE;
 	}
 
       cleanup:
@@ -989,7 +969,6 @@ acpi_status
 acpi_ev_initialize_gpe_block(struct acpi_namespace_node *gpe_device,
 			     struct acpi_gpe_block_info *gpe_block)
 {
-	acpi_status status;
 	struct acpi_gpe_event_info *gpe_event_info;
 	struct acpi_gpe_walk_info gpe_info;
 	u32 wake_gpe_count;
@@ -1019,42 +998,50 @@ acpi_ev_initialize_gpe_block(struct acpi
 		gpe_info.gpe_block = gpe_block;
 		gpe_info.gpe_device = gpe_device;
 
-		status =
-		    acpi_ns_walk_namespace(ACPI_TYPE_DEVICE, ACPI_ROOT_OBJECT,
+		acpi_ns_walk_namespace(ACPI_TYPE_DEVICE, ACPI_ROOT_OBJECT,
 					   ACPI_UINT32_MAX, ACPI_NS_WALK_UNLOCK,
 					   acpi_ev_match_prw_and_gpe, NULL,
 					   &gpe_info, NULL);
 	}
 
 	/*
-	 * Enable all GPEs in this block that have these attributes:
-	 * 1) are "runtime" or "run/wake" GPEs, and
-	 * 2) have a corresponding _Lxx or _Exx method
-	 *
-	 * Any other GPEs within this block must be enabled via the
-	 * acpi_enable_gpe() external interface.
+	 * Enable all GPEs that have a corresponding method and aren't
+	 * capable of generating wakeups. Any other GPEs within this block
+	 * must be enabled via the acpi_enable_gpe() interface.
 	 */
 	wake_gpe_count = 0;
 	gpe_enabled_count = 0;
+	if (gpe_device == acpi_gbl_fadt_gpe_device)
+		gpe_device = NULL;
 
 	for (i = 0; i < gpe_block->register_count; i++) {
-		for (j = 0; j < 8; j++) {
+		for (j = 0; j < ACPI_GPE_REGISTER_WIDTH; j++) {
+			acpi_status status;
+			acpi_size gpe_index;
+			int gpe_number;
 
 			/* Get the info block for this particular GPE */
+			gpe_index = (acpi_size)i * ACPI_GPE_REGISTER_WIDTH + j;
+			gpe_event_info = &gpe_block->event_info[gpe_index];
 
-			gpe_event_info = &gpe_block->event_info[((acpi_size) i *
-								 ACPI_GPE_REGISTER_WIDTH)
-								+ j];
-
-			if (((gpe_event_info->flags & ACPI_GPE_DISPATCH_MASK) ==
-			     ACPI_GPE_DISPATCH_METHOD) &&
-			    (gpe_event_info->flags & ACPI_GPE_TYPE_RUNTIME)) {
-				gpe_enabled_count++;
-			}
-
-			if (gpe_event_info->flags & ACPI_GPE_TYPE_WAKE) {
+			if (gpe_event_info->flags & ACPI_GPE_CAN_WAKE) {
 				wake_gpe_count++;
+				if (acpi_gbl_leave_wake_gpes_disabled)
+					continue;
 			}
+
+			if (!(gpe_event_info->flags & ACPI_GPE_DISPATCH_METHOD))
+				continue;
+
+			gpe_number = gpe_index + gpe_block->block_base_number;
+			status = acpi_enable_gpe(gpe_device, gpe_number,
+						ACPI_GPE_TYPE_RUNTIME);
+			if (ACPI_FAILURE(status))
+				ACPI_ERROR((AE_INFO,
+						"Failed to enable GPE %02X\n",
+						gpe_number));
+			else
+				gpe_enabled_count++;
 		}
 	}
 
@@ -1062,15 +1049,7 @@ acpi_ev_initialize_gpe_block(struct acpi
 			  "Found %u Wake, Enabled %u Runtime GPEs in this block\n",
 			  wake_gpe_count, gpe_enabled_count));
 
-	/* Enable all valid runtime GPEs found above */
-
-	status = acpi_hw_enable_runtime_gpe_block(NULL, gpe_block, NULL);
-	if (ACPI_FAILURE(status)) {
-		ACPI_ERROR((AE_INFO, "Could not enable GPEs in GpeBlock %p",
-			    gpe_block));
-	}
-
-	return_ACPI_STATUS(status);
+	return_ACPI_STATUS(AE_OK);
 }
 
 /*******************************************************************************
Index: linux-2.6/drivers/acpi/acpica/evxface.c
===================================================================
--- linux-2.6.orig/drivers/acpi/acpica/evxface.c
+++ linux-2.6/drivers/acpi/acpica/evxface.c
@@ -617,13 +617,6 @@ acpi_install_gpe_handler(acpi_handle gpe
 	handler->context = context;
 	handler->method_node = gpe_event_info->dispatch.method_node;
 
-	/* Disable the GPE before installing the handler */
-
-	status = acpi_ev_disable_gpe(gpe_event_info);
-	if (ACPI_FAILURE(status)) {
-		goto unlock_and_exit;
-	}
-
 	/* Install the handler */
 
 	flags = acpi_os_acquire_lock(acpi_gbl_gpe_lock);
@@ -707,13 +700,6 @@ acpi_remove_gpe_handler(acpi_handle gpe_
 		goto unlock_and_exit;
 	}
 
-	/* Disable the GPE before removing the handler */
-
-	status = acpi_ev_disable_gpe(gpe_event_info);
-	if (ACPI_FAILURE(status)) {
-		goto unlock_and_exit;
-	}
-
 	/* Make sure all deferred tasks are completed */
 
 	(void)acpi_ut_release_mutex(ACPI_MTX_EVENTS);
Index: linux-2.6/include/acpi/actypes.h
===================================================================
--- linux-2.6.orig/include/acpi/actypes.h
+++ linux-2.6/include/acpi/actypes.h
@@ -668,15 +668,16 @@ typedef u32 acpi_event_status;
 
 /*
  * GPE info flags - Per GPE
- * +-+-+-+---+---+-+
- * |7|6|5|4:3|2:1|0|
- * +-+-+-+---+---+-+
- *  | | |  |   |  |
- *  | | |  |   |  +--- Interrupt type: Edge or Level Triggered
- *  | | |  |   +--- Type: Wake-only, Runtime-only, or wake/runtime
+ * +-+-+-+---+-+-+-+
+ * |7|6|5|4:3|2|1|0|
+ * +-+-+-+---+-+-+-+
+ *  | | |  |  | | |
+ *  | | |  |  | | +--- Interrupt type: Edge or Level Triggered
+ *  | | |  |  | +--- GPE can wake the system
+ *  | | |  |  +--- Unused
  *  | | |  +--- Type of dispatch -- to method, handler, or none
- *  | | +--- Enabled for runtime?
- *  | +--- Enabled for wake?
+ *  | | +--- Unused
+ *  | +--- Unused
  *  +--- Unused
  */
 #define ACPI_GPE_XRUPT_TYPE_MASK        (u8) 0x01
@@ -687,22 +688,13 @@ typedef u32 acpi_event_status;
 #define ACPI_GPE_TYPE_WAKE_RUN          (u8) 0x06
 #define ACPI_GPE_TYPE_WAKE              (u8) 0x02
 #define ACPI_GPE_TYPE_RUNTIME           (u8) 0x04	/* Default */
+#define ACPI_GPE_CAN_WAKE		(u8) 0x02
 
 #define ACPI_GPE_DISPATCH_MASK          (u8) 0x18
 #define ACPI_GPE_DISPATCH_HANDLER       (u8) 0x08
 #define ACPI_GPE_DISPATCH_METHOD        (u8) 0x10
 #define ACPI_GPE_DISPATCH_NOT_USED      (u8) 0x00	/* Default */
 
-#define ACPI_GPE_RUN_ENABLE_MASK        (u8) 0x20
-#define ACPI_GPE_RUN_ENABLED            (u8) 0x20
-#define ACPI_GPE_RUN_DISABLED           (u8) 0x00	/* Default */
-
-#define ACPI_GPE_WAKE_ENABLE_MASK       (u8) 0x40
-#define ACPI_GPE_WAKE_ENABLED           (u8) 0x40
-#define ACPI_GPE_WAKE_DISABLED          (u8) 0x00	/* Default */
-
-#define ACPI_GPE_ENABLE_MASK            (u8) 0x60	/* Both run/wake */
-
 /*
  * Flags for GPE and Lock interfaces
  */
Index: linux-2.6/drivers/acpi/system.c
===================================================================
--- linux-2.6.orig/drivers/acpi/system.c
+++ linux-2.6/drivers/acpi/system.c
@@ -387,10 +387,10 @@ static ssize_t counter_set(struct kobjec
 	if (index < num_gpes) {
 		if (!strcmp(buf, "disable\n") &&
 				(status & ACPI_EVENT_FLAG_ENABLED))
-			result = acpi_disable_gpe(handle, index);
+			result = acpi_set_gpe(handle, index, ACPI_GPE_DISABLE);
 		else if (!strcmp(buf, "enable\n") &&
 				!(status & ACPI_EVENT_FLAG_ENABLED))
-			result = acpi_enable_gpe(handle, index);
+			result = acpi_set_gpe(handle, index, ACPI_GPE_ENABLE);
 		else if (!strcmp(buf, "clear\n") &&
 				(status & ACPI_EVENT_FLAG_SET))
 			result = acpi_clear_gpe(handle, index, ACPI_NOT_ISR);

[PATCH 5/8] ACPI / PM: Add more run-time wake-up fields (rev. 2)

[Rafael J. Wysocki]

From: Rafael J. Wysocki <rjw@sisk.pl>

Use the run_wake flag to mark all devices for which run-time wake-up
events may be generated by the platform.  Introduce a new wake-up
flag, always_enabled, for marking devices that should be permanently
enabled to generate run-time events.  Also, introduce a reference
counter for run-wake devices and a function that will initialize all
of the run-time wake-up fields for given device.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
---
 drivers/acpi/button.c   |    2 ++
 drivers/acpi/scan.c     |   37 +++++++++++++++++++++++++++----------
 drivers/acpi/wakeup.c   |    3 ++-
 include/acpi/acpi_bus.h |    2 ++
 4 files changed, 33 insertions(+), 11 deletions(-)

Index: linux-2.6/drivers/acpi/wakeup.c
===================================================================
--- linux-2.6.orig/drivers/acpi/wakeup.c
+++ linux-2.6/drivers/acpi/wakeup.c
@@ -110,7 +110,8 @@ int __init acpi_wakeup_device_init(void)
 						       struct acpi_device,
 						       wakeup_list);
 		/* In case user doesn't load button driver */
-		if (!dev->wakeup.flags.run_wake || dev->wakeup.state.enabled)
+		if (!dev->wakeup.flags.always_enabled ||
+		    dev->wakeup.state.enabled)
 			continue;
  		acpi_enable_gpe(dev->wakeup.gpe_device, dev->wakeup.gpe_number,
  				ACPI_GPE_TYPE_WAKE);
Index: linux-2.6/include/acpi/acpi_bus.h
===================================================================
--- linux-2.6.orig/include/acpi/acpi_bus.h
+++ linux-2.6/include/acpi/acpi_bus.h
@@ -242,6 +242,7 @@ struct acpi_device_perf {
 struct acpi_device_wakeup_flags {
 	u8 valid:1;		/* Can successfully enable wakeup? */
 	u8 run_wake:1;		/* Run-Wake GPE devices */
+	u8 always_enabled:1;	/* Run-wake devices that are always enabled */
 };
 
 struct acpi_device_wakeup_state {
@@ -256,6 +257,7 @@ struct acpi_device_wakeup {
 	struct acpi_device_wakeup_state state;
 	struct acpi_device_wakeup_flags flags;
 	int prepare_count;
+	int run_wake_count;
 };
 
 /* Device */
Index: linux-2.6/drivers/acpi/button.c
===================================================================
--- linux-2.6.orig/drivers/acpi/button.c
+++ linux-2.6/drivers/acpi/button.c
@@ -425,6 +425,7 @@ static int acpi_button_add(struct acpi_d
 		acpi_enable_gpe(device->wakeup.gpe_device,
 				device->wakeup.gpe_number,
 				ACPI_GPE_TYPE_WAKE_RUN);
+		device->wakeup.run_wake_count++;
 		device->wakeup.state.enabled = 1;
 	}
 
@@ -448,6 +449,7 @@ static int acpi_button_remove(struct acp
 		acpi_disable_gpe(device->wakeup.gpe_device,
 				device->wakeup.gpe_number,
 				ACPI_GPE_TYPE_WAKE_RUN);
+		device->wakeup.run_wake_count--;
 		device->wakeup.state.enabled = 0;
 	}
 
Index: linux-2.6/drivers/acpi/scan.c
===================================================================
--- linux-2.6.orig/drivers/acpi/scan.c
+++ linux-2.6/drivers/acpi/scan.c
@@ -741,19 +741,39 @@ acpi_bus_extract_wakeup_device_power_pac
 	return AE_OK;
 }
 
-static int acpi_bus_get_wakeup_device_flags(struct acpi_device *device)
+static void acpi_bus_set_run_wake_flags(struct acpi_device *device)
 {
-	acpi_status status = 0;
-	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
-	union acpi_object *package = NULL;
-	int psw_error;
-
 	struct acpi_device_id button_device_ids[] = {
 		{"PNP0C0D", 0},
 		{"PNP0C0C", 0},
 		{"PNP0C0E", 0},
 		{"", 0},
 	};
+	acpi_status status;
+	acpi_event_status event_status;
+
+	device->wakeup.run_wake_count = 0;
+
+	/* Power button, Lid switch always enable wakeup */
+	if (!acpi_match_device_ids(device, button_device_ids)) {
+		device->wakeup.flags.run_wake = 1;
+		device->wakeup.flags.always_enabled = 1;
+		return;
+	}
+
+	status = acpi_get_gpe_status(NULL, device->wakeup.gpe_number,
+					ACPI_NOT_ISR, &event_status);
+	if (status == AE_OK)
+		device->wakeup.flags.run_wake =
+				!!(event_status & ACPI_EVENT_FLAG_HANDLE);
+}
+
+static int acpi_bus_get_wakeup_device_flags(struct acpi_device *device)
+{
+	acpi_status status = 0;
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	union acpi_object *package = NULL;
+	int psw_error;
 
 	/* _PRW */
 	status = acpi_evaluate_object(device->handle, "_PRW", NULL, &buffer);
@@ -773,6 +793,7 @@ static int acpi_bus_get_wakeup_device_fl
 
 	device->wakeup.flags.valid = 1;
 	device->wakeup.prepare_count = 0;
+	acpi_bus_set_run_wake_flags(device);
 	/* Call _PSW/_DSW object to disable its ability to wake the sleeping
 	 * system for the ACPI device with the _PRW object.
 	 * The _PSW object is depreciated in ACPI 3.0 and is replaced by _DSW.
@@ -784,10 +805,6 @@ static int acpi_bus_get_wakeup_device_fl
 		ACPI_DEBUG_PRINT((ACPI_DB_INFO,
 				"error in _DSW or _PSW evaluation\n"));
 
-	/* Power button, Lid switch always enable wakeup */
-	if (!acpi_match_device_ids(device, button_device_ids))
-		device->wakeup.flags.run_wake = 1;
-
 end:
 	if (ACPI_FAILURE(status))
 		device->flags.wake_capable = 0;

[PATCH 6/8] ACPI / ACPICA: Multiple system notify handlers per device

[Rafael J. Wysocki]

From: Rafael J. Wysocki <rjw@sisk.pl>

Currently it only is possible to install one system notify handler
per namespace node, but this is not enough for PCI run-time power
management, because we need to install power management notifiers for
devices that already have hotplug notifiers installed.  While in
principle this could be handled at the PCI level, that would be
suboptimal due to the way in which the ACPI-based PCI hotplug code is
designed.

For this reason, modify ACPICA so that it is possible to install more
than one system notify handler per namespace node.  Namely, make
acpi_install_notify_handler(), acpi_remove_notify_handler() and
acpi_ev_notify_dispatch() use a list of system notify handler objects
associated with a namespace node.

Make acpi_remove_notify_handler() call acpi_os_wait_events_complete()
upfront to avoid a situation in which concurrent instance of
acpi_remove_notify_handler() removes the handler from under us while
we're waiting for the event queues to flush.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 drivers/acpi/acpica/acobject.h |    2 
 drivers/acpi/acpica/evmisc.c   |   12 ++
 drivers/acpi/acpica/evxface.c  |  175 ++++++++++++++++++++++++++++++++---------
 3 files changed, 150 insertions(+), 39 deletions(-)

Index: linux-2.6/drivers/acpi/acpica/acobject.h
===================================================================
--- linux-2.6.orig/drivers/acpi/acpica/acobject.h
+++ linux-2.6/drivers/acpi/acpica/acobject.h
@@ -287,8 +287,10 @@ struct acpi_object_buffer_field {
 
 struct acpi_object_notify_handler {
 	ACPI_OBJECT_COMMON_HEADER struct acpi_namespace_node *node;	/* Parent device */
+	u32 handler_type;
 	acpi_notify_handler handler;
 	void *context;
+	struct acpi_object_notify_handler *next;
 };
 
 struct acpi_object_addr_handler {
Index: linux-2.6/drivers/acpi/acpica/evxface.c
===================================================================
--- linux-2.6.orig/drivers/acpi/acpica/evxface.c
+++ linux-2.6/drivers/acpi/acpica/evxface.c
@@ -218,6 +218,72 @@ ACPI_EXPORT_SYMBOL(acpi_remove_fixed_eve
 
 /*******************************************************************************
  *
+ * FUNCTION:    acpi_populate_handler_object
+ *
+ * PARAMETERS:  handler_obj        - Handler object to populate
+ *              handler_type       - The type of handler:
+ *                                  ACPI_SYSTEM_NOTIFY: system_handler (00-7f)
+ *                                  ACPI_DEVICE_NOTIFY: driver_handler (80-ff)
+ *                                  ACPI_ALL_NOTIFY:  both system and device
+ *              handler            - Address of the handler
+ *              context            - Value passed to the handler on each GPE
+ *              next               - Address of a handler object to link to
+ *
+ * RETURN:      None
+ *
+ * DESCRIPTION: Populate a handler object.
+ *
+ ******************************************************************************/
+static void
+acpi_populate_handler_object(struct acpi_object_notify_handler *handler_obj,
+			     u32 handler_type,
+			     acpi_notify_handler handler, void *context,
+			     struct acpi_object_notify_handler *next)
+{
+	handler_obj->handler_type = handler_type;
+	handler_obj->handler = handler;
+	handler_obj->context = context;
+	handler_obj->next = next;
+}
+
+/*******************************************************************************
+ *
+ * FUNCTION:    acpi_add_handler_object
+ *
+ * PARAMETERS:  parent_obj         - Parent of the new object
+ *              handler            - Address of the handler
+ *              context            - Value passed to the handler on each GPE
+ *
+ * RETURN:      Status
+ *
+ * DESCRIPTION: Create a new handler object and populate it.
+ *
+ ******************************************************************************/
+static acpi_status
+acpi_add_handler_object(struct acpi_object_notify_handler *parent_obj,
+			acpi_notify_handler handler, void *context)
+{
+	struct acpi_object_notify_handler *handler_obj;
+
+	/* The parent must not be a defice notify handler object. */
+	if (parent_obj->handler_type & ACPI_DEVICE_NOTIFY)
+		return AE_BAD_PARAMETER;
+
+	handler_obj = ACPI_ALLOCATE_ZEROED(sizeof(*handler_obj));
+	if (!handler_obj)
+		return AE_NO_MEMORY;
+
+	acpi_populate_handler_object(handler_obj,
+					ACPI_SYSTEM_NOTIFY,
+					handler, context,
+					parent_obj->next);
+	parent_obj->next = handler_obj;
+
+	return AE_OK;
+}
+
+/*******************************************************************************
+ *
  * FUNCTION:    acpi_install_notify_handler
  *
  * PARAMETERS:  Device          - The device for which notifies will be handled
@@ -316,15 +382,32 @@ acpi_install_notify_handler(acpi_handle 
 		obj_desc = acpi_ns_get_attached_object(node);
 		if (obj_desc) {
 
-			/* Object exists - make sure there's no handler */
+			/* Object exists. */
 
-			if (((handler_type & ACPI_SYSTEM_NOTIFY) &&
-			     obj_desc->common_notify.system_notify) ||
-			    ((handler_type & ACPI_DEVICE_NOTIFY) &&
-			     obj_desc->common_notify.device_notify)) {
+			/* For a device notify, make sure there's no handler. */
+			if ((handler_type & ACPI_DEVICE_NOTIFY) &&
+			     obj_desc->common_notify.device_notify) {
 				status = AE_ALREADY_EXISTS;
 				goto unlock_and_exit;
 			}
+
+			/* System notifies may have more handlers installed. */
+			notify_obj = obj_desc->common_notify.system_notify;
+
+			if ((handler_type & ACPI_SYSTEM_NOTIFY) && notify_obj) {
+				struct acpi_object_notify_handler *parent_obj;
+
+				if (handler_type & ACPI_DEVICE_NOTIFY) {
+					status = AE_ALREADY_EXISTS;
+					goto unlock_and_exit;
+				}
+
+				parent_obj = &notify_obj->notify;
+				status = acpi_add_handler_object(parent_obj,
+								 handler,
+								 context);
+				goto unlock_and_exit;
+			}
 		} else {
 			/* Create a new object */
 
@@ -356,9 +439,10 @@ acpi_install_notify_handler(acpi_handle 
 			goto unlock_and_exit;
 		}
 
-		notify_obj->notify.node = node;
-		notify_obj->notify.handler = handler;
-		notify_obj->notify.context = context;
+		acpi_populate_handler_object(&notify_obj->notify,
+						handler_type,
+						handler, context,
+						NULL);
 
 		if (handler_type & ACPI_SYSTEM_NOTIFY) {
 			obj_desc->common_notify.system_notify = notify_obj;
@@ -418,6 +502,10 @@ acpi_remove_notify_handler(acpi_handle d
 		goto exit;
 	}
 
+
+	/* Make sure all deferred tasks are completed */
+	acpi_os_wait_events_complete(NULL);
+
 	status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
 	if (ACPI_FAILURE(status)) {
 		goto exit;
@@ -445,15 +533,6 @@ acpi_remove_notify_handler(acpi_handle d
 			goto unlock_and_exit;
 		}
 
-		/* Make sure all deferred tasks are completed */
-
-		(void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE);
-		acpi_os_wait_events_complete(NULL);
-		status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
-		if (ACPI_FAILURE(status)) {
-			goto exit;
-		}
-
 		if (handler_type & ACPI_SYSTEM_NOTIFY) {
 			acpi_gbl_system_notify.node = NULL;
 			acpi_gbl_system_notify.handler = NULL;
@@ -488,28 +567,60 @@ acpi_remove_notify_handler(acpi_handle d
 		/* Object exists - make sure there's an existing handler */
 
 		if (handler_type & ACPI_SYSTEM_NOTIFY) {
+			struct acpi_object_notify_handler *handler_obj;
+			struct acpi_object_notify_handler *parent_obj;
+
 			notify_obj = obj_desc->common_notify.system_notify;
 			if (!notify_obj) {
 				status = AE_NOT_EXIST;
 				goto unlock_and_exit;
 			}
 
-			if (notify_obj->notify.handler != handler) {
+			handler_obj = &notify_obj->notify;
+			parent_obj = NULL;
+			while (handler_obj->handler != handler) {
+				if (handler_obj->next) {
+					parent_obj = handler_obj;
+					handler_obj = handler_obj->next;
+				} else {
+					break;
+				}
+			}
+
+			if (handler_obj->handler != handler) {
 				status = AE_BAD_PARAMETER;
 				goto unlock_and_exit;
 			}
-			/* Make sure all deferred tasks are completed */
 
-			(void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE);
-			acpi_os_wait_events_complete(NULL);
-			status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
-			if (ACPI_FAILURE(status)) {
-				goto exit;
+			/*
+			 * Remove the handler.  There are three possible cases.
+			 * First, we may need to remove a non-embedded object.
+			 * Second, we may need to remove the embedded object's
+			 * handler data, while non-embedded objects exist.
+			 * Finally, we may need to remove the embedded object
+			 * entirely along with its container.
+			 */
+			if (parent_obj) {
+				/* Non-embedded object is being removed. */
+				parent_obj->next = handler_obj->next;
+				ACPI_FREE(handler_obj);
+			} else if (notify_obj->notify.next) {
+				/*
+				 * The handler matches the embedded object, but
+				 * there are more handler objects in the list.
+				 * Replace the embedded object's data with the
+				 * first next object's data and remove that
+				 * object.
+				 */
+				parent_obj = &notify_obj->notify;
+				handler_obj = notify_obj->notify.next;
+				*parent_obj = *handler_obj;
+				ACPI_FREE(handler_obj);
+			} else {
+				/* No more handler objects in the list. */
+				obj_desc->common_notify.system_notify = NULL;
+				acpi_ut_remove_reference(notify_obj);
 			}
-
-			/* Remove the handler */
-			obj_desc->common_notify.system_notify = NULL;
-			acpi_ut_remove_reference(notify_obj);
 		}
 
 		if (handler_type & ACPI_DEVICE_NOTIFY) {
@@ -523,14 +634,6 @@ acpi_remove_notify_handler(acpi_handle d
 				status = AE_BAD_PARAMETER;
 				goto unlock_and_exit;
 			}
-			/* Make sure all deferred tasks are completed */
-
-			(void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE);
-			acpi_os_wait_events_complete(NULL);
-			status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
-			if (ACPI_FAILURE(status)) {
-				goto exit;
-			}
 
 			/* Remove the handler */
 			obj_desc->common_notify.device_notify = NULL;
Index: linux-2.6/drivers/acpi/acpica/evmisc.c
===================================================================
--- linux-2.6.orig/drivers/acpi/acpica/evmisc.c
+++ linux-2.6/drivers/acpi/acpica/evmisc.c
@@ -259,9 +259,15 @@ static void ACPI_SYSTEM_XFACE acpi_ev_no
 
 	handler_obj = notify_info->notify.handler_obj;
 	if (handler_obj) {
-		handler_obj->notify.handler(notify_info->notify.node,
-					    notify_info->notify.value,
-					    handler_obj->notify.context);
+		struct acpi_object_notify_handler *notifier;
+
+		notifier = &handler_obj->notify;
+		while (notifier) {
+			notifier->handler(notify_info->notify.node,
+					  notify_info->notify.value,
+					  notifier->context);
+			notifier = notifier->next;
+		}
 	}
 
 	/* All done with the info object */

[PATCH 7/8] PCI / ACPI / PM: Platform support for PCI PME wake-up (rev. 9)

[Rafael J. Wysocki]

From: Rafael J. Wysocki <rjw@sisk.pl>

Although the majority of PCI devices can generate PMEs that in
principle may be used to wake up devices suspended at run time,
platform support is generally necessary to convert PMEs into wake-up
events that can be delivered to the kernel.  If ACPI is used for this
purpose, PME signals generated by a PCI device will trigger the ACPI
GPE associated with the device to generate an ACPI wake-up event that
we can set up a handler for, provided that everything is configured
correctly.

Unfortunately, the subset of PCI devices that have GPEs associated
with them is quite limited.  The devices without dedicated GPEs have
to rely on the GPEs associated with other devices (in the majority of
cases their upstream bridges and, possibly, the root bridge) to
generate ACPI wake-up events in response to PME signals from them.

Add ACPI platform support for PCI PME wake-up:
o Add a framework making is possible to use ACPI system notify
  handlers for run-time PM.
o Add new PCI platform callback ->run_wake() to struct
  pci_platform_pm_ops allowing us to enable/disable the platform to
  generate wake-up events for given device.  Implemet this callback
  for the ACPI platform.
o Define ACPI wake-up handlers for PCI devices and PCI root buses and
  make the PCI-ACPI binding code register wake-up notifiers for all
  PCI devices present in the ACPI tables.
o Add function pci_dev_run_wake() which can be used by PCI drivers to
  check if given device is capable of generating wake-up events at
  run time.

Developed in cooperation with Matthew Garrett <mjg@redhat.com>.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 drivers/acpi/internal.h  |    2 
 drivers/acpi/pci_bind.c  |   14 ++-
 drivers/acpi/pci_root.c  |    8 +
 drivers/acpi/scan.c      |    1 
 drivers/pci/pci-acpi.c   |  211 +++++++++++++++++++++++++++++++++++++++++++++++
 drivers/pci/pci.c        |   67 ++++++++++++++
 drivers/pci/pci.h        |    7 +
 include/acpi/acpi_bus.h  |    4 
 include/linux/pci-acpi.h |    7 +
 include/linux/pci.h      |    1 
 10 files changed, 319 insertions(+), 3 deletions(-)

Index: linux-2.6/drivers/pci/pci.h
===================================================================
--- linux-2.6.orig/drivers/pci/pci.h
+++ linux-2.6/drivers/pci/pci.h
@@ -35,6 +35,10 @@ int pci_probe_reset_function(struct pci_
  *
  * @sleep_wake: enables/disables the system wake up capability of given device
  *
+ * @run_wake: enables/disables the platform to generate run-time wake-up events
+ *		for given device (the device's wake-up capability has to be
+ *		enabled by @sleep_wake for this feature to work)
+ *
  * If given platform is generally capable of power managing PCI devices, all of
  * these callbacks are mandatory.
  */
@@ -44,12 +48,15 @@ struct pci_platform_pm_ops {
 	pci_power_t (*choose_state)(struct pci_dev *dev);
 	bool (*can_wakeup)(struct pci_dev *dev);
 	int (*sleep_wake)(struct pci_dev *dev, bool enable);
+	int (*run_wake)(struct pci_dev *dev, bool enable);
 };
 
 extern int pci_set_platform_pm(struct pci_platform_pm_ops *ops);
 extern void pci_update_current_state(struct pci_dev *dev, pci_power_t state);
 extern void pci_disable_enabled_device(struct pci_dev *dev);
 extern bool pci_check_pme_status(struct pci_dev *dev);
+extern int __pci_pme_wakeup(struct pci_dev *dev, void *ign);
+extern void pci_pme_wakeup_bus(struct pci_bus *bus);
 extern void pci_pm_init(struct pci_dev *dev);
 extern void platform_pci_wakeup_init(struct pci_dev *dev);
 extern void pci_allocate_cap_save_buffers(struct pci_dev *dev);
Index: linux-2.6/drivers/pci/pci-acpi.c
===================================================================
--- linux-2.6.orig/drivers/pci/pci-acpi.c
+++ linux-2.6/drivers/pci/pci-acpi.c
@@ -16,8 +16,144 @@
 #include <acpi/acpi_bus.h>
 
 #include <linux/pci-acpi.h>
+#include <linux/pm_runtime.h>
 #include "pci.h"
 
+static DEFINE_MUTEX(pci_acpi_pm_notify_mtx);
+
+/**
+ * pci_acpi_wake_bus - Wake-up notification handler for root buses.
+ * @handle: ACPI handle of a device the notification is for.
+ * @event: Type of the signaled event.
+ * @context: PCI root bus to wake up devices on.
+ */
+static void pci_acpi_wake_bus(acpi_handle handle, u32 event, void *context)
+{
+	struct pci_bus *pci_bus = context;
+
+	if (event == ACPI_NOTIFY_DEVICE_WAKE && pci_bus)
+		pci_pme_wakeup_bus(pci_bus);
+}
+
+/**
+ * pci_acpi_wake_dev - Wake-up notification handler for PCI devices.
+ * @handle: ACPI handle of a device the notification is for.
+ * @event: Type of the signaled event.
+ * @context: PCI device object to wake up.
+ */
+static void pci_acpi_wake_dev(acpi_handle handle, u32 event, void *context)
+{
+	struct pci_dev *pci_dev = context;
+
+	if (event == ACPI_NOTIFY_DEVICE_WAKE && pci_dev) {
+		pci_check_pme_status(pci_dev);
+		pm_runtime_resume(&pci_dev->dev);
+		if (pci_dev->subordinate)
+			pci_pme_wakeup_bus(pci_dev->subordinate);
+	}
+}
+
+/**
+ * add_pm_notifier - Register PM notifier for given ACPI device.
+ * @dev: ACPI device to add the notifier for.
+ * @context: PCI device or bus to check for PME status if an event is signaled.
+ *
+ * NOTE: @dev need not be a run-wake or wake-up device to be a valid source of
+ * PM wake-up events.  For example, wake-up events may be generated for bridges
+ * if one of the devices below the bridge is signaling PME, even if the bridge
+ * itself doesn't have a wake-up GPE associated with it.
+ */
+static acpi_status add_pm_notifier(struct acpi_device *dev,
+				   acpi_notify_handler handler,
+				   void *context)
+{
+	acpi_status status = AE_ALREADY_EXISTS;
+
+	mutex_lock(&pci_acpi_pm_notify_mtx);
+
+	if (dev->wakeup.flags.notifier_present)
+		goto out;
+
+	status = acpi_install_notify_handler(dev->handle,
+					     ACPI_SYSTEM_NOTIFY,
+					     handler, context);
+	if (ACPI_FAILURE(status))
+		goto out;
+
+	dev->wakeup.flags.notifier_present = true;
+
+ out:
+	mutex_unlock(&pci_acpi_pm_notify_mtx);
+	return status;
+}
+
+/**
+ * remove_pm_notifier - Unregister PM notifier from given ACPI device.
+ * @dev: ACPI device to remove the notifier from.
+ */
+static acpi_status remove_pm_notifier(struct acpi_device *dev,
+				      acpi_notify_handler handler)
+{
+	acpi_status status = AE_BAD_PARAMETER;
+
+	mutex_lock(&pci_acpi_pm_notify_mtx);
+
+	if (!dev->wakeup.flags.notifier_present)
+		goto out;
+
+	status = acpi_remove_notify_handler(dev->handle,
+					    ACPI_SYSTEM_NOTIFY,
+					    handler);
+	if (ACPI_FAILURE(status))
+		goto out;
+
+	dev->wakeup.flags.notifier_present = false;
+
+ out:
+	mutex_unlock(&pci_acpi_pm_notify_mtx);
+	return status;
+}
+
+/**
+ * pci_acpi_add_bus_pm_notifier - Register PM notifier for given PCI bus.
+ * @dev: ACPI device to add the notifier for.
+ * @pci_bus: PCI bus to walk checking for PME status if an event is signaled.
+ */
+acpi_status pci_acpi_add_bus_pm_notifier(struct acpi_device *dev,
+					 struct pci_bus *pci_bus)
+{
+	return add_pm_notifier(dev, pci_acpi_wake_bus, pci_bus);
+}
+
+/**
+ * pci_acpi_remove_bus_pm_notifier - Unregister PCI bus PM notifier.
+ * @dev: ACPI device to remove the notifier from.
+ */
+acpi_status pci_acpi_remove_bus_pm_notifier(struct acpi_device *dev)
+{
+	return remove_pm_notifier(dev, pci_acpi_wake_bus);
+}
+
+/**
+ * pci_acpi_add_pm_notifier - Register PM notifier for given PCI device.
+ * @dev: ACPI device to add the notifier for.
+ * @pci_dev: PCI device to check for the PME status if an event is signaled.
+ */
+acpi_status pci_acpi_add_pm_notifier(struct acpi_device *dev,
+				     struct pci_dev *pci_dev)
+{
+	return add_pm_notifier(dev, pci_acpi_wake_dev, pci_dev);
+}
+
+/**
+ * pci_acpi_remove_pm_notifier - Unregister PCI device PM notifier.
+ * @dev: ACPI device to remove the notifier from.
+ */
+acpi_status pci_acpi_remove_pm_notifier(struct acpi_device *dev)
+{
+	return remove_pm_notifier(dev, pci_acpi_wake_dev);
+}
+
 /*
  * _SxD returns the D-state with the highest power
  * (lowest D-state number) supported in the S-state "x".
@@ -131,12 +267,87 @@ static int acpi_pci_sleep_wake(struct pc
 	return 0;
 }
 
+/**
+ * acpi_dev_run_wake - Enable/disable wake-up for given device.
+ * @phys_dev: Device to enable/disable the platform to wake-up the system for.
+ * @enable: Whether enable or disable the wake-up functionality.
+ *
+ * Find the ACPI device object corresponding to @pci_dev and try to
+ * enable/disable the GPE associated with it.
+ */
+static int acpi_dev_run_wake(struct device *phys_dev, bool enable)
+{
+	struct acpi_device *dev;
+	acpi_handle handle;
+	int error = -ENODEV;
+
+	if (!device_run_wake(phys_dev))
+		return -EINVAL;
+
+	handle = DEVICE_ACPI_HANDLE(phys_dev);
+	if (!handle || ACPI_FAILURE(acpi_bus_get_device(handle, &dev))) {
+		dev_dbg(phys_dev, "ACPI handle has no context in %s!\n",
+			__func__);
+		return -ENODEV;
+	}
+
+	if (enable) {
+		if (!dev->wakeup.run_wake_count++) {
+			acpi_enable_wakeup_device_power(dev, ACPI_STATE_S0);
+			acpi_enable_gpe(dev->wakeup.gpe_device,
+					dev->wakeup.gpe_number,
+					ACPI_GPE_TYPE_RUNTIME);
+		}
+	} else if (dev->wakeup.run_wake_count > 0) {
+		if (!--dev->wakeup.run_wake_count) {
+			acpi_disable_gpe(dev->wakeup.gpe_device,
+					 dev->wakeup.gpe_number,
+					 ACPI_GPE_TYPE_RUNTIME);
+			acpi_disable_wakeup_device_power(dev);
+		}
+	} else {
+		error = -EALREADY;
+	}
+
+	return error;
+}
+
+static void acpi_pci_propagate_run_wake(struct pci_bus *bus, bool enable)
+{
+	while (bus->parent) {
+		struct pci_dev *bridge = bus->self;
+
+		if (bridge->pme_interrupt)
+			return;
+		if (!acpi_dev_run_wake(&bridge->dev, enable))
+			return;
+		bus = bus->parent;
+	}
+
+	/* We have reached the root bus. */
+	if (bus->bridge)
+		acpi_dev_run_wake(bus->bridge, enable);
+}
+
+static int acpi_pci_run_wake(struct pci_dev *dev, bool enable)
+{
+	if (dev->pme_interrupt)
+		return 0;
+
+	if (!acpi_dev_run_wake(&dev->dev, enable))
+		return 0;
+
+	acpi_pci_propagate_run_wake(dev->bus, enable);
+	return 0;
+}
+
 static struct pci_platform_pm_ops acpi_pci_platform_pm = {
 	.is_manageable = acpi_pci_power_manageable,
 	.set_state = acpi_pci_set_power_state,
 	.choose_state = acpi_pci_choose_state,
 	.can_wakeup = acpi_pci_can_wakeup,
 	.sleep_wake = acpi_pci_sleep_wake,
+	.run_wake = acpi_pci_run_wake,
 };
 
 /* ACPI bus type */
Index: linux-2.6/drivers/pci/pci.c
===================================================================
--- linux-2.6.orig/drivers/pci/pci.c
+++ linux-2.6/drivers/pci/pci.c
@@ -20,6 +20,7 @@
 #include <linux/pm_wakeup.h>
 #include <linux/interrupt.h>
 #include <linux/device.h>
+#include <linux/pm_runtime.h>
 #include <asm/setup.h>
 #include "pci.h"
 
@@ -462,6 +463,12 @@ static inline int platform_pci_sleep_wak
 			pci_platform_pm->sleep_wake(dev, enable) : -ENODEV;
 }
 
+static inline int platform_pci_run_wake(struct pci_dev *dev, bool enable)
+{
+	return pci_platform_pm ?
+			pci_platform_pm->run_wake(dev, enable) : -ENODEV;
+}
+
 /**
  * pci_raw_set_power_state - Use PCI PM registers to set the power state of
  *                           given PCI device
@@ -1230,6 +1237,31 @@ bool pci_check_pme_status(struct pci_dev
 }
 
 /**
+ * pci_pme_wakeup - Wake up a PCI device if its PME Status bit is set.
+ * @dev: Device to handle.
+ * @ign: Ignored.
+ *
+ * Check if @dev has generated PME and queue a resume request for it in that
+ * case.
+ */
+static int pci_pme_wakeup(struct pci_dev *dev, void *ign)
+{
+	if (pci_check_pme_status(dev))
+		pm_request_resume(&dev->dev);
+	return 0;
+}
+
+/**
+ * pci_pme_wakeup_bus - Walk given bus and wake up devices on it, if necessary.
+ * @bus: Top bus of the subtree to walk.
+ */
+void pci_pme_wakeup_bus(struct pci_bus *bus)
+{
+	if (bus)
+		pci_walk_bus(bus, pci_pme_wakeup, NULL);
+}
+
+/**
  * pci_pme_capable - check the capability of PCI device to generate PME#
  * @dev: PCI device to handle.
  * @state: PCI state from which device will issue PME#.
@@ -1434,6 +1466,41 @@ int pci_back_from_sleep(struct pci_dev *
 }
 
 /**
+ * pci_dev_run_wake - Check if device can generate run-time wake-up events.
+ * @dev: Device to check.
+ *
+ * Return true if the device itself is cabable of generating wake-up events
+ * (through the platform or using the native PCIe PME) or if the device supports
+ * PME and one of its upstream bridges can generate wake-up events.
+ */
+bool pci_dev_run_wake(struct pci_dev *dev)
+{
+	struct pci_bus *bus = dev->bus;
+
+	if (device_run_wake(&dev->dev))
+		return true;
+
+	if (!dev->pme_support)
+		return false;
+
+	while (bus->parent) {
+		struct pci_dev *bridge = bus->self;
+
+		if (device_run_wake(&bridge->dev))
+			return true;
+
+		bus = bus->parent;
+	}
+
+	/* We have reached the root bus. */
+	if (bus->bridge)
+		return device_run_wake(bus->bridge);
+
+	return false;
+}
+EXPORT_SYMBOL_GPL(pci_dev_run_wake);
+
+/**
  * pci_pm_init - Initialize PM functions of given PCI device
  * @dev: PCI device to handle.
  */
Index: linux-2.6/include/linux/pci.h
===================================================================
--- linux-2.6.orig/include/linux/pci.h
+++ linux-2.6/include/linux/pci.h
@@ -756,6 +756,7 @@ int pci_wake_from_d3(struct pci_dev *dev
 pci_power_t pci_target_state(struct pci_dev *dev);
 int pci_prepare_to_sleep(struct pci_dev *dev);
 int pci_back_from_sleep(struct pci_dev *dev);
+bool pci_dev_run_wake(struct pci_dev *dev);
 
 /* For use by arch with custom probe code */
 void set_pcie_port_type(struct pci_dev *pdev);
Index: linux-2.6/include/linux/pci-acpi.h
===================================================================
--- linux-2.6.orig/include/linux/pci-acpi.h
+++ linux-2.6/include/linux/pci-acpi.h
@@ -11,6 +11,13 @@
 #include <linux/acpi.h>
 
 #ifdef CONFIG_ACPI
+extern acpi_status pci_acpi_add_bus_pm_notifier(struct acpi_device *dev,
+						 struct pci_bus *pci_bus);
+extern acpi_status pci_acpi_remove_bus_pm_notifier(struct acpi_device *dev);
+extern acpi_status pci_acpi_add_pm_notifier(struct acpi_device *dev,
+					     struct pci_dev *pci_dev);
+extern acpi_status pci_acpi_remove_pm_notifier(struct acpi_device *dev);
+
 static inline acpi_handle acpi_find_root_bridge_handle(struct pci_dev *pdev)
 {
 	struct pci_bus *pbus = pdev->bus;
Index: linux-2.6/include/acpi/acpi_bus.h
===================================================================
--- linux-2.6.orig/include/acpi/acpi_bus.h
+++ linux-2.6/include/acpi/acpi_bus.h
@@ -243,6 +243,7 @@ struct acpi_device_wakeup_flags {
 	u8 valid:1;		/* Can successfully enable wakeup? */
 	u8 run_wake:1;		/* Run-Wake GPE devices */
 	u8 always_enabled:1;	/* Run-wake devices that are always enabled */
+	u8 notifier_present:1;  /* Wake-up notify handler has been installed */
 };
 
 struct acpi_device_wakeup_state {
@@ -388,6 +389,9 @@ acpi_handle acpi_get_pci_rootbridge_hand
 struct acpi_pci_root *acpi_pci_find_root(acpi_handle handle);
 #define DEVICE_ACPI_HANDLE(dev) ((acpi_handle)((dev)->archdata.acpi_handle))
 
+int acpi_enable_wakeup_device_power(struct acpi_device *dev, int state);
+int acpi_disable_wakeup_device_power(struct acpi_device *dev);
+
 #ifdef CONFIG_PM_SLEEP
 int acpi_pm_device_sleep_state(struct device *, int *);
 int acpi_pm_device_sleep_wake(struct device *, bool);
Index: linux-2.6/drivers/acpi/internal.h
===================================================================
--- linux-2.6.orig/drivers/acpi/internal.h
+++ linux-2.6/drivers/acpi/internal.h
@@ -36,8 +36,6 @@ static inline int acpi_debug_init(void) 
 int acpi_power_init(void);
 int acpi_device_sleep_wake(struct acpi_device *dev,
                            int enable, int sleep_state, int dev_state);
-int acpi_enable_wakeup_device_power(struct acpi_device *dev, int sleep_state);
-int acpi_disable_wakeup_device_power(struct acpi_device *dev);
 int acpi_power_get_inferred_state(struct acpi_device *device);
 int acpi_power_transition(struct acpi_device *device, int state);
 extern int acpi_power_nocheck;
Index: linux-2.6/drivers/acpi/scan.c
===================================================================
--- linux-2.6.orig/drivers/acpi/scan.c
+++ linux-2.6/drivers/acpi/scan.c
@@ -753,6 +753,7 @@ static void acpi_bus_set_run_wake_flags(
 	acpi_event_status event_status;
 
 	device->wakeup.run_wake_count = 0;
+	device->wakeup.flags.notifier_present = 0;
 
 	/* Power button, Lid switch always enable wakeup */
 	if (!acpi_match_device_ids(device, button_device_ids)) {
Index: linux-2.6/drivers/acpi/pci_root.c
===================================================================
--- linux-2.6.orig/drivers/acpi/pci_root.c
+++ linux-2.6/drivers/acpi/pci_root.c
@@ -30,6 +30,7 @@
 #include <linux/proc_fs.h>
 #include <linux/spinlock.h>
 #include <linux/pm.h>
+#include <linux/pm_runtime.h>
 #include <linux/pci.h>
 #include <linux/pci-acpi.h>
 #include <linux/acpi.h>
@@ -528,6 +529,10 @@ static int __devinit acpi_pci_root_add(s
 	if (flags != base_flags)
 		acpi_pci_osc_support(root, flags);
 
+	pci_acpi_add_bus_pm_notifier(device, root->bus);
+	if (device->wakeup.flags.run_wake)
+		device_set_run_wake(root->bus->bridge, true);
+
 	return 0;
 
 end:
@@ -549,6 +554,9 @@ static int acpi_pci_root_remove(struct a
 {
 	struct acpi_pci_root *root = acpi_driver_data(device);
 
+	device_set_run_wake(root->bus->bridge, false);
+	pci_acpi_remove_bus_pm_notifier(device);
+
 	kfree(root);
 	return 0;
 }
Index: linux-2.6/drivers/acpi/pci_bind.c
===================================================================
--- linux-2.6.orig/drivers/acpi/pci_bind.c
+++ linux-2.6/drivers/acpi/pci_bind.c
@@ -26,7 +26,9 @@
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/pci.h>
+#include <linux/pci-acpi.h>
 #include <linux/acpi.h>
+#include <linux/pm_runtime.h>
 #include <acpi/acpi_bus.h>
 #include <acpi/acpi_drivers.h>
 
@@ -38,7 +40,13 @@ static int acpi_pci_unbind(struct acpi_d
 	struct pci_dev *dev;
 
 	dev = acpi_get_pci_dev(device->handle);
-	if (!dev || !dev->subordinate)
+	if (!dev)
+		goto out;
+
+	device_set_run_wake(&dev->dev, false);
+	pci_acpi_remove_pm_notifier(device);
+
+	if (!dev->subordinate)
 		goto out;
 
 	acpi_pci_irq_del_prt(dev->subordinate);
@@ -62,6 +70,10 @@ static int acpi_pci_bind(struct acpi_dev
 	if (!dev)
 		return 0;
 
+	pci_acpi_add_pm_notifier(device, dev);
+	if (device->wakeup.flags.run_wake)
+		device_set_run_wake(&dev->dev, true);
+
 	/*
 	 * Install the 'bind' function to facilitate callbacks for
 	 * children of the P2P bridge.

[PATCH 8/8] PCI PM: Run-time callbacks for PCI bus type (rev. 2)

[Rafael J. Wysocki]

From: Rafael J. Wysocki <rjw@sisk.pl>

Introduce run-time PM callbacks for the PCI bus type.  Make the new
callbacks work in analogy with the existing system sleep PM
callbacks, so that the drivers already converted to struct dev_pm_ops
can use their suspend and resume routines for run-time PM without
modifications.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
---
 drivers/pci/pci-driver.c |  160 +++++++++++++++++++++++++++++++++++++++--------
 drivers/pci/pci.c        |   43 ++++++++++--
 drivers/pci/pci.h        |    1 
 include/linux/pci.h      |    9 ++
 kernel/power/Kconfig     |    5 +
 5 files changed, 184 insertions(+), 34 deletions(-)

Index: linux-2.6/kernel/power/Kconfig
===================================================================
--- linux-2.6.orig/kernel/power/Kconfig
+++ linux-2.6/kernel/power/Kconfig
@@ -222,3 +222,8 @@ config PM_RUNTIME
 	  and the bus type drivers of the buses the devices are on are
 	  responsible for the actual handling of the autosuspend requests and
 	  wake-up events.
+
+config PM_OPS
+	bool
+	depends on PM_SLEEP || PM_RUNTIME
+	default y
Index: linux-2.6/drivers/pci/pci-driver.c
===================================================================
--- linux-2.6.orig/drivers/pci/pci-driver.c
+++ linux-2.6/drivers/pci/pci-driver.c
@@ -17,6 +17,7 @@
 #include <linux/slab.h>
 #include <linux/sched.h>
 #include <linux/cpu.h>
+#include <linux/pm_runtime.h>
 #include "pci.h"
 
 struct pci_dynid {
@@ -404,6 +405,35 @@ static void pci_device_shutdown(struct d
 	pci_msix_shutdown(pci_dev);
 }
 
+#ifdef CONFIG_PM_OPS
+
+/* Auxiliary functions used for system resume and run-time resume. */
+
+/**
+ * pci_restore_standard_config - restore standard config registers of PCI device
+ * @pci_dev: PCI device to handle
+ */
+static int pci_restore_standard_config(struct pci_dev *pci_dev)
+{
+	pci_update_current_state(pci_dev, PCI_UNKNOWN);
+
+	if (pci_dev->current_state != PCI_D0) {
+		int error = pci_set_power_state(pci_dev, PCI_D0);
+		if (error)
+			return error;
+	}
+
+	return pci_restore_state(pci_dev);
+}
+
+static void pci_pm_default_resume_early(struct pci_dev *pci_dev)
+{
+	pci_restore_standard_config(pci_dev);
+	pci_fixup_device(pci_fixup_resume_early, pci_dev);
+}
+
+#endif
+
 #ifdef CONFIG_PM_SLEEP
 
 /*
@@ -520,29 +550,6 @@ static int pci_legacy_resume(struct devi
 
 /* Auxiliary functions used by the new power management framework */
 
-/**
- * pci_restore_standard_config - restore standard config registers of PCI device
- * @pci_dev: PCI device to handle
- */
-static int pci_restore_standard_config(struct pci_dev *pci_dev)
-{
-	pci_update_current_state(pci_dev, PCI_UNKNOWN);
-
-	if (pci_dev->current_state != PCI_D0) {
-		int error = pci_set_power_state(pci_dev, PCI_D0);
-		if (error)
-			return error;
-	}
-
-	return pci_restore_state(pci_dev);
-}
-
-static void pci_pm_default_resume_noirq(struct pci_dev *pci_dev)
-{
-	pci_restore_standard_config(pci_dev);
-	pci_fixup_device(pci_fixup_resume_early, pci_dev);
-}
-
 static void pci_pm_default_resume(struct pci_dev *pci_dev)
 {
 	pci_fixup_device(pci_fixup_resume, pci_dev);
@@ -581,6 +588,17 @@ static int pci_pm_prepare(struct device 
 	struct device_driver *drv = dev->driver;
 	int error = 0;
 
+	/*
+	 * PCI devices suspended at run time need to be resumed at this
+	 * point, because in general it is necessary to reconfigure them for
+	 * system suspend.  Namely, if the device is supposed to wake up the
+	 * system from the sleep state, we may need to reconfigure it for this
+	 * purpose.  In turn, if the device is not supposed to wake up the
+	 * system from the sleep state, we'll have to prevent it from signaling
+	 * wake-up.
+	 */
+	pm_runtime_resume(dev);
+
 	if (drv && drv->pm && drv->pm->prepare)
 		error = drv->pm->prepare(dev);
 
@@ -595,6 +613,13 @@ static void pci_pm_complete(struct devic
 		drv->pm->complete(dev);
 }
 
+#else /* !CONFIG_PM_SLEEP */
+
+#define pci_pm_prepare	NULL
+#define pci_pm_complete	NULL
+
+#endif /* !CONFIG_PM_SLEEP */
+
 #ifdef CONFIG_SUSPEND
 
 static int pci_pm_suspend(struct device *dev)
@@ -681,7 +706,7 @@ static int pci_pm_resume_noirq(struct de
 	struct device_driver *drv = dev->driver;
 	int error = 0;
 
-	pci_pm_default_resume_noirq(pci_dev);
+	pci_pm_default_resume_early(pci_dev);
 
 	if (pci_has_legacy_pm_support(pci_dev))
 		return pci_legacy_resume_early(dev);
@@ -879,7 +904,7 @@ static int pci_pm_restore_noirq(struct d
 	struct device_driver *drv = dev->driver;
 	int error = 0;
 
-	pci_pm_default_resume_noirq(pci_dev);
+	pci_pm_default_resume_early(pci_dev);
 
 	if (pci_has_legacy_pm_support(pci_dev))
 		return pci_legacy_resume_early(dev);
@@ -931,6 +956,84 @@ static int pci_pm_restore(struct device 
 
 #endif /* !CONFIG_HIBERNATION */
 
+#ifdef CONFIG_PM_RUNTIME
+
+static int pci_pm_runtime_suspend(struct device *dev)
+{
+	struct pci_dev *pci_dev = to_pci_dev(dev);
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+	pci_power_t prev = pci_dev->current_state;
+	int error;
+
+	if (!pm || !pm->runtime_suspend)
+		return -ENOSYS;
+
+	error = pm->runtime_suspend(dev);
+	suspend_report_result(pm->runtime_suspend, error);
+	if (error)
+		return error;
+
+	pci_fixup_device(pci_fixup_suspend, pci_dev);
+
+	if (!pci_dev->state_saved && pci_dev->current_state != PCI_D0
+	    && pci_dev->current_state != PCI_UNKNOWN) {
+		WARN_ONCE(pci_dev->current_state != prev,
+			"PCI PM: State of device not saved by %pF\n",
+			pm->runtime_suspend);
+		return 0;
+	}
+
+	if (!pci_dev->state_saved)
+		pci_save_state(pci_dev);
+
+	pci_finish_runtime_suspend(pci_dev);
+
+	return 0;
+}
+
+static int pci_pm_runtime_resume(struct device *dev)
+{
+	struct pci_dev *pci_dev = to_pci_dev(dev);
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+
+	if (!pm || !pm->runtime_resume)
+		return -ENOSYS;
+
+	pci_pm_default_resume_early(pci_dev);
+	__pci_enable_wake(pci_dev, PCI_D0, true, false);
+	pci_fixup_device(pci_fixup_resume, pci_dev);
+
+	return pm->runtime_resume(dev);
+}
+
+static int pci_pm_runtime_idle(struct device *dev)
+{
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+
+	if (!pm)
+		return -ENOSYS;
+
+	if (pm->runtime_idle) {
+		int ret = pm->runtime_idle(dev);
+		if (ret)
+			return ret;
+	}
+
+	pm_runtime_suspend(dev);
+
+	return 0;
+}
+
+#else /* !CONFIG_PM_RUNTIME */
+
+#define pci_pm_runtime_suspend	NULL
+#define pci_pm_runtime_resume	NULL
+#define pci_pm_runtime_idle	NULL
+
+#endif /* !CONFIG_PM_RUNTIME */
+
+#ifdef CONFIG_PM_OPS
+
 const struct dev_pm_ops pci_dev_pm_ops = {
 	.prepare = pci_pm_prepare,
 	.complete = pci_pm_complete,
@@ -946,15 +1049,18 @@ const struct dev_pm_ops pci_dev_pm_ops =
 	.thaw_noirq = pci_pm_thaw_noirq,
 	.poweroff_noirq = pci_pm_poweroff_noirq,
 	.restore_noirq = pci_pm_restore_noirq,
+	.runtime_suspend = pci_pm_runtime_suspend,
+	.runtime_resume = pci_pm_runtime_resume,
+	.runtime_idle = pci_pm_runtime_idle,
 };
 
 #define PCI_PM_OPS_PTR	(&pci_dev_pm_ops)
 
-#else /* !CONFIG_PM_SLEEP */
+#else /* !COMFIG_PM_OPS */
 
 #define PCI_PM_OPS_PTR	NULL
 
-#endif /* !CONFIG_PM_SLEEP */
+#endif /* !COMFIG_PM_OPS */
 
 /**
  * __pci_register_driver - register a new pci driver
Index: linux-2.6/drivers/pci/pci.c
===================================================================
--- linux-2.6.orig/drivers/pci/pci.c
+++ linux-2.6/drivers/pci/pci.c
@@ -1302,9 +1302,10 @@ void pci_pme_active(struct pci_dev *dev,
 }
 
 /**
- * pci_enable_wake - enable PCI device as wakeup event source
+ * __pci_enable_wake - enable PCI device as wakeup event source
  * @dev: PCI device affected
  * @state: PCI state from which device will issue wakeup events
+ * @runtime: True if the events are to be generated at run time
  * @enable: True to enable event generation; false to disable
  *
  * This enables the device as a wakeup event source, or disables it.
@@ -1320,11 +1321,12 @@ void pci_pme_active(struct pci_dev *dev,
  * Error code depending on the platform is returned if both the platform and
  * the native mechanism fail to enable the generation of wake-up events
  */
-int pci_enable_wake(struct pci_dev *dev, pci_power_t state, bool enable)
+int __pci_enable_wake(struct pci_dev *dev, pci_power_t state,
+		      bool runtime, bool enable)
 {
 	int ret = 0;
 
-	if (enable && !device_may_wakeup(&dev->dev))
+	if (enable && !runtime && !device_may_wakeup(&dev->dev))
 		return -EINVAL;
 
 	/* Don't do the same thing twice in a row for one device. */
@@ -1344,19 +1346,24 @@ int pci_enable_wake(struct pci_dev *dev,
 			pci_pme_active(dev, true);
 		else
 			ret = 1;
-		error = platform_pci_sleep_wake(dev, true);
+		error = runtime ? platform_pci_run_wake(dev, true) :
+					platform_pci_sleep_wake(dev, true);
 		if (ret)
 			ret = error;
 		if (!ret)
 			dev->wakeup_prepared = true;
 	} else {
-		platform_pci_sleep_wake(dev, false);
+		if (runtime)
+			platform_pci_run_wake(dev, false);
+		else
+			platform_pci_sleep_wake(dev, false);
 		pci_pme_active(dev, false);
 		dev->wakeup_prepared = false;
 	}
 
 	return ret;
 }
+EXPORT_SYMBOL(__pci_enable_wake);
 
 /**
  * pci_wake_from_d3 - enable/disable device to wake up from D3_hot or D3_cold
@@ -1466,6 +1473,31 @@ int pci_back_from_sleep(struct pci_dev *
 }
 
 /**
+ * pci_finish_runtime_suspend - Carry out PCI-specific part of runtime suspend.
+ * @dev: PCI device being suspended.
+ *
+ * Prepare @dev to generate wake-up events at run time and put it into a low
+ * power state.
+ */
+int pci_finish_runtime_suspend(struct pci_dev *dev)
+{
+	pci_power_t target_state = pci_target_state(dev);
+	int error;
+
+	if (target_state == PCI_POWER_ERROR)
+		return -EIO;
+
+	__pci_enable_wake(dev, target_state, true, pci_dev_run_wake(dev));
+
+	error = pci_set_power_state(dev, target_state);
+
+	if (error)
+		__pci_enable_wake(dev, target_state, true, false);
+
+	return error;
+}
+
+/**
  * pci_dev_run_wake - Check if device can generate run-time wake-up events.
  * @dev: Device to check.
  *
@@ -2978,7 +3010,6 @@ EXPORT_SYMBOL(pci_save_state);
 EXPORT_SYMBOL(pci_restore_state);
 EXPORT_SYMBOL(pci_pme_capable);
 EXPORT_SYMBOL(pci_pme_active);
-EXPORT_SYMBOL(pci_enable_wake);
 EXPORT_SYMBOL(pci_wake_from_d3);
 EXPORT_SYMBOL(pci_target_state);
 EXPORT_SYMBOL(pci_prepare_to_sleep);
Index: linux-2.6/include/linux/pci.h
===================================================================
--- linux-2.6.orig/include/linux/pci.h
+++ linux-2.6/include/linux/pci.h
@@ -751,13 +751,20 @@ int pci_set_power_state(struct pci_dev *
 pci_power_t pci_choose_state(struct pci_dev *dev, pm_message_t state);
 bool pci_pme_capable(struct pci_dev *dev, pci_power_t state);
 void pci_pme_active(struct pci_dev *dev, bool enable);
-int pci_enable_wake(struct pci_dev *dev, pci_power_t state, bool enable);
+int __pci_enable_wake(struct pci_dev *dev, pci_power_t state,
+		      bool runtime, bool enable);
 int pci_wake_from_d3(struct pci_dev *dev, bool enable);
 pci_power_t pci_target_state(struct pci_dev *dev);
 int pci_prepare_to_sleep(struct pci_dev *dev);
 int pci_back_from_sleep(struct pci_dev *dev);
 bool pci_dev_run_wake(struct pci_dev *dev);
 
+static inline int pci_enable_wake(struct pci_dev *dev, pci_power_t state,
+				  bool enable)
+{
+	return __pci_enable_wake(dev, state, false, enable);
+}
+
 /* For use by arch with custom probe code */
 void set_pcie_port_type(struct pci_dev *pdev);
 void set_pcie_hotplug_bridge(struct pci_dev *pdev);
Index: linux-2.6/drivers/pci/pci.h
===================================================================
--- linux-2.6.orig/drivers/pci/pci.h
+++ linux-2.6/drivers/pci/pci.h
@@ -55,6 +55,7 @@ extern int pci_set_platform_pm(struct pc
 extern void pci_update_current_state(struct pci_dev *dev, pci_power_t state);
 extern void pci_disable_enabled_device(struct pci_dev *dev);
 extern bool pci_check_pme_status(struct pci_dev *dev);
+extern int pci_finish_runtime_suspend(struct pci_dev *dev);
 extern int __pci_pme_wakeup(struct pci_dev *dev, void *ign);
 extern void pci_pme_wakeup_bus(struct pci_bus *bus);
 extern void pci_pm_init(struct pci_dev *dev);

Re: [PATCH 4/8] ACPI: Use GPE reference counting to support shared GPEs

[Jin Dongming]

Hi, Rafael J. Wysocki
> -	/* Update enable mask, but don't enable the HW GPE as of yet */
> -
> -	status = acpi_ev_enable_gpe(gpe_event_info, FALSE);
I think the above line code should be remained. If it is deleted, the exception 
event will be raised on some machine.

Best Regards,
Jin Dongming
> -
>  	ACPI_DEBUG_PRINT((ACPI_DB_LOAD,
>  			  "Registered GPE method %s as GPE number 0x%.2X\n",
>  			  name, gpe_number));
> -	return_ACPI_STATUS(status);
> +	return_ACPI_STATUS(AE_OK);
>  }
>  

Re: [PATCH 4/8] ACPI: Use GPE reference counting to support shared GPEs

[Rafael J. Wysocki]

On Thursday 18 February 2010, Jin Dongming wrote:
> Hi, Rafael J. Wysocki
> > -	/* Update enable mask, but don't enable the HW GPE as of yet */
> > -
> > -	status = acpi_ev_enable_gpe(gpe_event_info, FALSE);

You could preserve some more context.

> I think the above line code should be remained. If it is deleted, the exception 
> event will be raised on some machine.

Why would it?  The GPE is still disabled at the hardware level at this point.

Rafael

Re: [PATCH 4/8] ACPI: Use GPE reference counting to support shared GPEs

[Jin Dongming]

Hi, Rafael J. Wysocki

Rafael J. Wysocki wrote:
> On Thursday 18 February 2010, Jin Dongming wrote:
>> Hi, Rafael J. Wysocki
>>> -	/* Update enable mask, but don't enable the HW GPE as of yet */
>>> -
>>> -	status = acpi_ev_enable_gpe(gpe_event_info, FALSE);
> 
> You could preserve some more context.
> 
>> I think the above line code should be remained. If it is deleted, the exception 
>> event will be raised on some machine.
> 
> Why would it?  The GPE is still disabled at the hardware level at this point.
> 
> Rafael
> 
> 
I am very sorry for my wrong comment. The GPE is still disabled as you wrote.

The error message what I got was not caused by GPE event, it was caused by the "status"
variable which had not been deleted on x86-next tree. And it is also deleted at this
file. So I don't there is problem here.

Best regards,
Jin Dongming

Re: [PATCH 4/8] ACPI: Use GPE reference counting to support shared GPEs

[Rafael J. Wysocki]

On Friday 19 February 2010, Jin Dongming wrote:
> Hi, Rafael J. Wysocki
> 
> Rafael J. Wysocki wrote:
> > On Thursday 18 February 2010, Jin Dongming wrote:
> >> Hi, Rafael J. Wysocki
> >>> -	/* Update enable mask, but don't enable the HW GPE as of yet */
> >>> -
> >>> -	status = acpi_ev_enable_gpe(gpe_event_info, FALSE);
> > 
> > You could preserve some more context.
> > 
> >> I think the above line code should be remained. If it is deleted, the exception 
> >> event will be raised on some machine.
> > 
> > Why would it?  The GPE is still disabled at the hardware level at this point.
> > 
> > Rafael
> > 
> > 
> I am very sorry for my wrong comment. The GPE is still disabled as you wrote.
> 
> The error message what I got was not caused by GPE event, it was caused by the "status"
> variable which had not been deleted on x86-next tree. And it is also deleted at this
> file. So I don't there is problem here.

Great, thanks for the review.

Rafael

Re: [PATCH 1/8] PCI PM: Add function for checking PME status of devices

[Jesse Barnes]

On Wed, 17 Feb 2010 23:36:58 +0100
"Rafael J. Wysocki" <rjw@sisk.pl> wrote:

> From: Rafael J. Wysocki <rjw@sisk.pl>
> 
> Add function pci_check_pme_status() that will check the PME status
> bit of given device and clear it along with the PME enable bit.  It
> will be necessary for PCI run-time power management.
> 
> Based on a patch from Shaohua Li <shaohua.li@intel.com>
> 
> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
> ---

Applied this series and dropped the old patches, thanks Rafael.

-- 
Jesse Barnes, Intel Open Source Technology Center

Re: [PATCH 1/8] PCI PM: Add function for checking PME status of devices

[Rafael J. Wysocki]

On Tuesday 23 February 2010, Jesse Barnes wrote:
> On Wed, 17 Feb 2010 23:36:58 +0100
> "Rafael J. Wysocki" <rjw@sisk.pl> wrote:
> 
> > From: Rafael J. Wysocki <rjw@sisk.pl>
> > 
> > Add function pci_check_pme_status() that will check the PME status
> > bit of given device and clear it along with the PME enable bit.  It
> > will be necessary for PCI run-time power management.
> > 
> > Based on a patch from Shaohua Li <shaohua.li@intel.com>
> > 
> > Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
> > ---
> 
> Applied this series and dropped the old patches, thanks Rafael.

Great, thanks Jesse.