* Re: Configurazione RAID SOFTWARE su vecchio PC: CONSIGLI
2009-12-13 20:35 Configurazione RAID SOFTWARE su vecchio PC: CONSIGLI mig81
2009-12-13 20:39 ` mig81
@ 2009-12-13 20:53 ` Michał Przyłuski
2009-12-13 21:11 ` mig81
2009-12-14 7:37 ` Luca Berra
3 siblings, 0 replies; 6+ messages in thread
From: Michał Przyłuski @ 2009-12-13 20:53 UTC (permalink / raw)
To: mig81; +Cc: linux-raid
Ciao mig81,
2009/12/13 mig81 <fluxus@sonicurbs.com>:
>
> Ciao a tutti
> ...
I stronly suggest using English, that way you could get more replies.
Now, from what I understood (mostly through google translate).
I recall that AHA-2940U has just 1 SCSI channel. So it doesn't matter
if both disks are inside, or one is in, and the other is out. That
means you can totally stay with your current, all internal, setup.
As for the 2nd question, I don't quite understand it (my Italian is
totally rusty), but if you want to use the IDE harddisk as boot drive,
and just store some data on that 2*SCSI software raid, I recommend
putting bootloader on the IDE drive.
However, be warned, that RH 7.0 does not use the md driver which is
this list about. It's using the old "raidtools" package (or at least I
suppose so, since my RH 7.2 has
raidtools-0.90 installed).
Saluti,
Mike
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Configurazione RAID SOFTWARE su vecchio PC: CONSIGLI
2009-12-13 20:35 Configurazione RAID SOFTWARE su vecchio PC: CONSIGLI mig81
` (2 preceding siblings ...)
2009-12-13 21:11 ` mig81
@ 2009-12-14 7:37 ` Luca Berra
3 siblings, 0 replies; 6+ messages in thread
From: Luca Berra @ 2009-12-14 7:37 UTC (permalink / raw)
To: linux-raid
Sorry for italian here, english translation at bottom
Prima di tutto, come ti hanno gia' fatto notare, scrivere in italiano qui
e' stato scortese, la prossima volta prima di buttarti a pesce dai un
occhiata agli archivi...
On Sun, Dec 13, 2009 at 12:35:39PM -0800, mig81 wrote:
>Ciao a tutti, mi sono appena iscritto su questo forum per chiedervi un
>consiglio riguardo la configurazione di un Pentium PRO 166 MHz con 64 Mb di
>RAM un controller SCSI Adaptech AHA-2940U con collegati 2 HD Viking SCSI da
>4,5 Gb l'uno ed un CD-ROM SCSI. HD Maxtor 80 Gb su IDE ATA-133, lettore
>floppy
bel pezzo da museo, immagino tu abbia gia' valutato l'opzione di
rottamare il tutto....
>Il controller SCSI non permette di creare un RAID hardware e quindi devo
>optare per uno software.
>Ho una RED HAT 7.0 che permette di costruire un array software e quindi di
>fare un RAID 0/1/5 in fase di installazione.
>
>Anzi tutto vorrei sapere come è più opportuno collegare i 2 HD SCSI: uno lo
>collego alla piattina interna del controller e l'altro HD sulla piattina
>esterna, anzichè entrambi sulla stessa piattina come li ho sempre avuti,
>giusto?
lasciali sulla piattina interna, in ogni caso e' sempre lo stesso canale
e cosi' ti risparmi un terminatore e un cavo.
>Poi, qunado costruisco il file system come mi conviene suddividere gli hard
>disk? mi conviene creare la /home su quello IDE da 80 Gb? il boot loader
dipende da quanto spazio hai bisogno per la home, in linea di massima
si.
>credo debba installarlo su l'HD da 80 Gb perchè il bios se rileva l'HD sul
>IDE cerca automaticamnete il bootloader su di quello e se non lo trova non
>parte.....
a meno di non disabilitare il riconoscimento degli hard disk dal bios,
linux comunque lo trova lo stesso.
>Avete consigli utili? Anzichè una vecchia REDHAT è meglio che utilizzi un
>altro sistema operativo?
come qualcuno ha gia' detto forse debian supporta ancora quell'hardware
e almeno ci sono ancora gli update. Il problema e' che e' molto diversa
dalla redhat che probabilmente conosci.
In ogni caso io averi qualche remora a creare un raid-0 su dei dischi
cosi' vecchi, se uno dei due si dovesse guastare perdi tutto.
english translation:
(hw description is fairly understandable)
Nice stuff for a museum. i believe you already dismissed the opportunity
to decommission it.
> Scsi controller does not allow making a HW raid, so i have to make a
> software raid.
> I have a Redhat 7, that allows configuring a sw raid during install.
>
> First question is, should i connect the two scsi HDD one on the
> internal scsi port and the other one on the external?
No, you should only use the internal scsi port, it is the same channel
anyway and you save a cable and a terminator.
> How should map the filesystems to the different hard drives? should i
> put /home on the IDE?
It depends on your space requirements, probably yes.
> I believe i should install the boot loader on the IDE drive, since
> bios tries to boot from that one.
You can always disable the drive from the bios. linux does not care.
> do you have any useful hint? would it be better using a different os
> than an old redhat?
As someone already said you can try with a debian, it should support
your old hw and still provide updates. The issue might be that it is
quite different from the redhat system you are probably accustomed to.
In any case i would be wary of creating a raid0 on a couple of very old
disks, if a single one fails you loose all data.
Ciao,
L.
--
Luca Berra -- bluca@comedia.it
Communication Media & Services S.r.l.
/"\
\ / ASCII RIBBON CAMPAIGN
X AGAINST HTML MAIL
/ \
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 6+ messages in thread