Re: [PATCH v3 4/4] arm64: dts: S32G3: Introduce device tree for S32G-VNP-RDB3

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 21/03/2024 16:41, Wadim Mueller wrote:
> This commit adds device tree support for the NXP S32G3-based
> S32G-VNP-RDB3 Board [1].
> 
> The S32G3 features an 8-core ARM Cortex-A53 based SoC developed by NXP.

...

> +
> +		cpu7: cpu@103 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a53";
> +			reg = <0x103>;
> +			enable-method = "psci";
> +			clocks = <&dfs 0>;
> +		};
> +	};
> +
> +	pmu {

Please order things alphabetically. See DTS coding style.

> +		compatible = "arm,cortex-a53-pmu";
> +		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* sec-phys */
> +			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* phys */
> +			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* virt */
> +			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>, /* hyp-phys */
> +			     <GIC_PPI 12 IRQ_TYPE_LEVEL_LOW>; /* hyp-virt */
> +		arm,no-tick-in-suspend;
> +	};
> +
> +	reserved-memory  {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		scmi_shmem: shm@d0000000 {
> +			compatible = "arm,scmi-shmem";
> +			reg = <0x0 0xd0000000 0x0 0x80>;
> +			no-map;
> +		};
> +	};
> +
> +	firmware {
> +		scmi: scmi {
> +			compatible = "arm,scmi-smc";
> +			shmem = <&scmi_shmem>;
> +			arm,smc-id = <0xc20000fe>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			dfs: protocol@13 {
> +				reg = <0x13>;
> +				#clock-cells = <1>;
> +			};
> +
> +			clks: protocol@14 {
> +				reg = <0x14>;
> +				#clock-cells = <1>;
> +			};
> +		};
> +
> +		psci: psci {
> +			compatible = "arm,psci-1.0";
> +			method = "smc";
> +		};
> +	};
> +
> +	soc@0 {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0 0 0x80000000>;
> +
> +		uart0: serial@401c8000 {
> +			compatible = "nxp,s32g3-linflexuart",
> +				     "fsl,s32v234-linflexuart";
> +			reg = <0x401c8000 0x3000>;
> +			interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>;
> +			status = "disabled";
> +		};
> +
> +		uart1: serial@401cc000 {
> +			compatible = "nxp,s32g3-linflexuart",
> +				     "fsl,s32v234-linflexuart";
> +			reg = <0x401cc000 0x3000>;
> +			interrupts = <GIC_SPI 83 IRQ_TYPE_EDGE_RISING>;
> +			status = "disabled";
> +		};
> +
> +		uart2: serial@402bc000 {
> +			compatible = "nxp,s32g3-linflexuart",
> +				     "fsl,s32v234-linflexuart";
> +			reg = <0x402bc000 0x3000>;
> +			interrupts = <GIC_SPI 84 IRQ_TYPE_EDGE_RISING>;
> +			status = "disabled";
> +		};
> +
> +		gic: interrupt-controller@50800000 {
> +			compatible = "arm,gic-v3";
> +			#interrupt-cells = <3>;
> +			interrupt-controller;
> +			reg = <0x50800000 0x10000>,
> +			      <0x50900000 0x200000>,
> +			      <0x50400000 0x2000>,
> +			      <0x50410000 0x2000>,
> +			      <0x50420000 0x2000>;
> +			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		usdhc0: mmc@402f0000 {

Keep ordered by unit address.



Best regards,
Krzysztof