From: Leo Yan <leo.yan@linaro.org>
To: Steve Muckle <steve.muckle@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>,
Ingo Molnar <mingo@redhat.com>,
linux-kernel@vger.kernel.org, linux-pm@vger.kernel.org,
Vincent Guittot <vincent.guittot@linaro.org>,
Morten Rasmussen <morten.rasmussen@arm.com>,
Dietmar Eggemann <dietmar.eggemann@arm.com>,
Juri Lelli <Juri.Lelli@arm.com>,
Patrick Bellasi <patrick.bellasi@arm.com>,
Michael Turquette <mturquette@baylibre.com>,
Ricky Liang <jcliang@chromium.org>
Subject: Re: [RFCv6 PATCH 03/10] sched: scheduler-driven cpu frequency selection
Date: Sat, 19 Dec 2015 13:54:32 +0800 [thread overview]
Message-ID: <20151219055432.GB23305@leoy-linaro> (raw)
In-Reply-To: <56745B35.5050704@linaro.org>
Hi Steve,
On Fri, Dec 18, 2015 at 11:15:01AM -0800, Steve Muckle wrote:
> On 12/16/2015 11:17 PM, Leo Yan wrote:
> > Could you check if below corner case will introduce logic error?
> > The task still will be removed from rq if timer tick is triggered
> > between two time's set_current_state().
> >
> > set_current_state(TASK_INTERRUPTIBLE);
> > `-------> timer_tick and
> > schedule();
> > do_something...
> > set_current_state(TASK_RUNNING);
> >
> > It will be safe for combination for set_current_state()/schedule()
> > with waken_up_process():
> >
> > Thread_A: Thread_B:
> >
> > set_current_state(TASK_INTERRUPTIBLE);
> > `-------> timer_tick and
> > schedule();
> > ....
> > wake_up_process(Thread_A);
> > <---------------------/
> > schedule();
> >
> > The first time's schedule() will remove task from rq which is caused
> > by timer tick and call schedule(), and the second time schdule() will
> > be equal yeild().
>
> I was initially concerned about preemption while task state =
> TASK_INTERRUPTIBLE as well, but a task with state TASK_INTERRUPTIBLE is
> not dequeued if it is preempted. See core.c:__schedule():
>
> if (!preempt && prev->state) {
> if (unlikely(signal_pending_state(prev->state, prev))) {
> prev->state = TASK_RUNNING;
> } else {
> deactivate_task(rq, prev, DEQUEUE_SLEEP);
> prev->on_rq = 0;
>
> I knew this had to be the case, because this design pattern is used in
> many other places in the kernel, so many things would be very broken if
> this were a problem.
You are right, I went through the code again and sched tick irq will
call preempt_schedule_irq() and __schedule(true); so finally set the
parameter "preempt" = true. Sorry for noise :p
---8<---
arch/arm64/kernel/entry.S:
#ifdef CONFIG_PREEMPT
el1_preempt:
mov x24, lr
1: bl preempt_schedule_irq // irq en/disable is done inside
ldr x0, [tsk, #TI_FLAGS] // get new tasks TI_FLAGS
tbnz x0, #TIF_NEED_RESCHED, 1b // needs rescheduling?
ret x24
#endif
Thanks,
Leo Yan
next prev parent reply other threads:[~2015-12-19 5:54 UTC|newest]
Thread overview: 59+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-12-09 6:19 [RFCv6 PATCH 00/10] sched: scheduler-driven CPU frequency selection Steve Muckle
2015-12-09 6:19 ` [RFCv6 PATCH 01/10] sched: Compute cpu capacity available at current frequency Steve Muckle
2015-12-09 6:19 ` [RFCv6 PATCH 02/10] cpufreq: introduce cpufreq_driver_is_slow Steve Muckle
2015-12-09 6:19 ` [RFCv6 PATCH 03/10] sched: scheduler-driven cpu frequency selection Steve Muckle
2015-12-11 11:04 ` Juri Lelli
2015-12-15 2:02 ` Steve Muckle
2015-12-15 10:31 ` Juri Lelli
2015-12-16 1:22 ` Steve Muckle
2015-12-16 3:48 ` Leo Yan
2015-12-17 1:24 ` Steve Muckle
2015-12-17 7:17 ` Leo Yan
2015-12-18 19:15 ` Steve Muckle
2015-12-19 5:54 ` Leo Yan [this message]
2016-01-25 12:06 ` Ricky Liang
2016-01-27 1:14 ` Steve Muckle
2016-02-01 17:10 ` Ricky Liang
2016-02-11 4:44 ` Steve Muckle
2015-12-09 6:19 ` [RFCv6 PATCH 04/10] sched/fair: add triggers for OPP change requests Steve Muckle
2015-12-09 6:19 ` [RFCv6 PATCH 05/10] sched/{core,fair}: trigger OPP change request on fork() Steve Muckle
2015-12-09 6:19 ` [RFCv6 PATCH 06/10] sched/fair: cpufreq_sched triggers for load balancing Steve Muckle
2015-12-09 6:19 ` [RFCv6 PATCH 07/10] sched/fair: jump to max OPP when crossing UP threshold Steve Muckle
2015-12-11 11:12 ` Juri Lelli
2015-12-15 2:42 ` Steve Muckle
2015-12-09 6:19 ` [RFCv6 PATCH 08/10] sched: remove call of sched_avg_update from sched_rt_avg_update Steve Muckle
2015-12-09 6:19 ` [RFCv6 PATCH 09/10] sched: deadline: use deadline bandwidth in scale_rt_capacity Steve Muckle
2015-12-09 8:50 ` Vincent Guittot
2015-12-10 13:27 ` Luca Abeni
2015-12-10 16:11 ` Vincent Guittot
2015-12-11 7:48 ` Luca Abeni
2015-12-14 14:02 ` Vincent Guittot
2015-12-14 14:38 ` Luca Abeni
2015-12-14 15:17 ` Peter Zijlstra
2015-12-14 15:56 ` Vincent Guittot
2015-12-14 16:07 ` Juri Lelli
2015-12-14 21:19 ` Luca Abeni
2015-12-14 16:51 ` Peter Zijlstra
2015-12-14 21:31 ` Luca Abeni
2015-12-15 12:38 ` Peter Zijlstra
2015-12-15 13:30 ` Luca Abeni
2015-12-15 13:42 ` Peter Zijlstra
2015-12-15 21:24 ` Luca Abeni
2015-12-16 9:28 ` Juri Lelli
2015-12-15 4:43 ` Vincent Guittot
2015-12-15 12:41 ` Peter Zijlstra
2015-12-15 12:56 ` Vincent Guittot
2015-12-14 21:12 ` Luca Abeni
2015-12-15 4:59 ` Vincent Guittot
2015-12-15 8:50 ` Luca Abeni
2015-12-15 12:20 ` Peter Zijlstra
2015-12-15 12:46 ` Vincent Guittot
2015-12-15 13:18 ` Luca Abeni
2015-12-15 12:23 ` Peter Zijlstra
2015-12-15 13:21 ` Luca Abeni
2015-12-15 12:43 ` Vincent Guittot
2015-12-15 13:39 ` Luca Abeni
2015-12-15 12:58 ` Vincent Guittot
2015-12-15 13:41 ` Luca Abeni
2015-12-09 6:19 ` [RFCv6 PATCH 10/10] sched: rt scheduler sets capacity requirement Steve Muckle
2015-12-11 11:22 ` Juri Lelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20151219055432.GB23305@leoy-linaro \
--to=leo.yan@linaro.org \
--cc=Juri.Lelli@arm.com \
--cc=dietmar.eggemann@arm.com \
--cc=jcliang@chromium.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=mingo@redhat.com \
--cc=morten.rasmussen@arm.com \
--cc=mturquette@baylibre.com \
--cc=patrick.bellasi@arm.com \
--cc=peterz@infradead.org \
--cc=steve.muckle@linaro.org \
--cc=vincent.guittot@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox