* [PATCH 2/2 v3] Watchdog: Add marvell octeontx2 watchdog driver
2023-04-25 8:19 [PATCH 1/2 v3] dt-bindings: watchdog: marvell octeonTX2 GTI system watchdog driver Bharat Bhushan
@ 2023-04-25 8:19 ` Bharat Bhushan
2023-04-26 19:15 ` Sunil Kovvuri Goutham
2023-05-02 6:38 ` kernel test robot
2023-04-25 19:00 ` [PATCH 1/2 v3] dt-bindings: watchdog: marvell octeonTX2 GTI system " Rob Herring
1 sibling, 2 replies; 5+ messages in thread
From: Bharat Bhushan @ 2023-04-25 8:19 UTC (permalink / raw)
To: wim, linux, robh+dt, krzysztof.kozlowski+dt, linux-watchdog,
devicetree, linux-kernel, sgoutham
Cc: Bharat Bhushan
This patch add support for Marvell OcteonTX2 watchdog. OcteonTX2
Global timer unit (GTI) support hardware watchdog timer. Software
programs watchdog timer to generate interrupt on first timeout,
second timeout is configured to be ignored and system reboots on
third timeout.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
---
v3:
- No changes
drivers/watchdog/Kconfig | 11 ++
drivers/watchdog/Makefile | 1 +
drivers/watchdog/octeontx2_wdt.c | 271 +++++++++++++++++++++++++++++++
3 files changed, 283 insertions(+)
create mode 100644 drivers/watchdog/octeontx2_wdt.c
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index f0872970daf9..bd52461a19f2 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -1779,6 +1779,17 @@ config OCTEON_WDT
from the first interrupt, it is then only poked when the
device is written.
+config OCTEONTX2_WATCHDOG
+ tristate "OCTEONTX2 Watchdog driver"
+ depends on ARCH_THUNDER || COMPILE_TEST
+ help
+ OCTEONTX2 GTI hardware supports watchdog timer. First timeout
+ works as watchdog pretimeout and installed interrupt handler
+ will be called on first timeout. Hardware can generate interrupt
+ to SCP on second timeout but it is not enabled, So second
+ timeout is ignored. If device poke does not happen then system
+ will reboot on third timeout.
+
config BCM2835_WDT
tristate "Broadcom BCM2835 hardware watchdog"
depends on ARCH_BCM2835 || (OF && COMPILE_TEST)
diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
index 9cbf6580f16c..aabe1afb0007 100644
--- a/drivers/watchdog/Makefile
+++ b/drivers/watchdog/Makefile
@@ -98,6 +98,7 @@ obj-$(CONFIG_VISCONTI_WATCHDOG) += visconti_wdt.o
obj-$(CONFIG_MSC313E_WATCHDOG) += msc313e_wdt.o
obj-$(CONFIG_APPLE_WATCHDOG) += apple_wdt.o
obj-$(CONFIG_SUNPLUS_WATCHDOG) += sunplus_wdt.o
+obj-$(CONFIG_OCTEONTX2_WATCHDOG) += octeontx2_wdt.o
# X86 (i386 + ia64 + x86_64) Architecture
obj-$(CONFIG_ACQUIRE_WDT) += acquirewdt.o
diff --git a/drivers/watchdog/octeontx2_wdt.c b/drivers/watchdog/octeontx2_wdt.c
new file mode 100644
index 000000000000..564a1ba2bf21
--- /dev/null
+++ b/drivers/watchdog/octeontx2_wdt.c
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Marvell Octeontx2 Watchdog driver
+ *
+ * Copyright (C) 2023 Marvell International Ltd.
+ */
+
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/watchdog.h>
+
+#include <asm/arch_timer.h>
+
+/*
+ * Hardware supports following mode of operation:
+ * 1) Interrupt Only:
+ * This will generate the interrupt to arm core whenever timeout happens.
+ *
+ * 2) Interrupt + del3t (Interrupt to firmware (SCP processor)).
+ * This will generate interrupt to arm core on 1st timeout happens
+ * This will generate interrupt to SCP processor on 2nd timeout happens
+ *
+ * 3) Interrupt + Interrupt to SCP processor (called delt3t) + reboot.
+ * This will generate interrupt to arm core on 1st timeout happens
+ * Will generate interrupt to SCP processor on 2nd timeout happens,
+ * if interrupt is configured.
+ * Reboot on 3rd timeout.
+ *
+ * Driver will use hardware in mode-3 above so that system can reboot in case
+ * a hardware hang. Also h/w is configured not to generate SCP interrupt, so
+ * effectively 2nd timeout is ignored within hardware.
+ */
+
+
+/* GTI CWD Watchdog Registers */
+#define GTI_CWD_GLOBAL_WDOG_IDX 63
+#define GTI_CWD_WDOG (0x8 * GTI_CWD_GLOBAL_WDOG_IDX)
+#define GTI_CWD_WDOG_MODE_INT_DEL3T_RST 0x3
+#define GTI_CWD_WDOG_MODE_MASK 0x3
+#define GTI_CWD_WDOG_LEN_SHIFT 4
+#define GTI_CWD_WDOG_CNT_SHIFT 20
+
+/* GTI Per-core Watchdog Interrupt Register */
+#define GTI_CWD_INT 0x200
+#define GTI_CWD_INT_PENDING_STATUS (1ULL << GTI_CWD_GLOBAL_WDOG_IDX)
+
+/* GTI Per-core Watchdog Interrupt Enable Clear Register */
+#define GTI_CWD_INT_ENA_CLR 0x210
+#define GTI_CWD_INT_ENA_CLR_VAL (1ULL << GTI_CWD_GLOBAL_WDOG_IDX)
+
+/* GTI Per-core Watchdog Interrupt Enable Set Register */
+#define GTI_CWD_INT_ENA_SET 0x218
+#define GTI_CWD_INT_ENA_SET_VAL (1ULL << GTI_CWD_GLOBAL_WDOG_IDX)
+
+/* GTI Per-core Watchdog Poke Registers */
+#define GTI_CWD_POKE (0x10000 + 0x8 * GTI_CWD_GLOBAL_WDOG_IDX)
+#define GTI_CWD_POKE_VAL (1ULL << GTI_CWD_GLOBAL_WDOG_IDX)
+
+struct octeontx2_wdt_priv {
+ struct watchdog_device wdev;
+ void __iomem *base;
+ u64 clock_freq;
+ int irq;
+};
+
+static irqreturn_t octeontx2_wdt_interrupt(int irq, void *data)
+{
+ struct watchdog_device *wdev = data;
+ struct octeontx2_wdt_priv *priv = watchdog_get_drvdata(wdev);
+
+ /* Clear Interrupt Pending Status */
+ writeq(GTI_CWD_INT_PENDING_STATUS, priv->base + GTI_CWD_INT);
+
+ watchdog_notify_pretimeout(wdev);
+
+ return IRQ_HANDLED;
+}
+
+static int octeontx2_wdt_ping(struct watchdog_device *wdev)
+{
+ struct octeontx2_wdt_priv *priv = watchdog_get_drvdata(wdev);
+
+ writeq(GTI_CWD_POKE_VAL, priv->base + GTI_CWD_POKE);
+
+ return 0;
+}
+
+static int octeontx2_wdt_start(struct watchdog_device *wdev)
+{
+ struct octeontx2_wdt_priv *priv = watchdog_get_drvdata(wdev);
+ u64 regval;
+
+ if (!wdev->pretimeout)
+ return -EINVAL;
+
+ set_bit(WDOG_HW_RUNNING, &wdev->status);
+
+ /* Clear any pending interrupt */
+ writeq(GTI_CWD_INT_PENDING_STATUS, priv->base + GTI_CWD_INT);
+
+ /* Enable Interrupt */
+ writeq(GTI_CWD_INT_ENA_SET_VAL, priv->base + GTI_CWD_INT_ENA_SET);
+
+ /* Set (Interrupt + SCP interrupt (DEL3T) + core domain reset) Mode */
+ regval = readq(priv->base + GTI_CWD_WDOG);
+ regval |= GTI_CWD_WDOG_MODE_INT_DEL3T_RST;
+ writeq(regval, priv->base + GTI_CWD_WDOG);
+
+ return 0;
+}
+
+static int octeontx2_wdt_stop(struct watchdog_device *wdev)
+{
+ struct octeontx2_wdt_priv *priv = watchdog_get_drvdata(wdev);
+ u64 regval;
+
+ /* Disable Interrupt */
+ writeq(GTI_CWD_INT_ENA_CLR_VAL, priv->base + GTI_CWD_INT_ENA_CLR);
+
+ /* Set GTI_CWD_WDOG.Mode = 0 to stop the timer */
+ regval = readq(priv->base + GTI_CWD_WDOG);
+ regval &= ~GTI_CWD_WDOG_MODE_MASK;
+ writeq(regval, priv->base + GTI_CWD_WDOG);
+
+ return 0;
+}
+
+static int octeontx2_wdt_settimeout(struct watchdog_device *wdev,
+ unsigned int timeout)
+{
+ struct octeontx2_wdt_priv *priv = watchdog_get_drvdata(wdev);
+ u64 timeout_wdog, regval;
+
+ /* Update new timeout */
+ wdev->timeout = timeout;
+
+ /* Pretimeout is 1/3 of timeout */
+ wdev->pretimeout = timeout / 3;
+ if (!wdev->pretimeout)
+ return -EINVAL;
+
+ /* Get clock cycles from timeout in second */
+ timeout_wdog = wdev->pretimeout * priv->clock_freq;
+
+ /* Watchdog counts in 1024 cycle steps */
+ timeout_wdog = timeout_wdog >> 10;
+
+ timeout_wdog = (timeout_wdog + 0xff) >> 8;
+ if (timeout_wdog >= 0x10000)
+ timeout_wdog = 0xffff;
+
+ /*
+ * GTI_CWD_WDOG.LEN have only upper 16-bits of 24-bits
+ * GTI_CWD_WDOG.CNT, need addition shift of 8.
+ */
+ regval = readq(priv->base + GTI_CWD_WDOG);
+ regval &= GTI_CWD_WDOG_MODE_MASK;
+ regval |= (timeout_wdog << (GTI_CWD_WDOG_CNT_SHIFT + 8)) |
+ (timeout_wdog << GTI_CWD_WDOG_LEN_SHIFT);
+ writeq(regval, priv->base + GTI_CWD_WDOG);
+
+ return 0;
+}
+
+static int octeontx2_wdt_set_pretimeout(struct watchdog_device *wdev,
+ unsigned int timeout)
+{
+ struct octeontx2_wdt_priv *priv = watchdog_get_drvdata(wdev);
+ struct watchdog_device *wdog_dev = &priv->wdev;
+
+ /* pretimeout should 1/3 of max_timeout */
+ if ((timeout * 3) <= wdog_dev->max_timeout)
+ return octeontx2_wdt_settimeout(wdev, timeout * 3);
+
+ return -EINVAL;
+}
+
+static const struct watchdog_info octeontx2_wdt_ident = {
+ .identity = "OcteonTX2 watchdog",
+ .options = WDIOF_SETTIMEOUT | WDIOF_PRETIMEOUT | WDIOF_KEEPALIVEPING |
+ WDIOF_MAGICCLOSE | WDIOF_CARDRESET,
+};
+
+static const struct watchdog_ops octeontx2_wdt_ops = {
+ .owner = THIS_MODULE,
+ .start = octeontx2_wdt_start,
+ .stop = octeontx2_wdt_stop,
+ .ping = octeontx2_wdt_ping,
+ .set_timeout = octeontx2_wdt_settimeout,
+ .set_pretimeout = octeontx2_wdt_set_pretimeout,
+};
+
+static int octeontx2_wdt_probe(struct platform_device *pdev)
+{
+ struct octeontx2_wdt_priv *priv;
+ struct device *dev = &pdev->dev;
+ struct watchdog_device *wdog_dev;
+ int irq;
+ int err;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->base))
+ return dev_err_probe(&pdev->dev, PTR_ERR(priv->base),
+ "reg property not valid/found\n");
+
+ priv->clock_freq = arch_timer_get_cntfrq();
+
+ wdog_dev = &priv->wdev;
+ wdog_dev->info = &octeontx2_wdt_ident,
+ wdog_dev->ops = &octeontx2_wdt_ops,
+ wdog_dev->parent = dev;
+ /*
+ * Watchdog counter is 24 bit where lower 8 bits are zeros, so maximum
+ * value that can be programmed in hardware is 0xffff00. This counter
+ * decrements every one microsec.
+ * Hardware will generate interrupt on first timeout (pretimeout)
+ * reset the system on 3rd timeout.
+ * Max watchdog pretimeout can be 16 sec, so max timeout is 48 sec.
+ * Let's have min pretimeout to 1sec, so min timeout is 3sec.
+ */
+ wdog_dev->max_timeout = 48;
+ wdog_dev->min_timeout = 3;
+ wdog_dev->timeout = 30;
+ wdog_dev->pretimeout = wdog_dev->timeout / 3;
+
+ priv->irq = irq;
+ watchdog_set_drvdata(wdog_dev, priv);
+ platform_set_drvdata(pdev, priv);
+ octeontx2_wdt_settimeout(wdog_dev, wdog_dev->timeout);
+ watchdog_stop_on_reboot(wdog_dev);
+ watchdog_stop_on_unregister(wdog_dev);
+
+ err = devm_watchdog_register_device(dev, wdog_dev);
+ if (err)
+ return err;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return dev_err_probe(&pdev->dev, irq, "IRQ resource not found\n");
+
+ err = devm_request_irq(dev, irq, octeontx2_wdt_interrupt, 0,
+ pdev->name, &priv->wdev);
+ if (err)
+ return dev_err_probe(dev, err, "Failed to register interrupt handler\n");
+
+ dev_info(dev, "Watchdog enabled (timeout=%d sec)\n", wdog_dev->timeout);
+ return 0;
+}
+
+static const struct of_device_id octeontx2_wdt_of_match[] = {
+ { .compatible = "marvell,octeontx2-wdt", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, octeontx2_wdt_of_match);
+
+static struct platform_driver octeontx2_wdt_driver = {
+ .driver = {
+ .name = "octeontx2-wdt",
+ .of_match_table = octeontx2_wdt_of_match,
+ },
+ .probe = octeontx2_wdt_probe,
+};
+module_platform_driver(octeontx2_wdt_driver);
+
+MODULE_AUTHOR("Bharat Bhushan <bbhushan2@marvell.com>");
+MODULE_DESCRIPTION("OcteonTX2 watchdog driver");
--
2.17.1
^ permalink raw reply related [flat|nested] 5+ messages in thread