S3C HSOTG fixes

S3C HSOTG fixes

[Ben Dooks]

Repost of the series as requested by Greg. Fixes a number of problems
with the hsotg block on Samsung devices, including FIFO reset issues,
data sizes, dealing with core compilation options, et al.

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 02/11] USB: s3c-hsotg: The NPTX/PTX FIFO sizes are in words, not bytes

[Ben Dooks]

Fix a problem where we have been underestimating the space available in
the IN PTX/NPTX FIFOs by assuming that they where simply word aligned
instead of in number-of-words. This means all length calculations need
to be multiplied-by-4.

Note, we do not change the information about fifo size or start addresses
available to userspace as we assume the user can multiply by four easily
and is already knows these values are in words.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/usb/gadget/s3c-hsotg.c |    3 ++-
 1 files changed, 2 insertions(+), 1 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 81f62da..4a25145 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -505,6 +505,7 @@ static int s3c_hsotg_write_fifo(struct s3c_hsotg *hsotg,
 		}
 
 		can_write = S3C_GNPTXSTS_NPTxFSpcAvail_GET(gnptxsts);
+		can_write *= 4;	/* fifo size is in 32bit quantities. */
 	}
 
 	dev_dbg(hsotg->dev, "%s: GNPTXSTS=%08x, can=%d, to=%d, mps %d\n",
@@ -2732,7 +2733,7 @@ static void __devinit s3c_hsotg_initep(struct s3c_hsotg *hsotg,
 	 */
 
 	ptxfifo = readl(hsotg->regs + S3C_DPTXFSIZn(epnum));
-	hs_ep->fifo_size = S3C_DPTXFSIZn_DPTxFSize_GET(ptxfifo);
+	hs_ep->fifo_size = S3C_DPTXFSIZn_DPTxFSize_GET(ptxfifo) * 4;
 
 	/* if we're using dma, we need to set the next-endpoint pointer
 	 * to be something valid.
-- 
1.7.0.4

[PATCH 01/11] USB: s3c-hsotg: Increase TX fifo limit

[Ben Dooks]

Up the FIFO size for the TX to 1024 entries, as this now seems to work
with all the cores. This fixes a problem when using large packets on
a core with MPS set to 512 can hang due to insufficient space for the
writes.

The hang arises due to getting the non-periodic FIFO empty IRQ but
not being able to satisfy any requests since there is never enough
space to write 512 bytes into the buffer. This means we end up with
a stream of interrupt requests.

It is easier to up the TX FIFO to fill the space we left for it
than to try and fix the positions in the code where we should have
limited the max-packet size to < TXFIFOSIZE, since the TXFIFOSIZE
depends on how the TX FIFOs have been setup.

Signed-off-by: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
---
 drivers/usb/gadget/s3c-hsotg.c |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 26193ec..81f62da 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -310,11 +310,11 @@ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg)
 		hsotg->regs + S3C_GNPTXFSIZ);
 	*/
 
-	/* set FIFO sizes to 2048/0x1C0 */
+	/* set FIFO sizes to 2048/1024 */
 
 	writel(2048, hsotg->regs + S3C_GRXFSIZ);
 	writel(S3C_GNPTXFSIZ_NPTxFStAddr(2048) |
-	       S3C_GNPTXFSIZ_NPTxFDep(0x1C0),
+	       S3C_GNPTXFSIZ_NPTxFDep(1024),
 	       hsotg->regs + S3C_GNPTXFSIZ);
 
 	/* arange all the rest of the TX FIFOs, as some versions of this
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 03/11] USB: s3c-hsotg: Avoid overwriting contents of perodic in 'fifo'

[Ben Dooks]

In shared fifo mode (used on older SoCs) the periodic in fifo beahves
much more like a packet buffer, discarding old data when writing new
data. Avoid this by ensuring that we do not load new transactions in
when there is data sitting already in the FIFO.

Note, this may not be an observed bug, we are fixing the case that this
may happen.

Signed-off-by: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
---
 drivers/usb/gadget/s3c-hsotg.c |   12 +++++++++++-
 1 files changed, 11 insertions(+), 1 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 4a25145..354fd45 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -91,7 +91,9 @@ struct s3c_hsotg_req;
  * For periodic IN endpoints, we have fifo_size and fifo_load to try
  * and keep track of the amount of data in the periodic FIFO for each
  * of these as we don't have a status register that tells us how much
- * is in each of them.
+ * is in each of them. (note, this may actually be useless information
+ * as in shared-fifo mode periodic in acts like a single-frame packet
+ * buffer than a fifo)
  */
 struct s3c_hsotg_ep {
 	struct usb_ep		ep;
@@ -474,6 +476,14 @@ static int s3c_hsotg_write_fifo(struct s3c_hsotg *hsotg,
 
 		size_left = S3C_DxEPTSIZ_XferSize_GET(epsize);
 
+		/* if shared fifo, we cannot write anything until the
+		 * previous data has been completely sent.
+		 */
+		if (hs_ep->fifo_load != 0) {
+			s3c_hsotg_en_gsint(hsotg, S3C_GINTSTS_PTxFEmp);
+			return -ENOSPC;
+		}
+
 		dev_dbg(hsotg->dev, "%s: left=%d, load=%d, fifo=%d, size %d\n",
 			__func__, size_left,
 			hs_ep->size_loaded, hs_ep->fifo_load, hs_ep->fifo_size);
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 04/11] USB: s3c-hsotg: Re-initialise all FIFOs on USB bus reset

[Ben Dooks]

The USB documentation suggest that the FIFOs should be reset when a
bus reset event happens. Use the s3c_hsotg_init_fifo() to ensure that
the FIFO layout is correct and that the FIFOs are flushed before
acknowledging the reset.

Signed-off-by: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
---
 drivers/usb/gadget/s3c-hsotg.c |   13 ++++---------
 1 files changed, 4 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 354fd45..9d32c9f 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -2082,17 +2082,12 @@ irq_retry:
 		kill_all_requests(hsotg, &hsotg->eps[0], -ECONNRESET, true);
 
 		/* it seems after a reset we can end up with a situation
-		 * where the TXFIFO still has data in it... try flushing
-		 * it to remove anything that may still be in it.
+		 * where the TXFIFO still has data in it... the docs
+		 * suggest resetting all the fifos, so use the init_fifo
+		 * code to relayout and flush the fifos.
 		 */
 
-		if (1) {
-			writel(S3C_GRSTCTL_TxFNum(0) | S3C_GRSTCTL_TxFFlsh,
-			       hsotg->regs + S3C_GRSTCTL);

[PATCH 06/11] USB: s3c-hsotg: Only load packet per fifo write

[Ben Dooks]

Limit the IN FIFO write to a single packet per attempt at writing,
as per the specifications and ensure that we don't return fifo-full
so that we can continue writing packets if we have the space.

Signed-off-by: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
---
 drivers/usb/gadget/s3c-hsotg.c |   11 +++++++++++
 1 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 4196e37..df6a39d 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -538,6 +538,17 @@ static int s3c_hsotg_write_fifo(struct s3c_hsotg *hsotg,
 	if (can_write > 512)
 		can_write = 512;
 
+	/* limit the write to one max-packet size worth of data, but allow
+	 * the transfer to return that it did not run out of fifo space
+	 * doing it. */
+	if (to_write > hs_ep->ep.maxpacket) {
+		to_write = hs_ep->ep.maxpacket;
+
+		s3c_hsotg_en_gsint(hsotg,
+				   periodic ? S3C_GINTSTS_PTxFEmp :
+				   S3C_GINTSTS_NPTxFEmp);
+	}
+
 	/* see if we can write data */
 
 	if (to_write > can_write) {
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 08/11] USB: s3c-hsotg: Fix max EP0 IN request length

[Ben Dooks]

The maximum length for any EP0 IN request on EP0 is 127 bytes, not 128
as the driver currently has it.

Signed-off-by: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
---
 drivers/usb/gadget/s3c-hsotg.c |    3 +--
 1 files changed, 1 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 10aeee1..1020006 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -612,8 +612,7 @@ static unsigned get_ep_limit(struct s3c_hsotg_ep *hs_ep)
 		maxpkt = S3C_DxEPTSIZ_PktCnt_LIMIT + 1;
 	} else {
 		if (hs_ep->dir_in) {
-			/* maxsize = S3C_DIEPTSIZ0_XferSize_LIMIT + 1; */
-			maxsize = 64+64+1;
+			maxsize = 64+64;
 			maxpkt = S3C_DIEPTSIZ0_PktCnt_LIMIT + 1;
 		} else {
 			maxsize = 0x3f;
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 10/11] USB: s3c-hsotg: Fix OUT packet request retry

[Ben Dooks]

If there is more data in the request than we could fit into a single
hardware request, then check when the OutDone event is received if
we have more data, and if so, schedule the new data instead of trying
to complete the request (and in the case of EP0, sending a 0 packet
in the middle of a transfer).

Also, move the debug message about the current transfer state before
the warning about a bad transfer.

Signed-off-by: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
---
 drivers/usb/gadget/s3c-hsotg.c |   18 +++++++++++-------
 1 files changed, 11 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 552ec89..825b6ca 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -1383,6 +1383,9 @@ static void s3c_hsotg_rx_data(struct s3c_hsotg *hsotg, int ep_idx, int size)
 	read_ptr = hs_req->req.actual;
 	max_req = hs_req->req.length - read_ptr;
 
+	dev_dbg(hsotg->dev, "%s: read %d/%d, done %d/%d\n",
+		__func__, to_read, max_req, read_ptr, hs_req->req.length);
+
 	if (to_read > max_req) {
 		/* more data appeared than we where willing
 		 * to deal with in this request.
@@ -1392,9 +1395,6 @@ static void s3c_hsotg_rx_data(struct s3c_hsotg *hsotg, int ep_idx, int size)
 		WARN_ON_ONCE(1);
 	}
 
-	dev_dbg(hsotg->dev, "%s: read %d/%d, done %d/%d\n",
-		__func__, to_read, max_req, read_ptr, hs_req->req.length);
-
 	hs_ep->total_data += to_read;
 	hs_req->req.actual += to_read;
 	to_read = DIV_ROUND_UP(to_read, 4);
@@ -1463,9 +1463,11 @@ static void s3c_hsotg_send_zlp(struct s3c_hsotg *hsotg,
 static void s3c_hsotg_handle_outdone(struct s3c_hsotg *hsotg,
 				     int epnum, bool was_setup)
 {
+	u32 epsize = readl(hsotg->regs + S3C_DOEPTSIZ(epnum));
 	struct s3c_hsotg_ep *hs_ep = &hsotg->eps[epnum];
 	struct s3c_hsotg_req *hs_req = hs_ep->req;
 	struct usb_request *req = &hs_req->req;
+	unsigned size_left = S3C_DxEPTSIZ_XferSize_GET(epsize);
 	int result = 0;
 
 	if (!hs_req) {
@@ -1474,9 +1476,7 @@ static void s3c_hsotg_handle_outdone(struct s3c_hsotg *hsotg,
 	}
 
 	if (using_dma(hsotg)) {
-		u32 epsize = readl(hsotg->regs + S3C_DOEPTSIZ(epnum));
 		unsigned size_done;
-		unsigned size_left;
 
 		/* Calculate the size of the transfer by checking how much
 		 * is left in the endpoint size register and then working it
@@ -1486,14 +1486,18 @@ static void s3c_hsotg_handle_outdone(struct s3c_hsotg *hsotg,
 		 * so may overshoot/undershoot the transfer.
 		 */
 
-		size_left = S3C_DxEPTSIZ_XferSize_GET(epsize);

[PATCH 11/11] USB: s3c-hsotg: Add support for external USB clock

[Ben Dooks]

From: Maurus Cuelenaere <mcuelenaere-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

The PLL that drives the USB clock supports 3 input clocks: 12, 24 and 48Mhz.
This patch adds support to the USB driver for setting the correct register bit
according to the given clock.

This depends on the following patch:
[PATCH] ARM: S3C64XX: Add USB external clock definition

Signed-off-by: Maurus Cuelenaere <mcuelenaere-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Signed-off-by: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
---
 drivers/usb/gadget/s3c-hsotg.c |   19 +++++++++++++++++++
 1 files changed, 19 insertions(+), 0 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 825b6ca..a4e0b0f 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -25,6 +25,7 @@
 #include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/slab.h>
+#include <linux/clk.h>
 
 #include <linux/usb/ch9.h>
 #include <linux/usb/gadget.h>
@@ -2798,6 +2799,7 @@ static void __devinit s3c_hsotg_initep(struct s3c_hsotg *hsotg,
  */
 static void s3c_hsotg_otgreset(struct s3c_hsotg *hsotg)
 {
+	struct clk *xusbxti;
 	u32 osc;
 
 	writel(0, S3C_PHYPWR);
@@ -2805,6 +2807,23 @@ static void s3c_hsotg_otgreset(struct s3c_hsotg *hsotg)
 
 	osc = hsotg->plat->is_osc ? S3C_PHYCLK_EXT_OSC : 0;
 
+	xusbxti = clk_get(hsotg->dev, "xusbxti");
+	if (xusbxti && !IS_ERR(xusbxti)) {
+		switch (clk_get_rate(xusbxti)) {
+		case 12*MHZ:
+			osc |= S3C_PHYCLK_CLKSEL_12M;
+			break;
+		case 24*MHZ:
+			osc |= S3C_PHYCLK_CLKSEL_24M;
+			break;
+		default:
+		case 48*MHZ:
+			/* default reference clock */
+			break;
+		}
+		clk_put(xusbxti);
+	}
+
 	writel(osc | 0x10, S3C_PHYCLK);
 
 	/* issue a full set of resets to the otg and core */
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 05/11] USB: s3c-hsotg: Add initial detection and setup for dedicated FIFO mode

[Ben Dooks]

Add support for the dedicated FIFO mode on newer SoCs such as the S5PV210
partly to improve support and to fix the bug where any non-EP0 IN endpoint
requires its own FIFO allocation.

To fix this, we ensure that any non-zero IN endpoint is given a TXFIFO
using the same allocation method as the periodic case (all our current
hardware has enough FIFOs and FIFO memory for a 1:1 mapping) and ensure
that the necessary transmission done interrupt is enabled.

The default settings from reset for the core point all EPs at FIFO0,
used for the control endpoint. However, the controller documentation
states that all IN endpoints _must_ have a unique FIFO to avoid any
contention during transmission.

Note, this leaves us with a large IN FIFO for EP0 (which re-uses the
old NPTXFIFO) for an endpoint which cannot shift more than a pair of
packets at a time... this is a waste, but it looks like we cannot
re-allocate space to the individual IN FIFOs as they are already
maxed out (to be confirmed).

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 .../arm/plat-samsung/include/plat/regs-usb-hsotg.h |    2 +
 drivers/usb/gadget/s3c-hsotg.c                     |   40 +++++++++++++++++++-
 2 files changed, 40 insertions(+), 2 deletions(-)

diff --git a/arch/arm/plat-samsung/include/plat/regs-usb-hsotg.h b/arch/arm/plat-samsung/include/plat/regs-usb-hsotg.h
index 8d18d9d..dc90f5e 100644
--- a/arch/arm/plat-samsung/include/plat/regs-usb-hsotg.h
+++ b/arch/arm/plat-samsung/include/plat/regs-usb-hsotg.h
@@ -226,6 +226,7 @@
 
 #define S3C_DIEPMSK				S3C_HSOTG_REG(0x810)
 
+#define S3C_DIEPMSK_TxFIFOEmpty			(1 << 7)
 #define S3C_DIEPMSK_INEPNakEffMsk		(1 << 6)
 #define S3C_DIEPMSK_INTknEPMisMsk		(1 << 5)
 #define S3C_DIEPMSK_INTknTXFEmpMsk		(1 << 4)
@@ -371,6 +372,7 @@
 
 #define S3C_DIEPDMA(_a)				S3C_HSOTG_REG(0x914 + ((_a) * 0x20))
 #define S3C_DOEPDMA(_a)				S3C_HSOTG_REG(0xB14 + ((_a) * 0x20))
+#define S3C_DTXFSTS(_a)				S3C_HSOTG_REG(0x918 + ((_a) * 0x20))
 
 #define S3C_EPFIFO(_a)				S3C_HSOTG_REG(0x1000 + ((_a) * 0x1000))
 
diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 9d32c9f..4196e37 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -12,6 +12,8 @@
  * published by the Free Software Foundation.
 */
 
+#define DEBUG
+
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/spinlock.h>
@@ -130,6 +132,7 @@ struct s3c_hsotg_ep {
  * @regs: The memory area mapped for accessing registers.
  * @regs_res: The resource that was allocated when claiming register space.
  * @irq: The IRQ number we are using
+ * @dedicated_fifos: Set if the hardware has dedicated IN-EP fifos.
  * @debug_root: root directrory for debugfs.
  * @debug_file: main status file for debugfs.
  * @debug_fifo: FIFO status file for debugfs.
@@ -148,6 +151,8 @@ struct s3c_hsotg {
 	struct resource		*regs_res;
 	int			irq;
 
+	unsigned int		dedicated_fifos:1;
+
 	struct dentry		*debug_root;
 	struct dentry		*debug_file;
 	struct dentry		*debug_fifo;
@@ -466,7 +471,7 @@ static int s3c_hsotg_write_fifo(struct s3c_hsotg *hsotg,
 	if (to_write == 0)
 		return 0;
 
-	if (periodic) {
+	if (periodic && !hsotg->dedicated_fifos) {
 		u32 epsize = readl(hsotg->regs + S3C_DIEPTSIZ(hs_ep->index));
 		int size_left;
 		int size_done;
@@ -504,6 +509,11 @@ static int s3c_hsotg_write_fifo(struct s3c_hsotg *hsotg,
 			s3c_hsotg_en_gsint(hsotg, S3C_GINTSTS_PTxFEmp);
 			return -ENOSPC;
 		}
+	} else if (hsotg->dedicated_fifos && hs_ep->index != 0) {
+		can_write = readl(hsotg->regs + S3C_DTXFSTS(hs_ep->index));
+
+		can_write &= 0xffff;
+		can_write *= 4;
 	} else {
 		if (S3C_GNPTXSTS_NPTxQSpcAvail_GET(gnptxsts) == 0) {
 			dev_dbg(hsotg->dev,
@@ -1829,6 +1839,15 @@ static void s3c_hsotg_epint(struct s3c_hsotg *hsotg, unsigned int idx,
 				 __func__, idx);
 			clear |= S3C_DIEPMSK_INTknEPMisMsk;
 		}
+
+		/* FIFO has space or is empty (see GAHBCFG) */
+		if (hsotg->dedicated_fifos &&
+		    ints & S3C_DIEPMSK_TxFIFOEmpty) {
+			dev_dbg(hsotg->dev, "%s: ep%d: TxFIFOEmpty\n",
+				__func__, idx);
+			s3c_hsotg_trytx(hsotg, hs_ep);
+			clear |= S3C_DIEPMSK_TxFIFOEmpty;
+		}
 	}
 
 	writel(clear, hsotg->regs + epint_reg);
@@ -2280,6 +2299,12 @@ static int s3c_hsotg_ep_enable(struct usb_ep *ep,
 		break;
 	}
 
+	/* if the hardware has dedicated fifos, we must give each IN EP
+	 * a unique tx-fifo even if it is non-periodic.
+	 */
+	if (dir_in && hsotg->dedicated_fifos)
+		epctrl |= S3C_DxEPCTL_TxFNum(index);
+
 	/* for non control endpoints, set PID to D0 */
 	if (index)
 		epctrl |= S3C_DxEPCTL_SetD0PID;
@@ -2569,7 +2594,8 @@ int usb_gadget_register_driver(struct usb_gadget_driver *driver)
 
 	writel(S3C_DIEPMSK_TimeOUTMsk | S3C_DIEPMSK_AHBErrMsk |
 	       S3C_DIEPMSK_INTknEPMisMsk |
-	       S3C_DIEPMSK_EPDisbldMsk | S3C_DIEPMSK_XferComplMsk,
+	       S3C_DIEPMSK_EPDisbldMsk | S3C_DIEPMSK_XferComplMsk |
+	       ((hsotg->dedicated_fifos) ? S3C_DIEPMSK_TxFIFOEmpty : 0),
 	       hsotg->regs + S3C_DIEPMSK);
 
 	/* don't need XferCompl, we get that from RXFIFO in slave mode. In
@@ -2778,6 +2804,8 @@ static void s3c_hsotg_otgreset(struct s3c_hsotg *hsotg)
 
 static void s3c_hsotg_init(struct s3c_hsotg *hsotg)
 {
+	u32 cfg4;
+
 	/* unmask subset of endpoint interrupts */
 
 	writel(S3C_DIEPMSK_TimeOUTMsk | S3C_DIEPMSK_AHBErrMsk |
@@ -2813,6 +2841,14 @@ static void s3c_hsotg_init(struct s3c_hsotg *hsotg)
 
 	writel(using_dma(hsotg) ? S3C_GAHBCFG_DMAEn : 0x0,
 	       hsotg->regs + S3C_GAHBCFG);
+
+	/* check hardware configuration */
+
+	cfg4 = readl(hsotg->regs + 0x50);
+	hsotg->dedicated_fifos = (cfg4 >> 25) & 1;
+
+	dev_info(hsotg->dev, "%s fifos\n",
+		 hsotg->dedicated_fifos ? "dedicated" : "shared");
 }
 
 static void s3c_hsotg_dump(struct s3c_hsotg *hsotg)
-- 
1.7.0.4

[PATCH 07/11] USB: s3c-hsotg: Check for new request before enqueing new setup

[Ben Dooks]

Before trying a new setup transaction after getting an EP0 in complete
interrupt, check that the driver did not try and send more EP0 IN data
before enqueing a new setup transaction.

This fixes a bug where we cannot send all of the IN data in one go
so split the transfer, but then fail to send all the data as we start
waiting for a new OUT transaction

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/usb/gadget/s3c-hsotg.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index df6a39d..10aeee1 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -1790,7 +1790,7 @@ static void s3c_hsotg_epint(struct s3c_hsotg *hsotg, unsigned int idx,
 		if (dir_in) {
 			s3c_hsotg_complete_in(hsotg, hs_ep);
 
-			if (idx == 0)
+			if (idx == 0 && !hs_ep->req)
 				s3c_hsotg_enqueue_setup(hsotg);
 		} else if (using_dma(hsotg)) {
 			/* We're using DMA, we need to fire an OutDone here
-- 
1.7.0.4

[PATCH 09/11] USB: s3c-hsotg: Fix the OUT EP0 limit

[Ben Dooks]

The EP0 out limit is the same as the IN limit, so make them the same.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
---
 drivers/usb/gadget/s3c-hsotg.c |    3 +--
 1 files changed, 1 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/gadget/s3c-hsotg.c b/drivers/usb/gadget/s3c-hsotg.c
index 1020006..552ec89 100644
--- a/drivers/usb/gadget/s3c-hsotg.c
+++ b/drivers/usb/gadget/s3c-hsotg.c
@@ -611,11 +611,10 @@ static unsigned get_ep_limit(struct s3c_hsotg_ep *hs_ep)
 		maxsize = S3C_DxEPTSIZ_XferSize_LIMIT + 1;
 		maxpkt = S3C_DxEPTSIZ_PktCnt_LIMIT + 1;
 	} else {
+		maxsize = 64+64;
 		if (hs_ep->dir_in) {
-			maxsize = 64+64;
 			maxpkt = S3C_DIEPTSIZ0_PktCnt_LIMIT + 1;
 		} else {
-			maxsize = 0x3f;
 			maxpkt = 2;
 		}
 	}
-- 
1.7.0.4