[PATCH v6 00/18] drm: starfive: jh7110: Enable display subsystem

[PATCH v6 00/18] drm: starfive: jh7110: Enable display subsystem

[Michal Wilczynski]

This series enables the display subsystem on the StarFive JH7110.

Merging: the series splits by subsystem, there is no build dependency
between the blocks, and each block lands in the tree that already owns
those files:

  drm-misc                     1-3, 6, 8-13, 16
    drivers/gpu/drm/bridge/, include/drm/bridge/ and the display
    bindings. Patches 1 and 2 are inno-hdmi fixes with Fixes: tags;
    they apply to Rockchip as much as to StarFive and are independent
    of the rest, so they can go on their own.

  Conor's tree                 4, 5, 7, 14-15, 17
    bindings/soc/starfive/ (STARFIVE SOC DRIVERS),
    arch/riscv/boot/dts/starfive/ (STARFIVE DEVICETREES), and
    drivers/soc/starfive/, which this series creates.

  -                            18
    MAINTAINERS.

The PHY patches are now a separate series for linux-phy, as Vinod
suggested: "phy: Add the StarFive JH7110 Innosilicon HDMI PHY" [1]. This
series depends on it, and the DT needs the PHY driver at runtime. There
is no build dependency.

[1] https://lore.kernel.org/all/20261028-jh7110-inno-hdmi-phy-v6-0-f3379684d97e@samsung.com/

Ordering: patch 4 references the bindings from patch 3 and the PHY
series, the example in patch 7 instantiates nodes from patches 3 and 6
and the PHY series, and the DT in patch 17 uses all of them. Patches 4,
7 and 17 therefore need the drm-misc bindings and the PHY series in
place to pass dt_binding_check and dtbs_check. Patches 5, 14 and 15 have
no such dependency.

There are no out-of-tree dependencies: the dc8200 driver, the th1520
reset controller and the inno-hdmi bridge that the RFC listed as
prerequisites are all upstream now.

One more dependency: the clk patch that was 14/20 in v4 has been
applied by Brian Masney through the clk tree (af384d6e0573 in
linux-next). The DT patch needs it at runtime for the pixel MUXes to
follow the PHY.

The dom_vout block holds the display controller (dc8200), the clock
generator (voutcrg) and the HDMI IP, all inside PD_VOUT. The HDMI IP is
a single register block containing both the controller and the PHY,
which are described as separate children because they have separate
resources:

  - the PHY takes only the 24 MHz reference clock, and provides the
    pixel clock that voutcrg routes on to the dc8200 pixel MUXes, and
    the phy the controller uses
  - the controller takes pclk/mclk/bclk from voutcrg

It is the same Innosilicon PHY that the RK3328 describes as its own
hdmiphy node; here it shares a register window with the controller.

The parent maps the register block and owns the regmap its two children
share. Everything in the region sits behind one NoC port whose clock and
reset gate access to it, inside PD_VOUT, so the vout subsystem node from
the RFC is back and owns those for as long as any child exists.

Patch 11 adds a .mode_valid platform op to inno-hdmi.
inno_hdmi_bridge_mode_valid() checks the pixel clock against
hdmi->refclk, but that clock only exists where a "ref" clock is
described. The JH7110 gets its pixel clock from the PHY, so refclk is
NULL and the check was skipped: unsupported modes were advertised, the
modeset then "succeeded" because the atomic enable path cannot fail, and
the display stayed blank.

Patch 12 makes the inno-hdmi PHY configuration table optional. The
JH7110 drives its PHY through a separate driver, so the table only ever
existed to get past a probe time check, and the register writes it fed
belong to the integrated PHY the JH7110 does not have.

Patches 1, 2 and 8-13 change the inno-hdmi bridge, which the Rockchip
RK3036 and RK3128 use as well. I have no Rockchip hardware, so on
Rockchip they are build tested only (arm and riscv). A Tested-by would
help.

Testing
=======

Tested on a VisionFive 2 v1.3B using modetest, with the PHY series
applied.

All 42 modes the sink advertises work, with nothing in dmesg. Pixel
clocks run from 25.175 MHz (640x480@59.94) up to 297 MHz
(4096x2160@30), including 3840x2160 and the full 1920x1080 and 1280x720
rate families.

The four modes the RFC reported as broken work now too: 2560x1440@59.95,
2048x1080@60.00, 2048x1080@24.00 and 720x400@70.08.

Before patch 11, four of the advertised modes failed: 1680x1050@59.95
(146.250 MHz), 1400x1050@59.98 (121.750), 1152x864@59.97 (81.768) and
1280x768@60.35 (80.140). Those pixel clocks are not in the PHY pre-PLL
table, so clk_set_rate() returned -EINVAL and the screen stayed black
while userspace saw a successful modeset. They are rejected in
.mode_valid now; the other refresh rates of those resolutions still work.

The mux the HDMI controller programs in dom_vout_syscon has a DP and a
DPI branch, and the DT wires the DPI one, so the DP branch was checked
separately by moving the input endpoint to the DC8200's DP output on a
throwaway branch. SYSCFG_4 reads 0x4c0b0000 instead of 0x0c0b0000, the
output is identical to the DPI path and all 42 modes set. Sweeping
VOUT_HDMI_DP_YUV_MODE over its four values with a mode held shows only
RGB giving a correct picture, as documented.

Every commit builds for riscv, and the Rockchip inno-hdmi glue also for
arm.

Notes
=====

The JH7110 has no central MAINTAINERS entry and maintainership is
fragmented, so patch 18 adds one for the display subsystem and I am
happy to help maintain it. The PHY series adds its own entry for the
JH7110 HDMI PHY.

checkpatch warns "does MAINTAINERS need updating?" on the patches adding
files, because that entry comes in patch 18.

Thanks to Icenowy Zheng for the dc8200 driver and for explaining how the
SoC and the display pipeline fit together.

Thanks also to Dominique Belhachemi, who got rid of the vout-subsystem
wrapper and helped with the testing, to Maud Spierings for testing on a
Framework 13 panel, to Byron Stanoszek and OOHehir for testing v5, and
to Graham Markall for testing the JH7110 display patches independently
and writing up the results:
https://big-grey.co.uk/2026/01/26/testing-starfive-jh7110-display-controller-patches/

Link to v1: https://lore.kernel.org/all/20251108-jh7110-clean-send-v1-0-06bf43bb76b1@samsung.com/

---
Changes in v6:
- Split the PHY patches into their own series (Vinod)
- New patch 2: the hotplug NULL drm_device guard is split out of "Split
  probe out of bind" into its own patch (Heiko)
- inno_hdmi_bind() takes a platform_device, like dw_hdmi_bind() (Heiko)
- Describe the HDMI PHY node by its resources rather than by the probe
  cycle, in the commit messages and the Kconfig help (Krzysztof)
- Rebased onto v7.3, collected tags
- Link to v5: https://lore.kernel.org/r/20260929-jh7110-clean-send-v5-0-82b4d8e3c6c7@samsung.com

Changes in v5:
- Rebased onto v7.3-rc5.
- Dropped the clk patch, applied as af384d6e0573.
- New patch 13 makes the HDMI_SYS_CTRL register clock source selectable
  per platform, and the JH7110 selects the TMDS clock. The driver drove
  the register interface from the system clock for everyone, and a
  Framework 13 panel flickers continuously that way (Maud Spierings).
  Rockchip keeps the system clock, so this is a no-op there. This was
  listed as a known limitation in v4.
- New patch 1 fixes v_HSYNC_POLARITY and v_VSYNC_POLARITY, which have
  been swapped in inno-hdmi since the driver was merged. The hardware
  puts HSYNC in bit 2 and VSYNC in bit 3, and the driver had them the
  other way round. Almost all CEA modes drive both syncs with the same
  polarity, so the two writes are indistinguishable and the bug only
  shows on a mode whose polarities differ - a band of black rows at the
  top of the screen, vsync_end - vsync_start + 1 rows tall. Reported
  independently by Dominique Belhachemi, Maud Spierings and Byron
  Stanoszek, and confirmed against the RK3128 TRM by Icenowy Zheng, so
  this is a Rockchip fix too.
- Added a 201 MHz entry to the JH7110 pre-PLL table for a 2560x1440
  mode Byron Stanoszek runs on a Dell U2711. It is derived the same way
  as the neighbouring entries (fbdiv 134, /16, VCO 3.216 GHz) but I have
  no sink that asks for it, so it is untested on my hardware.
- Moved the hdmi-subsystem binding from bindings/mfd/ to
  bindings/soc/starfive/, next to the vout-subsystem binding and matching
  its driver in drivers/soc/starfive/. The mfd/ path was left over from
  when the driver was called hdmi-mfd; nothing in the series is an MFD
  device, and it meant one isolated binding patch would have had to go
  through the MFD tree on its own.
- The commit message for "Split probe out of bind" claimed a matching
  inno_hdmi_remove(); no such function exists, so the claim is gone.
- Dropped Joshua Peisach's Reviewed-by from the PHY driver patch as well,
  since that patch changed in v5.
- Dropped Joshua Peisach's Reviewed-by from the binding patches; he said
  he is not reviewing DT (Krzysztof Kozlowski). It is kept on the driver
  patches he did look at.
- Removed a probe-time clk_set_rate() from the PHY driver. It programmed
  a default rate, and .set_rate writes PHY registers that live in the
  window gated by the controller's system clock - a clock the PHY cannot
  hold without creating a probe cycle with voutcrg.
- Link to v4: https://lore.kernel.org/r/20260915-jh7110-clean-send-v4-0-f0e4fd6f2cc8@samsung.com

Changes in v4:
- New patch 11 makes the inno-hdmi PHY configuration table optional, so
  the JH7110 controller can drop the dummy two entry table it carried
  only to satisfy the probe time check, along with the integrated PHY
  register writes that table fed (Icenowy Zheng). That table was also
  acting as an upper bound: inno_hdmi_find_phy_config() runs before the
  platform .mode_valid and returns early, so its 297 MHz sentinel
  rejected every mode above that even though the PHY pre-PLL table has a
  594 MHz entry. Nothing here advertises such a mode, so it was latent.
- Fixed a v3 regression: CLK_SET_RATE_NO_REPARENT stops clk_set_rate()
  from reparenting the dc8200 pixel MUXes, so they kept whatever the
  bootloader had selected and the display stayed black on boards where
  that was not the HDMI PHY. They get assigned-clock-parents now (Maud
  Spierings, Dominique Belhachemi).
- vout-subsystem binding: describe the children by compatible instead of
  $ref, as qcom,sm8750-mdss does, and show the whole subsystem with all
  four children in the example (Krzysztof Kozlowski).
- Dropped the vout-syscon example from starfive,jh7110-syscon.yaml, it
  is part of the vout subsystem example now (Krzysztof Kozlowski).
- Renamed the xin24m node to xin24m-clock (Krzysztof Kozlowski).
- Fixed the HDMI HPD pinmux: it drove the pin high (GPOUT_HIGH with the
  output enabled) while also reading it as the hotplug input, so HPD
  could only ever read asserted. It is an input now.
- jh7110-inno-hdmi: dropped a regmap lookup whose result was never used;
  inno_hdmi_probe() fetches the parent regmap itself. The commit message
  claimed otherwise and is corrected.
- phy: rockchip: dropped two now unused RK3328 spread spectrum macros
  the v3 cleanup missed. The register write itself moved to the shared
  helper and is unchanged, so Chaoyi's Reviewed-by is carried over.
- inno-hdmi: the hotplug handler dereferenced bridge.dev unconditionally.
  Splitting probe out of bind moved the interrupt request to probe, so
  an HPD event before the DRM master attaches the bridge would oops.
  Guarded.
- Dropped the <linux/mod_devicetable.h> includes (Uwe Kleine-König).
- jh7110-inno-hdmi: __free(device_node) for the graph lookups, and
  dropped the redundant negative check on clk_round_rate() (Chaoyi Chen).
- phy: rockchip: dropped the recalc_rate debug print that the shared
  helper already emits (Chaoyi Chen).
- Rebased onto v7.3-rc3.
- Link to v3: https://lore.kernel.org/r/20260904-jh7110-clean-send-v3-0-484f9ae72715@samsung.com

Changes in v3:
- Brought back the vout subsystem node and driver, now owning the NoC
  bus clock, its reset and PD_VOUT for the whole region, with dc8200,
  the HDMI block, the syscon and voutcrg as its children (Icenowy Zheng).
- Fixed a hard hang when the bridge is built as a module: the PHY's
  .is_prepared read a register in the window gated by the controller's
  system clock, so clk_disable_unused() wedged the CPU before the
  controller had bound. The op is gone; the framework uses the software
  prepare count instead. (Marek Szyprowski)
- The HDMI controller now programs the display mux in dom_vout_syscon
  from the port graph rather than inheriting whatever the bootloader
  left, with a phandle to the syscon (Icenowy Zheng).
- The register access clock is named "pclk" to match the existing
  inno-hdmi binding, so the generic driver no longer picks up the pixel
  clock. Previously it held the pre-PLL powered from probe and sized the
  DDC divider from the wrong rate.
- Dropped the clk suffixes and the single-entry -names properties from
  the bindings (Conor Dooley). mclk and bclk keep their names: per TRM
  5.3 they are the HDMI audio clocks, not module and bus clocks, so the
  descriptions say that instead.
- Replaced patternProperties with plain properties in the hdmi-subsystem
  binding (Conor Dooley).
- dc8200 gets an SoC specific compatible, and inherits dma-noncoherent
  from the subsystem bus node, so it validates against verisilicon,dc.
- Added the pre-PLL entry for the Framework 13 panel and fixed two
  devicetree whitespace nits (Maud Spierings).
- select REGMAP_MMIO, CLK_SET_RATE_NO_REPARENT on the dc8200 pixel MUXes
  so clk_set_rate() cannot reroute them, and inno-hdmi register reads
  return 0 instead of stack garbage when regmap_read() fails.
- phy: rockchip: dropped the local pre-PLL lookup wrapper and the 28 now
  unused RK3328 pre-PLL macros, and restored the VCO debug output, this
  time in the shared helper so both drivers get it (Jonas Karlman).
- Rebased onto v7.3-rc1.
- Link to v2: https://lore.kernel.org/r/20260828-jh7110-clean-send-v2-0-331680c8b9d1@samsung.com

Changes since the RFC:
- Dropped the vout-subsystem wrapper driver and its binding, along with
  the patch relaxing the voutcrg binding; genpd handles PD_VOUT per
  node.
- Renamed the compatible to starfive,jh7110-hdmi-subsystem, dropping
  "mfd" as a Linux term (Conor Dooley).
- Absolute $refs in the bindings, unused example labels dropped, and the
  examples deduplicated between parent and children (Conor Dooley).
- Added the .mode_valid platform operation (patch 7).
- Split the inno-hdmi rework into a mechanical probe/bind split (patch
  4)
  and the regmap-from-parent change (patch 5). struct inno_hdmi is no
  longer exported; no platform glue dereferences it.
- Replaced the duplicated PHY driver with a shared Innosilicon library
  and moved Rockchip onto it (patches 11-13).
- Fixed pre-PLL lock detection, which masked the status read with the
  register address instead of the lock bit.
- Fixed a pixel clock refcount underflow: enable returns early on
  failure while disable tore down unconditionally.
- voutcrg patch reduced to adding CLK_SET_RATE_PARENT to the two dc8200
  pixel MUXes.
- Rebased onto v7.2.

---
Michal Wilczynski (18):
      drm/bridge: inno-hdmi: fix swapped HSYNC and VSYNC polarity
      drm/bridge: inno-hdmi: Don't dereference a NULL drm_device on hotplug
      dt-bindings: display: bridge: Add starfive,jh7110-inno-hdmi-controller
      dt-bindings: soc: starfive: Add starfive,jh7110-hdmi-subsystem
      dt-bindings: soc: starfive: Add starfive,jh7110-vout-syscon
      dt-bindings: display: verisilicon: Add starfive,jh7110-dc8200
      dt-bindings: soc: starfive: Add starfive,jh7110-vout-subsystem
      drm/bridge: inno-hdmi: Split probe out of bind
      drm/bridge: inno-hdmi: Allow the register map to come from a parent
      drm/bridge: inno-hdmi: Add .disable platform operation
      drm/bridge: inno-hdmi: Add .mode_valid platform operation
      drm/bridge: inno-hdmi: Make the PHY configuration table optional
      drm/bridge: inno-hdmi: Make the register clock source selectable
      soc: starfive: Add jh7110-hdmi-subsystem driver
      soc: starfive: Add jh7110-vout-subsystem driver
      drm/bridge: starfive: Add JH7110 HDMI controller driver
      riscv: dts: starfive: jh7110: Update DT for display subsystem
      MAINTAINERS: Add StarFive JH7110 display subsystem entry

 .../starfive,jh7110-inno-hdmi-controller.yaml      | 121 +++++++++
 .../bindings/display/verisilicon,dc.yaml           |   1 +
 .../starfive/starfive,jh7110-hdmi-subsystem.yaml   |  95 +++++++
 .../soc/starfive/starfive,jh7110-syscon.yaml       |   1 +
 .../starfive/starfive,jh7110-vout-subsystem.yaml   | 218 +++++++++++++++
 MAINTAINERS                                        |  11 +
 arch/riscv/boot/dts/starfive/jh7110-common.dtsi    | 121 ++++++++-
 arch/riscv/boot/dts/starfive/jh7110.dtsi           | 105 ++++++--
 drivers/gpu/drm/bridge/Kconfig                     |  11 +
 drivers/gpu/drm/bridge/Makefile                    |   1 +
 drivers/gpu/drm/bridge/inno-hdmi.c                 | 118 ++++++--
 drivers/gpu/drm/bridge/jh7110-inno-hdmi.c          | 296 +++++++++++++++++++++
 drivers/gpu/drm/rockchip/inno_hdmi-rockchip.c      |   2 +-
 drivers/soc/Kconfig                                |   1 +
 drivers/soc/Makefile                               |   1 +
 drivers/soc/starfive/Kconfig                       |  42 +++
 drivers/soc/starfive/Makefile                      |   3 +
 drivers/soc/starfive/jh7110-hdmi-subsystem.c       |  72 +++++
 drivers/soc/starfive/jh7110-vout-subsystem.c       |  82 ++++++
 include/drm/bridge/inno_hdmi.h                     |  14 +-
 20 files changed, 1269 insertions(+), 47 deletions(-)
---
base-commit: c03c1a14507dfaf8b856c2608f9ac216021fc222
change-id: 20251031-jh7110-clean-send-7d2242118026
prerequisite-change-id: 20261028-jh7110-inno-hdmi-phy-83e5cfa643e3:v6
prerequisite-patch-id: d0734cca85ae4192ed921fb1a0b9e4bdb4e9ae6a
prerequisite-patch-id: 7ffec3af58389aa090d5a9947889060dd5493138
prerequisite-patch-id: 4a3488cc151ae0e9ef053ea67e8e520520c7df15
prerequisite-patch-id: 37de8eb6867db62f75e39908a136684a1cc14743
prerequisite-patch-id: 27aeff98d5c0b0bdb3eb9e9bbc2bf5e982864774
prerequisite-patch-id: f0e814166bef9f12a11c54de07203b17bd97a027

Best regards,
-- 
Michal Wilczynski <m.wilczynski@samsung.com>


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 01/18] drm/bridge: inno-hdmi: fix swapped HSYNC and VSYNC polarity

[Michal Wilczynski]

v_HSYNC_POLARITY() and v_VSYNC_POLARITY() write the wrong bits: the
hardware puts HSYNC in bit 2 and VSYNC in bit 3, the macros do the
opposite. Most CEA modes drive both syncs with the same polarity so it
goes unnoticed; it only shows up on modes where the two differ.

Fixes: 412d4ae6b7a5 ("drm/rockchip: hdmi: add Innosilicon HDMI support")
Reported-by: Maud Spierings <maud_spierings@murena.io>
Closes: https://lore.kernel.org/all/e780ecb8-918f-4816-99c8-b69b10b25a18@murena.io/
Reported-by: Byron Stanoszek <gandalf@winds.org>
Closes: https://lore.kernel.org/all/b8b046ee-c574-3e16-6079-2fc415633dae@winds.org/
Suggested-by: Dominique Belhachemi <db@domibel.de>
Tested-by: Maud Spierings <maud_spierings@murena.io>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/gpu/drm/bridge/inno-hdmi.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
index dd35f5a875d3d842fee6d2ead0de88503f9914e1..d7c33b92e2ddf4ced84d17304463f44be52270b8 100644
--- a/drivers/gpu/drm/bridge/inno-hdmi.c
+++ b/drivers/gpu/drm/bridge/inno-hdmi.c
@@ -122,8 +122,8 @@ enum {
 #define v_VIDEO_MUTE(n)			((n) << 0)
 
 #define HDMI_VIDEO_TIMING_CTL		0x08
-#define v_HSYNC_POLARITY(n)		((n) << 3)
-#define v_VSYNC_POLARITY(n)		((n) << 2)
+#define v_VSYNC_POLARITY(n)		((n) << 3)
+#define v_HSYNC_POLARITY(n)		((n) << 2)
 #define v_INETLACE(n)			((n) << 1)
 #define v_EXTERANL_VIDEO(n)		((n) << 0)
 

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v6 01/18] drm/bridge: inno-hdmi: fix swapped HSYNC and VSYNC polarity

[Heiko Stuebner]

Am Donnerstag, 29. Oktober 2026, 08:53:35 Mitteleuropäische Normalzeit schrieb Michal Wilczynski:
> v_HSYNC_POLARITY() and v_VSYNC_POLARITY() write the wrong bits: the
> hardware puts HSYNC in bit 2 and VSYNC in bit 3, the macros do the
> opposite. Most CEA modes drive both syncs with the same polarity so it
> goes unnoticed; it only shows up on modes where the two differ.
> 
> Fixes: 412d4ae6b7a5 ("drm/rockchip: hdmi: add Innosilicon HDMI support")
> Reported-by: Maud Spierings <maud_spierings@murena.io>
> Closes: https://lore.kernel.org/all/e780ecb8-918f-4816-99c8-b69b10b25a18@murena.io/
> Reported-by: Byron Stanoszek <gandalf@winds.org>
> Closes: https://lore.kernel.org/all/b8b046ee-c574-3e16-6079-2fc415633dae@winds.org/
> Suggested-by: Dominique Belhachemi <db@domibel.de>
> Tested-by: Maud Spierings <maud_spierings@murena.io>
> Tested-by: Byron Stanoszek <gandalf@winds.org>
> Tested-by: OOHehir <oo.hehir@gmail.com>
> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>


RK3036 TRM agrees with this assesment :-)

Reviewed-by: Heiko Stuebner <heiko@sntech.de>



_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 02/18] drm/bridge: inno-hdmi: Don't dereference a NULL drm_device on hotplug

[Michal Wilczynski]

inno_hdmi_irq() passes hdmi->bridge.dev to drm_helper_hpd_irq_event(),
which dereferences it in its first statement:

	if (!dev->mode_config.poll_enabled)

bridge.dev is assigned only by drm_bridge_attach(), but inno_hdmi_bind()
unmutes the hotplug interrupt in inno_hdmi_init_hw() and installs the
handler well before it attaches the bridge:

	inno_hdmi_init_hw(hdmi);		/* unmutes hotplug */
	devm_request_threaded_irq(...);		/* handler goes live */
	...
	hdmi->bridge.ddc = inno_hdmi_i2c_adapter(hdmi);
	devm_drm_bridge_add(dev, &hdmi->bridge);
	drm_bridge_attach(...);			/* bridge.dev set here */

The bridge is allocated by devm_drm_bridge_alloc(), which kzalloc()s it,
so bridge.dev is NULL for all of that window, and a hotplug event
arriving in it enters drm_helper_hpd_irq_event(NULL).

Before the conversion to a bridge the ordering was safe:
inno_hdmi_register() called drmm_connector_hdmi_init(), which set
connector.dev, before the interrupt was requested.

Drop hotplug events that arrive before the bridge is attached.

Fixes: 969325a2597e ("drm/rockchip: inno-hdmi: Convert to drm bridge")
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/gpu/drm/bridge/inno-hdmi.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
index d7c33b92e2ddf4ced84d17304463f44be52270b8..d29832249b942dec84fb9d07a0b21ee751fc0486 100644
--- a/drivers/gpu/drm/bridge/inno-hdmi.c
+++ b/drivers/gpu/drm/bridge/inno-hdmi.c
@@ -929,7 +929,13 @@ static irqreturn_t inno_hdmi_irq(int irq, void *dev_id)
 {
 	struct inno_hdmi *hdmi = dev_id;
 
-	drm_helper_hpd_irq_event(hdmi->bridge.dev);
+	/*
+	 * The interrupt is requested before the bridge is attached, and
+	 * bridge.dev is only set by drm_bridge_attach(). Drop hotplug events
+	 * that arrive before then rather than dereference a NULL drm_device.
+	 */
+	if (hdmi->bridge.dev)
+		drm_helper_hpd_irq_event(hdmi->bridge.dev);
 
 	return IRQ_HANDLED;
 }

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v6 02/18] drm/bridge: inno-hdmi: Don't dereference a NULL drm_device on hotplug

[Heiko Stuebner]

Am Donnerstag, 29. Oktober 2026, 08:53:36 Mitteleuropäische Normalzeit schrieb Michal Wilczynski:
> inno_hdmi_irq() passes hdmi->bridge.dev to drm_helper_hpd_irq_event(),
> which dereferences it in its first statement:
> 
> 	if (!dev->mode_config.poll_enabled)
> 
> bridge.dev is assigned only by drm_bridge_attach(), but inno_hdmi_bind()
> unmutes the hotplug interrupt in inno_hdmi_init_hw() and installs the
> handler well before it attaches the bridge:
> 
> 	inno_hdmi_init_hw(hdmi);		/* unmutes hotplug */
> 	devm_request_threaded_irq(...);		/* handler goes live */
> 	...
> 	hdmi->bridge.ddc = inno_hdmi_i2c_adapter(hdmi);
> 	devm_drm_bridge_add(dev, &hdmi->bridge);
> 	drm_bridge_attach(...);			/* bridge.dev set here */
> 
> The bridge is allocated by devm_drm_bridge_alloc(), which kzalloc()s it,
> so bridge.dev is NULL for all of that window, and a hotplug event
> arriving in it enters drm_helper_hpd_irq_event(NULL).
> 
> Before the conversion to a bridge the ordering was safe:
> inno_hdmi_register() called drmm_connector_hdmi_init(), which set
> connector.dev, before the interrupt was requested.
> 
> Drop hotplug events that arrive before the bridge is attached.
> 
> Fixes: 969325a2597e ("drm/rockchip: inno-hdmi: Convert to drm bridge")
> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
> ---
>  drivers/gpu/drm/bridge/inno-hdmi.c | 8 +++++++-
>  1 file changed, 7 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
> index d7c33b92e2ddf4ced84d17304463f44be52270b8..d29832249b942dec84fb9d07a0b21ee751fc0486 100644
> --- a/drivers/gpu/drm/bridge/inno-hdmi.c
> +++ b/drivers/gpu/drm/bridge/inno-hdmi.c
> @@ -929,7 +929,13 @@ static irqreturn_t inno_hdmi_irq(int irq, void *dev_id)
>  {
>  	struct inno_hdmi *hdmi = dev_id;
>  
> -	drm_helper_hpd_irq_event(hdmi->bridge.dev);
> +	/*
> +	 * The interrupt is requested before the bridge is attached, and
> +	 * bridge.dev is only set by drm_bridge_attach(). Drop hotplug events
> +	 * that arrive before then rather than dereference a NULL drm_device.
> +	 */
> +	if (hdmi->bridge.dev)
> +		drm_helper_hpd_irq_event(hdmi->bridge.dev);

Reviewed-by: Heiko Stuebner <heiko@sntech.de>

Most other callers of drm_helper_hpd_irq_event() also do exactly this.


Heiko



_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v6 02/18] drm/bridge: inno-hdmi: Don't dereference a NULL drm_device on hotplug

[Heiko Stuebner]

Am Freitag, 30. Oktober 2026, 18:43:47 Mitteleuropäische Normalzeit schrieb Heiko Stuebner:
> Am Donnerstag, 29. Oktober 2026, 08:53:36 Mitteleuropäische Normalzeit schrieb Michal Wilczynski:
> > inno_hdmi_irq() passes hdmi->bridge.dev to drm_helper_hpd_irq_event(),
> > which dereferences it in its first statement:
> > 
> > 	if (!dev->mode_config.poll_enabled)
> > 
> > bridge.dev is assigned only by drm_bridge_attach(), but inno_hdmi_bind()
> > unmutes the hotplug interrupt in inno_hdmi_init_hw() and installs the
> > handler well before it attaches the bridge:
> > 
> > 	inno_hdmi_init_hw(hdmi);		/* unmutes hotplug */
> > 	devm_request_threaded_irq(...);		/* handler goes live */
> > 	...
> > 	hdmi->bridge.ddc = inno_hdmi_i2c_adapter(hdmi);
> > 	devm_drm_bridge_add(dev, &hdmi->bridge);
> > 	drm_bridge_attach(...);			/* bridge.dev set here */
> > 
> > The bridge is allocated by devm_drm_bridge_alloc(), which kzalloc()s it,
> > so bridge.dev is NULL for all of that window, and a hotplug event
> > arriving in it enters drm_helper_hpd_irq_event(NULL).
> > 
> > Before the conversion to a bridge the ordering was safe:
> > inno_hdmi_register() called drmm_connector_hdmi_init(), which set
> > connector.dev, before the interrupt was requested.
> > 
> > Drop hotplug events that arrive before the bridge is attached.
> > 
> > Fixes: 969325a2597e ("drm/rockchip: inno-hdmi: Convert to drm bridge")
> > Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
> > ---
> >  drivers/gpu/drm/bridge/inno-hdmi.c | 8 +++++++-
> >  1 file changed, 7 insertions(+), 1 deletion(-)
> > 
> > diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
> > index d7c33b92e2ddf4ced84d17304463f44be52270b8..d29832249b942dec84fb9d07a0b21ee751fc0486 100644
> > --- a/drivers/gpu/drm/bridge/inno-hdmi.c
> > +++ b/drivers/gpu/drm/bridge/inno-hdmi.c
> > @@ -929,7 +929,13 @@ static irqreturn_t inno_hdmi_irq(int irq, void *dev_id)
> >  {
> >  	struct inno_hdmi *hdmi = dev_id;
> >  
> > -	drm_helper_hpd_irq_event(hdmi->bridge.dev);
> > +	/*
> > +	 * The interrupt is requested before the bridge is attached, and
> > +	 * bridge.dev is only set by drm_bridge_attach(). Drop hotplug events
> > +	 * that arrive before then rather than dereference a NULL drm_device.
> > +	 */

nit: I don't think that huge comment is necessary for that


> > +	if (hdmi->bridge.dev)
> > +		drm_helper_hpd_irq_event(hdmi->bridge.dev);
> 
> Reviewed-by: Heiko Stuebner <heiko@sntech.de>
> 
> Most other callers of drm_helper_hpd_irq_event() also do exactly this.
> 
> 
> Heiko
> 





_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 03/18] dt-bindings: display: bridge: Add starfive,jh7110-inno-hdmi-controller

[Michal Wilczynski]

Add the dt-binding for the StarFive JH7110 Innosilicon HDMI controller
(DRM bridge).

This device is the second child of the starfive,jh7110-hdmi-subsystem node.
It consumes its register access, audio master and audio bit clocks
(pclk, mclk, bclk) from voutcrg, and both the pixel clock (pixel) and
the PHY from its hdmi_phy sibling.

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 .../starfive,jh7110-inno-hdmi-controller.yaml      | 121 +++++++++++++++++++++
 1 file changed, 121 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/bridge/starfive,jh7110-inno-hdmi-controller.yaml b/Documentation/devicetree/bindings/display/bridge/starfive,jh7110-inno-hdmi-controller.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..68e4e817d8fab55fac9af230239aa2b8aaf3e463
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/starfive,jh7110-inno-hdmi-controller.yaml
@@ -0,0 +1,121 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/starfive,jh7110-inno-hdmi-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 Innosilicon HDMI Controller
+
+maintainers:
+  - Michal Wilczynski <m.wilczynski@samsung.com>
+
+description:
+  The controller portion of the StarFive JH7110 INNO HDMI IP.
+
+properties:
+  compatible:
+    const: starfive,jh7110-inno-hdmi-controller
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: The HDMI controller main clock
+      - description: Audio master clock
+      - description: Audio bit clock, from the I2S transmitter
+      - description: The pixel clock, generated by the PHY
+
+  clock-names:
+    items:
+      - const: pclk
+      - const: mclk
+      - const: bclk
+      - const: pixel
+
+  resets:
+    maxItems: 1
+
+  phys:
+    maxItems: 1
+
+  starfive,vout-syscon:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to the dom_vout_syscon system controller, which holds the mux
+      selecting the DC8200 output that drives the HDMI transmitter.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Input from the DC8200. The remote port number selects the DC8200
+          panel and the remote endpoint number the interface on that panel,
+          0 for DPI and 1 for DP.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Output to the HDMI connector.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - interrupts
+  - clocks
+  - clock-names
+  - resets
+  - phys
+  - starfive,vout-syscon
+  - ports
+
+additionalProperties: false
+
+examples:
+  # Shown as a child of the HDMI subsystem node; see
+  # Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml
+  # for the full node.
+  - |
+    #include <dt-bindings/clock/starfive,jh7110-crg.h>
+    #include <dt-bindings/reset/starfive,jh7110-crg.h>
+
+    controller {
+        compatible = "starfive,jh7110-inno-hdmi-controller";
+        clocks = <&voutcrg JH7110_VOUTCLK_HDMI_TX_SYS>,
+                 <&voutcrg JH7110_VOUTCLK_HDMI_TX_MCLK>,
+                 <&voutcrg JH7110_VOUTCLK_HDMI_TX_BCLK>,
+                 <&hdmi_phy>;
+        clock-names = "pclk", "mclk", "bclk", "pixel";
+        interrupts = <99>;
+        phys = <&hdmi_phy>;
+        resets = <&voutcrg JH7110_VOUTRST_HDMI_TX_HDMI>;
+        starfive,vout-syscon = <&vout_syscon>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+
+                endpoint {
+                    remote-endpoint = <&dpu_out_dpi0>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+
+                endpoint {
+                    remote-endpoint = <&hdmi_con_in>;
+                };
+            };
+        };
+    };
+
+...

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 04/18] dt-bindings: soc: starfive: Add starfive,jh7110-hdmi-subsystem

[Michal Wilczynski]

Add the dt-binding for the StarFive JH7110 HDMI subsystem.

The JH7110 HDMI IP is a monolithic block containing both the digital
controller and analog PHY in a single register space. This binding
defines the parent device, which holds the shared register map, and its
two children: the PHY and the controller.

The two have separate resources. The PHY takes the 24 MHz reference
clock and provides both the pixel clock, which the VOUT clock generator
routes on to the display controller, and the phy the controller uses.
The controller takes its clocks from the VOUT clock generator. What
they share is the register space, which the parent maps.

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 .../starfive/starfive,jh7110-hdmi-subsystem.yaml   | 95 ++++++++++++++++++++++
 1 file changed, 95 insertions(+)

diff --git a/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml b/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..2ff8b0b920aec41a83f0aeaa0ed9c4249fe87f46
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml
@@ -0,0 +1,95 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 HDMI subsystem
+
+maintainers:
+  - Michal Wilczynski <m.wilczynski@samsung.com>
+
+description:
+  The StarFive JH7110 HDMI block is a monolithic IP containing both
+  the digital controller logic and the analog PHY logic in a single
+  register space. It sits inside the video output subsystem, which owns
+  the NoC bus clock and reset gating this region and the power domain it
+  belongs to.
+
+properties:
+  compatible:
+    const: starfive,jh7110-hdmi-subsystem
+
+  reg:
+    maxItems: 1
+
+  phy:
+    $ref: /schemas/phy/starfive,jh7110-inno-hdmi-phy.yaml#
+
+  controller:
+    $ref: /schemas/display/bridge/starfive,jh7110-inno-hdmi-controller.yaml#
+
+required:
+  - compatible
+  - reg
+  - phy
+  - controller
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/starfive,jh7110-crg.h>
+    #include <dt-bindings/reset/starfive,jh7110-crg.h>
+
+    soc {
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        hdmi@29590000 {
+            compatible = "starfive,jh7110-hdmi-subsystem";
+            reg = <0x29590000 0x4000>;
+
+            controller {
+                compatible = "starfive,jh7110-inno-hdmi-controller";
+                clocks = <&voutcrg JH7110_VOUTCLK_HDMI_TX_SYS>,
+                         <&voutcrg JH7110_VOUTCLK_HDMI_TX_MCLK>,
+                         <&voutcrg JH7110_VOUTCLK_HDMI_TX_BCLK>,
+                         <&hdmi_phy>;
+                clock-names = "pclk", "mclk", "bclk", "pixel";
+                interrupts = <99>;
+                phys = <&hdmi_phy>;
+                resets = <&voutcrg JH7110_VOUTRST_HDMI_TX_HDMI>;
+                starfive,vout-syscon = <&vout_syscon>;
+
+                ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                        reg = <0>;
+
+                        endpoint {
+                            remote-endpoint = <&dpu_out_dpi0>;
+                        };
+                    };
+
+                    port@1 {
+                        reg = <1>;
+
+                        endpoint {
+                            remote-endpoint = <&hdmi_con_in>;
+                        };
+                    };
+                };
+            };
+
+            hdmi_phy: phy {
+                compatible = "starfive,jh7110-inno-hdmi-phy";
+                #clock-cells = <0>;
+                clocks = <&xin24m>;
+                #phy-cells = <0>;
+            };
+        };
+    };
+...

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v6 04/18] dt-bindings: soc: starfive: Add starfive,jh7110-hdmi-subsystem

[Rob Herring (Arm)]

On Thu, 29 Oct 2026 08:53:38 +0100, Michal Wilczynski wrote:
> Add the dt-binding for the StarFive JH7110 HDMI subsystem.
> 
> The JH7110 HDMI IP is a monolithic block containing both the digital
> controller and analog PHY in a single register space. This binding
> defines the parent device, which holds the shared register map, and its
> two children: the PHY and the controller.
> 
> The two have separate resources. The PHY takes the 24 MHz reference
> clock and provides both the pixel clock, which the VOUT clock generator
> routes on to the display controller, and the phy the controller uses.
> The controller takes its clocks from the VOUT clock generator. What
> they share is the register space, which the parent maps.
> 
> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
> ---
>  .../starfive/starfive,jh7110-hdmi-subsystem.yaml   | 95 ++++++++++++++++++++++
>  1 file changed, 95 insertions(+)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml: Unresolvable reference: /schemas/phy/starfive,jh7110-inno-hdmi-phy.yaml#
Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.example.dtb: hdmi@29590000 (starfive,jh7110-hdmi-subsystem): phy: False schema does not allow {'compatible': ['starfive,jh7110-inno-hdmi-phy'], '#clock-cells': 0, 'clocks': [[4294967295]], '#phy-cells': 0, 'phandle': 2}
	from schema $id: http://devicetree.org/schemas/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml
Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.example.dtb: /example-0/soc/hdmi@29590000/phy: failed to match any schema with compatible: ['starfive,jh7110-inno-hdmi-phy']

doc reference errors (make refcheckdocs):

See https://patchwork.kernel.org/project/devicetree/patch/20261029-jh7110-clean-send-v6-4-759594e43acf@samsung.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v6 04/18] dt-bindings: soc: starfive: Add starfive,jh7110-hdmi-subsystem

[Michal Wilczynski]

On 10/29/26 18:38, Rob Herring (Arm) wrote:
> 
> On Thu, 29 Oct 2026 08:53:38 +0100, Michal Wilczynski wrote:
>> Add the dt-binding for the StarFive JH7110 HDMI subsystem.
>>
>> The JH7110 HDMI IP is a monolithic block containing both the digital
>> controller and analog PHY in a single register space. This binding
>> defines the parent device, which holds the shared register map, and its
>> two children: the PHY and the controller.
>>
>> The two have separate resources. The PHY takes the 24 MHz reference
>> clock and provides both the pixel clock, which the VOUT clock generator
>> routes on to the display controller, and the phy the controller uses.
>> The controller takes its clocks from the VOUT clock generator. What
>> they share is the register space, which the parent maps.
>>
>> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
>> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
>> ---
>>  .../starfive/starfive,jh7110-hdmi-subsystem.yaml   | 95 ++++++++++++++++++++++
>>  1 file changed, 95 insertions(+)
>>
> 
> My bot found errors running 'make dt_binding_check' on your patch:
> 
> yamllint warnings/errors:
> 
> dtschema/dtc warnings/errors:
> /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml: Unresolvable reference: /schemas/phy/starfive,jh7110-inno-hdmi-phy.yaml#
> Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.example.dtb: hdmi@29590000 (starfive,jh7110-hdmi-subsystem): phy: False schema does not allow {'compatible': ['starfive,jh7110-inno-hdmi-phy'], '#clock-cells': 0, 'clocks': [[4294967295]], '#phy-cells': 0, 'phandle': 2}
> 	from schema $id: https://protect2.fireeye.com/v1/url?k=e93a78e1-88b16dd1-e93bf3ae-000babffaa23-e7f80dd3ed8ff65f&q=1&e=27d4095f-5012-49f1-94e3-a63fd9693348&u=http%3A%2F%2Fdevicetree.org%2Fschemas%2Fsoc%2Fstarfive%2Fstarfive%2Cjh7110-hdmi-subsystem.yaml
> Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.example.dtb: /example-0/soc/hdmi@29590000/phy: failed to match any schema with compatible: ['starfive,jh7110-inno-hdmi-phy']
> 

This patch depends on the JH7110 HDMI PHY series which adds
starfive,jh7110-inno-hdmi-phy.yaml [1].

With that series applied dt_binding_check is clean.

[1] - https://lore.kernel.org/all/20261028-jh7110-inno-hdmi-phy-v6-0-f3379684d97e@samsung.com/

Best regards,
-- 
Michal Wilczynski <m.wilczynski@samsung.com>

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v6 04/18] dt-bindings: soc: starfive: Add starfive,jh7110-hdmi-subsystem

[Rob Herring]

On Thu, Oct 29, 2026 at 06:53:25PM +0100, Michal Wilczynski wrote:
> 
> 
> On 10/29/26 18:38, Rob Herring (Arm) wrote:
> > 
> > On Thu, 29 Oct 2026 08:53:38 +0100, Michal Wilczynski wrote:
> >> Add the dt-binding for the StarFive JH7110 HDMI subsystem.
> >>
> >> The JH7110 HDMI IP is a monolithic block containing both the digital
> >> controller and analog PHY in a single register space. This binding
> >> defines the parent device, which holds the shared register map, and its
> >> two children: the PHY and the controller.
> >>
> >> The two have separate resources. The PHY takes the 24 MHz reference
> >> clock and provides both the pixel clock, which the VOUT clock generator
> >> routes on to the display controller, and the phy the controller uses.
> >> The controller takes its clocks from the VOUT clock generator. What
> >> they share is the register space, which the parent maps.
> >>
> >> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
> >> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
> >> ---
> >>  .../starfive/starfive,jh7110-hdmi-subsystem.yaml   | 95 ++++++++++++++++++++++
> >>  1 file changed, 95 insertions(+)
> >>
> > 
> > My bot found errors running 'make dt_binding_check' on your patch:
> > 
> > yamllint warnings/errors:
> > 
> > dtschema/dtc warnings/errors:
> > /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml: Unresolvable reference: /schemas/phy/starfive,jh7110-inno-hdmi-phy.yaml#
> > Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.example.dtb: hdmi@29590000 (starfive,jh7110-hdmi-subsystem): phy: False schema does not allow {'compatible': ['starfive,jh7110-inno-hdmi-phy'], '#clock-cells': 0, 'clocks': [[4294967295]], '#phy-cells': 0, 'phandle': 2}
> > 	from schema $id: https://protect2.fireeye.com/v1/url?k=e93a78e1-88b16dd1-e93bf3ae-000babffaa23-e7f80dd3ed8ff65f&q=1&e=27d4095f-5012-49f1-94e3-a63fd9693348&u=http%3A%2F%2Fdevicetree.org%2Fschemas%2Fsoc%2Fstarfive%2Fstarfive%2Cjh7110-hdmi-subsystem.yaml
> > Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.example.dtb: /example-0/soc/hdmi@29590000/phy: failed to match any schema with compatible: ['starfive,jh7110-inno-hdmi-phy']
> > 
> 
> This patch depends on the JH7110 HDMI PHY series which adds
> starfive,jh7110-inno-hdmi-phy.yaml [1].

I'm aware. I just want whomever applies this to know they need to wait 
for that series.

> With that series applied dt_binding_check is clean.

Humm, this is applied with b4 and you added the dependencies for 
it (thanks!), so it should have run with that series applied too. I'll 
have to investigate.

Rob

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v6 04/18] dt-bindings: soc: starfive: Add starfive,jh7110-hdmi-subsystem

[Conor Dooley]

[-- Attachment #1.1: Type: text/plain, Size: 4675 bytes --]

On Thu, Oct 29, 2026 at 08:53:38AM +0100, Michal Wilczynski wrote:
> Add the dt-binding for the StarFive JH7110 HDMI subsystem.
> 
> The JH7110 HDMI IP is a monolithic block containing both the digital
> controller and analog PHY in a single register space. This binding
> defines the parent device, which holds the shared register map, and its
> two children: the PHY and the controller.
> 
> The two have separate resources. The PHY takes the 24 MHz reference
> clock and provides both the pixel clock, which the VOUT clock generator
> routes on to the display controller, and the phy the controller uses.
> The controller takes its clocks from the VOUT clock generator. What
> they share is the register space, which the parent maps.
> 
> Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
> ---
>  .../starfive/starfive,jh7110-hdmi-subsystem.yaml   | 95 ++++++++++++++++++++++
>  1 file changed, 95 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml b/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml
> new file mode 100644
> index 0000000000000000000000000000000000000000..2ff8b0b920aec41a83f0aeaa0ed9c4249fe87f46
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml

Why is this in bindings/soc? I feel like it should be in
bindings/display or something along those lines, since it's the display
subsystem of the device?

Cheers,
Conor.

> @@ -0,0 +1,95 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: StarFive JH7110 HDMI subsystem
> +
> +maintainers:
> +  - Michal Wilczynski <m.wilczynski@samsung.com>
> +
> +description:
> +  The StarFive JH7110 HDMI block is a monolithic IP containing both
> +  the digital controller logic and the analog PHY logic in a single
> +  register space. It sits inside the video output subsystem, which owns
> +  the NoC bus clock and reset gating this region and the power domain it
> +  belongs to.
> +
> +properties:
> +  compatible:
> +    const: starfive,jh7110-hdmi-subsystem
> +
> +  reg:
> +    maxItems: 1
> +
> +  phy:
> +    $ref: /schemas/phy/starfive,jh7110-inno-hdmi-phy.yaml#
> +
> +  controller:
> +    $ref: /schemas/display/bridge/starfive,jh7110-inno-hdmi-controller.yaml#
> +
> +required:
> +  - compatible
> +  - reg
> +  - phy
> +  - controller
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/starfive,jh7110-crg.h>
> +    #include <dt-bindings/reset/starfive,jh7110-crg.h>
> +
> +    soc {
> +        #address-cells = <1>;
> +        #size-cells = <1>;
> +
> +        hdmi@29590000 {
> +            compatible = "starfive,jh7110-hdmi-subsystem";
> +            reg = <0x29590000 0x4000>;
> +
> +            controller {
> +                compatible = "starfive,jh7110-inno-hdmi-controller";
> +                clocks = <&voutcrg JH7110_VOUTCLK_HDMI_TX_SYS>,
> +                         <&voutcrg JH7110_VOUTCLK_HDMI_TX_MCLK>,
> +                         <&voutcrg JH7110_VOUTCLK_HDMI_TX_BCLK>,
> +                         <&hdmi_phy>;
> +                clock-names = "pclk", "mclk", "bclk", "pixel";
> +                interrupts = <99>;
> +                phys = <&hdmi_phy>;
> +                resets = <&voutcrg JH7110_VOUTRST_HDMI_TX_HDMI>;
> +                starfive,vout-syscon = <&vout_syscon>;
> +
> +                ports {
> +                    #address-cells = <1>;
> +                    #size-cells = <0>;
> +
> +                    port@0 {
> +                        reg = <0>;
> +
> +                        endpoint {
> +                            remote-endpoint = <&dpu_out_dpi0>;
> +                        };
> +                    };
> +
> +                    port@1 {
> +                        reg = <1>;
> +
> +                        endpoint {
> +                            remote-endpoint = <&hdmi_con_in>;
> +                        };
> +                    };
> +                };
> +            };
> +
> +            hdmi_phy: phy {
> +                compatible = "starfive,jh7110-inno-hdmi-phy";
> +                #clock-cells = <0>;
> +                clocks = <&xin24m>;
> +                #phy-cells = <0>;
> +            };
> +        };
> +    };
> +...
> 
> -- 
> 2.34.1
> 

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 161 bytes --]

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 05/18] dt-bindings: soc: starfive: Add starfive,jh7110-vout-syscon

[Michal Wilczynski]

The video output subsystem has its own system controller, documented as
dom_vout_syscon. Among other things it holds the mux that selects which
DC8200 output drives the HDMI transmitter, so the HDMI controller needs
to reach it.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 .../devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml         | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml b/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
index 0039319e91fe6e6aadc4300114626348e4dfb7ce..cf9b657d0e8a3ed5c5688336fee4123e14a2ac58 100644
--- a/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
+++ b/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
@@ -24,6 +24,7 @@ properties:
           - enum:
               - starfive,jh7110-aon-syscon
               - starfive,jh7110-stg-syscon
+              - starfive,jh7110-vout-syscon
           - const: syscon
 
   reg:

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 06/18] dt-bindings: display: verisilicon: Add starfive,jh7110-dc8200

[Michal Wilczynski]

The JH7110 embeds a DC8200. The binding requires an SoC specific
compatible ahead of the generic one, so add the JH7110 to the enum.

Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 Documentation/devicetree/bindings/display/verisilicon,dc.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/display/verisilicon,dc.yaml b/Documentation/devicetree/bindings/display/verisilicon,dc.yaml
index 919a9001220120054cb62d1d01b7293367266f95..05a202633cd273fec358c095c64584d959d96d90 100644
--- a/Documentation/devicetree/bindings/display/verisilicon,dc.yaml
+++ b/Documentation/devicetree/bindings/display/verisilicon,dc.yaml
@@ -16,6 +16,7 @@ properties:
   compatible:
     items:
       - enum:
+          - starfive,jh7110-dc8200
           - thead,th1520-dc8200
       - const: verisilicon,dc # DC IPs have discoverable ID/revision registers
 

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 07/18] dt-bindings: soc: starfive: Add starfive,jh7110-vout-subsystem

[Michal Wilczynski]

The JH7110 groups its display hardware into a video output subsystem,
dom_vout_top, covering the DC8200, the HDMI transmitter, the video
output clock generator and the video output system controller.

They share one NoC port whose clock and reset gate access to every
register in the region, and the region sits in the PD_VOUT power
domain. Describe the subsystem as a bus node so those resources are
owned by the block that shares them.

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 .../starfive/starfive,jh7110-vout-subsystem.yaml   | 218 +++++++++++++++++++++
 1 file changed, 218 insertions(+)

diff --git a/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-vout-subsystem.yaml b/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-vout-subsystem.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..3306c4068493ec30b3863db6ff7eb47b13d55240
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-vout-subsystem.yaml
@@ -0,0 +1,218 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/starfive/starfive,jh7110-vout-subsystem.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 video output subsystem
+
+maintainers:
+  - Michal Wilczynski <m.wilczynski@samsung.com>
+
+description:
+  The JH7110 groups its display hardware into a video output subsystem, named
+  dom_vout_top in the documentation. It covers the DC8200 display controller,
+  the HDMI transmitter, the video output clock generator and the video output
+  system controller, all behind one NoC port. That port's clock and reset gate
+  access to every register in the region, and the region sits in the PD_VOUT
+  power domain, so this node owns those resources on behalf of its children.
+
+properties:
+  compatible:
+    const: starfive,jh7110-vout-subsystem
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+    description: NoC display bus clock.
+
+  resets:
+    maxItems: 1
+    description: NoC display bus reset.
+
+  power-domains:
+    maxItems: 1
+
+  dma-noncoherent: true
+
+  ranges: true
+
+  "#address-cells":
+    const: 2
+
+  "#size-cells":
+    const: 2
+
+patternProperties:
+  "^display@[0-9a-f]+$":
+    type: object
+    additionalProperties: true
+    properties:
+      compatible:
+        contains:
+          const: starfive,jh7110-dc8200
+
+  "^hdmi@[0-9a-f]+$":
+    type: object
+    additionalProperties: true
+    properties:
+      compatible:
+        const: starfive,jh7110-hdmi-subsystem
+
+  "^syscon@[0-9a-f]+$":
+    type: object
+    additionalProperties: true
+    properties:
+      compatible:
+        contains:
+          const: starfive,jh7110-vout-syscon
+
+  "^clock-controller@[0-9a-f]+$":
+    type: object
+    additionalProperties: true
+    properties:
+      compatible:
+        const: starfive,jh7110-voutcrg
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - resets
+  - power-domains
+  - ranges
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/starfive,jh7110-crg.h>
+    #include <dt-bindings/power/starfive,jh7110-pmu.h>
+    #include <dt-bindings/reset/starfive,jh7110-crg.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        display-subsystem@29400000 {
+            compatible = "starfive,jh7110-vout-subsystem";
+            reg = <0x0 0x29400000 0x0 0x200000>;
+            ranges;
+            #address-cells = <2>;
+            clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_DISP_AXI>;
+            dma-noncoherent;
+            power-domains = <&pwrc JH7110_PD_VOUT>;
+            resets = <&syscrg JH7110_SYSRST_NOC_BUS_DISP_AXI>;
+            #size-cells = <2>;
+
+            display@29400000 {
+                compatible = "starfive,jh7110-dc8200", "verisilicon,dc";
+                reg = <0x0 0x29400000 0x0 0x2800>;
+                clocks = <&voutcrg JH7110_VOUTCLK_DC8200_CORE>,
+                         <&voutcrg JH7110_VOUTCLK_DC8200_AXI>,
+                         <&voutcrg JH7110_VOUTCLK_DC8200_AHB>,
+                         <&voutcrg JH7110_VOUTCLK_DC8200_PIX0>,
+                         <&voutcrg JH7110_VOUTCLK_DC8200_PIX1>;
+                clock-names = "core", "axi", "ahb", "pix0", "pix1";
+                interrupts = <95>;
+                resets = <&voutcrg JH7110_VOUTRST_DC8200_CORE>,
+                         <&voutcrg JH7110_VOUTRST_DC8200_AXI>,
+                         <&voutcrg JH7110_VOUTRST_DC8200_AHB>;
+                reset-names = "core", "axi", "ahb";
+
+                ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                        reg = <0>;
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        dpu_out_dpi0: endpoint@0 {
+                            reg = <0>;
+                            remote-endpoint = <&hdmi_in>;
+                        };
+                    };
+
+                    port@1 {
+                        reg = <1>;
+                    };
+                };
+            };
+
+            hdmi@29590000 {
+                compatible = "starfive,jh7110-hdmi-subsystem";
+                reg = <0x0 0x29590000 0x0 0x4000>;
+
+                controller {
+                    compatible = "starfive,jh7110-inno-hdmi-controller";
+                    clocks = <&voutcrg JH7110_VOUTCLK_HDMI_TX_SYS>,
+                             <&voutcrg JH7110_VOUTCLK_HDMI_TX_MCLK>,
+                             <&voutcrg JH7110_VOUTCLK_HDMI_TX_BCLK>,
+                             <&hdmi_phy>;
+                    clock-names = "pclk", "mclk", "bclk", "pixel";
+                    interrupts = <99>;
+                    phys = <&hdmi_phy>;
+                    resets = <&voutcrg JH7110_VOUTRST_HDMI_TX_HDMI>;
+                    starfive,vout-syscon = <&vout_syscon>;
+
+                    ports {
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        port@0 {
+                            reg = <0>;
+
+                            hdmi_in: endpoint {
+                                remote-endpoint = <&dpu_out_dpi0>;
+                            };
+                        };
+
+                        port@1 {
+                            reg = <1>;
+
+                            endpoint {
+                                remote-endpoint = <&hdmi_con_in>;
+                            };
+                        };
+                    };
+                };
+
+                hdmi_phy: phy {
+                    compatible = "starfive,jh7110-inno-hdmi-phy";
+                    #clock-cells = <0>;
+                    clocks = <&xin24m>;
+                    #phy-cells = <0>;
+                };
+            };
+
+            vout_syscon: syscon@295b0000 {
+                compatible = "starfive,jh7110-vout-syscon", "syscon";
+                reg = <0x0 0x295b0000 0x0 0x10000>;
+            };
+
+            voutcrg: clock-controller@295c0000 {
+                compatible = "starfive,jh7110-voutcrg";
+                reg = <0x0 0x295c0000 0x0 0x10000>;
+                #clock-cells = <1>;
+                clocks = <&syscrg JH7110_SYSCLK_VOUT_SRC>,
+                         <&syscrg JH7110_SYSCLK_VOUT_TOP_AHB>,
+                         <&syscrg JH7110_SYSCLK_VOUT_TOP_AXI>,
+                         <&syscrg JH7110_SYSCLK_VOUT_TOP_HDMITX0_MCLK>,
+                         <&syscrg JH7110_SYSCLK_I2STX0_BCLK>,
+                         <&hdmi_phy>;
+                clock-names = "vout_src", "vout_top_ahb",
+                              "vout_top_axi", "vout_top_hdmitx0_mclk",
+                              "i2stx0_bclk", "hdmitx0_pixelclk";
+                power-domains = <&pwrc JH7110_PD_VOUT>;
+                #reset-cells = <1>;
+                resets = <&syscrg JH7110_SYSRST_VOUT_TOP_SRC>;
+            };
+        };
+    };
+...

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 08/18] drm/bridge: inno-hdmi: Split probe out of bind

[Michal Wilczynski]

inno_hdmi_bind() both sets up the bridge and attaches it to a DRM
encoder. A platform whose HDMI controller is a child of a larger device
needs the first half without the second, since it registers as its own
platform driver and lets the DRM core bind the bridge later.

Move the setup into a new exported inno_hdmi_probe(), and reduce
inno_hdmi_bind() to a wrapper around it. Like inno_hdmi_probe() and
dw_hdmi_bind(), it now takes the platform_device, so the Rockchip glue
does the to_platform_device() conversion instead.

No functional change intended.

Reviewed-by: Joshua Peisach <jpeisach@ubuntu.com>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/gpu/drm/bridge/inno-hdmi.c            | 39 +++++++++++++++++++++++----
 drivers/gpu/drm/rockchip/inno_hdmi-rockchip.c |  2 +-
 include/drm/bridge/inno_hdmi.h                |  6 ++++-
 3 files changed, 40 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
index d29832249b942dec84fb9d07a0b21ee751fc0486..222f6522844ee60ae9a07ab2dcca748dbf7403e4 100644
--- a/drivers/gpu/drm/bridge/inno-hdmi.c
+++ b/drivers/gpu/drm/bridge/inno-hdmi.c
@@ -1067,11 +1067,24 @@ static struct i2c_adapter *inno_hdmi_i2c_adapter(struct inno_hdmi *hdmi)
 	return adap;
 }
 
-struct inno_hdmi *inno_hdmi_bind(struct device *dev,
-				 struct drm_encoder *encoder,
-				 const struct inno_hdmi_plat_data *plat_data)
+/**
+ * inno_hdmi_probe - Internal helper to perform common setup
+ * @pdev: platform device
+ * @plat_data: SoC-specific platform data
+ *
+ * This function handles all the common hardware setup: allocating the main
+ * struct, mapping registers, getting clocks, initializing the hardware,
+ * setting up the IRQ, and initializing the DDC adapter and bridge struct.
+ *
+ * It registers the bridge but does not attach it, for glue drivers that probe
+ * as their own platform device rather than through a component bind.
+ *
+ * Return: the inno_hdmi instance on success, or an ERR_PTR() on failure.
+ */
+struct inno_hdmi *inno_hdmi_probe(struct platform_device *pdev,
+				  const struct inno_hdmi_plat_data *plat_data)
 {
-	struct platform_device *pdev = to_platform_device(dev);
+	struct device *dev = &pdev->dev;
 	struct inno_hdmi *hdmi;
 	int irq;
 	int ret;
@@ -1134,7 +1147,23 @@ struct inno_hdmi *inno_hdmi_bind(struct device *dev,
 	if (ret)
 		return ERR_PTR(ret);
 
-	ret = drm_bridge_attach(encoder, &hdmi->bridge, NULL, DRM_BRIDGE_ATTACH_NO_CONNECTOR);
+	return hdmi;
+}
+EXPORT_SYMBOL_GPL(inno_hdmi_probe);
+
+struct inno_hdmi *inno_hdmi_bind(struct platform_device *pdev,
+				 struct drm_encoder *encoder,
+				 const struct inno_hdmi_plat_data *plat_data)
+{
+	struct inno_hdmi *hdmi;
+	int ret;
+
+	hdmi = inno_hdmi_probe(pdev, plat_data);
+	if (IS_ERR(hdmi))
+		return hdmi;
+
+	ret = drm_bridge_attach(encoder, &hdmi->bridge, NULL,
+				DRM_BRIDGE_ATTACH_NO_CONNECTOR);
 	if (ret)
 		return ERR_PTR(ret);
 
diff --git a/drivers/gpu/drm/rockchip/inno_hdmi-rockchip.c b/drivers/gpu/drm/rockchip/inno_hdmi-rockchip.c
index 33ff195bd2e65367792710ed2bcfb2f7c217d8e6..1f04489477e07f61e8793e08e03e73566366c725 100644
--- a/drivers/gpu/drm/rockchip/inno_hdmi-rockchip.c
+++ b/drivers/gpu/drm/rockchip/inno_hdmi-rockchip.c
@@ -127,7 +127,7 @@ static int inno_hdmi_rockchip_bind(struct device *dev, struct device *master, vo
 
 	dev_set_drvdata(dev, hdmi);
 
-	hdmi->base = inno_hdmi_bind(dev, encoder, plat_data);
+	hdmi->base = inno_hdmi_bind(to_platform_device(dev), encoder, plat_data);
 
 	connector = drm_bridge_connector_init(drm, encoder);
 	if (IS_ERR(connector)) {
diff --git a/include/drm/bridge/inno_hdmi.h b/include/drm/bridge/inno_hdmi.h
index 5bbcaeea94e2a20fd0dc0ae0c6946eb5604bbaf6..507d5e999183ca02e7dcbe4ce7568acc21426a89 100644
--- a/include/drm/bridge/inno_hdmi.h
+++ b/include/drm/bridge/inno_hdmi.h
@@ -12,6 +12,7 @@ struct device;
 struct drm_encoder;
 struct drm_display_mode;
 struct inno_hdmi;
+struct platform_device;
 
 struct inno_hdmi_plat_ops {
 	void (*enable)(struct device *pdev, struct drm_display_mode *mode);
@@ -29,7 +30,10 @@ struct inno_hdmi_plat_data {
 	struct inno_hdmi_phy_config *default_phy_config;
 };
 
-struct inno_hdmi *inno_hdmi_bind(struct device *pdev,
+struct inno_hdmi *inno_hdmi_bind(struct platform_device *pdev,
 				 struct drm_encoder *encoder,
 				 const struct inno_hdmi_plat_data *plat_data);
+
+struct inno_hdmi *inno_hdmi_probe(struct platform_device *pdev,
+				  const struct inno_hdmi_plat_data *plat_data);
 #endif /* __INNO_HDMI__ */

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 09/18] drm/bridge: inno-hdmi: Allow the register map to come from a parent

[Michal Wilczynski]

On some SoCs the HDMI controller does not own its register window. The
StarFive JH7110 documents one 64 KB block, u0_hdmitx, that holds both
the controller and the PHY, so the parent device maps it and owns the
regmap while the two children share it.

Use a regmap supplied by the parent device when there is one, and keep
mapping our own resource when there is not, so platforms that own their
register window are unaffected.

Reviewed-by: Joshua Peisach <jpeisach@ubuntu.com>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/gpu/drm/bridge/inno-hdmi.c | 31 ++++++++++++++++++++++++++++---
 1 file changed, 28 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
index 222f6522844ee60ae9a07ab2dcca748dbf7403e4..a8905bf627a224d7e3918514195f1810164dc26f 100644
--- a/drivers/gpu/drm/bridge/inno-hdmi.c
+++ b/drivers/gpu/drm/bridge/inno-hdmi.c
@@ -397,6 +397,7 @@ struct inno_hdmi {
 	struct clk *pclk;
 	struct clk *refclk;
 	void __iomem *regs;
+	struct regmap *regmap;
 	struct regmap *grf;
 
 	struct inno_hdmi_i2c *i2c;
@@ -470,11 +471,25 @@ static int inno_hdmi_find_phy_config(struct inno_hdmi *hdmi,
 
 static inline u8 hdmi_readb(struct inno_hdmi *hdmi, u16 offset)
 {
+	u32 val;
+
+	if (hdmi->regmap) {
+		if (regmap_read(hdmi->regmap, offset * 4, &val))
+			return 0;
+
+		return val;
+	}
+
 	return readl_relaxed(hdmi->regs + (offset) * 0x04);
 }
 
 static inline void hdmi_writeb(struct inno_hdmi *hdmi, u16 offset, u32 val)
 {
+	if (hdmi->regmap) {
+		regmap_write(hdmi->regmap, offset * 4, val);
+		return;
+	}
+
 	writel_relaxed(val, hdmi->regs + (offset) * 0x04);
 }
 
@@ -1101,9 +1116,19 @@ struct inno_hdmi *inno_hdmi_probe(struct platform_device *pdev,
 	hdmi->dev = dev;
 	hdmi->plat_data = plat_data;
 
-	hdmi->regs = devm_platform_ioremap_resource(pdev, 0);
-	if (IS_ERR(hdmi->regs))
-		return ERR_CAST(hdmi->regs);
+	/*
+	 * On platforms where the controller shares a register space with
+	 * other blocks, the parent owns the regmap. Fall back to mapping
+	 * our own resource where it does not.
+	 */
+	if (dev->parent)
+		hdmi->regmap = dev_get_regmap(dev->parent, NULL);
+
+	if (!hdmi->regmap) {
+		hdmi->regs = devm_platform_ioremap_resource(pdev, 0);
+		if (IS_ERR(hdmi->regs))
+			return ERR_CAST(hdmi->regs);
+	}
 
 	hdmi->pclk = devm_clk_get_enabled(hdmi->dev, "pclk");
 	if (IS_ERR(hdmi->pclk)) {

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v6 09/18] drm/bridge: inno-hdmi: Allow the register map to come from a parent

[Heiko Stuebner]

Am Donnerstag, 29. Oktober 2026, 08:53:43 Mitteleuropäische Normalzeit schrieb Michal Wilczynski:
> On some SoCs the HDMI controller does not own its register window. The
> StarFive JH7110 documents one 64 KB block, u0_hdmitx, that holds both
> the controller and the PHY, so the parent device maps it and owns the
> regmap while the two children share it.
> 
> Use a regmap supplied by the parent device when there is one, and keep
> mapping our own resource when there is not, so platforms that own their
> register window are unaffected.
> 
> Reviewed-by: Joshua Peisach <jpeisach@ubuntu.com>
> Tested-by: Byron Stanoszek <gandalf@winds.org>
> Tested-by: OOHehir <oo.hehir@gmail.com>
> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
> ---
>  drivers/gpu/drm/bridge/inno-hdmi.c | 31 ++++++++++++++++++++++++++++---
>  1 file changed, 28 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
> index 222f6522844ee60ae9a07ab2dcca748dbf7403e4..a8905bf627a224d7e3918514195f1810164dc26f 100644
> --- a/drivers/gpu/drm/bridge/inno-hdmi.c
> +++ b/drivers/gpu/drm/bridge/inno-hdmi.c
> @@ -397,6 +397,7 @@ struct inno_hdmi {
>  	struct clk *pclk;
>  	struct clk *refclk;
>  	void __iomem *regs;
> +	struct regmap *regmap;
>  	struct regmap *grf;
>  
>  	struct inno_hdmi_i2c *i2c;
> @@ -470,11 +471,25 @@ static int inno_hdmi_find_phy_config(struct inno_hdmi *hdmi,
>  
>  static inline u8 hdmi_readb(struct inno_hdmi *hdmi, u16 offset)
>  {
> +	u32 val;
> +
> +	if (hdmi->regmap) {
> +		if (regmap_read(hdmi->regmap, offset * 4, &val))
> +			return 0;
> +
> +		return val;
> +	}
> +
>  	return readl_relaxed(hdmi->regs + (offset) * 0x04);
>  }
>  
>  static inline void hdmi_writeb(struct inno_hdmi *hdmi, u16 offset, u32 val)
>  {
> +	if (hdmi->regmap) {
> +		regmap_write(hdmi->regmap, offset * 4, val);
> +		return;
> +	}
> +
>  	writel_relaxed(val, hdmi->regs + (offset) * 0x04);
>  }
>  
> @@ -1101,9 +1116,19 @@ struct inno_hdmi *inno_hdmi_probe(struct platform_device *pdev,
>  	hdmi->dev = dev;
>  	hdmi->plat_data = plat_data;
>  
> -	hdmi->regs = devm_platform_ioremap_resource(pdev, 0);
> -	if (IS_ERR(hdmi->regs))
> -		return ERR_CAST(hdmi->regs);
> +	/*
> +	 * On platforms where the controller shares a register space with
> +	 * other blocks, the parent owns the regmap. Fall back to mapping
> +	 * our own resource where it does not.
> +	 */
> +	if (dev->parent)
> +		hdmi->regmap = dev_get_regmap(dev->parent, NULL);
> +
> +	if (!hdmi->regmap) {
> +		hdmi->regs = devm_platform_ioremap_resource(pdev, 0);
> +		if (IS_ERR(hdmi->regs))
> +			return ERR_CAST(hdmi->regs);
> +	}

why can't you just also use a mmio regmap here? Because with this change
the driver now has 2 competing register interfaces and you need those
conditionals all the time.

Just convert the existing user to also use a regmap please.


Heiko




_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 10/18] drm/bridge: inno-hdmi: Add .disable platform operation

[Michal Wilczynski]

The Innosilicon HDMI driver supports platform-specific behavior through
the `inno_hdmi_plat_ops`. While it provides an `.enable` hook for
platform-specific power up sequences (like enabling PHYs), it lacks a
corresponding hook for power down.

This patch adds a new `.disable` op to the `inno_hdmi_plat_ops` struct
and calls it at the beginning of `inno_hdmi_bridge_atomic_disable()`.

This allows platform specific drivers, such as the StarFive JH7110,
to implement their own power down sequence (e.g., calling
phy_power_off() and clk_disable_unprepare()).

Reviewed-by: Joshua Peisach <jpeisach@ubuntu.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/gpu/drm/bridge/inno-hdmi.c | 4 ++++
 include/drm/bridge/inno_hdmi.h     | 1 +
 2 files changed, 5 insertions(+)

diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
index a8905bf627a224d7e3918514195f1810164dc26f..708d4c03f8880429f99680abd0c92e150312237b 100644
--- a/drivers/gpu/drm/bridge/inno-hdmi.c
+++ b/drivers/gpu/drm/bridge/inno-hdmi.c
@@ -886,6 +886,10 @@ static void inno_hdmi_bridge_atomic_disable(struct drm_bridge *bridge,
 					    struct drm_atomic_commit *state)
 {
 	struct inno_hdmi *hdmi = bridge_to_inno_hdmi(bridge);
+	const struct inno_hdmi_plat_ops *plat_ops = hdmi->plat_data->ops;
+
+	if (plat_ops && plat_ops->disable)
+		plat_ops->disable(hdmi->dev);
 
 	inno_hdmi_standby(hdmi);
 }
diff --git a/include/drm/bridge/inno_hdmi.h b/include/drm/bridge/inno_hdmi.h
index 507d5e999183ca02e7dcbe4ce7568acc21426a89..0864f0d8862a4325821a84db6d04f14011d9aa78 100644
--- a/include/drm/bridge/inno_hdmi.h
+++ b/include/drm/bridge/inno_hdmi.h
@@ -16,6 +16,7 @@ struct platform_device;
 
 struct inno_hdmi_plat_ops {
 	void (*enable)(struct device *pdev, struct drm_display_mode *mode);
+	void (*disable)(struct device *pdev);
 };
 
 struct inno_hdmi_phy_config {

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 11/18] drm/bridge: inno-hdmi: Add .mode_valid platform operation

[Michal Wilczynski]

inno_hdmi_bridge_mode_valid() validates the pixel clock against
hdmi->refclk, but that clock is optional and is only present on
platforms that describe a "ref" clock. Platforms where the pixel clock
is produced by a separate device - such as the StarFive JH7110, whose
PHY is both the clock and the PHY provider - have no "ref" clock, so
the check is skipped entirely and every mode is reported as valid.

A mode the platform cannot generate is then advertised to userspace.
The subsequent modeset appears to succeed, since the atomic enable path
cannot fail, and the display silently stays blank.

Add a .mode_valid platform operation so platforms can reject modes they
are unable to drive. Platforms that do not implement it are unaffected.

Reviewed-by: Joshua Peisach <jpeisach@ubuntu.com>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/gpu/drm/bridge/inno-hdmi.c | 9 +++++++++
 include/drm/bridge/inno_hdmi.h     | 5 ++++-
 2 files changed, 13 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
index 708d4c03f8880429f99680abd0c92e150312237b..2684a3cc5667ce133357dccb8d214806db27f863 100644
--- a/drivers/gpu/drm/bridge/inno-hdmi.c
+++ b/drivers/gpu/drm/bridge/inno-hdmi.c
@@ -823,6 +823,7 @@ static enum drm_mode_status inno_hdmi_bridge_mode_valid(struct drm_bridge *bridg
 							const struct drm_display_mode *mode)
 {
 	struct inno_hdmi *hdmi = bridge_to_inno_hdmi(bridge);
+	const struct inno_hdmi_plat_ops *plat_ops = hdmi->plat_data->ops;
 	unsigned long mpixelclk, max_tolerance;
 	long rounded_refclk;
 
@@ -838,6 +839,14 @@ static enum drm_mode_status inno_hdmi_bridge_mode_valid(struct drm_bridge *bridg
 	if (inno_hdmi_find_phy_config(hdmi, mpixelclk) < 0)
 		return MODE_CLOCK_HIGH;
 
+	if (plat_ops && plat_ops->mode_valid) {
+		enum drm_mode_status status;
+
+		status = plat_ops->mode_valid(hdmi->dev, mode);
+		if (status != MODE_OK)
+			return status;
+	}
+
 	if (hdmi->refclk) {
 		rounded_refclk = clk_round_rate(hdmi->refclk, mpixelclk);
 		if (rounded_refclk < 0)
diff --git a/include/drm/bridge/inno_hdmi.h b/include/drm/bridge/inno_hdmi.h
index 0864f0d8862a4325821a84db6d04f14011d9aa78..790633fcea97a6b9840da7b19a0c0b0d7271fb83 100644
--- a/include/drm/bridge/inno_hdmi.h
+++ b/include/drm/bridge/inno_hdmi.h
@@ -8,15 +8,18 @@
 
 #include <linux/types.h>
 
+#include <drm/drm_modes.h>
+
 struct device;
 struct drm_encoder;
-struct drm_display_mode;
 struct inno_hdmi;
 struct platform_device;
 
 struct inno_hdmi_plat_ops {
 	void (*enable)(struct device *pdev, struct drm_display_mode *mode);
 	void (*disable)(struct device *pdev);
+	enum drm_mode_status (*mode_valid)(struct device *pdev,
+					   const struct drm_display_mode *mode);
 };
 
 struct inno_hdmi_phy_config {

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 12/18] drm/bridge: inno-hdmi: Make the PHY configuration table optional

[Michal Wilczynski]

The pre-emphasis and drive-strength values in inno_hdmi_phy_config, and
the registers they are written to, belong to the PHY integrated into the
controller. A platform whose PHY is a separate device has neither, and
its own .mode_valid already validates the pixel clock against the real
PHY, so the table only bounds the generic check.

Let such a platform omit the table: skip the integrated-PHY register
writes in the power-up path and the table lookup in .mode_valid when it
is absent. Platforms that supply one are unaffected.

Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/gpu/drm/bridge/inno-hdmi.c | 19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
index 2684a3cc5667ce133357dccb8d214806db27f863..42a3cd450e0f56a0b06d187645522624feb8918d 100644
--- a/drivers/gpu/drm/bridge/inno-hdmi.c
+++ b/drivers/gpu/drm/bridge/inno-hdmi.c
@@ -538,8 +538,14 @@ static void inno_hdmi_power_up(struct inno_hdmi *hdmi,
 			       unsigned long mpixelclock)
 {
 	struct inno_hdmi_phy_config *phy_config;
-	int ret = inno_hdmi_find_phy_config(hdmi, mpixelclock);
+	int ret;
+
+	inno_hdmi_sys_power(hdmi, false);
+
+	if (!hdmi->plat_data->phy_configs)
+		goto out;
 
+	ret = inno_hdmi_find_phy_config(hdmi, mpixelclock);
 	if (ret < 0) {
 		phy_config = hdmi->plat_data->default_phy_config;
 		DRM_DEV_ERROR(hdmi->dev,
@@ -549,8 +555,6 @@ static void inno_hdmi_power_up(struct inno_hdmi *hdmi,
 		phy_config = &hdmi->plat_data->phy_configs[ret];
 	}
 
-	inno_hdmi_sys_power(hdmi, false);
-
 	hdmi_writeb(hdmi, HDMI_PHY_PRE_EMPHASIS, phy_config->pre_emphasis);
 	hdmi_writeb(hdmi, HDMI_PHY_DRIVER, phy_config->voltage_level_control);
 	hdmi_writeb(hdmi, HDMI_PHY_SYS_CTL, 0x15);
@@ -560,6 +564,7 @@ static void inno_hdmi_power_up(struct inno_hdmi *hdmi,
 	hdmi_writeb(hdmi, HDMI_PHY_SYNC, 0x00);
 	hdmi_writeb(hdmi, HDMI_PHY_SYNC, 0x01);
 
+out:
 	inno_hdmi_sys_power(hdmi, true);
 };
 
@@ -836,7 +841,8 @@ static enum drm_mode_status inno_hdmi_bridge_mode_valid(struct drm_bridge *bridg
 	if (mpixelclk < HDMI_TMDS_CHAR_RATE_MIN_HZ)
 		return MODE_CLOCK_LOW;
 
-	if (inno_hdmi_find_phy_config(hdmi, mpixelclk) < 0)
+	if (hdmi->plat_data->phy_configs &&
+	    inno_hdmi_find_phy_config(hdmi, mpixelclk) < 0)
 		return MODE_CLOCK_HIGH;
 
 	if (plat_ops && plat_ops->mode_valid) {
@@ -1117,11 +1123,6 @@ struct inno_hdmi *inno_hdmi_probe(struct platform_device *pdev,
 	int irq;
 	int ret;
 
-	if (!plat_data->phy_configs || !plat_data->default_phy_config) {
-		dev_err(dev, "Missing platform PHY ops\n");
-		return ERR_PTR(-ENODEV);
-	}
-
 	hdmi = devm_drm_bridge_alloc(dev, struct inno_hdmi, bridge, &inno_hdmi_bridge_funcs);
 	if (IS_ERR(hdmi))
 		return ERR_CAST(hdmi);

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 13/18] drm/bridge: inno-hdmi: Make the register clock source selectable

[Michal Wilczynski]

inno_hdmi_init_hw() drives the register interface from the system clock
on every platform, by setting v_REG_CLK_SOURCE_SYS unconditionally in
HDMI_SYS_CTRL.

That is not right everywhere. On the JH7110 a Framework 13 (fml13v01)
panel flickers continuously with the system clock selected and behaves
once the TMDS clock drives the register interface instead. Maud Spierings
found this by diffing HDMI_SYS_CTRL against the StarFive vendor kernel,
which leaves the bit clear.

Add a plat_data flag for it rather than changing the bit for everyone.
The Rockchip integrations keep the system clock, so this is a no-op for
them; only a platform that asks for it gets the TMDS clock.

Reported-by: Maud Spierings <maud_spierings@murena.io>
Closes: https://lore.kernel.org/all/e780ecb8-918f-4816-99c8-b69b10b25a18@murena.io/
Tested-by: Maud Spierings <maud_spierings@murena.io>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/gpu/drm/bridge/inno-hdmi.c | 4 +++-
 include/drm/bridge/inno_hdmi.h     | 2 ++
 2 files changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/bridge/inno-hdmi.c b/drivers/gpu/drm/bridge/inno-hdmi.c
index 42a3cd450e0f56a0b06d187645522624feb8918d..66e7e08f89813b4ddcb38a3d0b296132944f06bb 100644
--- a/drivers/gpu/drm/bridge/inno-hdmi.c
+++ b/drivers/gpu/drm/bridge/inno-hdmi.c
@@ -580,7 +580,9 @@ static void inno_hdmi_init_hw(struct inno_hdmi *hdmi)
 	usleep_range(100, 150);
 
 	msk = m_REG_CLK_INV | m_REG_CLK_SOURCE | m_POWER | m_INT_POL;
-	val = v_REG_CLK_INV | v_REG_CLK_SOURCE_SYS | v_PWR_ON | v_INT_POL_HIGH;
+	val = v_REG_CLK_INV | v_PWR_ON | v_INT_POL_HIGH;
+	val |= hdmi->plat_data->reg_clk_source_tmds ? v_REG_CLK_SOURCE_TMDS :
+						      v_REG_CLK_SOURCE_SYS;
 	hdmi_modb(hdmi, HDMI_SYS_CTRL, msk, val);
 
 	inno_hdmi_standby(hdmi);
diff --git a/include/drm/bridge/inno_hdmi.h b/include/drm/bridge/inno_hdmi.h
index 790633fcea97a6b9840da7b19a0c0b0d7271fb83..cc5099d05f641eef5de91ed5becde7337c04b013 100644
--- a/include/drm/bridge/inno_hdmi.h
+++ b/include/drm/bridge/inno_hdmi.h
@@ -32,6 +32,8 @@ struct inno_hdmi_plat_data {
 	const struct inno_hdmi_plat_ops *ops;
 	struct inno_hdmi_phy_config *phy_configs;
 	struct inno_hdmi_phy_config *default_phy_config;
+	/* Clock the register interface from the TMDS clock, not the system clock. */
+	bool reg_clk_source_tmds;
 };
 
 struct inno_hdmi *inno_hdmi_bind(struct platform_device *pdev,

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 14/18] soc: starfive: Add jh7110-hdmi-subsystem driver

[Michal Wilczynski]

Add the parent driver for the monolithic JH7110 HDMI IP block.

This driver binds to the starfive,jh7110-hdmi-subsystem node. It maps the
shared register block, creates a regmap, and calls
devm_of_platform_populate() to create its hdmi_phy and hdmi_controller
child devices, which retrieve the shared regmap from this parent.

The NoC display bus clock and reset that gate access to this region, and
the PD_VOUT power domain it sits in, are held by the video output
subsystem parent for as long as this device exists, so there is nothing
for this driver to bring up itself.

Co-developed-by: Dominique Belhachemi <db@domibel.de>
Signed-off-by: Dominique Belhachemi <db@domibel.de>
Tested-by: Icenowy Zheng <zhengxingda@iscas.ac.cn>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/soc/Kconfig                          |  1 +
 drivers/soc/Makefile                         |  1 +
 drivers/soc/starfive/Kconfig                 | 27 +++++++++++
 drivers/soc/starfive/Makefile                |  2 +
 drivers/soc/starfive/jh7110-hdmi-subsystem.c | 72 ++++++++++++++++++++++++++++
 5 files changed, 103 insertions(+)

diff --git a/drivers/soc/Kconfig b/drivers/soc/Kconfig
index a2d65adffb8052c0ac5a6b60bf33fa9c644701bb..b3b01fc38139d98076c14f626a42ae3b7ef7c5d6 100644
--- a/drivers/soc/Kconfig
+++ b/drivers/soc/Kconfig
@@ -24,6 +24,7 @@ source "drivers/soc/renesas/Kconfig"
 source "drivers/soc/rockchip/Kconfig"
 source "drivers/soc/samsung/Kconfig"
 source "drivers/soc/sophgo/Kconfig"
+source "drivers/soc/starfive/Kconfig"
 source "drivers/soc/sunxi/Kconfig"
 source "drivers/soc/tegra/Kconfig"
 source "drivers/soc/ti/Kconfig"
diff --git a/drivers/soc/Makefile b/drivers/soc/Makefile
index c9e689080ceb759384f690c2b65a82b3cb451c74..009f85ff891a15e0455f92c5d5a4059d8b1fcd3f 100644
--- a/drivers/soc/Makefile
+++ b/drivers/soc/Makefile
@@ -30,6 +30,7 @@ obj-y				+= renesas/
 obj-y				+= rockchip/
 obj-$(CONFIG_SOC_SAMSUNG)	+= samsung/
 obj-y				+= sophgo/
+obj-y				+= starfive/
 obj-y				+= sunxi/
 obj-$(CONFIG_ARCH_TEGRA)	+= tegra/
 obj-y				+= ti/
diff --git a/drivers/soc/starfive/Kconfig b/drivers/soc/starfive/Kconfig
new file mode 100644
index 0000000000000000000000000000000000000000..8cdcfc6f7848d2dd40b57afa101edcffc3f263a6
--- /dev/null
+++ b/drivers/soc/starfive/Kconfig
@@ -0,0 +1,27 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# Starfive SoC drivers
+#
+
+if ARCH_STARFIVE || COMPILE_TEST
+menu "Starfive SoC drivers"
+
+config SOC_STARFIVE_JH7110_HDMI_SUBSYSTEM
+	tristate "StarFive JH7110 HDMI subsystem driver"
+	depends on OF
+	select REGMAP_MMIO
+	help
+	  This option enables the parent driver
+	  for the monolithic StarFive JH7110 HDMI peripheral.
+
+	  The JH7110 HDMI IP block contains both the digital controller
+	  (DRM bridge) and the analog PHY (clock/phy provider) logic within
+	  a single shared register space.
+
+	  This driver acts as a wrapper. Its only job is to map the
+	  shared registers and create separate logical child devices
+	  for the "PHY" and the "controller", which have their own clocks
+	  and roles but share the register space.
+
+endmenu
+endif
diff --git a/drivers/soc/starfive/Makefile b/drivers/soc/starfive/Makefile
new file mode 100644
index 0000000000000000000000000000000000000000..be89d8119212b7a7038817c2f0e8eac1984ada88
--- /dev/null
+++ b/drivers/soc/starfive/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_SOC_STARFIVE_JH7110_HDMI_SUBSYSTEM) += jh7110-hdmi-subsystem.o
diff --git a/drivers/soc/starfive/jh7110-hdmi-subsystem.c b/drivers/soc/starfive/jh7110-hdmi-subsystem.c
new file mode 100644
index 0000000000000000000000000000000000000000..b01dc66450f516599c013df0383e6fde987f390e
--- /dev/null
+++ b/drivers/soc/starfive/jh7110-hdmi-subsystem.c
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the StarFive JH7110 HDMI subsystem
+ *
+ * Copyright (c) 2025 Samsung Electronics Co., Ltd.
+ * Author: Michal Wilczynski <m.wilczynski@samsung.com>
+ *
+ * This driver binds to the monolithic HDMI block and creates separate
+ * logical platform devices for the HDMI Controller (bridge) and the
+ * HDMI PHY (clock/phy provider), allowing them to share a single regmap.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static const struct regmap_config starfive_hdmi_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 8,
+	.max_register = 0x3fff,
+};
+
+static int starfive_hdmi_subsys_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct regmap *regmap;
+	void __iomem *regs;
+	int ret;
+
+	/*
+	 * The NoC display bus clock and reset that gate access to this region,
+	 * and the PD_VOUT power domain it sits in, are held by the video
+	 * output subsystem parent for as long as this device exists.
+	 */
+	regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(regs))
+		return PTR_ERR(regs);
+
+	regmap = devm_regmap_init_mmio(dev, regs,
+				       &starfive_hdmi_regmap_config);
+	if (IS_ERR(regmap))
+		return dev_err_probe(dev, PTR_ERR(regmap),
+				     "Failed to init shared regmap\n");
+
+	ret = devm_of_platform_populate(dev);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to populate child devices\n");
+
+	return 0;
+}
+
+static const struct of_device_id starfive_hdmi_subsys_of_match[] = {
+	{ .compatible = "starfive,jh7110-hdmi-subsystem", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, starfive_hdmi_subsys_of_match);
+
+static struct platform_driver starfive_hdmi_subsys_driver = {
+	.probe = starfive_hdmi_subsys_probe,
+	.driver = {
+		.name = "starfive-hdmi-subsystem",
+		.of_match_table = starfive_hdmi_subsys_of_match,
+	},
+};
+module_platform_driver(starfive_hdmi_subsys_driver);
+
+MODULE_AUTHOR("Michal Wilczynski <m.wilczynski@samsung.com>");
+MODULE_DESCRIPTION("StarFive JH7110 HDMI subsystem Driver");
+MODULE_LICENSE("GPL");

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 15/18] soc: starfive: Add jh7110-vout-subsystem driver

[Michal Wilczynski]

Nothing in the video output subsystem can reach its own registers until
the NoC display bus clock and reset are up and PD_VOUT is powered, and
those are shared by every device in the region. Leaving them to whichever
consumer probes first works by accident and stops working as soon as the
probe order changes.

Add a driver for the subsystem node that takes the bus clock and reset,
holds a runtime PM reference so genpd keeps PD_VOUT powered, and then
populates its children. All three are released only once the last child
is gone.

Tested-by: Icenowy Zheng <zhengxingda@iscas.ac.cn>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/soc/starfive/Kconfig                 | 15 +++++
 drivers/soc/starfive/Makefile                |  1 +
 drivers/soc/starfive/jh7110-vout-subsystem.c | 82 ++++++++++++++++++++++++++++
 3 files changed, 98 insertions(+)

diff --git a/drivers/soc/starfive/Kconfig b/drivers/soc/starfive/Kconfig
index 8cdcfc6f7848d2dd40b57afa101edcffc3f263a6..643d384c10b094d5633b5e31c3a67f5b9432c6d1 100644
--- a/drivers/soc/starfive/Kconfig
+++ b/drivers/soc/starfive/Kconfig
@@ -6,6 +6,21 @@
 if ARCH_STARFIVE || COMPILE_TEST
 menu "Starfive SoC drivers"
 
+config SOC_STARFIVE_JH7110_VOUT_SUBSYSTEM
+	tristate "StarFive JH7110 video output subsystem driver"
+	depends on OF
+	select PM
+	help
+	  This option enables the parent driver for the StarFive JH7110
+	  video output subsystem, which the documentation calls dom_vout_top.
+
+	  The subsystem covers the DC8200 display controller, the HDMI
+	  transmitter, the video output clock generator and the video output
+	  system controller. They share one NoC port whose clock and reset
+	  gate access to the whole register region, and the region sits in
+	  the PD_VOUT power domain. This driver owns those resources and
+	  holds them for as long as any of its children exist.
+
 config SOC_STARFIVE_JH7110_HDMI_SUBSYSTEM
 	tristate "StarFive JH7110 HDMI subsystem driver"
 	depends on OF
diff --git a/drivers/soc/starfive/Makefile b/drivers/soc/starfive/Makefile
index be89d8119212b7a7038817c2f0e8eac1984ada88..6c229020c1e563b37df43f6ac1665465a11333cc 100644
--- a/drivers/soc/starfive/Makefile
+++ b/drivers/soc/starfive/Makefile
@@ -1,2 +1,3 @@
 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_SOC_STARFIVE_JH7110_HDMI_SUBSYSTEM) += jh7110-hdmi-subsystem.o
+obj-$(CONFIG_SOC_STARFIVE_JH7110_VOUT_SUBSYSTEM) += jh7110-vout-subsystem.o
diff --git a/drivers/soc/starfive/jh7110-vout-subsystem.c b/drivers/soc/starfive/jh7110-vout-subsystem.c
new file mode 100644
index 0000000000000000000000000000000000000000..af632692e2139d9d07edd478a299b170ad1b7104
--- /dev/null
+++ b/drivers/soc/starfive/jh7110-vout-subsystem.c
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for the StarFive JH7110 video output subsystem
+ *
+ * Copyright (c) 2025 Samsung Electronics Co., Ltd.
+ * Author: Michal Wilczynski <m.wilczynski@samsung.com>
+ *
+ * The display hardware sits behind a single NoC port whose clock and reset
+ * gate access to every register in the region, inside the PD_VOUT power
+ * domain. Nothing below this node can reach its own registers until all three
+ * are up, so bring them up here and hold them for as long as any child device
+ * exists, rather than leaving them to whichever consumer happens to probe
+ * first.
+ */
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/reset.h>
+
+static void jh7110_vout_subsys_pm_put(void *data)
+{
+	pm_runtime_put_sync(data);
+}
+
+static int jh7110_vout_subsys_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct reset_control *bus_rst;
+	struct clk *bus_clk;
+	int ret;
+
+	/*
+	 * Take a runtime PM reference for the lifetime of this device. genpd
+	 * only keeps PD_VOUT powered while something actually holds it, and
+	 * an unclocked or unpowered access to this region wedges the bus.
+	 */
+	ret = devm_pm_runtime_enable(dev);
+	if (ret)
+		return ret;
+
+	ret = pm_runtime_resume_and_get(dev);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to power on PD_VOUT\n");
+
+	ret = devm_add_action_or_reset(dev, jh7110_vout_subsys_pm_put, dev);
+	if (ret)
+		return ret;
+
+	bus_clk = devm_clk_get_enabled(dev, NULL);
+	if (IS_ERR(bus_clk))
+		return dev_err_probe(dev, PTR_ERR(bus_clk),
+				     "Failed to enable NoC bus clock\n");
+
+	bus_rst = devm_reset_control_get_exclusive_deasserted(dev, NULL);
+	if (IS_ERR(bus_rst))
+		return dev_err_probe(dev, PTR_ERR(bus_rst),
+				     "Failed to deassert NoC bus reset\n");
+
+	return devm_of_platform_populate(dev);
+}
+
+static const struct of_device_id jh7110_vout_subsys_of_match[] = {
+	{ .compatible = "starfive,jh7110-vout-subsystem", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, jh7110_vout_subsys_of_match);
+
+static struct platform_driver jh7110_vout_subsys_driver = {
+	.probe = jh7110_vout_subsys_probe,
+	.driver = {
+		.name = "jh7110-vout-subsystem",
+		.of_match_table = jh7110_vout_subsys_of_match,
+	},
+};
+module_platform_driver(jh7110_vout_subsys_driver);
+
+MODULE_AUTHOR("Michal Wilczynski <m.wilczynski@samsung.com>");
+MODULE_DESCRIPTION("StarFive JH7110 video output subsystem driver");
+MODULE_LICENSE("GPL");

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 16/18] drm/bridge: starfive: Add JH7110 HDMI controller driver

[Michal Wilczynski]

Add the HDMI controller (bridge) driver for the StarFive JH7110.

This driver binds to the starfive,jh7110-inno-hdmi-controller node. It
gets its register access, module and bus clocks from voutcrg, and
consumes the pixel clock and the PHY from its hdmi_phy sibling.

The driver calls the generic inno_hdmi_probe function, which picks up
the regmap shared with the PHY from the parent device and registers a
DRM bridge. The .enable hook is responsible for setting the PHY's pixel
clock rate via clk_set_rate() and powering on the PHY via
phy_power_on().

The DC8200 has two panels, each exposing a DP and a DPI interface, and a
mux in the video output system controller picks which of them drives the
HDMI transmitter. It comes out of reset on panel 0 / DPI, which happens
to be what the default wiring needs, so nothing has had to program it so
far. Derive it from the port graph instead, taking the panel from the
remote port number and the interface from the remote endpoint number, so
that a board describing a different output is honoured.

The generic driver holds the clock it looks up as the register access
clock enabled for its lifetime, and derives the DDC divider from that
clock's rate, so point it at the system clock. Naming the pixel clock
there instead would keep the PHY pre-PLL powered from probe onwards and
size the divider from the wrong rate.

The PHY can only generate the discrete set of pixel clocks described by
its pre-PLL table, so .mode_valid rejects any mode clk_round_rate()
cannot satisfy. Without it such a mode would be advertised to userspace
and the modeset would appear to succeed while the display stayed blank.

.enable returns early when the rate is unsupported or the PHY fails to
power on, so track whether the pixel clock was actually enabled and let
.disable tear down only what was brought up, otherwise the clock
refcount underflows.

The clocks and the reset are torn down through devm rather than from
.remove, so that they outlive the bridge that inno_hdmi_probe() adds with
devm_drm_bridge_add(). Releasing them in .remove runs before devres
unwinds and would leave the bridge registered with its clocks already
gated.

Tested-by: Icenowy Zheng <zhengxingda@iscas.ac.cn>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 drivers/gpu/drm/bridge/Kconfig            |  11 ++
 drivers/gpu/drm/bridge/Makefile           |   1 +
 drivers/gpu/drm/bridge/jh7110-inno-hdmi.c | 296 ++++++++++++++++++++++++++++++
 3 files changed, 308 insertions(+)

diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index 4a57d49b4c6d3ab4b965228835b372d191647197..75b1cf6727d5a32310dcf9fe5734d95e14eea8fe 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -359,6 +359,17 @@ config DRM_SOLOMON_SSD2825
 	  Say M here if you want to support this hardware as a module.
 	  The module will be named "ssd2825".
 
+config DRM_STARFIVE_JH7110_INNO_HDMI
+	tristate "Starfive JH7110 Innosilicon HDMI bridge"
+	depends on OF
+	depends on ARCH_STARFIVE || COMPILE_TEST
+	select DRM_INNO_HDMI
+	help
+	  Enable support for the StarFive JH7110 specific implementation
+	  of the Innosilicon HDMI controller.
+	  This driver acts as a glue layer between the JH7110 HDMI subsystem
+	  parent driver and the generic Innosilicon HDMI bridge driver.
+
 config DRM_THINE_THC63LVD1024
 	tristate "Thine THC63LVD1024 LVDS decoder bridge"
 	depends on OF
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 15cc821d85b7ea6f3cdc313f3e521b028de567d7..5d843f4ad7ed50b28cb75286c5e22789d91a0836 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -30,6 +30,7 @@ obj-$(CONFIG_DRM_SIL_SII8620) += sil-sii8620.o
 obj-$(CONFIG_DRM_SII902X) += sii902x.o
 obj-$(CONFIG_DRM_SII9234) += sii9234.o
 obj-$(CONFIG_DRM_SIMPLE_BRIDGE) += simple-bridge.o
+obj-$(CONFIG_DRM_STARFIVE_JH7110_INNO_HDMI) += jh7110-inno-hdmi.o
 obj-$(CONFIG_DRM_SOLOMON_SSD2825) += ssd2825.o
 obj-$(CONFIG_DRM_THEAD_TH1520_DW_HDMI) += th1520-dw-hdmi.o
 obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
diff --git a/drivers/gpu/drm/bridge/jh7110-inno-hdmi.c b/drivers/gpu/drm/bridge/jh7110-inno-hdmi.c
new file mode 100644
index 0000000000000000000000000000000000000000..3ce0add73c40a75fcfeb3f542713f6f8eae513e9
--- /dev/null
+++ b/drivers/gpu/drm/bridge/jh7110-inno-hdmi.c
@@ -0,0 +1,296 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) StarFive Technology Co., Ltd.
+ * Copyright (c) 2025 Samsung Electronics Co., Ltd.
+ * Author: Michal Wilczynski <m.wilczynski@samsung.com>
+ *
+ * HDMI controller (bridge) driver for the StarFive JH7110 HDMI subsystem.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/cleanup.h>
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <drm/bridge/inno_hdmi.h>
+#include <drm/drm_modes.h>
+
+/* dom_vout_syscon: HDMI pixel data mapping */
+#define VOUT_SYSCFG_4			0x4
+#define VOUT_HDMI_DP_BIT_DEPTH		BIT(25)
+#define VOUT_HDMI_DP_YUV_MODE		GENMASK(27, 26)
+#define VOUT_HDMI_DP_YUV_MODE_RGB	3
+#define VOUT_HDMI_DPI_BIT_DEPTH		GENMASK(29, 28)
+#define VOUT_HDMI_DPI_BIT_DEPTH_8BIT	0
+#define VOUT_HDMI_DPI_DP_SEL		BIT(30)
+
+/* u2_display_panel_mux feeds HDMI_Ctrl, see the block diagram in 5.1 */
+#define VOUT_SYSCFG_8			0x8
+#define VOUT_HDMI_PANEL_SEL		BIT(4)
+
+enum stf_hdmi_ctrl_clocks { CLK_SYS = 0, CLK_M, CLK_B, CLK_PCLK, CLK_CTRL_NUM };
+
+struct stf_inno_hdmi_controller {
+	struct clk_bulk_data clks[CLK_CTRL_NUM];
+	struct reset_control *tx_rst;
+	struct phy *phy;
+	bool enabled;
+};
+
+static enum drm_mode_status
+inno_hdmi_starfive_mode_valid(struct device *dev,
+			      const struct drm_display_mode *mode)
+{
+	struct stf_inno_hdmi_controller *ctrl = dev_get_drvdata(dev);
+	unsigned long pixelclk = mode->clock * 1000;
+	long rounded;
+
+	/*
+	 * The PHY can only generate the discrete set of pixel clocks described
+	 * by its pre-PLL table, and clk_round_rate() fails for anything else.
+	 * Reject those modes here: without this the modeset would appear to
+	 * succeed while the PHY never produces a signal.
+	 */
+	rounded = clk_round_rate(ctrl->clks[CLK_PCLK].clk, pixelclk);
+	if (rounded != pixelclk)
+		return MODE_NOCLOCK;
+
+	return MODE_OK;
+}
+
+static void inno_hdmi_starfive_enable(struct device *dev,
+				      struct drm_display_mode *mode)
+{
+	struct stf_inno_hdmi_controller *ctrl = dev_get_drvdata(dev);
+	int ret;
+
+	/*
+	 * 1. Set the pixel clock rate. This calls the PHY driver's .set_rate op.
+	 */
+	ret = clk_set_rate(ctrl->clks[CLK_PCLK].clk, mode->clock * 1000);
+	if (ret) {
+		dev_err(dev, "Failed to set pclk rate %d: %d\n",
+			mode->clock * 1000, ret);
+		return;
+	}
+
+	/*
+	 * 2. Enable the pixel clock. This calls the PHY driver's .prepare op.
+	 */
+	ret = clk_prepare_enable(ctrl->clks[CLK_PCLK].clk);
+	if (ret) {
+		dev_err(dev, "Failed to enable pclk: %d\n", ret);
+		return;
+	}
+
+	/*
+	 * 3. Power on the PHY. This calls the PHY driver's .power_on op,
+	 * which configures the Post-PLL and analog blocks.
+	 */
+	ret = phy_power_on(ctrl->phy);
+	if (ret) {
+		dev_err(dev, "Failed to power on PHY: %d\n", ret);
+		clk_disable_unprepare(ctrl->clks[CLK_PCLK].clk);
+		return;
+	}
+
+	ctrl->enabled = true;
+}
+
+static void inno_hdmi_starfive_disable(struct device *dev)
+{
+	struct stf_inno_hdmi_controller *ctrl = dev_get_drvdata(dev);
+
+	/*
+	 * .enable bails out early if the pixel clock rate is unsupported or
+	 * the PHY fails to power on, leaving pclk and the PHY untouched.
+	 * Only tear down what was actually brought up, otherwise the clock
+	 * refcount underflows.
+	 */
+	if (!ctrl->enabled)
+		return;
+
+	phy_power_off(ctrl->phy);
+	clk_disable_unprepare(ctrl->clks[CLK_PCLK].clk);
+	ctrl->enabled = false;
+}
+
+/*
+ * The DC8200 has two panels, each exposing a DP and a DPI interface, and a mux
+ * in dom_vout_syscon picks which of them drives the HDMI transmitter. Derive
+ * the mux setting from the port graph: the remote port number selects the
+ * DC8200 panel, and the remote endpoint number the interface on that panel
+ * (0 for DPI, 1 for DP). Both drive 8-bit RGB, the only format this driver
+ * currently produces.
+ */
+static int stf_inno_hdmi_setup_mux(struct device *dev)
+{
+	struct of_endpoint endpoint;
+	struct regmap *syscon;
+	u32 mask, val;
+	int ret;
+
+	syscon = syscon_regmap_lookup_by_phandle(dev->of_node,
+						 "starfive,vout-syscon");
+	if (IS_ERR(syscon))
+		return dev_err_probe(dev, PTR_ERR(syscon),
+				     "Failed to get vout syscon\n");
+
+	struct device_node *ep __free(device_node) =
+		of_graph_get_endpoint_by_regs(dev->of_node, 0, -1);
+	if (!ep)
+		return dev_err_probe(dev, -ENODEV, "No input endpoint\n");
+
+	struct device_node *remote __free(device_node) =
+		of_graph_get_remote_endpoint(ep);
+	if (!remote)
+		return dev_err_probe(dev, -ENODEV,
+				     "Input endpoint is not connected\n");
+
+	ret = of_graph_parse_endpoint(remote, &endpoint);
+	if (ret)
+		return dev_err_probe(dev, ret,
+				     "Failed to parse the remote endpoint\n");
+
+	if (endpoint.port > 1 || endpoint.id > 1)
+		return dev_err_probe(dev, -EINVAL,
+				     "Unsupported DC8200 output %u/%u\n",
+				     endpoint.port, endpoint.id);
+
+	/* Data mapping: 8-bit RGB on whichever interface is in use. */
+	mask = VOUT_HDMI_DPI_DP_SEL | VOUT_HDMI_DP_BIT_DEPTH |
+	       VOUT_HDMI_DP_YUV_MODE | VOUT_HDMI_DPI_BIT_DEPTH;
+	val = FIELD_PREP(VOUT_HDMI_DPI_DP_SEL, endpoint.id) |
+	      FIELD_PREP(VOUT_HDMI_DP_YUV_MODE, VOUT_HDMI_DP_YUV_MODE_RGB) |
+	      FIELD_PREP(VOUT_HDMI_DPI_BIT_DEPTH, VOUT_HDMI_DPI_BIT_DEPTH_8BIT);
+
+	ret = regmap_update_bits(syscon, VOUT_SYSCFG_4, mask, val);
+	if (ret)
+		return ret;
+
+	/* Which DC8200 panel drives the HDMI transmitter. */
+	return regmap_update_bits(syscon, VOUT_SYSCFG_8, VOUT_HDMI_PANEL_SEL,
+				  FIELD_PREP(VOUT_HDMI_PANEL_SEL,
+					     endpoint.port));
+}
+
+static void stf_inno_hdmi_clk_disable(void *data)
+{
+	struct stf_inno_hdmi_controller *ctrl = data;
+
+	clk_bulk_disable_unprepare(CLK_CTRL_NUM - 1, ctrl->clks);
+}
+
+static void stf_inno_hdmi_rst_assert(void *data)
+{
+	reset_control_assert(data);
+}
+
+static int starfive_inno_hdmi_controller_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct stf_inno_hdmi_controller *ctrl;
+	const struct inno_hdmi_plat_data *plat_data;
+	struct inno_hdmi *inno;
+	int ret;
+
+	ctrl = devm_kzalloc(dev, sizeof(*ctrl), GFP_KERNEL);
+	if (!ctrl)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, ctrl);
+
+	ctrl->phy = devm_phy_get(dev, NULL);
+	if (IS_ERR(ctrl->phy))
+		return dev_err_probe(dev, PTR_ERR(ctrl->phy), "Failed to get PHY\n");
+
+	ctrl->tx_rst = devm_reset_control_get_exclusive(dev, NULL);
+	if (IS_ERR(ctrl->tx_rst))
+		return dev_err_probe(dev, PTR_ERR(ctrl->tx_rst), "failed to get tx reset\n");
+
+	/* Populate the clock names this controller *consumes* */
+	ctrl->clks[CLK_SYS].id = "pclk";
+	ctrl->clks[CLK_M].id = "mclk";
+	ctrl->clks[CLK_B].id = "bclk";
+	ctrl->clks[CLK_PCLK].id = "pixel"; /* Generated by the PHY */
+
+	ret = devm_clk_bulk_get(dev, CLK_CTRL_NUM, ctrl->clks);
+	if (ret)
+		return dev_err_probe(dev, ret, "Unable to get controller clocks\n");
+
+	/*
+	 * Tear the clocks and the reset down through devm, so that they outlive
+	 * everything registered after them. The bridge is added with
+	 * devm_drm_bridge_add(), and unwinding in the wrong order would leave it
+	 * registered while its clocks are already gated.
+	 *
+	 * The pixel clock is enabled on demand during modeset.
+	 */
+	ret = clk_bulk_prepare_enable(CLK_CTRL_NUM - 1, ctrl->clks);
+	if (ret)
+		return ret;
+
+	ret = devm_add_action_or_reset(dev, stf_inno_hdmi_clk_disable, ctrl);
+	if (ret)
+		return ret;
+
+	ret = reset_control_deassert(ctrl->tx_rst);
+	if (ret)
+		return ret;
+
+	ret = devm_add_action_or_reset(dev, stf_inno_hdmi_rst_assert,
+				       ctrl->tx_rst);
+	if (ret)
+		return ret;
+
+	ret = stf_inno_hdmi_setup_mux(dev);
+	if (ret)
+		return ret;
+
+	plat_data = of_device_get_match_data(dev);
+
+	/* Hand off to the generic library to create the bridge. */
+	inno = inno_hdmi_probe(pdev, plat_data);
+	if (IS_ERR(inno))
+		return PTR_ERR(inno);
+
+	return 0;
+}
+
+static const struct inno_hdmi_plat_ops stf_inno_hdmi_plat_ops = {
+	.enable = inno_hdmi_starfive_enable,
+	.disable = inno_hdmi_starfive_disable,
+	.mode_valid = inno_hdmi_starfive_mode_valid,
+};
+
+static const struct inno_hdmi_plat_data stf_inno_hdmi_plat_data = {
+	.ops = &stf_inno_hdmi_plat_ops,
+	.reg_clk_source_tmds = true,
+};
+
+static const struct of_device_id starfive_hdmi_controller_dt_ids[] = {
+	{ .compatible = "starfive,jh7110-inno-hdmi-controller",
+	  .data = &stf_inno_hdmi_plat_data },
+	{}
+};
+MODULE_DEVICE_TABLE(of, starfive_hdmi_controller_dt_ids);
+
+static struct platform_driver starfive_inno_hdmi_controller_driver = {
+	.probe = starfive_inno_hdmi_controller_probe,
+	.driver = {
+		.name = "starfive-inno-hdmi-controller",
+		.of_match_table = starfive_hdmi_controller_dt_ids,
+	},
+};
+module_platform_driver(starfive_inno_hdmi_controller_driver);
+
+MODULE_AUTHOR("Michal Wilczynski <m.wilczynski@samsung.com>");
+MODULE_DESCRIPTION("StarFive INNO HDMI Controller Driver");
+MODULE_LICENSE("GPL");

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 17/18] riscv: dts: starfive: jh7110: Update DT for display subsystem

[Michal Wilczynski]

Activate the display subsystem by describing the video output subsystem,
which the documentation calls dom_vout_top, as a bus node covering the
whole 0x29400000 region, with dc8200, the HDMI block, the video output
system controller and voutcrg as its children.

The subsystem node owns the resources its children share: the NoC display
bus clock and reset that gate access to every register in the region, and
the PD_VOUT power domain. Modelling it this way keeps a shared gate owned
by the block that shares it, and lets dc8200 inherit dma-noncoherent for
framebuffer DMA from the bus it sits on.

The monolithic hdmi node is in turn modelled as a container with hdmi_phy
and hdmi_controller children, which share its register window: the PHY
takes only xin24m and provides the pixel clock and the phy, while the
controller takes its clocks from voutcrg.

voutcrg consumes the pixel clock from the &hdmi_phy node instead of the
old fixed-clock, and dc8200 gets its pixel clocks from voutcrg's MUXes.
The old, incorrect hdmitx0-pixel-clock fixed-clock node is removed.

The HDMI controller gets a phandle to the video output system controller,
which holds the mux selecting the DC8200 output that drives the HDMI
transmitter.

CMA is enlarged and constrained to memory the display controller can
address, because the default pool is too small for its framebuffers.

Co-developed-by: Dominique Belhachemi <db@domibel.de>
Signed-off-by: Dominique Belhachemi <db@domibel.de>
Tested-by: Icenowy Zheng <zhengxingda@iscas.ac.cn>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 arch/riscv/boot/dts/starfive/jh7110-common.dtsi | 121 +++++++++++++++++++++++-
 arch/riscv/boot/dts/starfive/jh7110.dtsi        | 105 ++++++++++++++++----
 2 files changed, 203 insertions(+), 23 deletions(-)

diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
index a7a1c09a2c9075711f3a214a49618911fdc7b421..a4c3daf712a63b177f744e8c613416d22e0c9dbd 100644
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -33,6 +33,27 @@ memory@40000000 {
 		bootph-pre-ram;
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * The display controller allocates its framebuffers from CMA,
+		 * and the default pool is too small for them. Keep the pool
+		 * inside the range the controller can address; it fits in the
+		 * memory every VisionFive 2 variant has.
+		 */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x0 0x20000000>;
+			alignment = <0x0 0x1000>;
+			alloc-ranges = <0x0 0x70000000 0x0 0x20000000>;
+			linux,cma-default;
+		};
+	};
+
 	gpio-restart {
 		compatible = "gpio-restart";
 		gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
@@ -73,12 +94,47 @@ codec {
 			};
 		};
 	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
 };
 
 &cpus {
 	timebase-frequency = <4000000>;
 };
 
+&dc8200 {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		dpu_port0: port@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dpu_out_dpi0: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&hdmi_in>;
+			};
+		};
+
+		dpu_port1: port@1 {
+			reg = <1>;
+		};
+	};
+};
+
 &dvp_clk {
 	clock-frequency = <74250000>;
 };
@@ -99,8 +155,31 @@ &gmac1_rmii_refin {
 	clock-frequency = <50000000>;
 };
 
-&hdmitx0_pixelclk {
-	clock-frequency = <297000000>;
+&hdmi_controller {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_pins>;
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			hdmi_in: endpoint {
+				remote-endpoint = <&dpu_out_dpi0>;
+			};
+		};
+
+		hdmi_out_port: port@1 {
+			reg = <1>;
+
+			hdmi_out_con: endpoint {
+				remote-endpoint = <&hdmi_con_in>;
+			};
+		};
+	};
 };
 
 &i2srx_bclk_ext {
@@ -351,6 +430,40 @@ &syscrg {
 };
 
 &sysgpio {
+	hdmi_pins: hdmi-0 {
+		hdmi-cec-pins {
+			pinmux = <GPIOMUX(14, GPOUT_SYS_HDMI_CEC_SDA,
+					      GPOEN_SYS_HDMI_CEC_SDA,
+					      GPI_SYS_HDMI_CEC_SDA)>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		hdmi-hpd-pins {
+			pinmux = <GPIOMUX(15, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_HDMI_HPD)>;
+			input-enable;
+			bias-disable; /* external pull-up */
+		};
+
+		hdmi-scl-pins {
+			pinmux = <GPIOMUX(0, GPOUT_SYS_HDMI_DDC_SCL,
+					     GPOEN_SYS_HDMI_DDC_SCL,
+					     GPI_SYS_HDMI_DDC_SCL)>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		hdmi-sda-pins {
+			pinmux = <GPIOMUX(1, GPOUT_SYS_HDMI_DDC_SDA,
+					     GPOEN_SYS_HDMI_DDC_SDA,
+					     GPI_SYS_HDMI_DDC_SDA)>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
+
 	i2c0_pins: i2c0-0 {
 		i2c-pins {
 			pinmux = <GPIOMUX(57, GPOUT_LOW,
@@ -629,3 +742,7 @@ &U74_3 {
 &U74_4 {
 	cpu-supply = <&vdd_cpu>;
 };
+
+&voutcrg {
+	status = "okay";
+};
diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
index 9c3e4598747eb5541effe697044484715569a285..bc2470963520eef30d7524370fcb013f0631f509 100644
--- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
@@ -290,12 +290,6 @@ gmac1_rmii_refin: gmac1-rmii-refin-clock {
 		#clock-cells = <0>;
 	};
 
-	hdmitx0_pixelclk: hdmitx0-pixel-clock {
-		compatible = "fixed-clock";
-		clock-output-names = "hdmitx0_pixelclk";
-		#clock-cells = <0>;
-	};
-
 	i2srx_bclk_ext: i2srx-bclk-ext-clock {
 		compatible = "fixed-clock";
 		clock-output-names = "i2srx_bclk_ext";
@@ -352,6 +346,13 @@ tdm_ext: tdm-ext-clock {
 		#clock-cells = <0>;
 	};
 
+	xin24m: xin24m-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "xin24m";
+	};
+
 	soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&plic>;
@@ -1199,22 +1200,84 @@ csi_phy: phy@19820000 {
 			#phy-cells = <0>;
 		};
 
-		voutcrg: clock-controller@295c0000 {
-			compatible = "starfive,jh7110-voutcrg";
-			reg = <0x0 0x295c0000 0x0 0x10000>;
-			clocks = <&syscrg JH7110_SYSCLK_VOUT_SRC>,
-				 <&syscrg JH7110_SYSCLK_VOUT_TOP_AHB>,
-				 <&syscrg JH7110_SYSCLK_VOUT_TOP_AXI>,
-				 <&syscrg JH7110_SYSCLK_VOUT_TOP_HDMITX0_MCLK>,
-				 <&syscrg JH7110_SYSCLK_I2STX0_BCLK>,
-				 <&hdmitx0_pixelclk>;
-			clock-names = "vout_src", "vout_top_ahb",
-				      "vout_top_axi", "vout_top_hdmitx0_mclk",
-				      "i2stx0_bclk", "hdmitx0_pixelclk";
-			resets = <&syscrg JH7110_SYSRST_VOUT_TOP_SRC>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
+		vout_subsystem: display-subsystem@29400000 {
+			compatible = "starfive,jh7110-vout-subsystem";
+			reg = <0x0 0x29400000 0x0 0x200000>;
+			ranges;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			clocks = <&syscrg JH7110_SYSCLK_NOC_BUS_DISP_AXI>;
+			dma-noncoherent;
 			power-domains = <&pwrc JH7110_PD_VOUT>;
+			resets = <&syscrg JH7110_SYSRST_NOC_BUS_DISP_AXI>;
+
+			dc8200: display@29400000 {
+				compatible = "starfive,jh7110-dc8200", "verisilicon,dc";
+				reg = <0x0 0x29400000 0x0 0x2800>;
+				clocks = <&voutcrg JH7110_VOUTCLK_DC8200_CORE>,
+					 <&voutcrg JH7110_VOUTCLK_DC8200_AXI>,
+					 <&voutcrg JH7110_VOUTCLK_DC8200_AHB>,
+					 <&voutcrg JH7110_VOUTCLK_DC8200_PIX0>,
+					 <&voutcrg JH7110_VOUTCLK_DC8200_PIX1>;
+				clock-names = "core", "axi", "ahb", "pix0", "pix1";
+				assigned-clocks = <&voutcrg JH7110_VOUTCLK_DC8200_PIX0>,
+						  <&voutcrg JH7110_VOUTCLK_DC8200_PIX1>;
+				assigned-clock-parents = <&hdmi_phy>, <&hdmi_phy>;
+				interrupts = <95>;
+				resets = <&voutcrg JH7110_VOUTRST_DC8200_CORE>,
+					 <&voutcrg JH7110_VOUTRST_DC8200_AXI>,
+					 <&voutcrg JH7110_VOUTRST_DC8200_AHB>;
+				reset-names = "core", "axi", "ahb";
+			};
+
+			hdmi_subsystem: hdmi@29590000 {
+				compatible = "starfive,jh7110-hdmi-subsystem";
+				reg = <0x0 0x29590000 0x0 0x4000>;
+
+				hdmi_controller: controller {
+					compatible =
+						"starfive,jh7110-inno-hdmi-controller";
+					clocks = <&voutcrg JH7110_VOUTCLK_HDMI_TX_SYS>,
+						 <&voutcrg JH7110_VOUTCLK_HDMI_TX_MCLK>,
+						 <&voutcrg JH7110_VOUTCLK_HDMI_TX_BCLK>,
+						 <&hdmi_phy>;
+					clock-names = "pclk", "mclk", "bclk", "pixel";
+					interrupts = <99>;
+					phys = <&hdmi_phy>;
+					resets = <&voutcrg JH7110_VOUTRST_HDMI_TX_HDMI>;
+					starfive,vout-syscon = <&vout_syscon>;
+				};
+
+				hdmi_phy: phy {
+					compatible = "starfive,jh7110-inno-hdmi-phy";
+					clocks = <&xin24m>;
+					#clock-cells = <0>;
+					#phy-cells = <0>;
+				};
+			};
+
+			vout_syscon: syscon@295b0000 {
+				compatible = "starfive,jh7110-vout-syscon", "syscon";
+				reg = <0x0 0x295b0000 0x0 0x10000>;
+			};
+
+			voutcrg: clock-controller@295c0000 {
+				compatible = "starfive,jh7110-voutcrg";
+				reg = <0x0 0x295c0000 0x0 0x10000>;
+				clocks = <&syscrg JH7110_SYSCLK_VOUT_SRC>,
+					 <&syscrg JH7110_SYSCLK_VOUT_TOP_AHB>,
+					 <&syscrg JH7110_SYSCLK_VOUT_TOP_AXI>,
+					 <&syscrg JH7110_SYSCLK_VOUT_TOP_HDMITX0_MCLK>,
+					 <&syscrg JH7110_SYSCLK_I2STX0_BCLK>,
+					 <&hdmi_phy>;
+				clock-names = "vout_src", "vout_top_ahb",
+					      "vout_top_axi", "vout_top_hdmitx0_mclk",
+					      "i2stx0_bclk", "hdmitx0_pixelclk";
+				power-domains = <&pwrc JH7110_PD_VOUT>;
+				resets = <&syscrg JH7110_SYSRST_VOUT_TOP_SRC>;
+				#clock-cells = <1>;
+				#reset-cells = <1>;
+			};
 		};
 
 		pcie0: pcie@940000000 {

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

[PATCH v6 18/18] MAINTAINERS: Add StarFive JH7110 display subsystem entry

[Michal Wilczynski]

The JH7110 display subsystem spans a PHY driver, a DRM bridge driver,
a parent device and their bindings, and has no existing maintainer entry.

Add an entry covering them so patches reach someone who can review them.

Reviewed-by: Joshua Peisach <jpeisach@ubuntu.com>
Tested-by: Byron Stanoszek <gandalf@winds.org>
Tested-by: OOHehir <oo.hehir@gmail.com>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
---
 MAINTAINERS | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 782389bd5cd3d9e0117ebdfae707e1f61cb3e772..c26ac0bc60e5a9b777b0cb07ff0109e5a7cd1ae4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -26093,6 +26093,17 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml
 F:	drivers/net/ethernet/stmicro/stmmac/dwmac-starfive.c
 
+STARFIVE JH7110 DISPLAY SUBSYSTEM
+M:	Michal Wilczynski <m.wilczynski@samsung.com>
+R:	Icenowy Zheng <zhengxingda@iscas.ac.cn>
+S:	Maintained
+F:	Documentation/devicetree/bindings/display/bridge/starfive,jh7110-inno-hdmi-controller.yaml
+F:	Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-hdmi-subsystem.yaml
+F:	Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-vout-subsystem.yaml
+F:	drivers/gpu/drm/bridge/jh7110-inno-hdmi.c
+F:	drivers/soc/starfive/jh7110-hdmi-subsystem.c
+F:	drivers/soc/starfive/jh7110-vout-subsystem.c
+
 STARFIVE JH7110 DPHY RX DRIVER
 M:	Jack Zhu <jack.zhu@starfivetech.com>
 M:	Changhuang Liang <changhuang.liang@starfivetech.com>

-- 
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv