* Re: [PATCH v5 0/7] add virt-dma support for imx-sdma
From: Sascha Hauer @ 2018-06-22 6:14 UTC (permalink / raw)
To: Robin Gong
Cc: vkoul, l.stach, dan.j.williams, gregkh, jslaby, linux-serial,
dmaengine, linux-kernel, linux-arm-kernel, linux-imx
In-Reply-To: <1529427424-12321-1-git-send-email-yibin.gong@nxp.com>
On Wed, Jun 20, 2018 at 12:56:57AM +0800, Robin Gong wrote:
> Robin Gong (6):
> tty: serial: imx: correct dma cookie status
> dmaengine: imx-sdma: add virt-dma support
> dmaengine: imx-sdma: remove useless 'lock' and 'enabled' in 'struct
> sdma_channel'
> dmaengine: imx-sdma: remove the maximum limitation for bd numbers
> dmaengine: imx-sdma: add sdma_transfer_init to decrease code overlap
> dmaengine: imx-sdma: alloclate bd memory from dma pool
>
> Sascha Hauer (1):
> dmaengine: imx-sdma: factor out a struct sdma_desc from struct
> sdma_channel
>From my side you can get my
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
for this series, but of course it would be nice to get the feedback from
Lucas.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
^ permalink raw reply
* Re: [RFC][PATCH 0/6] Use printk_safe context for TTY and UART port locks
From: Alan Cox @ 2018-06-22 16:21 UTC (permalink / raw)
To: Linus Torvalds
Cc: Steven Rostedt, Petr Mladek, Sergey Senozhatsky,
Greg Kroah-Hartman, Jiri Slaby, Peter Zijlstra, Andrew Morton,
Dmitry Vyukov, Linux Kernel Mailing List, linux-serial,
SergeySenozhatsky
In-Reply-To: <CA+55aFwpcbNO6FS4=O-BrsC4vMBaT3JeFG-_D9WtgmW+Dof3iA@mail.gmail.com>
On Wed, 20 Jun 2018 11:44:13 +0900
Linus Torvalds <torvalds@linux-foundation.org> wrote:
> On Wed, Jun 20, 2018 at 11:34 AM Steven Rostedt <rostedt@goodmis.org> wrote:
> >
> > Perhaps we should do an audit of the console drivers and remove all
> > printk, pr_* , WARN*, BUG* from them.
>
> Only the actual _printing_ parts.
No because they are normally rather useful because that port isn't the
console. If you trylock it as I suggested then at least you'd just drop
the recursive cases and get messages otherwise.
Really that's all that you need - log the message to whichever console
targets you can currently safely do so. If it's none well there was
always the proposed morse code keyboard light driver 8)
Alan
^ permalink raw reply
* Re: [RFC][PATCH 0/6] Use printk_safe context for TTY and UART port locks
From: Peter Zijlstra @ 2018-06-22 16:39 UTC (permalink / raw)
To: Alan Cox
Cc: Linus Torvalds, Steven Rostedt, Petr Mladek, Sergey Senozhatsky,
Greg Kroah-Hartman, Jiri Slaby, Andrew Morton, Dmitry Vyukov,
Linux Kernel Mailing List, linux-serial, SergeySenozhatsky
In-Reply-To: <20180622172100.2293b5e5@alans-desktop>
On Fri, Jun 22, 2018 at 05:21:00PM +0100, Alan Cox wrote:
> Really that's all that you need - log the message to whichever console
> targets you can currently safely do so. If it's none well there was
> always the proposed morse code keyboard light driver 8)
Only if your keyboard still has blinky lights on.. (mine doesn't)
^ permalink raw reply
* Re: [RFC][PATCH 0/6] Use printk_safe context for TTY and UART port locks
From: Sergey Senozhatsky @ 2018-06-23 5:21 UTC (permalink / raw)
To: Alan Cox
Cc: Linus Torvalds, Steven Rostedt, Petr Mladek, Sergey Senozhatsky,
Greg Kroah-Hartman, Jiri Slaby, Peter Zijlstra, Andrew Morton,
Dmitry Vyukov, Linux Kernel Mailing List, linux-serial,
SergeySenozhatsky
In-Reply-To: <20180622172100.2293b5e5@alans-desktop>
On (06/22/18 17:21), Alan Cox wrote:
> On Wed, 20 Jun 2018 11:44:13 +0900
> Linus Torvalds <torvalds@linux-foundation.org> wrote:
>
> > On Wed, Jun 20, 2018 at 11:34 AM Steven Rostedt <rostedt@goodmis.org> wrote:
> > >
> > > Perhaps we should do an audit of the console drivers and remove all
> > > printk, pr_* , WARN*, BUG* from them.
> >
> > Only the actual _printing_ parts.
>
> No because they are normally rather useful because that port isn't the
> console. If you trylock
trylock is boring, me wants printk_safe_mask everywhere :)
> Really that's all that you need - log the message to whichever console
> targets you can currently safely do so. If it's none well there was
> always the proposed morse code keyboard light driver 8)
Hm, just discard messages? With printk_safe_mask we keep everything
in a lockless per-CPU buffer, which we flush [per-CPU buffer -> printk logbuf]
from irq_work, so we can print it later.
-ss
^ permalink raw reply
* [PATCH] dt-bindings: serial: imx: clarify rs485 support usage
From: Baruch Siach @ 2018-06-25 7:33 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, Greg Kroah-Hartman
Cc: Baruch Siach, linux-serial, linux-arm-kernel,
Uwe Kleine-König
The i.MX UART peripheral uses the RST_B signal as input, and CTS_B as
output. This is just like the CDE role in RS-232. This is true
regardless of the "DTE mode" setting of this peripheral.
As a result, rs485 support hardware must use the CTS_B signal to control
the RS-485 transceiver. This is in contrast to generic rs485 kernel
code, documentation, and DT property names that consistently refer to
the RST as transceiver control signal.
Add a note in the DT binding document about that, to reduce the
confusion somewhat.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
---
Documentation/devicetree/bindings/serial/fsl-imx-uart.txt | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
index afcfbc34e243..35957cbf1571 100644
--- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
+++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
@@ -9,7 +9,11 @@ Optional properties:
- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
in DCE mode by default.
- rs485-rts-delay, rs485-rts-active-low, rs485-rx-during-tx,
- linux,rs485-enabled-at-boot-time: see rs485.txt
+ linux,rs485-enabled-at-boot-time: see rs485.txt. Note that for RS485
+ you must enable either the "uart-has-rtscts" or the "rts-gpios"
+ properties. In case you use "uart-has-rtscts" the signal that controls
+ the transceiver is actually CTS_B, not RTS_B. CTS_B is always output,
+ and RTS_B is input, regardless of dte-mode.
Please check Documentation/devicetree/bindings/serial/serial.txt
for the complete list of generic properties.
--
2.18.0
^ permalink raw reply related
* Re: [PATCH] dt-bindings: serial: imx: clarify rs485 support usage
From: Lothar Waßmann @ 2018-06-25 8:16 UTC (permalink / raw)
To: Baruch Siach
Cc: linux-serial, Greg Kroah-Hartman, Sascha Hauer, NXP Linux Team,
Pengutronix Kernel Team, Uwe Kleine-König, Fabio Estevam,
Shawn Guo, linux-arm-kernel
In-Reply-To: <01fc1e3d89037adce38177c3922d277584214fdd.1529911999.git.baruch@tkos.co.il>
Hi,
On Mon, 25 Jun 2018 10:33:19 +0300 Baruch Siach wrote:
> The i.MX UART peripheral uses the RST_B signal as input, and CTS_B as
> output. This is just like the CDE role in RS-232. This is true
>
s/CDE/DCE/
> regardless of the "DTE mode" setting of this peripheral.
>
> As a result, rs485 support hardware must use the CTS_B signal to control
> the RS-485 transceiver. This is in contrast to generic rs485 kernel
> code, documentation, and DT property names that consistently refer to
> the RST as transceiver control signal.
>
s/RST/RTS/
> Add a note in the DT binding document about that, to reduce the
> confusion somewhat.
>
> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
> ---
> Documentation/devicetree/bindings/serial/fsl-imx-uart.txt | 6 +++++-
> 1 file changed, 5 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
> index afcfbc34e243..35957cbf1571 100644
> --- a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
> +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt
> @@ -9,7 +9,11 @@ Optional properties:
> - fsl,dte-mode : Indicate the uart works in DTE mode. The uart works
> in DCE mode by default.
> - rs485-rts-delay, rs485-rts-active-low, rs485-rx-during-tx,
> - linux,rs485-enabled-at-boot-time: see rs485.txt
> + linux,rs485-enabled-at-boot-time: see rs485.txt. Note that for RS485
> + you must enable either the "uart-has-rtscts" or the "rts-gpios"
> + properties. In case you use "uart-has-rtscts" the signal that controls
> + the transceiver is actually CTS_B, not RTS_B. CTS_B is always output,
> + and RTS_B is input, regardless of dte-mode.
>
> Please check Documentation/devicetree/bindings/serial/serial.txt
> for the complete list of generic properties.
Lothar Waßmann
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply
* [PATCH v9 0/6] Driver for at91 usart in spi mode
From: Radu Pirea @ 2018-06-25 10:20 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
Hello,
This is the second version of driver. I added a mfd driver which by
default probes atmel_serial driver and if in dt is specified to probe
the spi driver, then the spi-at91-usart driver will be probed. The
compatible for atmel_serial is now the compatible for at91-usart mfd
driver and compatilbe for atmel_serial driver was changed in order to
keep the bindings for serial as they are.
Changes in v9:
- minor changes
- rebased on top of broonie/for-4.19
Changes in v8:
- fixed passing an empty mfd cell if "atmel,usart-mode" value is invalid
Changes in v7:
- synced up SPDIX license with module license
- numbering of usart modes starts from 0 insteand of 1
Changes in v6:
- removed unused compatible strings from serial and spi drivers
Changes in v5:
- fixed usage of stdout-path property with atmel_serial driver
Changes in v4:
- modified the spi driver to use cs gpio support form spi subsystem
- fixed dma transfers for serial driver
- squashed binding for spi and serial and moved them to mfd/atmel-usart.txt
Changes in v3:
- fixed spi slaves probing
Changes in v2:
- added at91-usart mfd driver
- modified spi-at91-usart driver to work as mfd driver child
- modified atmel_serial driver to work as mfd driver child
Changes in v1:
- added spi-at91-usart driver
Radu Pirea (6):
MAINTAINERS: add at91 usart mfd driver
dt-bindings: add binding for atmel-usart in SPI mode
mfd: at91-usart: added mfd driver for usart
MAINTAINERS: add at91 usart spi driver
spi: at91-usart: add driver for at91-usart as spi
tty/serial: atmel: change the driver to work under at91-usart mfd
.../bindings/{serial => mfd}/atmel-usart.txt | 25 +-
MAINTAINERS | 16 +
drivers/mfd/Kconfig | 9 +
drivers/mfd/Makefile | 1 +
drivers/mfd/at91-usart.c | 71 +++
drivers/spi/Kconfig | 9 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-at91-usart.c | 432 ++++++++++++++++++
drivers/tty/serial/Kconfig | 1 +
drivers/tty/serial/atmel_serial.c | 42 +-
include/dt-bindings/mfd/at91-usart.h | 17 +
11 files changed, 607 insertions(+), 17 deletions(-)
rename Documentation/devicetree/bindings/{serial => mfd}/atmel-usart.txt (76%)
create mode 100644 drivers/mfd/at91-usart.c
create mode 100644 drivers/spi/spi-at91-usart.c
create mode 100644 include/dt-bindings/mfd/at91-usart.h
--
2.17.1
^ permalink raw reply
* [PATCH v9 1/6] MAINTAINERS: add at91 usart mfd driver
From: Radu Pirea @ 2018-06-25 10:21 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625102105.28383-1-radu.pirea@microchip.com>
Added entry for at91 usart mfd driver.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
---
MAINTAINERS | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 9d5eeff51b5f..7ac6e6af5292 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9321,6 +9321,7 @@ M: Richard Genoud <richard.genoud@gmail.com>
S: Maintained
F: drivers/tty/serial/atmel_serial.c
F: drivers/tty/serial/atmel_serial.h
+F: Documentation/devicetree/bindings/mfd/atmel-usart.txt
MICROCHIP / ATMEL DMA DRIVER
M: Ludovic Desroches <ludovic.desroches@microchip.com>
@@ -9353,6 +9354,14 @@ S: Supported
F: drivers/mtd/nand/raw/atmel/*
F: Documentation/devicetree/bindings/mtd/atmel-nand.txt
+MICROCHIP AT91 USART MFD DRIVER
+M: Radu Pirea <radu.pirea@microchip.com>
+L: linux-kernel@vger.kernel.org
+S: Supported
+F: drivers/mfd/at91-usart.c
+F: include/dt-bindings/mfd/at91-usart.h
+F: Documentation/devicetree/bindings/mfd/atmel-usart.txt
+
MICROCHIP KSZ SERIES ETHERNET SWITCH DRIVER
M: Woojung Huh <Woojung.Huh@microchip.com>
M: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
--
2.17.1
^ permalink raw reply related
* [PATCH v9 2/6] dt-bindings: add binding for atmel-usart in SPI mode
From: Radu Pirea @ 2018-06-25 10:21 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625102105.28383-1-radu.pirea@microchip.com>
This patch moves the bindings for serial from serial/atmel-usart.txt to
mfd/atmel-usart.txt and adds bindings for USART in SPI mode.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../bindings/{serial => mfd}/atmel-usart.txt | 25 +++++++++++++++++--
include/dt-bindings/mfd/at91-usart.h | 17 +++++++++++++
2 files changed, 40 insertions(+), 2 deletions(-)
rename Documentation/devicetree/bindings/{serial => mfd}/atmel-usart.txt (76%)
create mode 100644 include/dt-bindings/mfd/at91-usart.h
diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
similarity index 76%
rename from Documentation/devicetree/bindings/serial/atmel-usart.txt
rename to Documentation/devicetree/bindings/mfd/atmel-usart.txt
index 7c0d6b2f53e4..0348fef0f497 100644
--- a/Documentation/devicetree/bindings/serial/atmel-usart.txt
+++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
@@ -1,6 +1,6 @@
* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART)
-Required properties:
+Required properties for USART:
- compatible: Should be "atmel,<chip>-usart" or "atmel,<chip>-dbgu"
The compatible <chip> indicated will be the first SoC to support an
additional mode or an USART new feature.
@@ -11,7 +11,13 @@ Required properties:
Required elements: "usart"
- clocks: phandles to input clocks.
-Optional properties:
+Required properties for USART in SPI mode:
+- #size-cells : Must be <0>
+- #address-cells : Must be <1>
+- cs-gpios: chipselects (internal cs not supported)
+- atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h)
+
+Optional properties in serial mode:
- atmel,use-dma-rx: use of PDC or DMA for receiving data
- atmel,use-dma-tx: use of PDC or DMA for transmitting data
- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively.
@@ -62,3 +68,18 @@ Example:
dma-names = "tx", "rx";
atmel,fifo-size = <32>;
};
+
+- SPI mode:
+ #include <dt-bindings/mfd/at91-usart.h>
+
+ spi0: spi@f001c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-usart", "atmel,at91sam9260-usart";
+ atmel,usart-mode = <AT91_USART_MODE_SPI>;
+ reg = <0xf001c000 0x100>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usart0_clk>;
+ clock-names = "usart";
+ cs-gpios = <&pioB 3 0>;
+ };
diff --git a/include/dt-bindings/mfd/at91-usart.h b/include/dt-bindings/mfd/at91-usart.h
new file mode 100644
index 000000000000..2de5bc312e1e
--- /dev/null
+++ b/include/dt-bindings/mfd/at91-usart.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides macros for AT91 USART DT bindings.
+ *
+ * Copyright (C) 2018 Microchip Technology
+ *
+ * Author: Radu Pirea <radu.pirea@microchip.com>
+ *
+ */
+
+#ifndef __DT_BINDINGS_AT91_USART_H__
+#define __DT_BINDINGS_AT91_USART_H__
+
+#define AT91_USART_MODE_SERIAL 0
+#define AT91_USART_MODE_SPI 1
+
+#endif /* __DT_BINDINGS_AT91_USART_H__ */
--
2.17.1
^ permalink raw reply related
* [PATCH v9 3/6] mfd: at91-usart: added mfd driver for usart
From: Radu Pirea @ 2018-06-25 10:21 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625102105.28383-1-radu.pirea@microchip.com>
This mfd driver is just a wrapper over atmel_serial driver and
spi-at91-usart driver. Selection of one of the drivers is based on a
property from device tree. If the property is not specified, the default
driver is atmel_serial.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
---
drivers/mfd/Kconfig | 9 +++++
drivers/mfd/Makefile | 1 +
drivers/mfd/at91-usart.c | 71 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 81 insertions(+)
create mode 100644 drivers/mfd/at91-usart.c
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b860eb5aa194..a886672b960d 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -99,6 +99,15 @@ config MFD_AAT2870_CORE
additional drivers must be enabled in order to use the
functionality of the device.
+config MFD_AT91_USART
+ tristate "AT91 USART Driver"
+ select MFD_CORE
+ help
+ Select this to get support for AT91 USART IP. This is a wrapper
+ over at91-usart-serial driver and usart-spi-driver. Only one function
+ can be used at a time. The choice is done at boot time by the probe
+ function of this MFD driver according to a device tree property.
+
config MFD_ATMEL_FLEXCOM
tristate "Atmel Flexcom (Flexible Serial Communication Unit)"
select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index e9fd20dba18d..c7e66928abb9 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -184,6 +184,7 @@ obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o
obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
obj-$(CONFIG_MFD_TPS65090) += tps65090.o
obj-$(CONFIG_MFD_AAT2870_CORE) += aat2870-core.o
+obj-$(CONFIG_MFD_AT91_USART) += at91-usart.o
obj-$(CONFIG_MFD_ATMEL_FLEXCOM) += atmel-flexcom.o
obj-$(CONFIG_MFD_ATMEL_HLCDC) += atmel-hlcdc.o
obj-$(CONFIG_MFD_ATMEL_SMC) += atmel-smc.o
diff --git a/drivers/mfd/at91-usart.c b/drivers/mfd/at91-usart.c
new file mode 100644
index 000000000000..a4b9929c156f
--- /dev/null
+++ b/drivers/mfd/at91-usart.c
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for AT91 USART
+ *
+ * Copyright (C) 2018 Microchip Technology
+ *
+ * Author: Radu Pirea <radu.pirea@microchip.com>
+ *
+ */
+
+#include <dt-bindings/mfd/at91-usart.h>
+
+#include <linux/module.h>
+#include <linux/mfd/core.h>
+#include <linux/property.h>
+
+static struct mfd_cell at91_usart_spi_subdev = {
+ .name = "at91_usart_spi",
+ .of_compatible = "microchip,at91sam9g45-usart-spi",
+ };
+
+static struct mfd_cell at91_usart_serial_subdev = {
+ .name = "atmel_usart_serial",
+ .of_compatible = "atmel,at91rm9200-usart-serial",
+ };
+
+static int at91_usart_mode_probe(struct platform_device *pdev)
+{
+ struct mfd_cell cell;
+ u32 opmode = AT91_USART_MODE_SERIAL;
+
+ device_property_read_u32(&pdev->dev, "atmel,usart-mode", &opmode);
+
+ switch (opmode) {
+ case AT91_USART_MODE_SPI:
+ cell = at91_usart_spi_subdev;
+ break;
+ case AT91_USART_MODE_SERIAL:
+ cell = at91_usart_serial_subdev;
+ break;
+ default:
+ dev_err(&pdev->dev, "atmel,usart-mode has an invalid value %u\n",
+ opmode);
+ return -EINVAL;
+ }
+
+ return devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_AUTO, &cell, 1,
+ NULL, 0, NULL);
+}
+
+static const struct of_device_id at91_usart_mode_of_match[] = {
+ { .compatible = "atmel,at91rm9200-usart" },
+ { .compatible = "atmel,at91sam9260-usart" },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, at91_usart_mode_of_match);
+
+static struct platform_driver at91_usart_mfd = {
+ .probe = at91_usart_mode_probe,
+ .driver = {
+ .name = "at91_usart_mode",
+ .of_match_table = at91_usart_mode_of_match,
+ },
+};
+
+module_platform_driver(at91_usart_mfd);
+
+MODULE_AUTHOR("Radu Pirea <radu.pirea@microchip.com>");
+MODULE_DESCRIPTION("AT91 USART MFD driver");
+MODULE_LICENSE("GPL v2");
--
2.17.1
^ permalink raw reply related
* [PATCH v9 4/6] MAINTAINERS: add at91 usart spi driver
From: Radu Pirea @ 2018-06-25 10:21 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625102105.28383-1-radu.pirea@microchip.com>
Added entry for at91 usart mfd driver.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
---
MAINTAINERS | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 7ac6e6af5292..f849cc4acbf6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9362,6 +9362,13 @@ F: drivers/mfd/at91-usart.c
F: include/dt-bindings/mfd/at91-usart.h
F: Documentation/devicetree/bindings/mfd/atmel-usart.txt
+MICROCHIP AT91 USART SPI DRIVER
+M: Radu Pirea <radu.pirea@microchip.com>
+L: linux-spi@vger.kernel.org
+S: Supported
+F: drivers/spi/spi-at91-usart.c
+F: Documentation/devicetree/bindings/mfd/atmel-usart.txt
+
MICROCHIP KSZ SERIES ETHERNET SWITCH DRIVER
M: Woojung Huh <Woojung.Huh@microchip.com>
M: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
--
2.17.1
^ permalink raw reply related
* [PATCH v9 5/6] spi: at91-usart: add driver for at91-usart as spi
From: Radu Pirea @ 2018-06-25 10:21 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625102105.28383-1-radu.pirea@microchip.com>
This is the driver for at91-usart in spi mode. The USART IP can be configured
to work in many modes and one of them is SPI.
The driver was tested on sama5d3-xplained and sama5d4-xplained boards with
enc28j60 ethernet controller as slave.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
---
drivers/spi/Kconfig | 9 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-at91-usart.c | 432 +++++++++++++++++++++++++++++++++++
3 files changed, 442 insertions(+)
create mode 100644 drivers/spi/spi-at91-usart.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index ad5d68e1dab7..02bb35057ccd 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -83,6 +83,15 @@ config SPI_ATMEL
This selects a driver for the Atmel SPI Controller, present on
many AT91 ARM chips.
+config SPI_AT91_USART
+ tristate "Atmel USART Controller SPI driver"
+ depends on HAS_DMA
+ depends on (ARCH_AT91 || COMPILE_TEST)
+ select MFD_AT91_USART
+ help
+ This selects a driver for the AT91 USART Controller as SPI Master,
+ present on AT91 and SAMA5 SoC series.
+
config SPI_AU1550
tristate "Au1550/Au1200/Au1300 SPI Controller"
depends on MIPS_ALCHEMY
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index cb1f4378b87c..901ff606e6e5 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_SPI_LOOPBACK_TEST) += spi-loopback-test.o
obj-$(CONFIG_SPI_ALTERA) += spi-altera.o
obj-$(CONFIG_SPI_ARMADA_3700) += spi-armada-3700.o
obj-$(CONFIG_SPI_ATMEL) += spi-atmel.o
+obj-$(CONFIG_SPI_AT91_USART) += spi-at91-usart.o
obj-$(CONFIG_SPI_ATH79) += spi-ath79.o
obj-$(CONFIG_SPI_AU1550) += spi-au1550.o
obj-$(CONFIG_SPI_AXI_SPI_ENGINE) += spi-axi-spi-engine.o
diff --git a/drivers/spi/spi-at91-usart.c b/drivers/spi/spi-at91-usart.c
new file mode 100644
index 000000000000..0f92c02bf104
--- /dev/null
+++ b/drivers/spi/spi-at91-usart.c
@@ -0,0 +1,432 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for AT91 USART Controllers as SPI
+ *
+ * Copyright (C) 2018 Microchip Technology Inc.
+ * Author: Radu Pirea <radu.pirea@microchip.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+
+#include <linux/spi/spi.h>
+
+#define US_CR 0x00
+#define US_MR 0x04
+#define US_IER 0x08
+#define US_IDR 0x0C
+#define US_CSR 0x14
+#define US_RHR 0x18
+#define US_THR 0x1C
+#define US_BRGR 0x20
+#define US_VERSION 0xFC
+
+#define US_CR_RSTRX BIT(2)
+#define US_CR_RSTTX BIT(3)
+#define US_CR_RXEN BIT(4)
+#define US_CR_RXDIS BIT(5)
+#define US_CR_TXEN BIT(6)
+#define US_CR_TXDIS BIT(7)
+
+#define US_MR_SPI_MASTER 0x0E
+#define US_MR_CHRL GENMASK(7, 6)
+#define US_MR_CPHA BIT(8)
+#define US_MR_CPOL BIT(16)
+#define US_MR_CLKO BIT(18)
+#define US_MR_WRDBT BIT(20)
+#define US_MR_LOOP BIT(15)
+
+#define US_IR_RXRDY BIT(0)
+#define US_IR_TXRDY BIT(1)
+#define US_IR_OVRE BIT(5)
+
+#define US_BRGR_SIZE BIT(16)
+
+#define US_MIN_CLK_DIV 0x06
+#define US_MAX_CLK_DIV BIT(16)
+
+#define US_RESET (US_CR_RSTRX | US_CR_RSTTX)
+#define US_DISABLE (US_CR_RXDIS | US_CR_TXDIS)
+#define US_ENABLE (US_CR_RXEN | US_CR_TXEN)
+#define US_OVRE_RXRDY_IRQS (US_IR_OVRE | US_IR_RXRDY)
+
+#define US_INIT \
+ (US_MR_SPI_MASTER | US_MR_CHRL | US_MR_CLKO | US_MR_WRDBT)
+
+/* Register access macros */
+#define at91_usart_spi_readl(port, reg) \
+ readl_relaxed((port)->regs + US_##reg)
+#define at91_usart_spi_writel(port, reg, value) \
+ writel_relaxed((value), (port)->regs + US_##reg)
+
+#define at91_usart_spi_readb(port, reg) \
+ readb_relaxed((port)->regs + US_##reg)
+#define at91_usart_spi_writeb(port, reg, value) \
+ writeb_relaxed((value), (port)->regs + US_##reg)
+
+struct at91_usart_spi {
+ struct spi_transfer *current_transfer;
+ void __iomem *regs;
+ struct device *dev;
+ struct clk *clk;
+
+ /*used in interrupt to protect data reading*/
+ spinlock_t lock;
+
+ int irq;
+ unsigned int current_tx_remaining_bytes;
+ unsigned int current_rx_remaining_bytes;
+
+ u32 spi_clk;
+ u32 status;
+
+ bool xfer_failed;
+};
+
+static inline u32 at91_usart_spi_tx_ready(struct at91_usart_spi *aus)
+{
+ return aus->status & US_IR_TXRDY;
+}
+
+static inline u32 at91_usart_spi_rx_ready(struct at91_usart_spi *aus)
+{
+ return aus->status & US_IR_RXRDY;
+}
+
+static inline u32 at91_usart_spi_check_overrun(struct at91_usart_spi *aus)
+{
+ return aus->status & US_IR_OVRE;
+}
+
+static inline u32 at91_usart_spi_read_status(struct at91_usart_spi *aus)
+{
+ aus->status = at91_usart_spi_readl(aus, CSR);
+ return aus->status;
+}
+
+static inline void at91_usart_spi_tx(struct at91_usart_spi *aus)
+{
+ unsigned int len = aus->current_transfer->len;
+ unsigned int remaining = aus->current_tx_remaining_bytes;
+ const u8 *tx_buf = aus->current_transfer->tx_buf;
+
+ if (!remaining)
+ return;
+
+ if (at91_usart_spi_tx_ready(aus)) {
+ at91_usart_spi_writeb(aus, THR, tx_buf[len - remaining]);
+ aus->current_tx_remaining_bytes--;
+ }
+}
+
+static inline void at91_usart_spi_rx(struct at91_usart_spi *aus)
+{
+ int len = aus->current_transfer->len;
+ int remaining = aus->current_rx_remaining_bytes;
+ u8 *rx_buf = aus->current_transfer->rx_buf;
+
+ if (!remaining)
+ return;
+
+ rx_buf[len - remaining] = at91_usart_spi_readb(aus, RHR);
+ aus->current_rx_remaining_bytes--;
+}
+
+static inline void
+at91_usart_spi_set_xfer_speed(struct at91_usart_spi *aus,
+ struct spi_transfer *xfer)
+{
+ at91_usart_spi_writel(aus, BRGR,
+ DIV_ROUND_UP(aus->spi_clk, xfer->speed_hz));
+}
+
+static irqreturn_t at91_usart_spi_interrupt(int irq, void *dev_id)
+{
+ struct spi_controller *controller = dev_id;
+ struct at91_usart_spi *aus = spi_master_get_devdata(controller);
+
+ spin_lock(&aus->lock);
+ at91_usart_spi_read_status(aus);
+
+ if (at91_usart_spi_check_overrun(aus)) {
+ aus->xfer_failed = true;
+ at91_usart_spi_writel(aus, IDR, US_IR_OVRE | US_IR_RXRDY);
+ spin_unlock(&aus->lock);
+ return IRQ_HANDLED;
+ }
+
+ if (at91_usart_spi_rx_ready(aus)) {
+ at91_usart_spi_rx(aus);
+ spin_unlock(&aus->lock);
+ return IRQ_HANDLED;
+ }
+
+ spin_unlock(&aus->lock);
+
+ return IRQ_NONE;
+}
+
+static int at91_usart_spi_setup(struct spi_device *spi)
+{
+ struct at91_usart_spi *aus = spi_master_get_devdata(spi->controller);
+ u32 *ausd = spi->controller_state;
+ unsigned int mr = at91_usart_spi_readl(aus, MR);
+ u8 bits = spi->bits_per_word;
+
+ if (bits != 8) {
+ dev_dbg(&spi->dev, "Only 8 bits per word are supported\n");
+ return -EINVAL;
+ }
+
+ if (spi->mode & SPI_CPOL)
+ mr |= US_MR_CPOL;
+ else
+ mr &= ~US_MR_CPOL;
+
+ if (spi->mode & SPI_CPHA)
+ mr |= US_MR_CPHA;
+ else
+ mr &= ~US_MR_CPHA;
+
+ if (spi->mode & SPI_LOOP)
+ mr |= US_MR_LOOP;
+ else
+ mr &= ~US_MR_LOOP;
+
+ if (!ausd) {
+ ausd = kzalloc(sizeof(*ausd), GFP_KERNEL);
+ if (!ausd)
+ return -ENOMEM;
+
+ spi->controller_state = ausd;
+ }
+
+ *ausd = mr;
+
+ dev_dbg(&spi->dev,
+ "setup: bpw %u mode 0x%x -> mr %d %08x\n",
+ bits, spi->mode, spi->chip_select, mr);
+
+ return 0;
+}
+
+int at91_usart_spi_transfer_one(struct spi_controller *ctlr,
+ struct spi_device *spi,
+ struct spi_transfer *xfer)
+{
+ struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+
+ at91_usart_spi_set_xfer_speed(aus, xfer);
+ aus->xfer_failed = false;
+ aus->current_transfer = xfer;
+ aus->current_tx_remaining_bytes = xfer->len;
+ aus->current_rx_remaining_bytes = xfer->len;
+
+ while ((aus->current_tx_remaining_bytes ||
+ aus->current_rx_remaining_bytes) && !aus->xfer_failed) {
+ at91_usart_spi_read_status(aus);
+ at91_usart_spi_tx(aus);
+ cpu_relax();
+ }
+
+ if (aus->xfer_failed) {
+ dev_err(aus->dev, "Overrun!\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
+int at91_usart_spi_prepare_message(struct spi_controller *ctlr,
+ struct spi_message *message)
+{
+ struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+ struct spi_device *spi = message->spi;
+ u32 *ausd = spi->controller_state;
+
+ at91_usart_spi_writel(aus, CR, US_ENABLE);
+ at91_usart_spi_writel(aus, IER, US_OVRE_RXRDY_IRQS);
+ at91_usart_spi_writel(aus, MR, *ausd);
+
+ return 0;
+}
+
+int at91_usart_spi_unprepare_message(struct spi_controller *ctlr,
+ struct spi_message *message)
+{
+ struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+
+ at91_usart_spi_writel(aus, CR, US_RESET | US_DISABLE);
+ at91_usart_spi_writel(aus, IDR, US_OVRE_RXRDY_IRQS);
+
+ return 0;
+}
+
+static void at91_usart_spi_cleanup(struct spi_device *spi)
+{
+ struct at91_usart_spi_device *ausd = spi->controller_state;
+
+ spi->controller_state = NULL;
+ kfree(ausd);
+}
+
+static void at91_usart_spi_init(struct at91_usart_spi *aus)
+{
+ at91_usart_spi_writel(aus, MR, US_INIT);
+ at91_usart_spi_writel(aus, CR, US_RESET | US_DISABLE);
+}
+
+static int at91_usart_gpio_setup(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.parent->of_node;
+ int i;
+ int ret;
+ int nb;
+
+ if (!np)
+ return -EINVAL;
+
+ nb = of_gpio_named_count(np, "cs-gpios");
+ for (i = 0; i < nb; i++) {
+ int cs_gpio = of_get_named_gpio(np, "cs-gpios", i);
+
+ if (cs_gpio < 0)
+ return cs_gpio;
+
+ if (gpio_is_valid(cs_gpio)) {
+ ret = devm_gpio_request_one(&pdev->dev, cs_gpio,
+ GPIOF_DIR_OUT,
+ dev_name(&pdev->dev));
+ if (ret)
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int at91_usart_spi_probe(struct platform_device *pdev)
+{
+ struct resource *regs;
+ struct spi_controller *controller;
+ struct at91_usart_spi *aus;
+ struct clk *clk;
+ int irq;
+ int ret;
+
+ regs = platform_get_resource(to_platform_device(pdev->dev.parent),
+ IORESOURCE_MEM, 0);
+ if (!regs)
+ return -EINVAL;
+
+ irq = platform_get_irq(to_platform_device(pdev->dev.parent), 0);
+ if (irq < 0)
+ return irq;
+
+ clk = devm_clk_get(pdev->dev.parent, "usart");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ ret = -ENOMEM;
+ controller = spi_alloc_master(&pdev->dev, sizeof(*aus));
+ if (!controller)
+ goto at91_usart_spi_probe_fail;
+
+ ret = at91_usart_gpio_setup(pdev);
+ if (ret)
+ goto at91_usart_spi_probe_fail;
+
+ controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LOOP | SPI_CS_HIGH;
+ controller->dev.of_node = pdev->dev.parent->of_node;
+ controller->bits_per_word_mask = SPI_BPW_MASK(8);
+ controller->setup = at91_usart_spi_setup;
+ controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
+ controller->transfer_one = at91_usart_spi_transfer_one;
+ controller->prepare_message = at91_usart_spi_prepare_message;
+ controller->unprepare_message = at91_usart_spi_unprepare_message;
+ controller->cleanup = at91_usart_spi_cleanup;
+ controller->max_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
+ US_MIN_CLK_DIV);
+ controller->min_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
+ US_MAX_CLK_DIV);
+ platform_set_drvdata(pdev, controller);
+
+ aus = spi_master_get_devdata(controller);
+
+ aus->dev = &pdev->dev;
+ aus->regs = devm_ioremap_resource(&pdev->dev, regs);
+ if (IS_ERR(aus->regs)) {
+ ret = PTR_ERR(aus->regs);
+ goto at91_usart_spi_probe_fail;
+ }
+
+ aus->irq = irq;
+ aus->clk = clk;
+
+ ret = devm_request_irq(&pdev->dev, irq, at91_usart_spi_interrupt, 0,
+ dev_name(&pdev->dev), controller);
+ if (ret)
+ goto at91_usart_spi_probe_fail;
+
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ goto at91_usart_spi_probe_fail;
+
+ aus->spi_clk = clk_get_rate(clk);
+ at91_usart_spi_init(aus);
+
+ spin_lock_init(&aus->lock);
+ ret = devm_spi_register_master(&pdev->dev, controller);
+ if (ret)
+ goto at91_usart_fail_register_master;
+
+ dev_info(&pdev->dev,
+ "AT91 USART SPI Controller version 0x%x at 0x%08x (irq %d)\n",
+ at91_usart_spi_readl(aus, VERSION),
+ regs->start, irq);
+
+ return 0;
+
+at91_usart_fail_register_master:
+ clk_disable_unprepare(clk);
+at91_usart_spi_probe_fail:
+ spi_master_put(controller);
+ return ret;
+}
+
+static int at91_usart_spi_remove(struct platform_device *pdev)
+{
+ struct spi_controller *ctlr = platform_get_drvdata(pdev);
+ struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+
+ clk_disable_unprepare(aus->clk);
+
+ return 0;
+}
+
+static const struct of_device_id at91_usart_spi_dt_ids[] = {
+ { .compatible = "microchip,at91sam9g45-usart-spi"},
+ { /* sentinel */}
+};
+
+MODULE_DEVICE_TABLE(of, at91_usart_spi_dt_ids);
+
+static struct platform_driver at91_usart_spi_driver = {
+ .driver = {
+ .name = "at91_usart_spi",
+ },
+ .probe = at91_usart_spi_probe,
+ .remove = at91_usart_spi_remove,
+};
+
+module_platform_driver(at91_usart_spi_driver);
+
+MODULE_DESCRIPTION("Microchip AT91 USART SPI Controller driver");
+MODULE_AUTHOR("Radu Pirea <radu.pirea@microchip.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:at91_usart_spi");
--
2.17.1
^ permalink raw reply related
* [PATCH v9 6/6] tty/serial: atmel: change the driver to work under at91-usart mfd
From: Radu Pirea @ 2018-06-25 10:21 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625102105.28383-1-radu.pirea@microchip.com>
This patch modifies the place where resources and device tree properties
are searched.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
---
drivers/tty/serial/Kconfig | 1 +
drivers/tty/serial/atmel_serial.c | 42 ++++++++++++++++++++-----------
2 files changed, 28 insertions(+), 15 deletions(-)
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index df8bd0c7b97d..32886c304641 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -118,6 +118,7 @@ config SERIAL_ATMEL
depends on ARCH_AT91 || COMPILE_TEST
select SERIAL_CORE
select SERIAL_MCTRL_GPIO if GPIOLIB
+ select MFD_AT91_USART
help
This enables the driver for the on-chip UARTs of the Atmel
AT91 processors.
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 8e4428725848..267d4d1de3f8 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -193,8 +193,7 @@ static struct console atmel_console;
#if defined(CONFIG_OF)
static const struct of_device_id atmel_serial_dt_ids[] = {
- { .compatible = "atmel,at91rm9200-usart" },
- { .compatible = "atmel,at91sam9260-usart" },
+ { .compatible = "atmel,at91rm9200-usart-serial" },
{ /* sentinel */ }
};
#endif
@@ -915,6 +914,7 @@ static void atmel_tx_dma(struct uart_port *port)
static int atmel_prepare_tx_dma(struct uart_port *port)
{
struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+ struct device *mfd_dev = port->dev->parent;
dma_cap_mask_t mask;
struct dma_slave_config config;
int ret, nent;
@@ -922,7 +922,7 @@ static int atmel_prepare_tx_dma(struct uart_port *port)
dma_cap_zero(mask);
dma_cap_set(DMA_SLAVE, mask);
- atmel_port->chan_tx = dma_request_slave_channel(port->dev, "tx");
+ atmel_port->chan_tx = dma_request_slave_channel(mfd_dev, "tx");
if (atmel_port->chan_tx == NULL)
goto chan_err;
dev_info(port->dev, "using %s for tx DMA transfers\n",
@@ -1093,6 +1093,7 @@ static void atmel_rx_from_dma(struct uart_port *port)
static int atmel_prepare_rx_dma(struct uart_port *port)
{
struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+ struct device *mfd_dev = port->dev->parent;
struct dma_async_tx_descriptor *desc;
dma_cap_mask_t mask;
struct dma_slave_config config;
@@ -1104,7 +1105,7 @@ static int atmel_prepare_rx_dma(struct uart_port *port)
dma_cap_zero(mask);
dma_cap_set(DMA_CYCLIC, mask);
- atmel_port->chan_rx = dma_request_slave_channel(port->dev, "rx");
+ atmel_port->chan_rx = dma_request_slave_channel(mfd_dev, "rx");
if (atmel_port->chan_rx == NULL)
goto chan_err;
dev_info(port->dev, "using %s for rx DMA transfers\n",
@@ -2222,8 +2223,8 @@ static const char *atmel_type(struct uart_port *port)
*/
static void atmel_release_port(struct uart_port *port)
{
- struct platform_device *pdev = to_platform_device(port->dev);
- int size = pdev->resource[0].end - pdev->resource[0].start + 1;
+ struct platform_device *mpdev = to_platform_device(port->dev->parent);
+ int size = resource_size(mpdev->resource);
release_mem_region(port->mapbase, size);
@@ -2238,8 +2239,8 @@ static void atmel_release_port(struct uart_port *port)
*/
static int atmel_request_port(struct uart_port *port)
{
- struct platform_device *pdev = to_platform_device(port->dev);
- int size = pdev->resource[0].end - pdev->resource[0].start + 1;
+ struct platform_device *mpdev = to_platform_device(port->dev->parent);
+ int size = resource_size(mpdev->resource);
if (!request_mem_region(port->mapbase, size, "atmel_serial"))
return -EBUSY;
@@ -2341,27 +2342,28 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
{
int ret;
struct uart_port *port = &atmel_port->uart;
+ struct platform_device *mpdev = to_platform_device(pdev->dev.parent);
atmel_init_property(atmel_port, pdev);
atmel_set_ops(port);
- uart_get_rs485_mode(&pdev->dev, &port->rs485);
+ uart_get_rs485_mode(&mpdev->dev, &port->rs485);
port->iotype = UPIO_MEM;
port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
port->ops = &atmel_pops;
port->fifosize = 1;
port->dev = &pdev->dev;
- port->mapbase = pdev->resource[0].start;
- port->irq = pdev->resource[1].start;
+ port->mapbase = mpdev->resource[0].start;
+ port->irq = mpdev->resource[1].start;
port->rs485_config = atmel_config_rs485;
- port->membase = NULL;
+ port->membase = NULL;
memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
/* for console, the clock could already be configured */
if (!atmel_port->clk) {
- atmel_port->clk = clk_get(&pdev->dev, "usart");
+ atmel_port->clk = clk_get(&mpdev->dev, "usart");
if (IS_ERR(atmel_port->clk)) {
ret = PTR_ERR(atmel_port->clk);
atmel_port->clk = NULL;
@@ -2694,13 +2696,22 @@ static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
static int atmel_serial_probe(struct platform_device *pdev)
{
struct atmel_uart_port *atmel_port;
- struct device_node *np = pdev->dev.of_node;
+ struct device_node *np = pdev->dev.parent->of_node;
void *data;
int ret = -ENODEV;
bool rs485_enabled;
BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
+ /*
+ * In device tree there is no node with "atmel,at91rm9200-usart-serial"
+ * as compatible string. This driver is probed by at91-usart mfd driver
+ * which is just a wrapper over the atmel_serial driver and
+ * spi-at91-usart driver. All attributes needed by this driver are
+ * found in of_node of parent.
+ */
+ pdev->dev.of_node = np;
+
ret = of_alias_get_id(np, "serial");
if (ret < 0)
/* port id not found in platform data nor device-tree aliases:
@@ -2836,6 +2847,7 @@ static int atmel_serial_remove(struct platform_device *pdev)
clk_put(atmel_port->clk);
atmel_port->clk = NULL;
+ pdev->dev.of_node = NULL;
return ret;
}
@@ -2846,7 +2858,7 @@ static struct platform_driver atmel_serial_driver = {
.suspend = atmel_serial_suspend,
.resume = atmel_serial_resume,
.driver = {
- .name = "atmel_usart",
+ .name = "atmel_usart_serial",
.of_match_table = of_match_ptr(atmel_serial_dt_ids),
},
};
--
2.17.1
^ permalink raw reply related
* Re: [PATCH v9 5/6] spi: at91-usart: add driver for at91-usart as spi
From: kbuild test robot @ 2018-06-25 15:06 UTC (permalink / raw)
Cc: kbuild-all, broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh, linux-spi,
linux-arm-kernel, linux-kernel, devicetree, linux-serial,
Radu Pirea
In-Reply-To: <20180625102105.28383-6-radu.pirea@microchip.com>
[-- Attachment #1: Type: text/plain, Size: 5044 bytes --]
Hi Radu,
I love your patch! Perhaps something to improve:
[auto build test WARNING on ljones-mfd/for-mfd-next]
[also build test WARNING on v4.18-rc2 next-20180625]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Radu-Pirea/Driver-for-at91-usart-in-spi-mode/20180625-183610
base: https://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git for-mfd-next
config: ia64-allmodconfig (attached as .config)
compiler: ia64-linux-gcc (GCC) 8.1.0
reproduce:
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
GCC_VERSION=8.1.0 make.cross ARCH=ia64
All warnings (new ones prefixed by >>):
In file included from include/linux/gpio/driver.h:5,
from include/asm-generic/gpio.h:13,
from include/linux/gpio.h:62,
from include/linux/of_gpio.h:16,
from drivers//spi/spi-at91-usart.c:14:
drivers//spi/spi-at91-usart.c: In function 'at91_usart_spi_probe':
>> drivers//spi/spi-at91-usart.c:389:4: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Wformat=]
"AT91 USART SPI Controller version 0x%x at 0x%08x (irq %d)\n",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers//spi/spi-at91-usart.c:391:4:
regs->start, irq);
~~~~~~~~~~~
include/linux/device.h:1382:51: note: in definition of macro 'dev_info'
#define dev_info(dev, fmt, arg...) _dev_info(dev, fmt, ##arg)
^~~
vim +389 drivers//spi/spi-at91-usart.c
312
313 static int at91_usart_spi_probe(struct platform_device *pdev)
314 {
315 struct resource *regs;
316 struct spi_controller *controller;
317 struct at91_usart_spi *aus;
318 struct clk *clk;
319 int irq;
320 int ret;
321
322 regs = platform_get_resource(to_platform_device(pdev->dev.parent),
323 IORESOURCE_MEM, 0);
324 if (!regs)
325 return -EINVAL;
326
327 irq = platform_get_irq(to_platform_device(pdev->dev.parent), 0);
328 if (irq < 0)
329 return irq;
330
331 clk = devm_clk_get(pdev->dev.parent, "usart");
332 if (IS_ERR(clk))
333 return PTR_ERR(clk);
334
335 ret = -ENOMEM;
336 controller = spi_alloc_master(&pdev->dev, sizeof(*aus));
337 if (!controller)
338 goto at91_usart_spi_probe_fail;
339
340 ret = at91_usart_gpio_setup(pdev);
341 if (ret)
342 goto at91_usart_spi_probe_fail;
343
344 controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LOOP | SPI_CS_HIGH;
345 controller->dev.of_node = pdev->dev.parent->of_node;
346 controller->bits_per_word_mask = SPI_BPW_MASK(8);
347 controller->setup = at91_usart_spi_setup;
348 controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
349 controller->transfer_one = at91_usart_spi_transfer_one;
350 controller->prepare_message = at91_usart_spi_prepare_message;
351 controller->unprepare_message = at91_usart_spi_unprepare_message;
352 controller->cleanup = at91_usart_spi_cleanup;
353 controller->max_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
354 US_MIN_CLK_DIV);
355 controller->min_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
356 US_MAX_CLK_DIV);
357 platform_set_drvdata(pdev, controller);
358
359 aus = spi_master_get_devdata(controller);
360
361 aus->dev = &pdev->dev;
362 aus->regs = devm_ioremap_resource(&pdev->dev, regs);
363 if (IS_ERR(aus->regs)) {
364 ret = PTR_ERR(aus->regs);
365 goto at91_usart_spi_probe_fail;
366 }
367
368 aus->irq = irq;
369 aus->clk = clk;
370
371 ret = devm_request_irq(&pdev->dev, irq, at91_usart_spi_interrupt, 0,
372 dev_name(&pdev->dev), controller);
373 if (ret)
374 goto at91_usart_spi_probe_fail;
375
376 ret = clk_prepare_enable(clk);
377 if (ret)
378 goto at91_usart_spi_probe_fail;
379
380 aus->spi_clk = clk_get_rate(clk);
381 at91_usart_spi_init(aus);
382
383 spin_lock_init(&aus->lock);
384 ret = devm_spi_register_master(&pdev->dev, controller);
385 if (ret)
386 goto at91_usart_fail_register_master;
387
388 dev_info(&pdev->dev,
> 389 "AT91 USART SPI Controller version 0x%x at 0x%08x (irq %d)\n",
390 at91_usart_spi_readl(aus, VERSION),
391 regs->start, irq);
392
393 return 0;
394
395 at91_usart_fail_register_master:
396 clk_disable_unprepare(clk);
397 at91_usart_spi_probe_fail:
398 spi_master_put(controller);
399 return ret;
400 }
401
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 49794 bytes --]
^ permalink raw reply
* [PATCH v10 0/6] Driver for at91 usart in spi mode
From: Radu Pirea @ 2018-06-25 17:22 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
Hello,
This is the second version of driver. I added a mfd driver which by
default probes atmel_serial driver and if in dt is specified to probe
the spi driver, then the spi-at91-usart driver will be probed. The
compatible for atmel_serial is now the compatible for at91-usart mfd
driver and compatilbe for atmel_serial driver was changed in order to
keep the bindings for serial as they are.
Changes in v10:
-fixed kbuild test robot warning
Changes in v9:
- minor changes
- rebased on top of broonie/for-4.19
Changes in v8:
- fixed passing an empty mfd cell if "atmel,usart-mode" value is invalid
Changes in v7:
- synced up SPDIX license with module license
- numbering of usart modes starts from 0 insteand of 1
Changes in v6:
- removed unused compatible strings from serial and spi drivers
Changes in v5:
- fixed usage of stdout-path property with atmel_serial driver
Changes in v4:
- modified the spi driver to use cs gpio support form spi subsystem
- fixed dma transfers for serial driver
- squashed binding for spi and serial and moved them to mfd/atmel-usart.txt
Changes in v3:
- fixed spi slaves probing
Changes in v2:
- added at91-usart mfd driver
- modified spi-at91-usart driver to work as mfd driver child
- modified atmel_serial driver to work as mfd driver child
Changes in v1:
- added spi-at91-usart driver
Radu Pirea (6):
MAINTAINERS: add at91 usart mfd driver
dt-bindings: add binding for atmel-usart in SPI mode
mfd: at91-usart: added mfd driver for usart
MAINTAINERS: add at91 usart spi driver
spi: at91-usart: add driver for at91-usart as spi
tty/serial: atmel: change the driver to work under at91-usart mfd
.../bindings/{serial => mfd}/atmel-usart.txt | 25 +-
MAINTAINERS | 16 +
drivers/mfd/Kconfig | 9 +
drivers/mfd/Makefile | 1 +
drivers/mfd/at91-usart.c | 71 +++
drivers/spi/Kconfig | 9 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-at91-usart.c | 432 ++++++++++++++++++
drivers/tty/serial/Kconfig | 1 +
drivers/tty/serial/atmel_serial.c | 42 +-
include/dt-bindings/mfd/at91-usart.h | 17 +
11 files changed, 607 insertions(+), 17 deletions(-)
rename Documentation/devicetree/bindings/{serial => mfd}/atmel-usart.txt (76%)
create mode 100644 drivers/mfd/at91-usart.c
create mode 100644 drivers/spi/spi-at91-usart.c
create mode 100644 include/dt-bindings/mfd/at91-usart.h
--
2.18.0
^ permalink raw reply
* [PATCH v10 1/6] MAINTAINERS: add at91 usart mfd driver
From: Radu Pirea @ 2018-06-25 17:22 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625172230.29686-1-radu.pirea@microchip.com>
Added entry for at91 usart mfd driver.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
---
MAINTAINERS | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 9d5eeff51b5f..7ac6e6af5292 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9321,6 +9321,7 @@ M: Richard Genoud <richard.genoud@gmail.com>
S: Maintained
F: drivers/tty/serial/atmel_serial.c
F: drivers/tty/serial/atmel_serial.h
+F: Documentation/devicetree/bindings/mfd/atmel-usart.txt
MICROCHIP / ATMEL DMA DRIVER
M: Ludovic Desroches <ludovic.desroches@microchip.com>
@@ -9353,6 +9354,14 @@ S: Supported
F: drivers/mtd/nand/raw/atmel/*
F: Documentation/devicetree/bindings/mtd/atmel-nand.txt
+MICROCHIP AT91 USART MFD DRIVER
+M: Radu Pirea <radu.pirea@microchip.com>
+L: linux-kernel@vger.kernel.org
+S: Supported
+F: drivers/mfd/at91-usart.c
+F: include/dt-bindings/mfd/at91-usart.h
+F: Documentation/devicetree/bindings/mfd/atmel-usart.txt
+
MICROCHIP KSZ SERIES ETHERNET SWITCH DRIVER
M: Woojung Huh <Woojung.Huh@microchip.com>
M: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
--
2.18.0
^ permalink raw reply related
* [PATCH v10 2/6] dt-bindings: add binding for atmel-usart in SPI mode
From: Radu Pirea @ 2018-06-25 17:22 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625172230.29686-1-radu.pirea@microchip.com>
This patch moves the bindings for serial from serial/atmel-usart.txt to
mfd/atmel-usart.txt and adds bindings for USART in SPI mode.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../bindings/{serial => mfd}/atmel-usart.txt | 25 +++++++++++++++++--
include/dt-bindings/mfd/at91-usart.h | 17 +++++++++++++
2 files changed, 40 insertions(+), 2 deletions(-)
rename Documentation/devicetree/bindings/{serial => mfd}/atmel-usart.txt (76%)
create mode 100644 include/dt-bindings/mfd/at91-usart.h
diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
similarity index 76%
rename from Documentation/devicetree/bindings/serial/atmel-usart.txt
rename to Documentation/devicetree/bindings/mfd/atmel-usart.txt
index 7c0d6b2f53e4..0348fef0f497 100644
--- a/Documentation/devicetree/bindings/serial/atmel-usart.txt
+++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt
@@ -1,6 +1,6 @@
* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART)
-Required properties:
+Required properties for USART:
- compatible: Should be "atmel,<chip>-usart" or "atmel,<chip>-dbgu"
The compatible <chip> indicated will be the first SoC to support an
additional mode or an USART new feature.
@@ -11,7 +11,13 @@ Required properties:
Required elements: "usart"
- clocks: phandles to input clocks.
-Optional properties:
+Required properties for USART in SPI mode:
+- #size-cells : Must be <0>
+- #address-cells : Must be <1>
+- cs-gpios: chipselects (internal cs not supported)
+- atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h)
+
+Optional properties in serial mode:
- atmel,use-dma-rx: use of PDC or DMA for receiving data
- atmel,use-dma-tx: use of PDC or DMA for transmitting data
- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively.
@@ -62,3 +68,18 @@ Example:
dma-names = "tx", "rx";
atmel,fifo-size = <32>;
};
+
+- SPI mode:
+ #include <dt-bindings/mfd/at91-usart.h>
+
+ spi0: spi@f001c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "atmel,at91rm9200-usart", "atmel,at91sam9260-usart";
+ atmel,usart-mode = <AT91_USART_MODE_SPI>;
+ reg = <0xf001c000 0x100>;
+ interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&usart0_clk>;
+ clock-names = "usart";
+ cs-gpios = <&pioB 3 0>;
+ };
diff --git a/include/dt-bindings/mfd/at91-usart.h b/include/dt-bindings/mfd/at91-usart.h
new file mode 100644
index 000000000000..2de5bc312e1e
--- /dev/null
+++ b/include/dt-bindings/mfd/at91-usart.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides macros for AT91 USART DT bindings.
+ *
+ * Copyright (C) 2018 Microchip Technology
+ *
+ * Author: Radu Pirea <radu.pirea@microchip.com>
+ *
+ */
+
+#ifndef __DT_BINDINGS_AT91_USART_H__
+#define __DT_BINDINGS_AT91_USART_H__
+
+#define AT91_USART_MODE_SERIAL 0
+#define AT91_USART_MODE_SPI 1
+
+#endif /* __DT_BINDINGS_AT91_USART_H__ */
--
2.18.0
^ permalink raw reply related
* [PATCH v10 3/6] mfd: at91-usart: added mfd driver for usart
From: Radu Pirea @ 2018-06-25 17:22 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625172230.29686-1-radu.pirea@microchip.com>
This mfd driver is just a wrapper over atmel_serial driver and
spi-at91-usart driver. Selection of one of the drivers is based on a
property from device tree. If the property is not specified, the default
driver is atmel_serial.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
---
drivers/mfd/Kconfig | 9 +++++
drivers/mfd/Makefile | 1 +
drivers/mfd/at91-usart.c | 71 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 81 insertions(+)
create mode 100644 drivers/mfd/at91-usart.c
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index b860eb5aa194..a886672b960d 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -99,6 +99,15 @@ config MFD_AAT2870_CORE
additional drivers must be enabled in order to use the
functionality of the device.
+config MFD_AT91_USART
+ tristate "AT91 USART Driver"
+ select MFD_CORE
+ help
+ Select this to get support for AT91 USART IP. This is a wrapper
+ over at91-usart-serial driver and usart-spi-driver. Only one function
+ can be used at a time. The choice is done at boot time by the probe
+ function of this MFD driver according to a device tree property.
+
config MFD_ATMEL_FLEXCOM
tristate "Atmel Flexcom (Flexible Serial Communication Unit)"
select MFD_CORE
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index e9fd20dba18d..c7e66928abb9 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -184,6 +184,7 @@ obj-$(CONFIG_MFD_SPMI_PMIC) += qcom-spmi-pmic.o
obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
obj-$(CONFIG_MFD_TPS65090) += tps65090.o
obj-$(CONFIG_MFD_AAT2870_CORE) += aat2870-core.o
+obj-$(CONFIG_MFD_AT91_USART) += at91-usart.o
obj-$(CONFIG_MFD_ATMEL_FLEXCOM) += atmel-flexcom.o
obj-$(CONFIG_MFD_ATMEL_HLCDC) += atmel-hlcdc.o
obj-$(CONFIG_MFD_ATMEL_SMC) += atmel-smc.o
diff --git a/drivers/mfd/at91-usart.c b/drivers/mfd/at91-usart.c
new file mode 100644
index 000000000000..a4b9929c156f
--- /dev/null
+++ b/drivers/mfd/at91-usart.c
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for AT91 USART
+ *
+ * Copyright (C) 2018 Microchip Technology
+ *
+ * Author: Radu Pirea <radu.pirea@microchip.com>
+ *
+ */
+
+#include <dt-bindings/mfd/at91-usart.h>
+
+#include <linux/module.h>
+#include <linux/mfd/core.h>
+#include <linux/property.h>
+
+static struct mfd_cell at91_usart_spi_subdev = {
+ .name = "at91_usart_spi",
+ .of_compatible = "microchip,at91sam9g45-usart-spi",
+ };
+
+static struct mfd_cell at91_usart_serial_subdev = {
+ .name = "atmel_usart_serial",
+ .of_compatible = "atmel,at91rm9200-usart-serial",
+ };
+
+static int at91_usart_mode_probe(struct platform_device *pdev)
+{
+ struct mfd_cell cell;
+ u32 opmode = AT91_USART_MODE_SERIAL;
+
+ device_property_read_u32(&pdev->dev, "atmel,usart-mode", &opmode);
+
+ switch (opmode) {
+ case AT91_USART_MODE_SPI:
+ cell = at91_usart_spi_subdev;
+ break;
+ case AT91_USART_MODE_SERIAL:
+ cell = at91_usart_serial_subdev;
+ break;
+ default:
+ dev_err(&pdev->dev, "atmel,usart-mode has an invalid value %u\n",
+ opmode);
+ return -EINVAL;
+ }
+
+ return devm_mfd_add_devices(&pdev->dev, PLATFORM_DEVID_AUTO, &cell, 1,
+ NULL, 0, NULL);
+}
+
+static const struct of_device_id at91_usart_mode_of_match[] = {
+ { .compatible = "atmel,at91rm9200-usart" },
+ { .compatible = "atmel,at91sam9260-usart" },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, at91_usart_mode_of_match);
+
+static struct platform_driver at91_usart_mfd = {
+ .probe = at91_usart_mode_probe,
+ .driver = {
+ .name = "at91_usart_mode",
+ .of_match_table = at91_usart_mode_of_match,
+ },
+};
+
+module_platform_driver(at91_usart_mfd);
+
+MODULE_AUTHOR("Radu Pirea <radu.pirea@microchip.com>");
+MODULE_DESCRIPTION("AT91 USART MFD driver");
+MODULE_LICENSE("GPL v2");
--
2.18.0
^ permalink raw reply related
* [PATCH v10 4/6] MAINTAINERS: add at91 usart spi driver
From: Radu Pirea @ 2018-06-25 17:22 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625172230.29686-1-radu.pirea@microchip.com>
Added entry for at91 usart mfd driver.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
---
MAINTAINERS | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 7ac6e6af5292..f849cc4acbf6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9362,6 +9362,13 @@ F: drivers/mfd/at91-usart.c
F: include/dt-bindings/mfd/at91-usart.h
F: Documentation/devicetree/bindings/mfd/atmel-usart.txt
+MICROCHIP AT91 USART SPI DRIVER
+M: Radu Pirea <radu.pirea@microchip.com>
+L: linux-spi@vger.kernel.org
+S: Supported
+F: drivers/spi/spi-at91-usart.c
+F: Documentation/devicetree/bindings/mfd/atmel-usart.txt
+
MICROCHIP KSZ SERIES ETHERNET SWITCH DRIVER
M: Woojung Huh <Woojung.Huh@microchip.com>
M: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
--
2.18.0
^ permalink raw reply related
* [PATCH v10 5/6] spi: at91-usart: add driver for at91-usart as spi
From: Radu Pirea @ 2018-06-25 17:22 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625172230.29686-1-radu.pirea@microchip.com>
This is the driver for at91-usart in spi mode. The USART IP can be configured
to work in many modes and one of them is SPI.
The driver was tested on sama5d3-xplained and sama5d4-xplained boards with
enc28j60 ethernet controller as slave.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
---
drivers/spi/Kconfig | 9 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-at91-usart.c | 432 +++++++++++++++++++++++++++++++++++
3 files changed, 442 insertions(+)
create mode 100644 drivers/spi/spi-at91-usart.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index ad5d68e1dab7..02bb35057ccd 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -83,6 +83,15 @@ config SPI_ATMEL
This selects a driver for the Atmel SPI Controller, present on
many AT91 ARM chips.
+config SPI_AT91_USART
+ tristate "Atmel USART Controller SPI driver"
+ depends on HAS_DMA
+ depends on (ARCH_AT91 || COMPILE_TEST)
+ select MFD_AT91_USART
+ help
+ This selects a driver for the AT91 USART Controller as SPI Master,
+ present on AT91 and SAMA5 SoC series.
+
config SPI_AU1550
tristate "Au1550/Au1200/Au1300 SPI Controller"
depends on MIPS_ALCHEMY
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index cb1f4378b87c..901ff606e6e5 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_SPI_LOOPBACK_TEST) += spi-loopback-test.o
obj-$(CONFIG_SPI_ALTERA) += spi-altera.o
obj-$(CONFIG_SPI_ARMADA_3700) += spi-armada-3700.o
obj-$(CONFIG_SPI_ATMEL) += spi-atmel.o
+obj-$(CONFIG_SPI_AT91_USART) += spi-at91-usart.o
obj-$(CONFIG_SPI_ATH79) += spi-ath79.o
obj-$(CONFIG_SPI_AU1550) += spi-au1550.o
obj-$(CONFIG_SPI_AXI_SPI_ENGINE) += spi-axi-spi-engine.o
diff --git a/drivers/spi/spi-at91-usart.c b/drivers/spi/spi-at91-usart.c
new file mode 100644
index 000000000000..5c6dd0d2c6a7
--- /dev/null
+++ b/drivers/spi/spi-at91-usart.c
@@ -0,0 +1,432 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for AT91 USART Controllers as SPI
+ *
+ * Copyright (C) 2018 Microchip Technology Inc.
+ * Author: Radu Pirea <radu.pirea@microchip.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+
+#include <linux/spi/spi.h>
+
+#define US_CR 0x00
+#define US_MR 0x04
+#define US_IER 0x08
+#define US_IDR 0x0C
+#define US_CSR 0x14
+#define US_RHR 0x18
+#define US_THR 0x1C
+#define US_BRGR 0x20
+#define US_VERSION 0xFC
+
+#define US_CR_RSTRX BIT(2)
+#define US_CR_RSTTX BIT(3)
+#define US_CR_RXEN BIT(4)
+#define US_CR_RXDIS BIT(5)
+#define US_CR_TXEN BIT(6)
+#define US_CR_TXDIS BIT(7)
+
+#define US_MR_SPI_MASTER 0x0E
+#define US_MR_CHRL GENMASK(7, 6)
+#define US_MR_CPHA BIT(8)
+#define US_MR_CPOL BIT(16)
+#define US_MR_CLKO BIT(18)
+#define US_MR_WRDBT BIT(20)
+#define US_MR_LOOP BIT(15)
+
+#define US_IR_RXRDY BIT(0)
+#define US_IR_TXRDY BIT(1)
+#define US_IR_OVRE BIT(5)
+
+#define US_BRGR_SIZE BIT(16)
+
+#define US_MIN_CLK_DIV 0x06
+#define US_MAX_CLK_DIV BIT(16)
+
+#define US_RESET (US_CR_RSTRX | US_CR_RSTTX)
+#define US_DISABLE (US_CR_RXDIS | US_CR_TXDIS)
+#define US_ENABLE (US_CR_RXEN | US_CR_TXEN)
+#define US_OVRE_RXRDY_IRQS (US_IR_OVRE | US_IR_RXRDY)
+
+#define US_INIT \
+ (US_MR_SPI_MASTER | US_MR_CHRL | US_MR_CLKO | US_MR_WRDBT)
+
+/* Register access macros */
+#define at91_usart_spi_readl(port, reg) \
+ readl_relaxed((port)->regs + US_##reg)
+#define at91_usart_spi_writel(port, reg, value) \
+ writel_relaxed((value), (port)->regs + US_##reg)
+
+#define at91_usart_spi_readb(port, reg) \
+ readb_relaxed((port)->regs + US_##reg)
+#define at91_usart_spi_writeb(port, reg, value) \
+ writeb_relaxed((value), (port)->regs + US_##reg)
+
+struct at91_usart_spi {
+ struct spi_transfer *current_transfer;
+ void __iomem *regs;
+ struct device *dev;
+ struct clk *clk;
+
+ /*used in interrupt to protect data reading*/
+ spinlock_t lock;
+
+ int irq;
+ unsigned int current_tx_remaining_bytes;
+ unsigned int current_rx_remaining_bytes;
+
+ u32 spi_clk;
+ u32 status;
+
+ bool xfer_failed;
+};
+
+static inline u32 at91_usart_spi_tx_ready(struct at91_usart_spi *aus)
+{
+ return aus->status & US_IR_TXRDY;
+}
+
+static inline u32 at91_usart_spi_rx_ready(struct at91_usart_spi *aus)
+{
+ return aus->status & US_IR_RXRDY;
+}
+
+static inline u32 at91_usart_spi_check_overrun(struct at91_usart_spi *aus)
+{
+ return aus->status & US_IR_OVRE;
+}
+
+static inline u32 at91_usart_spi_read_status(struct at91_usart_spi *aus)
+{
+ aus->status = at91_usart_spi_readl(aus, CSR);
+ return aus->status;
+}
+
+static inline void at91_usart_spi_tx(struct at91_usart_spi *aus)
+{
+ unsigned int len = aus->current_transfer->len;
+ unsigned int remaining = aus->current_tx_remaining_bytes;
+ const u8 *tx_buf = aus->current_transfer->tx_buf;
+
+ if (!remaining)
+ return;
+
+ if (at91_usart_spi_tx_ready(aus)) {
+ at91_usart_spi_writeb(aus, THR, tx_buf[len - remaining]);
+ aus->current_tx_remaining_bytes--;
+ }
+}
+
+static inline void at91_usart_spi_rx(struct at91_usart_spi *aus)
+{
+ int len = aus->current_transfer->len;
+ int remaining = aus->current_rx_remaining_bytes;
+ u8 *rx_buf = aus->current_transfer->rx_buf;
+
+ if (!remaining)
+ return;
+
+ rx_buf[len - remaining] = at91_usart_spi_readb(aus, RHR);
+ aus->current_rx_remaining_bytes--;
+}
+
+static inline void
+at91_usart_spi_set_xfer_speed(struct at91_usart_spi *aus,
+ struct spi_transfer *xfer)
+{
+ at91_usart_spi_writel(aus, BRGR,
+ DIV_ROUND_UP(aus->spi_clk, xfer->speed_hz));
+}
+
+static irqreturn_t at91_usart_spi_interrupt(int irq, void *dev_id)
+{
+ struct spi_controller *controller = dev_id;
+ struct at91_usart_spi *aus = spi_master_get_devdata(controller);
+
+ spin_lock(&aus->lock);
+ at91_usart_spi_read_status(aus);
+
+ if (at91_usart_spi_check_overrun(aus)) {
+ aus->xfer_failed = true;
+ at91_usart_spi_writel(aus, IDR, US_IR_OVRE | US_IR_RXRDY);
+ spin_unlock(&aus->lock);
+ return IRQ_HANDLED;
+ }
+
+ if (at91_usart_spi_rx_ready(aus)) {
+ at91_usart_spi_rx(aus);
+ spin_unlock(&aus->lock);
+ return IRQ_HANDLED;
+ }
+
+ spin_unlock(&aus->lock);
+
+ return IRQ_NONE;
+}
+
+static int at91_usart_spi_setup(struct spi_device *spi)
+{
+ struct at91_usart_spi *aus = spi_master_get_devdata(spi->controller);
+ u32 *ausd = spi->controller_state;
+ unsigned int mr = at91_usart_spi_readl(aus, MR);
+ u8 bits = spi->bits_per_word;
+
+ if (bits != 8) {
+ dev_dbg(&spi->dev, "Only 8 bits per word are supported\n");
+ return -EINVAL;
+ }
+
+ if (spi->mode & SPI_CPOL)
+ mr |= US_MR_CPOL;
+ else
+ mr &= ~US_MR_CPOL;
+
+ if (spi->mode & SPI_CPHA)
+ mr |= US_MR_CPHA;
+ else
+ mr &= ~US_MR_CPHA;
+
+ if (spi->mode & SPI_LOOP)
+ mr |= US_MR_LOOP;
+ else
+ mr &= ~US_MR_LOOP;
+
+ if (!ausd) {
+ ausd = kzalloc(sizeof(*ausd), GFP_KERNEL);
+ if (!ausd)
+ return -ENOMEM;
+
+ spi->controller_state = ausd;
+ }
+
+ *ausd = mr;
+
+ dev_dbg(&spi->dev,
+ "setup: bpw %u mode 0x%x -> mr %d %08x\n",
+ bits, spi->mode, spi->chip_select, mr);
+
+ return 0;
+}
+
+int at91_usart_spi_transfer_one(struct spi_controller *ctlr,
+ struct spi_device *spi,
+ struct spi_transfer *xfer)
+{
+ struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+
+ at91_usart_spi_set_xfer_speed(aus, xfer);
+ aus->xfer_failed = false;
+ aus->current_transfer = xfer;
+ aus->current_tx_remaining_bytes = xfer->len;
+ aus->current_rx_remaining_bytes = xfer->len;
+
+ while ((aus->current_tx_remaining_bytes ||
+ aus->current_rx_remaining_bytes) && !aus->xfer_failed) {
+ at91_usart_spi_read_status(aus);
+ at91_usart_spi_tx(aus);
+ cpu_relax();
+ }
+
+ if (aus->xfer_failed) {
+ dev_err(aus->dev, "Overrun!\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
+int at91_usart_spi_prepare_message(struct spi_controller *ctlr,
+ struct spi_message *message)
+{
+ struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+ struct spi_device *spi = message->spi;
+ u32 *ausd = spi->controller_state;
+
+ at91_usart_spi_writel(aus, CR, US_ENABLE);
+ at91_usart_spi_writel(aus, IER, US_OVRE_RXRDY_IRQS);
+ at91_usart_spi_writel(aus, MR, *ausd);
+
+ return 0;
+}
+
+int at91_usart_spi_unprepare_message(struct spi_controller *ctlr,
+ struct spi_message *message)
+{
+ struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+
+ at91_usart_spi_writel(aus, CR, US_RESET | US_DISABLE);
+ at91_usart_spi_writel(aus, IDR, US_OVRE_RXRDY_IRQS);
+
+ return 0;
+}
+
+static void at91_usart_spi_cleanup(struct spi_device *spi)
+{
+ struct at91_usart_spi_device *ausd = spi->controller_state;
+
+ spi->controller_state = NULL;
+ kfree(ausd);
+}
+
+static void at91_usart_spi_init(struct at91_usart_spi *aus)
+{
+ at91_usart_spi_writel(aus, MR, US_INIT);
+ at91_usart_spi_writel(aus, CR, US_RESET | US_DISABLE);
+}
+
+static int at91_usart_gpio_setup(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.parent->of_node;
+ int i;
+ int ret;
+ int nb;
+
+ if (!np)
+ return -EINVAL;
+
+ nb = of_gpio_named_count(np, "cs-gpios");
+ for (i = 0; i < nb; i++) {
+ int cs_gpio = of_get_named_gpio(np, "cs-gpios", i);
+
+ if (cs_gpio < 0)
+ return cs_gpio;
+
+ if (gpio_is_valid(cs_gpio)) {
+ ret = devm_gpio_request_one(&pdev->dev, cs_gpio,
+ GPIOF_DIR_OUT,
+ dev_name(&pdev->dev));
+ if (ret)
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int at91_usart_spi_probe(struct platform_device *pdev)
+{
+ struct resource *regs;
+ struct spi_controller *controller;
+ struct at91_usart_spi *aus;
+ struct clk *clk;
+ int irq;
+ int ret;
+
+ regs = platform_get_resource(to_platform_device(pdev->dev.parent),
+ IORESOURCE_MEM, 0);
+ if (!regs)
+ return -EINVAL;
+
+ irq = platform_get_irq(to_platform_device(pdev->dev.parent), 0);
+ if (irq < 0)
+ return irq;
+
+ clk = devm_clk_get(pdev->dev.parent, "usart");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ ret = -ENOMEM;
+ controller = spi_alloc_master(&pdev->dev, sizeof(*aus));
+ if (!controller)
+ goto at91_usart_spi_probe_fail;
+
+ ret = at91_usart_gpio_setup(pdev);
+ if (ret)
+ goto at91_usart_spi_probe_fail;
+
+ controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LOOP | SPI_CS_HIGH;
+ controller->dev.of_node = pdev->dev.parent->of_node;
+ controller->bits_per_word_mask = SPI_BPW_MASK(8);
+ controller->setup = at91_usart_spi_setup;
+ controller->flags = SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX;
+ controller->transfer_one = at91_usart_spi_transfer_one;
+ controller->prepare_message = at91_usart_spi_prepare_message;
+ controller->unprepare_message = at91_usart_spi_unprepare_message;
+ controller->cleanup = at91_usart_spi_cleanup;
+ controller->max_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
+ US_MIN_CLK_DIV);
+ controller->min_speed_hz = DIV_ROUND_UP(clk_get_rate(clk),
+ US_MAX_CLK_DIV);
+ platform_set_drvdata(pdev, controller);
+
+ aus = spi_master_get_devdata(controller);
+
+ aus->dev = &pdev->dev;
+ aus->regs = devm_ioremap_resource(&pdev->dev, regs);
+ if (IS_ERR(aus->regs)) {
+ ret = PTR_ERR(aus->regs);
+ goto at91_usart_spi_probe_fail;
+ }
+
+ aus->irq = irq;
+ aus->clk = clk;
+
+ ret = devm_request_irq(&pdev->dev, irq, at91_usart_spi_interrupt, 0,
+ dev_name(&pdev->dev), controller);
+ if (ret)
+ goto at91_usart_spi_probe_fail;
+
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ goto at91_usart_spi_probe_fail;
+
+ aus->spi_clk = clk_get_rate(clk);
+ at91_usart_spi_init(aus);
+
+ spin_lock_init(&aus->lock);
+ ret = devm_spi_register_master(&pdev->dev, controller);
+ if (ret)
+ goto at91_usart_fail_register_master;
+
+ dev_info(&pdev->dev,
+ "AT91 USART SPI Controller version 0x%x at %pa (irq %d)\n",
+ at91_usart_spi_readl(aus, VERSION),
+ ®s->start, irq);
+
+ return 0;
+
+at91_usart_fail_register_master:
+ clk_disable_unprepare(clk);
+at91_usart_spi_probe_fail:
+ spi_master_put(controller);
+ return ret;
+}
+
+static int at91_usart_spi_remove(struct platform_device *pdev)
+{
+ struct spi_controller *ctlr = platform_get_drvdata(pdev);
+ struct at91_usart_spi *aus = spi_master_get_devdata(ctlr);
+
+ clk_disable_unprepare(aus->clk);
+
+ return 0;
+}
+
+static const struct of_device_id at91_usart_spi_dt_ids[] = {
+ { .compatible = "microchip,at91sam9g45-usart-spi"},
+ { /* sentinel */}
+};
+
+MODULE_DEVICE_TABLE(of, at91_usart_spi_dt_ids);
+
+static struct platform_driver at91_usart_spi_driver = {
+ .driver = {
+ .name = "at91_usart_spi",
+ },
+ .probe = at91_usart_spi_probe,
+ .remove = at91_usart_spi_remove,
+};
+
+module_platform_driver(at91_usart_spi_driver);
+
+MODULE_DESCRIPTION("Microchip AT91 USART SPI Controller driver");
+MODULE_AUTHOR("Radu Pirea <radu.pirea@microchip.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:at91_usart_spi");
--
2.18.0
^ permalink raw reply related
* [PATCH v10 6/6] tty/serial: atmel: change the driver to work under at91-usart mfd
From: Radu Pirea @ 2018-06-25 17:22 UTC (permalink / raw)
To: broonie, nicolas.ferre, alexandre.belloni, lee.jones,
richard.genoud, robh+dt, mark.rutland, gregkh
Cc: linux-spi, linux-arm-kernel, linux-kernel, devicetree,
linux-serial, Radu Pirea
In-Reply-To: <20180625172230.29686-1-radu.pirea@microchip.com>
This patch modifies the place where resources and device tree properties
are searched.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
---
drivers/tty/serial/Kconfig | 1 +
drivers/tty/serial/atmel_serial.c | 42 ++++++++++++++++++++-----------
2 files changed, 28 insertions(+), 15 deletions(-)
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index df8bd0c7b97d..32886c304641 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -118,6 +118,7 @@ config SERIAL_ATMEL
depends on ARCH_AT91 || COMPILE_TEST
select SERIAL_CORE
select SERIAL_MCTRL_GPIO if GPIOLIB
+ select MFD_AT91_USART
help
This enables the driver for the on-chip UARTs of the Atmel
AT91 processors.
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 8e4428725848..267d4d1de3f8 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -193,8 +193,7 @@ static struct console atmel_console;
#if defined(CONFIG_OF)
static const struct of_device_id atmel_serial_dt_ids[] = {
- { .compatible = "atmel,at91rm9200-usart" },
- { .compatible = "atmel,at91sam9260-usart" },
+ { .compatible = "atmel,at91rm9200-usart-serial" },
{ /* sentinel */ }
};
#endif
@@ -915,6 +914,7 @@ static void atmel_tx_dma(struct uart_port *port)
static int atmel_prepare_tx_dma(struct uart_port *port)
{
struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+ struct device *mfd_dev = port->dev->parent;
dma_cap_mask_t mask;
struct dma_slave_config config;
int ret, nent;
@@ -922,7 +922,7 @@ static int atmel_prepare_tx_dma(struct uart_port *port)
dma_cap_zero(mask);
dma_cap_set(DMA_SLAVE, mask);
- atmel_port->chan_tx = dma_request_slave_channel(port->dev, "tx");
+ atmel_port->chan_tx = dma_request_slave_channel(mfd_dev, "tx");
if (atmel_port->chan_tx == NULL)
goto chan_err;
dev_info(port->dev, "using %s for tx DMA transfers\n",
@@ -1093,6 +1093,7 @@ static void atmel_rx_from_dma(struct uart_port *port)
static int atmel_prepare_rx_dma(struct uart_port *port)
{
struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
+ struct device *mfd_dev = port->dev->parent;
struct dma_async_tx_descriptor *desc;
dma_cap_mask_t mask;
struct dma_slave_config config;
@@ -1104,7 +1105,7 @@ static int atmel_prepare_rx_dma(struct uart_port *port)
dma_cap_zero(mask);
dma_cap_set(DMA_CYCLIC, mask);
- atmel_port->chan_rx = dma_request_slave_channel(port->dev, "rx");
+ atmel_port->chan_rx = dma_request_slave_channel(mfd_dev, "rx");
if (atmel_port->chan_rx == NULL)
goto chan_err;
dev_info(port->dev, "using %s for rx DMA transfers\n",
@@ -2222,8 +2223,8 @@ static const char *atmel_type(struct uart_port *port)
*/
static void atmel_release_port(struct uart_port *port)
{
- struct platform_device *pdev = to_platform_device(port->dev);
- int size = pdev->resource[0].end - pdev->resource[0].start + 1;
+ struct platform_device *mpdev = to_platform_device(port->dev->parent);
+ int size = resource_size(mpdev->resource);
release_mem_region(port->mapbase, size);
@@ -2238,8 +2239,8 @@ static void atmel_release_port(struct uart_port *port)
*/
static int atmel_request_port(struct uart_port *port)
{
- struct platform_device *pdev = to_platform_device(port->dev);
- int size = pdev->resource[0].end - pdev->resource[0].start + 1;
+ struct platform_device *mpdev = to_platform_device(port->dev->parent);
+ int size = resource_size(mpdev->resource);
if (!request_mem_region(port->mapbase, size, "atmel_serial"))
return -EBUSY;
@@ -2341,27 +2342,28 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
{
int ret;
struct uart_port *port = &atmel_port->uart;
+ struct platform_device *mpdev = to_platform_device(pdev->dev.parent);
atmel_init_property(atmel_port, pdev);
atmel_set_ops(port);
- uart_get_rs485_mode(&pdev->dev, &port->rs485);
+ uart_get_rs485_mode(&mpdev->dev, &port->rs485);
port->iotype = UPIO_MEM;
port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
port->ops = &atmel_pops;
port->fifosize = 1;
port->dev = &pdev->dev;
- port->mapbase = pdev->resource[0].start;
- port->irq = pdev->resource[1].start;
+ port->mapbase = mpdev->resource[0].start;
+ port->irq = mpdev->resource[1].start;
port->rs485_config = atmel_config_rs485;
- port->membase = NULL;
+ port->membase = NULL;
memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
/* for console, the clock could already be configured */
if (!atmel_port->clk) {
- atmel_port->clk = clk_get(&pdev->dev, "usart");
+ atmel_port->clk = clk_get(&mpdev->dev, "usart");
if (IS_ERR(atmel_port->clk)) {
ret = PTR_ERR(atmel_port->clk);
atmel_port->clk = NULL;
@@ -2694,13 +2696,22 @@ static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
static int atmel_serial_probe(struct platform_device *pdev)
{
struct atmel_uart_port *atmel_port;
- struct device_node *np = pdev->dev.of_node;
+ struct device_node *np = pdev->dev.parent->of_node;
void *data;
int ret = -ENODEV;
bool rs485_enabled;
BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
+ /*
+ * In device tree there is no node with "atmel,at91rm9200-usart-serial"
+ * as compatible string. This driver is probed by at91-usart mfd driver
+ * which is just a wrapper over the atmel_serial driver and
+ * spi-at91-usart driver. All attributes needed by this driver are
+ * found in of_node of parent.
+ */
+ pdev->dev.of_node = np;
+
ret = of_alias_get_id(np, "serial");
if (ret < 0)
/* port id not found in platform data nor device-tree aliases:
@@ -2836,6 +2847,7 @@ static int atmel_serial_remove(struct platform_device *pdev)
clk_put(atmel_port->clk);
atmel_port->clk = NULL;
+ pdev->dev.of_node = NULL;
return ret;
}
@@ -2846,7 +2858,7 @@ static struct platform_driver atmel_serial_driver = {
.suspend = atmel_serial_suspend,
.resume = atmel_serial_resume,
.driver = {
- .name = "atmel_usart",
+ .name = "atmel_usart_serial",
.of_match_table = of_match_ptr(atmel_serial_dt_ids),
},
};
--
2.18.0
^ permalink raw reply related
* Re: [PATCH v2 1/8] dt-bindings: tegra186-hsp: Add shared interrupts
From: Rob Herring @ 2018-06-25 19:07 UTC (permalink / raw)
To: Mikko Perttunen
Cc: mark.rutland, jassisinghbrar, gregkh, thierry.reding, jonathanh,
devicetree, linux-serial, linux-tegra, linux-arm-kernel,
linux-kernel
In-Reply-To: <20180620122042.10950-2-mperttunen@nvidia.com>
On Wed, Jun 20, 2018 at 03:20:35PM +0300, Mikko Perttunen wrote:
> HSP interrupts can be routed through exposed "shared interrupts". These
> interrupts can be mapped to various internal interrupt lines. Add
> interrupt properties for shared interrupts to the tegra186-hsp device
> tree bindings. At the same time, add the compatibility string for
> tegra194-hsp, which is backwards compatible with tegra186.
>
> Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
> ---
>
> Notes:
> v2:
> - Edited commit message to not say that doorbell interrupts cannot be
> routed to shared interrupts.
> - Added tegra194 compatibility string.
>
> Documentation/devicetree/bindings/mailbox/nvidia,tegra186-hsp.txt | 3 +++
> 1 file changed, 3 insertions(+)
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply
* [PATCH 0/2] Add basic SoC support for MT6765
From: Mars Cheng @ 2018-06-26 2:04 UTC (permalink / raw)
To: Matthias Brugger, Rob Herring, Marc Zyngier
Cc: CC Hwang, Loda Chou, Miles Chen, Jades Shih, Yingjoe Chen,
My Chuang, linux-kernel, linux-mediatek, devicetree, wsd_upstream,
linux-serial, linux-arm-kernel
This patch adds basic SoC support for Mediatek's new 8-core SoC,
MT6765, which is mainly for smartphone application.
Change in V2:
1. fix clk properties in uart dts node
2. fix typo in submit title
3. add simple-bus in mt6765.dtsi
4. use correct SPDX license format
Mars Cheng (2):
dt-bindings: mediatek: Add bindings for mediatek MT6765 Platform
arm64: dts: mediatek: add mt6765 support
Documentation/devicetree/bindings/arm/mediatek.txt | 4 +
.../interrupt-controller/mediatek,sysirq.txt | 1 +
.../devicetree/bindings/serial/mtk-uart.txt | 1 +
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt6765-evb.dts | 33 ++++
arch/arm64/boot/dts/mediatek/mt6765.dtsi | 158 ++++++++++++++++++++
6 files changed, 198 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt6765-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt6765.dtsi
^ permalink raw reply
* [PATCH v2 1/2] dt-bindings: mediatek: Add bindings for mediatek MT6765 Platform
From: Mars Cheng @ 2018-06-26 2:04 UTC (permalink / raw)
To: Matthias Brugger, Rob Herring, Marc Zyngier
Cc: CC Hwang, Loda Chou, Miles Chen, Jades Shih, Yingjoe Chen,
My Chuang, linux-kernel, linux-mediatek, devicetree, wsd_upstream,
linux-serial, linux-arm-kernel, Mars Cheng
In-Reply-To: <1529978646-28976-1-git-send-email-mars.cheng@mediatek.com>
This adds dt-binding documentation for Mediatek MT6765. Only
include very basic items, gic, uart timer and cpu.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
---
Documentation/devicetree/bindings/arm/mediatek.txt | 4 ++++
.../interrupt-controller/mediatek,sysirq.txt | 1 +
.../devicetree/bindings/serial/mtk-uart.txt | 1 +
3 files changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt
index 7d21ab3..48fac4e 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek.txt
@@ -11,6 +11,7 @@ compatible: Must contain one of
"mediatek,mt6589"
"mediatek,mt6592"
"mediatek,mt6755"
+ "mediatek,mt6765"
"mediatek,mt6795"
"mediatek,mt6797"
"mediatek,mt7622"
@@ -41,6 +42,9 @@ Supported boards:
- Evaluation phone for MT6755(Helio P10):
Required root node properties:
- compatible = "mediatek,mt6755-evb", "mediatek,mt6755";
+- Evaluation board for MT6765(Helio P22):
+ Required root node properties:
+ - compatible = "mediatek,mt6765-evb", "mediatek,mt6765";
- Evaluation board for MT6795(Helio X10):
Required root node properties:
- compatible = "mediatek,mt6795-evb", "mediatek,mt6795";
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
index 07bf0b9..c8eda80 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@@ -11,6 +11,7 @@ Required properties:
"mediatek,mt7622-sysirq", "mediatek,mt6577-sysirq": for MT7622
"mediatek,mt6795-sysirq", "mediatek,mt6577-sysirq": for MT6795
"mediatek,mt6797-sysirq", "mediatek,mt6577-sysirq": for MT6797
+ "mediatek,mt6765-sysirq", "mediatek,mt6577-sysirq": for MT6765
"mediatek,mt6755-sysirq", "mediatek,mt6577-sysirq": for MT6755
"mediatek,mt6592-sysirq", "mediatek,mt6577-sysirq": for MT6592
"mediatek,mt6589-sysirq", "mediatek,mt6577-sysirq": for MT6589
diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt
index f73abff..742cb47 100644
--- a/Documentation/devicetree/bindings/serial/mtk-uart.txt
+++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt
@@ -8,6 +8,7 @@ Required properties:
* "mediatek,mt6582-uart" for MT6582 compatible UARTS
* "mediatek,mt6589-uart" for MT6589 compatible UARTS
* "mediatek,mt6755-uart" for MT6755 compatible UARTS
+ * "mediatek,mt6765-uart" for MT6765 compatible UARTS
* "mediatek,mt6795-uart" for MT6795 compatible UARTS
* "mediatek,mt6797-uart" for MT6797 compatible UARTS
* "mediatek,mt7622-uart" for MT7622 compatible UARTS
--
1.7.9.5
^ permalink raw reply related
* [PATCH v2 2/2] arm64: dts: mediatek: add mt6765 support
From: Mars Cheng @ 2018-06-26 2:04 UTC (permalink / raw)
To: Matthias Brugger, Rob Herring, Marc Zyngier
Cc: CC Hwang, Loda Chou, Miles Chen, Jades Shih, Yingjoe Chen,
My Chuang, linux-kernel, linux-mediatek, devicetree, wsd_upstream,
linux-serial, linux-arm-kernel, Mars Cheng
In-Reply-To: <1529978646-28976-1-git-send-email-mars.cheng@mediatek.com>
This adds basic chip support for MT6765 SoC.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
arch/arm64/boot/dts/mediatek/mt6765-evb.dts | 33 ++++++
arch/arm64/boot/dts/mediatek/mt6765.dtsi | 158 +++++++++++++++++++++++++++
3 files changed, 192 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt6765-evb.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt6765.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index ac17f60..7506b0d 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_MEDIATEK) += mt2712-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt6765-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt6765-evb.dts b/arch/arm64/boot/dts/mediatek/mt6765-evb.dts
new file mode 100644
index 0000000..36dddff2
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt6765-evb.dts
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Mediatek MT6765
+ *
+ * (C) Copyright 2018. Mediatek, Inc.
+ *
+ * Mars Cheng <mars.cheng@mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt6765.dtsi"
+
+/ {
+ model = "MediaTek MT6765 EVB";
+ compatible = "mediatek,mt6765-evb", "mediatek,mt6765";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0 0x1e800000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt6765.dtsi b/arch/arm64/boot/dts/mediatek/mt6765.dtsi
new file mode 100644
index 0000000..ab34c0f
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt6765.dtsi
@@ -0,0 +1,158 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Mediatek MT6765
+ *
+ * (C) Copyright 2018. Mediatek, Inc.
+ *
+ * Mars Cheng <mars.cheng@mediatek.com>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "mediatek,mt6765";
+ interrupt-parent = <&sysirq>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x000>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x001>;
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x002>;
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x003>;
+ };
+
+ cpu4: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x100>;
+ };
+
+ cpu5: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x101>;
+ };
+
+ cpu6: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x102>;
+ };
+
+ cpu7: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ enable-method = "psci";
+ reg = <0x103>;
+ };
+ };
+
+ baud_clk: dummy26m {
+ compatible = "fixed-clock";
+ clock-frequency = <26000000>;
+ #clock-cells = <0>;
+ };
+
+ sys_clk: dummyclk {
+ compatible = "fixed-clock";
+ clock-frequency = <26000000>;
+ #clock-cells = <0>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ ranges;
+
+ sysirq: intpol-controller@10200a80 {
+ compatible = "mediatek,mt6765-sysirq",
+ "mediatek,mt6577-sysirq";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupt-parent = <&gic>;
+ reg = <0 0x10200a80 0 0x50>;
+ };
+
+ gic: interrupt-controller@0c000000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ #redistributor-regions = <1>;
+ interrupt-parent = <&gic>;
+ interrupt-controller;
+ reg = <0 0x0c000000 0 0x40000>, // distributor
+ <0 0x0c100000 0 0x200000>; // redistributor
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ uart0: serial@11002000 {
+ compatible = "mediatek,mt6765-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11002000 0 0x400>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&baud_clk>, <&sys_clk>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt6765-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&baud_clk>, <&sys_clk>;
+ clock-names = "baud", "bus";
+ status = "disabled";
+ };
+ }; /* end of soc */
+};
--
1.7.9.5
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox