Problems recording sound with ISAPnp Soundcard since Kernel-2.4.x

Problems recording sound with ISAPnp Soundcard since Kernel-2.4.x

[Magic Phibo]

Hello 

Sorry, if this mail arrives twice ...

Since upgrade to Kernel-2.4.x (currently 2.4.10) I got problems recording sound
causing following error message in /var/log/messages:

Sep 30 15:53:16 osiris kernel: Sound: DMA (input) timed out - IRQ/DRQ configerror?

It's a redhat dist. (7.0) with a Yamaha ISAPnp Soundcard (OPL3 YMF719) and a
self configured Kernel-2.4.10.

With 2.2-Kernels and the isapnp tools (pnpdump/isapnp) the soundcard worked
fine. But with the same isapnp.conf and module parameters (irq,ioports,dma) and 
Kernel-2.4.x the soundcard is recognized, modules are loaded successfully and
any kind of soundfiles can be played, but recording like

'rec /tmp/soundfile.au' oder 'cat > /tmp/soundfile.au < /dev/audio'

does NOT work anymore.

I also tried the new isapnp support (included since Kernel-2.4.x) as module or
directly in the kernel. Here is the output of 'dmesg':

isapnp: Scanning for PnP cards...
isapnp: Card 'OPL3-SA3 Sound Board'
isapnp: 1 Plug & Play card detected total 
ad1848/cs4248 codec driver Copyright (C) by Hannu Savolainen 1993-1996
ad1848: No ISAPnP cards found, trying standard ones...
opl3sa2: Activated ISA PnP card 0 (active=1)
opl3sa2: chipset version = 0x4
opl3sa2: Found OPL3-SA3 (YMF715E or YMF719E)
<OPL3-SA3> at 0x100
<MS Sound System (CS4231)> at 0xe84 irq 5 dma 1,3
<MPU-401 0.0  Midi interface #1> at 0x300 irq 5
opl3sa2: 1 PnP card(s) found.
YM3812 and OPL-3 driver Copyright (C) by Hannu Savolainen, Rob Hooft 1993-1996
<Yamaha OPL3> at 0x388

Here the contents of /proc/isapnp:

Card 1 'YMH0800:OPL3-SA3 Sound Board' PnP version 1.0  Logical device 0
'YMH0021:Unknown' Device is active
Active port 0x240,0xe80,0x388,0x300,0x100
Active IRQ 5 [0x2]
Active DMA 1,3
Resources 0
Priority preferred
Port 0x220-0x220, align 0xf, size 0x10, 16-bit address decoding
Port 0x530-0x530, align 0x7, size 0x8, 16-bit address decoding
Port 0x388-0x388, align 0x7, size 0x8, 16-bit address decoding
Port 0x330-0x330, align 0x1, size 0x2, 16-bit address decoding
Port 0x370-0x370, align 0x1, size 0x2, 16-bit address decoding
IRQ 5 High-Edge
DMA 0 8-bit byte-count type-A
DMA 1 8-bit byte-count type-A
Alternate resources 0:1
Priority acceptable
Port 0x240-0x240, align 0xf, size 0x10, 16-bit address decoding
Port 0xe80-0xe80, align 0x7, size 0x8, 16-bit address decoding
Port 0x388-0x388, align 0x7, size 0x8, 16-bit address decoding
Port 0x300-0x300, align 0x1, size 0x2, 16-bit address decoding
Port 0x100-0xffe, align 0x1, size 0x2, 16-bit address decoding
IRQ 5,7,2/9,10,11 High-Edge
DMA 0,1,3 8-bit byte-count type-A
DMA 0,1,3 8-bit byte-count type-A
Alternate resources 0:2
Priority functional
Port 0x220-0x280, align 0xf, size 0x10, 16-bit address decoding
Port 0x530-0xf48, align 0x7, size 0x8, 16-bit address decoding
Port 0x388-0x3f8, align 0x7, size 0x8, 16-bit address decoding
Port 0x300-0x334, align 0x1, size 0x2, 16-bit address decoding
Port 0x100-0xffe, align 0x1, size 0x2, 16-bit address decoding
IRQ 3,5,7,2/9,10,11 High-Edge
DMA 0,1,3 8-bit byte-count type-A
DMA 0,1,3 8-bit byte-count type-A
Logical device 1 'YMH0022:Unknown'
Compatible device PNPb02f
Device is not active
Active DMA 0,0
Resources 0
Priority preferred
Port 0x201-0x201, align 0x0, size 0x1, 16-bit address decoding
Alternate resources 0:1
Priority acceptable
Port 0x202-0x202, align 0x0, size 0x1, 16-bit address decoding
Alternate resources 0:2
Priority acceptable
Port 0x203-0x203, align 0x0, size 0x1, 16-bit address decoding
Alternate resources 0:3
Priority acceptable
Port 0x204-0x20f, align 0x0, size 0x1, 16-bit address decoding 

The result is just the same: card recognized, modules loaded, soundfiles
can be played, but NO recording causing the same error message as 
mentioned above.

Here is my /etc/isapnp.conf (for the isapnp tools without isapnp support
in the kernel):

(READPORT 0x0273)
(ISOLATE PRESERVE)
(IDENTIFY *)
(VERBOSITY 2)
(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
(CONFIGURE YMH0800/-1 (LD 0
(IO 0 (SIZE 16) (BASE 0x0220))
(IO 1 (SIZE 8) (BASE 0x0530))
(IO 2 (SIZE 8) (BASE 0x0388))
(IO 3 (SIZE 2) (BASE 0x0330))
(IO 4 (SIZE 2) (BASE 0x0370))
(INT 0 (IRQ 5 (MODE +E))) 
(DMA 0 (CHANNEL 0))
(DMA 1 (CHANNEL 1))
(NAME "YMH0800/-1[0]{OPL3-SA3 Sound Board}")
(ACT Y)
))
(CONFIGURE YMH0800/-1 (LD 1
(IO 0 (SIZE 1) (BASE 0x0201))
(NAME "YMH0800/-1[1]{OPL3-SA3 Sound Board}")
(ACT Y)
))
(WAITFORKEY)

And my /etc/modules.conf:

alias sound-slot-0 opl3sa2
options sound dmabuf=1
alias midi opl3
options opl3 io=0x388
options opl3sa2 mss_io=0x530 irq=5 dma=0 dma2=1 mpu_io=0x330 io=0x370

I also tried different dma channels (dma=1 dma2=3) leading to the same result. 
Moreover I checked another ISAPnp soundcard (Soundblaster), which also
worked perfectly with Kernel-2.2.x, but with Kernel-2.4.x it's behaviour is just
the same as with the Yamaha soundcard: card recognized, modules loaded
successfully, soundfiles can be played but NO recording !!!

What can I try else or did I forget anything ?

Thanks in advance for your help !


Cheers,
Phibo

Re: Problems recording sound with ISAPnp Soundcard since Kernel-2.4.x

[Bill Nottingham]

Magic Phibo (phibo@gmx.li) said: 
> I also tried the new isapnp support (included since Kernel-2.4.x) as module or
> directly in the kernel. Here is the output of 'dmesg':

If you use the new isapnp support, make sure you do *not* use
userland ISAPnP at the same time. They don't mix.

Bill

Re: Problems recording sound with ISAPnp Soundcard since Kernel-2.4.x

[Magic Phibo]

On Thu, 04 Oct 2001, Bill Nottingham wrote:
>Magic Phibo (phibo@gmx.li) said: 
>> I also tried the new isapnp support (included since Kernel-2.4.x) as module or
>> directly in the kernel. Here is the output of 'dmesg':
>
>If you use the new isapnp support, make sure you do *not* use
>userland ISAPnP at the same time. They don't mix.
>

Yes I know and didn't mix them. I included a check for existence of
/proc/isapnp before execution of the userland ISAPnp in the rc-script
/etc/rc.d/rc.sysinit. So, if isapnp support is included in the kernel, the file
/proc/isapnp is created upon detection of the ISAPnp card and therefore,
the userland ISAPnp won't be executed.

Thanks anyway !


Cheers,
Phibo

Re: Problems recording sound with ISAPnp Soundcard since Kernel-2.4.x

[Jérôme Augé]

[-- Attachment #1: Type: text/plain, Size: 733 bytes --]

Magic Phibo wrote:
> 
> Hello
> 
> Sorry, if this mail arrives twice ...
> 
> Since upgrade to Kernel-2.4.x (currently 2.4.10) I got problems recording sound
> causing following error message in /var/log/messages:
> 
> Sep 30 15:53:16 osiris kernel: Sound: DMA (input) timed out - IRQ/DRQ configerror?
> 
> It's a redhat dist. (7.0) with a Yamaha ISAPnp Soundcard (OPL3 YMF719) and a
> self configured Kernel-2.4.10.
> 
> [...]
> 

I also noticed this problem ...
There is a problem with the initialization of the DMA channels (dma and
dma2 are never set to the real dma channels, and they remain at -1).
Applying this patch fix this error.

I'm going to post it to the kernel mailling list.

-- 
Jérôme Augé

[-- Attachment #2: patch-opl3sa2-dma-init --]
[-- Type: text/plain, Size: 924 bytes --]

diff -ur linux.orig/drivers/sound/opl3sa2.c linux/drivers/sound/opl3sa2.c
--- linux.orig/drivers/sound/opl3sa2.c	Wed Oct  3 09:36:16 2001
+++ linux/drivers/sound/opl3sa2.c	Wed Oct  3 09:41:28 2001
@@ -862,9 +862,9 @@
 
 	/* Our own config: */
 	hw_cfg->io_base = dev->resource[4].start;
-	hw_cfg->irq     = 0;
-	hw_cfg->dma     = -1;
-	hw_cfg->dma2    = -1;
+	hw_cfg->irq     = dev->irq_resource[0].start;
+	hw_cfg->dma     = dev->dma_resource[0].start;
+	hw_cfg->dma2    = dev->dma_resource[1].start;
 	
 	/* The MSS config: */
 	mss_cfg->io_base      = dev->resource[1].start;
@@ -944,9 +944,9 @@
 			 *  give pretty output from conf_printf. :)
 			 */
 			cfg[card].io_base = io;
-			cfg[card].irq     = 0;
-			cfg[card].dma     = -1;
-			cfg[card].dma2    = -1;
+			cfg[card].irq     = irq;
+			cfg[card].dma     = dma;
+			cfg[card].dma2    = dma2;
 	
 			/* The MSS config: */
 			cfg_mss[card].io_base      = mss_io;

Re: Problems recording sound with ISAPnp Soundcard since Kernel-2.4.x

[Magic Phibo]

[-- Attachment #1: Type: text/plain, Size: 700 bytes --]

>> Since upgrade to Kernel-2.4.x (currently 2.4.10) I got problems recording sound
>> causing following error message in /var/log/messages:
>> 
>> Sep 30 15:53:16 osiris kernel: Sound: DMA (input) timed out - IRQ/DRQ configerror?
>> 
>> It's a redhat dist. (7.0) with a Yamaha ISAPnp Soundcard (OPL3 YMF719) and a
>> self configured Kernel-2.4.10.
>> 
>> [...]
>> 
>
>I also noticed this problem ...
>There is a problem with the initialization of the DMA channels (dma and
>dma2 are never set to the real dma channels, and they remain at -1).
>Applying this patch fix this error.
>
> [...]

I applied this patch and now recording works fine. So, the problem is fixed !

Thanks a lot !


Cheers,
Phibo

[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: patch-kernel2.4.x-opl3sa2-dma-init --]
[-- Type: text/x-c; name="patch-kernel2.4.x-opl3sa2-dma-init", Size: 924 bytes --]

diff -ur linux.orig/drivers/sound/opl3sa2.c linux/drivers/sound/opl3sa2.c
--- linux.orig/drivers/sound/opl3sa2.c	Wed Oct  3 09:36:16 2001
+++ linux/drivers/sound/opl3sa2.c	Wed Oct  3 09:41:28 2001
@@ -862,9 +862,9 @@
 
 	/* Our own config: */
 	hw_cfg->io_base = dev->resource[4].start;
-	hw_cfg->irq     = 0;
-	hw_cfg->dma     = -1;
-	hw_cfg->dma2    = -1;
+	hw_cfg->irq     = dev->irq_resource[0].start;
+	hw_cfg->dma     = dev->dma_resource[0].start;
+	hw_cfg->dma2    = dev->dma_resource[1].start;
 	
 	/* The MSS config: */
 	mss_cfg->io_base      = dev->resource[1].start;
@@ -944,9 +944,9 @@
 			 *  give pretty output from conf_printf. :)
 			 */
 			cfg[card].io_base = io;
-			cfg[card].irq     = 0;
-			cfg[card].dma     = -1;
-			cfg[card].dma2    = -1;
+			cfg[card].irq     = irq;
+			cfg[card].dma     = dma;
+			cfg[card].dma2    = dma2;
 	
 			/* The MSS config: */
 			cfg_mss[card].io_base      = mss_io;