Re: [PATCH] sunxi: H6: Enable Ethernet on Orange Pi One Plus

Re: [PATCH] sunxi: H6: Enable Ethernet on Orange Pi One Plus

[Anne Macedo]

On 11.07.2023 02:39, Anne Macedo wrote:
> Enable Ethernet on Orange Pi One Plus by using the correct phy for
> Realtek RTL8211E instead of the Generic One. Also use CONFIG_MACPWR to
> turn on ethernet on startup.
> 
> After this patch is applied, a few issues can be seen:
> 
> - there's still a PHY reset timed out error that doesn't seem to cause
>   any impacts to the overall connection
> 
> - sometimes the emac driver times out after reset (yellow LED turns on
>   and never blinks)
> 
> For future patches: for now, CONFIG_MACPWR is the only way to enable
> Ethernet on boot. There's already code on the dts for using the 
> 3v3-gmac
> regulator. However, it is not probed on boot, so it only starts after a
> "regulator status" command is issued.
> 
> More details about the troubleshooting on [1].
> 
> [1]
> https://lore.kernel.org/u-boot/4wsvwgy56e2xfgtvioru2tf2ofkqprlts36qggivxogww6pn5j@4jk63zxhzhag/
> 
> Signed-off-by: Anne Macedo <retpolanne@posteo.net>
> ---
>  arch/arm/dts/sun50i-h6-orangepi-one-plus.dts | 2 +-
>  configs/orangepi_one_plus_defconfig          | 4 ++++
>  2 files changed, 5 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> index 29a081e72a..6427c58f8a 100644
> --- a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> +++ b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> @@ -37,7 +37,7 @@
> 
>  &mdio {
>  	ext_rgmii_phy: ethernet-phy@1 {
> -		compatible = "ethernet-phy-ieee802.3-c22";
> +		compatible = "ethernet-phy-id001c.c915", 
> "ethernet-phy-ieee802.3-c22" ;
>  		reg = <1>;
>  	};
>  };
> diff --git a/configs/orangepi_one_plus_defconfig
> b/configs/orangepi_one_plus_defconfig
> index aa5f540eb1..a1835492db 100644
> --- a/configs/orangepi_one_plus_defconfig
> +++ b/configs/orangepi_one_plus_defconfig
> @@ -8,3 +8,7 @@ CONFIG_SUNXI_DRAM_H6_LPDDR3=y
>  # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
>  CONFIG_USB_EHCI_HCD=y
>  CONFIG_USB_OHCI_HCD=y
> +CONFIG_SUN8I_EMAC=y
> +CONFIG_PHY_REALTEK=y
> +CONFIG_PHY_ETHERNET_ID=y
> +CONFIG_MACPWR="PD6"

Adding linux-sunxi to the thread (I unfortunately forgot this list)

Re: [PATCH] sunxi: H6: Enable Ethernet on Orange Pi One Plus

[Andre Przywara]

On Tue, 11 Jul 2023 19:40:21 +0000
Anne Macedo <retpolanne@posteo.net> wrote:

Hi Anne,

thanks for reaching out to the list! But please try to avoid
pushing any patches downstream (Yocto) before they are accepted
or at least discussed upstream, see below.

> On 11.07.2023 02:39, Anne Macedo wrote:
> > Enable Ethernet on Orange Pi One Plus by using the correct phy for
> > Realtek RTL8211E instead of the Generic One. Also use CONFIG_MACPWR to
> > turn on ethernet on startup.
> > 
> > After this patch is applied, a few issues can be seen:
> > 
> > - there's still a PHY reset timed out error that doesn't seem to cause
> >   any impacts to the overall connection
> > 
> > - sometimes the emac driver times out after reset (yellow LED turns on
> >   and never blinks)
> > 
> > For future patches: for now, CONFIG_MACPWR is the only way to enable
> > Ethernet on boot. There's already code on the dts for using the 
> > 3v3-gmac
> > regulator. However, it is not probed on boot, so it only starts after a
> > "regulator status" command is issued.

MACPWR is going to go away (probably in the next two weeks), so please
have a look at this patch and see if that works for you:
https://github.com/apritzel/u-boot/commit/be1fdb42968

> > 
> > More details about the troubleshooting on [1].
> > 
> > [1]
> > https://lore.kernel.org/u-boot/4wsvwgy56e2xfgtvioru2tf2ofkqprlts36qggivxogww6pn5j@4jk63zxhzhag/
> > 
> > Signed-off-by: Anne Macedo <retpolanne@posteo.net>
> > ---
> >  arch/arm/dts/sun50i-h6-orangepi-one-plus.dts | 2 +-
> >  configs/orangepi_one_plus_defconfig          | 4 ++++
> >  2 files changed, 5 insertions(+), 1 deletion(-)
> > 
> > diff --git a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > index 29a081e72a..6427c58f8a 100644
> > --- a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > +++ b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > @@ -37,7 +37,7 @@
> > 
> >  &mdio {
> >  	ext_rgmii_phy: ethernet-phy@1 {
> > -		compatible = "ethernet-phy-ieee802.3-c22";
> > +		compatible = "ethernet-phy-id001c.c915", 
> > "ethernet-phy-ieee802.3-c22" ;

So this is really odd, why would you need that? 001c.c915 is the ID for
the normal standard Realtek 8211E PHY, which would be auto-detected via
MDIO. You just need to define CONFIG_PHY_REALTEK to include support.
Forcing this in the DT is not necessary and smells wrong.

But I suppose you needed that to get it to work, so could this be a
timing issue? Maybe the PHY doesn't come up quick enough after just
pulling PD6 high, so the auto-detection wouldn't work? The DT has a
"startup-delay-us = <100000>;" property, which MACPWR doesn't know
about and wouldn't observe.
So could you check whether just applying the "Remove MACPWR" patch, plus
adding "CONFIG_SUN8I_EMAC=y" and "CONFIG_PHY_REALTEK=y" to defconfig
fixes the issue? You may need to enable CONFIG_DM_REGULATOR_FIXED=y as
well, although this would become standard for all sunxi boards soon.

And you must NOT use SUNXI_SETUP_REGULATORS=0 in TF-A, as you need
ALDO2 to be set up by TF-A. We introduced this build option to
accommodate the OrangePi 3 board, which requires a specifically timed
regulator setup, which both TF-A and U-Boot would not observe. To not
crash the PHY with any incorrect regulator setup, we use this option to
make at least Linux work. The side effect is that some peripherals
(HDMI, Ethernet) will not work in U-Boot.
Also please note that a reset from Linux might not affect the PMIC, so
there might be different behaviour between and cold and warm boot.

Cheers,
Andre

> >  		reg = <1>;
> >  	};
> >  };
> > diff --git a/configs/orangepi_one_plus_defconfig
> > b/configs/orangepi_one_plus_defconfig
> > index aa5f540eb1..a1835492db 100644
> > --- a/configs/orangepi_one_plus_defconfig
> > +++ b/configs/orangepi_one_plus_defconfig
> > @@ -8,3 +8,7 @@ CONFIG_SUNXI_DRAM_H6_LPDDR3=y
> >  # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> >  CONFIG_USB_EHCI_HCD=y
> >  CONFIG_USB_OHCI_HCD=y
> > +CONFIG_SUN8I_EMAC=y
> > +CONFIG_PHY_REALTEK=y
> > +CONFIG_PHY_ETHERNET_ID=y
> > +CONFIG_MACPWR="PD6"  
> 
> Adding linux-sunxi to the thread (I unfortunately forgot this list)
> 

Re: [PATCH] sunxi: H6: Enable Ethernet on Orange Pi One Plus

[Corentin Labbe]

Le Sun, Jul 16, 2023 at 01:35:02AM +0100, Andre Przywara a écrit :
> On Tue, 11 Jul 2023 19:40:21 +0000
> Anne Macedo <retpolanne@posteo.net> wrote:
> 
> Hi Anne,
> 
> thanks for reaching out to the list! But please try to avoid
> pushing any patches downstream (Yocto) before they are accepted
> or at least discussed upstream, see below.
> 
> > On 11.07.2023 02:39, Anne Macedo wrote:
> > > Enable Ethernet on Orange Pi One Plus by using the correct phy for
> > > Realtek RTL8211E instead of the Generic One. Also use CONFIG_MACPWR to
> > > turn on ethernet on startup.
> > > 
> > > After this patch is applied, a few issues can be seen:
> > > 
> > > - there's still a PHY reset timed out error that doesn't seem to cause
> > >   any impacts to the overall connection
> > > 
> > > - sometimes the emac driver times out after reset (yellow LED turns on
> > >   and never blinks)
> > > 
> > > For future patches: for now, CONFIG_MACPWR is the only way to enable
> > > Ethernet on boot. There's already code on the dts for using the 
> > > 3v3-gmac
> > > regulator. However, it is not probed on boot, so it only starts after a
> > > "regulator status" command is issued.
> 
> MACPWR is going to go away (probably in the next two weeks), so please
> have a look at this patch and see if that works for you:
> https://github.com/apritzel/u-boot/commit/be1fdb42968
> 
> > > 
> > > More details about the troubleshooting on [1].
> > > 
> > > [1]
> > > https://lore.kernel.org/u-boot/4wsvwgy56e2xfgtvioru2tf2ofkqprlts36qggivxogww6pn5j@4jk63zxhzhag/
> > > 
> > > Signed-off-by: Anne Macedo <retpolanne@posteo.net>
> > > ---
> > >  arch/arm/dts/sun50i-h6-orangepi-one-plus.dts | 2 +-
> > >  configs/orangepi_one_plus_defconfig          | 4 ++++
> > >  2 files changed, 5 insertions(+), 1 deletion(-)
> > > 
> > > diff --git a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > index 29a081e72a..6427c58f8a 100644
> > > --- a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > +++ b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > @@ -37,7 +37,7 @@
> > > 
> > >  &mdio {
> > >  	ext_rgmii_phy: ethernet-phy@1 {
> > > -		compatible = "ethernet-phy-ieee802.3-c22";
> > > +		compatible = "ethernet-phy-id001c.c915", 
> > > "ethernet-phy-ieee802.3-c22" ;
> 
> So this is really odd, why would you need that? 001c.c915 is the ID for
> the normal standard Realtek 8211E PHY, which would be auto-detected via
> MDIO. You just need to define CONFIG_PHY_REALTEK to include support.
> Forcing this in the DT is not necessary and smells wrong.
> 
> But I suppose you needed that to get it to work, so could this be a
> timing issue? Maybe the PHY doesn't come up quick enough after just
> pulling PD6 high, so the auto-detection wouldn't work? The DT has a
> "startup-delay-us = <100000>;" property, which MACPWR doesn't know
> about and wouldn't observe.
> So could you check whether just applying the "Remove MACPWR" patch, plus
> adding "CONFIG_SUN8I_EMAC=y" and "CONFIG_PHY_REALTEK=y" to defconfig
> fixes the issue? You may need to enable CONFIG_DM_REGULATOR_FIXED=y as
> well, although this would become standard for all sunxi boards soon.
> 
> And you must NOT use SUNXI_SETUP_REGULATORS=0 in TF-A, as you need
> ALDO2 to be set up by TF-A. We introduced this build option to
> accommodate the OrangePi 3 board, which requires a specifically timed
> regulator setup, which both TF-A and U-Boot would not observe. To not
> crash the PHY with any incorrect regulator setup, we use this option to
> make at least Linux work. The side effect is that some peripherals
> (HDMI, Ethernet) will not work in U-Boot.
> Also please note that a reset from Linux might not affect the PMIC, so
> there might be different behaviour between and cold and warm boot.
> 
> Cheers,
> Andre
> 
> > >  		reg = <1>;
> > >  	};
> > >  };
> > > diff --git a/configs/orangepi_one_plus_defconfig
> > > b/configs/orangepi_one_plus_defconfig
> > > index aa5f540eb1..a1835492db 100644
> > > --- a/configs/orangepi_one_plus_defconfig
> > > +++ b/configs/orangepi_one_plus_defconfig
> > > @@ -8,3 +8,7 @@ CONFIG_SUNXI_DRAM_H6_LPDDR3=y
> > >  # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > >  CONFIG_USB_EHCI_HCD=y
> > >  CONFIG_USB_OHCI_HCD=y
> > > +CONFIG_SUN8I_EMAC=y
> > > +CONFIG_PHY_REALTEK=y
> > > +CONFIG_PHY_ETHERNET_ID=y
> > > +CONFIG_MACPWR="PD6"  
> > 
> > Adding linux-sunxi to the thread (I unfortunately forgot this list)
> > 
> 
> 

Hello

Note that there is already a try to fix this in upstream linux:
The v4 can be found at https://lore.kernel.org/linux-arm-kernel/Y3RDumClNkEW6L4F@lunn.ch/T/

And that I will send soon my last version https://github.com/montjoie/linux/tree/opi3-v5

Regards

Re: [PATCH] sunxi: H6: Enable Ethernet on Orange Pi One Plus

[Anne Macedo]

On Sun, Jul 16, 2023 at 08:14:50AM +0200, Corentin Labbe wrote:
> Le Sun, Jul 16, 2023 at 01:35:02AM +0100, Andre Przywara a écrit :
> > On Tue, 11 Jul 2023 19:40:21 +0000
> > Anne Macedo <retpolanne@posteo.net> wrote:
> > 
> > Hi Anne,
> > 
> > thanks for reaching out to the list! But please try to avoid
> > pushing any patches downstream (Yocto) before they are accepted
> > or at least discussed upstream, see below.
> > 
> > > On 11.07.2023 02:39, Anne Macedo wrote:
> > > > Enable Ethernet on Orange Pi One Plus by using the correct phy for
> > > > Realtek RTL8211E instead of the Generic One. Also use CONFIG_MACPWR to
> > > > turn on ethernet on startup.
> > > > 
> > > > After this patch is applied, a few issues can be seen:
> > > > 
> > > > - there's still a PHY reset timed out error that doesn't seem to cause
> > > >   any impacts to the overall connection
> > > > 
> > > > - sometimes the emac driver times out after reset (yellow LED turns on
> > > >   and never blinks)
> > > > 
> > > > For future patches: for now, CONFIG_MACPWR is the only way to enable
> > > > Ethernet on boot. There's already code on the dts for using the 
> > > > 3v3-gmac
> > > > regulator. However, it is not probed on boot, so it only starts after a
> > > > "regulator status" command is issued.
> > 
> > MACPWR is going to go away (probably in the next two weeks), so please
> > have a look at this patch and see if that works for you:
> > https://github.com/apritzel/u-boot/commit/be1fdb42968
> > 
> > > > 
> > > > More details about the troubleshooting on [1].
> > > > 
> > > > [1]
> > > > https://lore.kernel.org/u-boot/4wsvwgy56e2xfgtvioru2tf2ofkqprlts36qggivxogww6pn5j@4jk63zxhzhag/
> > > > 
> > > > Signed-off-by: Anne Macedo <retpolanne@posteo.net>
> > > > ---
> > > >  arch/arm/dts/sun50i-h6-orangepi-one-plus.dts | 2 +-
> > > >  configs/orangepi_one_plus_defconfig          | 4 ++++
> > > >  2 files changed, 5 insertions(+), 1 deletion(-)
> > > > 
> > > > diff --git a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > > b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > > index 29a081e72a..6427c58f8a 100644
> > > > --- a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > > +++ b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > > @@ -37,7 +37,7 @@
> > > > 
> > > >  &mdio {
> > > >  	ext_rgmii_phy: ethernet-phy@1 {
> > > > -		compatible = "ethernet-phy-ieee802.3-c22";
> > > > +		compatible = "ethernet-phy-id001c.c915", 
> > > > "ethernet-phy-ieee802.3-c22" ;
> > 
> > So this is really odd, why would you need that? 001c.c915 is the ID for
> > the normal standard Realtek 8211E PHY, which would be auto-detected via
> > MDIO. You just need to define CONFIG_PHY_REALTEK to include support.
> > Forcing this in the DT is not necessary and smells wrong.
> > 
> > But I suppose you needed that to get it to work, so could this be a
> > timing issue? Maybe the PHY doesn't come up quick enough after just
> > pulling PD6 high, so the auto-detection wouldn't work? The DT has a
> > "startup-delay-us = <100000>;" property, which MACPWR doesn't know
> > about and wouldn't observe.
> > So could you check whether just applying the "Remove MACPWR" patch, plus
> > adding "CONFIG_SUN8I_EMAC=y" and "CONFIG_PHY_REALTEK=y" to defconfig
> > fixes the issue? You may need to enable CONFIG_DM_REGULATOR_FIXED=y as
> > well, although this would become standard for all sunxi boards soon.
> > 
> > And you must NOT use SUNXI_SETUP_REGULATORS=0 in TF-A, as you need
> > ALDO2 to be set up by TF-A. We introduced this build option to
> > accommodate the OrangePi 3 board, which requires a specifically timed
> > regulator setup, which both TF-A and U-Boot would not observe. To not
> > crash the PHY with any incorrect regulator setup, we use this option to
> > make at least Linux work. The side effect is that some peripherals
> > (HDMI, Ethernet) will not work in U-Boot.
> > Also please note that a reset from Linux might not affect the PMIC, so
> > there might be different behaviour between and cold and warm boot.
> > 
> > Cheers,
> > Andre
> > 
> > > >  		reg = <1>;
> > > >  	};
> > > >  };
> > > > diff --git a/configs/orangepi_one_plus_defconfig
> > > > b/configs/orangepi_one_plus_defconfig
> > > > index aa5f540eb1..a1835492db 100644
> > > > --- a/configs/orangepi_one_plus_defconfig
> > > > +++ b/configs/orangepi_one_plus_defconfig
> > > > @@ -8,3 +8,7 @@ CONFIG_SUNXI_DRAM_H6_LPDDR3=y
> > > >  # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > > >  CONFIG_USB_EHCI_HCD=y
> > > >  CONFIG_USB_OHCI_HCD=y
> > > > +CONFIG_SUN8I_EMAC=y
> > > > +CONFIG_PHY_REALTEK=y
> > > > +CONFIG_PHY_ETHERNET_ID=y
> > > > +CONFIG_MACPWR="PD6"  
> > > 
> > > Adding linux-sunxi to the thread (I unfortunately forgot this list)
> > > 
> > 
> > 
> 
> Hello
> 
> Note that there is already a try to fix this in upstream linux:
> The v4 can be found at https://lore.kernel.org/linux-arm-kernel/Y3RDumClNkEW6L4F@lunn.ch/T/
> 
> And that I will send soon my last version https://github.com/montjoie/linux/tree/opi3-v5
Awesome! Once this gets merged, I can try to implement this on the
orange pi one plus (I believe your patch, although generic and supported
by a few boards, doesn't support the Orange Pi One Plus, right?).

Thanks for letting me know! 
> 
> Regards

Re: [PATCH] sunxi: H6: Enable Ethernet on Orange Pi One Plus

[Anne Macedo]

On Sun, Jul 16, 2023 at 01:35:02AM +0100, Andre Przywara wrote:
> On Tue, 11 Jul 2023 19:40:21 +0000
> Anne Macedo <retpolanne@posteo.net> wrote:
> 
> Hi Anne,
> 
> thanks for reaching out to the list! But please try to avoid
> pushing any patches downstream (Yocto) before they are accepted
> or at least discussed upstream, see below.

Hey Andre! Apologies for the mess! I'll let folks from meta-sunxi know
and remove the patch for now from their layer.
> 
> > On 11.07.2023 02:39, Anne Macedo wrote:
> > > Enable Ethernet on Orange Pi One Plus by using the correct phy for
> > > Realtek RTL8211E instead of the Generic One. Also use CONFIG_MACPWR to
> > > turn on ethernet on startup.
> > > 
> > > After this patch is applied, a few issues can be seen:
> > > 
> > > - there's still a PHY reset timed out error that doesn't seem to cause
> > >   any impacts to the overall connection
> > > 
> > > - sometimes the emac driver times out after reset (yellow LED turns on
> > >   and never blinks)
> > > 
> > > For future patches: for now, CONFIG_MACPWR is the only way to enable
> > > Ethernet on boot. There's already code on the dts for using the 
> > > 3v3-gmac
> > > regulator. However, it is not probed on boot, so it only starts after a
> > > "regulator status" command is issued.
> 
> MACPWR is going to go away (probably in the next two weeks), so please
> have a look at this patch and see if that works for you:
> https://github.com/apritzel/u-boot/commit/be1fdb42968

Thanks! Will take a look.
> 
> > > 
> > > More details about the troubleshooting on [1].
> > > 
> > > [1]
> > > https://lore.kernel.org/u-boot/4wsvwgy56e2xfgtvioru2tf2ofkqprlts36qggivxogww6pn5j@4jk63zxhzhag/
> > > 
> > > Signed-off-by: Anne Macedo <retpolanne@posteo.net>
> > > ---
> > >  arch/arm/dts/sun50i-h6-orangepi-one-plus.dts | 2 +-
> > >  configs/orangepi_one_plus_defconfig          | 4 ++++
> > >  2 files changed, 5 insertions(+), 1 deletion(-)
> > > 
> > > diff --git a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > index 29a081e72a..6427c58f8a 100644
> > > --- a/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > +++ b/arch/arm/dts/sun50i-h6-orangepi-one-plus.dts
> > > @@ -37,7 +37,7 @@
> > > 
> > >  &mdio {
> > >  	ext_rgmii_phy: ethernet-phy@1 {
> > > -		compatible = "ethernet-phy-ieee802.3-c22";
> > > +		compatible = "ethernet-phy-id001c.c915", 
> > > "ethernet-phy-ieee802.3-c22" ;
> 
> So this is really odd, why would you need that? 001c.c915 is the ID for
> the normal standard Realtek 8211E PHY, which would be auto-detected via
> MDIO. You just need to define CONFIG_PHY_REALTEK to include support.
> Forcing this in the DT is not necessary and smells wrong.

Interesting, I really tried using CONFIG_PHY_REALTEK but it never
reached the code that detected the PHY, making it only detect the
Generic PHY.
> 
> But I suppose you needed that to get it to work, so could this be a
> timing issue? Maybe the PHY doesn't come up quick enough after just
> pulling PD6 high, so the auto-detection wouldn't work? The DT has a
> "startup-delay-us = <100000>;" property, which MACPWR doesn't know
> about and wouldn't observe.

That sounds like it! When I was troubleshooting, I noticed that PHY
detection (for the Generic PHY) was really intermittent. 

> So could you check whether just applying the "Remove MACPWR" patch, plus
> adding "CONFIG_SUN8I_EMAC=y" and "CONFIG_PHY_REALTEK=y" to defconfig
> fixes the issue? You may need to enable CONFIG_DM_REGULATOR_FIXED=y as
> well, although this would become standard for all sunxi boards soon.

Will take a look! Unfortunately I lost my PC :( so I will probably take
a little why to resume my troubleshooting.
> 
> And you must NOT use SUNXI_SETUP_REGULATORS=0 in TF-A, as you need
> ALDO2 to be set up by TF-A. We introduced this build option to
> accommodate the OrangePi 3 board, which requires a specifically timed
> regulator setup, which both TF-A and U-Boot would not observe. To not
> crash the PHY with any incorrect regulator setup, we use this option to
> make at least Linux work. The side effect is that some peripherals
> (HDMI, Ethernet) will not work in U-Boot.
> Also please note that a reset from Linux might not affect the PMIC, so
> there might be different behaviour between and cold and warm boot.
> 
> Cheers,
> Andre
> 
> > >  		reg = <1>;
> > >  	};
> > >  };
> > > diff --git a/configs/orangepi_one_plus_defconfig
> > > b/configs/orangepi_one_plus_defconfig
> > > index aa5f540eb1..a1835492db 100644
> > > --- a/configs/orangepi_one_plus_defconfig
> > > +++ b/configs/orangepi_one_plus_defconfig
> > > @@ -8,3 +8,7 @@ CONFIG_SUNXI_DRAM_H6_LPDDR3=y
> > >  # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > >  CONFIG_USB_EHCI_HCD=y
> > >  CONFIG_USB_OHCI_HCD=y
> > > +CONFIG_SUN8I_EMAC=y
> > > +CONFIG_PHY_REALTEK=y
> > > +CONFIG_PHY_ETHERNET_ID=y
> > > +CONFIG_MACPWR="PD6"  
> > 
> > Adding linux-sunxi to the thread (I unfortunately forgot this list)
> > 
>