* Re: [PATCH v3 3/6] dt-bindings: gpio: trivial-gpio: remove max77620 compatible
From: Krzysztof Kozlowski @ 2026-03-07 12:42 UTC (permalink / raw)
To: Svyatoslav Ryhel
Cc: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Lee Jones, Liam Girdwood,
Mark Brown, Rafael J. Wysocki, Daniel Lezcano, Zhang Rui,
Lukasz Luba, Chanwoo Choi, Alexandre Belloni, linux-gpio,
devicetree, linux-kernel, linux-pm, linux-rtc
In-Reply-To: <20260306133351.31589-4-clamor95@gmail.com>
On Fri, Mar 06, 2026 at 03:33:48PM +0200, Svyatoslav Ryhel wrote:
> Binding for MAX77620 GPIO function is covered by the MAX77620 schema. GPIO
> controller function in MAX77620 has no dedicated node and is folded into
> the parent node itself.
>
> Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
> ---
> Documentation/devicetree/bindings/gpio/trivial-gpio.yaml | 2 --
> 1 file changed, 2 deletions(-)
This should be squashed with the converting patch for this compatible.
Best regards,
Krzysztof
^ permalink raw reply
* Re: [PATCH v2 0/6] Remove use of i2c_match_id in RTC
From: Alexandre Belloni @ 2026-03-07 0:09 UTC (permalink / raw)
To: Andrew Davis; +Cc: linux-rtc, linux-kernel
In-Reply-To: <5c4c2470-70ee-4dd4-b769-9f26206145d4@ti.com>
On 06/03/2026 09:01:00-0600, Andrew Davis wrote:
> On 3/5/26 5:07 PM, Alexandre Belloni wrote:
> > On 05/03/2026 13:35:39-0600, Andrew Davis wrote:
> > > Hello all,
> > >
> > > RTC subsystem is one of the last still using i2c_match_id().
> > > This is a v2 but nothing is changed from last time. If I'm
> > > not sending this to the right folks let me know.
> >
> > Do you mean that you intend to remove i2c_match_id from the kernel?
> >
>
> Yes, once I remove all users in the various subsystems (like RTC),
> I'll remove it from the I2C headers.
>
> It should be replaced with functions like i2c_get_match_data()
> for reasons given in the commit messages.
Ok, this should have been made clear in the original cover letter, the
series would have looked a bit less like unnecessary churn.
>
> Andrew
>
> > >
> > > Thanks,
> > > Andrew
> > >
> > > Andrew Davis (6):
> > > rtc: abx80x: Remove use of i2c_match_id()
> > > rtc: m41t80: Remove use of i2c_match_id()
> > > rtc: pcf2127: Remove use of i2c_match_id()
> > > rtc: rs5c372: Remove use of i2c_match_id()
> > > rtc: rv8803: Remove use of i2c_match_id()
> > > rtc: rx8025: Remove use of i2c_match_id()
> > >
> > > drivers/rtc/rtc-abx80x.c | 3 +--
> > > drivers/rtc/rtc-m41t80.c | 8 +-------
> > > drivers/rtc/rtc-pcf2127.c | 23 +++++++----------------
> > > drivers/rtc/rtc-rs5c372.c | 7 +------
> > > drivers/rtc/rtc-rv8803.c | 8 +-------
> > > drivers/rtc/rtc-rx8025.c | 4 +---
> > > 6 files changed, 12 insertions(+), 41 deletions(-)
> > >
> > > --
> > > 2.39.2
> > >
> >
>
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply
* Re: [PATCH v3 2/6] dt-binding: pinctrl: pinctrl-max77620: convert to DT schema
From: Rob Herring (Arm) @ 2026-03-06 15:33 UTC (permalink / raw)
To: Svyatoslav Ryhel
Cc: Mark Brown, Bartosz Golaszewski, Rafael J. Wysocki, linux-rtc,
Alexandre Belloni, Lee Jones, Zhang Rui, Krzysztof Kozlowski,
devicetree, linux-kernel, Liam Girdwood, linux-pm, Linus Walleij,
Chanwoo Choi, Conor Dooley, linux-gpio, Daniel Lezcano,
Lukasz Luba
In-Reply-To: <20260306133351.31589-3-clamor95@gmail.com>
On Fri, 06 Mar 2026 15:33:47 +0200, Svyatoslav Ryhel wrote:
> Convert pinctrl-max77620 devicetree bindings for the MAX77620 PMIC from
> TXT to YAML format. This patch does not change any functionality; the
> bindings remain the same.
>
> Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
> ---
> .../pinctrl/maxim,max77620-pinctrl.yaml | 97 +++++++++++++
> .../bindings/pinctrl/pinctrl-max77620.txt | 127 ------------------
> 2 files changed, 97 insertions(+), 127 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/maxim,max77620-pinctrl.yaml
> delete mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt
>
My bot found errors running 'make dt_binding_check' on your patch:
yamllint warnings/errors:
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/maxim,max77620-pinctrl.yaml: patternProperties:^(pin_gpio|gpio)[0-7_]+$:properties:pins: 'enum' should not be valid under {'enum': ['const', 'enum', 'exclusiveMaximum', 'exclusiveMinimum', 'minimum', 'maximum', 'multipleOf', 'pattern']}
hint: Scalar and array keywords cannot be mixed
from schema $id: http://devicetree.org/meta-schemas/keywords.yaml
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/pinctrl/maxim,max77620-pinctrl.yaml: patternProperties:^(pin_gpio|gpio)[0-7_]+$:properties:pins: 'enum' should not be valid under {'enum': ['const', 'enum', 'exclusiveMaximum', 'exclusiveMinimum', 'minimum', 'maximum', 'multipleOf', 'pattern']}
hint: Scalar and array keywords cannot be mixed
from schema $id: http://devicetree.org/meta-schemas/keywords.yaml
doc reference errors (make refcheckdocs):
See https://patchwork.kernel.org/project/devicetree/patch/20260306133351.31589-3-clamor95@gmail.com
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
^ permalink raw reply
* Re: [PATCH v2 0/6] Remove use of i2c_match_id in RTC
From: Andrew Davis @ 2026-03-06 15:01 UTC (permalink / raw)
To: Alexandre Belloni; +Cc: linux-rtc, linux-kernel
In-Reply-To: <20260305230725ffa875be@mail.local>
On 3/5/26 5:07 PM, Alexandre Belloni wrote:
> On 05/03/2026 13:35:39-0600, Andrew Davis wrote:
>> Hello all,
>>
>> RTC subsystem is one of the last still using i2c_match_id().
>> This is a v2 but nothing is changed from last time. If I'm
>> not sending this to the right folks let me know.
>
> Do you mean that you intend to remove i2c_match_id from the kernel?
>
Yes, once I remove all users in the various subsystems (like RTC),
I'll remove it from the I2C headers.
It should be replaced with functions like i2c_get_match_data()
for reasons given in the commit messages.
Andrew
>>
>> Thanks,
>> Andrew
>>
>> Andrew Davis (6):
>> rtc: abx80x: Remove use of i2c_match_id()
>> rtc: m41t80: Remove use of i2c_match_id()
>> rtc: pcf2127: Remove use of i2c_match_id()
>> rtc: rs5c372: Remove use of i2c_match_id()
>> rtc: rv8803: Remove use of i2c_match_id()
>> rtc: rx8025: Remove use of i2c_match_id()
>>
>> drivers/rtc/rtc-abx80x.c | 3 +--
>> drivers/rtc/rtc-m41t80.c | 8 +-------
>> drivers/rtc/rtc-pcf2127.c | 23 +++++++----------------
>> drivers/rtc/rtc-rs5c372.c | 7 +------
>> drivers/rtc/rtc-rv8803.c | 8 +-------
>> drivers/rtc/rtc-rx8025.c | 4 +---
>> 6 files changed, 12 insertions(+), 41 deletions(-)
>>
>> --
>> 2.39.2
>>
>
^ permalink raw reply
* Re: [PATCH v3 1/6] regulator: dt-binding: regulator-max77620: convert to DT schema
From: Mark Brown @ 2026-03-06 13:39 UTC (permalink / raw)
To: Svyatoslav Ryhel
Cc: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Lee Jones, Liam Girdwood,
Rafael J. Wysocki, Daniel Lezcano, Zhang Rui, Lukasz Luba,
Chanwoo Choi, Alexandre Belloni, linux-gpio, devicetree,
linux-kernel, linux-pm, linux-rtc
In-Reply-To: <20260306133351.31589-2-clamor95@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 285 bytes --]
On Fri, Mar 06, 2026 at 03:33:46PM +0200, Svyatoslav Ryhel wrote:
> Convert regulator-max77620 devicetree bindings for the MAX77620 PMIC from
> TXT to YAML format. This patch does not change any functionality; the
> bindings remain the same.
Acked-by: Mark Brown <broonie@kernel.org>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply
* [PATCH v3 6/6] rtc: max77686: convert to i2c_new_ancillary_device
From: Svyatoslav Ryhel @ 2026-03-06 13:33 UTC (permalink / raw)
To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Lee Jones, Liam Girdwood,
Mark Brown, Rafael J. Wysocki, Daniel Lezcano, Zhang Rui,
Lukasz Luba, Chanwoo Choi, Alexandre Belloni, Svyatoslav Ryhel
Cc: linux-gpio, devicetree, linux-kernel, linux-pm, linux-rtc
In-Reply-To: <20260306133351.31589-1-clamor95@gmail.com>
Convert RTC I2C device creation from devm_i2c_new_dummy_device() to
i2c_new_ancillary_device() to enable the use of a device tree-specified
RTC address instead of a hardcoded value. If the device tree does not
provide an address, use hardcoded values as a fallback.
This addresses an issue with the MAX77663 PMIC, which can have the RTC at
different I2C positions (either 0x48, like the MAX77714, or 0x68, like
the MAX77620). The MAX77620 value is used as the default. The I2C position
of the MAX77663 is factory-set and cannot be detected from the chip
itself.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
---
drivers/rtc/rtc-max77686.c | 14 ++++++++++++--
1 file changed, 12 insertions(+), 2 deletions(-)
diff --git a/drivers/rtc/rtc-max77686.c b/drivers/rtc/rtc-max77686.c
index 69ea3ce75b5a..3cdfd78a07cc 100644
--- a/drivers/rtc/rtc-max77686.c
+++ b/drivers/rtc/rtc-max77686.c
@@ -686,6 +686,11 @@ static int max77686_rtc_init_reg(struct max77686_rtc_info *info)
return ret;
}
+static void max77686_rtc_release_dev(void *client)
+{
+ i2c_unregister_device(client);
+}
+
static int max77686_init_rtc_regmap(struct max77686_rtc_info *info)
{
struct device *parent = info->dev->parent;
@@ -713,12 +718,17 @@ static int max77686_init_rtc_regmap(struct max77686_rtc_info *info)
goto add_rtc_irq;
}
- client = devm_i2c_new_dummy_device(info->dev, parent_i2c->adapter,
- info->drv_data->rtc_i2c_addr);
+ client = i2c_new_ancillary_device(parent_i2c, "rtc",
+ info->drv_data->rtc_i2c_addr);
if (IS_ERR(client))
return dev_err_probe(info->dev, PTR_ERR(client),
"Failed to allocate I2C device for RTC\n");
+ ret = devm_add_action_or_reset(info->dev, max77686_rtc_release_dev,
+ client);
+ if (ret)
+ return ret;
+
info->rtc_regmap = devm_regmap_init_i2c(client,
info->drv_data->regmap_config);
if (IS_ERR(info->rtc_regmap))
--
2.51.0
^ permalink raw reply related
* [PATCH v3 5/6] dt-bindings: mfd: max77620: document optional RTC address for MAX77663
From: Svyatoslav Ryhel @ 2026-03-06 13:33 UTC (permalink / raw)
To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Lee Jones, Liam Girdwood,
Mark Brown, Rafael J. Wysocki, Daniel Lezcano, Zhang Rui,
Lukasz Luba, Chanwoo Choi, Alexandre Belloni, Svyatoslav Ryhel
Cc: linux-gpio, devicetree, linux-kernel, linux-pm, linux-rtc
In-Reply-To: <20260306133351.31589-1-clamor95@gmail.com>
Document an optional second I2C address for the MAX77663 PMIC's RTC
device, to be used if the MAX77663 RTC is located at a non-default I2C
address.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
---
.../bindings/mfd/maxim,max77620.yaml | 22 ++++++++++++++++++-
1 file changed, 21 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/mfd/maxim,max77620.yaml b/Documentation/devicetree/bindings/mfd/maxim,max77620.yaml
index 42cbad56595f..246c7f9e572d 100644
--- a/Documentation/devicetree/bindings/mfd/maxim,max77620.yaml
+++ b/Documentation/devicetree/bindings/mfd/maxim,max77620.yaml
@@ -17,7 +17,17 @@ properties:
- maxim,max77663
reg:
- maxItems: 1
+ description:
+ Can contain an optional second I2C address pointing to the PMIC's
+ RTC device. If no RTC address is provided, a default address specific
+ to this PMIC will be used.
+ minItems: 1
+ maxItems: 2
+
+ reg-names:
+ items:
+ - const: pmic
+ - const: rtc
interrupts:
maxItems: 1
@@ -192,6 +202,16 @@ allOf:
maxim,suspend-fps-time-period-us:
enum: [40, 80, 160, 320, 640, 1280, 2560, 5120]
+ - if:
+ properties:
+ compatible:
+ not:
+ contains:
+ const: maxim,max77663
+ then:
+ properties:
+ reg-names: false
+
required:
- compatible
- reg
--
2.51.0
^ permalink raw reply related
* [PATCH v3 4/6] dt-bindings: mfd: max77620: convert to DT schema
From: Svyatoslav Ryhel @ 2026-03-06 13:33 UTC (permalink / raw)
To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Lee Jones, Liam Girdwood,
Mark Brown, Rafael J. Wysocki, Daniel Lezcano, Zhang Rui,
Lukasz Luba, Chanwoo Choi, Alexandre Belloni, Svyatoslav Ryhel
Cc: linux-gpio, devicetree, linux-kernel, linux-pm, linux-rtc
In-Reply-To: <20260306133351.31589-1-clamor95@gmail.com>
Convert max77620 devicetree bindings from TXT to YAML format. This patch
does not change any functionality; the bindings remain the same. The
thermal bindings are incorporated into the binding.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
---
.../devicetree/bindings/mfd/max77620.txt | 162 -------
.../bindings/mfd/maxim,max77620.yaml | 422 ++++++++++++++++++
.../bindings/thermal/max77620_thermal.txt | 70 ---
3 files changed, 422 insertions(+), 232 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/mfd/max77620.txt
create mode 100644 Documentation/devicetree/bindings/mfd/maxim,max77620.yaml
delete mode 100644 Documentation/devicetree/bindings/thermal/max77620_thermal.txt
diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt
deleted file mode 100644
index 5a642a51d58e..000000000000
--- a/Documentation/devicetree/bindings/mfd/max77620.txt
+++ /dev/null
@@ -1,162 +0,0 @@
-MAX77620 Power management IC from Maxim Semiconductor.
-
-Required properties:
--------------------
-- compatible: Must be one of
- "maxim,max77620"
- "maxim,max20024"
- "maxim,max77663"
-- reg: I2C device address.
-
-Optional properties:
--------------------
-- interrupts: The interrupt on the parent the controller is
- connected to.
-- interrupt-controller: Marks the device node as an interrupt controller.
-- #interrupt-cells: is <2> and their usage is compliant to the 2 cells
- variant of <../interrupt-controller/interrupts.txt>
- IRQ numbers for different interrupt source of MAX77620
- are defined at dt-bindings/mfd/max77620.h.
-
-- system-power-controller: Indicates that this PMIC is controlling the
- system power, see [1] for more details.
-
-[1] Documentation/devicetree/bindings/power/power-controller.txt
-
-Optional subnodes and their properties:
-=======================================
-
-Flexible power sequence configurations:
---------------------------------------
-The Flexible Power Sequencer (FPS) allows each regulator to power up under
-hardware or software control. Additionally, each regulator can power on
-independently or among a group of other regulators with an adjustable power-up
-and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed
-to be part of a sequence allowing external regulators to be sequenced along
-with internal regulators. 32KHz clock can be programmed to be part of a
-sequence.
-
-The flexible sequencing structure consists of two hardware enable inputs
-(EN0, EN1), and 3 master sequencing timers called FPS0, FPS1 and FPS2.
-Each master sequencing timer is programmable through its configuration
-register to have a hardware enable source (EN1 or EN2) or a software enable
-source (SW). When enabled/disabled, the master sequencing timer generates
-eight sequencing events on different time periods called slots. The time
-period between each event is programmable within the configuration register.
-Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power
-sequence slave register which allows its enable source to be specified as
-a flexible power sequencer timer or a software bit. When a FPS source of
-regulators, GPIOs and clocks specifies the enable source to be a flexible
-power sequencer, the power up and power down delays can be specified in
-the regulators, GPIOs and clocks flexible power sequencer configuration
-registers.
-
-When FPS event cleared (set to LOW), regulators, GPIOs and 32KHz
-clock are set into following state at the sequencing event that
-corresponds to its flexible sequencer configuration register.
- Sleep state: In this state, regulators, GPIOs
- and 32KHz clock get disabled at
- the sequencing event.
- Global Low Power Mode (GLPM): In this state, regulators are set in
- low power mode at the sequencing event.
-
-The configuration parameters of FPS is provided through sub-node "fps"
-and their child for FPS specific. The child node name for FPS are "fps0",
-"fps1", and "fps2" for FPS0, FPS1 and FPS2 respectively.
-
-The FPS configurations like FPS source, power up and power down slots for
-regulators, GPIOs and 32kHz clocks are provided in their respective
-configuration nodes which is explained in respective sub-system DT
-binding document.
-
-There is need for different FPS configuration parameters based on system
-state like when system state changed from active to suspend or active to
-power off (shutdown).
-
-Optional properties:
--------------------
--maxim,fps-event-source: u32, FPS event source like external
- hardware input to PMIC i.e. EN0, EN1 or
- software (SW).
- The macros are defined on
- dt-bindings/mfd/max77620.h
- for different control source.
- - MAX77620_FPS_EVENT_SRC_EN0
- for hardware input pin EN0.
- - MAX77620_FPS_EVENT_SRC_EN1
- for hardware input pin EN1.
- - MAX77620_FPS_EVENT_SRC_SW
- for software control.
-
--maxim,shutdown-fps-time-period-us: u32, FPS time period in microseconds
- when system enters in to shutdown
- state.
-
--maxim,suspend-fps-time-period-us: u32, FPS time period in microseconds
- when system enters in to suspend state.
-
--maxim,device-state-on-disabled-event: u32, describe the PMIC state when FPS
- event cleared (set to LOW) whether it
- should go to sleep state or low-power
- state. Following are valid values:
- - MAX77620_FPS_INACTIVE_STATE_SLEEP
- to set the PMIC state to sleep.
- - MAX77620_FPS_INACTIVE_STATE_LOW_POWER
- to set the PMIC state to low
- power.
- Absence of this property or other value
- will not change device state when FPS
- event get cleared.
-
-Here supported time periods by device in microseconds are as follows:
-MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds.
-MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
-MAX77663 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
-
--maxim,power-ok-control: configure map power ok bit
- 1: Enables POK(Power OK) to control nRST_IO and GPIO1
- POK function.
- 0: Disables POK control.
- if property missing, do not configure MPOK bit.
- If POK mapping is enabled for GPIO1/nRST_IO then,
- GPIO1/nRST_IO pins are HIGH only if all rails
- that have POK control enabled are HIGH.
- If any of the rails goes down(which are enabled for POK
- control) then, GPIO1/nRST_IO goes LOW.
- this property is valid for max20024 only.
-
-For DT binding details of different sub modules like GPIO, pincontrol,
-regulator, power, please refer respective device-tree binding document
-under their respective sub-system directories.
-
-Example:
---------
-#include <dt-bindings/mfd/max77620.h>
-
-max77620@3c {
- compatible = "maxim,max77620";
- reg = <0x3c>;
-
- interrupt-parent = <&intc>;
- interrupts = <0 86 IRQ_TYPE_NONE>;
-
- interrupt-controller;
- #interrupt-cells = <2>;
-
- fps {
- fps0 {
- maxim,shutdown-fps-time-period-us = <1280>;
- maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
- };
-
- fps1 {
- maxim,shutdown-fps-time-period-us = <1280>;
- maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
- };
-
- fps2 {
- maxim,shutdown-fps-time-period-us = <1280>;
- maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_SW>;
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/mfd/maxim,max77620.yaml b/Documentation/devicetree/bindings/mfd/maxim,max77620.yaml
new file mode 100644
index 000000000000..42cbad56595f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/maxim,max77620.yaml
@@ -0,0 +1,422 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/maxim,max77620.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MAX77620 Power management IC from Maxim Semiconductor
+
+maintainers:
+ - Svyatoslav Ryhel <clamor95@gmail.com>
+
+properties:
+ compatible:
+ enum:
+ - maxim,max20024
+ - maxim,max77620
+ - maxim,max77663
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 2
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ const: 2
+ description:
+ Device has 8 GPIO pins which can be configured as GPIO as well as
+ the special IO functions. The first cell is the pin number, and the
+ second cell is used to specify the gpio polarity (GPIO_ACTIVE_HIGH or
+ GPIO_ACTIVE_LOW).
+
+ system-power-controller: true
+
+ "#thermal-sensor-cells":
+ const: 0
+ description:
+ Maxim Semiconductor MAX77620 supports alarm interrupts when its
+ die temperature crosses 120C and 140C. These threshold temperatures
+ are not configurable. Device does not provide the real temperature
+ of die other than just indicating whether temperature is above or
+ below threshold level.
+
+ fps:
+ type: object
+ additionalProperties: false
+ description: |
+ The Flexible Power Sequencer (FPS) allows each regulator to power up
+ under hardware or software control. Additionally, each regulator can
+ power on independently or among a group of other regulators with an
+ adjustable power-up and power-down delays (sequencing). GPIO1, GPIO2,
+ and GPIO3 can be programmed to be part of a sequence allowing external
+ regulators to be sequenced along with internal regulators. 32KHz clock
+ can be programmed to be part of a sequence.
+
+ The flexible sequencing structure consists of two hardware enable inputs
+ (EN0, EN1), and 3 master sequencing timers called FPS0, FPS1 and FPS2.
+ Each master sequencing timer is programmable through its configuration
+ register to have a hardware enable source (EN1 or EN2) or a software enable
+ source (SW). When enabled/disabled, the master sequencing timer generates
+ eight sequencing events on different time periods called slots. The time
+ period between each event is programmable within the configuration register.
+ Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power
+ sequence slave register which allows its enable source to be specified as
+ a flexible power sequencer timer or a software bit. When a FPS source of
+ regulators, GPIOs and clocks specifies the enable source to be a flexible
+ power sequencer, the power up and power down delays can be specified in
+ the regulators, GPIOs and clocks flexible power sequencer configuration
+ registers.
+
+ When FPS event cleared (set to LOW), regulators, GPIOs and 32KHz clock
+ are set into following state at the sequencing event that corresponds
+ to its flexible sequencer configuration register.
+
+ Sleep state: In this state, regulators, GPIOs and 32KHz clock get disabled
+ at the sequencing event.
+ Global Low Power Mode (GLPM): In this state, regulators are set in low
+ power mode at the sequencing event.
+
+ The configuration parameters of FPS is provided through sub-node "fps"
+ and their child for FPS specific. The child node name for FPS are "fps0",
+ "fps1", and "fps2" for FPS0, FPS1 and FPS2 respectively.
+
+ The FPS configurations like FPS source, power up and power down slots for
+ regulators, GPIOs and 32kHz clocks are provided in their respective
+ configuration nodes which is explained in respective sub-system DT
+ binding document.
+
+ There is need for different FPS configuration parameters based on system
+ state like when system state changed from active to suspend or active to
+ power off (shutdown).
+
+ patternProperties:
+ "^fps[0-2]$":
+ type: object
+ additionalProperties: false
+
+ properties:
+ maxim,fps-event-source:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ FPS event source like external hardware input to PMIC i.e. EN0, EN1
+ or software (SW).
+
+ The macros are defined on dt-bindings/mfd/max77620.h for different
+ control source.
+ - MAX77620_FPS_EVENT_SRC_EN0 for hardware input pin EN0.
+ - MAX77620_FPS_EVENT_SRC_EN1 for hardware input pin EN1.
+ - MAX77620_FPS_EVENT_SRC_SW for software control.
+
+ maxim,shutdown-fps-time-period-us:
+ description:
+ FPS time period in microseconds when system enters in to shutdown state.
+
+ maxim,suspend-fps-time-period-us:
+ description:
+ FPS time period in microseconds when system enters in to suspend state.
+
+ maxim,device-state-on-disabled-event:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Describe the PMIC state when FPS event cleared (set to LOW) whether it
+ should go to sleep state or low-power state. Following are valid values:
+ - MAX77620_FPS_INACTIVE_STATE_SLEEP to set the PMIC state to sleep.
+ - MAX77620_FPS_INACTIVE_STATE_LOW_POWER to set the PMIC state to low
+ power.
+ Absence of this property or other value will not change device state
+ when FPS event get cleared.
+
+ maxim,power-ok-control:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Configure map power ok bit
+
+ 1: Enables POK(Power OK) to control nRST_IO and GPIO1 POK function.
+ 0: Disables POK control.
+
+ If property missing, do not configure MPOK bit. If POK mapping is
+ enabled for GPIO1/nRST_IO then, GPIO1/nRST_IO pins are HIGH only if
+ all rails that have POK control enabled are HIGH. If any of the rails
+ goes down (which are enabled for POK control) then, GPIO1/nRST_IO
+ goes LOW.
+ enum: [0, 1]
+
+ pinmux:
+ $ref: /schemas/pinctrl/maxim,max77620-pinctrl.yaml
+
+ regulators:
+ $ref: /schemas/regulator/maxim,max77620-regulator.yaml
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - maxim,max20024
+ - maxim,max77663
+ then:
+ properties:
+ "#thermal-sensor-cells": false
+ fps:
+ patternProperties:
+ "^fps[0-2]$":
+ properties:
+ maxim,shutdown-fps-time-period-us:
+ enum: [20, 40, 80, 160, 320, 640, 1280, 2540]
+ maxim,suspend-fps-time-period-us:
+ enum: [20, 40, 80, 160, 320, 640, 1280, 2540]
+ maxim,power-ok-control: false
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: maxim,max77620
+ then:
+ properties:
+ fps:
+ patternProperties:
+ "^fps[0-2]$":
+ properties:
+ maxim,shutdown-fps-time-period-us:
+ enum: [40, 80, 160, 320, 640, 1280, 2560, 5120]
+ maxim,suspend-fps-time-period-us:
+ enum: [40, 80, 160, 320, 640, 1280, 2560, 5120]
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/mfd/max77620.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@3c {
+ compatible = "maxim,max77620";
+ reg = <0x3c>;
+
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ #thermal-sensor-cells = <0>;
+
+ system-power-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77620_default>;
+
+ max77620_default: pinmux {
+ gpio0 {
+ pins = "gpio0";
+ function = "gpio";
+ };
+
+ gpio1 {
+ pins = "gpio1";
+ function = "fps-out";
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ };
+
+ gpio2 {
+ pins = "gpio2";
+ function = "fps-out";
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ };
+
+ gpio3 {
+ pins = "gpio3";
+ function = "gpio";
+ };
+
+ gpio4 {
+ pins = "gpio4";
+ function = "32k-out1";
+ };
+
+ gpio5_6 {
+ pins = "gpio5", "gpio6";
+ function = "gpio";
+ drive-push-pull = <1>;
+ };
+
+ gpio7 {
+ pins = "gpio7";
+ function = "gpio";
+ };
+ };
+
+ fps {
+ fps0 {
+ maxim,shutdown-fps-time-period-us = <1280>;
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+ };
+
+ fps1 {
+ maxim,shutdown-fps-time-period-us = <1280>;
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
+ };
+
+ fps2 {
+ maxim,shutdown-fps-time-period-us = <1280>;
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_SW>;
+ };
+ };
+
+ regulators {
+ in-sd0-supply = <&vdd_5v0_vbus>;
+ in-sd1-supply = <&vdd_5v0_vbus>;
+ in-sd2-supply = <&vdd_5v0_vbus>;
+ in-sd3-supply = <&vdd_5v0_vbus>;
+
+ in-ldo0-1-supply = <&vdd_1v8_vio>;
+ in-ldo2-supply = <&vdd_3v3_vbat>;
+ in-ldo3-5-supply = <&vdd_3v3_vbat>;
+ in-ldo4-6-supply = <&vdd_3v3_vbat>;
+ in-ldo7-8-supply = <&vdd_1v8_vio>;
+
+ sd0 {
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ sd1 {
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ };
+
+ vdd_1v8_vio: sd2 {
+ regulator-name = "vdd_1v8_gen";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ sd3 {
+ regulator-name = "vddio_ddr";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ ldo0 {
+ regulator-name = "avdd_pll";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ };
+
+ ldo1 {
+ regulator-name = "vdd_ddr_hs";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ ldo2 {
+ regulator-name = "avdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ ldo3 {
+ regulator-name = "vdd_sdmmc3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ ldo4 {
+ regulator-name = "vdd_rtc";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ };
+
+ ldo5 {
+ regulator-name = "vdd_ddr_rx";
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ };
+
+ ldo6 {
+ regulator-name = "avdd_osc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ ldo7 {
+ regulator-name = "vdd_1v2_mhl";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1250000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+
+ ldo8 {
+ regulator-name = "avdd_dsi_csi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ };
+ };
+ };
+ };
+...
diff --git a/Documentation/devicetree/bindings/thermal/max77620_thermal.txt b/Documentation/devicetree/bindings/thermal/max77620_thermal.txt
deleted file mode 100644
index 82ed5d487966..000000000000
--- a/Documentation/devicetree/bindings/thermal/max77620_thermal.txt
+++ /dev/null
@@ -1,70 +0,0 @@
-Thermal driver for MAX77620 Power management IC from Maxim Semiconductor.
-
-Maxim Semiconductor MAX77620 supports alarm interrupts when its
-die temperature crosses 120C and 140C. These threshold temperatures
-are not configurable. Device does not provide the real temperature
-of die other than just indicating whether temperature is above or
-below threshold level.
-
-Required properties:
--------------------
-#thermal-sensor-cells: For more details, please refer to
- <devicetree/bindings/thermal/thermal-sensor.yaml>
- The value must be 0.
-
-For more details, please refer generic thermal DT binding document
-<devicetree/bindings/thermal/thermal*.yaml>.
-
-Please refer <devicetree/bindings/mfd/max77620.txt> for mfd DT binding
-document for the MAX77620.
-
-Example:
---------
-#include <dt-bindings/mfd/max77620.h>
-#include <dt-bindings/thermal/thermal.h>
-...
-
-i2c@7000d000 {
- spmic: max77620@3c {
- compatible = "maxim,max77620";
- :::::
- #thermal-sensor-cells = <0>;
- :::
- };
-};
-
-cool_dev: cool-dev {
- compatible = "cooling-dev";
- #cooling-cells = <2>;
-};
-
-thermal-zones {
- PMIC-Die {
- polling-delay = <0>;
- polling-delay-passive = <0>;
- thermal-sensors = <&spmic>;
-
- trips {
- pmic_die_warn_temp_thresh: hot-die {
- temperature = <120000>;
- type = "hot";
- hysteresis = <0>;
- };
-
- pmic_die_cirt_temp_thresh: cirtical-die {
- temperature = <140000>;
- type = "critical";
- hysteresis = <0>;
- };
- };
-
- cooling-maps {
- map0 {
- trip = <&pmic_die_warn_temp_thresh>;
- cooling-device = <&cool_dev THERMAL_NO_LIMIT
- THERMAL_NO_LIMIT>;
- contribution = <100>;
- };
- };
- };
-};
--
2.51.0
^ permalink raw reply related
* [PATCH v3 3/6] dt-bindings: gpio: trivial-gpio: remove max77620 compatible
From: Svyatoslav Ryhel @ 2026-03-06 13:33 UTC (permalink / raw)
To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Lee Jones, Liam Girdwood,
Mark Brown, Rafael J. Wysocki, Daniel Lezcano, Zhang Rui,
Lukasz Luba, Chanwoo Choi, Alexandre Belloni, Svyatoslav Ryhel
Cc: linux-gpio, devicetree, linux-kernel, linux-pm, linux-rtc
In-Reply-To: <20260306133351.31589-1-clamor95@gmail.com>
Binding for MAX77620 GPIO function is covered by the MAX77620 schema. GPIO
controller function in MAX77620 has no dedicated node and is folded into
the parent node itself.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
---
Documentation/devicetree/bindings/gpio/trivial-gpio.yaml | 2 --
1 file changed, 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/gpio/trivial-gpio.yaml b/Documentation/devicetree/bindings/gpio/trivial-gpio.yaml
index 3f4bbd57fc52..fe9b14a72d69 100644
--- a/Documentation/devicetree/bindings/gpio/trivial-gpio.yaml
+++ b/Documentation/devicetree/bindings/gpio/trivial-gpio.yaml
@@ -27,7 +27,6 @@ properties:
- gateworks,pld-gpio
- ibm,ppc4xx-gpio
- loongson,ls1x-gpio
- - maxim,max77620
- nintendo,hollywood-gpio
- nxp,pca9570
- nxp,pca9571
@@ -86,7 +85,6 @@ allOf:
compatible:
contains:
enum:
- - maxim,max77620
- rockchip,rk3328-grf-gpio
- ti,lp3943-gpio
- ti,palmas-gpio
--
2.51.0
^ permalink raw reply related
* [PATCH v3 2/6] dt-binding: pinctrl: pinctrl-max77620: convert to DT schema
From: Svyatoslav Ryhel @ 2026-03-06 13:33 UTC (permalink / raw)
To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Lee Jones, Liam Girdwood,
Mark Brown, Rafael J. Wysocki, Daniel Lezcano, Zhang Rui,
Lukasz Luba, Chanwoo Choi, Alexandre Belloni, Svyatoslav Ryhel
Cc: linux-gpio, devicetree, linux-kernel, linux-pm, linux-rtc
In-Reply-To: <20260306133351.31589-1-clamor95@gmail.com>
Convert pinctrl-max77620 devicetree bindings for the MAX77620 PMIC from
TXT to YAML format. This patch does not change any functionality; the
bindings remain the same.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
---
.../pinctrl/maxim,max77620-pinctrl.yaml | 97 +++++++++++++
.../bindings/pinctrl/pinctrl-max77620.txt | 127 ------------------
2 files changed, 97 insertions(+), 127 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pinctrl/maxim,max77620-pinctrl.yaml
delete mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/maxim,max77620-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/maxim,max77620-pinctrl.yaml
new file mode 100644
index 000000000000..7364a8bdd7d3
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/maxim,max77620-pinctrl.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/maxim,max77620-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Pinmux controller function for Maxim MAX77620 Power management IC
+
+maintainers:
+ - Svyatoslav Ryhel <clamor95@gmail.com>
+
+description:
+ Device has 8 GPIO pins which can be configured as GPIO as well as the
+ special IO functions.
+
+allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+
+patternProperties:
+ "^(pin_gpio|gpio)[0-7_]+$":
+ type: object
+
+ properties:
+ pins:
+ enum: [ gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7 ]
+ minItems: 1
+ maxItems: 8
+
+ function:
+ enum: [ gpio, lpm-control-in, fps-out, 32k-out1, sd0-dvs-in, sd1-dvs-in,
+ reference-out ]
+
+ drive-push-pull: true
+ drive-open-drain: true
+ bias-pull-up: true
+ bias-pull-down: true
+
+ maxim,active-fps-source:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ FPS source for the GPIOs to get enabled/disabled when system is in
+ active state. Valid values are:
+ - MAX77620_FPS_SRC_0: FPS source is FPS0.
+ - MAX77620_FPS_SRC_1: FPS source is FPS1
+ - MAX77620_FPS_SRC_2: FPS source is FPS2
+ - MAX77620_FPS_SRC_NONE: GPIO is not controlled by FPS events and
+ it gets enabled/disabled by register access.
+ Absence of this property will leave the FPS configuration register
+ for that GPIO to default configuration.
+
+ maxim,active-fps-power-up-slot:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Sequencing event slot number on which the GPIO get enabled when
+ master FPS input event set to HIGH. This is applicable if FPS source
+ is selected as FPS0, FPS1 or FPS2.
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ maxim,active-fps-power-down-slot:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Sequencing event slot number on which the GPIO get disabled when
+ master FPS input event set to LOW. This is applicable if FPS source
+ is selected as FPS0, FPS1 or FPS2.
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ maxim,suspend-fps-source:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ This is same as property "maxim,active-fps-source" but value get
+ configured when system enters in to suspend state.
+
+ maxim,suspend-fps-power-up-slot:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ This is same as property "maxim,active-fps-power-up-slot" but this
+ value get configured into FPS configuration register when system
+ enters into suspend. This is applicable if suspend state FPS source
+ is selected as FPS0, FPS1 or FPS2.
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ maxim,suspend-fps-power-down-slot:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ This is same as property "maxim,active-fps-power-down-slot" but this
+ value get configured into FPS configuration register when system
+ enters into suspend. This is applicable if suspend state FPS source
+ is selected as FPS0, FPS1 or FPS2.
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ required:
+ - pins
+
+additionalProperties: false
+
+# see maxim,max77620.yaml for an example
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt
deleted file mode 100644
index 28fbca180068..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt
+++ /dev/null
@@ -1,127 +0,0 @@
-Pincontrol driver for MAX77620 Power management IC from Maxim Semiconductor.
-
-Device has 8 GPIO pins which can be configured as GPIO as well as the
-special IO functions.
-
-Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt>
-for details of the common pinctrl bindings used by client devices,
-including the meaning of the phrase "pin configuration node".
-
-Optional Pinmux properties:
---------------------------
-Following properties are required if default setting of pins are required
-at boot.
-- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>.
-- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per
- <pinctrl-bindings.txt>.
-
-The pin configurations are defined as child of the pinctrl states node. Each
-sub-node have following properties:
-
-Required properties:
-------------------
-- pins: List of pins. Valid values of pins properties are:
- gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7.
-
-Optional properties:
--------------------
-Following are optional properties defined as pinmux DT binding document
-<pinctrl-bindings.txt>. Absence of properties will leave the configuration
-on default.
- function,
- drive-push-pull,
- drive-open-drain,
- bias-pull-up,
- bias-pull-down.
-
-Valid values for function properties are:
- gpio, lpm-control-in, fps-out, 32k-out, sd0-dvs-in, sd1-dvs-in,
- reference-out
-
-There are also customised properties for the GPIO1, GPIO2 and GPIO3. These
-customised properties are required to configure FPS configuration parameters
-of these GPIOs. Please refer <devicetree/bindings/mfd/max77620.txt> for more
-detail of Flexible Power Sequence (FPS).
-
-- maxim,active-fps-source: FPS source for the GPIOs to get
- enabled/disabled when system is in
- active state. Valid values are:
- - MAX77620_FPS_SRC_0,
- FPS source is FPS0.
- - MAX77620_FPS_SRC_1,
- FPS source is FPS1
- - MAX77620_FPS_SRC_2 and
- FPS source is FPS2
- - MAX77620_FPS_SRC_NONE.
- GPIO is not controlled
- by FPS events and it gets
- enabled/disabled by register
- access.
- Absence of this property will leave
- the FPS configuration register for that
- GPIO to default configuration.
-
-- maxim,active-fps-power-up-slot: Sequencing event slot number on which
- the GPIO get enabled when
- master FPS input event set to HIGH.
- Valid values are 0 to 7.
- This is applicable if FPS source is
- selected as FPS0, FPS1 or FPS2.
-
-- maxim,active-fps-power-down-slot: Sequencing event slot number on which
- the GPIO get disabled when master
- FPS input event set to LOW.
- Valid values are 0 to 7.
- This is applicable if FPS source is
- selected as FPS0, FPS1 or FPS2.
-
-- maxim,suspend-fps-source: This is same as property
- "maxim,active-fps-source" but value
- get configured when system enters in
- to suspend state.
-
-- maxim,suspend-fps-power-up-slot: This is same as property
- "maxim,active-fps-power-up-slot" but
- this value get configured into FPS
- configuration register when system
- enters into suspend.
- This is applicable if suspend state
- FPS source is selected as FPS0, FPS1 or
-
-- maxim,suspend-fps-power-down-slot: This is same as property
- "maxim,active-fps-power-down-slot" but
- this value get configured into FPS
- configuration register when system
- enters into suspend.
- This is applicable if suspend state
- FPS source is selected as FPS0, FPS1 or
- FPS2.
-
-Example:
---------
-#include <dt-bindings/mfd/max77620.h>
-...
-max77620@3c {
-
- pinctrl-names = "default";
- pinctrl-0 = <&spmic_default>;
-
- spmic_default: pinmux@0 {
- pin_gpio0 {
- pins = "gpio0";
- function = "gpio";
- };
-
- pin_gpio1 {
- pins = "gpio1";
- function = "fps-out";
- maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
- };
-
- pin_gpio2 {
- pins = "gpio2";
- function = "fps-out";
- maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
- };
- };
-};
--
2.51.0
^ permalink raw reply related
* [PATCH v3 1/6] regulator: dt-binding: regulator-max77620: convert to DT schema
From: Svyatoslav Ryhel @ 2026-03-06 13:33 UTC (permalink / raw)
To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Lee Jones, Liam Girdwood,
Mark Brown, Rafael J. Wysocki, Daniel Lezcano, Zhang Rui,
Lukasz Luba, Chanwoo Choi, Alexandre Belloni, Svyatoslav Ryhel
Cc: linux-gpio, devicetree, linux-kernel, linux-pm, linux-rtc
In-Reply-To: <20260306133351.31589-1-clamor95@gmail.com>
Convert regulator-max77620 devicetree bindings for the MAX77620 PMIC from
TXT to YAML format. This patch does not change any functionality; the
bindings remain the same.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
---
.../regulator/maxim,max77620-regulator.yaml | 99 ++++++++
.../bindings/regulator/regulator-max77620.txt | 222 ------------------
2 files changed, 99 insertions(+), 222 deletions(-)
create mode 100644 Documentation/devicetree/bindings/regulator/maxim,max77620-regulator.yaml
delete mode 100644 Documentation/devicetree/bindings/regulator/regulator-max77620.txt
diff --git a/Documentation/devicetree/bindings/regulator/maxim,max77620-regulator.yaml b/Documentation/devicetree/bindings/regulator/maxim,max77620-regulator.yaml
new file mode 100644
index 000000000000..e8c374cfaef9
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/maxim,max77620-regulator.yaml
@@ -0,0 +1,99 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/maxim,max77620-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Regulator for MAX77620 Power management IC from Maxim Semiconductor.
+
+maintainers:
+ - Svyatoslav Ryhel <clamor95@gmail.com>
+
+description:
+ Device has multiple DCDC(sd[0-3]) and LDOs(ldo[0-8]). The input supply
+ of these regulators are defined under parent device node. Details of
+ regulator properties are defined as child node under sub-node "regulators"
+ which is child node of device node.
+
+patternProperties:
+ "^in-(sd[0-3]|ldo(0-1|2|3-5|4-6|7-8))-supply$":
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: Input supply for DCDC or LDO
+
+ "^(sd[0-3]|ldo[0-8])$":
+ type: object
+ $ref: /schemas/regulator/regulator.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ maxim,active-fps-source:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ FPS source for the GPIOs to get enabled/disabled when system is in
+ active state. Valid values are:
+ - MAX77620_FPS_SRC_0: FPS source is FPS0.
+ - MAX77620_FPS_SRC_1: FPS source is FPS1
+ - MAX77620_FPS_SRC_2: FPS source is FPS2
+ - MAX77620_FPS_SRC_NONE: GPIO is not controlled by FPS events and
+ it gets enabled/disabled by register access.
+ Absence of this property will leave the FPS configuration register
+ for that GPIO to default configuration.
+
+ maxim,active-fps-power-up-slot:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Sequencing event slot number on which the GPIO get enabled when
+ master FPS input event set to HIGH. This is applicable if FPS source
+ is selected as FPS0, FPS1 or FPS2.
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ maxim,active-fps-power-down-slot:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Sequencing event slot number on which the GPIO get disabled when
+ master FPS input event set to LOW. This is applicable if FPS source
+ is selected as FPS0, FPS1 or FPS2.
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ maxim,suspend-fps-source:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ This is same as property "maxim,active-fps-source" but value get
+ configured when system enters in to suspend state.
+
+ maxim,suspend-fps-power-up-slot:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ This is same as property "maxim,active-fps-power-up-slot" but this
+ value get configured into FPS configuration register when system
+ enters into suspend. This is applicable if suspend state FPS source
+ is selected as FPS0, FPS1 or FPS2.
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ maxim,suspend-fps-power-down-slot:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ This is same as property "maxim,active-fps-power-down-slot" but this
+ value get configured into FPS configuration register when system
+ enters into suspend. This is applicable if suspend state FPS source
+ is selected as FPS0, FPS1 or FPS2.
+ enum: [0, 1, 2, 3, 4, 5, 6, 7]
+
+ maxim,ramp-rate-setting:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ Ramp rate(uV/us) setting to be configured to the device. The platform
+ may have different ramp rate than advertised ramp rate if it has design
+ variation from Maxim's recommended. On this case, platform specific
+ ramp rate is used for ramp time calculation and this property is used
+ for device register configurations. The measured ramp rate of platform
+ is provided by the regulator-ramp-delay.
+
+ Maxim Max77620 supports following ramp delay:
+ SD: 13.75mV/us, 27.5mV/us, 55mV/us
+ LDOs: 5mV/us, 100mV/us
+ enum: [5000, 13750, 27500, 55000, 100000]
+
+additionalProperties: false
+
+# see maxim,max77620.yaml for an example
diff --git a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt
deleted file mode 100644
index bcf788897e44..000000000000
--- a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt
+++ /dev/null
@@ -1,222 +0,0 @@
-Regulator DT binding for MAX77620 Power management IC from Maxim Semiconductor.
-
-Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply
-of these regulators are defined under parent device node.
-Details of regulator properties are defined as child node under
-sub-node "regulators" which is child node of device node.
-
-Please refer file <Documentation/devicetree/bindings/regulator/regulator.txt>
-for common regulator bindings used by client.
-
-Following are properties of parent node related to regulators.
-
-Optional properties:
--------------------
-The input supply of regulators are the optional properties on the
-parent device node. The input supply of these regulators are provided
-through following properties:
-in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins.
-in-sd1-supply: Input supply for SD1.
-in-sd2-supply: Input supply for SD2.
-in-sd3-supply: Input supply for SD3.
-in-ldo0-1-supply: Input supply for LDO0 and LDO1.
-in-ldo2-supply: Input supply for LDO2.
-in-ldo3-5-supply: Input supply for LDO3 and LDO5
-in-ldo4-6-supply: Input supply for LDO4 and LDO6.
-in-ldo7-8-supply: Input supply for LDO7 and LDO8.
-
-Optional sub nodes for regulators under "regulators" subnode:
-------------------------------------------------------------
-The subnodes name is the name of regulator and it must be one of:
- sd[0-3], ldo[0-8]
-
-Each sub-node should contain the constraints and initialization
-information for that regulator. The definition for each of these
-nodes is defined using the standard binding for regulators found at
-<Documentation/devicetree/bindings/regulator/regulator.txt>.
-
-There are also additional properties for SD/LDOs. These additional properties
-are required to configure FPS configuration parameters for SDs and LDOs.
-Please refer <devicetree/bindings/mfd/max77620.txt> for more detail of Flexible
-Power Sequence (FPS).
-Following are additional properties:
-
-- maxim,active-fps-source: FPS source for the regulators to get
- enabled/disabled when system is in
- active state. Valid values are:
- - MAX77620_FPS_SRC_0,
- FPS source is FPS0.
- - MAX77620_FPS_SRC_1,
- FPS source is FPS1
- - MAX77620_FPS_SRC_2 and
- FPS source is FPS2
- - MAX77620_FPS_SRC_NONE.
- Regulator is not controlled
- by FPS events and it gets
- enabled/disabled by register
- access.
- Absence of this property will leave
- the FPS configuration register for that
- regulator to default configuration.
-
-- maxim,active-fps-power-up-slot: Sequencing event slot number on which
- the regulator get enabled when
- master FPS input event set to HIGH.
- Valid values are 0 to 7.
- This is applicable if FPS source is
- selected as FPS0, FPS1 or FPS2.
-
-- maxim,active-fps-power-down-slot: Sequencing event slot number on which
- the regulator get disabled when master
- FPS input event set to LOW.
- Valid values are 0 to 7.
- This is applicable if FPS source is
- selected as FPS0, FPS1 or FPS2.
-
-- maxim,suspend-fps-source: This is same as property
- "maxim,active-fps-source" but value
- get configured when system enters in
- to suspend state.
-
-- maxim,suspend-fps-power-up-slot: This is same as property
- "maxim,active-fps-power-up-slot" but
- this value get configured into FPS
- configuration register when system
- enters into suspend.
- This is applicable if suspend state
- FPS source is selected as FPS0, FPS1 or
-
-- maxim,suspend-fps-power-down-slot: This is same as property
- "maxim,active-fps-power-down-slot" but
- this value get configured into FPS
- configuration register when system
- enters into suspend.
- This is applicable if suspend state
- FPS source is selected as FPS0, FPS1 or
- FPS2.
-- maxim,ramp-rate-setting: integer, ramp rate(uV/us) setting to be
- configured to the device.
- The platform may have different ramp
- rate than advertised ramp rate if it has
- design variation from Maxim's
- recommended. On this case, platform
- specific ramp rate is used for ramp time
- calculation and this property is used
- for device register configurations.
- The measured ramp rate of platform is
- provided by the regulator-ramp-delay
- as described in <devicetree/bindings/
- regulator/regulator.txt>.
- Maxim Max77620 supports following ramp
- delay:
- SD: 13.75mV/us, 27.5mV/us, 55mV/us
- LDOs: 5mV/us, 100mV/us
-
-Note: If the measured ramp delay is same as advertised ramp delay then it is not
-required to provide the ramp delay with property "maxim,ramp-rate-setting". The
-ramp rate can be provided by the regulator-ramp-delay which will be used for
-ramp time calculation for voltage change as well as for device configuration.
-
-Example:
---------
-#include <dt-bindings/mfd/max77620.h>
-...
-max77620@3c {
- in-ldo0-1-supply = <&max77620_sd2>;
- in-ldo7-8-supply = <&max77620_sd2>;
- regulators {
- sd0 {
- regulator-name = "vdd-core";
- regulator-min-microvolt = <600000>;
- regulator-max-microvolt = <1400000>;
- regulator-boot-on;
- regulator-always-on;
- maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
- };
-
- sd1 {
- regulator-name = "vddio-ddr";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
- };
-
- sd2 {
- regulator-name = "vdd-pre-reg";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- };
-
- sd3 {
- regulator-name = "vdd-1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo0 {
- regulator-name = "avdd-sys";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo1 {
- regulator-name = "vdd-pex";
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
-
- ldo2 {
- regulator-name = "vddio-sdmmc3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- };
-
- ldo3 {
- regulator-name = "vdd-cam-hv";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
-
- ldo4 {
- regulator-name = "vdd-rtc";
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1250000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo5 {
- regulator-name = "avdd-ts-hv";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- };
-
- ldo6 {
- regulator-name = "vdd-ts";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo7 {
- regulator-name = "vdd-gen-pll-edp";
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo8 {
- regulator-name = "vdd-hdmi-dp";
- regulator-min-microvolt = <1050000>;
- regulator-max-microvolt = <1050000>;
- };
- };
-};
--
2.51.0
^ permalink raw reply related
* [PATCH v3 0/6] rtc: max77686: convert to i2c_new_ancillary_device
From: Svyatoslav Ryhel @ 2026-03-06 13:33 UTC (permalink / raw)
To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Lee Jones, Liam Girdwood,
Mark Brown, Rafael J. Wysocki, Daniel Lezcano, Zhang Rui,
Lukasz Luba, Chanwoo Choi, Alexandre Belloni, Svyatoslav Ryhel
Cc: linux-gpio, devicetree, linux-kernel, linux-pm, linux-rtc
Convert RTC I2C device creation from devm_i2c_new_dummy_device() to
i2c_new_ancillary_device() to enable the use of a device tree-specified
RTC address instead of a hardcoded value. If the device tree does not
provide an address, use hardcoded values as a fallback.
This addresses an issue with the MAX77663 PMIC, which can have the RTC at
different I2C positions (either 0x48, like the MAX77714, or 0x68, like
the MAX77620). The MAX77620 value is used as the default. The I2C position
of the MAX77663 is factory-set and cannot be detected from the chip
itself.
I have tested this patch on LG Optimus Vu P895 with max77663 PMIC and
non-default RTC position. RTC is registered correctly.
---
Changes in v3
- max77620 files converted to DT schema.
Changes in v2
- dropped patch that changes max77686 and adjusted max77620 where max77663
is described.
---
Svyatoslav Ryhel (6):
regulator: dt-binding: regulator-max77620: convert to DT schema
dt-binding: pinctrl: pinctrl-max77620: convert to DT schema
dt-bindings: gpio: trivial-gpio: remove max77620 compatible
dt-bindings: mfd: max77620: convert to DT schema
dt-bindings: mfd: max77620: document optional RTC address for MAX77663
rtc: max77686: convert to i2c_new_ancillary_device
.../bindings/gpio/trivial-gpio.yaml | 2 -
.../devicetree/bindings/mfd/max77620.txt | 162 -------
.../bindings/mfd/maxim,max77620.yaml | 442 ++++++++++++++++++
.../pinctrl/maxim,max77620-pinctrl.yaml | 97 ++++
.../bindings/pinctrl/pinctrl-max77620.txt | 127 -----
.../regulator/maxim,max77620-regulator.yaml | 99 ++++
.../bindings/regulator/regulator-max77620.txt | 222 ---------
.../bindings/thermal/max77620_thermal.txt | 70 ---
drivers/rtc/rtc-max77686.c | 14 +-
9 files changed, 650 insertions(+), 585 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/mfd/max77620.txt
create mode 100644 Documentation/devicetree/bindings/mfd/maxim,max77620.yaml
create mode 100644 Documentation/devicetree/bindings/pinctrl/maxim,max77620-pinctrl.yaml
delete mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-max77620.txt
create mode 100644 Documentation/devicetree/bindings/regulator/maxim,max77620-regulator.yaml
delete mode 100644 Documentation/devicetree/bindings/regulator/regulator-max77620.txt
delete mode 100644 Documentation/devicetree/bindings/thermal/max77620_thermal.txt
--
2.51.0
^ permalink raw reply
* Re: [PATCH 1/5] clk: renesas: r9a09g056: Fix ordering of module clocks array
From: Geert Uytterhoeven @ 2026-03-06 12:35 UTC (permalink / raw)
To: Ovidiu Panait
Cc: claudiu.beznea.uj, alexandre.belloni, robh, krzk+dt, conor+dt,
magnus.damm, mturquette, sboyd, prabhakar.mahadev-lad.rj,
linux-rtc, linux-renesas-soc, devicetree, linux-kernel, linux-clk
In-Reply-To: <CAMuHMdWZKUjptQCqe_DK3C_g5d9Zhp3r3j6+dAfE1g==NH+ofw@mail.gmail.com>
On Mon, 26 Jan 2026 at 16:27, Geert Uytterhoeven <geert@linux-m68k.org> wrote:
> On Sun, 25 Jan 2026 at 20:27, Ovidiu Panait
> <ovidiu.panait.rb@renesas.com> wrote:
> > The r9a09g056_mod_clks array is sorted by CPG_CLKON register number and
> > bit position. Move the RSPI 0/1/2 module clock entries to their correct
> > position to restore the array sort order.
> >
> > Fixes: 1f76689d1715 ("clk: renesas: r9a09g056: Add entries for RSCIs")
> > Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
>
> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
> i.e. will queue in renesas-clk for v6.21.
Promoting to renesas-clk-fixes for v7.0, as I have other fixes.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply
* Re: [QUESTION] rtc: zynqmp: CALIB_RD reset behavior differs between ZynqMP and Versal
From: Alexandre Belloni @ 2026-03-06 11:13 UTC (permalink / raw)
To: Tomas Melin
Cc: Takumi Ando, linux-rtc, michal.simek, Yasushi SHOJI, kanta tamura
In-Reply-To: <9ed6823e-b381-4de5-b1cf-98f5dc54bb7c@vaisala.com>
On 06/03/2026 12:09:40+0200, Tomas Melin wrote:
> > On Zynq UltraScale+ Devices Register Reference (UG1087) [2],
> > CALIB_RD resets to 0, so the current logic works correctly there.
> > However, this assumption does not appear to hold for Versal.
>
> For Ultrascale+ the calibration register also gives random values after
> reset, perhaps you have noticed this:
> https://adaptivesupport.amd.com/s/article/000036886?language=en_US. Maybe
> the same can occur also on Versal.
>
> AFAIK there is no way of knowing if the value is correct or not after reset,
> so user space helpers might be needed to maintain the calibration value at a
> desired value.
>
Userspace is always needed to put the proper calibration, there is no
way for the kernel to know what value to put there. In the support case
above, the crystal will never be exactly 32768Hz and this value will
change over time and also depends on the temperature. The value always
needs to be computed, if your device can do NTP, chrony will provide the
proper offsets. If you don't have a way to measure the deviation, then
userspace can always forcefully set /sys/class/rtc/rtcX/offset if it
doesn't hold the correct value.
There is no need for devmem here.
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply
* Re: [QUESTION] rtc: zynqmp: CALIB_RD reset behavior differs between ZynqMP and Versal
From: Tomas Melin @ 2026-03-06 10:09 UTC (permalink / raw)
To: Takumi Ando, linux-rtc
Cc: alexandre.belloni, michal.simek, Yasushi SHOJI, kanta tamura
In-Reply-To: <CAJACUaoFK-GiBN_hfkNajDUygnSZc29U_jdeQ_rKtXS7P1f-nw@mail.gmail.com>
Hi,
On 05/03/2026 11:24, Takumi Ando wrote:
> [You don't often get email from takumi@spacecubics.com. Learn why this is important at https://aka.ms/LearnAboutSenderIdentification ]
>
> Hi,
>
> I have a question about the initialization logic in the zynqmp RTC
> driver(drivers/rtc/rtc-zynqmp.c).
>
> Currently the driver programs CALIB_WRITE only when CALIB_READ returns 0:
>
> ret = readl(... + RTC_CALIB_RD);
> if (!ret)
> writel(freq, ... + RTC_CALIB_WR);
>
> My understanding is that this was designed to avoid overwriting an
> existing calibration value. Since the RTC may continue running from the
> battery domain even when Linux is not running, the calibration value may
> have been configured previously and should be preserved.
>
> However, according to the Versal Adaptive SoC Register Reference (AM012) [1],
> the value returned by CALIB_RD after reset can be undefined.
> In practice, on Versal hardware we observe non-zero values even before
> any calibration has been programmed. Because of this, the current logic
> may skip programming CALIB_WR and leave the Max_Tick field uninitialized.
>
> On Zynq UltraScale+ Devices Register Reference (UG1087) [2],
> CALIB_RD resets to 0, so the current logic works correctly there.
> However, this assumption does not appear to hold for Versal.
For Ultrascale+ the calibration register also gives random values after
reset, perhaps you have noticed this:
https://adaptivesupport.amd.com/s/article/000036886?language=en_US.
Maybe the same can occur also on Versal.
AFAIK there is no way of knowing if the value is correct or not after
reset, so user space helpers might be needed to maintain the calibration
value at a desired value.
thanks,
Tomas
>
> If there is a register or mechanism that indicates whether the RTC has
> already been calibrated, the driver could use that instead. However,
> I could not find such an indicator in the documentation.
>
> Am I missing something here? Is there a recommended way to detect whether
> RTC calibration has already been configured?
>
> Alternatively, would it be acceptable for the driver to always program
> Max_Tick while preserving the fractional calibration bits already stored
> in hardware?
>
> Best regards,
>
> [1] https://docs.amd.com/r/en-US/am012-versal-register-reference/CALIB_READ-PMC_RTC-Register
> [2] https://docs.amd.com/r/en-US/ug1087-zynq-ultrascale-registers/CALIB_READ-RTC-Register
>
> --
> Takumi Ando
> Space Cubics Inc.
>
^ permalink raw reply
* Re: [PATCH v3 07/13] mfd: sec: set DMA coherent mask
From: André Draszik @ 2026-03-06 7:03 UTC (permalink / raw)
To: Kaustabh Chakraborty, Lee Jones, Pavel Machek, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, MyungJoo Ham, Chanwoo Choi,
Sebastian Reichel, Krzysztof Kozlowski, Alexandre Belloni,
Jonathan Corbet, Shuah Khan, Nam Tran
Cc: linux-leds, devicetree, linux-kernel, linux-pm, linux-samsung-soc,
linux-rtc, linux-doc
In-Reply-To: <20260225-s2mu005-pmic-v3-7-b4afee947603@disroot.org>
On Wed, 2026-02-25 at 00:45 +0530, Kaustabh Chakraborty wrote:
> Kernel logs are filled with "DMA mask not set" messages for every
> sub-device. The device does not use DMA for communication, so these
> messages are useless. Disable the coherent DMA mask for the PMIC device,
> which is also propagated to sub-devices.
>
> Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
> ---
> drivers/mfd/sec-i2c.c | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/drivers/mfd/sec-i2c.c b/drivers/mfd/sec-i2c.c
> index d8609886fcc80..9fa1449a4f6eb 100644
> --- a/drivers/mfd/sec-i2c.c
> +++ b/drivers/mfd/sec-i2c.c
> @@ -177,6 +177,9 @@ static int sec_pmic_i2c_probe(struct i2c_client *client)
> return dev_err_probe(&client->dev, PTR_ERR(regmap_pmic),
> "regmap init failed\n");
>
> + client->dev.coherent_dma_mask = 0;
> + client->dev.dma_mask = &client->dev.coherent_dma_mask;
> +
This should probably move into sec-common.c as it should apply to all
transports.
Cheers,
A.
^ permalink raw reply
* Re: [PATCH v3 04/13] dt-bindings: power: supply: document Samsung S2M series PMIC charger device
From: Rob Herring @ 2026-03-06 0:50 UTC (permalink / raw)
To: Kaustabh Chakraborty
Cc: Krzysztof Kozlowski, Lee Jones, Pavel Machek, Krzysztof Kozlowski,
Conor Dooley, MyungJoo Ham, Chanwoo Choi, Sebastian Reichel,
André Draszik, Alexandre Belloni, Jonathan Corbet,
Shuah Khan, Nam Tran, linux-leds, devicetree, linux-kernel,
linux-pm, linux-samsung-soc, linux-rtc, linux-doc
In-Reply-To: <DGPTBRX09EU5.1D1ZSR7EUV7AT@disroot.org>
On Fri, Feb 27, 2026 at 07:56:58PM +0530, Kaustabh Chakraborty wrote:
> On 2026-02-25 11:44 +01:00, Krzysztof Kozlowski wrote:
> > On Wed, Feb 25, 2026 at 12:45:06AM +0530, Kaustabh Chakraborty wrote:
> >> +
> >> + This is a part of device tree bindings for S2M and S5M family of Power
> >> + Management IC (PMIC).
> >> +
> >> + See also Documentation/devicetree/bindings/mfd/samsung,s2mps11.yaml for
> >> + additional information and example.
> >> +
> >> +allOf:
> >> + - $ref: power-supply.yaml#
> >> +
> >> +properties:
> >> + compatible:
> >> + enum:
> >> + - samsung,s2mu005-charger
> >
> > Review from v1 still applies. I think you ignored several reviews, so I
> > will mark entire patchset as changes requested.
>
> Somehow I missed this one... anyways I address them here:
>
> Why do you need a dedicated child node for this? It's got one property,
> other than the compatible, that you're using. It could easily just go
> in the parent without a dedicated node etc.
>
> The dt node also references a simple-battery node, that's why it's
> required.
That can go in the parent.
Rob
^ permalink raw reply
* Re: [PATCH 3/9] dt-bindings: input: mtk-pmic-keys: add MT6392 binding definition
From: Rob Herring (Arm) @ 2026-03-06 0:29 UTC (permalink / raw)
To: Luca Leonardo Scorcia
Cc: Louis-Alexis Eyraud, AngeloGioacchino Del Regno, linux-input,
Matthias Brugger, Sen Chu, Liam Girdwood, Sean Wang,
Alexandre Belloni, Julien Massot, linux-arm-kernel, Eddie Huang,
linux-kernel, Conor Dooley, Gary Bisson, Lee Jones,
Krzysztof Kozlowski, Fabien Parent, Val Packett, Macpaul Lin,
linux-rtc, devicetree, Dmitry Torokhov, linux-mediatek,
Mark Brown, linux-pm, Chen Zhong
In-Reply-To: <056cbc09fcbb4a2845cece69209a2a564d993ac5.1771865015.git.l.scorcia@gmail.com>
On Mon, 23 Feb 2026 17:12:42 +0000, Luca Leonardo Scorcia wrote:
> From: Fabien Parent <parent.f@gmail.com>
>
> Add the binding documentation of the mtk-pmic-keys for the MT6392 PMICs.
>
> Signed-off-by: Fabien Parent <parent.f@gmail.com>
> Signed-off-by: Val Packett <val@packett.cool>
> Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
> ---
> Documentation/devicetree/bindings/input/mediatek,pmic-keys.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
^ permalink raw reply
* Re: [PATCH 2/9] dt-bindings: regulator: add support for MT6392
From: Rob Herring (Arm) @ 2026-03-06 0:28 UTC (permalink / raw)
To: Luca Leonardo Scorcia
Cc: Mark Brown, Chen Zhong, Macpaul Lin, linux-pm,
Krzysztof Kozlowski, Lee Jones, linux-kernel, Dmitry Torokhov,
Louis-Alexis Eyraud, devicetree, linux-mediatek, Julien Massot,
Liam Girdwood, Alexandre Belloni, Fabien Parent, linux-input,
linux-rtc, Matthias Brugger, Val Packett, Sen Chu, Conor Dooley,
linux-arm-kernel, AngeloGioacchino Del Regno, Gary Bisson,
Eddie Huang, Sean Wang
In-Reply-To: <b7664f4d9a7b038b0603b6bba79cfab4e18cbdd6.1771865015.git.l.scorcia@gmail.com>
On Mon, 23 Feb 2026 17:12:41 +0000, Luca Leonardo Scorcia wrote:
> From: Fabien Parent <parent.f@gmail.com>
>
> Add binding documentation of the regulator for MT6392 SoCs.
>
> Signed-off-by: Fabien Parent <parent.f@gmail.com>
> Signed-off-by: Val Packett <val@packett.cool>
> Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
> ---
> Documentation/devicetree/bindings/mfd/mediatek,mt6397.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
^ permalink raw reply
* Re: [PATCH v2 1/2] dt-bindings: mfd: max77620: document optional RTC address for max77663
From: Rob Herring @ 2026-03-05 23:56 UTC (permalink / raw)
To: Svyatoslav Ryhel
Cc: Chanwoo Choi, Krzysztof Kozlowski, Lee Jones, Conor Dooley,
Alexandre Belloni, linux-kernel, devicetree, linux-rtc
In-Reply-To: <20260223064343.12516-2-clamor95@gmail.com>
On Mon, Feb 23, 2026 at 08:43:42AM +0200, Svyatoslav Ryhel wrote:
> Document an optional second I2C address for the MAX77663 PMIC's RTC
> device, to be used if the MAX77663 RTC is located at a non-default I2C
> address.
No changes to .txt bindings. Convert to schema first if you have
additions.
>
> Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
> ---
> Documentation/devicetree/bindings/mfd/max77620.txt | 4 +++-
> 1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt
> index 5a642a51d58e..0bbb42e5dcfe 100644
> --- a/Documentation/devicetree/bindings/mfd/max77620.txt
> +++ b/Documentation/devicetree/bindings/mfd/max77620.txt
> @@ -6,10 +6,12 @@ Required properties:
> "maxim,max77620"
> "maxim,max20024"
> "maxim,max77663"
> -- reg: I2C device address.
> +- reg: I2C device address. In case of MAX77663 there can be 2 addresses,
> + second one specifies position of RTC.
>
> Optional properties:
> -------------------
> +- reg-names: If 2 addresses are specified then, must be "pmic", "rtc"
> - interrupts: The interrupt on the parent the controller is
> connected to.
> - interrupt-controller: Marks the device node as an interrupt controller.
> --
> 2.51.0
>
^ permalink raw reply
* Re: [PATCH 3/6] regulator: dt-bindings: sc2731: Deprecate compatible property
From: Rob Herring (Arm) @ 2026-03-05 23:53 UTC (permalink / raw)
To: Otto Pflüger
Cc: linux-pm, Lee Jones, Liam Girdwood, Chunyan Zhang,
Krzysztof Kozlowski, Mark Brown, Conor Dooley, linux-kernel,
linux-rtc, Alexandre Belloni, Pavel Machek, Sebastian Reichel,
devicetree, Orson Zhai, Baolin Wang, linux-leds
In-Reply-To: <20260222-sc27xx-mfd-cells-v1-3-69526fe74c77@abscue.de>
On Sun, 22 Feb 2026 14:16:47 +0100, Otto Pflüger wrote:
> The node containing the regulators is always a child of the main PMIC
> node, which already has a compatible property identifying the type of
> PMIC. This makes the compatible in the child node redundant. Mark it
> as deprecated and remove it from the required property list and the
> examples.
>
> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
> ---
> Documentation/devicetree/bindings/mfd/sprd,sc2731.yaml | 2 --
> .../devicetree/bindings/regulator/sprd,sc2731-regulator.yaml | 4 +---
> 2 files changed, 1 insertion(+), 5 deletions(-)
>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
^ permalink raw reply
* Re: [PATCH 1/6] dt-bindings: rtc: sc2731: Add compatible for SC2730
From: Rob Herring (Arm) @ 2026-03-05 23:51 UTC (permalink / raw)
To: Otto Pflüger
Cc: Chunyan Zhang, devicetree, Krzysztof Kozlowski, Sebastian Reichel,
linux-leds, Lee Jones, Conor Dooley, Liam Girdwood, linux-rtc,
Mark Brown, Alexandre Belloni, Pavel Machek, linux-pm,
Baolin Wang, linux-kernel, Orson Zhai
In-Reply-To: <20260222-sc27xx-mfd-cells-v1-1-69526fe74c77@abscue.de>
On Sun, 22 Feb 2026 14:16:45 +0100, Otto Pflüger wrote:
> The RTC block found in the SC2730 PMIC is compatible with the one found
> in the SC2731 PMIC.
>
> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
> ---
> Documentation/devicetree/bindings/rtc/sprd,sc2731-rtc.yaml | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
^ permalink raw reply
* Re: [PATCH 2/6] dt-bindings: leds: sc2731: Add compatible for SC2730
From: Rob Herring (Arm) @ 2026-03-05 23:51 UTC (permalink / raw)
To: Otto Pflüger
Cc: Krzysztof Kozlowski, Chunyan Zhang, Sebastian Reichel, devicetree,
Alexandre Belloni, Orson Zhai, linux-kernel, Liam Girdwood,
Pavel Machek, Mark Brown, linux-rtc, linux-leds, Lee Jones,
Conor Dooley, linux-pm, Baolin Wang
In-Reply-To: <20260222-sc27xx-mfd-cells-v1-2-69526fe74c77@abscue.de>
On Sun, 22 Feb 2026 14:16:46 +0100, Otto Pflüger wrote:
> The LED controller found in the SC2730 PMIC is compatible with the one
> found in the SC2731 PMIC.
>
> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de>
> ---
> Documentation/devicetree/bindings/leds/sprd,sc2731-bltc.yaml | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
^ permalink raw reply
* Re: [PATCH v2 0/6] Remove use of i2c_match_id in RTC
From: Alexandre Belloni @ 2026-03-05 23:07 UTC (permalink / raw)
To: Andrew Davis; +Cc: linux-rtc, linux-kernel
In-Reply-To: <20260305193545.796294-1-afd@ti.com>
On 05/03/2026 13:35:39-0600, Andrew Davis wrote:
> Hello all,
>
> RTC subsystem is one of the last still using i2c_match_id().
> This is a v2 but nothing is changed from last time. If I'm
> not sending this to the right folks let me know.
Do you mean that you intend to remove i2c_match_id from the kernel?
>
> Thanks,
> Andrew
>
> Andrew Davis (6):
> rtc: abx80x: Remove use of i2c_match_id()
> rtc: m41t80: Remove use of i2c_match_id()
> rtc: pcf2127: Remove use of i2c_match_id()
> rtc: rs5c372: Remove use of i2c_match_id()
> rtc: rv8803: Remove use of i2c_match_id()
> rtc: rx8025: Remove use of i2c_match_id()
>
> drivers/rtc/rtc-abx80x.c | 3 +--
> drivers/rtc/rtc-m41t80.c | 8 +-------
> drivers/rtc/rtc-pcf2127.c | 23 +++++++----------------
> drivers/rtc/rtc-rs5c372.c | 7 +------
> drivers/rtc/rtc-rv8803.c | 8 +-------
> drivers/rtc/rtc-rx8025.c | 4 +---
> 6 files changed, 12 insertions(+), 41 deletions(-)
>
> --
> 2.39.2
>
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply
* [PATCH v2 4/6] rtc: rs5c372: Remove use of i2c_match_id()
From: Andrew Davis @ 2026-03-05 19:35 UTC (permalink / raw)
To: Alexandre Belloni; +Cc: linux-rtc, linux-kernel, Andrew Davis
In-Reply-To: <20260305193545.796294-1-afd@ti.com>
The function i2c_match_id() is used to fetch the matching ID from
the i2c_device_id table. This is often used to then retrieve the
matching driver_data. This can be done in one step with the helper
i2c_get_match_data().
This helper has a couple other benefits:
* It doesn't need the i2c_device_id passed in so we do not need
to have that forward declared, allowing us to remove those or
move the i2c_device_id table down to its more natural spot
with the other module info.
* It also checks for device match data, which allows for OF and
ACPI based probing. That means we do not have to manually check
those first and can remove those checks.
Signed-off-by: Andrew Davis <afd@ti.com>
---
drivers/rtc/rtc-rs5c372.c | 7 +------
1 file changed, 1 insertion(+), 6 deletions(-)
diff --git a/drivers/rtc/rtc-rs5c372.c b/drivers/rtc/rtc-rs5c372.c
index f8fab0205f8cc..936f4f05c8c7a 100644
--- a/drivers/rtc/rtc-rs5c372.c
+++ b/drivers/rtc/rtc-rs5c372.c
@@ -825,12 +825,7 @@ static int rs5c372_probe(struct i2c_client *client)
rs5c372->client = client;
i2c_set_clientdata(client, rs5c372);
- if (client->dev.of_node) {
- rs5c372->type = (uintptr_t)of_device_get_match_data(&client->dev);
- } else {
- const struct i2c_device_id *id = i2c_match_id(rs5c372_id, client);
- rs5c372->type = id->driver_data;
- }
+ rs5c372->type = (uintptr_t)i2c_get_match_data(client);
/* we read registers 0x0f then 0x00-0x0f; skip the first one */
rs5c372->regs = &rs5c372->buf[1];
--
2.39.2
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox