From: Chris Morgan <macroalpha82@gmail.com>
To: linux-iio@vger.kernel.org
Cc: andy@kernel.org, nuno.sa@analog.com, dlechner@baylibre.com,
jic23@kernel.org, jean-baptiste.maneyrol@tdk.com,
linux-rockchip@lists.infradead.org, devicetree@vger.kernel.org,
heiko@sntech.de, conor+dt@kernel.org, krzk+dt@kernel.org,
robh@kernel.org, andriy.shevchenko@intel.com,
Chris Morgan <macromorgan@hotmail.com>
Subject: [PATCH V5 05/11] iio: imu: inv_icm42607: Add PM support for icm42607
Date: Sat, 9 May 2026 14:18:59 -0500 [thread overview]
Message-ID: <20260509191907.24734-6-macroalpha82@gmail.com> (raw)
In-Reply-To: <20260509191907.24734-1-macroalpha82@gmail.com>
From: Chris Morgan <macromorgan@hotmail.com>
Add power management support for the ICM42607 device driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
drivers/iio/imu/inv_icm42607/inv_icm42607.h | 10 ++
.../iio/imu/inv_icm42607/inv_icm42607_core.c | 148 +++++++++++++++++-
.../iio/imu/inv_icm42607/inv_icm42607_i2c.c | 1 +
.../iio/imu/inv_icm42607/inv_icm42607_spi.c | 1 +
4 files changed, 159 insertions(+), 1 deletion(-)
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607.h b/drivers/iio/imu/inv_icm42607/inv_icm42607.h
index 3ebc06025051..623ff3936b4b 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607.h
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607.h
@@ -10,6 +10,7 @@
#include <linux/bitops.h>
#include <linux/iio/iio.h>
#include <linux/mutex.h>
+#include <linux/pm.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
@@ -96,6 +97,12 @@ struct inv_icm42607_hw {
const struct inv_icm42607_conf *conf;
};
+struct inv_icm42607_suspended {
+ enum inv_icm42607_sensor_mode gyro;
+ enum inv_icm42607_sensor_mode accel;
+ bool temp;
+};
+
/**
* struct inv_icm42607_state - driver state variables
* @lock: lock for serializing multiple registers access.
@@ -105,6 +112,7 @@ struct inv_icm42607_hw {
* @irq: chip irq, required to enable/disable and set wakeup
* @orientation: sensor chip orientation relative to main hardware.
* @conf: chip sensors configurations.
+ * @suspended: suspended sensors configuration.
*/
struct inv_icm42607_state {
struct mutex lock;
@@ -114,6 +122,7 @@ struct inv_icm42607_state {
int irq;
struct iio_mount_matrix orientation;
struct inv_icm42607_conf conf;
+ struct inv_icm42607_suspended suspended;
};
/* Virtual register addresses: @bank on MSB (4 upper bits), @address on LSB */
@@ -337,6 +346,7 @@ typedef int (*inv_icm42607_bus_setup)(struct inv_icm42607_state *);
extern const struct regmap_config inv_icm42607_regmap_config;
extern const struct inv_icm42607_hw inv_icm42607_hw_data;
extern const struct inv_icm42607_hw inv_icm42607p_hw_data;
+extern const struct dev_pm_ops inv_icm42607_pm_ops;
int inv_icm42607_core_probe(struct regmap *regmap, const struct inv_icm42607_hw *hw,
inv_icm42607_bus_setup bus_setup);
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
index 8ff51711ab1f..047de1b40550 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_core.c
@@ -9,6 +9,7 @@
#include <linux/irq.h>
#include <linux/module.h>
#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
#include <linux/property.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
@@ -66,6 +67,62 @@ const struct inv_icm42607_hw inv_icm42607p_hw_data = {
};
EXPORT_SYMBOL_NS_GPL(inv_icm42607p_hw_data, "IIO_ICM42607");
+static int inv_icm42607_set_pwr_mgmt0(struct inv_icm42607_state *st,
+ enum inv_icm42607_sensor_mode gyro,
+ enum inv_icm42607_sensor_mode accel,
+ bool temp, unsigned int *sleep_ms)
+{
+ enum inv_icm42607_sensor_mode oldgyro = st->conf.gyro.mode;
+ enum inv_icm42607_sensor_mode oldaccel = st->conf.accel.mode;
+ bool oldtemp = st->conf.temp_en;
+ unsigned int sleepval;
+ unsigned int val;
+ int ret;
+
+ if (gyro == oldgyro && accel == oldaccel && temp == oldtemp)
+ return 0;
+
+ val = FIELD_PREP(INV_ICM42607_PWR_MGMT0_GYRO_MODE_MASK, gyro);
+ val |= FIELD_PREP(INV_ICM42607_PWR_MGMT0_ACCEL_MODE_MASK, accel);
+ if (!temp)
+ val |= INV_ICM42607_PWR_MGMT0_ACCEL_LP_CLK_SEL;
+ ret = regmap_write(st->map, INV_ICM42607_REG_PWR_MGMT0, val);
+ if (ret)
+ return ret;
+
+ st->conf.gyro.mode = gyro;
+ st->conf.accel.mode = accel;
+ st->conf.temp_en = temp;
+
+ sleepval = 0;
+ if (temp && !oldtemp) {
+ if (sleepval < INV_ICM42607_TEMP_STARTUP_TIME_MS)
+ sleepval = INV_ICM42607_TEMP_STARTUP_TIME_MS;
+ }
+ if (accel != oldaccel && oldaccel == INV_ICM42607_SENSOR_MODE_OFF) {
+ usleep_range(200, 300);
+ if (sleepval < INV_ICM42607_ACCEL_STARTUP_TIME_MS)
+ sleepval = INV_ICM42607_ACCEL_STARTUP_TIME_MS;
+ }
+ if (gyro != oldgyro) {
+ if (oldgyro == INV_ICM42607_SENSOR_MODE_OFF) {
+ usleep_range(200, 300);
+ if (sleepval < INV_ICM42607_GYRO_STARTUP_TIME_MS)
+ sleepval = INV_ICM42607_GYRO_STARTUP_TIME_MS;
+ } else if (gyro == INV_ICM42607_SENSOR_MODE_OFF) {
+ if (sleepval < INV_ICM42607_GYRO_STOP_TIME_MS)
+ sleepval = INV_ICM42607_GYRO_STOP_TIME_MS;
+ }
+ }
+
+ if (sleep_ms)
+ *sleep_ms = sleepval;
+ else if (sleepval)
+ msleep(sleepval);
+
+ return 0;
+}
+
static int inv_icm42607_set_conf(struct inv_icm42607_state *st,
const struct inv_icm42607_conf *conf)
{
@@ -192,8 +249,10 @@ static int inv_icm42607_enable_vddio_reg(struct inv_icm42607_state *st)
static void inv_icm42607_disable_vddio_reg(void *_data)
{
struct inv_icm42607_state *st = _data;
+ struct device *dev = regmap_get_device(st->map);
- regulator_disable(st->vddio_supply);
+ if (!pm_runtime_suspended(dev))
+ regulator_disable(st->vddio_supply);
}
int inv_icm42607_core_probe(struct regmap *regmap, const struct inv_icm42607_hw *hw,
@@ -251,10 +310,97 @@ int inv_icm42607_core_probe(struct regmap *regmap, const struct inv_icm42607_hw
if (ret)
return ret;
+ ret = devm_pm_runtime_set_active_enabled(dev);
+ if (ret)
+ return ret;
+
+ pm_runtime_set_autosuspend_delay(dev, INV_ICM42607_SUSPEND_DELAY_MS);
+ pm_runtime_use_autosuspend(dev);
+
return 0;
}
EXPORT_SYMBOL_NS_GPL(inv_icm42607_core_probe, "IIO_ICM42607");
+/*
+ * Suspend saves sensors state and turns everything off.
+ * Check first if runtime suspend has not already done the job.
+ */
+static int inv_icm42607_suspend(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+ int ret;
+
+ guard(mutex)(&st->lock);
+
+ if (pm_runtime_suspended(dev))
+ return 0;
+
+ ret = inv_icm42607_set_pwr_mgmt0(st, INV_ICM42607_SENSOR_MODE_OFF,
+ INV_ICM42607_SENSOR_MODE_OFF,
+ false, NULL);
+ if (ret)
+ return ret;
+ regulator_disable(st->vddio_supply);
+
+ return 0;
+}
+
+/*
+ * System resume gets the system back on and restores the sensors state.
+ * Manually put runtime power management in system active state.
+ */
+static int inv_icm42607_resume(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+ int ret;
+
+ guard(mutex)(&st->lock);
+
+ if (pm_runtime_suspended(dev))
+ return 0;
+
+ ret = inv_icm42607_enable_vddio_reg(st);
+ if (ret)
+ return ret;
+
+ /* Nothing else to restore at this time. */
+
+ return 0;
+}
+
+static int inv_icm42607_runtime_suspend(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+ int ret = 0;
+
+ guard(mutex)(&st->lock);
+
+ ret = inv_icm42607_set_pwr_mgmt0(st, INV_ICM42607_SENSOR_MODE_OFF,
+ INV_ICM42607_SENSOR_MODE_OFF, false,
+ NULL);
+ if (ret)
+ return ret;
+
+ regulator_disable(st->vddio_supply);
+
+ return 0;
+}
+
+static int inv_icm42607_runtime_resume(struct device *dev)
+{
+ struct inv_icm42607_state *st = dev_get_drvdata(dev);
+
+ guard(mutex)(&st->lock);
+
+ return inv_icm42607_enable_vddio_reg(st);
+}
+
+EXPORT_NS_GPL_DEV_PM_OPS(inv_icm42607_pm_ops, IIO_ICM42607) = {
+ SYSTEM_SLEEP_PM_OPS(inv_icm42607_suspend, inv_icm42607_resume)
+ RUNTIME_PM_OPS(inv_icm42607_runtime_suspend,
+ inv_icm42607_runtime_resume, NULL)
+};
+
MODULE_AUTHOR("InvenSense, Inc.");
MODULE_DESCRIPTION("InvenSense ICM-42607x device driver");
MODULE_LICENSE("GPL");
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c
index 3859517f88c9..d4fab3d12753 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_i2c.c
@@ -72,6 +72,7 @@ static struct i2c_driver inv_icm42607_driver = {
.driver = {
.name = "inv-icm42607-i2c",
.of_match_table = inv_icm42607_of_matches,
+ .pm = pm_ptr(&inv_icm42607_pm_ops),
},
.id_table = inv_icm42607_id,
.probe = inv_icm42607_probe,
diff --git a/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c b/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c
index 4a38a11f2bae..23204194eca5 100644
--- a/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c
+++ b/drivers/iio/imu/inv_icm42607/inv_icm42607_spi.c
@@ -79,6 +79,7 @@ static struct spi_driver inv_icm42607_driver = {
.driver = {
.name = "inv-icm42607-spi",
.of_match_table = inv_icm42607_of_matches,
+ .pm = pm_ptr(&inv_icm42607_pm_ops),
},
.id_table = inv_icm42607_spi_id_table,
.probe = inv_icm42607_probe,
--
2.43.0
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
next prev parent reply other threads:[~2026-05-09 19:21 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-09 19:18 [PATCH V5 00/11] Add Invensense ICM42607 Chris Morgan
2026-05-09 19:18 ` [PATCH V5 01/11] dt-bindings: iio: imu: icm42600: Add mount-matrix to icm42600 Chris Morgan
2026-05-09 19:18 ` [PATCH V5 02/11] dt-bindings: iio: imu: icm42600: Add icm42607 binding Chris Morgan
2026-05-09 19:18 ` [PATCH V5 03/11] iio: imu: inv_icm42607: Add inv_icm42607 Core Driver Chris Morgan
2026-05-09 19:18 ` [PATCH V5 04/11] iio: imu: inv_icm42607: Add I2C and SPI For icm42607 Chris Morgan
2026-05-09 19:18 ` Chris Morgan [this message]
2026-05-09 19:19 ` [PATCH V5 06/11] iio: imu: inv_icm42607: Add Buffer support for icm42607 Chris Morgan
2026-05-09 19:19 ` [PATCH V5 07/11] iio: imu: inv_icm42607: Add Temp Support in icm42607 Chris Morgan
2026-05-09 19:19 ` [PATCH V5 08/11] iio: imu: inv_icm42607: Add Accelerometer for icm42607 Chris Morgan
2026-05-09 19:19 ` [PATCH V5 09/11] iio: imu: inv_icm42607: Add Wake on Movement to icm42607 Chris Morgan
2026-05-09 19:19 ` [PATCH V5 10/11] iio: imu: inv_icm42607: Add Gyroscope " Chris Morgan
2026-05-09 19:19 ` [PATCH V5 11/11] arm64: dts: rockchip: Add icm42607p IMU for RG-DS Chris Morgan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260509191907.24734-6-macroalpha82@gmail.com \
--to=macroalpha82@gmail.com \
--cc=andriy.shevchenko@intel.com \
--cc=andy@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dlechner@baylibre.com \
--cc=heiko@sntech.de \
--cc=jean-baptiste.maneyrol@tdk.com \
--cc=jic23@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=macromorgan@hotmail.com \
--cc=nuno.sa@analog.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox