* [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types
@ 2025-03-10 15:55 Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 1/5] scsi: scsi_debug: Fix two typos in command definitions Kai Mäkisara
` (5 more replies)
0 siblings, 6 replies; 7+ messages in thread
From: Kai Mäkisara @ 2025-03-10 15:55 UTC (permalink / raw)
To: linux-scsi, dgilbert; +Cc: martin.petersen, James.Bottomley, Kai Mäkisara
The patch set includes changes to better support different device types.
The first patch fixes two obvious typos in the existing definitions.
The second patch adds a device type mask to the command definitions (struct
opcode_info_t). This makes possible for different command definitions for
different device types and makes easy to add opcodes specific to certain
device types. The mask is 32 bits wide and the bit positions are derived
from the Peripheral Device Type field returned from INQUIRY and used in
the struct scsi_device.
In addition to the mask, the second patch adds command filtering based on
device type to command queuing and building of the response in Report
Supported Opcodes.
The third patch splits definitions of READ(6), WRITE(6) and PRE-FETCH/READ
POSITION to versions for tapes and for other devices.
The fourth patch changes obtaining device type from sdebug_ptype to
struct scsi_device->type whenever it is set correctly. This improves
support for using different device types in the same debug host.
The patch set applies to 6.15/scsi-staging
v2:
- fixed devsel type in Patch 2, problem reported by the Kernel Test Robot
- added patch 5: Add ERASE for tapes
Kai Mäkisara (5):
scsi: scsi_debug: Fix two typos in command definitions
scsi: scsi_debug: Enable different command definitions for different
device types
scsi: scsi_debug: Move some tape-specific commands to separate
definitions
scsi: scsi_debug: Use scsi_device->type instead os sdebug_ptype where
possible
scsi_scsi_debug: Add ERASE for tapes
drivers/scsi/scsi_debug.c | 359 ++++++++++++++++++++++----------------
1 file changed, 205 insertions(+), 154 deletions(-)
--
2.43.0
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v2 1/5] scsi: scsi_debug: Fix two typos in command definitions
2025-03-10 15:55 [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Kai Mäkisara
@ 2025-03-10 15:55 ` Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 2/5] scsi: scsi_debug: Enable different command definitions for different device types Kai Mäkisara
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Kai Mäkisara @ 2025-03-10 15:55 UTC (permalink / raw)
To: linux-scsi, dgilbert; +Cc: martin.petersen, James.Bottomley, Kai Mäkisara
Fix two command definitions:
- flags and service action reversed in SEND DIAGNOSTIC
- ATOMIC WRITE missing opcode
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
---
drivers/scsi/scsi_debug.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/scsi/scsi_debug.c b/drivers/scsi/scsi_debug.c
index 523f054912e1..c5e7264748a8 100644
--- a/drivers/scsi/scsi_debug.c
+++ b/drivers/scsi/scsi_debug.c
@@ -817,7 +817,7 @@ static const struct opcode_info_t opcode_info_arr[SDEB_I_LAST_ELEM_P1 + 1] = {
{6, 0x1, 0, 0, 0, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
{0, 0, 0, F_INV_OP | FF_RESPOND, NULL, NULL, /* ATA_PT */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0x1d, F_D_OUT, 0, NULL, NULL, /* SEND DIAGNOSTIC */
+ {0, 0x1d, 0, F_D_OUT, NULL, NULL, /* SEND DIAGNOSTIC */
{6, 0xf7, 0, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
{0, 0x42, 0, F_D_OUT | FF_MEDIA_IO, resp_unmap, NULL, /* UNMAP */
{10, 0x1, 0, 0, 0, 0, 0x3f, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0} },
@@ -852,7 +852,7 @@ static const struct opcode_info_t opcode_info_arr[SDEB_I_LAST_ELEM_P1 + 1] = {
{16, 0x0 /* SA */, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xbf, 0xc7} },
/* 32 */
- {0, 0x0, 0x0, F_D_OUT | FF_MEDIA_IO,
+ {0, 0x9c, 0x0, F_D_OUT | FF_MEDIA_IO,
resp_atomic_write, NULL, /* ATOMIC WRITE 16 */
{16, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff} },
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v2 2/5] scsi: scsi_debug: Enable different command definitions for different device types
2025-03-10 15:55 [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 1/5] scsi: scsi_debug: Fix two typos in command definitions Kai Mäkisara
@ 2025-03-10 15:55 ` Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 3/5] scsi: scsi_debug: Move some tape-specific commands to separate definitions Kai Mäkisara
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Kai Mäkisara @ 2025-03-10 15:55 UTC (permalink / raw)
To: linux-scsi, dgilbert; +Cc: martin.petersen, James.Bottomley, Kai Mäkisara
Add mask field devsel to the struct opcode_info_t to enable different
definitions for different device types. Add checking of device mask to
command queuing and reporting of supported opcodes.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
---
v2:
- make sure that devsel is u32 in all functions
Reported by the Kernel Test Robot:
https://lore.kernel.org/linux-scsi/202503101506.7b02ef4b-lkp@intel.com/
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
---
drivers/scsi/scsi_debug.c | 204 +++++++++++++++++++++-----------------
1 file changed, 115 insertions(+), 89 deletions(-)
diff --git a/drivers/scsi/scsi_debug.c b/drivers/scsi/scsi_debug.c
index c5e7264748a8..4c2ee0a79c09 100644
--- a/drivers/scsi/scsi_debug.c
+++ b/drivers/scsi/scsi_debug.c
@@ -294,6 +294,14 @@ struct tape_block {
#define FF_SA (F_SA_HIGH | F_SA_LOW)
#define F_LONG_DELAY (F_SSU_DELAY | F_SYNC_DELAY)
+/* Device selection bit mask */
+#define DS_ALL 0xffffffff
+#define DS_SBC (1 << TYPE_DISK)
+#define DS_SSC (1 << TYPE_TAPE)
+#define DS_ZBC (1 << TYPE_ZBC)
+
+#define DS_NO_SSC (DS_ALL & ~DS_SSC)
+
#define SDEBUG_MAX_PARTS 4
#define SDEBUG_MAX_CMD_LEN 32
@@ -472,6 +480,7 @@ struct opcode_info_t {
/* for terminating element */
u8 opcode; /* if num_attached > 0, preferred */
u16 sa; /* service action */
+ u32 devsel; /* device type mask for this definition */
u32 flags; /* OR-ed set of SDEB_F_* */
int (*pfp)(struct scsi_cmnd *, struct sdebug_dev_info *);
const struct opcode_info_t *arrp; /* num_attached elements or NULL */
@@ -629,113 +638,113 @@ static void sdebug_erase_all_stores(bool apart_from_first);
* should be placed in opcode_info_arr[], the others should be placed here.
*/
static const struct opcode_info_t msense_iarr[] = {
- {0, 0x1a, 0, F_D_IN, NULL, NULL,
+ {0, 0x1a, 0, DS_ALL, F_D_IN, NULL, NULL,
{6, 0xe8, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
};
static const struct opcode_info_t mselect_iarr[] = {
- {0, 0x15, 0, F_D_OUT, NULL, NULL,
+ {0, 0x15, 0, DS_ALL, F_D_OUT, NULL, NULL,
{6, 0xf1, 0, 0, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
};
static const struct opcode_info_t read_iarr[] = {
- {0, 0x28, 0, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL,/* READ(10) */
+ {0, 0x28, 0, DS_NO_SSC, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL,/* READ(10) */
{10, 0xff, 0xff, 0xff, 0xff, 0xff, 0x3f, 0xff, 0xff, 0xc7, 0, 0,
0, 0, 0, 0} },
- {0, 0x8, 0, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL, /* READ(6) */
+ {0, 0x8, 0, DS_ALL, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL, /* READ(6) */
{6, 0xff, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0xa8, 0, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL,/* READ(12) */
+ {0, 0xa8, 0, DS_NO_SSC, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL,/* READ(12) */
{12, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xbf,
0xc7, 0, 0, 0, 0} },
};
static const struct opcode_info_t write_iarr[] = {
- {0, 0x2a, 0, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(10) */
+ {0, 0x2a, 0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(10) */
NULL, {10, 0xfb, 0xff, 0xff, 0xff, 0xff, 0x3f, 0xff, 0xff, 0xc7,
0, 0, 0, 0, 0, 0} },
- {0, 0xa, 0, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(6) */
+ {0, 0xa, 0, DS_ALL, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(6) */
NULL, {6, 0xff, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0} },
- {0, 0xaa, 0, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(12) */
+ {0, 0xaa, 0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(12) */
NULL, {12, 0xfb, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xbf, 0xc7, 0, 0, 0, 0} },
};
static const struct opcode_info_t verify_iarr[] = {
- {0, 0x2f, 0, F_D_OUT_MAYBE | FF_MEDIA_IO, resp_verify,/* VERIFY(10) */
+ {0, 0x2f, 0, DS_NO_SSC, F_D_OUT_MAYBE | FF_MEDIA_IO, resp_verify,/* VERIFY(10) */
NULL, {10, 0xf7, 0xff, 0xff, 0xff, 0xff, 0xbf, 0xff, 0xff, 0xc7,
0, 0, 0, 0, 0, 0} },
};
static const struct opcode_info_t sa_in_16_iarr[] = {
- {0, 0x9e, 0x12, F_SA_LOW | F_D_IN, resp_get_lba_status, NULL,
+ {0, 0x9e, 0x12, DS_NO_SSC, F_SA_LOW | F_D_IN, resp_get_lba_status, NULL,
{16, 0x12, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0, 0xc7} }, /* GET LBA STATUS(16) */
- {0, 0x9e, 0x16, F_SA_LOW | F_D_IN, resp_get_stream_status, NULL,
+ {0, 0x9e, 0x16, DS_NO_SSC, F_SA_LOW | F_D_IN, resp_get_stream_status, NULL,
{16, 0x16, 0, 0, 0xff, 0xff, 0, 0, 0, 0, 0xff, 0xff, 0xff, 0xff,
0, 0} }, /* GET STREAM STATUS */
};
static const struct opcode_info_t vl_iarr[] = { /* VARIABLE LENGTH */
- {0, 0x7f, 0xb, F_SA_HIGH | F_D_OUT | FF_MEDIA_IO, resp_write_dt0,
+ {0, 0x7f, 0xb, DS_NO_SSC, F_SA_HIGH | F_D_OUT | FF_MEDIA_IO, resp_write_dt0,
NULL, {32, 0xc7, 0, 0, 0, 0, 0x3f, 0x18, 0x0, 0xb, 0xfa,
0, 0xff, 0xff, 0xff, 0xff} }, /* WRITE(32) */
- {0, 0x7f, 0x11, F_SA_HIGH | F_D_OUT | FF_MEDIA_IO, resp_write_scat,
+ {0, 0x7f, 0x11, DS_NO_SSC, F_SA_HIGH | F_D_OUT | FF_MEDIA_IO, resp_write_scat,
NULL, {32, 0xc7, 0, 0, 0, 0, 0x3f, 0x18, 0x0, 0x11, 0xf8,
0, 0xff, 0xff, 0x0, 0x0} }, /* WRITE SCATTERED(32) */
};
static const struct opcode_info_t maint_in_iarr[] = { /* MAINT IN */
- {0, 0xa3, 0xc, F_SA_LOW | F_D_IN, resp_rsup_opcodes, NULL,
+ {0, 0xa3, 0xc, DS_ALL, F_SA_LOW | F_D_IN, resp_rsup_opcodes, NULL,
{12, 0xc, 0x87, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0,
0xc7, 0, 0, 0, 0} }, /* REPORT SUPPORTED OPERATION CODES */
- {0, 0xa3, 0xd, F_SA_LOW | F_D_IN, resp_rsup_tmfs, NULL,
+ {0, 0xa3, 0xd, DS_ALL, F_SA_LOW | F_D_IN, resp_rsup_tmfs, NULL,
{12, 0xd, 0x80, 0, 0, 0, 0xff, 0xff, 0xff, 0xff, 0, 0xc7, 0, 0,
0, 0} }, /* REPORTED SUPPORTED TASK MANAGEMENT FUNCTIONS */
};
static const struct opcode_info_t write_same_iarr[] = {
- {0, 0x93, 0, F_D_OUT_MAYBE | FF_MEDIA_IO, resp_write_same_16, NULL,
+ {0, 0x93, 0, DS_NO_SSC, F_D_OUT_MAYBE | FF_MEDIA_IO, resp_write_same_16, NULL,
{16, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0x3f, 0xc7} }, /* WRITE SAME(16) */
};
static const struct opcode_info_t reserve_iarr[] = {
- {0, 0x16, 0, F_D_OUT, NULL, NULL, /* RESERVE(6) */
+ {0, 0x16, 0, DS_ALL, F_D_OUT, NULL, NULL, /* RESERVE(6) */
{6, 0x1f, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
};
static const struct opcode_info_t release_iarr[] = {
- {0, 0x17, 0, F_D_OUT, NULL, NULL, /* RELEASE(6) */
+ {0, 0x17, 0, DS_ALL, F_D_OUT, NULL, NULL, /* RELEASE(6) */
{6, 0x1f, 0xff, 0, 0, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
};
static const struct opcode_info_t sync_cache_iarr[] = {
- {0, 0x91, 0, F_SYNC_DELAY | F_M_ACCESS, resp_sync_cache, NULL,
+ {0, 0x91, 0, DS_NO_SSC, F_SYNC_DELAY | F_M_ACCESS, resp_sync_cache, NULL,
{16, 0x6, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0x3f, 0xc7} }, /* SYNC_CACHE (16) */
};
static const struct opcode_info_t pre_fetch_iarr[] = {
- {0, 0x90, 0, F_SYNC_DELAY | FF_MEDIA_IO, resp_pre_fetch, NULL,
+ {0, 0x90, 0, DS_NO_SSC, F_SYNC_DELAY | FF_MEDIA_IO, resp_pre_fetch, NULL,
{16, 0x2, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0x3f, 0xc7} }, /* PRE-FETCH (16) */
};
static const struct opcode_info_t zone_out_iarr[] = { /* ZONE OUT(16) */
- {0, 0x94, 0x1, F_SA_LOW | F_M_ACCESS, resp_close_zone, NULL,
+ {0, 0x94, 0x1, DS_NO_SSC, F_SA_LOW | F_M_ACCESS, resp_close_zone, NULL,
{16, 0x1, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0, 0, 0xff, 0xff, 0x1, 0xc7} }, /* CLOSE ZONE */
- {0, 0x94, 0x2, F_SA_LOW | F_M_ACCESS, resp_finish_zone, NULL,
+ {0, 0x94, 0x2, DS_NO_SSC, F_SA_LOW | F_M_ACCESS, resp_finish_zone, NULL,
{16, 0x2, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0, 0, 0xff, 0xff, 0x1, 0xc7} }, /* FINISH ZONE */
- {0, 0x94, 0x4, F_SA_LOW | F_M_ACCESS, resp_rwp_zone, NULL,
+ {0, 0x94, 0x4, DS_NO_SSC, F_SA_LOW | F_M_ACCESS, resp_rwp_zone, NULL,
{16, 0x4, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0, 0, 0xff, 0xff, 0x1, 0xc7} }, /* RESET WRITE POINTER */
};
static const struct opcode_info_t zone_in_iarr[] = { /* ZONE IN(16) */
- {0, 0x95, 0x6, F_SA_LOW | F_D_IN | F_M_ACCESS, NULL, NULL,
+ {0, 0x95, 0x6, DS_NO_SSC, F_SA_LOW | F_D_IN | F_M_ACCESS, NULL, NULL,
{16, 0x6, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0x3f, 0xc7} }, /* REPORT ZONES */
};
@@ -746,130 +755,130 @@ static const struct opcode_info_t zone_in_iarr[] = { /* ZONE IN(16) */
* REPORT SUPPORTED OPERATION CODES. */
static const struct opcode_info_t opcode_info_arr[SDEB_I_LAST_ELEM_P1 + 1] = {
/* 0 */
- {0, 0, 0, F_INV_OP | FF_RESPOND, NULL, NULL, /* unknown opcodes */
+ {0, 0, 0, DS_ALL, F_INV_OP | FF_RESPOND, NULL, NULL, /* unknown opcodes */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0x12, 0, FF_RESPOND | F_D_IN, resp_inquiry, NULL, /* INQUIRY */
+ {0, 0x12, 0, DS_ALL, FF_RESPOND | F_D_IN, resp_inquiry, NULL, /* INQUIRY */
{6, 0xe3, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0xa0, 0, FF_RESPOND | F_D_IN, resp_report_luns, NULL,
+ {0, 0xa0, 0, DS_ALL, FF_RESPOND | F_D_IN, resp_report_luns, NULL,
{12, 0xe3, 0xff, 0, 0, 0, 0xff, 0xff, 0xff, 0xff, 0, 0xc7, 0, 0,
0, 0} }, /* REPORT LUNS */
- {0, 0x3, 0, FF_RESPOND | F_D_IN, resp_requests, NULL,
+ {0, 0x3, 0, DS_ALL, FF_RESPOND | F_D_IN, resp_requests, NULL,
{6, 0xe1, 0, 0, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0x0, 0, F_M_ACCESS | F_RL_WLUN_OK, NULL, NULL,/* TEST UNIT READY */
+ {0, 0x0, 0, DS_ALL, F_M_ACCESS | F_RL_WLUN_OK, NULL, NULL,/* TEST UNIT READY */
{6, 0, 0, 0, 0, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
/* 5 */
- {ARRAY_SIZE(msense_iarr), 0x5a, 0, F_D_IN, /* MODE SENSE(10) */
+ {ARRAY_SIZE(msense_iarr), 0x5a, 0, DS_ALL, F_D_IN, /* MODE SENSE(10) */
resp_mode_sense, msense_iarr, {10, 0xf8, 0xff, 0xff, 0, 0, 0,
0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0} },
- {ARRAY_SIZE(mselect_iarr), 0x55, 0, F_D_OUT, /* MODE SELECT(10) */
+ {ARRAY_SIZE(mselect_iarr), 0x55, 0, DS_ALL, F_D_OUT, /* MODE SELECT(10) */
resp_mode_select, mselect_iarr, {10, 0xf1, 0, 0, 0, 0, 0, 0xff,
0xff, 0xc7, 0, 0, 0, 0, 0, 0} },
- {0, 0x4d, 0, F_D_IN, resp_log_sense, NULL, /* LOG SENSE */
+ {0, 0x4d, 0, DS_NO_SSC, F_D_IN, resp_log_sense, NULL, /* LOG SENSE */
{10, 0xe3, 0xff, 0xff, 0, 0xff, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0,
0, 0, 0} },
- {0, 0x25, 0, F_D_IN, resp_readcap, NULL, /* READ CAPACITY(10) */
+ {0, 0x25, 0, DS_NO_SSC, F_D_IN, resp_readcap, NULL, /* READ CAPACITY(10) */
{10, 0xe1, 0xff, 0xff, 0xff, 0xff, 0, 0, 0x1, 0xc7, 0, 0, 0, 0,
0, 0} },
- {ARRAY_SIZE(read_iarr), 0x88, 0, F_D_IN | FF_MEDIA_IO, /* READ(16) */
+ {ARRAY_SIZE(read_iarr), 0x88, 0, DS_NO_SSC, F_D_IN | FF_MEDIA_IO, /* READ(16) */
resp_read_dt0, read_iarr, {16, 0xfe, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xc7} },
/* 10 */
- {ARRAY_SIZE(write_iarr), 0x8a, 0, F_D_OUT | FF_MEDIA_IO,
+ {ARRAY_SIZE(write_iarr), 0x8a, 0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO,
resp_write_dt0, write_iarr, /* WRITE(16) */
{16, 0xfa, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0xff, 0xc7} },
- {0, 0x1b, 0, F_SSU_DELAY, resp_start_stop, NULL,/* START STOP UNIT */
+ {0, 0x1b, 0, DS_ALL, F_SSU_DELAY, resp_start_stop, NULL,/* START STOP UNIT */
{6, 0x1, 0, 0xf, 0xf7, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {ARRAY_SIZE(sa_in_16_iarr), 0x9e, 0x10, F_SA_LOW | F_D_IN,
+ {ARRAY_SIZE(sa_in_16_iarr), 0x9e, 0x10, DS_NO_SSC, F_SA_LOW | F_D_IN,
resp_readcap16, sa_in_16_iarr, /* SA_IN(16), READ CAPACITY(16) */
{16, 0x10, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0x1, 0xc7} },
- {0, 0x9f, 0x12, F_SA_LOW | F_D_OUT | FF_MEDIA_IO, resp_write_scat,
+ {0, 0x9f, 0x12, DS_NO_SSC, F_SA_LOW | F_D_OUT | FF_MEDIA_IO, resp_write_scat,
NULL, {16, 0x12, 0xf9, 0x0, 0xff, 0xff, 0, 0, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0xc7} }, /* SA_OUT(16), WRITE SCAT(16) */
- {ARRAY_SIZE(maint_in_iarr), 0xa3, 0xa, F_SA_LOW | F_D_IN,
+ {ARRAY_SIZE(maint_in_iarr), 0xa3, 0xa, DS_ALL, F_SA_LOW | F_D_IN,
resp_report_tgtpgs, /* MAINT IN, REPORT TARGET PORT GROUPS */
maint_in_iarr, {12, 0xea, 0, 0, 0, 0, 0xff, 0xff, 0xff,
0xff, 0, 0xc7, 0, 0, 0, 0} },
/* 15 */
- {0, 0, 0, F_INV_OP | FF_RESPOND, NULL, NULL, /* MAINT OUT */
+ {0, 0, 0, DS_ALL, F_INV_OP | FF_RESPOND, NULL, NULL, /* MAINT OUT */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {ARRAY_SIZE(verify_iarr), 0x8f, 0,
+ {ARRAY_SIZE(verify_iarr), 0x8f, 0, DS_NO_SSC,
F_D_OUT_MAYBE | FF_MEDIA_IO, resp_verify, /* VERIFY(16) */
verify_iarr, {16, 0xf6, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0x3f, 0xc7} },
- {ARRAY_SIZE(vl_iarr), 0x7f, 0x9, F_SA_HIGH | F_D_IN | FF_MEDIA_IO,
+ {ARRAY_SIZE(vl_iarr), 0x7f, 0x9, DS_NO_SSC, F_SA_HIGH | F_D_IN | FF_MEDIA_IO,
resp_read_dt0, vl_iarr, /* VARIABLE LENGTH, READ(32) */
{32, 0xc7, 0, 0, 0, 0, 0x3f, 0x18, 0x0, 0x9, 0xfe, 0, 0xff, 0xff,
0xff, 0xff} },
- {ARRAY_SIZE(reserve_iarr), 0x56, 0, F_D_OUT,
+ {ARRAY_SIZE(reserve_iarr), 0x56, 0, DS_ALL, F_D_OUT,
NULL, reserve_iarr, /* RESERVE(10) <no response function> */
{10, 0xff, 0xff, 0xff, 0, 0, 0, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0,
0} },
- {ARRAY_SIZE(release_iarr), 0x57, 0, F_D_OUT,
+ {ARRAY_SIZE(release_iarr), 0x57, 0, DS_ALL, F_D_OUT,
NULL, release_iarr, /* RELEASE(10) <no response function> */
{10, 0x13, 0xff, 0xff, 0, 0, 0, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0,
0} },
/* 20 */
- {0, 0x1e, 0, 0, NULL, NULL, /* ALLOW REMOVAL */
+ {0, 0x1e, 0, DS_ALL, 0, NULL, NULL, /* ALLOW REMOVAL */
{6, 0, 0, 0, 0x3, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0x1, 0, 0, resp_rewind, NULL,
+ {0, 0x1, 0, DS_SSC, 0, resp_rewind, NULL,
{6, 0x1, 0, 0, 0, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0, 0, F_INV_OP | FF_RESPOND, NULL, NULL, /* ATA_PT */
+ {0, 0, 0, DS_NO_SSC, F_INV_OP | FF_RESPOND, NULL, NULL, /* ATA_PT */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0x1d, 0, F_D_OUT, NULL, NULL, /* SEND DIAGNOSTIC */
+ {0, 0x1d, 0, DS_ALL, F_D_OUT, NULL, NULL, /* SEND DIAGNOSTIC */
{6, 0xf7, 0, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0x42, 0, F_D_OUT | FF_MEDIA_IO, resp_unmap, NULL, /* UNMAP */
+ {0, 0x42, 0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO, resp_unmap, NULL, /* UNMAP */
{10, 0x1, 0, 0, 0, 0, 0x3f, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0} },
/* 25 */
- {0, 0x3b, 0, F_D_OUT_MAYBE, resp_write_buffer, NULL,
+ {0, 0x3b, 0, DS_NO_SSC, F_D_OUT_MAYBE, resp_write_buffer, NULL,
{10, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xc7, 0, 0,
0, 0, 0, 0} }, /* WRITE_BUFFER */
- {ARRAY_SIZE(write_same_iarr), 0x41, 0, F_D_OUT_MAYBE | FF_MEDIA_IO,
+ {ARRAY_SIZE(write_same_iarr), 0x41, 0, DS_NO_SSC, F_D_OUT_MAYBE | FF_MEDIA_IO,
resp_write_same_10, write_same_iarr, /* WRITE SAME(10) */
{10, 0xff, 0xff, 0xff, 0xff, 0xff, 0x3f, 0xff, 0xff, 0xc7, 0,
0, 0, 0, 0, 0} },
- {ARRAY_SIZE(sync_cache_iarr), 0x35, 0, F_SYNC_DELAY | F_M_ACCESS,
+ {ARRAY_SIZE(sync_cache_iarr), 0x35, 0, DS_NO_SSC, F_SYNC_DELAY | F_M_ACCESS,
resp_sync_cache, sync_cache_iarr,
{10, 0x7, 0xff, 0xff, 0xff, 0xff, 0x3f, 0xff, 0xff, 0xc7, 0, 0,
0, 0, 0, 0} }, /* SYNC_CACHE (10) */
- {0, 0x89, 0, F_D_OUT | FF_MEDIA_IO, resp_comp_write, NULL,
+ {0, 0x89, 0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO, resp_comp_write, NULL,
{16, 0xf8, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0, 0,
0, 0xff, 0x3f, 0xc7} }, /* COMPARE AND WRITE */
- {ARRAY_SIZE(pre_fetch_iarr), 0x34, 0, F_SYNC_DELAY | FF_MEDIA_IO,
+ {ARRAY_SIZE(pre_fetch_iarr), 0x34, 0, DS_ALL, F_SYNC_DELAY | FF_MEDIA_IO,
resp_pre_fetch, pre_fetch_iarr,
{10, 0x2, 0xff, 0xff, 0xff, 0xff, 0x3f, 0xff, 0xff, 0xc7, 0, 0,
0, 0, 0, 0} }, /* PRE-FETCH (10) */
/* READ POSITION (10) */
/* 30 */
- {ARRAY_SIZE(zone_out_iarr), 0x94, 0x3, F_SA_LOW | F_M_ACCESS,
+ {ARRAY_SIZE(zone_out_iarr), 0x94, 0x3, DS_NO_SSC, F_SA_LOW | F_M_ACCESS,
resp_open_zone, zone_out_iarr, /* ZONE_OUT(16), OPEN ZONE) */
{16, 0x3 /* SA */, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0x0, 0x0, 0xff, 0xff, 0x1, 0xc7} },
- {ARRAY_SIZE(zone_in_iarr), 0x95, 0x0, F_SA_LOW | F_M_ACCESS,
+ {ARRAY_SIZE(zone_in_iarr), 0x95, 0x0, DS_NO_SSC, F_SA_LOW | F_M_ACCESS,
resp_report_zones, zone_in_iarr, /* ZONE_IN(16), REPORT ZONES) */
{16, 0x0 /* SA */, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xbf, 0xc7} },
/* 32 */
- {0, 0x9c, 0x0, F_D_OUT | FF_MEDIA_IO,
+ {0, 0x9c, 0x0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO,
resp_atomic_write, NULL, /* ATOMIC WRITE 16 */
{16, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff} },
- {0, 0x05, 0, F_D_IN, resp_read_blklimits, NULL, /* READ BLOCK LIMITS (6) */
+ {0, 0x05, 0, DS_SSC, F_D_IN, resp_read_blklimits, NULL, /* READ BLOCK LIMITS (6) */
{6, 0, 0, 0, 0, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0x2b, 0, F_D_UNKN, resp_locate, NULL, /* LOCATE (10) */
+ {0, 0x2b, 0, DS_SSC, F_D_UNKN, resp_locate, NULL, /* LOCATE (10) */
{10, 0x07, 0, 0xff, 0xff, 0xff, 0xff, 0, 0xff, 0xc7, 0, 0,
0, 0, 0, 0} },
- {0, 0x10, 0, F_D_IN, resp_write_filemarks, NULL, /* WRITE FILEMARKS (6) */
+ {0, 0x10, 0, DS_SSC, F_D_IN, resp_write_filemarks, NULL, /* WRITE FILEMARKS (6) */
{6, 0x01, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0x11, 0, F_D_IN, resp_space, NULL, /* SPACE (6) */
+ {0, 0x11, 0, DS_SSC, F_D_IN, resp_space, NULL, /* SPACE (6) */
{6, 0x07, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
- {0, 0x4, 0, 0, resp_format_medium, NULL, /* FORMAT MEDIUM (6) */
+ {0, 0x4, 0, DS_SSC, 0, resp_format_medium, NULL, /* FORMAT MEDIUM (6) */
{6, 0x3, 0x7, 0, 0, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
/* 38 */
/* sentinel */
- {0xff, 0, 0, 0, NULL, NULL, /* terminating element */
+ {0xff, 0, 0, 0, 0, NULL, NULL, /* terminating element */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
};
@@ -1015,6 +1024,19 @@ static const int condition_met_result = SAM_STAT_CONDITION_MET;
static struct dentry *sdebug_debugfs_root;
static ASYNC_DOMAIN_EXCLUSIVE(sdebug_async_domain);
+static u32 sdebug_get_devsel(struct scsi_device *sdp)
+{
+ unsigned char devtype = sdp->type;
+ u32 devsel;
+
+ if (devtype < 32)
+ devsel = (1 << devtype);
+ else
+ devsel = DS_ALL;
+
+ return devsel;
+}
+
static void sdebug_err_free(struct rcu_head *head)
{
struct sdebug_err_inject *inject =
@@ -2454,11 +2476,12 @@ static int resp_rsup_opcodes(struct scsi_cmnd *scp,
u8 reporting_opts, req_opcode, sdeb_i, supp;
u16 req_sa, u;
u32 alloc_len, a_len;
- int k, offset, len, errsts, count, bump, na;
+ int k, offset, len, errsts, bump, na;
const struct opcode_info_t *oip;
const struct opcode_info_t *r_oip;
u8 *arr;
u8 *cmd = scp->cmnd;
+ u32 devsel = sdebug_get_devsel(scp->device);
rctd = !!(cmd[2] & 0x80);
reporting_opts = cmd[2] & 0x7;
@@ -2481,34 +2504,30 @@ static int resp_rsup_opcodes(struct scsi_cmnd *scp,
}
switch (reporting_opts) {
case 0: /* all commands */
- /* count number of commands */
- for (count = 0, oip = opcode_info_arr;
- oip->num_attached != 0xff; ++oip) {
- if (F_INV_OP & oip->flags)
- continue;
- count += (oip->num_attached + 1);
- }
bump = rctd ? 20 : 8;
- put_unaligned_be32(count * bump, arr);
for (offset = 4, oip = opcode_info_arr;
oip->num_attached != 0xff && offset < a_len; ++oip) {
if (F_INV_OP & oip->flags)
continue;
+ if ((devsel & oip->devsel) != 0) {
+ arr[offset] = oip->opcode;
+ put_unaligned_be16(oip->sa, arr + offset + 2);
+ if (rctd)
+ arr[offset + 5] |= 0x2;
+ if (FF_SA & oip->flags)
+ arr[offset + 5] |= 0x1;
+ put_unaligned_be16(oip->len_mask[0], arr + offset + 6);
+ if (rctd)
+ put_unaligned_be16(0xa, arr + offset + 8);
+ offset += bump;
+ }
na = oip->num_attached;
- arr[offset] = oip->opcode;
- put_unaligned_be16(oip->sa, arr + offset + 2);
- if (rctd)
- arr[offset + 5] |= 0x2;
- if (FF_SA & oip->flags)
- arr[offset + 5] |= 0x1;
- put_unaligned_be16(oip->len_mask[0], arr + offset + 6);
- if (rctd)
- put_unaligned_be16(0xa, arr + offset + 8);
r_oip = oip;
for (k = 0, oip = oip->arrp; k < na; ++k, ++oip) {
if (F_INV_OP & oip->flags)
continue;
- offset += bump;
+ if ((devsel & oip->devsel) == 0)
+ continue;
arr[offset] = oip->opcode;
put_unaligned_be16(oip->sa, arr + offset + 2);
if (rctd)
@@ -2516,14 +2535,15 @@ static int resp_rsup_opcodes(struct scsi_cmnd *scp,
if (FF_SA & oip->flags)
arr[offset + 5] |= 0x1;
put_unaligned_be16(oip->len_mask[0],
- arr + offset + 6);
+ arr + offset + 6);
if (rctd)
put_unaligned_be16(0xa,
arr + offset + 8);
+ offset += bump;
}
oip = r_oip;
- offset += bump;
}
+ put_unaligned_be32(offset - 4, arr);
break;
case 1: /* one command: opcode only */
case 2: /* one command: opcode plus service action */
@@ -2549,13 +2569,15 @@ static int resp_rsup_opcodes(struct scsi_cmnd *scp,
return check_condition_result;
}
if (0 == (FF_SA & oip->flags) &&
- req_opcode == oip->opcode)
+ (devsel & oip->devsel) != 0 &&
+ req_opcode == oip->opcode)
supp = 3;
else if (0 == (FF_SA & oip->flags)) {
na = oip->num_attached;
for (k = 0, oip = oip->arrp; k < na;
++k, ++oip) {
- if (req_opcode == oip->opcode)
+ if (req_opcode == oip->opcode &&
+ (devsel & oip->devsel) != 0)
break;
}
supp = (k >= na) ? 1 : 3;
@@ -2563,7 +2585,8 @@ static int resp_rsup_opcodes(struct scsi_cmnd *scp,
na = oip->num_attached;
for (k = 0, oip = oip->arrp; k < na;
++k, ++oip) {
- if (req_sa == oip->sa)
+ if (req_sa == oip->sa &&
+ (devsel & oip->devsel) != 0)
break;
}
supp = (k >= na) ? 1 : 3;
@@ -9173,6 +9196,7 @@ static int scsi_debug_queuecommand(struct Scsi_Host *shost,
u32 flags;
u16 sa;
u8 opcode = cmd[0];
+ u32 devsel = sdebug_get_devsel(scp->device);
bool has_wlun_rl;
bool inject_now;
int ret = 0;
@@ -9252,12 +9276,14 @@ static int scsi_debug_queuecommand(struct Scsi_Host *shost,
else
sa = get_unaligned_be16(cmd + 8);
for (k = 0; k <= na; oip = r_oip->arrp + k++) {
- if (opcode == oip->opcode && sa == oip->sa)
+ if (opcode == oip->opcode && sa == oip->sa &&
+ (devsel & oip->devsel) != 0)
break;
}
} else { /* since no service action only check opcode */
for (k = 0; k <= na; oip = r_oip->arrp + k++) {
- if (opcode == oip->opcode)
+ if (opcode == oip->opcode &&
+ (devsel & oip->devsel) != 0)
break;
}
}
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v2 3/5] scsi: scsi_debug: Move some tape-specific commands to separate definitions
2025-03-10 15:55 [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 1/5] scsi: scsi_debug: Fix two typos in command definitions Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 2/5] scsi: scsi_debug: Enable different command definitions for different device types Kai Mäkisara
@ 2025-03-10 15:55 ` Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 4/5] scsi: scsi_debug: Use scsi_device->type instead os sdebug_ptype where possible Kai Mäkisara
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Kai Mäkisara @ 2025-03-10 15:55 UTC (permalink / raw)
To: linux-scsi, dgilbert; +Cc: martin.petersen, James.Bottomley, Kai Mäkisara
New definitions (struct opcode_info_t) are created for READ(6),
WRITE(6), READ POSITION(10) for tape devices.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
---
drivers/scsi/scsi_debug.c | 77 +++++++++++++++++++--------------------
1 file changed, 38 insertions(+), 39 deletions(-)
diff --git a/drivers/scsi/scsi_debug.c b/drivers/scsi/scsi_debug.c
index 4c2ee0a79c09..04e2d0928b30 100644
--- a/drivers/scsi/scsi_debug.c
+++ b/drivers/scsi/scsi_debug.c
@@ -594,7 +594,9 @@ static int resp_mode_select(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_log_sense(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_readcap(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_read_dt0(struct scsi_cmnd *, struct sdebug_dev_info *);
+static int resp_read_tape(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_write_dt0(struct scsi_cmnd *, struct sdebug_dev_info *);
+static int resp_write_tape(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_write_scat(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_start_stop(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_readcap16(struct scsi_cmnd *, struct sdebug_dev_info *);
@@ -622,6 +624,7 @@ static int resp_read_blklimits(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_locate(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_write_filemarks(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_space(struct scsi_cmnd *, struct sdebug_dev_info *);
+static int resp_read_position(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_rewind(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_format_medium(struct scsi_cmnd *, struct sdebug_dev_info *);
@@ -651,8 +654,10 @@ static const struct opcode_info_t read_iarr[] = {
{0, 0x28, 0, DS_NO_SSC, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL,/* READ(10) */
{10, 0xff, 0xff, 0xff, 0xff, 0xff, 0x3f, 0xff, 0xff, 0xc7, 0, 0,
0, 0, 0, 0} },
- {0, 0x8, 0, DS_ALL, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL, /* READ(6) */
+ {0, 0x8, 0, DS_NO_SSC, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL, /* READ(6) disk */
{6, 0xff, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
+ {0, 0x8, 0, DS_SSC, F_D_IN | FF_MEDIA_IO, resp_read_tape, NULL, /* READ(6) tape */
+ {6, 0x03, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
{0, 0xa8, 0, DS_NO_SSC, F_D_IN | FF_MEDIA_IO, resp_read_dt0, NULL,/* READ(12) */
{12, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xbf,
0xc7, 0, 0, 0, 0} },
@@ -662,9 +667,12 @@ static const struct opcode_info_t write_iarr[] = {
{0, 0x2a, 0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(10) */
NULL, {10, 0xfb, 0xff, 0xff, 0xff, 0xff, 0x3f, 0xff, 0xff, 0xc7,
0, 0, 0, 0, 0, 0} },
- {0, 0xa, 0, DS_ALL, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(6) */
+ {0, 0xa, 0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(6) disk */
NULL, {6, 0xff, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0} },
+ {0, 0xa, 0, DS_SSC, F_D_OUT | FF_MEDIA_IO, resp_write_tape, /* WRITE(6) tape */
+ NULL, {6, 0x01, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0} },
{0, 0xaa, 0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO, resp_write_dt0, /* WRITE(12) */
NULL, {12, 0xfb, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xbf, 0xc7, 0, 0, 0, 0} },
@@ -729,6 +737,9 @@ static const struct opcode_info_t pre_fetch_iarr[] = {
{0, 0x90, 0, DS_NO_SSC, F_SYNC_DELAY | FF_MEDIA_IO, resp_pre_fetch, NULL,
{16, 0x2, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
0xff, 0xff, 0xff, 0xff, 0x3f, 0xc7} }, /* PRE-FETCH (16) */
+ {0, 0x34, 0, DS_SSC, F_SYNC_DELAY | FF_MEDIA_IO, resp_read_position, NULL,
+ {10, 0x1f, 0x00, 0x00, 0x00, 0x00, 0x00, 0xff, 0xff, 0xc7, 0, 0,
+ 0, 0, 0, 0} }, /* READ POSITION (10) */
};
static const struct opcode_info_t zone_out_iarr[] = { /* ZONE OUT(16) */
@@ -845,7 +856,7 @@ static const struct opcode_info_t opcode_info_arr[SDEB_I_LAST_ELEM_P1 + 1] = {
{0, 0x89, 0, DS_NO_SSC, F_D_OUT | FF_MEDIA_IO, resp_comp_write, NULL,
{16, 0xf8, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0, 0,
0, 0xff, 0x3f, 0xc7} }, /* COMPARE AND WRITE */
- {ARRAY_SIZE(pre_fetch_iarr), 0x34, 0, DS_ALL, F_SYNC_DELAY | FF_MEDIA_IO,
+ {ARRAY_SIZE(pre_fetch_iarr), 0x34, 0, DS_NO_SSC, F_SYNC_DELAY | FF_MEDIA_IO,
resp_pre_fetch, pre_fetch_iarr,
{10, 0x2, 0xff, 0xff, 0xff, 0xff, 0x3f, 0xff, 0xff, 0xc7, 0, 0,
0, 0, 0, 0} }, /* PRE-FETCH (10) */
@@ -3586,6 +3597,30 @@ static int resp_space(struct scsi_cmnd *scp,
return check_condition_result;
}
+enum {SDEBUG_READ_POSITION_ARR_SZ = 20};
+static int resp_read_position(struct scsi_cmnd *scp,
+ struct sdebug_dev_info *devip)
+{
+ u8 *cmd = scp->cmnd;
+ int all_length;
+ unsigned char arr[20];
+ unsigned int pos;
+
+ all_length = get_unaligned_be16(cmd + 7);
+ if ((cmd[1] & 0xfe) != 0 ||
+ all_length != 0) { /* only short form */
+ mk_sense_invalid_fld(scp, SDEB_IN_CDB,
+ all_length ? 7 : 1, 0);
+ return check_condition_result;
+ }
+ memset(arr, 0, SDEBUG_READ_POSITION_ARR_SZ);
+ arr[1] = devip->tape_partition;
+ pos = devip->tape_location[devip->tape_partition];
+ put_unaligned_be32(pos, arr + 4);
+ put_unaligned_be32(pos, arr + 8);
+ return fill_from_dev_buffer(scp, arr, SDEBUG_READ_POSITION_ARR_SZ);
+}
+
static int resp_rewind(struct scsi_cmnd *scp,
struct sdebug_dev_info *devip)
{
@@ -3627,10 +3662,6 @@ static int resp_format_medium(struct scsi_cmnd *scp,
int res = 0;
unsigned char *cmd = scp->cmnd;
- if (sdebug_ptype != TYPE_TAPE) {
- mk_sense_invalid_fld(scp, SDEB_IN_CDB, 0, -1);
- return check_condition_result;
- }
if (cmd[2] > 2) {
mk_sense_invalid_fld(scp, SDEB_IN_DATA, 2, -1);
return check_condition_result;
@@ -4490,9 +4521,6 @@ static int resp_read_dt0(struct scsi_cmnd *scp, struct sdebug_dev_info *devip)
u8 *cmd = scp->cmnd;
bool meta_data_locked = false;
- if (sdebug_ptype == TYPE_TAPE)
- return resp_read_tape(scp, devip);
-
switch (cmd[0]) {
case READ_16:
ei_lba = 0;
@@ -4862,9 +4890,6 @@ static int resp_write_dt0(struct scsi_cmnd *scp, struct sdebug_dev_info *devip)
u8 *cmd = scp->cmnd;
bool meta_data_locked = false;
- if (sdebug_ptype == TYPE_TAPE)
- return resp_write_tape(scp, devip);
-
switch (cmd[0]) {
case WRITE_16:
ei_lba = 0;
@@ -5596,7 +5621,6 @@ static int resp_sync_cache(struct scsi_cmnd *scp,
*
* The pcode 0x34 is also used for READ POSITION by tape devices.
*/
-enum {SDEBUG_READ_POSITION_ARR_SZ = 20};
static int resp_pre_fetch(struct scsi_cmnd *scp,
struct sdebug_dev_info *devip)
{
@@ -5608,31 +5632,6 @@ static int resp_pre_fetch(struct scsi_cmnd *scp,
struct sdeb_store_info *sip = devip2sip(devip, true);
u8 *fsp = sip->storep;
- if (sdebug_ptype == TYPE_TAPE) {
- if (cmd[0] == PRE_FETCH) { /* READ POSITION (10) */
- int all_length;
- unsigned char arr[20];
- unsigned int pos;
-
- all_length = get_unaligned_be16(cmd + 7);
- if ((cmd[1] & 0xfe) != 0 ||
- all_length != 0) { /* only short form */
- mk_sense_invalid_fld(scp, SDEB_IN_CDB,
- all_length ? 7 : 1, 0);
- return check_condition_result;
- }
- memset(arr, 0, SDEBUG_READ_POSITION_ARR_SZ);
- arr[1] = devip->tape_partition;
- pos = devip->tape_location[devip->tape_partition];
- put_unaligned_be32(pos, arr + 4);
- put_unaligned_be32(pos, arr + 8);
- return fill_from_dev_buffer(scp, arr,
- SDEBUG_READ_POSITION_ARR_SZ);
- }
- mk_sense_invalid_opcode(scp);
- return check_condition_result;
- }
-
if (cmd[0] == PRE_FETCH) { /* 10 byte cdb */
lba = get_unaligned_be32(cmd + 2);
nblks = get_unaligned_be16(cmd + 7);
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v2 4/5] scsi: scsi_debug: Use scsi_device->type instead os sdebug_ptype where possible
2025-03-10 15:55 [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Kai Mäkisara
` (2 preceding siblings ...)
2025-03-10 15:55 ` [PATCH v2 3/5] scsi: scsi_debug: Move some tape-specific commands to separate definitions Kai Mäkisara
@ 2025-03-10 15:55 ` Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 5/5] scsi_scsi_debug: Add ERASE for tapes Kai Mäkisara
2025-04-11 20:23 ` [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Martin K. Petersen
5 siblings, 0 replies; 7+ messages in thread
From: Kai Mäkisara @ 2025-03-10 15:55 UTC (permalink / raw)
To: linux-scsi, dgilbert; +Cc: martin.petersen, James.Bottomley, Kai Mäkisara
Devices of several types can be created for a single host. The module
device type should be used only when the devices are created.
Scsi_scan sets the device type initially to 0xff and sets the correct
type based in Inquiry results. This means that Inquiry must report
sdebug_ptype as long as scsi_device->type is not set (the limit 32
comes from the 5-bit length of the Peripheral Device Type in Inquiry).
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
---
drivers/scsi/scsi_debug.c | 61 ++++++++++++++++++++++-----------------
1 file changed, 35 insertions(+), 26 deletions(-)
diff --git a/drivers/scsi/scsi_debug.c b/drivers/scsi/scsi_debug.c
index 04e2d0928b30..e4b336cc0a5f 100644
--- a/drivers/scsi/scsi_debug.c
+++ b/drivers/scsi/scsi_debug.c
@@ -2065,13 +2065,19 @@ static int resp_inquiry(struct scsi_cmnd *scp, struct sdebug_dev_info *devip)
unsigned char *cmd = scp->cmnd;
u32 alloc_len, n;
int ret;
- bool have_wlun, is_disk, is_zbc, is_disk_zbc;
+ bool have_wlun, is_disk, is_zbc, is_disk_zbc, is_tape;
alloc_len = get_unaligned_be16(cmd + 3);
arr = kzalloc(SDEBUG_MAX_INQ_ARR_SZ, GFP_ATOMIC);
if (! arr)
return DID_REQUEUE << 16;
- is_disk = (sdebug_ptype == TYPE_DISK);
+ if (scp->device->type >= 32) {
+ is_disk = (sdebug_ptype == TYPE_DISK);
+ is_tape = (sdebug_ptype == TYPE_TAPE);
+ } else {
+ is_disk = (scp->device->type == TYPE_DISK);
+ is_tape = (scp->device->type == TYPE_TAPE);
+ }
is_zbc = devip->zoned;
is_disk_zbc = (is_disk || is_zbc);
have_wlun = scsi_is_wlun(scp->device->lun);
@@ -2080,7 +2086,8 @@ static int resp_inquiry(struct scsi_cmnd *scp, struct sdebug_dev_info *devip)
else if (sdebug_no_lun_0 && (devip->lun == SDEBUG_LUN_0_VAL))
pq_pdt = 0x7f; /* not present, PQ=3, PDT=0x1f */
else
- pq_pdt = (sdebug_ptype & 0x1f);
+ pq_pdt = ((scp->device->type >= 32 ?
+ sdebug_ptype : scp->device->type) & 0x1f);
arr[0] = pq_pdt;
if (0x2 & cmd[1]) { /* CMDDT bit set */
mk_sense_invalid_fld(scp, SDEB_IN_CDB, 1, 1);
@@ -2203,7 +2210,7 @@ static int resp_inquiry(struct scsi_cmnd *scp, struct sdebug_dev_info *devip)
if (is_disk) { /* SBC-4 no version claimed */
put_unaligned_be16(0x600, arr + n);
n += 2;
- } else if (sdebug_ptype == TYPE_TAPE) { /* SSC-4 rev 3 */
+ } else if (is_tape) { /* SSC-4 rev 3 */
put_unaligned_be16(0x525, arr + n);
n += 2;
} else if (is_zbc) { /* ZBC BSR INCITS 536 revision 05 */
@@ -2312,7 +2319,7 @@ static int resp_start_stop(struct scsi_cmnd *scp, struct sdebug_dev_info *devip)
changing = (stopped_state != want_stop);
if (changing)
atomic_xchg(&devip->stopped, want_stop);
- if (sdebug_ptype == TYPE_TAPE && !want_stop) {
+ if (scp->device->type == TYPE_TAPE && !want_stop) {
int i;
set_bit(SDEBUG_UA_NOT_READY_TO_READY, devip->uas_bm); /* not legal! */
@@ -2948,9 +2955,9 @@ static int resp_mode_sense(struct scsi_cmnd *scp,
subpcode = cmd[3];
msense_6 = (MODE_SENSE == cmd[0]);
llbaa = msense_6 ? false : !!(cmd[1] & 0x10);
- is_disk = (sdebug_ptype == TYPE_DISK);
+ is_disk = (scp->device->type == TYPE_DISK);
is_zbc = devip->zoned;
- is_tape = (sdebug_ptype == TYPE_TAPE);
+ is_tape = (scp->device->type == TYPE_TAPE);
if ((is_disk || is_zbc || is_tape) && !dbd)
bd_len = llbaa ? 16 : 8;
else
@@ -3165,7 +3172,7 @@ static int resp_mode_select(struct scsi_cmnd *scp,
md_len = mselect6 ? (arr[0] + 1) : (get_unaligned_be16(arr + 0) + 2);
bd_len = mselect6 ? arr[3] : get_unaligned_be16(arr + 6);
off = (mselect6 ? 4 : 8);
- if (sdebug_ptype == TYPE_TAPE) {
+ if (scp->device->type == TYPE_TAPE) {
int blksize;
if (bd_len != 8) {
@@ -3230,7 +3237,7 @@ static int resp_mode_select(struct scsi_cmnd *scp,
}
break;
case 0xf: /* Compression mode page */
- if (sdebug_ptype != TYPE_TAPE)
+ if (scp->device->type != TYPE_TAPE)
goto bad_pcode;
if ((arr[off + 2] & 0x40) != 0) {
devip->tape_dce = (arr[off + 2] & 0x80) != 0;
@@ -3238,7 +3245,7 @@ static int resp_mode_select(struct scsi_cmnd *scp,
}
break;
case 0x11: /* Medium Partition Mode Page (tape) */
- if (sdebug_ptype == TYPE_TAPE) {
+ if (scp->device->type == TYPE_TAPE) {
int fld;
fld = process_medium_part_m_pg(devip, &arr[off], pg_len);
@@ -6667,7 +6674,7 @@ static void scsi_debug_sdev_destroy(struct scsi_device *sdp)
debugfs_remove(devip->debugfs_entry);
- if (sdebug_ptype == TYPE_TAPE) {
+ if (sdp->type == TYPE_TAPE) {
kfree(devip->tape_blocks[0]);
devip->tape_blocks[0] = NULL;
}
@@ -6855,18 +6862,16 @@ static int sdebug_fail_lun_reset(struct scsi_cmnd *cmnd)
static void scsi_tape_reset_clear(struct sdebug_dev_info *devip)
{
- if (sdebug_ptype == TYPE_TAPE) {
- int i;
+ int i;
- devip->tape_blksize = TAPE_DEF_BLKSIZE;
- devip->tape_density = TAPE_DEF_DENSITY;
- devip->tape_partition = 0;
- devip->tape_dce = 0;
- for (i = 0; i < TAPE_MAX_PARTITIONS; i++)
- devip->tape_location[i] = 0;
- devip->tape_pending_nbr_partitions = -1;
- /* Don't reset partitioning? */
- }
+ devip->tape_blksize = TAPE_DEF_BLKSIZE;
+ devip->tape_density = TAPE_DEF_DENSITY;
+ devip->tape_partition = 0;
+ devip->tape_dce = 0;
+ for (i = 0; i < TAPE_MAX_PARTITIONS; i++)
+ devip->tape_location[i] = 0;
+ devip->tape_pending_nbr_partitions = -1;
+ /* Don't reset partitioning? */
}
static int scsi_debug_device_reset(struct scsi_cmnd *SCpnt)
@@ -6884,7 +6889,8 @@ static int scsi_debug_device_reset(struct scsi_cmnd *SCpnt)
scsi_debug_stop_all_queued(sdp);
if (devip) {
set_bit(SDEBUG_UA_POR, devip->uas_bm);
- scsi_tape_reset_clear(devip);
+ if (SCpnt->device->type == TYPE_TAPE)
+ scsi_tape_reset_clear(devip);
}
if (sdebug_fail_lun_reset(SCpnt)) {
@@ -6923,7 +6929,8 @@ static int scsi_debug_target_reset(struct scsi_cmnd *SCpnt)
list_for_each_entry(devip, &sdbg_host->dev_info_list, dev_list) {
if (devip->target == sdp->id) {
set_bit(SDEBUG_UA_BUS_RESET, devip->uas_bm);
- scsi_tape_reset_clear(devip);
+ if (SCpnt->device->type == TYPE_TAPE)
+ scsi_tape_reset_clear(devip);
++k;
}
}
@@ -6955,7 +6962,8 @@ static int scsi_debug_bus_reset(struct scsi_cmnd *SCpnt)
list_for_each_entry(devip, &sdbg_host->dev_info_list, dev_list) {
set_bit(SDEBUG_UA_BUS_RESET, devip->uas_bm);
- scsi_tape_reset_clear(devip);
+ if (SCpnt->device->type == TYPE_TAPE)
+ scsi_tape_reset_clear(devip);
++k;
}
@@ -6979,7 +6987,8 @@ static int scsi_debug_host_reset(struct scsi_cmnd *SCpnt)
list_for_each_entry(devip, &sdbg_host->dev_info_list,
dev_list) {
set_bit(SDEBUG_UA_BUS_RESET, devip->uas_bm);
- scsi_tape_reset_clear(devip);
+ if (SCpnt->device->type == TYPE_TAPE)
+ scsi_tape_reset_clear(devip);
++k;
}
}
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v2 5/5] scsi_scsi_debug: Add ERASE for tapes
2025-03-10 15:55 [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Kai Mäkisara
` (3 preceding siblings ...)
2025-03-10 15:55 ` [PATCH v2 4/5] scsi: scsi_debug: Use scsi_device->type instead os sdebug_ptype where possible Kai Mäkisara
@ 2025-03-10 15:55 ` Kai Mäkisara
2025-04-11 20:23 ` [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Martin K. Petersen
5 siblings, 0 replies; 7+ messages in thread
From: Kai Mäkisara @ 2025-03-10 15:55 UTC (permalink / raw)
To: linux-scsi, dgilbert; +Cc: martin.petersen, James.Bottomley, Kai Mäkisara
The command ERASE (6) for tape devices is added.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi>
---
drivers/scsi/scsi_debug.c | 23 ++++++++++++++++++++---
1 file changed, 20 insertions(+), 3 deletions(-)
diff --git a/drivers/scsi/scsi_debug.c b/drivers/scsi/scsi_debug.c
index e4b336cc0a5f..de91bb18e036 100644
--- a/drivers/scsi/scsi_debug.c
+++ b/drivers/scsi/scsi_debug.c
@@ -528,7 +528,8 @@ enum sdeb_opcode_index {
SDEB_I_WRITE_FILEMARKS = 35,
SDEB_I_SPACE = 36,
SDEB_I_FORMAT_MEDIUM = 37,
- SDEB_I_LAST_ELEM_P1 = 38, /* keep this last (previous + 1) */
+ SDEB_I_ERASE = 38,
+ SDEB_I_LAST_ELEM_P1 = 39, /* keep this last (previous + 1) */
};
@@ -539,7 +540,7 @@ static const unsigned char opcode_ind_arr[256] = {
SDEB_I_READ, 0, SDEB_I_WRITE, 0, 0, 0, 0, 0,
SDEB_I_WRITE_FILEMARKS, SDEB_I_SPACE, SDEB_I_INQUIRY, 0, 0,
SDEB_I_MODE_SELECT, SDEB_I_RESERVE, SDEB_I_RELEASE,
- 0, 0, SDEB_I_MODE_SENSE, SDEB_I_START_STOP, 0, SDEB_I_SEND_DIAG,
+ 0, SDEB_I_ERASE, SDEB_I_MODE_SENSE, SDEB_I_START_STOP, 0, SDEB_I_SEND_DIAG,
SDEB_I_ALLOW_REMOVAL, 0,
/* 0x20; 0x20->0x3f: 10 byte cdbs */
0, 0, 0, 0, 0, SDEB_I_READ_CAPACITY, 0, 0,
@@ -627,6 +628,7 @@ static int resp_space(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_read_position(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_rewind(struct scsi_cmnd *, struct sdebug_dev_info *);
static int resp_format_medium(struct scsi_cmnd *, struct sdebug_dev_info *);
+static int resp_erase(struct scsi_cmnd *, struct sdebug_dev_info *);
static int sdebug_do_add_host(bool mk_new_store);
static int sdebug_add_host_helper(int per_host_idx);
@@ -887,7 +889,9 @@ static const struct opcode_info_t opcode_info_arr[SDEB_I_LAST_ELEM_P1 + 1] = {
{6, 0x07, 0xff, 0xff, 0xff, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
{0, 0x4, 0, DS_SSC, 0, resp_format_medium, NULL, /* FORMAT MEDIUM (6) */
{6, 0x3, 0x7, 0, 0, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
-/* 38 */
+ {0, 0x19, 0, DS_SSC, F_D_IN, resp_erase, NULL, /* ERASE (6) */
+ {6, 0x03, 0x33, 0, 0, 0xc7, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
+/* 39 */
/* sentinel */
{0xff, 0, 0, 0, 0, NULL, NULL, /* terminating element */
{0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} },
@@ -3692,6 +3696,19 @@ static int resp_format_medium(struct scsi_cmnd *scp,
return 0;
}
+static int resp_erase(struct scsi_cmnd *scp,
+ struct sdebug_dev_info *devip)
+{
+ int partition = devip->tape_partition;
+ int pos = devip->tape_location[partition];
+ struct tape_block *blp;
+
+ blp = devip->tape_blocks[partition] + pos;
+ blp->fl_size = TAPE_BLOCK_EOD_FLAG;
+
+ return 0;
+}
+
static inline bool sdebug_dev_is_zoned(struct sdebug_dev_info *devip)
{
return devip->nr_zones != 0;
--
2.43.0
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types
2025-03-10 15:55 [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Kai Mäkisara
` (4 preceding siblings ...)
2025-03-10 15:55 ` [PATCH v2 5/5] scsi_scsi_debug: Add ERASE for tapes Kai Mäkisara
@ 2025-04-11 20:23 ` Martin K. Petersen
5 siblings, 0 replies; 7+ messages in thread
From: Martin K. Petersen @ 2025-04-11 20:23 UTC (permalink / raw)
To: Kai Mäkisara; +Cc: linux-scsi, dgilbert, martin.petersen, James.Bottomley
Kai,
> The patch set includes changes to better support different device
> types.
Thanks for doing this! Applied to 6.16/scsi-staging.
--
Martin K. Petersen
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2025-04-11 20:23 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-03-10 15:55 [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 1/5] scsi: scsi_debug: Fix two typos in command definitions Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 2/5] scsi: scsi_debug: Enable different command definitions for different device types Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 3/5] scsi: scsi_debug: Move some tape-specific commands to separate definitions Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 4/5] scsi: scsi_debug: Use scsi_device->type instead os sdebug_ptype where possible Kai Mäkisara
2025-03-10 15:55 ` [PATCH v2 5/5] scsi_scsi_debug: Add ERASE for tapes Kai Mäkisara
2025-04-11 20:23 ` [PATCH v2 0/5] scsi: scsi_debug: Changes to improve support for device types Martin K. Petersen
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox