[PATCH 0/4] riscv: dts: spacemit: improve Milk-V Jupiter device tree

[PATCH 0/4] riscv: dts: spacemit: improve Milk-V Jupiter device tree

[Aurelien Jarno]

This patchset updates the Milk-V Jupiter device tree to align with the
changes recently done for other SpacemiT K1 based boards.

In addition the last patch enables SD card support, but it depends on
the SD card support series for the K1 SoC to be merged first:
https://lore.kernel.org/linux-riscv/20260511-orangepi-sd-card-uhs-v9-0-ae48c0b2b2cf@gmail.com/

Aurelien Jarno (4):
  riscv: dts: spacemit: set console baud rate on Milk-V Jupiter
  riscv: dts: spacemit: sort aliases on Milk-V Jupiter
  riscv: dts: spacemit: enable eMMC on Milk-V Jupiter
  riscv: dts: spacemit: enable SD card support on Milk-V Jupiter

 .../boot/dts/spacemit/k1-milkv-jupiter.dts    | 35 +++++++++++++++++--
 1 file changed, 32 insertions(+), 3 deletions(-)

-- 
2.53.0


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH 1/4] riscv: dts: spacemit: set console baud rate on Milk-V Jupiter

[Aurelien Jarno]

Because the default console's baud rate is not set, defconfig kernels do
not have any serial output on this platform. Set the baud rate to
115200, matching what is used by U-Boot etc on this platform.

See-also: 24c12ca43b12c ("dts: spacemit: set console baud rate on bpif3")
Fixes: 5b90a3d6092d9 ("riscv: dts: spacemit: Add Milk-V Jupiter board device tree")
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
---
 arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
index 95c35154da96d..9b1dfddf2bac5 100644
--- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
@@ -21,7 +21,7 @@ aliases {
 	};
 
 	chosen {
-		stdout-path = "serial0";
+		stdout-path = "serial0:115200n8";
 	};
 
 	leds {
-- 
2.53.0


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH 2/4] riscv: dts: spacemit: sort aliases on Milk-V Jupiter

[Aurelien Jarno]

Before adding more aliases, just sort them.

Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
---
 arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
index 9b1dfddf2bac5..450d28e438293 100644
--- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
@@ -15,9 +15,9 @@ / {
 	aliases {
 		ethernet0 = &eth0;
 		ethernet1 = &eth1;
-		serial0 = &uart0;
 		i2c2 = &i2c2;
 		i2c8 = &i2c8;
+		serial0 = &uart0;
 	};
 
 	chosen {
-- 
2.53.0


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH 3/4] riscv: dts: spacemit: enable eMMC on Milk-V Jupiter

[Aurelien Jarno]

The Milk-V Jupiter board has a connector for an eMMC module. Add an
entry for it in the device tree and alias it mmc0. As it is not
populated by default, do no mark it as non-removable.

Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
---
 arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
index 450d28e438293..b9b8ddc8e7fb0 100644
--- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
@@ -17,6 +17,7 @@ aliases {
 		ethernet1 = &eth1;
 		i2c2 = &i2c2;
 		i2c8 = &i2c8;
+		mmc0 = &emmc;
 		serial0 = &uart0;
 	};
 
@@ -138,6 +139,15 @@ &cpu_7 {
 	cpu-supply = <&buck1_3v45>;
 };
 
+&emmc {
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
 &eth0 {
 	phy-handle = <&rgmii0>;
 	phy-mode = "rgmii-id";
-- 
2.53.0


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH 4/4] riscv: dts: spacemit: enable SD card support on Milk-V Jupiter

[Aurelien Jarno]

Add complete SD card controller support with UHS high-speed modes.

- Enable sdhci0 controller with 4-bit bus width
- Configure card detect GPIO with pull-up
- Connect vmmc-supply to buck4 for 3.3V card power
- Connect vqmmc-supply to aldo1 for 1.8V/3.3V I/O switching
- Add dual pinctrl states for voltage-dependent pin configuration
- Support UHS-I SDR25, SDR50, and SDR104 modes
- Alias it as mmc1

Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
---
 .../boot/dts/spacemit/k1-milkv-jupiter.dts    | 21 ++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)

diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
index b9b8ddc8e7fb0..7cf77437e0c2d 100644
--- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
@@ -18,6 +18,7 @@ aliases {
 		i2c2 = &i2c2;
 		i2c8 = &i2c8;
 		mmc0 = &emmc;
+		mmc1 = &sdhci0;
 		serial0 = &uart0;
 	};
 
@@ -282,7 +283,7 @@ buck6 {
 				regulator-always-on;
 			};
 
-			aldo1 {
+			aldo1: aldo1 {
 				regulator-min-microvolt = <500000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -417,6 +418,24 @@ uboot@a00000 {
 	};
 };
 
+&sdhci0 {
+	pinctrl-names = "default", "uhs";
+	pinctrl-0 = <&mmc1_cfg>;
+	pinctrl-1 = <&mmc1_uhs_cfg>;
+	bus-width = <4>;
+	cd-gpios = <&gpio K1_GPIO(80) (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	no-mmc;
+	no-sdio;
+	disable-wp;
+	cap-sd-highspeed;
+	vmmc-supply = <&buck4_3v3>;
+	vqmmc-supply = <&aldo1>;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_2_cfg>;
-- 
2.53.0


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv