From: bugme-daemon@bugzilla.kernel.org
To: linux-scsi@vger.kernel.org
Subject: [Bug 12120] [Block layer or SCSI] requests aborted too early during check_partition()
Date: Sat, 29 Nov 2008 11:29:55 -0800 (PST) [thread overview]
Message-ID: <20081129192955.3C53F10800F@picon.linux-foundation.org> (raw)
In-Reply-To: <bug-12120-11613@http.bugzilla.kernel.org/>
http://bugzilla.kernel.org/show_bug.cgi?id=12120
------- Comment #3 from anonymous@kernel-bugs.osdl.org 2008-11-29 11:29 -------
Reply-To: stefanr@s5r6.in-berlin.de
> It sounds like the device isn't being spun up, so commands which require
> media read are being failed with not ready. Could we get some traces to
> show this; just enable all tracing in the boot up sequence:
>
> echo 0xffffffff > /sys/module/scsi_mod/parameters/scsi_logging_level
OK, here is a log from a failing session in 2.6.28-rc6.
The firmware responds to everything without spinning the disk up,
until the first READ(10) is sent.
# spin disk down artificially with
# "modprobe -r firewire-sbp2" while manage_start_stop == 1
#
# then "modprobe firewire-sbp2"
Nov 29 19:57:05 stein Error handler scsi_eh_20 sleeping
Nov 29 19:57:05 stein scsi20 : SBP-2 IEEE-1394
Nov 29 19:57:06 stein firewire_sbp2: fw3.0: logged in to LUN 0000 (0 retries)
Nov 29 19:57:06 stein scsi 20:0:0:0: scsi scan: INQUIRY pass 1 length 36
Nov 29 19:57:06 stein scsi 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein scsi 20:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 36, queuecommand
0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein scsi 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein scsi 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein scsi 20:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
Nov 29 19:57:06 stein scsi 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein scsi 20:0:0:0: Notifying upper driver of completion
(result 0)
Nov 29 19:57:06 stein 0 sectors total, 36 bytes done.
Nov 29 19:57:06 stein scsi scan: INQUIRY successful with code 0x0
Nov 29 19:57:06 stein scsi 20:0:0:0: Direct-Access-RBC ST340083 2A
3.03 PQ: 0 ANSI: 4
Nov 29 19:57:06 stein sd 20:0:0:0: sd_attach
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_revalidate_disk
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
Nov 29 19:57:06 stein buffer = 0x00000000, bufflen = 0, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 0 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Read Capacity(10): 25 00 00 00 00 00 00
00 00 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 8, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Read Capacity(10): 25 00 00 00 00 00 00
00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 8 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] 781422768 512-byte hardware sectors:
(400 GB/372 GiB)
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 00 3f 00 04 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 4, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 00 3f 00 04 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 4 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Write Protect is off
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Mode Sense: 11 00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 04 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 4, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 04 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 4 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 16 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 22, queuecommand
0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 16 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 22 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_open
Nov 29 19:57:06 stein scsi_block_when_processing_errors: rtn: 1
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_revalidate_disk
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57984a0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
Nov 29 19:57:06 stein buffer = 0x00000000, bufflen = 0, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57984a0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 0 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf5798550
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Read Capacity(10): 25 00 00 00 00 00 00
00 00 00
Nov 29 19:57:06 stein buffer = 0xf725fd68, bufflen = 8, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf5798550 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Read Capacity(10): 25 00 00 00 00 00 00
00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 8 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] 781422768 512-byte hardware sectors:
(400 GB/372 GiB)
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57981e0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 00 3f 00 04 00
Nov 29 19:57:06 stein buffer = 0xf725fed8, bufflen = 4, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57981e0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 00 3f 00 04 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 4 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Write Protect is off
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Mode Sense: 11 00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf5798600
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 04 00
Nov 29 19:57:06 stein buffer = 0xf725f918, bufflen = 4, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf5798600 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 04 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 4 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf5798ef0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 16 00
Nov 29 19:57:06 stein buffer = 0xe5961b40, bufflen = 22, queuecommand
0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf5798ef0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 16 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 22 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
# partition scanning code gets into gears,
# issues very first READ command,
# now the failures start
Nov 29 19:57:06 stein sdd:<6>sd 20:0:0:0: [sdd] sd_init_command: block=0,
count=8
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] block=0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] reading 8/8 512 byte blocks.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Send: 0xf5798ef0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] CDB: Read(10): 28 00 00 00 00 00 00 00
08 00
Nov 29 19:57:06 stein buffer = 0xe5961b40, bufflen = 4096, queuecommand
0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Done: 0xf5798ef0 FAILED
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] CDB: Read(10): 28 00 00 00 00 00 00 00
08 00
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Sense Key : Not Ready [current]
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Add. Sense: Logical unit not ready,
initializing command required
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] scsi host busy 1 failed 0
Nov 29 19:57:06 stein Waking error handler thread
Nov 29 19:57:06 stein Error handler scsi_eh_20 waking up
Nov 29 19:57:06 stein sd 20:0:0:0: scsi_eh_prt_fail_stats: cmds failed: 1,
cancel: 0
Nov 29 19:57:06 stein Total of 1 commands on 1 devices require eh work
Nov 29 19:57:06 stein scsi_eh_20: Sending START_UNIT to sdev: 0xe58fc7f0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Send: 0xf5798ef0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] CDB: Start/Stop Unit: 1b 00 00 00 01
00
Nov 29 19:57:06 stein buffer = 0x00000000, bufflen = 0, queuecommand 0xf85fb980
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Done: 0xf5798ef0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] CDB: Start/Stop Unit: 1b 00 00 00 01
00
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Unrecognized sense data (in hex):
Nov 29 19:57:06 stein 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Nov 29 19:57:06 stein 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Nov 29 19:57:06 stein Sense Key : No Sense [current]
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Add. Sense: No additional sense
information
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] scsi host busy 1 failed 1
Nov 29 19:57:06 stein scsi_send_eh_cmnd: scmd: f5798ef0, timeleft: 0
Nov 29 19:57:06 stein firewire_sbp2: fw3.0: sbp2_scsi_abort
Nov 29 19:57:06 stein scsi_eh_done scmd: f5798ef0 result: 20000
Nov 29 19:57:06 stein scsi_eh_20: START_UNIT failed to sdev: 0xe58fc7f0
Nov 29 19:57:06 stein scsi_eh_20: Sending BDR sdev: 0xe58fc7f0
Nov 29 19:57:06 stein scsi_eh_20: BDR failed sdev:0xe58fc7f0
Nov 29 19:57:06 stein scsi_eh_20: Sending target reset to target 0
Nov 29 19:57:06 stein scsi_eh_20: Target reset failed target: 0
Nov 29 19:57:06 stein scsi_eh_20: Sending BRST chan: 0
Nov 29 19:57:06 stein scsi_try_bus_reset: Snd Bus RST
Nov 29 19:57:06 stein scsi_eh_20: BRST failed chan: 0
Nov 29 19:57:06 stein scsi_eh_20: Sending HRST
Nov 29 19:57:06 stein scsi_try_host_reset: Snd Host RST
Nov 29 19:57:06 stein scsi_eh_20: HRST failed
Nov 29 19:57:06 stein sd 20:0:0:0: Device offlined - not ready after error
recovery
Nov 29 19:57:06 stein scsi_eh_20: flush finish cmd: f5798ef0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
2)
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein 8 sectors total, 0 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein end_request: I/O error, dev sdd, sector 0
Nov 29 19:57:06 stein Buffer I/O error on device sdd, logical block 0
Nov 29 19:57:06 stein scsi_restart_operations: waking up host to restart
Nov 29 19:57:06 stein Error handler scsi_eh_20 sleeping
Nov 29 19:57:06 stein sd 20:0:0:0: rejecting I/O to offline device
Nov 29 19:57:06 stein Buffer I/O error on device sdd, logical block 0
Nov 29 19:57:06 stein ldm_validate_partition_table(): Disk read failed.
Nov 29 19:57:06 stein sd 20:0:0:0: rejecting I/O to offline device
Nov 29 19:57:06 stein Buffer I/O error on device sdd, logical block 0
Nov 29 19:57:06 stein sd 20:0:0:0: rejecting I/O to offline device
Nov 29 19:57:06 stein Buffer I/O error on device sdd, logical block 0
Nov 29 19:57:06 stein unable to read partition table
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_release
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Attached SCSI disk
Nov 29 19:57:06 stein sg_alloc: dev=3
Nov 29 19:57:06 stein sd 20:0:0:0: Attached scsi generic sg3 type 14
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_open
Nov 29 19:57:06 stein scsi_block_when_processing_errors: rtn: 0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_open
Nov 29 19:57:06 stein scsi_block_when_processing_errors: rtn: 0
Nov 29 19:57:08 stein firewire_sbp2: fw3.0: reconnected to LUN 0000 (0 retries)
Nov 29 19:57:14 stein firewire_sbp2: fw3.0: reconnected to LUN 0000 (0 retries)
Nov 29 19:58:09 stein xinetd[4299]: START: imap2 pid=18913 from=192.168.0.42
Nov 29 19:58:09 stein imapd[18913]: imap service init from 192.168.0.42
Nov 29 19:58:09 stein imapd[18913]: Login user=stefan host=stein [192.168.0.42]
Nov 29 19:58:15 stein imapd[18914]: imap service init from 192.168.0.42
Nov 29 19:58:15 stein xinetd[4299]: START: imap2 pid=18914 from=192.168.0.42
Nov 29 19:58:15 stein imapd[18914]: Login user=stefan host=stein [192.168.0.42]
Nov 29 19:58:19 stein imapd[18913]: Logout user=stefan host=stein
[192.168.0.42]
Nov 29 19:58:19 stein xinetd[4299]: EXIT: imap2 status=0 pid=18913
duration=10(sec)
Nov 29 19:59:07 stein imapd[18914]: Logout user=stefan host=stein
[192.168.0.42]
Nov 29 19:59:07 stein xinetd[4299]: EXIT: imap2 status=0 pid=18914
duration=52(sec)
--
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.
next prev parent reply other threads:[~2008-11-29 19:30 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-11-29 13:19 [Bug 12120] New: [Block layer or SCSI] requests aborted too early during check_partition() bugme-daemon
2008-11-29 15:12 ` Stefan Richter
2008-11-29 18:35 ` James Bottomley
2008-11-29 15:12 ` [Bug 12120] " bugme-daemon
2008-11-29 18:36 ` bugme-daemon
2008-11-29 19:29 ` bugme-daemon [this message]
2008-11-29 19:32 ` bugme-daemon
2008-11-29 19:54 ` James Bottomley
2008-11-29 21:30 ` Stefan Richter
2008-11-29 21:45 ` Stefan Richter
2008-11-30 0:08 ` James Bottomley
2008-11-30 9:44 ` Stefan Richter
2008-11-30 16:16 ` James Bottomley
2008-11-29 19:55 ` bugme-daemon
2008-11-29 21:30 ` bugme-daemon
2008-11-29 21:45 ` bugme-daemon
2008-11-30 0:08 ` bugme-daemon
2008-11-30 9:44 ` bugme-daemon
2008-11-30 16:16 ` bugme-daemon
2008-12-04 1:15 ` bugme-daemon
2008-12-04 6:38 ` bugme-daemon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20081129192955.3C53F10800F@picon.linux-foundation.org \
--to=bugme-daemon@bugzilla.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox