Re: [PATCH 8/8] arm64: dts: renesas: hihope-rzg2-ex: Add LVDS panel support

[Laurent Pinchart <laurent.pinchart@ideasonboard.com>]

Hi Biju,

Thank you for the patch.

On Tue, Oct 01, 2019 at 01:15:24PM +0100, Biju Das wrote:
> This patch adds support for Advantech idk-1110wr LVDS panel.
> The HiHope RZ/G2[MN] is advertised as compatible with panel idk-1110wr
> from Advantech, however the panel isn't sold alongside the board.
> 
> Signed-off-by: Biju Das <biju.das@bp.renesas.com>
> ---
>  arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi  | 30 +++++++++++++++++++
>  arch/arm64/boot/dts/renesas/rzg2-panel-lvds.dtsi | 37 ++++++++++++++++++++++++
>  2 files changed, 67 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/renesas/rzg2-panel-lvds.dtsi
> 
> diff --git a/arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi b/arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi
> index 70f9a2a..ae1ef2d 100644
> --- a/arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi
> +++ b/arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi
> @@ -5,6 +5,8 @@
>   * Copyright (C) 2019 Renesas Electronics Corp.
>   */
>  
> +#include "rzg2-panel-lvds.dtsi"
> +
>  / {
>  	aliases {
>  		ethernet0 = &avb;
> @@ -51,6 +53,34 @@
>  	status = "okay";
>  };
>  
> +&gpio1 {
> +	/*
> +	 * When GP1_20 is LOW LVDS0 is connected to the LVDS connector
> +	 * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
> +	 */
> +	lvds-connector-en-gpio {
> +		gpio-hog;
> +		gpios = <20 GPIO_ACTIVE_HIGH>;
> +		output-low;
> +		line-name = "lvds-connector-en-gpio";
> +	};
> +};
> +
> +&lvds0 {
> +	/* Uncomment  below line to enable lvds panel connected to RZ/G2N board
> +	 */
> +
> +	/* status = "okay"; */
> +
> +	ports {
> +		port@1 {
> +			lvds_connector: endpoint {
> +				remote-endpoint = <&panel_in_advantech_idk_1110wr>;
> +			};
> +		};
> +	};
> +};
> +
>  &pciec0 {
>  	status = "okay";
>  };
> diff --git a/arch/arm64/boot/dts/renesas/rzg2-panel-lvds.dtsi b/arch/arm64/boot/dts/renesas/rzg2-panel-lvds.dtsi
> new file mode 100644
> index 0000000..768a8ec
> --- /dev/null
> +++ b/arch/arm64/boot/dts/renesas/rzg2-panel-lvds.dtsi

Should this be named according to the panel name istead of just
"panel-lvds" ? It could be used by any board, and this board could also
use a different LVDS panel.

> @@ -0,0 +1,37 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree Source for the LVDS panels connected to RZ/G2 boards
> + *
> + * Copyright (C) 2019 Renesas Electronics Corp.
> + */
> +
> +/ {
> +
> +	panel-lvds {
> +		compatible = "advantech,idk-1110wr", "panel-lvds";
> +
> +		width-mm = <223>;
> +		height-mm = <125>;
> +
> +		data-mapping = "jeida-24";
> +
> +		panel-timing {
> +			/* 1024x600 @60Hz */
> +			clock-frequency = <51200000>;
> +			hactive = <1024>;
> +			vactive = <600>;
> +			hsync-len = <240>;
> +			hfront-porch = <40>;
> +			hback-porch = <40>;
> +			vfront-porch = <15>;
> +			vback-porch = <10>;
> +			vsync-len = <10>;
> +		};
> +
> +		port {
> +			panel_in_advantech_idk_1110wr: endpoint {

Could we abbreviate the label name to panel_in ? That way the board .dts
wouldn't need to update the remote-endpoint phandle to use a different
panel, only the #include would need to be changed.

> +				remote-endpoint = <&lvds_connector>;
> +			};
> +		};
> +	};
> +};

For the same reason I would set the remote-endpoint for &lvds_connector
here. See arch/arm/boot/dts/r8a77xx-aa104xd12-panel.dtsi for an example.


-- 
Regards,

Laurent Pinchart