[PATCH] arm64: dts: rockchip: Correct GPIO polarity on brcm BT nodes

[PATCH] arm64: dts: rockchip: Correct GPIO polarity on brcm BT nodes

[Diederik de Haas]

The GPIO polarity of the 'shutdown-gpios' property needs to be
ACTIVE_HIGH or the Bluetooth device won't work.
This also matches what other devices with the same BT device have.

When changing from 'reset-gpios' to 'shutdown-gpios', I forgot to also
correct the GPIO polarity, so do that now.

Fixes: a3a625086192 ("arm64: dts: rockchip: Fix reset-gpios property on brcm BT nodes")
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
---
 arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi  | 2 +-
 arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi
index a477bd992b40..0131f2cdd312 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi
@@ -688,7 +688,7 @@ bluetooth {
 		host-wakeup-gpios = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
 		pinctrl-0 = <&bt_enable_h>, <&bt_host_wake_l>, <&bt_wake_h>;
 		pinctrl-names = "default";
-		shutdown-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>;
+		shutdown-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
 		vbat-supply = <&vcc_wl>;
 		vddio-supply = <&vcca_1v8_pmu>;
 	};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3.dtsi
index e9fa9bee995a..1e36f73840da 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3566-radxa-cm3.dtsi
@@ -404,7 +404,7 @@ bluetooth {
 		host-wakeup-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&bt_host_wake_h &bt_reg_on_h &bt_wake_host_h>;
-		shutdown-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_LOW>;
+		shutdown-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
 		vbat-supply = <&vcc_3v3>;
 		vddio-supply = <&vcc_1v8>;
 	};
-- 
2.45.2


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH] arm64: dts: rockchip: Correct GPIO polarity on brcm BT nodes

[Krzysztof Kozlowski]

On 18/10/2024 11:22, Diederik de Haas wrote:
> The GPIO polarity of the 'shutdown-gpios' property needs to be
> ACTIVE_HIGH or the Bluetooth device won't work.
> This also matches what other devices with the same BT device have.

This should match the hardware. What if the Linux driver is just buggy?

Best regards,
Krzysztof


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH] arm64: dts: rockchip: Correct GPIO polarity on brcm BT nodes

[Diederik de Haas]

[-- Attachment #1.1: Type: text/plain, Size: 2009 bytes --]

On Fri Oct 18, 2024 at 12:11 PM CEST, Krzysztof Kozlowski wrote:
> On 18/10/2024 11:22, Diederik de Haas wrote:
> > The GPIO polarity of the 'shutdown-gpios' property needs to be
> > ACTIVE_HIGH or the Bluetooth device won't work.
> > This also matches what other devices with the same BT device have.
>
> This should match the hardware.

Fair point.

The only documentation I have for the AzureWave-CM256SM is a datasheet.

Para "3.4 Power up Timing Sequence" of that datasheet has the following:

"The AW-CM256SM has two signals that enable or disable the Bluetooth
and WLAN circuits and the internal regulator blocks, allowing the host
to control power consumption."

WL_REG_ON:
"When this pin is high, the regulators are enabled and the WLAN section
is out of reset. When this pin is low, the WLAN section is in reset. If
BT_REG_ON and WL_REG_ON are both low, the regulators are disabled."

BT_REG_ON:
"If both BT_REG_ON and WL_REG_ON are low, the regulators will be
disabled. When this pin is low and WL_REG_ON is high, the BT section
is in reset."

From that I conclude that BT_REG_ON needs to be high to get BT in a
working state.

But that datasheet is in its 19th revision, so can I assume that it now
is correct? (genuine question)

That's why I also looked at devices which uses the same hardware:
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/tree/WHENCE?h=20241017#n2973
and those all had ACTIVE_HIGH for 'shutdown-gpios' in their hardware
description (ie DeviceTree) and if they were all broken, I think we
would've heard about it.

And my own testing showed it not working with ACTIVE_LOW and working
with ACTIVE_HIGH.
I just messed up my previous patch submission process, which this patch
is meant to correct.

> What if the Linux driver is just buggy?

Given the amount of 'spam' I get in `bluetoothctl` when it is working, I
think there's a real possibility that that is (also) the case.

Cheers,
  Diederik

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 170 bytes --]

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip