Re: qla1280 driver for qlogic-1040 on alpha

[Thomas Bogendoerfer <tbogendoerfer@suse.de>]

On Tue, 5 Nov 2024 20:24:58 +0100
Magnus Lindholm <linmag7@gmail.com> wrote:

> >  Thomas, Magnus, can you please check what hardware revision is actually
> > reported by your devices?  Also a dump of the PCI configuration space
> > would be very useful, or at the very least the value of the PCI Revision
> > ID register, which is independent from the hardware revision reported via
> > the device I/O registers.  
> 
> Below is some info from my Alpha ES40 with an ISP1040. I've added a
> printout of hardware revision number to the driver, as previously
> pointed out the revision numbers in qla1280.h is wrong so I've used
> info from NetBSD
> rev5 is a "B" which matches what is actually printed on the chip as
> well. This seems to be consistent with PCI Revision ID register.
> 
> output from driver:
> 
> qla1280: QLA1040 found on PCI bus 2, dev 4
> revision=5 <-- printout of cfg0 register 5 = rev B
> QLogic QLA1040 PCI to SCSI Host Adapter
> Firmware version:  7.65.06, Driver version 3.27.1
> 
> #lspci -s 0001:02:04.0 -vvv
> 0001:02:04.0 SCSI storage controller: QLogic Corp. ISP1020/1040
> Fast-wide SCSI (rev 05)
>         Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>         Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-  
>         Latency: 248, Cache Line Size: 64 bytes
>         Interrupt: pin A routed to IRQ 52
>         Region 0: I/O ports at 200008000 [size=256]
>         Region 1: Memory at 209050000 (32-bit, non-prefetchable) [size=4K]
>         Expansion ROM at 209040000 [disabled] [size=64K]
>         Kernel driver in use: qla1280
>         Kernel modules: qla1280

0000:00:00.0 SCSI storage controller: QLogic Corp. ISP1020 Fast-wide SCSI (rev 05)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 256 bytes
	Interrupt: pin A routed to IRQ 8
	Region 0: I/O ports at 1f200000 [size=256]
	Region 1: Memory at 1f200000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at 1f210000 [disabled] [size=64K]
	Kernel driver in use: qla1280

0000:00:01.0 SCSI storage controller: QLogic Corp. ISP1020 Fast-wide SCSI (rev 05)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 256 bytes
	Interrupt: pin A routed to IRQ 9
	Region 0: I/O ports at 1f400000 [size=256]
	Region 1: Memory at 1f400000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at 1f410000 [disabled] [size=64K]
	Kernel driver in use: qla1280

qla1280: QLA1040 found on PCI bus 0, dev 0
qla1280 0000:00:00.0: enabling device (0006 -> 0007)
random: crng init done
cfg_0 5
scsi(0:0): Resetting SCSI BUS
scsi host0: QLogic QLA1040 PCI to SCSI Host Adapter
       Firmware version:  7.65.06, Driver version 3.27.1
qla1280: QLA1040 found on PCI bus 0, dev 1
qla1280 0000:00:01.0: enabling device (0006 -> 0007)
scsi 0:0:1:0: Direct-Access     FUJITSU  MAW3073NC        0104 PQ: 0 ANSI: 3
scsi(0:0:1:0): Sync: period 10, offset 12, Wide, Tagged queuing: depth 31
scsi 0:0:2:0: Direct-Access     SEAGATE  SX118202LS       B808 PQ: 0 ANSI: 2
scsi(0:0:2:0): Sync: period 10, offset 12, Wide, Tagged queuing: depth 31
cfg_0 5
scsi(1:0): Resetting SCSI BUS

So the Octane 1040 chips are the same revision and working with 64bit addressing.

Thomas.

-- 
SUSE Software Solutions Germany GmbH
HRB 36809 (AG Nürnberg)
Geschäftsführer: Ivo Totev, Andrew McDonald, Werner Knoblich