* WARNING: unexpected IO-APIC, please mail ....
@ 2002-12-17 14:19 Sebastian Frei
0 siblings, 0 replies; 2+ messages in thread
From: Sebastian Frei @ 2002-12-17 14:19 UTC (permalink / raw)
To: linux-smp
Mainboard: MSI KT4V-L
256MB DDR333
BIOS Ver. 1.6
Linux version 2.5.52 (root@NOP) (gcc version 3.2) #1 Mon Dez 16 21:00:50 CET
2002
Video mode to be used for restore is fffd
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
255MB LOWMEM available.
found SMP MP-table at 000fb930
hm, page 000fb000 reserved twice.
hm, page 000fc000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f7000 reserved twice.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
ACPI: RSDP (v000 AMI ) @ 0x000fa980
ACPI: RSDT (v001 AMIINT VIA_K7 00000.00016) @ 0x0fff0000
ACPI: FADT (v001 AMIINT VIA_K7 00000.00017) @ 0x0fff0030
ACPI: MADT (v001 AMIINT VIA_K7 00000.00009) @ 0x0fff00c0
ACPI: DSDT (v001 VIA VIA_K7 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:6 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0]
trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x3]
trigger[0x3])
Using ACPI (MADT) for SMP configuration information
Building zonelist for node : 0
Kernel command line: auto BOOT_IMAGE=L ro root=303
Initializing CPU#0
Detected 1733.291 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3416.06 BogoMIPS
Memory: 256232k/262080k available (1605k kernel code, 5144k reserved, 530k
data, 120k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
-> /dev
-> /dev/console
-> /root
CPU: Before vendor init, caps: 0383fbff c1c3fbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Machine check exception polling timer started.
CPU: AMD Athlon(tm) XP 2100+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000080
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23
not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 1 1 0 1 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1733.0100 MHz.
..... host bus clock speed is 266.0630 MHz.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
mtrr: v2.0 (20020519)
device class 'cpu': registering
device class cpu: adding driver system:cpu
PCI: Using configuration type 1
device class cpu: adding device CPU 0
interfaces: adding device CPU 0
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec pool[0]: 1 bvecs: 256 entries (12 bytes)
biovec pool[1]: 4 bvecs: 256 entries (48 bytes)
biovec pool[2]: 16 bvecs: 256 entries (192 bytes)
biovec pool[3]: 64 bvecs: 256 entries (768 bytes)
biovec pool[4]: 128 bvecs: 256 entries (1536 bytes)
biovec pool[5]: 256 bvecs: 256 entries (3072 bytes)
ACPI: Subsystem revision 20021212
ACPI-0263: *** Info: GPE Block0 defined as GPE0 to GPE15
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.93 (c) Adam Belay
PnPBIOS: Found PnP BIOS installation structure at 0xc00f79a0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x686b, dseg 0xf0000
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
block request queues:
128 requests per read queue
128 requests per write queue
8 requests per batch
enter congestion at 31
exit congestion at 33
SCSI subsystem driver Revision: 1.00
device class 'scsi-host': registering
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16)
00:00:01[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17)
00:00:01[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xb9 -> IRQ 22)
00:00:11[C] -> 2-22 -> IRQ 22
Pin 2-16 already programmed
Pin 2-17 already programmed
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xc1 -> IRQ 18)
00:00:05[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc9 -> IRQ 19)
00:00:05[D] -> 2-19 -> IRQ 19
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd1 -> IRQ 21)
00:00:10[A] -> 2-21 -> IRQ 21
Pin 2-21 already programmed
Pin 2-21 already programmed
Pin 2-21 already programmed
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xd9 -> IRQ 23)
00:00:12[A] -> 2-23 -> IRQ 23
Pin 2-18 already programmed
ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even
'acpi=off'
aio_setup: sizeof(struct page) = 40
devfs: v1.22 (20021013) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
PCI: Via IRQ fixup for 00:10.0, from 11 to 5
PCI: Via IRQ fixup for 00:10.1, from 10 to 5
PCI: Via IRQ fixup for 00:10.2, from 3 to 5
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU1] (supports C1, 16 throttling states)
Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled
tts/0 at I/O 0x3f8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
Linux agpgart interface v1.0 (c) Dave Jones
agpgart: Detected VIA Apollo Pro KT400 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 128M @ 0xe0000000
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
via-rhine.c:v1.10-LK1.1.15 November-22-2002 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth0: VIA VT6102 Rhine-II at 0xdfffee00, 00:10:dc:a6:b2:44, IRQ 23.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
hda: IC35L080AVVA07-0, ATA DISK drive
hda: DMA disabled
hda: bad special flag: 0x03
hda: tagged command queueing enabled, command queue depth 32
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: host protected area => 1
hda: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=159560/16/63,
UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
scsi HBA driver <NULL> didn't set max_sectors, please fix the template
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
(scsi0:A:1): 20.000MB/s transfers (20.000MHz, offset 7)
Vendor: YAMAHA Model: CRW2100S Rev: 1.0N
Type: CD-ROM ANSI SCSI revision: 02
(scsi0:A:2): 20.000MB/s transfers (20.000MHz, offset 15)
Vendor: PLEXTOR Model: CD-ROM PX-40TS Rev: 1.05
Type: CD-ROM ANSI SCSI revision: 02
scsi HBA driver Qlogic ISP 1280/12160 didn't set max_sectors, please fix the
template
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 1, lun 0
sr1: scsi-1 drive
Attached scsi CD-ROM sr1 at scsi0, channel 0, id 2, lun 0
device class 'input': registering
register interface 'mouse' with class 'input'
mice: PS/2 mouse device common for all mice
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 120k freed
Adding 88348k swap on /dev/ide/host0/bus0/target0/lun0/part4. Priority:-1
extents:1
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.
^ permalink raw reply [flat|nested] 2+ messages in thread
* WARNING: unexpected IO-APIC, please mail ...
@ 2003-11-25 8:14 Pawel Niewiadomski
0 siblings, 0 replies; 2+ messages in thread
From: Pawel Niewiadomski @ 2003-11-25 8:14 UTC (permalink / raw)
To: linux-smp
Probably you've seen this already, but I'm sending it. It's dmesg output
with warning included:
d[1])
CPU 1 (0x0100) enabledProcessor #1 Pentium 4(tm) XEON(tm) APIC version 16
IOAPIC (id[0x2] address[0xfec00000] global_irq_base[0x0])
IOAPIC (id[0x3] address[0xfec80000] global_irq_base[0x18])
IOAPIC (id[0x4] address[0xfec80400] global_irq_base[0x30])
INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x1] trigger[0x1])
INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
LAPIC_NMI (acpi_id[0x0000] polarity[0x1] trigger[0x1] lint[0x1])
LAPIC_NMI (acpi_id[0x0001] polarity[0x1] trigger[0x1] lint[0x1])
2 CPUs total
Local APIC address fee00000
__va_range(0x1fefefd8, 0x24): idx=8 mapped at ffff6000
__va_range(0x1fefefd8, 0x28): idx=8 mapped at ffff6000
ACPI table found: BOOT v1 [PTLTD $SBFTBL$ 1540.0]
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: Product ID: SE7500CW2 APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
I/O APIC #3 Version 32 at 0xFEC80000.
I/O APIC #4 Version 32 at 0xFEC80400.
Processors: 2
Kernel command line: auto BOOT_IMAGE=20 ro root=802
Initializing CPU#0
Detected 2392.312 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4771.02 BogoMIPS
Memory: 515404k/523776k available (1161k kernel code, 7904k reserved, 483k data, 100k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU0: Intel(R) Xeon(TM) CPU 2.40GHz stepping 07
per-CPU timeslice cutoff: 1462.89 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 2000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 4784.12 BogoMIPS
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check reporting enabled on CPU#1.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU1: Intel(R) Xeon(TM) CPU 2.40GHz stepping 07
Total of 2 processors activated (9555.14 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
Setting 3 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 3 ... ok.
Setting 4 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 4 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-18, 3-0, 3-1, 3-2, 3-3, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11, 3-12, 3-13, 3-14, 3-15, 3-16, 3-17, 3-18, 3-19, 3-20, 3-21, 3-22, 3-23, 4-0, 4-1, 4-2, 4-3, 4-4, 4-5, 4-6, 4-7, 4-8, 4-9, 4-10, 4-11, 4-12, 4-13, 4-14, 4-15, 4-16, 4-17, 4-18, 4-19, 4-20, 4-21, 4-22, 4-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 22.
number of IO-APIC #2 registers: 24.
number of IO-APIC #3 registers: 24.
number of IO-APIC #4 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02008000
....... : physical APIC id: 02
WARNING: unexpected IO-APIC, please mail
to linux-smp@vger.kernel.org
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 003 03 0 0 0 0 0 1 1 39
02 003 03 0 0 0 0 0 1 1 31
03 003 03 0 0 0 0 0 1 1 41
04 003 03 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 003 03 0 0 0 0 0 1 1 51
07 003 03 0 0 0 0 0 1 1 59
08 003 03 0 0 0 0 0 1 1 61
09 003 03 0 0 0 0 0 1 1 69
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 003 03 0 0 0 0 0 1 1 71
0d 003 03 0 0 0 0 0 1 1 79
0e 003 03 0 0 0 0 0 1 1 81
0f 003 03 0 0 0 0 0 1 1 89
10 003 03 1 1 0 1 0 1 1 91
11 003 03 1 1 0 1 0 1 1 99
12 000 00 1 0 0 0 0 0 0 00
13 003 03 1 1 0 1 0 1 1 A1
14 003 03 1 1 0 1 0 1 1 A9
15 003 03 1 1 0 1 0 1 1 B1
16 003 03 1 1 0 1 0 1 1 B9
17 003 03 1 1 0 1 0 1 1 C1
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 03000000
....... : arbitration: 03
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 003 03 1 1 0 1 0 1 1 C9
05 003 03 1 1 0 1 0 1 1 D1
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #4......
.... register #00: 04000000
....... : physical APIC id: 04
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 04000000
....... : arbitration: 04
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
IRQ28 -> 1:4
IRQ29 -> 1:5
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2392.3115 MHz.
..... host bus clock speed is 99.6795 MHz.
cpu: 0, clocks: 996795, slice: 332265
CPU0<T0:996784,T1:664512,D:7,S:332265,C:996795>
cpu: 1, clocks: 996795, slice: 332265
CPU1<T0:996784,T1:332240,D:14,S:332265,C:996795>
checking TSC synchronization across CPUs: passed.
Waiting on wait_init_idle (map = 0x2)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfd921, last bus=4
PCI: Using configuration type 1
PCI: Probing PCI hardware
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Using IRQ router PIIX [8086/2480] at 00:1f.0
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I31,P0) -> 17
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B2,I2,P0) -> 28
PCI->APIC IRQ transform: (B2,I2,P1) -> 29
PCI->APIC IRQ transform: (B4,I3,P0) -> 21
PCI->APIC IRQ transform: (B4,I4,P0) -> 20
PCI->APIC IRQ transform: (B4,I5,P0) -> 23
PCI->APIC IRQ transform: (B4,I6,P0) -> 22
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Detected PS/2 Mouse Port.
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3: IDE controller on PCI bus 00 dev f9
ICH3: detected chipset, but driver not compiled in!
PCI: Device 00:1f.1 not available because of resource collisions
ICH3: BIOS setup was incomplete.
ICH3: chipset revision 2
ICH3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x6c60-0x6c67, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x6c68-0x6c6f, BIOS settings: hdc:pio, hdd:pio
PDC20267: IDE controller on PCI bus 04 dev 30
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
PDC20267: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER Mode.
PDC20267: neither IDE port enabled (BIOS)
hdc: HL-DT-ST CD-ROM GCR-8520B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: no supported devices found.
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.1.0
<Adaptec 39320 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.1.0
<Adaptec 39320 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
Vendor: SEAGATE Model: ST336732LW Rev: 0022
Type: Direct-Access ANSI SCSI revision: 03
(scsi1:A:0): 320.000MB/s transfers (160.000MHz DT, offset 63, 16bit)
(scsi1:A:0:1): Now packetized.
scsi1:A:0:0: Tagged Queuing enabled. Depth 32
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 71687369 512-byte hdwr sectors (36704 MB)
Partition check:
sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 >
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Setting latency timer of device 00:1d.0 to 64
uhci.c: USB UHCI at I/O 0x6c00, IRQ 16
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
uhci.c: USB UHCI at I/O 0x6c20, IRQ 19
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 100k freed
Adding Swap: 722884k swap-space (priority -1)
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
Intel(R) PRO/100 Fast Ethernet Adapter - Loadable driver, ver 1.8.38
Copyright (c) 2002 Intel Corporation
eth0: Intel(R) 8255x-based Ethernet Adapter
Mem:0xfc361000 IRQ:20 Speed:100 Mbps Dx:Full
Hardware receive checksums enabled
cpu cycle saver enabled
eth1: Intel(R) 8255x-based Ethernet Adapter
Mem:0xfc362000 IRQ:23 Speed:100 Mbps Dx:Full
Hardware receive checksums enabled
cpu cycle saver enabled
usb.c: registered new driver usbnet
keyboard: Timeout - AT keyboard not present?(f4)
Out of Memory: Killed process 21155 (httpd).
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
e100: eth0 NIC Link is Down
e100: eth1 NIC Link is Down
e100: eth1 NIC Link is Up 100 Mbps Full duplex
sending pkt_too_big (len[1500] pmtu[1464]) to self
sending pkt_too_big (len[1500] pmtu[1464]) to self
sending pkt_too_big (len[1500] pmtu[1464]) to self
sending pkt_too_big (len[1500] pmtu[1464]) to self
sending pkt_too_big (len[1500] pmtu[1464]) to self
sending pkt_too_big (len[1500] pmtu[1464]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
sending pkt_too_big (len[1500] pmtu[576]) to self
e100: eth1 NIC Link is Down
e100: eth1 NIC Link is Up 100 Mbps Full duplex
--
Pawe³ Niewiadomski,
paweln()iidea.pl, http://iidea.pl/~paweln/, GG:3107227
Podrêczniki SAG,LPG-> http://www.linuxpl.org/{SAG,LPG} <-wersje przet³umaczone
Author of: Virtual Qmail, qmail-patches
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2003-11-25 8:14 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2002-12-17 14:19 WARNING: unexpected IO-APIC, please mail Sebastian Frei
-- strict thread matches above, loose matches on Subject: below --
2003-11-25 8:14 Pawel Niewiadomski
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox