* [PATCH 1/2] wl12xx: initialize max_power levels for 11a channels
@ 2011-06-27 19:06 Arik Nemtsov
2011-06-27 19:06 ` [PATCH 2/2] wl12xx: always initialize AP-mode max power level Arik Nemtsov
2011-07-05 19:08 ` [PATCH 1/2] wl12xx: initialize max_power levels for 11a channels Luciano Coelho
0 siblings, 2 replies; 3+ messages in thread
From: Arik Nemtsov @ 2011-06-27 19:06 UTC (permalink / raw)
To: linux-wireless; +Cc: Luciano Coelho, Arik Nemtsov
Set the maximum FW supported power levels for 11a channels.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
---
drivers/net/wireless/wl12xx/main.c | 68 ++++++++++++++++++------------------
1 files changed, 34 insertions(+), 34 deletions(-)
diff --git a/drivers/net/wireless/wl12xx/main.c b/drivers/net/wireless/wl12xx/main.c
index fb0f764..effde53 100644
--- a/drivers/net/wireless/wl12xx/main.c
+++ b/drivers/net/wireless/wl12xx/main.c
@@ -3686,40 +3686,40 @@ static struct ieee80211_rate wl1271_rates_5ghz[] = {
/* 5 GHz band channels for WL1273 */
static struct ieee80211_channel wl1271_channels_5ghz[] = {
- { .hw_value = 7, .center_freq = 5035},
- { .hw_value = 8, .center_freq = 5040},
- { .hw_value = 9, .center_freq = 5045},
- { .hw_value = 11, .center_freq = 5055},
- { .hw_value = 12, .center_freq = 5060},
- { .hw_value = 16, .center_freq = 5080},
- { .hw_value = 34, .center_freq = 5170},
- { .hw_value = 36, .center_freq = 5180},
- { .hw_value = 38, .center_freq = 5190},
- { .hw_value = 40, .center_freq = 5200},
- { .hw_value = 42, .center_freq = 5210},
- { .hw_value = 44, .center_freq = 5220},
- { .hw_value = 46, .center_freq = 5230},
- { .hw_value = 48, .center_freq = 5240},
- { .hw_value = 52, .center_freq = 5260},
- { .hw_value = 56, .center_freq = 5280},
- { .hw_value = 60, .center_freq = 5300},
- { .hw_value = 64, .center_freq = 5320},
- { .hw_value = 100, .center_freq = 5500},
- { .hw_value = 104, .center_freq = 5520},
- { .hw_value = 108, .center_freq = 5540},
- { .hw_value = 112, .center_freq = 5560},
- { .hw_value = 116, .center_freq = 5580},
- { .hw_value = 120, .center_freq = 5600},
- { .hw_value = 124, .center_freq = 5620},
- { .hw_value = 128, .center_freq = 5640},
- { .hw_value = 132, .center_freq = 5660},
- { .hw_value = 136, .center_freq = 5680},
- { .hw_value = 140, .center_freq = 5700},
- { .hw_value = 149, .center_freq = 5745},
- { .hw_value = 153, .center_freq = 5765},
- { .hw_value = 157, .center_freq = 5785},
- { .hw_value = 161, .center_freq = 5805},
- { .hw_value = 165, .center_freq = 5825},
+ { .hw_value = 7, .center_freq = 5035, .max_power = 25 },
+ { .hw_value = 8, .center_freq = 5040, .max_power = 25 },
+ { .hw_value = 9, .center_freq = 5045, .max_power = 25 },
+ { .hw_value = 11, .center_freq = 5055, .max_power = 25 },
+ { .hw_value = 12, .center_freq = 5060, .max_power = 25 },
+ { .hw_value = 16, .center_freq = 5080, .max_power = 25 },
+ { .hw_value = 34, .center_freq = 5170, .max_power = 25 },
+ { .hw_value = 36, .center_freq = 5180, .max_power = 25 },
+ { .hw_value = 38, .center_freq = 5190, .max_power = 25 },
+ { .hw_value = 40, .center_freq = 5200, .max_power = 25 },
+ { .hw_value = 42, .center_freq = 5210, .max_power = 25 },
+ { .hw_value = 44, .center_freq = 5220, .max_power = 25 },
+ { .hw_value = 46, .center_freq = 5230, .max_power = 25 },
+ { .hw_value = 48, .center_freq = 5240, .max_power = 25 },
+ { .hw_value = 52, .center_freq = 5260, .max_power = 25 },
+ { .hw_value = 56, .center_freq = 5280, .max_power = 25 },
+ { .hw_value = 60, .center_freq = 5300, .max_power = 25 },
+ { .hw_value = 64, .center_freq = 5320, .max_power = 25 },
+ { .hw_value = 100, .center_freq = 5500, .max_power = 25 },
+ { .hw_value = 104, .center_freq = 5520, .max_power = 25 },
+ { .hw_value = 108, .center_freq = 5540, .max_power = 25 },
+ { .hw_value = 112, .center_freq = 5560, .max_power = 25 },
+ { .hw_value = 116, .center_freq = 5580, .max_power = 25 },
+ { .hw_value = 120, .center_freq = 5600, .max_power = 25 },
+ { .hw_value = 124, .center_freq = 5620, .max_power = 25 },
+ { .hw_value = 128, .center_freq = 5640, .max_power = 25 },
+ { .hw_value = 132, .center_freq = 5660, .max_power = 25 },
+ { .hw_value = 136, .center_freq = 5680, .max_power = 25 },
+ { .hw_value = 140, .center_freq = 5700, .max_power = 25 },
+ { .hw_value = 149, .center_freq = 5745, .max_power = 25 },
+ { .hw_value = 153, .center_freq = 5765, .max_power = 25 },
+ { .hw_value = 157, .center_freq = 5785, .max_power = 25 },
+ { .hw_value = 161, .center_freq = 5805, .max_power = 25 },
+ { .hw_value = 165, .center_freq = 5825, .max_power = 25 },
};
/* mapping to indexes for wl1271_rates_5ghz */
--
1.7.4.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH 2/2] wl12xx: always initialize AP-mode max power level
2011-06-27 19:06 [PATCH 1/2] wl12xx: initialize max_power levels for 11a channels Arik Nemtsov
@ 2011-06-27 19:06 ` Arik Nemtsov
2011-07-05 19:08 ` [PATCH 1/2] wl12xx: initialize max_power levels for 11a channels Luciano Coelho
1 sibling, 0 replies; 3+ messages in thread
From: Arik Nemtsov @ 2011-06-27 19:06 UTC (permalink / raw)
To: linux-wireless; +Cc: Luciano Coelho, Arik Nemtsov
Sometimes we only get the Tx power level via op->config when the FW is
off. Record the received power level when this happens and use it to
initialize the firmware during boot.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
---
drivers/net/wireless/wl12xx/acx.c | 2 +-
drivers/net/wireless/wl12xx/init.c | 5 +++++
drivers/net/wireless/wl12xx/main.c | 3 +++
3 files changed, 9 insertions(+), 1 deletions(-)
diff --git a/drivers/net/wireless/wl12xx/acx.c b/drivers/net/wireless/wl12xx/acx.c
index b5880eb..172aee4 100644
--- a/drivers/net/wireless/wl12xx/acx.c
+++ b/drivers/net/wireless/wl12xx/acx.c
@@ -90,7 +90,7 @@ int wl1271_acx_tx_power(struct wl1271 *wl, int power)
struct acx_current_tx_power *acx;
int ret;
- wl1271_debug(DEBUG_ACX, "acx dot11_cur_tx_pwr");
+ wl1271_debug(DEBUG_ACX, "acx dot11_cur_tx_pwr %d", power);
if (power < 0 || power > 25)
return -EINVAL;
diff --git a/drivers/net/wireless/wl12xx/init.c b/drivers/net/wireless/wl12xx/init.c
index b85edcc..5adecbe 100644
--- a/drivers/net/wireless/wl12xx/init.c
+++ b/drivers/net/wireless/wl12xx/init.c
@@ -441,6 +441,11 @@ static int wl1271_ap_hw_init(struct wl1271 *wl)
if (ret < 0)
return ret;
+ /* initialize Tx power */
+ ret = wl1271_acx_tx_power(wl, wl->power_level);
+ if (ret < 0)
+ return ret;
+
return 0;
}
diff --git a/drivers/net/wireless/wl12xx/main.c b/drivers/net/wireless/wl12xx/main.c
index effde53..528b774 100644
--- a/drivers/net/wireless/wl12xx/main.c
+++ b/drivers/net/wireless/wl12xx/main.c
@@ -2100,6 +2100,9 @@ static int wl1271_op_config(struct ieee80211_hw *hw, u32 changed)
wl->channel = channel;
}
+ if ((changed & IEEE80211_CONF_CHANGE_POWER))
+ wl->power_level = conf->power_level;
+
goto out;
}
--
1.7.4.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH 1/2] wl12xx: initialize max_power levels for 11a channels
2011-06-27 19:06 [PATCH 1/2] wl12xx: initialize max_power levels for 11a channels Arik Nemtsov
2011-06-27 19:06 ` [PATCH 2/2] wl12xx: always initialize AP-mode max power level Arik Nemtsov
@ 2011-07-05 19:08 ` Luciano Coelho
1 sibling, 0 replies; 3+ messages in thread
From: Luciano Coelho @ 2011-07-05 19:08 UTC (permalink / raw)
To: Arik Nemtsov; +Cc: linux-wireless
On Mon, 2011-06-27 at 22:06 +0300, Arik Nemtsov wrote:
> Set the maximum FW supported power levels for 11a channels.
>
> Signed-off-by: Arik Nemtsov <arik@wizery.com>
> ---
Applied, thanks!
--
Cheers,
Luca.
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2011-07-05 19:09 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-06-27 19:06 [PATCH 1/2] wl12xx: initialize max_power levels for 11a channels Arik Nemtsov
2011-06-27 19:06 ` [PATCH 2/2] wl12xx: always initialize AP-mode max power level Arik Nemtsov
2011-07-05 19:08 ` [PATCH 1/2] wl12xx: initialize max_power levels for 11a channels Luciano Coelho
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox