Linux-RISC-V Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: Alex Elder <elder@riscstar.com>
To: dlan@gentoo.org, broonie@kernel.org, han.xu@nxp.com
Cc: Frank.li@nxp.com, guodong@riscstar.com,
	linux-spi@vger.kernel.org, imx@lists.linux.dev,
	spacemit@lists.linux.dev, linux-riscv@lists.infradead.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH v4 8/9] riscv: dts: spacemit: enable K1 SoC QSPI on BPI-F3
Date: Mon, 27 Oct 2025 08:30:06 -0500	[thread overview]
Message-ID: <20251027133008.360237-9-elder@riscstar.com> (raw)
In-Reply-To: <20251027133008.360237-1-elder@riscstar.com>

Define DTS nodes to enable support for QSPI on the K1 SoC, including the
pin control configuration used.  Enable QSPI on the Banana Pi BPI-F3 board.

Signed-off-by: Alex Elder <elder@riscstar.com>
---
 .../boot/dts/spacemit/k1-bananapi-f3.dts      |  6 ++++++
 arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi  | 21 +++++++++++++++++++
 arch/riscv/boot/dts/spacemit/k1.dtsi          | 16 ++++++++++++++
 3 files changed, 43 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index 33ca816bfd4b3..02f218a16318e 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -113,6 +113,12 @@ &pdma {
 	status = "okay";
 };
 
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_cfg>;
+	status = "okay";
+};
+
 &i2c2 {
 	pinctrl-0 = <&i2c2_0_cfg>;
 	pinctrl-names = "default";
diff --git a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
index 4eef81d583f3d..e922e05ff856d 100644
--- a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
@@ -73,6 +73,27 @@ i2c8-0-pins {
 		};
 	};
 
+	qspi_cfg: qspi-cfg {
+		qspi-pins {
+			pinmux = <K1_PADCONF(98, 0)>,    /* QSPI_DATA3 */
+				 <K1_PADCONF(99, 0)>,    /* QSPI_DATA2 */
+				 <K1_PADCONF(100, 0)>,   /* QSPI_DATA1 */
+				 <K1_PADCONF(101, 0)>,   /* QSPI_DATA0 */
+				 <K1_PADCONF(102, 0)>;   /* QSPI_CLK */
+
+			bias-disable;
+			drive-strength = <19>;
+			power-source = <3300>;
+		};
+
+		qspi-cs1-pins {
+			pinmux = <K1_PADCONF(103, 0)>;   /* QSPI_CS1 */
+			bias-pull-up = <0>;
+			drive-strength = <19>;
+			power-source = <3300>;
+		};
+	};
+
 	/omit-if-no-ref/
 	uart0_0_cfg: uart0-0-cfg {
 		uart0-0-pins {
diff --git a/arch/riscv/boot/dts/spacemit/k1.dtsi b/arch/riscv/boot/dts/spacemit/k1.dtsi
index af35f9cd64351..47f97105bff0b 100644
--- a/arch/riscv/boot/dts/spacemit/k1.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1.dtsi
@@ -823,6 +823,22 @@ uart9: serial@d4017800 {
 				status = "disabled";
 			};
 
+			qspi: spi@d420c000 {
+				compatible = "spacemit,k1-qspi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x0 0xd420c000 0x0 0x1000>,
+				      <0x0 0xb8000000 0x0 0xc00000>;
+				reg-names = "QuadSPI", "QuadSPI-memory";
+				clocks = <&syscon_apmu CLK_QSPI_BUS>,
+					 <&syscon_apmu CLK_QSPI>;
+				clock-names = "qspi_en", "qspi";
+				resets = <&syscon_apmu RESET_QSPI>,
+					 <&syscon_apmu RESET_QSPI_BUS>;
+				interrupts = <117>;
+				status = "disabled";
+			};
+
 			/* sec_uart1: 0xf0612000, not available from Linux */
 		};
 
-- 
2.48.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

  parent reply	other threads:[~2025-10-27 13:30 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-10-27 13:29 [PATCH v4 0/9] spi: enable the SpacemiT K1 SoC QSPI Alex Elder
2025-10-27 13:29 ` [PATCH v4 1/9] dt-bindings: spi: fsl-qspi: support SpacemiT K1 Alex Elder
2025-11-06 16:55   ` Mark Brown
2025-10-27 13:30 ` [PATCH v4 2/9] dt-bindings: spi: fsl-qspi: add optional resets Alex Elder
2025-10-27 13:30 ` [PATCH v4 3/9] spi: fsl-qspi: add optional reset support Alex Elder
2025-10-27 13:30 ` [PATCH v4 4/9] spi: fsl-qspi: switch predicates to bool Alex Elder
2025-10-27 13:30 ` [PATCH v4 5/9] spi: fsl-qspi: add a clock disable quirk Alex Elder
2025-10-27 13:30 ` [PATCH v4 6/9] spi: fsl-qspi: introduce sfa_size devtype data Alex Elder
2025-10-27 13:30 ` [PATCH v4 7/9] spi: fsl-qspi: support the SpacemiT K1 SoC Alex Elder
2025-10-27 13:30 ` Alex Elder [this message]
2025-10-27 13:30 ` [PATCH v4 9/9] riscv: defconfig: enable SPI_FSL_QUADSPI as a module Alex Elder
2025-11-12 11:19   ` Yixun Lan
2025-11-07 10:15 ` (subset) [PATCH v4 0/9] spi: enable the SpacemiT K1 SoC QSPI Mark Brown
2025-11-12 10:23 ` Yixun Lan
2025-11-12 18:56 ` Conor Dooley

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20251027133008.360237-9-elder@riscstar.com \
    --to=elder@riscstar.com \
    --cc=Frank.li@nxp.com \
    --cc=broonie@kernel.org \
    --cc=dlan@gentoo.org \
    --cc=guodong@riscstar.com \
    --cc=han.xu@nxp.com \
    --cc=imx@lists.linux.dev \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-riscv@lists.infradead.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=spacemit@lists.linux.dev \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox