[PATCH AUTOSEL 6.14 035/642] spi-rockchip: Fix register out of bounds access

[PATCH AUTOSEL 6.14 035/642] spi-rockchip: Fix register out of bounds access

[Sasha Levin]

From: Luis de Arquer <luis.dearquer@inertim.com>

[ Upstream commit 7a874e8b54ea21094f7fd2d428b164394c6cb316 ]

Do not write native chip select stuff for GPIO chip selects.
GPIOs can be numbered much higher than native CS.
Also, it makes no sense.

Signed-off-by: Luis de Arquer <luis.dearquer@inertim.com>
Link: https://patch.msgid.link/365ccddfba110549202b3520f4401a6a936e82a8.camel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/spi/spi-rockchip.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/spi/spi-rockchip.c b/drivers/spi/spi-rockchip.c
index 1bc012fce7cb8..1a6381de6f33d 100644
--- a/drivers/spi/spi-rockchip.c
+++ b/drivers/spi/spi-rockchip.c
@@ -547,7 +547,7 @@ static int rockchip_spi_config(struct rockchip_spi *rs,
 	cr0 |= (spi->mode & 0x3U) << CR0_SCPH_OFFSET;
 	if (spi->mode & SPI_LSB_FIRST)
 		cr0 |= CR0_FBM_LSB << CR0_FBM_OFFSET;
-	if (spi->mode & SPI_CS_HIGH)
+	if ((spi->mode & SPI_CS_HIGH) && !(spi_get_csgpiod(spi, 0)))
 		cr0 |= BIT(spi_get_chipselect(spi, 0)) << CR0_SOI_OFFSET;
 
 	if (xfer->rx_buf && xfer->tx_buf)
-- 
2.39.5


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH AUTOSEL 6.14 171/642] phy: rockchip: usbdp: Only verify link rates/lanes/voltage when the corresponding set flags are set

[Sasha Levin]

From: Andy Yan <andy.yan@rock-chips.com>

[ Upstream commit 969a38be437b68dc9e12e3c3f08911c9f9c8be73 ]

According documentation of phy_configure_opts_dp, at the configure
stage, link rates should only be verify/configure when set_rate
flag is set, the same applies to lanes and voltage.

So do it as the documentation says.
Because voltage setting depends on the lanes, link rates set
previously, so record the link rates and lanes at it's verify stage.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250312080041.524546-1-andyshrk@163.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/phy/rockchip/phy-rockchip-usbdp.c | 87 ++++++++++++++---------
 1 file changed, 53 insertions(+), 34 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index c04cf64f8a35d..fff04e0fbd800 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -187,6 +187,8 @@ struct rk_udphy {
 	u32 dp_aux_din_sel;
 	bool dp_sink_hpd_sel;
 	bool dp_sink_hpd_cfg;
+	unsigned int link_rate;
+	unsigned int lanes;
 	u8 bw;
 	int id;
 
@@ -1102,15 +1104,19 @@ static int rk_udphy_dp_phy_power_off(struct phy *phy)
 	return 0;
 }
 
-static int rk_udphy_dp_phy_verify_link_rate(unsigned int link_rate)
+/*
+ * Verify link rate
+ */
+static int rk_udphy_dp_phy_verify_link_rate(struct rk_udphy *udphy,
+					    struct phy_configure_opts_dp *dp)
 {
-	switch (link_rate) {
+	switch (dp->link_rate) {
 	case 1620:
 	case 2700:
 	case 5400:
 	case 8100:
+		udphy->link_rate = dp->link_rate;
 		break;
-
 	default:
 		return -EINVAL;
 	}
@@ -1118,45 +1124,44 @@ static int rk_udphy_dp_phy_verify_link_rate(unsigned int link_rate)
 	return 0;
 }
 
-static int rk_udphy_dp_phy_verify_config(struct rk_udphy *udphy,
-					 struct phy_configure_opts_dp *dp)
+static int rk_udphy_dp_phy_verify_lanes(struct rk_udphy *udphy,
+					struct phy_configure_opts_dp *dp)
 {
-	int i, ret;
-
-	/* If changing link rate was required, verify it's supported. */
-	ret = rk_udphy_dp_phy_verify_link_rate(dp->link_rate);
-	if (ret)
-		return ret;
-
-	/* Verify lane count. */
 	switch (dp->lanes) {
 	case 1:
 	case 2:
 	case 4:
 		/* valid lane count. */
+		udphy->lanes = dp->lanes;
 		break;
 
 	default:
 		return -EINVAL;
 	}
 
-	/*
-	 * If changing voltages is required, check swing and pre-emphasis
-	 * levels, per-lane.
-	 */
-	if (dp->set_voltages) {
-		/* Lane count verified previously. */
-		for (i = 0; i < dp->lanes; i++) {
-			if (dp->voltage[i] > 3 || dp->pre[i] > 3)
-				return -EINVAL;
+	return 0;
+}
 
-			/*
-			 * Sum of voltage swing and pre-emphasis levels cannot
-			 * exceed 3.
-			 */
-			if (dp->voltage[i] + dp->pre[i] > 3)
-				return -EINVAL;
-		}
+/*
+ * If changing voltages is required, check swing and pre-emphasis
+ * levels, per-lane.
+ */
+static int rk_udphy_dp_phy_verify_voltages(struct rk_udphy *udphy,
+					   struct phy_configure_opts_dp *dp)
+{
+	int i;
+
+	/* Lane count verified previously. */
+	for (i = 0; i < udphy->lanes; i++) {
+		if (dp->voltage[i] > 3 || dp->pre[i] > 3)
+			return -EINVAL;
+
+		/*
+		 * Sum of voltage swing and pre-emphasis levels cannot
+		 * exceed 3.
+		 */
+		if (dp->voltage[i] + dp->pre[i] > 3)
+			return -EINVAL;
 	}
 
 	return 0;
@@ -1196,9 +1201,23 @@ static int rk_udphy_dp_phy_configure(struct phy *phy,
 	u32 i, val, lane;
 	int ret;
 
-	ret = rk_udphy_dp_phy_verify_config(udphy, dp);
-	if (ret)
-		return ret;
+	if (dp->set_rate) {
+		ret = rk_udphy_dp_phy_verify_link_rate(udphy, dp);
+		if (ret)
+			return ret;
+	}
+
+	if (dp->set_lanes) {
+		ret = rk_udphy_dp_phy_verify_lanes(udphy, dp);
+		if (ret)
+			return ret;
+	}
+
+	if (dp->set_voltages) {
+		ret = rk_udphy_dp_phy_verify_voltages(udphy, dp);
+		if (ret)
+			return ret;
+	}
 
 	if (dp->set_rate) {
 		regmap_update_bits(udphy->pma_regmap, CMN_DP_RSTN_OFFSET,
@@ -1243,9 +1262,9 @@ static int rk_udphy_dp_phy_configure(struct phy *phy,
 	}
 
 	if (dp->set_voltages) {
-		for (i = 0; i < dp->lanes; i++) {
+		for (i = 0; i < udphy->lanes; i++) {
 			lane = udphy->dp_lane_sel[i];
-			switch (dp->link_rate) {
+			switch (udphy->link_rate) {
 			case 1620:
 			case 2700:
 				regmap_update_bits(udphy->pma_regmap,
-- 
2.39.5


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH AUTOSEL 6.14 275/642] drm/rockchip: vop2: Add uv swap for cluster window

[Sasha Levin]

From: Andy Yan <andy.yan@rock-chips.com>

[ Upstream commit e7aae9f6d762139f8d2b86db03793ae0ab3dd802 ]

The Cluster windows of upcoming VOP on rk3576 also support
linear YUV support, we need to set uv swap bit for it.

As the VOP2_WIN_UV_SWA register defined on rk3568/rk3588 is
0xffffffff, so this register will not be touched on these
two platforms.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net> # on RK3568
Tested-by: Detlev Casanova <detlev.casanova@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250303034436.192400-4-andyshrk@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c
index 17a98845fd31b..64029237358d8 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c
@@ -1547,10 +1547,8 @@ static void vop2_plane_atomic_update(struct drm_plane *plane,
 
 	rb_swap = vop2_win_rb_swap(fb->format->format);
 	vop2_win_write(win, VOP2_WIN_RB_SWAP, rb_swap);
-	if (!vop2_cluster_window(win)) {
-		uv_swap = vop2_win_uv_swap(fb->format->format);
-		vop2_win_write(win, VOP2_WIN_UV_SWAP, uv_swap);
-	}
+	uv_swap = vop2_win_uv_swap(fb->format->format);
+	vop2_win_write(win, VOP2_WIN_UV_SWAP, uv_swap);
 
 	if (fb->format->is_yuv) {
 		vop2_win_write(win, VOP2_WIN_UV_VIR, DIV_ROUND_UP(fb->pitches[1], 4));
-- 
2.39.5


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH AUTOSEL 6.14 450/642] phy: phy-rockchip-samsung-hdptx: Swap the definitions of LCPLL_REF and ROPLL_REF

[Sasha Levin]

From: Damon Ding <damon.ding@rock-chips.com>

[ Upstream commit 2947c8065e9efdd3b6434d2817dc8896234a3fc0 ]

According to the datasheet, setting the dig_clk_sel bit of CMN_REG(0097)
to 1'b1 selects LCPLL as the reference clock, while setting it to 1'b0
selects the ROPLL.

Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20250205105157.580060-2-damon.ding@rock-chips.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
index 2fb4f297fda3d..920abf6fa9bdd 100644
--- a/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
+++ b/drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c
@@ -94,8 +94,8 @@
 #define LCPLL_ALONE_MODE		BIT(1)
 /* CMN_REG(0097) */
 #define DIG_CLK_SEL			BIT(1)
-#define ROPLL_REF			BIT(1)
-#define LCPLL_REF			0
+#define LCPLL_REF			BIT(1)
+#define ROPLL_REF			0
 /* CMN_REG(0099) */
 #define CMN_ROPLL_ALONE_MODE		BIT(2)
 #define ROPLL_ALONE_MODE		BIT(2)
-- 
2.39.5


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH AUTOSEL 6.14 542/642] drm/rockchip: vop2: Improve display modes handling on RK3588 HDMI0

[Sasha Levin]

From: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>

[ Upstream commit 2c1268e7aad0819f38e56134bbc2095fd95fde1b ]

The RK3588 specific implementation is currently quite limited in terms
of handling the full range of display modes supported by the connected
screens, e.g. 2560x1440@75Hz, 2048x1152@60Hz, 1024x768@60Hz are just a
few of them.

Additionally, it doesn't cope well with non-integer refresh rates like
59.94, 29.97, 23.98, etc.

Make use of HDMI0 PHY PLL as a more accurate DCLK source to handle
all display modes up to 4K@60Hz.

Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204-vop2-hdmi0-disp-modes-v3-3-d71c6a196e58@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/rockchip/rockchip_drm_vop2.c | 34 ++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c
index 64029237358d8..bcbd498823928 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop2.c
@@ -159,6 +159,7 @@ struct vop2_video_port {
 	struct drm_crtc crtc;
 	struct vop2 *vop2;
 	struct clk *dclk;
+	struct clk *dclk_src;
 	unsigned int id;
 	const struct vop2_video_port_data *data;
 
@@ -214,6 +215,7 @@ struct vop2 {
 	struct clk *hclk;
 	struct clk *aclk;
 	struct clk *pclk;
+	struct clk *pll_hdmiphy0;
 
 	/* optional internal rgb encoder */
 	struct rockchip_rgb *rgb;
@@ -222,6 +224,8 @@ struct vop2 {
 	struct vop2_win win[];
 };
 
+#define VOP2_MAX_DCLK_RATE		600000000
+
 #define vop2_output_if_is_hdmi(x)	((x) == ROCKCHIP_VOP2_EP_HDMI0 || \
 					 (x) == ROCKCHIP_VOP2_EP_HDMI1)
 
@@ -1155,6 +1159,9 @@ static void vop2_crtc_atomic_disable(struct drm_crtc *crtc,
 
 	vop2_crtc_disable_irq(vp, VP_INT_DSP_HOLD_VALID);
 
+	if (vp->dclk_src)
+		clk_set_parent(vp->dclk, vp->dclk_src);
+
 	clk_disable_unprepare(vp->dclk);
 
 	vop2->enable_count--;
@@ -2257,6 +2264,27 @@ static void vop2_crtc_atomic_enable(struct drm_crtc *crtc,
 
 	vop2_vp_write(vp, RK3568_VP_MIPI_CTRL, 0);
 
+	/*
+	 * Switch to HDMI PHY PLL as DCLK source for display modes up
+	 * to 4K@60Hz, if available, otherwise keep using the system CRU.
+	 */
+	if (vop2->pll_hdmiphy0 && clock <= VOP2_MAX_DCLK_RATE) {
+		drm_for_each_encoder_mask(encoder, crtc->dev, crtc_state->encoder_mask) {
+			struct rockchip_encoder *rkencoder = to_rockchip_encoder(encoder);
+
+			if (rkencoder->crtc_endpoint_id == ROCKCHIP_VOP2_EP_HDMI0) {
+				if (!vp->dclk_src)
+					vp->dclk_src = clk_get_parent(vp->dclk);
+
+				ret = clk_set_parent(vp->dclk, vop2->pll_hdmiphy0);
+				if (ret < 0)
+					drm_warn(vop2->drm,
+						 "Could not switch to HDMI0 PHY PLL: %d\n", ret);
+				break;
+			}
+		}
+	}
+
 	clk_set_rate(vp->dclk, clock);
 
 	vop2_post_config(crtc);
@@ -3697,6 +3725,12 @@ static int vop2_bind(struct device *dev, struct device *master, void *data)
 		return PTR_ERR(vop2->pclk);
 	}
 
+	vop2->pll_hdmiphy0 = devm_clk_get_optional(vop2->dev, "pll_hdmiphy0");
+	if (IS_ERR(vop2->pll_hdmiphy0)) {
+		drm_err(vop2->drm, "failed to get pll_hdmiphy0\n");
+		return PTR_ERR(vop2->pll_hdmiphy0);
+	}
+
 	vop2->irq = platform_get_irq(pdev, 0);
 	if (vop2->irq < 0) {
 		drm_err(vop2->drm, "cannot find irq for vop2\n");
-- 
2.39.5


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip