* [PATCH 02/02] ARM: shmobile: r8a7793: gose: HDMI prototype hack
@ 2015-11-16 9:15 Magnus Damm
2015-11-24 23:47 ` Laurent Pinchart
0 siblings, 1 reply; 2+ messages in thread
From: Magnus Damm @ 2015-11-16 9:15 UTC (permalink / raw)
To: linux-sh
From: Magnus Damm <damm+renesas@opensource.se>
This prototype patch adds r8a7793 GOSE HDMI video out support.
The r8a7793 GOSE board is similar to r8a7791 Koelsch. For those
boards an on-board HDMI encoder chip drives an HDMI port and
also a LVDS port is available for external LCD panels.
Basic testing with modetest seems to work well, but due to the
current state of r8a7793 SoC support all the dependencies are
not yet in place. In particular I2C and GPIO are lacking.
To check if the DU and HDMI drivers and hardware are working this
patch simply ties together I2C2 and GPIO3 with the DU and HDMI
devices. Once I2C and GPIO is enabled in upstream for r8a7793 and
GOSE then this patch can easily be reworked into something more
suitable for upstream.
Not-yet-Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
---
arch/arm/boot/dts/r8a7793-gose.dts | 98 ++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/r8a7793.dtsi | 33 +++++++++++-
2 files changed, 128 insertions(+), 3 deletions(-)
--- 0001/arch/arm/boot/dts/r8a7793-gose.dts
+++ work/arch/arm/boot/dts/r8a7793-gose.dts 2015-11-16 15:31:42.150513000 +0900
@@ -31,6 +31,54 @@
device_type = "memory";
reg = <0 0x40000000 0 0x40000000>;
};
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&adv7511_out>;
+ };
+ };
+ };
+
+ x2_clk: x2-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <74250000>;
+ };
+
+ x13_clk: x13-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <148500000>;
+ };
+};
+
+&du {
+ pinctrl-0 = <&du_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ clocks = <&mstp7_clks R8A7793_CLK_DU0>,
+ <&mstp7_clks R8A7793_CLK_DU1>,
+ <&mstp7_clks R8A7793_CLK_LVDS0>,
+ <&x13_clk>, <&x2_clk>;
+ clock-names = "du.0", "du.1", "lvds.0",
+ "dclkin.0", "dclkin.1";
+
+ ports {
+ port@0 {
+ endpoint {
+ remote-endpoint = <&adv7511_in>;
+ };
+ };
+ port@1 {
+ lvds_connector: endpoint {
+ };
+ };
+ };
};
&extal_clk {
@@ -38,6 +86,16 @@
};
&pfc {
+ i2c2_pins: i2c2 {
+ renesas,groups = "i2c2";
+ renesas,function = "i2c2";
+ };
+
+ du_pins: du {
+ renesas,groups = "du_rgb666", "du_sync", "du_disp", "du_clk_out_0";
+ renesas,function = "du";
+ };
+
scif0_pins: serial0 {
renesas,groups = "scif0_data_d";
renesas,function = "scif0";
@@ -134,4 +192,44 @@
};
};
};
+};
+
+&i2c2 {
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+ clock-frequency = <100000>;
+
+ hdmi@39 {
+ compatible = "adi,adv7511w";
+ reg = <0x39>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7511_in: endpoint {
+ remote-endpoint = <&du_out_rgb>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7511_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
};
--- 0013/arch/arm/boot/dts/r8a7793.dtsi
+++ work/arch/arm/boot/dts/r8a7793.dtsi 2015-11-16 15:34:33.710513000 +0900
@@ -19,6 +19,7 @@
#size-cells = <2>;
aliases {
+ i2c2 = &i2c2;
spi0 = &qspi;
};
@@ -57,6 +58,19 @@
interrupts = <1 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
};
+ gpio3: gpio@e6053000 {
+ compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar";
+ reg = <0 0xe6053000 0 0x50>;
+ interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-ranges = <&pfc 0 96 32>;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ clocks = <&mstp9_clks R8A7793_CLK_GPIO3>;
+ power-domains = <&cpg_clocks>;
+ };
+
thermal@e61f0000 {
compatible = "renesas,thermal-r8a7793", "renesas,rcar-thermal";
reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
@@ -194,6 +208,17 @@
dma-channels = <15>;
};
+ i2c2: i2c@e6530000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7793";
+ reg = <0 0xe6530000 0 0x40>;
+ interrupts = <0 286 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp9_clks R8A7793_CLK_I2C2>;
+ power-domains = <&cpg_clocks>;
+ status = "disabled";
+ };
+
scif0: serial@e6e60000 {
compatible = "renesas,scif-r8a7793", "renesas,scif";
reg = <0 0xe6e60000 0 64>;
@@ -514,10 +539,12 @@
mstp9_clks: mstp9_clks@e6150994 {
compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-clocks";
reg = <0 0xe6150994 0 4>, <0 0xe61509a4 0 4>;
- clocks = <&cpg_clocks R8A7793_CLK_QSPI>;
+ clocks = <&cp_clk>, <&cpg_clocks R8A7793_CLK_QSPI>,
+ <&hp_clk>;
#clock-cells = <1>;
- clock-indices = <R8A7793_CLK_QSPI_MOD>;
- clock-output-names = "qspi_mod";
+ clock-indices = <R8A7793_CLK_GPIO3 R8A7793_CLK_QSPI_MOD
+ R8A7793_CLK_I2C2>;
+ clock-output-names = "gpio3", "qspi_mod", "i2c2";
};
};
^ permalink raw reply [flat|nested] 2+ messages in thread* Re: [PATCH 02/02] ARM: shmobile: r8a7793: gose: HDMI prototype hack
2015-11-16 9:15 [PATCH 02/02] ARM: shmobile: r8a7793: gose: HDMI prototype hack Magnus Damm
@ 2015-11-24 23:47 ` Laurent Pinchart
0 siblings, 0 replies; 2+ messages in thread
From: Laurent Pinchart @ 2015-11-24 23:47 UTC (permalink / raw)
To: linux-sh
Hi Magnus,
Thank you for the patch.
On Monday 16 November 2015 18:15:32 Magnus Damm wrote:
> From: Magnus Damm <damm+renesas@opensource.se>
>
> This prototype patch adds r8a7793 GOSE HDMI video out support.
>
> The r8a7793 GOSE board is similar to r8a7791 Koelsch. For those
> boards an on-board HDMI encoder chip drives an HDMI port and
> also a LVDS port is available for external LCD panels.
>
> Basic testing with modetest seems to work well, but due to the
> current state of r8a7793 SoC support all the dependencies are
> not yet in place. In particular I2C and GPIO are lacking.
>
> To check if the DU and HDMI drivers and hardware are working this
> patch simply ties together I2C2 and GPIO3 with the DU and HDMI
> devices. Once I2C and GPIO is enabled in upstream for r8a7793 and
> GOSE then this patch can easily be reworked into something more
> suitable for upstream.
>
> Not-yet-Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
> ---
>
> arch/arm/boot/dts/r8a7793-gose.dts | 98 +++++++++++++++++++++++++++++++++
> arch/arm/boot/dts/r8a7793.dtsi | 33 +++++++++++-
> 2 files changed, 128 insertions(+), 3 deletions(-)
>
> --- 0001/arch/arm/boot/dts/r8a7793-gose.dts
> +++ work/arch/arm/boot/dts/r8a7793-gose.dts 2015-11-16 15:31:42.150513000
> +0900 @@ -31,6 +31,54 @@
> device_type = "memory";
> reg = <0 0x40000000 0 0x40000000>;
> };
> +
> + hdmi-out {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con: endpoint {
> + remote-endpoint = <&adv7511_out>;
> + };
> + };
> + };
> +
> + x2_clk: x2-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <74250000>;
> + };
> +
> + x13_clk: x13-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <148500000>;
> + };
> +};
> +
> +&du {
> + pinctrl-0 = <&du_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + clocks = <&mstp7_clks R8A7793_CLK_DU0>,
> + <&mstp7_clks R8A7793_CLK_DU1>,
> + <&mstp7_clks R8A7793_CLK_LVDS0>,
> + <&x13_clk>, <&x2_clk>;
> + clock-names = "du.0", "du.1", "lvds.0",
> + "dclkin.0", "dclkin.1";
> +
> + ports {
> + port@0 {
> + endpoint {
> + remote-endpoint = <&adv7511_in>;
> + };
> + };
> + port@1 {
> + lvds_connector: endpoint {
> + };
> + };
> + };
> };
>
> &extal_clk {
> @@ -38,6 +86,16 @@
> };
>
> &pfc {
> + i2c2_pins: i2c2 {
> + renesas,groups = "i2c2";
> + renesas,function = "i2c2";
> + };
> +
> + du_pins: du {
> + renesas,groups = "du_rgb666", "du_sync", "du_disp", "du_clk_out_0";
Blatant copy & paste of a Koelsch bug :-) You should use du_rgb888 here as the
DU RGB output has all 24 data bits connected to the HDMI transmitter. I'll
send a fix for Koelsch that itself copied the pin group from Lager for which
only 18 data pins are connected.
Apart from that the DU section looks good. Feel free to add my
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
when you'll resend the DU portion with the above problem fixed.
> + renesas,function = "du";
> + };
> +
> scif0_pins: serial0 {
> renesas,groups = "scif0_data_d";
> renesas,function = "scif0";
> @@ -134,4 +192,44 @@
> };
> };
> };
> +};
> +
> +&i2c2 {
> + pinctrl-0 = <&i2c2_pins>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> + clock-frequency = <100000>;
> +
> + hdmi@39 {
> + compatible = "adi,adv7511w";
> + reg = <0x39>;
> + interrupt-parent = <&gpio3>;
> + interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
> +
> + adi,input-depth = <8>;
> + adi,input-colorspace = "rgb";
> + adi,input-clock = "1x";
> + adi,input-style = <1>;
> + adi,input-justification = "evenly";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + adv7511_in: endpoint {
> + remote-endpoint = <&du_out_rgb>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + adv7511_out: endpoint {
> + remote-endpoint = <&hdmi_con>;
> + };
> + };
> + };
> + };
> };
> --- 0013/arch/arm/boot/dts/r8a7793.dtsi
> +++ work/arch/arm/boot/dts/r8a7793.dtsi 2015-11-16 15:34:33.710513000 +0900
> @@ -19,6 +19,7 @@
> #size-cells = <2>;
>
> aliases {
> + i2c2 = &i2c2;
> spi0 = &qspi;
> };
>
> @@ -57,6 +58,19 @@
> interrupts = <1 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
> };
>
> + gpio3: gpio@e6053000 {
> + compatible = "renesas,gpio-r8a7793", "renesas,gpio-rcar";
> + reg = <0 0xe6053000 0 0x50>;
> + interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
> + #gpio-cells = <2>;
> + gpio-controller;
> + gpio-ranges = <&pfc 0 96 32>;
> + #interrupt-cells = <2>;
> + interrupt-controller;
> + clocks = <&mstp9_clks R8A7793_CLK_GPIO3>;
> + power-domains = <&cpg_clocks>;
> + };
> +
> thermal@e61f0000 {
> compatible = "renesas,thermal-r8a7793", "renesas,rcar-thermal";
> reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>;
> @@ -194,6 +208,17 @@
> dma-channels = <15>;
> };
>
> + i2c2: i2c@e6530000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "renesas,i2c-r8a7793";
> + reg = <0 0xe6530000 0 0x40>;
> + interrupts = <0 286 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&mstp9_clks R8A7793_CLK_I2C2>;
> + power-domains = <&cpg_clocks>;
> + status = "disabled";
> + };
> +
> scif0: serial@e6e60000 {
> compatible = "renesas,scif-r8a7793", "renesas,scif";
> reg = <0 0xe6e60000 0 64>;
> @@ -514,10 +539,12 @@
> mstp9_clks: mstp9_clks@e6150994 {
> compatible = "renesas,r8a7793-mstp-clocks", "renesas,cpg-mstp-
clocks";
> reg = <0 0xe6150994 0 4>, <0 0xe61509a4 0 4>;
> - clocks = <&cpg_clocks R8A7793_CLK_QSPI>;
> + clocks = <&cp_clk>, <&cpg_clocks R8A7793_CLK_QSPI>,
> + <&hp_clk>;
> #clock-cells = <1>;
> - clock-indices = <R8A7793_CLK_QSPI_MOD>;
> - clock-output-names = "qspi_mod";
> + clock-indices = <R8A7793_CLK_GPIO3 R8A7793_CLK_QSPI_MOD
> + R8A7793_CLK_I2C2>;
> + clock-output-names = "gpio3", "qspi_mod", "i2c2";
> };
> };
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2015-11-24 23:47 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-11-16 9:15 [PATCH 02/02] ARM: shmobile: r8a7793: gose: HDMI prototype hack Magnus Damm
2015-11-24 23:47 ` Laurent Pinchart
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox