From: Richard Genoud <richard.genoud@bootlin.com>
To: Miquel Raynal <miquel.raynal@bootlin.com>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Samuel Holland <samuel@sholland.org>
Cc: "Uwe Kleine-König" <u.kleine-koenig@baylibre.com>,
"Wentao Liang" <vulab@iscas.ac.cn>,
"Johan Hovold" <johan@kernel.org>,
"Maxime Ripard" <mripard@kernel.org>,
"Thomas Petazzoni" <thomas.petazzoni@bootlin.com>,
linux-mtd@lists.infradead.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org,
"Richard Genoud" <richard.genoud@bootlin.com>
Subject: [PATCH v4 05/16] mtd: rawnand: sunxi: introduce reg_ecc_err_cnt in sunxi_nfc_caps
Date: Tue, 28 Oct 2025 08:34:58 +0100 [thread overview]
Message-ID: <20251028073534.526992-6-richard.genoud@bootlin.com> (raw)
In-Reply-To: <20251028073534.526992-1-richard.genoud@bootlin.com>
The H6/H616 ECC_ERR_CNT register is not at the same offset as the
A10/A23 one, so move its offset into sunxi_nfc_caps
No functional change.
Signed-off-by: Richard Genoud <richard.genoud@bootlin.com>
---
drivers/mtd/nand/raw/sunxi_nand.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
diff --git a/drivers/mtd/nand/raw/sunxi_nand.c b/drivers/mtd/nand/raw/sunxi_nand.c
index 89115a8f0718..d877c20c203d 100644
--- a/drivers/mtd/nand/raw/sunxi_nand.c
+++ b/drivers/mtd/nand/raw/sunxi_nand.c
@@ -46,7 +46,8 @@
#define NFC_REG_ECC_CTL 0x0034
#define NFC_REG_ECC_ST 0x0038
#define NFC_REG_DEBUG 0x003C
-#define NFC_REG_ECC_ERR_CNT(x) ((0x0040 + (x)) & ~0x3)
+#define NFC_REG_A10_ECC_ERR_CNT 0x0040
+#define NFC_REG_ECC_ERR_CNT(nfc, x) ((nfc->caps->reg_ecc_err_cnt + (x)) & ~0x3)
#define NFC_REG_USER_DATA(x) (0x0050 + ((x) * 4))
#define NFC_REG_SPARE_AREA 0x00A0
#define NFC_REG_PAT_ID 0x00A4
@@ -223,6 +224,7 @@ static inline struct sunxi_nand_chip *to_sunxi_nand(struct nand_chip *nand)
* @has_mdma: Use mbus dma mode, otherwise general dma
* through MBUS on A23/A33 needs extra configuration.
* @reg_io_data: I/O data register
+ * @reg_ecc_err_cnt: ECC error counter register
* @dma_maxburst: DMA maxburst
* @ecc_strengths: Available ECC strengths array
* @nstrengths: Size of @ecc_strengths
@@ -230,6 +232,7 @@ static inline struct sunxi_nand_chip *to_sunxi_nand(struct nand_chip *nand)
struct sunxi_nfc_caps {
bool has_mdma;
unsigned int reg_io_data;
+ unsigned int reg_ecc_err_cnt;
unsigned int dma_maxburst;
const u8 *ecc_strengths;
unsigned int nstrengths;
@@ -801,7 +804,7 @@ static int sunxi_nfc_hw_ecc_correct(struct nand_chip *nand, u8 *data, u8 *oob,
return 0;
}
- tmp = readl(nfc->regs + NFC_REG_ECC_ERR_CNT(step));
+ tmp = readl(nfc->regs + NFC_REG_ECC_ERR_CNT(nfc, step));
return NFC_ECC_ERR_CNT(step, tmp);
}
@@ -2188,6 +2191,7 @@ static const u8 sunxi_ecc_strengths_a10[] = {
static const struct sunxi_nfc_caps sunxi_nfc_a10_caps = {
.reg_io_data = NFC_REG_A10_IO_DATA,
+ .reg_ecc_err_cnt = NFC_REG_A10_ECC_ERR_CNT,
.dma_maxburst = 4,
.ecc_strengths = sunxi_ecc_strengths_a10,
.nstrengths = ARRAY_SIZE(sunxi_ecc_strengths_a10),
@@ -2196,6 +2200,7 @@ static const struct sunxi_nfc_caps sunxi_nfc_a10_caps = {
static const struct sunxi_nfc_caps sunxi_nfc_a23_caps = {
.has_mdma = true,
.reg_io_data = NFC_REG_A23_IO_DATA,
+ .reg_ecc_err_cnt = NFC_REG_A10_ECC_ERR_CNT,
.dma_maxburst = 8,
.ecc_strengths = sunxi_ecc_strengths_a10,
.nstrengths = ARRAY_SIZE(sunxi_ecc_strengths_a10),
--
2.47.3
next prev parent reply other threads:[~2025-10-28 7:36 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-28 7:34 [PATCH v4 00/16] Introduce Allwinner H6/H616 NAND controller support Richard Genoud
2025-10-28 7:34 ` [PATCH v4 01/16] dt-bindings: mtd: sunxi: Add H616 compatible Richard Genoud
2025-10-28 7:34 ` [PATCH v4 02/16] mtd: rawnand: sunxi: Remove superfluous register readings Richard Genoud
2025-10-28 7:34 ` [PATCH v4 03/16] mtd: rawnand: sunxi: Replace hard coded value by a define Richard Genoud
2025-10-28 15:34 ` Jernej Škrabec
2025-10-28 7:34 ` [PATCH v4 04/16] mtd: rawnand: sunxi: move ECC strenghts in sunxi_nfc_caps Richard Genoud
2025-10-28 7:34 ` Richard Genoud [this message]
2025-10-28 15:36 ` [PATCH v4 05/16] mtd: rawnand: sunxi: introduce reg_ecc_err_cnt " Jernej Škrabec
2025-10-28 7:34 ` [PATCH v4 06/16] mtd: rawnand: sunxi: introduce reg_user_data " Richard Genoud
2025-10-28 15:37 ` Jernej Škrabec
2025-10-28 7:35 ` [PATCH v4 07/16] mtd: rawnand: sunxi: rework pattern found registers Richard Genoud
2025-10-28 15:41 ` Jernej Škrabec
2025-10-28 16:20 ` Miquel Raynal
2025-10-28 7:35 ` [PATCH v4 08/16] mtd: rawnand: sunxi: add has_ecc_block_512 capability Richard Genoud
2025-10-28 15:43 ` Jernej Škrabec
2025-10-28 7:35 ` [PATCH v4 09/16] mtd: rawnand: sunxi: introduce ecc_mode_mask in sunxi_nfc_caps Richard Genoud
2025-10-28 7:35 ` [PATCH v4 10/16] mtd: rawnand: sunxi: introduce random en/dir " Richard Genoud
2025-10-28 7:35 ` [PATCH v4 11/16] mtd: rawnand: sunxi: introduce reg_pat_id " Richard Genoud
2025-10-28 15:45 ` Jernej Škrabec
2025-10-28 7:35 ` [PATCH v4 12/16] mtd: rawnand: sunxi: introduce reg_spare_area " Richard Genoud
2025-10-28 15:45 ` Jernej Škrabec
2025-10-28 7:35 ` [PATCH v4 13/16] mtd: rawnand: sunxi: introduce ecc_err_mask " Richard Genoud
2025-10-28 7:35 ` [PATCH v4 14/16] mtd: rawnand: sunxi: introduce sram_size " Richard Genoud
2025-10-28 15:46 ` Jernej Škrabec
2025-10-28 7:35 ` [PATCH v4 15/16] mtd: rawnand: sunxi: Add support for H616 nand controller Richard Genoud
2025-10-28 7:35 ` [PATCH v4 16/16] arm64: dts: allwinner: h616: add NAND controller Richard Genoud
2025-10-28 16:23 ` [PATCH v4 00/16] Introduce Allwinner H6/H616 NAND controller support Miquel Raynal
2025-10-28 17:05 ` (subset) " Chen-Yu Tsai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20251028073534.526992-6-richard.genoud@bootlin.com \
--to=richard.genoud@bootlin.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jernej.skrabec@gmail.com \
--cc=johan@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=miquel.raynal@bootlin.com \
--cc=mripard@kernel.org \
--cc=richard@nod.at \
--cc=robh@kernel.org \
--cc=samuel@sholland.org \
--cc=thomas.petazzoni@bootlin.com \
--cc=u.kleine-koenig@baylibre.com \
--cc=vigneshr@ti.com \
--cc=vulab@iscas.ac.cn \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox