[PATCH v4 0/2 RESEND] gpu/drm: tegra: add DSI support for Tegra20/Tegra30

[PATCH v4 0/2 RESEND] gpu/drm: tegra: add DSI support for Tegra20/Tegra30

[Svyatoslav Ryhel]

Tegra20/Tegra30 DSI is quite similar to Tegra114+ apart MIPI calibration
logic and clocks. With a few minor tweaks, existing tegra DSI driver
should work on Tegra20/Tegra30 devices just fine. Tested on
Motorola Atrix 4G (T20) and ASUS VivoTab RT TF600T (T30).

This patchset depends on Tegra20/Tegra30 CSI bringup since both share
MIPI calibration logic. Ideally these patches should be picked after
CSI bringup but they will not break anything even if picked before
CSI patches.

---
Changes in v2:
- removed all MIPI calibration, it is handled within CSI bringup
- added per-soc structures into of_match
- added fix for hang caused by register access with uninited hw

Changes in v3:
- switched from version DSI to boolean flags
- added comment regarding Tegra30 clock configuration
- commits were picked:
  "clk: tegra20: reparent dsi clock to pll_d_out0"
  "ARM: tegra: adjust DSI nodes for Tegra20/Tegra30"
- commit adapted to recent DSI changes:
  "gpu/drm: tegra: dsi: move prepare function at the top of encoder
    enable" > "gpu/drm: tegra: dsi: re-add clear enable register if
    DSI was powered by bootloader"

Changes in v4:
- switched to device_get_match_data and added check
- added comment regarding Tegra124+ quirk
- adjusted commit titles and message formatting
---

Svyatoslav Ryhel (2):
  drm/tegra: dsi: add support for Tegra20/Tegra30
  drm/tegra: dsi: re-add clear enable register if DSI was powered by
    bootloader

 drivers/gpu/drm/tegra/drm.c |   2 +
 drivers/gpu/drm/tegra/dsi.c | 126 +++++++++++++++++++++++++++---------
 drivers/gpu/drm/tegra/dsi.h |  10 +++
 3 files changed, 107 insertions(+), 31 deletions(-)

-- 
2.51.0

[PATCH v4 1/2 RESEND] drm/tegra: dsi: add support for Tegra20/Tegra30

[Svyatoslav Ryhel]

Tegra20 and Tegra30 are fully compatible with existing Tegra DSI driver
apart from clock configuration and pad calibration which are addressed by
this patch.

Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
---
 drivers/gpu/drm/tegra/drm.c |   2 +
 drivers/gpu/drm/tegra/dsi.c | 117 ++++++++++++++++++++++++++----------
 drivers/gpu/drm/tegra/dsi.h |  10 +++
 3 files changed, 98 insertions(+), 31 deletions(-)

diff --git a/drivers/gpu/drm/tegra/drm.c b/drivers/gpu/drm/tegra/drm.c
index 1dcef4e7d104..b73d65cd0ac6 100644
--- a/drivers/gpu/drm/tegra/drm.c
+++ b/drivers/gpu/drm/tegra/drm.c
@@ -1358,10 +1358,12 @@ static SIMPLE_DEV_PM_OPS(host1x_drm_pm_ops, host1x_drm_suspend,
 
 static const struct of_device_id host1x_drm_subdevs[] = {
 	{ .compatible = "nvidia,tegra20-dc", },
+	{ .compatible = "nvidia,tegra20-dsi", },
 	{ .compatible = "nvidia,tegra20-hdmi", },
 	{ .compatible = "nvidia,tegra20-gr2d", },
 	{ .compatible = "nvidia,tegra20-gr3d", },
 	{ .compatible = "nvidia,tegra30-dc", },
+	{ .compatible = "nvidia,tegra30-dsi", },
 	{ .compatible = "nvidia,tegra30-hdmi", },
 	{ .compatible = "nvidia,tegra30-gr2d", },
 	{ .compatible = "nvidia,tegra30-gr3d", },
diff --git a/drivers/gpu/drm/tegra/dsi.c b/drivers/gpu/drm/tegra/dsi.c
index 7f25c50621c9..fbab10bc5c41 100644
--- a/drivers/gpu/drm/tegra/dsi.c
+++ b/drivers/gpu/drm/tegra/dsi.c
@@ -54,6 +54,11 @@ to_dsi_state(struct drm_connector_state *state)
 	return container_of(state, struct tegra_dsi_state, base);
 }
 
+struct tegra_dsi_config {
+	bool has_multiple_pad_controls;
+	bool has_mux_parent_clk;
+};
+
 struct tegra_dsi {
 	struct host1x_client client;
 	struct tegra_output output;
@@ -83,6 +88,8 @@ struct tegra_dsi {
 	/* for ganged-mode support */
 	struct tegra_dsi *master;
 	struct tegra_dsi *slave;
+
+	const struct tegra_dsi_config *config;
 };
 
 static inline struct tegra_dsi *
@@ -665,39 +672,46 @@ static int tegra_dsi_pad_enable(struct tegra_dsi *dsi)
 {
 	u32 value;
 
-	value = DSI_PAD_CONTROL_VS1_PULLDN(0) | DSI_PAD_CONTROL_VS1_PDIO(0);
-	tegra_dsi_writel(dsi, value, DSI_PAD_CONTROL_0);
+	if (dsi->config->has_multiple_pad_controls) {
+		/*
+		 * XXX Is this still needed? The module reset is deasserted right
+		 * before this function is called.
+		 */
+		tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_0);
+		tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_1);
+		tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_2);
+		tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_3);
+		tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_4);
+
+		value = DSI_PAD_CONTROL_VS1_PULLDN(0) | DSI_PAD_CONTROL_VS1_PDIO(0);
+		tegra_dsi_writel(dsi, value, DSI_PAD_CONTROL_0);
+
+		value = DSI_PAD_SLEW_UP(0x7) | DSI_PAD_SLEW_DN(0x7) |
+			DSI_PAD_LP_UP(0x1) | DSI_PAD_LP_DN(0x1) |
+			DSI_PAD_OUT_CLK(0x0);
+		tegra_dsi_writel(dsi, value, DSI_PAD_CONTROL_2);
+
+		value = DSI_PAD_PREEMP_PD_CLK(0x3) | DSI_PAD_PREEMP_PU_CLK(0x3) |
+			DSI_PAD_PREEMP_PD(0x03) | DSI_PAD_PREEMP_PU(0x3);
+		tegra_dsi_writel(dsi, value, DSI_PAD_CONTROL_3);
+	} else {
+		value = DSI_PAD_CONTROL_LPUPADJ(0x1) | DSI_PAD_CONTROL_LPDNADJ(0x1) |
+			DSI_PAD_CONTROL_PREEMP_EN(0x1) | DSI_PAD_CONTROL_SLEWDNADJ(0x6) |
+			DSI_PAD_CONTROL_SLEWUPADJ(0x6) | DSI_PAD_CONTROL_PDIO(0) |
+			DSI_PAD_CONTROL_PDIO_CLK(0) | DSI_PAD_CONTROL_PULLDN_ENAB(0);
+		tegra_dsi_writel(dsi, value, DSI_PAD_CONTROL_0);
+	}
 
 	return 0;
 }
 
 static int tegra_dsi_pad_calibrate(struct tegra_dsi *dsi)
 {
-	u32 value;
 	int err;
 
-	/*
-	 * XXX Is this still needed? The module reset is deasserted right
-	 * before this function is called.
-	 */
-	tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_0);
-	tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_1);
-	tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_2);
-	tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_3);
-	tegra_dsi_writel(dsi, 0, DSI_PAD_CONTROL_4);
-
 	/* start calibration */
 	tegra_dsi_pad_enable(dsi);
 
-	value = DSI_PAD_SLEW_UP(0x7) | DSI_PAD_SLEW_DN(0x7) |
-		DSI_PAD_LP_UP(0x1) | DSI_PAD_LP_DN(0x1) |
-		DSI_PAD_OUT_CLK(0x0);
-	tegra_dsi_writel(dsi, value, DSI_PAD_CONTROL_2);
-
-	value = DSI_PAD_PREEMP_PD_CLK(0x3) | DSI_PAD_PREEMP_PU_CLK(0x3) |
-		DSI_PAD_PREEMP_PD(0x03) | DSI_PAD_PREEMP_PU(0x3);
-	tegra_dsi_writel(dsi, value, DSI_PAD_CONTROL_3);
-
 	err = tegra_mipi_start_calibration(dsi->mipi);
 	if (err < 0)
 		return err;
@@ -1174,6 +1188,12 @@ static int tegra_dsi_setup_clocks(struct tegra_dsi *dsi)
 	struct clk *parent;
 	int err;
 
+	/*
+	 * Tegra124+ uses a clock gate, not a mux, so this step
+	 * should be redundant for configuration; yet, DSI refuses
+	 * to work without it.
+	 */
+
 	parent = clk_get_parent(dsi->clk);
 	if (!parent)
 		return -EINVAL;
@@ -1562,6 +1582,10 @@ static int tegra_dsi_probe(struct platform_device *pdev)
 	if (!dsi)
 		return -ENOMEM;
 
+	dsi->config = device_get_match_data(&pdev->dev);
+	if (!dsi->config)
+		return -ENODEV;
+
 	dsi->output.dev = dsi->dev = &pdev->dev;
 	dsi->video_fifo_depth = 1920;
 	dsi->host_fifo_depth = 64;
@@ -1600,7 +1624,7 @@ static int tegra_dsi_probe(struct platform_device *pdev)
 		goto remove;
 	}
 
-	dsi->clk_lp = devm_clk_get(&pdev->dev, "lp");
+	dsi->clk_lp = devm_clk_get_optional(&pdev->dev, "lp");
 	if (IS_ERR(dsi->clk_lp)) {
 		err = dev_err_probe(&pdev->dev, PTR_ERR(dsi->clk_lp),
 				    "cannot get low-power clock\n");
@@ -1621,10 +1645,12 @@ static int tegra_dsi_probe(struct platform_device *pdev)
 		goto remove;
 	}
 
-	err = tegra_dsi_setup_clocks(dsi);
-	if (err < 0) {
-		dev_err(&pdev->dev, "cannot setup clocks\n");
-		goto remove;
+	if (dsi->config->has_mux_parent_clk) {
+		err = tegra_dsi_setup_clocks(dsi);
+		if (err < 0) {
+			dev_err(&pdev->dev, "cannot setup clocks\n");
+			goto remove;
+		}
 	}
 
 	dsi->regs = devm_platform_ioremap_resource(pdev, 0);
@@ -1688,11 +1714,40 @@ static void tegra_dsi_remove(struct platform_device *pdev)
 	tegra_mipi_free(dsi->mipi);
 }
 
+static const struct tegra_dsi_config tegra20_dsi_config = {
+	.has_multiple_pad_controls = false,
+	.has_mux_parent_clk = false,
+};
+
+/*
+ * Tegra30 allows DSIA/DSIB to be muxed to either PLL_D or PLL_D2; this is
+ * simply not modeled in the clock driver yet. If this functionality is
+ * required, the has_mux_parent_clk flag can be set to true once the clock
+ * driver is patched.
+ */
+static const struct tegra_dsi_config tegra30_dsi_config = {
+	.has_multiple_pad_controls = false,
+	.has_mux_parent_clk = false,
+};
+
+static const struct tegra_dsi_config tegra114_dsi_config = {
+	.has_multiple_pad_controls = true,
+	.has_mux_parent_clk = true,
+};
+
+/* TODO: figure out why has_mux_parent_clk = true is necessary on Tegra124+ */
+static const struct tegra_dsi_config tegra124_dsi_config = {
+	.has_multiple_pad_controls = true,
+	.has_mux_parent_clk = true,
+};
+
 static const struct of_device_id tegra_dsi_of_match[] = {
-	{ .compatible = "nvidia,tegra210-dsi", },
-	{ .compatible = "nvidia,tegra132-dsi", },
-	{ .compatible = "nvidia,tegra124-dsi", },
-	{ .compatible = "nvidia,tegra114-dsi", },
+	{ .compatible = "nvidia,tegra210-dsi", .data = &tegra124_dsi_config },
+	{ .compatible = "nvidia,tegra132-dsi", .data = &tegra124_dsi_config },
+	{ .compatible = "nvidia,tegra124-dsi", .data = &tegra124_dsi_config },
+	{ .compatible = "nvidia,tegra114-dsi", .data = &tegra114_dsi_config },
+	{ .compatible = "nvidia,tegra30-dsi", .data = &tegra30_dsi_config },
+	{ .compatible = "nvidia,tegra20-dsi", .data = &tegra20_dsi_config },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, tegra_dsi_of_match);
diff --git a/drivers/gpu/drm/tegra/dsi.h b/drivers/gpu/drm/tegra/dsi.h
index f39594e65e97..d834ac0c47ab 100644
--- a/drivers/gpu/drm/tegra/dsi.h
+++ b/drivers/gpu/drm/tegra/dsi.h
@@ -95,6 +95,16 @@
 #define DSI_TALLY_LRX(x)		(((x) & 0xff) <<  8)
 #define DSI_TALLY_HTX(x)		(((x) & 0xff) <<  0)
 #define DSI_PAD_CONTROL_0		0x4b
+/* Tegra20/Tegra30 */
+#define DSI_PAD_CONTROL_PULLDN_ENAB(x)	(((x) & 0x1) << 28)
+#define DSI_PAD_CONTROL_SLEWUPADJ(x)	(((x) & 0x7) << 24)
+#define DSI_PAD_CONTROL_SLEWDNADJ(x)	(((x) & 0x7) << 20)
+#define DSI_PAD_CONTROL_PREEMP_EN(x)	(((x) & 0x1) << 19)
+#define DSI_PAD_CONTROL_PDIO_CLK(x)	(((x) & 0x1) << 18)
+#define DSI_PAD_CONTROL_PDIO(x)		(((x) & 0x3) << 16)
+#define DSI_PAD_CONTROL_LPUPADJ(x)	(((x) & 0x3) << 14)
+#define DSI_PAD_CONTROL_LPDNADJ(x)	(((x) & 0x3) << 12)
+/* Tegra114+ */
 #define DSI_PAD_CONTROL_VS1_PDIO(x)	(((x) & 0xf) <<  0)
 #define DSI_PAD_CONTROL_VS1_PDIO_CLK	(1 <<  8)
 #define DSI_PAD_CONTROL_VS1_PULLDN(x)	(((x) & 0xf) << 16)
-- 
2.51.0

[PATCH v4 2/2 RESEND] drm/tegra: dsi: re-add clear enable register if DSI was powered by bootloader

[Svyatoslav Ryhel]

Original commit b22fd0b9639e ("drm/tegra: dsi: Clear enable register if
powered by bootloader") was added to address the issue of DSI being in an
unknown state after the bootloader, ensuring correct panel configuration.
This worked fairly well under the assumption that the bootloader had set
up DSI; however, in cases where it did not, the device would hang because
a DSI read was called before the DSI hardware was ready.

Removing this workaround results in the issue described in the original
fix: the panel initialization sequence fails and the panel gets stuck in
an undefined state. This is especially noticeable with command mode panels

In order to properly address this issue, the original workaround is
restored and placed after the DSI hardware is prepared for R/W operations.
This fixes behavior for both cases: where DSI is set by the bootloader and
where DSI is untouched.

I have tested this change on Tegra20 (Motorola Atrix 4G),
Tegra114 (NVIDIA Tegra Note 7 and ASUS Transformer Pad TF701T), and
Tegra124 (Xiaomi Mi Pad) with U-Boot, using both bootloader-initialized
DSI and untouched DSI.

Fixes: b22fd0b9639e ("drm/tegra: dsi: Clear enable register if powered by bootloader")
Fixes: 660b299bed2a ("Revert "drm/tegra: dsi: Clear enable register if powered by bootloader"")
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
---
 drivers/gpu/drm/tegra/dsi.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/gpu/drm/tegra/dsi.c b/drivers/gpu/drm/tegra/dsi.c
index fbab10bc5c41..e7fdd8c7ac12 100644
--- a/drivers/gpu/drm/tegra/dsi.c
+++ b/drivers/gpu/drm/tegra/dsi.c
@@ -936,6 +936,15 @@ static void tegra_dsi_encoder_enable(struct drm_encoder *encoder)
 		return;
 	}
 
+	/* If the bootloader enabled DSI it needs to be disabled
+	 * in order for the panel initialization commands to be
+	 * properly sent.
+	 */
+	value = tegra_dsi_readl(dsi, DSI_POWER_CONTROL);
+
+	if (value & DSI_POWER_CONTROL_ENABLE)
+		tegra_dsi_disable(dsi);
+
 	state = tegra_dsi_get_state(dsi);
 
 	tegra_dsi_set_timeout(dsi, state->bclk, state->vrefresh);
-- 
2.51.0