[PATCH AUTOSEL 6.6 01/15] scsi: hisi_sas: Fix I/O errors caused by hardware port ID changes

[PATCH AUTOSEL 6.6 01/15] scsi: hisi_sas: Fix I/O errors caused by hardware port ID changes

[Sasha Levin]

From: Xingui Yang <yangxingui@huawei.com>

[ Upstream commit daff37f00c7506ca322ccfce95d342022f06ec58 ]

The hw port ID of phy may change when inserting disks in batches, causing
the port ID in hisi_sas_port and itct to be inconsistent with the hardware,
resulting in I/O errors. The solution is to set the device state to gone to
intercept I/O sent to the device, and then execute linkreset to discard and
find the disk to re-update its information.

Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20250312095135.3048379-3-yangxingui@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/hisi_sas/hisi_sas_main.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/drivers/scsi/hisi_sas/hisi_sas_main.c b/drivers/scsi/hisi_sas/hisi_sas_main.c
index f78c5f8a49ffa..7e64661d215bd 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_main.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_main.c
@@ -911,8 +911,28 @@ static void hisi_sas_phyup_work_common(struct work_struct *work,
 		container_of(work, typeof(*phy), works[event]);
 	struct hisi_hba *hisi_hba = phy->hisi_hba;
 	struct asd_sas_phy *sas_phy = &phy->sas_phy;
+	struct asd_sas_port *sas_port = sas_phy->port;
+	struct hisi_sas_port *port = phy->port;
+	struct device *dev = hisi_hba->dev;
+	struct domain_device *port_dev;
 	int phy_no = sas_phy->id;
 
+	if (!test_bit(HISI_SAS_RESETTING_BIT, &hisi_hba->flags) &&
+	    sas_port && port && (port->id != phy->port_id)) {
+		dev_info(dev, "phy%d's hw port id changed from %d to %llu\n",
+				phy_no, port->id, phy->port_id);
+		port_dev = sas_port->port_dev;
+		if (port_dev && !dev_is_expander(port_dev->dev_type)) {
+			/*
+			 * Set the device state to gone to block
+			 * sending IO to the device.
+			 */
+			set_bit(SAS_DEV_GONE, &port_dev->state);
+			hisi_sas_notify_phy_event(phy, HISI_PHYE_LINK_RESET);
+			return;
+		}
+	}
+
 	phy->wait_phyup_cnt = 0;
 	if (phy->identify.target_port_protocols == SAS_PROTOCOL_SSP)
 		hisi_hba->hw->sl_notify_ssp(hisi_hba, phy_no);
-- 
2.39.5

[PATCH AUTOSEL 6.6 02/15] scsi: ufs: exynos: Ensure pre_link() executes before exynos_ufs_phy_init()

[Sasha Levin]

From: Peter Griffin <peter.griffin@linaro.org>

[ Upstream commit 3d101165e72316775947d71321d97194f03dfef3 ]

Ensure clocks are enabled before configuring unipro. Additionally move
the pre_link() hook before the exynos_ufs_phy_init() calls. This means
the register write sequence more closely resembles the ordering of the
downstream driver.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20250319-exynos-ufs-stability-fixes-v2-1-96722cc2ba1b@linaro.org
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/ufs/host/ufs-exynos.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/ufs/host/ufs-exynos.c b/drivers/ufs/host/ufs-exynos.c
index 268189f01e15b..76703a7fa5717 100644
--- a/drivers/ufs/host/ufs-exynos.c
+++ b/drivers/ufs/host/ufs-exynos.c
@@ -984,9 +984,14 @@ static int exynos_ufs_pre_link(struct ufs_hba *hba)
 	exynos_ufs_config_intr(ufs, DFES_DEF_L4_ERRS, UNIPRO_L4);
 	exynos_ufs_set_unipro_pclk_div(ufs);
 
+	exynos_ufs_setup_clocks(hba, true, PRE_CHANGE);
+
 	/* unipro */
 	exynos_ufs_config_unipro(ufs);
 
+	if (ufs->drv_data->pre_link)
+		ufs->drv_data->pre_link(ufs);
+
 	/* m-phy */
 	exynos_ufs_phy_init(ufs);
 	if (!(ufs->opts & EXYNOS_UFS_OPT_SKIP_CONFIG_PHY_ATTR)) {
@@ -994,11 +999,6 @@ static int exynos_ufs_pre_link(struct ufs_hba *hba)
 		exynos_ufs_config_phy_cap_attr(ufs);
 	}
 
-	exynos_ufs_setup_clocks(hba, true, PRE_CHANGE);
-
-	if (ufs->drv_data->pre_link)
-		ufs->drv_data->pre_link(ufs);
-
 	return 0;
 }
 
-- 
2.39.5

[PATCH AUTOSEL 6.6 03/15] scsi: pm80xx: Set phy_attached to zero when device is gone

[Sasha Levin]

From: Igor Pylypiv <ipylypiv@google.com>

[ Upstream commit f7b705c238d1483f0a766e2b20010f176e5c0fb7 ]

When a fatal error occurs, a phy down event may not be received to set
phy->phy_attached to zero.

Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Salomon Dushimirimana <salomondush@google.com>
Link: https://lore.kernel.org/r/20250319230305.3172920-1-salomondush@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/pm8001/pm8001_sas.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/scsi/pm8001/pm8001_sas.c b/drivers/scsi/pm8001/pm8001_sas.c
index ee2da8e49d4cf..a9d6dac413346 100644
--- a/drivers/scsi/pm8001/pm8001_sas.c
+++ b/drivers/scsi/pm8001/pm8001_sas.c
@@ -719,6 +719,7 @@ static void pm8001_dev_gone_notify(struct domain_device *dev)
 			spin_lock_irqsave(&pm8001_ha->lock, flags);
 		}
 		PM8001_CHIP_DISP->dereg_dev_req(pm8001_ha, device_id);
+		pm8001_ha->phy[pm8001_dev->attached_phy].phy_attached = 0;
 		pm8001_free_dev(pm8001_dev);
 	} else {
 		pm8001_dbg(pm8001_ha, DISC, "Found dev has gone.\n");
-- 
2.39.5