[PATCH 1/2] usb: serial: fix typos in comments

[PATCH 1/2] usb: serial: fix typos in comments

[Hemanth Selam]

Fix typos in comments, reported by scripts/checkpatch.pl using the
misspelling list in scripts/spelling.txt.  Only touches comments, no code
changes.

Assisted-by: Cursor:claude-opus-5
Signed-off-by: Hemanth Selam <hemanth.selam@gmail.com>
---
 drivers/usb/serial/f81534.c           | 4 ++--
 drivers/usb/serial/ftdi_sio_ids.h     | 2 +-
 drivers/usb/serial/keyspan_usa28msg.h | 2 +-
 3 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c
index 0037767e4bbf..f0ab72d99d5e 100644
--- a/drivers/usb/serial/f81534.c
+++ b/drivers/usb/serial/f81534.c
@@ -83,7 +83,7 @@
 #define F81534_TOKEN_MSR_CHANGE		0x04
 
 /*
- * We used interal SPI bus to access FLASH section. We must wait the SPI bus to
+ * We used internal SPI bus to access FLASH section. We must wait the SPI bus to
  * idle if we performed any command.
  *
  * SPI Bus status register: F81534_BUS_REG_STATUS
@@ -755,7 +755,7 @@ static int f81534_find_config_idx(struct usb_serial *serial, u8 *index)
  * The F81532/534 will not report serial port to USB serial subsystem when
  * H/W DCD/DSR/CTS/RI/RX pin connected to ground.
  *
- * To detect RX pin status, we'll enable MCR interal loopback, disable it and
+ * To detect RX pin status, we'll enable MCR internal loopback, disable it and
  * delayed for 60ms. It connected to ground If LSR register report UART_LSR_BI.
  */
 static bool f81534_check_port_hw_disabled(struct usb_serial *serial, int phy)
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index 9c83c17853c8..a3481f159d9a 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -770,7 +770,7 @@
  * Definitions for Icom Inc. devices
  */
 #define ICOM_VID		0x0C26 /* Icom vendor ID */
-/* Note: ID-1 is a communications tranceiver for HAM-radio operators */
+/* Note: ID-1 is a communications transceiver for HAM-radio operators */
 #define ICOM_ID_1_PID		0x0004 /* ID-1 USB to RS-232 */
 /* Note: OPC is an Optional cable to connect an Icom Tranceiver */
 #define ICOM_OPC_U_UC_PID	0x0018 /* OPC-478UC, OPC-1122U cloning cable */
diff --git a/drivers/usb/serial/keyspan_usa28msg.h b/drivers/usb/serial/keyspan_usa28msg.h
index a19f3fe5d98d..11003527da5c 100644
--- a/drivers/usb/serial/keyspan_usa28msg.h
+++ b/drivers/usb/serial/keyspan_usa28msg.h
@@ -61,7 +61,7 @@
 	with a total data length of 63.
 
 	USB IN (USA28 -> host, receive) messages contain data and parity
-	if parity is configred, thusly:
+	if parity is configured, thusly:
 	
 		DAT PAR DAT PAR DAT PAR ...
 
-- 
2.48.1

[PATCH 2/2] usb: serial: fix repeated words in comments

[Hemanth Selam]

Drop words accidentally written twice, reported by checkpatch.pl as a
possible repeated word.  Only touches comments, no code changes.

Assisted-by: Cursor:claude-opus-5
Signed-off-by: Hemanth Selam <hemanth.selam@gmail.com>
---
 drivers/usb/serial/mct_u232.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/serial/mct_u232.h b/drivers/usb/serial/mct_u232.h
index e3d09a83cab1..f79a1f1b6a98 100644
--- a/drivers/usb/serial/mct_u232.h
+++ b/drivers/usb/serial/mct_u232.h
@@ -273,13 +273,13 @@ static int mct_u232_calculate_baud_rate(struct usb_serial *serial,
  *  Bit 5: Data Set Ready (DSR). Reflects the state of the DSR line on the UART.
  *  Bit 4: Clear To Send (CTS). Reflects the state of the CTS line on the UART.
  *  Bit 3: Delta Data Carrier Detect (DDCD). Set to "1" if the -DCD line has
- *	   changed state one more more times since the last time the MSR was
+ *	   changed state one more times since the last time the MSR was
  *	   read by the host.
  *  Bit 2: Trailing Edge Ring Indicator (TERI). Set to "1" if the -RI line has
  *	   had a low to high transition since the last time the MSR was read by
  *	   the host.
  *  Bit 1: Delta Data Set Ready (DDSR). Set to "1" if the -DSR line has changed
- *	   state one more more times since the last time the MSR was read by the
+ *	   state one more times since the last time the MSR was read by the
  *	   host.
  *  Bit 0: Delta Clear To Send (DCTS). Set to "1" if the -CTS line has changed
  *	   state one more times since the last time the MSR was read by the
-- 
2.48.1