* [V2,2/5] usb: serial: f81534: add auto RTS direction support
@ 2018-01-04 2:29 Ji-Ze Hong (Peter Hong)
0 siblings, 0 replies; 2+ messages in thread
From: Ji-Ze Hong (Peter Hong) @ 2018-01-04 2:29 UTC (permalink / raw)
To: johan; +Cc: gregkh, linux-usb, linux-kernel, peter_hong,
Ji-Ze Hong (Peter Hong)
The F81532/534 had auto RTS direction support for RS485 mode.
We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
There are 4 conditions below:
0: F81534_PORT_CONF_RS232.
1: F81534_PORT_CONF_RS485.
2: value error, default to F81534_PORT_CONF_RS232.
3: F81534_PORT_CONF_RS485_INVERT.
F81532/534 Clock register (offset +08h)
Bit0: UART Enable (always on)
Bit2-1: Clock source selector
00: 1.846MHz.
01: 18.46MHz.
10: 24MHz.
11: 14.77MHz.
Bit4: Auto direction(RTS) control (RTS pin Low when TX)
Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
---
V2:
1: Read the configure data from flash and save it to shadow clock
register.
drivers/usb/serial/f81534.c | 34 +++++++++++++++++++++++++++++++++-
1 file changed, 33 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 758ef0424164..8a778bc1d492 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -98,11 +98,16 @@
#define F81534_DEFAULT_BAUD_RATE 9600
+#define F81534_PORT_CONF_RS232 0
+#define F81534_PORT_CONF_RS485 BIT(0)
+#define F81534_PORT_CONF_RS485_INVERT (BIT(0) | BIT(1))
#define F81534_PORT_CONF_DISABLE_PORT BIT(3)
#define F81534_PORT_CONF_NOT_EXIST_PORT BIT(7)
#define F81534_PORT_UNAVAILABLE \
(F81534_PORT_CONF_DISABLE_PORT | F81534_PORT_CONF_NOT_EXIST_PORT)
+#define F81534_UART_MODE_MASK (BIT(0) | BIT(1))
+
#define F81534_1X_RXTRIGGER 0xc3
#define F81534_8X_RXTRIGGER 0xcf
@@ -115,6 +120,8 @@
* 01: 18.46MHz.
* 10: 24MHz.
* 11: 14.77MHz.
+ * Bit4: Auto direction(RTS) control (RTS pin Low when TX)
+ * Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
*/
#define F81534_UART_EN BIT(0)
@@ -123,6 +130,9 @@
#define F81534_CLK_24_MHZ (F81534_UART_EN | BIT(2))
#define F81534_CLK_14_77_MHZ (F81534_UART_EN | BIT(1) | BIT(2))
+#define F81534_CLK_RS485_MODE BIT(4)
+#define F81534_CLK_RS485_INVERT BIT(5)
+
static const struct usb_device_id f81534_id_table[] = {
{ USB_DEVICE(FINTEK_VENDOR_ID_1, FINTEK_DEVICE_ID) },
{ USB_DEVICE(FINTEK_VENDOR_ID_2, FINTEK_DEVICE_ID) },
@@ -517,7 +527,8 @@ static int f81534_set_port_config(struct usb_serial_port *port,
}
port_priv->baud_base = baudrate_table[idx];
- port_priv->shadow_clk = clock_table[idx];
+ port_priv->shadow_clk &= ~F81534_CLK_14_77_MHZ;
+ port_priv->shadow_clk |= clock_table[idx];
status = f81534_set_port_register(port, F81534_CLOCK_REG,
port_priv->shadow_clk);
@@ -1269,9 +1280,12 @@ static void f81534_lsr_worker(struct work_struct *work)
static int f81534_port_probe(struct usb_serial_port *port)
{
+ struct f81534_serial_private *serial_priv;
struct f81534_port_private *port_priv;
int ret;
+ u8 value;
+ serial_priv = usb_get_serial_data(port->serial);
port_priv = devm_kzalloc(&port->dev, sizeof(*port_priv), GFP_KERNEL);
if (!port_priv)
return -ENOMEM;
@@ -1303,6 +1317,24 @@ static int f81534_port_probe(struct usb_serial_port *port)
if (ret)
return ret;
+ value = serial_priv->conf_data[port_priv->phy_num];
+ switch (value & F81534_UART_MODE_MASK) {
+ case F81534_PORT_CONF_RS485_INVERT:
+ port_priv->shadow_clk = F81534_CLK_RS485_MODE |
+ F81534_CLK_RS485_INVERT;
+ dev_info(&port->dev, "RS485 invert mode.\n");
+ break;
+ case F81534_PORT_CONF_RS485:
+ port_priv->shadow_clk = F81534_CLK_RS485_MODE;
+ dev_info(&port->dev, "RS485 mode.\n");
+ break;
+
+ default:
+ case F81534_PORT_CONF_RS232:
+ dev_info(&port->dev, "RS232 mode.\n");
+ break;
+ }
+
return 0;
}
^ permalink raw reply related [flat|nested] 2+ messages in thread
* [V2,2/5] usb: serial: f81534: add auto RTS direction support
@ 2018-01-09 11:14 Johan Hovold
0 siblings, 0 replies; 2+ messages in thread
From: Johan Hovold @ 2018-01-09 11:14 UTC (permalink / raw)
To: Ji-Ze Hong (Peter Hong)
Cc: johan, gregkh, linux-usb, linux-kernel, peter_hong,
Ji-Ze Hong (Peter Hong)
On Thu, Jan 04, 2018 at 10:29:18AM +0800, Ji-Ze Hong (Peter Hong) wrote:
> The F81532/534 had auto RTS direction support for RS485 mode.
> We'll read it from internal Flash with address 0x2f01~0x2f04 for 4 ports.
> There are 4 conditions below:
> 0: F81534_PORT_CONF_RS232.
> 1: F81534_PORT_CONF_RS485.
> 2: value error, default to F81534_PORT_CONF_RS232.
> 3: F81534_PORT_CONF_RS485_INVERT.
>
> F81532/534 Clock register (offset +08h)
>
> Bit0: UART Enable (always on)
> Bit2-1: Clock source selector
> 00: 1.846MHz.
> 01: 18.46MHz.
> 10: 24MHz.
> 11: 14.77MHz.
> Bit4: Auto direction(RTS) control (RTS pin Low when TX)
> Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
>
> Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
> ---
> V2:
> 1: Read the configure data from flash and save it to shadow clock
> register.
>
> drivers/usb/serial/f81534.c | 34 +++++++++++++++++++++++++++++++++-
> 1 file changed, 33 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
> index 758ef0424164..8a778bc1d492 100644
> --- a/drivers/usb/serial/f81534.c
> +++ b/drivers/usb/serial/f81534.c
> @@ -98,11 +98,16 @@
>
> #define F81534_DEFAULT_BAUD_RATE 9600
>
> +#define F81534_PORT_CONF_RS232 0
> +#define F81534_PORT_CONF_RS485 BIT(0)
> +#define F81534_PORT_CONF_RS485_INVERT (BIT(0) | BIT(1))
> #define F81534_PORT_CONF_DISABLE_PORT BIT(3)
> #define F81534_PORT_CONF_NOT_EXIST_PORT BIT(7)
> #define F81534_PORT_UNAVAILABLE \
> (F81534_PORT_CONF_DISABLE_PORT | F81534_PORT_CONF_NOT_EXIST_PORT)
>
> +#define F81534_UART_MODE_MASK (BIT(0) | BIT(1))
Use GENMASK()?
> +
> #define F81534_1X_RXTRIGGER 0xc3
> #define F81534_8X_RXTRIGGER 0xcf
>
> @@ -115,6 +120,8 @@
> * 01: 18.46MHz.
> * 10: 24MHz.
> * 11: 14.77MHz.
> + * Bit4: Auto direction(RTS) control (RTS pin Low when TX)
> + * Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX)
> */
>
> #define F81534_UART_EN BIT(0)
> @@ -123,6 +130,9 @@
> #define F81534_CLK_24_MHZ (F81534_UART_EN | BIT(2))
> #define F81534_CLK_14_77_MHZ (F81534_UART_EN | BIT(1) | BIT(2))
>
> +#define F81534_CLK_RS485_MODE BIT(4)
> +#define F81534_CLK_RS485_INVERT BIT(5)
> +
> static const struct usb_device_id f81534_id_table[] = {
> { USB_DEVICE(FINTEK_VENDOR_ID_1, FINTEK_DEVICE_ID) },
> { USB_DEVICE(FINTEK_VENDOR_ID_2, FINTEK_DEVICE_ID) },
> @@ -517,7 +527,8 @@ static int f81534_set_port_config(struct usb_serial_port *port,
> }
>
> port_priv->baud_base = baudrate_table[idx];
> - port_priv->shadow_clk = clock_table[idx];
> + port_priv->shadow_clk &= ~F81534_CLK_14_77_MHZ;
Add a dedicated mask define instead of using a clock value here. No need
to clear the enable bit for example (which shouldn't be part of the
clock value as I mentioned earlier).
> + port_priv->shadow_clk |= clock_table[idx];
>
> status = f81534_set_port_register(port, F81534_CLOCK_REG,
> port_priv->shadow_clk);
> @@ -1269,9 +1280,12 @@ static void f81534_lsr_worker(struct work_struct *work)
>
> static int f81534_port_probe(struct usb_serial_port *port)
> {
> + struct f81534_serial_private *serial_priv;
> struct f81534_port_private *port_priv;
> int ret;
> + u8 value;
>
> + serial_priv = usb_get_serial_data(port->serial);
> port_priv = devm_kzalloc(&port->dev, sizeof(*port_priv), GFP_KERNEL);
> if (!port_priv)
> return -ENOMEM;
> @@ -1303,6 +1317,24 @@ static int f81534_port_probe(struct usb_serial_port *port)
> if (ret)
> return ret;
>
> + value = serial_priv->conf_data[port_priv->phy_num];
> + switch (value & F81534_UART_MODE_MASK) {
> + case F81534_PORT_CONF_RS485_INVERT:
> + port_priv->shadow_clk = F81534_CLK_RS485_MODE |
> + F81534_CLK_RS485_INVERT;
> + dev_info(&port->dev, "RS485 invert mode.\n");
> + break;
> + case F81534_PORT_CONF_RS485:
> + port_priv->shadow_clk = F81534_CLK_RS485_MODE;
> + dev_info(&port->dev, "RS485 mode.\n");
> + break;
> +
> + default:
> + case F81534_PORT_CONF_RS232:
> + dev_info(&port->dev, "RS232 mode.\n");
Again, I think these dev_info should really be dev_dbg.
> + break;
> + }
> +
> return 0;
> }
Johan
---
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2018-01-09 11:14 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2018-01-04 2:29 [V2,2/5] usb: serial: f81534: add auto RTS direction support Ji-Ze Hong (Peter Hong)
-- strict thread matches above, loose matches on Subject: below --
2018-01-09 11:14 Johan Hovold
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).