* [PATCH] usb: misc: usb3503: Use gpio descriptor interface
@ 2020-01-23 14:42 ` Pavel Löbl
2020-01-24 6:33 ` Marek Szyprowski
0 siblings, 1 reply; 4+ messages in thread
From: Pavel Löbl @ 2020-01-23 14:42 UTC (permalink / raw)
To: linux-usb; +Cc: gregkh, m.szyprowski, Pavel Löbl
Move gpio related code to descriptor-based interface. This makes
driver to respect active physical level as specified in DT. Existing
DT nodes are adjusted to reflect the former behaviour.
Signed-off-by: Pavel Löbl <pavel@loebl.cz>
---
arch/arm/boot/dts/exynos5250-arndale.dts | 4 +-
.../boot/dts/sun8i-a83t-cubietruck-plus.dts | 2 +-
arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 2 +-
drivers/usb/misc/usb3503.c | 79 +++++++------------
include/linux/platform_data/usb3503.h | 6 +-
5 files changed, 35 insertions(+), 58 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index d6c85efdb465..344e15a4c959 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -153,8 +153,8 @@ xxti {
usb_hub: usb-hub {
compatible = "smsc,usb3503a";
- reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
- connect-gpios = <&gpd1 7 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>;
+ connect-gpios = <&gpd1 7 GPIO_ACTIVE_HIGH>;
};
};
diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
index d9be511f054f..fb928503ad45 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
@@ -101,7 +101,7 @@ usb-hub {
initial-mode = <1>; /* initialize in HUB mode */
disabled-ports = <1>;
intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
- reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
+ reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
refclk-frequency = <19200000>;
};
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
index e12a36ce5d93..a1d3575edb39 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
@@ -498,7 +498,7 @@ wcnss@a21b000 {
usb2513 {
compatible = "smsc,usb3503";
- reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_HIGH>;
initial-mode = <1>;
};
diff --git a/drivers/usb/misc/usb3503.c b/drivers/usb/misc/usb3503.c
index 72f39a9751b5..d9ffb2d5c318 100644
--- a/drivers/usb/misc/usb3503.c
+++ b/drivers/usb/misc/usb3503.c
@@ -47,19 +47,19 @@ struct usb3503 {
struct device *dev;
struct clk *clk;
u8 port_off_mask;
- int gpio_intn;
- int gpio_reset;
- int gpio_connect;
+ struct gpio_desc *gpio_intn;
+ struct gpio_desc *gpio_reset;
+ struct gpio_desc *gpio_connect;
bool secondary_ref_clk;
};
static int usb3503_reset(struct usb3503 *hub, int state)
{
- if (!state && gpio_is_valid(hub->gpio_connect))
- gpio_set_value_cansleep(hub->gpio_connect, 0);
+ if (!state && hub->gpio_connect)
+ gpiod_set_value_cansleep(hub->gpio_connect, 0);
- if (gpio_is_valid(hub->gpio_reset))
- gpio_set_value_cansleep(hub->gpio_reset, state);
+ if (hub->gpio_reset)
+ gpiod_set_value_cansleep(hub->gpio_reset, state);
/* Wait T_HUBINIT == 4ms for hub logic to stabilize */
if (state)
@@ -115,8 +115,8 @@ static int usb3503_connect(struct usb3503 *hub)
}
}
- if (gpio_is_valid(hub->gpio_connect))
- gpio_set_value_cansleep(hub->gpio_connect, 1);
+ if (hub->gpio_connect)
+ gpiod_set_value_cansleep(hub->gpio_connect, 1);
hub->mode = USB3503_MODE_HUB;
dev_info(dev, "switched to HUB mode\n");
@@ -164,6 +164,7 @@ static int usb3503_probe(struct usb3503 *hub)
u32 mode = USB3503_MODE_HUB;
const u32 *property;
int len;
+ int intn_level;
if (pdata) {
hub->port_off_mask = pdata->port_off_mask;
@@ -230,59 +231,35 @@ static int usb3503_probe(struct usb3503 *hub)
}
}
- hub->gpio_intn = of_get_named_gpio(np, "intn-gpios", 0);
- if (hub->gpio_intn == -EPROBE_DEFER)
- return -EPROBE_DEFER;
- hub->gpio_connect = of_get_named_gpio(np, "connect-gpios", 0);
- if (hub->gpio_connect == -EPROBE_DEFER)
- return -EPROBE_DEFER;
- hub->gpio_reset = of_get_named_gpio(np, "reset-gpios", 0);
- if (hub->gpio_reset == -EPROBE_DEFER)
- return -EPROBE_DEFER;
- of_property_read_u32(np, "initial-mode", &mode);
- hub->mode = mode;
- }
-
- if (hub->port_off_mask && !hub->regmap)
- dev_err(dev, "Ports disabled with no control interface\n");
-
- if (gpio_is_valid(hub->gpio_intn)) {
- int val = hub->secondary_ref_clk ? GPIOF_OUT_INIT_LOW :
- GPIOF_OUT_INIT_HIGH;
- err = devm_gpio_request_one(dev, hub->gpio_intn, val,
- "usb3503 intn");
+ intn_level = hub->secondary_ref_clk ? GPIOD_OUT_LOW : GPIOD_OUT_HIGH;
+ hub->gpio_intn = devm_gpiod_get_optional(dev, "intn", intn_level);
+ err = PTR_ERR_OR_ZERO(hub->gpio_intn);
if (err) {
- dev_err(dev,
- "unable to request GPIO %d as interrupt pin (%d)\n",
- hub->gpio_intn, err);
+ if (err != -EPROBE_DEFER)
+ dev_err(dev, "failed to get interrupt GPIO");
return err;
}
- }
-
- if (gpio_is_valid(hub->gpio_connect)) {
- err = devm_gpio_request_one(dev, hub->gpio_connect,
- GPIOF_OUT_INIT_LOW, "usb3503 connect");
+ hub->gpio_connect = devm_gpiod_get_optional(dev, "connect", GPIOD_OUT_LOW);
+ err = PTR_ERR_OR_ZERO(hub->gpio_connect);
if (err) {
- dev_err(dev,
- "unable to request GPIO %d as connect pin (%d)\n",
- hub->gpio_connect, err);
+ if (err != -EPROBE_DEFER)
+ dev_err(dev, "failed to get GPIO for connect");
return err;
}
- }
-
- if (gpio_is_valid(hub->gpio_reset)) {
- err = devm_gpio_request_one(dev, hub->gpio_reset,
- GPIOF_OUT_INIT_LOW, "usb3503 reset");
- /* Datasheet defines a hardware reset to be at least 100us */
- usleep_range(100, 10000);
+ hub->gpio_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ err = PTR_ERR_OR_ZERO(hub->gpio_reset);
if (err) {
- dev_err(dev,
- "unable to request GPIO %d as reset pin (%d)\n",
- hub->gpio_reset, err);
+ if (err != -EPROBE_DEFER)
+ dev_err(dev, "failed to get reset GPIO");
return err;
}
+ of_property_read_u32(np, "initial-mode", &mode);
+ hub->mode = mode;
}
+ if (hub->port_off_mask && !hub->regmap)
+ dev_err(dev, "Ports disabled with no control interface\n");
+
usb3503_switch_mode(hub, hub->mode);
dev_info(dev, "%s: probed in %s mode\n", __func__,
diff --git a/include/linux/platform_data/usb3503.h b/include/linux/platform_data/usb3503.h
index e049d51c1353..3e966a62277e 100644
--- a/include/linux/platform_data/usb3503.h
+++ b/include/linux/platform_data/usb3503.h
@@ -17,9 +17,9 @@ enum usb3503_mode {
struct usb3503_platform_data {
enum usb3503_mode initial_mode;
u8 port_off_mask;
- int gpio_intn;
- int gpio_connect;
- int gpio_reset;
+ struct gpio_desc *gpio_intn;
+ struct gpio_desc *gpio_connect;
+ struct gpio_desc *gpio_reset;
};
#endif
--
2.24.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH] usb: misc: usb3503: Use gpio descriptor interface
2020-01-23 14:42 ` [PATCH] usb: misc: usb3503: Use gpio descriptor interface Pavel Löbl
@ 2020-01-24 6:33 ` Marek Szyprowski
2020-01-24 8:22 ` Greg KH
0 siblings, 1 reply; 4+ messages in thread
From: Marek Szyprowski @ 2020-01-24 6:33 UTC (permalink / raw)
To: Pavel Löbl, linux-usb; +Cc: gregkh, Linus Walleij
Hi Pavel,
On 23.01.2020 15:42, Pavel Löbl wrote:
> Move gpio related code to descriptor-based interface. This makes
> driver to respect active physical level as specified in DT. Existing
> DT nodes are adjusted to reflect the former behaviour.
>
> Signed-off-by: Pavel Löbl <pavel@loebl.cz>
This is a duplicate of https://patchwork.kernel.org/cover/11285261/
which has been already applied to current linux-next.
> ---
> arch/arm/boot/dts/exynos5250-arndale.dts | 4 +-
> .../boot/dts/sun8i-a83t-cubietruck-plus.dts | 2 +-
> arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 2 +-
> drivers/usb/misc/usb3503.c | 79 +++++++------------
> include/linux/platform_data/usb3503.h | 6 +-
> 5 files changed, 35 insertions(+), 58 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
> index d6c85efdb465..344e15a4c959 100644
> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> @@ -153,8 +153,8 @@ xxti {
> usb_hub: usb-hub {
> compatible = "smsc,usb3503a";
>
> - reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
> - connect-gpios = <&gpd1 7 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>;
> + connect-gpios = <&gpd1 7 GPIO_ACTIVE_HIGH>;
> };
> };
>
> diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
> index d9be511f054f..fb928503ad45 100644
> --- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
> +++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
> @@ -101,7 +101,7 @@ usb-hub {
> initial-mode = <1>; /* initialize in HUB mode */
> disabled-ports = <1>;
> intn-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
> - reset-gpios = <&pio 4 16 GPIO_ACTIVE_LOW>; /* PE16 */
> + reset-gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
> connect-gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
> refclk-frequency = <19200000>;
> };
> diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
> index e12a36ce5d93..a1d3575edb39 100644
> --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
> +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
> @@ -498,7 +498,7 @@ wcnss@a21b000 {
>
> usb2513 {
> compatible = "smsc,usb3503";
> - reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_HIGH>;
> initial-mode = <1>;
> };
>
> diff --git a/drivers/usb/misc/usb3503.c b/drivers/usb/misc/usb3503.c
> index 72f39a9751b5..d9ffb2d5c318 100644
> --- a/drivers/usb/misc/usb3503.c
> +++ b/drivers/usb/misc/usb3503.c
> @@ -47,19 +47,19 @@ struct usb3503 {
> struct device *dev;
> struct clk *clk;
> u8 port_off_mask;
> - int gpio_intn;
> - int gpio_reset;
> - int gpio_connect;
> + struct gpio_desc *gpio_intn;
> + struct gpio_desc *gpio_reset;
> + struct gpio_desc *gpio_connect;
> bool secondary_ref_clk;
> };
>
> static int usb3503_reset(struct usb3503 *hub, int state)
> {
> - if (!state && gpio_is_valid(hub->gpio_connect))
> - gpio_set_value_cansleep(hub->gpio_connect, 0);
> + if (!state && hub->gpio_connect)
> + gpiod_set_value_cansleep(hub->gpio_connect, 0);
>
> - if (gpio_is_valid(hub->gpio_reset))
> - gpio_set_value_cansleep(hub->gpio_reset, state);
> + if (hub->gpio_reset)
> + gpiod_set_value_cansleep(hub->gpio_reset, state);
>
> /* Wait T_HUBINIT == 4ms for hub logic to stabilize */
> if (state)
> @@ -115,8 +115,8 @@ static int usb3503_connect(struct usb3503 *hub)
> }
> }
>
> - if (gpio_is_valid(hub->gpio_connect))
> - gpio_set_value_cansleep(hub->gpio_connect, 1);
> + if (hub->gpio_connect)
> + gpiod_set_value_cansleep(hub->gpio_connect, 1);
>
> hub->mode = USB3503_MODE_HUB;
> dev_info(dev, "switched to HUB mode\n");
> @@ -164,6 +164,7 @@ static int usb3503_probe(struct usb3503 *hub)
> u32 mode = USB3503_MODE_HUB;
> const u32 *property;
> int len;
> + int intn_level;
>
> if (pdata) {
> hub->port_off_mask = pdata->port_off_mask;
> @@ -230,59 +231,35 @@ static int usb3503_probe(struct usb3503 *hub)
> }
> }
>
> - hub->gpio_intn = of_get_named_gpio(np, "intn-gpios", 0);
> - if (hub->gpio_intn == -EPROBE_DEFER)
> - return -EPROBE_DEFER;
> - hub->gpio_connect = of_get_named_gpio(np, "connect-gpios", 0);
> - if (hub->gpio_connect == -EPROBE_DEFER)
> - return -EPROBE_DEFER;
> - hub->gpio_reset = of_get_named_gpio(np, "reset-gpios", 0);
> - if (hub->gpio_reset == -EPROBE_DEFER)
> - return -EPROBE_DEFER;
> - of_property_read_u32(np, "initial-mode", &mode);
> - hub->mode = mode;
> - }
> -
> - if (hub->port_off_mask && !hub->regmap)
> - dev_err(dev, "Ports disabled with no control interface\n");
> -
> - if (gpio_is_valid(hub->gpio_intn)) {
> - int val = hub->secondary_ref_clk ? GPIOF_OUT_INIT_LOW :
> - GPIOF_OUT_INIT_HIGH;
> - err = devm_gpio_request_one(dev, hub->gpio_intn, val,
> - "usb3503 intn");
> + intn_level = hub->secondary_ref_clk ? GPIOD_OUT_LOW : GPIOD_OUT_HIGH;
> + hub->gpio_intn = devm_gpiod_get_optional(dev, "intn", intn_level);
> + err = PTR_ERR_OR_ZERO(hub->gpio_intn);
> if (err) {
> - dev_err(dev,
> - "unable to request GPIO %d as interrupt pin (%d)\n",
> - hub->gpio_intn, err);
> + if (err != -EPROBE_DEFER)
> + dev_err(dev, "failed to get interrupt GPIO");
> return err;
> }
> - }
> -
> - if (gpio_is_valid(hub->gpio_connect)) {
> - err = devm_gpio_request_one(dev, hub->gpio_connect,
> - GPIOF_OUT_INIT_LOW, "usb3503 connect");
> + hub->gpio_connect = devm_gpiod_get_optional(dev, "connect", GPIOD_OUT_LOW);
> + err = PTR_ERR_OR_ZERO(hub->gpio_connect);
> if (err) {
> - dev_err(dev,
> - "unable to request GPIO %d as connect pin (%d)\n",
> - hub->gpio_connect, err);
> + if (err != -EPROBE_DEFER)
> + dev_err(dev, "failed to get GPIO for connect");
> return err;
> }
> - }
> -
> - if (gpio_is_valid(hub->gpio_reset)) {
> - err = devm_gpio_request_one(dev, hub->gpio_reset,
> - GPIOF_OUT_INIT_LOW, "usb3503 reset");
> - /* Datasheet defines a hardware reset to be at least 100us */
> - usleep_range(100, 10000);
> + hub->gpio_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
> + err = PTR_ERR_OR_ZERO(hub->gpio_reset);
> if (err) {
> - dev_err(dev,
> - "unable to request GPIO %d as reset pin (%d)\n",
> - hub->gpio_reset, err);
> + if (err != -EPROBE_DEFER)
> + dev_err(dev, "failed to get reset GPIO");
> return err;
> }
> + of_property_read_u32(np, "initial-mode", &mode);
> + hub->mode = mode;
> }
>
> + if (hub->port_off_mask && !hub->regmap)
> + dev_err(dev, "Ports disabled with no control interface\n");
> +
> usb3503_switch_mode(hub, hub->mode);
>
> dev_info(dev, "%s: probed in %s mode\n", __func__,
> diff --git a/include/linux/platform_data/usb3503.h b/include/linux/platform_data/usb3503.h
> index e049d51c1353..3e966a62277e 100644
> --- a/include/linux/platform_data/usb3503.h
> +++ b/include/linux/platform_data/usb3503.h
> @@ -17,9 +17,9 @@ enum usb3503_mode {
> struct usb3503_platform_data {
> enum usb3503_mode initial_mode;
> u8 port_off_mask;
> - int gpio_intn;
> - int gpio_connect;
> - int gpio_reset;
> + struct gpio_desc *gpio_intn;
> + struct gpio_desc *gpio_connect;
> + struct gpio_desc *gpio_reset;
> };
>
> #endif
Best regards
--
Marek Szyprowski, PhD
Samsung R&D Institute Poland
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] usb: misc: usb3503: Use gpio descriptor interface
2020-01-24 6:33 ` Marek Szyprowski
@ 2020-01-24 8:22 ` Greg KH
2020-01-24 8:30 ` Marek Szyprowski
0 siblings, 1 reply; 4+ messages in thread
From: Greg KH @ 2020-01-24 8:22 UTC (permalink / raw)
To: Marek Szyprowski; +Cc: Pavel Löbl, linux-usb, Linus Walleij
On Fri, Jan 24, 2020 at 07:33:36AM +0100, Marek Szyprowski wrote:
> Hi Pavel,
>
> On 23.01.2020 15:42, Pavel Löbl wrote:
> > Move gpio related code to descriptor-based interface. This makes
> > driver to respect active physical level as specified in DT. Existing
> > DT nodes are adjusted to reflect the former behaviour.
> >
> > Signed-off-by: Pavel Löbl <pavel@loebl.cz>
>
> This is a duplicate of https://patchwork.kernel.org/cover/11285261/
> which has been already applied to current linux-next.
With the exception fof the dts changes :(
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] usb: misc: usb3503: Use gpio descriptor interface
2020-01-24 8:22 ` Greg KH
@ 2020-01-24 8:30 ` Marek Szyprowski
0 siblings, 0 replies; 4+ messages in thread
From: Marek Szyprowski @ 2020-01-24 8:30 UTC (permalink / raw)
To: Greg KH; +Cc: Pavel Löbl, linux-usb, Linus Walleij
Hi Greg,
On 24.01.2020 09:22, Greg KH wrote:
> On Fri, Jan 24, 2020 at 07:33:36AM +0100, Marek Szyprowski wrote:
>> On 23.01.2020 15:42, Pavel Löbl wrote:
>>> Move gpio related code to descriptor-based interface. This makes
>>> driver to respect active physical level as specified in DT. Existing
>>> DT nodes are adjusted to reflect the former behaviour.
>>>
>>> Signed-off-by: Pavel Löbl <pavel@loebl.cz>
>> This is a duplicate of https://patchwork.kernel.org/cover/11285261/
>> which has been already applied to current linux-next.
> With the exception fof the dts changes :(
DTS changes has been merged via respective arm-soc trees, see commits:
c2f59e8180c9311108872dba582b1b0146acb054
1c226017d3ec93547b58082bdf778d9db7401c95
5206265f78e4e313bc982e289248a239cb3409e2
Best regards
--
Marek Szyprowski, PhD
Samsung R&D Institute Poland
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2020-01-24 8:30 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <CGME20200123144414eucas1p220590ff849a8d9e534ab6aa3cf5ade28@eucas1p2.samsung.com>
2020-01-23 14:42 ` [PATCH] usb: misc: usb3503: Use gpio descriptor interface Pavel Löbl
2020-01-24 6:33 ` Marek Szyprowski
2020-01-24 8:22 ` Greg KH
2020-01-24 8:30 ` Marek Szyprowski
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox