[PATCH] usb: typec: ucsi: UCSI2.0 Get Error Status changes

[PATCH] usb: typec: ucsi: UCSI2.0 Get Error Status changes

[Pooja Katiyar]

Add support for UCSI 2.0 Get Error Status command to add connector
number field to the command structure.

Connector number field is extracted from the previous UCSI command
which has failed and is used to get the failure reason/Error using
Get Error Status command.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pooja Katiyar <pooja.katiyar@intel.com>
---

 drivers/usb/typec/ucsi/ucsi.c | 29 ++++++++++++++++++++++++++---
 drivers/usb/typec/ucsi/ucsi.h |  3 +++
 2 files changed, 29 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/typec/ucsi/ucsi.c b/drivers/usb/typec/ucsi/ucsi.c
index bd6ae92aa39e..d6037ec2a642 100644
--- a/drivers/usb/typec/ucsi/ucsi.c
+++ b/drivers/usb/typec/ucsi/ucsi.c
@@ -71,8 +71,9 @@ static int ucsi_acknowledge_connector_change(struct ucsi *ucsi)
 
 static int ucsi_exec_command(struct ucsi *ucsi, u64 command);
 
-static int ucsi_read_error(struct ucsi *ucsi)
+static int ucsi_read_error(struct ucsi *ucsi, u8 connector_num)
 {
+	u64 command;
 	u16 error;
 	int ret;
 
@@ -81,7 +82,8 @@ static int ucsi_read_error(struct ucsi *ucsi)
 	if (ret)
 		return ret;
 
-	ret = ucsi_exec_command(ucsi, UCSI_GET_ERROR_STATUS);
+	command = UCSI_GET_ERROR_STATUS | UCSI_CONNECTOR_NUMBER(connector_num);
+	ret = ucsi_exec_command(ucsi, command);
 	if (ret < 0)
 		return ret;
 
@@ -134,9 +136,30 @@ static int ucsi_read_error(struct ucsi *ucsi)
 
 static int ucsi_exec_command(struct ucsi *ucsi, u64 cmd)
 {
+	u8 connector_num;
 	u32 cci;
 	int ret;
 
+	if (ucsi->version > UCSI_VERSION_1_2) {
+		switch (UCSI_COMMAND(cmd)) {
+		case UCSI_GET_ALTERNATE_MODES:
+			connector_num = UCSI_GET_ALTMODE_GET_CONNECTOR_NUMBER(cmd);
+			break;
+		case UCSI_PPM_RESET:
+		case UCSI_CANCEL:
+		case UCSI_ACK_CC_CI:
+		case UCSI_SET_NOTIFICATION_ENABLE:
+		case UCSI_GET_CAPABILITY:
+			connector_num = 0;
+			break;
+		default:
+			connector_num = UCSI_DEFAULT_GET_CONNECTOR_NUMBER(cmd);
+			break;
+		}
+	} else {
+		connector_num = 0;
+	}
+
 	ret = ucsi->ops->sync_write(ucsi, UCSI_CONTROL, &cmd, sizeof(cmd));
 	if (ret)
 		return ret;
@@ -161,7 +184,7 @@ static int ucsi_exec_command(struct ucsi *ucsi, u64 cmd)
 	if (cci & UCSI_CCI_ERROR) {
 		if (cmd == UCSI_GET_ERROR_STATUS)
 			return -EIO;
-		return ucsi_read_error(ucsi);
+		return ucsi_read_error(ucsi, connector_num);
 	}
 
 	if (cmd == UCSI_CANCEL && cci & UCSI_CCI_CANCEL_COMPLETE) {
diff --git a/drivers/usb/typec/ucsi/ucsi.h b/drivers/usb/typec/ucsi/ucsi.h
index 0e7c92eb1b22..349fbdc819c7 100644
--- a/drivers/usb/typec/ucsi/ucsi.h
+++ b/drivers/usb/typec/ucsi/ucsi.h
@@ -111,6 +111,9 @@ void ucsi_connector_change(struct ucsi *ucsi, u8 num);
 #define UCSI_CONNECTOR_NUMBER(_num_)		((u64)(_num_) << 16)
 #define UCSI_COMMAND(_cmd_)			((_cmd_) & 0xff)
 
+#define UCSI_GET_ALTMODE_GET_CONNECTOR_NUMBER(_cmd_)	(((_cmd_) >> 24) & GENMASK(6, 0))
+#define UCSI_DEFAULT_GET_CONNECTOR_NUMBER(_cmd_)	(((_cmd_) >> 16) & GENMASK(6, 0))
+
 /* CONNECTOR_RESET command bits */
 #define UCSI_CONNECTOR_RESET_HARD		BIT(23) /* Deprecated in v1.1 */
 
-- 
2.34.1

Re: [PATCH] usb: typec: ucsi: UCSI2.0 Get Error Status changes

[Greg KH]

On Wed, Jun 05, 2024 at 05:32:11PM -0700, Pooja Katiyar wrote:
> Add support for UCSI 2.0 Get Error Status command to add connector
> number field to the command structure.
> 
> Connector number field is extracted from the previous UCSI command
> which has failed and is used to get the failure reason/Error using
> Get Error Status command.
> 
> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
> Signed-off-by: Pooja Katiyar <pooja.katiyar@intel.com>
> ---
> 
>  drivers/usb/typec/ucsi/ucsi.c | 29 ++++++++++++++++++++++++++---
>  drivers/usb/typec/ucsi/ucsi.h |  3 +++
>  2 files changed, 29 insertions(+), 3 deletions(-)
> 

Does not apply to my tree :(