From: Andre Przywara <andre.przywara@arm.com>
To: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Mikhail Kalashnikov <iuncuim@gmail.com>,
u-boot@lists.denx.de, linux-sunxi@lists.linux.dev
Subject: [PATCH 31/34] sunxi: A523: add DDR3 DRAM support
Date: Sun, 23 Mar 2025 11:35:41 +0000 [thread overview]
Message-ID: <20250323113544.7933-32-andre.przywara@arm.com> (raw)
In-Reply-To: <20250323113544.7933-1-andre.przywara@arm.com>
From: Mikhail Kalashnikov <iuncuim@gmail.com>
Add reverse engineered code to add support for DDR3 DRAM chips on the
Allwinner A523 DRAM controller.
---
arch/arm/mach-sunxi/Kconfig | 8 ++
arch/arm/mach-sunxi/dram_sun55i_a523.c | 136 ++++++++++++++++++-
arch/arm/mach-sunxi/dram_timings/Makefile | 1 +
arch/arm/mach-sunxi/dram_timings/a523_ddr3.c | 135 ++++++++++++++++++
4 files changed, 274 insertions(+), 6 deletions(-)
create mode 100644 arch/arm/mach-sunxi/dram_timings/a523_ddr3.c
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index aeab2b3f6dd..345e685fc4b 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -596,6 +596,14 @@ config SUNXI_DRAM_DDR2_V3S
This option is only for the DDR2 memory chip which is co-packaged in
Allwinner V3s SoC.
+config SUNXI_DRAM_A523_DDR3
+ bool "DDR3 DRAM chips on the A523/T527 DRAM controller"
+ select SUNXI_DRAM_DDR3
+ depends on DRAM_SUN55I_A523
+ help
+ This option is the DDR3 timing used by the stock boot0 by
+ Allwinner.
+
config SUNXI_DRAM_A523_LPDDR4
bool "LPDDR4 DRAM chips on the A523/T527 DRAM controller"
select SUNXI_DRAM_LPDDR4
diff --git a/arch/arm/mach-sunxi/dram_sun55i_a523.c b/arch/arm/mach-sunxi/dram_sun55i_a523.c
index fae02062547..d5e3a2fa0eb 100644
--- a/arch/arm/mach-sunxi/dram_sun55i_a523.c
+++ b/arch/arm/mach-sunxi/dram_sun55i_a523.c
@@ -870,6 +870,24 @@ static void mctl_phy_ca_bit_delay_compensation(const struct dram_para *para,
clrbits_le32(SUNXI_DRAM_PHY0_BASE + 0x48, 0xc0000000);
switch (para->type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ case SUNXI_DRAM_TYPE_DDR4:
+ case SUNXI_DRAM_TYPE_LPDDR3:
+ low = val & 0xff;
+ high = (val >> 8) & 0xff;
+
+ val = (high << 24) | (high << 16) | (high << 8) | high;
+ writel(val, SUNXI_DRAM_PHY0_BASE + 0x104);
+ writel(val, SUNXI_DRAM_PHY0_BASE + 0x108);
+ writel(val, SUNXI_DRAM_PHY0_BASE + 0x10c);
+ writel(val, SUNXI_DRAM_PHY0_BASE + 0x114);
+ writel(val, SUNXI_DRAM_PHY0_BASE + 0x118);
+ writel(val, SUNXI_DRAM_PHY0_BASE + 0x11c);
+ writel(val, SUNXI_DRAM_PHY0_BASE + 0x120);
+
+ val = (low << 24) | (low << 16) | (high << 8) | high;
+ writel(val, SUNXI_DRAM_PHY0_BASE + 0x11c);
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
low = val & 0xff;
high = (val >> 8) & 0xff;
@@ -921,6 +939,26 @@ static bool mctl_phy_init(const struct dram_para *para,
clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x00, 0xf00, val);
switch (para->type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ val = 9;
+ val2 = 13;
+ break;
+ case SUNXI_DRAM_TYPE_DDR4:
+ if (config->clk <= 936) {
+ val = 10;
+ val2 = 14;
+ } else if (config->clk <= 1200) {
+ val = 12;
+ val2 = 16;
+ } else {
+ val = 14;
+ val2 = 18;
+ }
+ break;
+ case SUNXI_DRAM_TYPE_LPDDR3:
+ val = 8;
+ val2 = 14;
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
if (config->clk <= 936) {
val = 10;
@@ -942,6 +980,36 @@ static bool mctl_phy_init(const struct dram_para *para,
writel(0, SUNXI_DRAM_PHY0_BASE + 0x08);
switch (para->type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ writel(0x150a0310, SUNXI_DRAM_PHY0_BASE + 0x54);
+ writel(0x13140816, SUNXI_DRAM_PHY0_BASE + 0x58);
+ writel(0x001c0d1b, SUNXI_DRAM_PHY0_BASE + 0x5c);
+ writel(0x050c1d1a, SUNXI_DRAM_PHY0_BASE + 0x60);
+ writel(0x0411060b, SUNXI_DRAM_PHY0_BASE + 0x64);
+ writel(0x09071217, SUNXI_DRAM_PHY0_BASE + 0x68);
+ writel(0x18190e01, SUNXI_DRAM_PHY0_BASE + 0x6c);
+ writel(0x020f1e00, SUNXI_DRAM_PHY0_BASE + 0x70);
+ break;
+ case SUNXI_DRAM_TYPE_DDR4:
+ writel(0x090c1c14, SUNXI_DRAM_PHY0_BASE + 0x54);
+ writel(0x1300060f, SUNXI_DRAM_PHY0_BASE + 0x58);
+ writel(0x12030807, SUNXI_DRAM_PHY0_BASE + 0x5c);
+ writel(0x0b100a02, SUNXI_DRAM_PHY0_BASE + 0x60);
+ writel(0x1a110e05, SUNXI_DRAM_PHY0_BASE + 0x64);
+ writel(0x0d041617, SUNXI_DRAM_PHY0_BASE + 0x68);
+ writel(0x1819011b, SUNXI_DRAM_PHY0_BASE + 0x6c);
+ writel(0x151d1e00, SUNXI_DRAM_PHY0_BASE + 0x70);
+ break;
+ case SUNXI_DRAM_TYPE_LPDDR3:
+ writel(0x010a1a0f, SUNXI_DRAM_PHY0_BASE + 0x54);
+ writel(0x10081b07, SUNXI_DRAM_PHY0_BASE + 0x58);
+ writel(0x11061c12, SUNXI_DRAM_PHY0_BASE + 0x5c);
+ writel(0x00131409, SUNXI_DRAM_PHY0_BASE + 0x60);
+ writel(0x15030e16, SUNXI_DRAM_PHY0_BASE + 0x64);
+ writel(0x0b0c0d17, SUNXI_DRAM_PHY0_BASE + 0x68);
+ writel(0x18190204, SUNXI_DRAM_PHY0_BASE + 0x6c);
+ writel(0x051d1e00, SUNXI_DRAM_PHY0_BASE + 0x70);
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
writel(0x00010203, SUNXI_DRAM_PHY0_BASE + 0x54);
writel(0x04050607, SUNXI_DRAM_PHY0_BASE + 0x58);
@@ -962,6 +1030,15 @@ static bool mctl_phy_init(const struct dram_para *para,
mctl_phy_ca_bit_delay_compensation(para, config);
switch (para->type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ val = 0x2bbd4900;
+ break;
+ case SUNXI_DRAM_TYPE_DDR4:
+ val = 0x3841b800;
+ break;
+ case SUNXI_DRAM_TYPE_LPDDR3:
+ val = 0x19016300;
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
val = 0x18fd6300;
break;
@@ -973,6 +1050,15 @@ static bool mctl_phy_init(const struct dram_para *para,
clrbits_le32(SUNXI_DRAM_PHY0_BASE + 0x00, 0x70);
switch (para->type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ val = 0x20;
+ break;
+ case SUNXI_DRAM_TYPE_DDR4:
+ val = 0x40;
+ break;
+ case SUNXI_DRAM_TYPE_LPDDR3:
+ val = 0x30;
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
val = 0x50;
break;
@@ -1003,17 +1089,22 @@ static bool mctl_phy_init(const struct dram_para *para,
udelay(10);
switch (para->type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ val = para->tpr6 & 0xff;
+ break;
+ case SUNXI_DRAM_TYPE_DDR4:
+ val = para->tpr6 >> 8 & 0xff;
+ break;
+ case SUNXI_DRAM_TYPE_LPDDR3:
+ val = para->tpr6 >> 16 & 0xff;
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
- val = para->tpr6 >> 24 & 0xff;
- if (val)
- val <<= 1;
- else
- val = 0x33;
+ val = para->tpr6 >> 24;
break;
default:
panic("This DRAM setup is currently not supported.\n");
};
- val <<= 23;
+ val <<= 24;
clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x300, 0xff800060, val | 0x40);
clrsetbits_le32(SUNXI_DRAM_PHY0_BASE + 0x600, 0xff800060, val | 0x40);
@@ -1078,6 +1169,23 @@ static bool mctl_phy_init(const struct dram_para *para,
mctl_await_completion(&mctl_ctl->swstat, 1, 1);
switch (para->type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ writel(0x1f14, &mctl_ctl->mrctrl1);
+ writel(0x800000f0, &mctl_ctl->mrctrl0);
+ mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+ writel(4, &mctl_ctl->mrctrl1);
+ writel(0x800010f0, &mctl_ctl->mrctrl0);
+ mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+ writel(0x20, &mctl_ctl->mrctrl1);
+ writel(0x800020f0, &mctl_ctl->mrctrl0);
+ mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+
+ writel(0, &mctl_ctl->mrctrl1);
+ writel(0x800030f0, &mctl_ctl->mrctrl0);
+ mctl_await_completion(&mctl_ctl->mrctrl0, BIT(31), 0);
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
if (config->clk <= 936) {
mr1 = 0x34;
@@ -1209,6 +1317,9 @@ static bool mctl_ctrl_init(const struct dram_para *para,
reg_val = MSTR_ACTIVE_RANKS(config->ranks);
switch (para->type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ reg_val |= MSTR_BURST_LENGTH(8) | MSTR_DEVICETYPE_DDR3 | MSTR_2TMODE;
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
reg_val |= MSTR_BURST_LENGTH(16) | MSTR_DEVICETYPE_LPDDR4;
break;
@@ -1227,6 +1338,9 @@ static bool mctl_ctrl_init(const struct dram_para *para,
writel(0x0201, &mctl_ctl->odtmap);
switch (para->type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ reg_val = 0x06000400;
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
reg_val = 0x04000400;
break;
@@ -1361,7 +1475,11 @@ static unsigned long long mctl_calc_size(const struct dram_config *config)
}
static const struct dram_para para = {
+#ifdef CONFIG_SUNXI_DRAM_A523_DDR3
+ .type = SUNXI_DRAM_TYPE_DDR3,
+#elif defined(CONFIG_SUNXI_DRAM_A523_LPDDR4)
.type = SUNXI_DRAM_TYPE_LPDDR4,
+#endif
.dx_odt = CONFIG_DRAM_SUNXI_DX_ODT,
.dx_dri = CONFIG_DRAM_SUNXI_DX_DRI,
.ca_dri = CONFIG_DRAM_SUNXI_CA_DRI,
@@ -1435,6 +1553,12 @@ unsigned long sunxi_dram_init(void)
config.clk = 360;
switch (para.type) {
+ case SUNXI_DRAM_TYPE_DDR3:
+ config.odt_en = 0x90909090;
+ config.tpr11 = 0x8f919190;
+ config.tpr12 = 0x22222723;
+ config.tpr14 = 0x48484848;
+ break;
case SUNXI_DRAM_TYPE_LPDDR4:
config.odt_en = 0x84848484;
config.tpr11 = 0x9a9a9a9a;
diff --git a/arch/arm/mach-sunxi/dram_timings/Makefile b/arch/arm/mach-sunxi/dram_timings/Makefile
index 7bcda180d0a..7f1ee96b864 100644
--- a/arch/arm/mach-sunxi/dram_timings/Makefile
+++ b/arch/arm/mach-sunxi/dram_timings/Makefile
@@ -6,4 +6,5 @@ obj-$(CONFIG_SUNXI_DRAM_H6_DDR3_1333) += h6_ddr3_1333.o
obj-$(CONFIG_SUNXI_DRAM_H616_DDR3_1333) += h616_ddr3_1333.o
obj-$(CONFIG_SUNXI_DRAM_H616_LPDDR3) += h616_lpddr3.o
obj-$(CONFIG_SUNXI_DRAM_H616_LPDDR4) += h616_lpddr4_2133.o
+obj-$(CONFIG_SUNXI_DRAM_A523_DDR3) += a523_ddr3.o
obj-$(CONFIG_SUNXI_DRAM_A523_LPDDR4) += a523_lpddr4.o
diff --git a/arch/arm/mach-sunxi/dram_timings/a523_ddr3.c b/arch/arm/mach-sunxi/dram_timings/a523_ddr3.c
new file mode 100644
index 00000000000..b9fa5a89dd1
--- /dev/null
+++ b/arch/arm/mach-sunxi/dram_timings/a523_ddr3.c
@@ -0,0 +1,135 @@
+/*
+ * sun55i A523 DDR3 timings, as programmed by Allwinner's boot0
+ *
+ * (C) Copyright 2024 Mikhail Kalashnikov <iuncuim@gmail.com>
+ * Based on H6 DDR3 timings:
+ * (C) Copyright 2020 Jernej Skrabec <jernej.skrabec@siol.net>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/dram.h>
+#include <asm/arch/cpu.h>
+
+void mctl_set_timing_params(u32 clk)
+{
+ struct sunxi_mctl_ctl_reg * const mctl_ctl =
+ (struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
+ u8 tcl, tcwl, t_rdata_en, trtp, twr, tphy_wrlat;
+ unsigned int mr1, mr2;
+
+ u8 tccd = 4;
+ u8 tfaw = ns_to_t(40, clk);
+ u8 trrd = max(ns_to_t(10, clk), 2);
+ u8 twtr = max(ns_to_t(10, clk), 4);
+ u8 trcd = max(ns_to_t(18, clk), 2);
+ u8 trc = ns_to_t(65, clk);
+ u8 txp = max(ns_to_t(8, clk), 2);
+ u8 trp = ns_to_t(21, clk);
+ u8 tras = ns_to_t(42, clk);
+ u16 trefi = ns_to_t(3904, clk) / 32;
+ u16 trfc = ns_to_t(280, clk);
+ u16 txsr = ns_to_t(290, clk);
+
+ u8 tmrw = max(ns_to_t(14, clk), 5);
+ u8 tmod = 12;
+ u8 tcke = max(ns_to_t(15, clk), 2);
+ u8 tcksrx = max(ns_to_t(2, clk), 2);
+ u8 tcksre = max(ns_to_t(5, clk), 2);
+ u8 trasmax = (trefi * 9) / 32;
+
+ if (clk <= 936) {
+ mr1 = 0x34;
+ mr2 = 0x1b;
+ tcl = 10;
+ tcwl = 5;
+ t_rdata_en = 17;
+ trtp = 4;
+ tphy_wrlat = 5;
+ twr = 10;
+ } else if (clk <= 1200) {
+ mr1 = 0x54;
+ mr2 = 0x2d;
+ tcl = 14;
+ tcwl = 7;
+ t_rdata_en = 25;
+ trtp = 6;
+ tphy_wrlat = 9;
+ twr = 15;
+ } else {
+ mr1 = 0x64;
+ mr2 = 0x36;
+ tcl = 16;
+ tcwl = 8;
+ t_rdata_en = 29;
+ trtp = 7;
+ tphy_wrlat = 11;
+ twr = 17;
+ }
+
+ u8 tmrd = tmrw;
+ u8 tckesr = tcke;
+ u8 twtp = twr + 9 + tcwl;
+ u8 twr2rd = twtr + 9 + tcwl;
+ u8 trd2wr = ns_to_t(4, clk) + 7 - ns_to_t(1, clk) + tcl;
+ u8 txs = 4;
+ u8 txsdll = 16;
+ u8 txsabort = 4;
+ u8 txsfast = 4;
+
+ /* set DRAM timing */
+ // writel((twtp << 24) | (tfaw << 16) | (trasmax << 8) | tras,
+ // &mctl_ctl->dramtmg[0]);
+ // writel((txp << 16) | (trtp << 8) | trc, &mctl_ctl->dramtmg[1]);
+ // writel((tcwl << 24) | (tcl << 16) | (trd2wr << 8) | twr2rd,
+ // &mctl_ctl->dramtmg[2]);
+ // writel((tmrw << 20) | (tmrd << 12) | tmod, &mctl_ctl->dramtmg[3]);
+ // writel((trcd << 24) | (tccd << 16) | (trrd << 8) | trp,
+ // &mctl_ctl->dramtmg[4]);
+ // writel((tcksrx << 24) | (tcksre << 16) | (tckesr << 8) | tcke,
+ // &mctl_ctl->dramtmg[5]);
+ writel(0x0e141a10, &mctl_ctl->dramtmg[0]);
+ writel(0x00040415, &mctl_ctl->dramtmg[1]);
+ writel(0x0507050b, &mctl_ctl->dramtmg[2]);
+ writel(0x0000400c, &mctl_ctl->dramtmg[3]);
+ writel(0x06020406, &mctl_ctl->dramtmg[4]);
+ writel(0x04040504, &mctl_ctl->dramtmg[5]);
+ /* Value suggested by ZynqMP manual and used by libdram */
+ writel((txp + 2) | 0x02020000, &mctl_ctl->dramtmg[6]);
+ writel((txsfast << 24) | (txsabort << 16) | (txsdll << 8) | txs,
+ &mctl_ctl->dramtmg[8]);
+ writel(0x00020208, &mctl_ctl->dramtmg[9]);
+ writel(0xE0C05, &mctl_ctl->dramtmg[10]);
+ writel(0x440C021C, &mctl_ctl->dramtmg[11]);
+ writel(8, &mctl_ctl->dramtmg[12]);
+ writel(0xA100002, &mctl_ctl->dramtmg[13]);
+ //writel(txsr, &mctl_ctl->dramtmg[14]);
+ writel(4, &mctl_ctl->dramtmg[14]);
+
+ //clrsetbits_le32(&mctl_ctl->init[0], 0xC0000FFF, 0x558);
+ clrsetbits_le32(&mctl_ctl->init[0], 0xC0000FFF, 0x156);
+ writel(0x01f20000, &mctl_ctl->init[1]);
+ //writel(0x00001705, &mctl_ctl->init[2]);
+ writel(0x00001700, &mctl_ctl->init[2]);
+ writel(0, &mctl_ctl->dfimisc);
+ //writel((mr1 << 16) | mr2, &mctl_ctl->init[3]);
+ writel(0x1f140004, &mctl_ctl->init[3]);
+ //writel(0x00330000, &mctl_ctl->init[4]);
+ //writel(0x00040072, &mctl_ctl->init[6]);
+ //writel(0x00260008, &mctl_ctl->init[7]);
+ writel(0x00200000, &mctl_ctl->init[4]);
+ writel(0, &mctl_ctl->init[6]);
+ writel(0, &mctl_ctl->init[7]);
+
+ clrsetbits_le32(&mctl_ctl->rankctl, 0xff0, 0x660);
+
+ /* Configure DFI timing */
+ //writel(tphy_wrlat | 0x2000000 | (t_rdata_en << 16) | 0x808000,
+ // &mctl_ctl->dfitmg0);
+ writel(0x02898005,&mctl_ctl->dfitmg0);
+ writel(0x100202, &mctl_ctl->dfitmg1);
+
+ /* set refresh timing */
+ //writel((trefi << 16) | trfc, &mctl_ctl->rfshtmg);
+ writel(0x008c0000, &mctl_ctl->rfshtmg);
+}
--
2.46.3
next prev parent reply other threads:[~2025-03-23 11:36 UTC|newest]
Thread overview: 59+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-03-23 11:35 [PATCH 00/34] sunxi: clock refactoring and Allwinner A523 support Andre Przywara
2025-03-23 11:35 ` [PATCH 01/34] sunxi: clock: H6: drop usage of struct sunxi_ccm_reg Andre Przywara
2025-03-23 11:56 ` Jernej Škrabec
2025-03-23 23:50 ` Andre Przywara
2025-03-23 11:35 ` [PATCH 02/34] sunxi: mmc: remove " Andre Przywara
2025-03-23 12:04 ` Jernej Škrabec
2025-03-23 11:35 ` [PATCH 03/34] sunxi: H616: dram: " Andre Przywara
2025-03-23 11:35 ` [PATCH 04/34] sunxi: H6: " Andre Przywara
2025-03-23 11:35 ` [PATCH 05/34] sunxi: clock: H6: remove " Andre Przywara
2025-03-23 11:35 ` [PATCH 06/34] sunxi: clock: H6: drop usage of struct sunxi_prcm_reg Andre Przywara
2025-03-23 11:35 ` [PATCH 07/34] sunxi: H6/H616: dram: remove " Andre Przywara
2025-03-23 11:35 ` [PATCH 08/34] sunxi: clock: H6: remove " Andre Przywara
2025-03-23 11:35 ` [PATCH 09/34] sunxi: clock: H6: unify PLL control bit definitions Andre Przywara
2025-03-23 11:35 ` [PATCH 10/34] sunxi: clock: H6: factor out clock_set_pll() Andre Przywara
2025-03-23 11:35 ` [PATCH 11/34] sunxi: clock: H6: factor out H6/H616 CPU clock setup Andre Przywara
2025-03-23 11:35 ` [PATCH 12/34] sunxi: clock: H6: add A523 CPU PLL support Andre Przywara
2025-03-23 11:35 ` [PATCH 13/34] sunxi: spl: add support for Allwinner A523 watchdog Andre Przywara
2025-03-23 12:15 ` Jernej Škrabec
2025-03-23 23:57 ` Andre Przywara
2025-03-23 11:35 ` [PATCH 14/34] dt-bindings: add Allwinner A523 CCU bindings Andre Przywara
2025-03-23 11:35 ` [PATCH 15/34] clk: sunxi: Add support for the A523 CCU Andre Przywara
2025-03-23 11:35 ` [PATCH 16/34] clk: sunxi: Add support for the A523 -R CCU Andre Przywara
2025-03-23 12:18 ` Jernej Škrabec
2025-03-24 0:37 ` Andre Przywara
2025-03-23 11:35 ` [PATCH 17/34] pinctrl: sunxi: add Allwinner A523 pinctrl description Andre Przywara
2025-03-23 11:35 ` [PATCH 18/34] sunxi: mmc: add support for Allwinner A523 MMC mod clock Andre Przywara
2025-03-23 11:35 ` [PATCH 19/34] watchdog: sunxi: add A523 support Andre Przywara
2025-03-24 8:38 ` Stefan Roese
2025-03-23 11:35 ` [PATCH 20/34] power: regulator: add AXP323 support Andre Przywara
2025-03-23 11:35 ` [PATCH 21/34] sunxi: update cpu_sunxi_ncat2.h Andre Przywara
2025-03-23 11:35 ` [PATCH 22/34] sunxi: Kconfig: consolidate SYS_CLK_FREQ selection Andre Przywara
2025-03-23 12:21 ` Jernej Škrabec
2025-03-23 11:35 ` [PATCH 23/34] spl: reorder SPL_MAX_SIZE defaults for sunxi Andre Przywara
2025-03-23 12:22 ` Jernej Škrabec
2025-03-23 11:35 ` [PATCH 24/34] sunxi: armv8: fel: move fel_stash variable to the front Andre Przywara
2025-03-23 12:23 ` Jernej Škrabec
2025-03-23 11:35 ` [PATCH 25/34] sunxi: arm64: boot0.h: move fel_stash_addr " Andre Przywara
2025-03-23 12:23 ` Jernej Škrabec
2025-03-23 11:35 ` [PATCH 26/34] sunxi: update rmr_switch.S source code Andre Przywara
2025-03-23 12:24 ` Jernej Škrabec
2025-03-23 11:35 ` [PATCH 27/34] sunxi: armv8: FEL: save and restore GICv3 registers Andre Przywara
2025-03-23 12:25 ` Jernej Škrabec
2025-03-23 11:35 ` [PATCH 28/34] sunxi: armv8: FEL: save and restore SP_IRQ Andre Przywara
2025-03-23 12:26 ` Jernej Škrabec
2025-03-23 23:52 ` Andre Przywara
2025-03-23 11:35 ` [PATCH 29/34] sunxi: sun50i_h6: add A523 SPL clock setup code Andre Przywara
2025-03-23 12:36 ` Jernej Škrabec
2025-03-23 11:35 ` [PATCH 30/34] sunxi: A523: add DRAM initialisation routine Andre Przywara
2025-03-23 13:15 ` Jernej Škrabec
2025-04-05 22:01 ` Yixun Lan
2025-04-07 9:26 ` Andre Przywara
2025-03-23 11:35 ` Andre Przywara [this message]
2025-03-23 11:35 ` [PATCH 32/34] sunxi: add basic A523 support Andre Przywara
2025-03-23 11:35 ` [PATCH 33/34] sunxi: A523: add DT files from Linux v3 branch Andre Przywara
2025-04-09 14:28 ` Yixun Lan
2025-03-23 11:35 ` [PATCH 34/34] sunxi: A523: add defconfigs for three boards Andre Przywara
2025-04-05 2:44 ` [PATCH 00/34] sunxi: clock refactoring and Allwinner A523 support Yixun Lan
2025-04-05 12:32 ` Andre Przywara
2025-04-05 13:04 ` Yixun Lan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250323113544.7933-32-andre.przywara@arm.com \
--to=andre.przywara@arm.com \
--cc=iuncuim@gmail.com \
--cc=jernej.skrabec@gmail.com \
--cc=linux-sunxi@lists.linux.dev \
--cc=sjg@chromium.org \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox