[PATCH 1/2] iw: Update nl80211.h

[PATCH 1/2] iw: Update nl80211.h

[Helmut Schaa]

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
---
 nl80211.h |   46 ++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 46 insertions(+), 0 deletions(-)

diff --git a/nl80211.h b/nl80211.h
index c73582f..013ec4b 100644
--- a/nl80211.h
+++ b/nl80211.h
@@ -506,6 +506,9 @@
  * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace
  *	of PMKSA caching dandidates.
  *
+ * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
+ * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -632,6 +635,9 @@ enum nl80211_commands {
 
 	NL80211_CMD_PMKSA_CANDIDATE,
 
+	NL80211_CMD_TDLS_OPER,
+	NL80211_CMD_TDLS_MGMT,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -1089,6 +1095,20 @@ enum nl80211_commands {
  *	This attribute is used with %NL80211_CMD_TRIGGER_SCAN and
  *	%NL80211_CMD_FRAME commands.
  *
+ * @NL80211_ATTR_TDLS_ACTION: Low level TDLS action code (e.g. link setup
+ *	request, link setup confirm, link teardown, etc.). Values are
+ *	described in the TDLS (802.11z) specification.
+ * @NL80211_ATTR_TDLS_DIALOG_TOKEN: Non-zero token for uniquely identifying a
+ *	TDLS conversation between two devices.
+ * @NL80211_ATTR_TDLS_OPERATION: High level TDLS operation; see
+ *	&enum nl80211_tdls_operation, represented as a u8.
+ * @NL80211_ATTR_TDLS_SUPPORT: A flag indicating the device can operate
+ *	as a TDLS peer sta.
+ * @NL80211_ATTR_TDLS_EXTERNAL_SETUP: The TDLS discovery/setup and teardown
+ *	procedures should be performed by sending TDLS packets via
+ *	%NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be
+ *	used for asking the driver to perform a TDLS operation.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -1311,6 +1331,12 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_TX_NO_CCK_RATE,
 
+	NL80211_ATTR_TDLS_ACTION,
+	NL80211_ATTR_TDLS_DIALOG_TOKEN,
+	NL80211_ATTR_TDLS_OPERATION,
+	NL80211_ATTR_TDLS_SUPPORT,
+	NL80211_ATTR_TDLS_EXTERNAL_SETUP,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -1408,6 +1434,7 @@ enum nl80211_iftype {
  * @NL80211_STA_FLAG_WME: station is WME/QoS capable
  * @NL80211_STA_FLAG_MFP: station uses management frame protection
  * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated
+ * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer
  * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
  * @__NL80211_STA_FLAG_AFTER_LAST: internal use
  */
@@ -1418,6 +1445,7 @@ enum nl80211_sta_flags {
 	NL80211_STA_FLAG_WME,
 	NL80211_STA_FLAG_MFP,
 	NL80211_STA_FLAG_AUTHENTICATED,
+	NL80211_STA_FLAG_TDLS_PEER,
 
 	/* keep last */
 	__NL80211_STA_FLAG_AFTER_LAST,
@@ -1520,6 +1548,7 @@ enum nl80211_sta_bss_param {
  * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute
  *     containing info as possible, see &enum nl80211_sta_bss_param
  * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
+ * @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update. 
  * @__NL80211_STA_INFO_AFTER_LAST: internal
  * @NL80211_STA_INFO_MAX: highest possible station info attribute
  */
@@ -1541,6 +1570,7 @@ enum nl80211_sta_info {
 	NL80211_STA_INFO_RX_BITRATE,
 	NL80211_STA_INFO_BSS_PARAM,
 	NL80211_STA_INFO_CONNECTED_TIME,
+	NL80211_STA_INFO_STA_FLAGS,
 
 	/* keep last */
 	__NL80211_STA_INFO_AFTER_LAST,
@@ -2604,4 +2634,20 @@ enum nl80211_pmksa_candidate_attr {
 	MAX_NL80211_PMKSA_CANDIDATE = NUM_NL80211_PMKSA_CANDIDATE - 1
 };
 
+/**
+ * enum nl80211_tdls_operation - values for %NL80211_ATTR_TDLS_OPERATION
+ * @NL80211_TDLS_DISCOVERY_REQ: Send a TDLS discovery request
+ * @NL80211_TDLS_SETUP: Setup TDLS link
+ * @NL80211_TDLS_TEARDOWN: Teardown a TDLS link which is already established
+ * @NL80211_TDLS_ENABLE_LINK: Enable TDLS link
+ * @NL80211_TDLS_DISABLE_LINK: Disable TDLS link
+ */
+enum nl80211_tdls_operation {
+	NL80211_TDLS_DISCOVERY_REQ,
+	NL80211_TDLS_SETUP,
+	NL80211_TDLS_TEARDOWN,
+	NL80211_TDLS_ENABLE_LINK,
+	NL80211_TDLS_DISABLE_LINK,
+};
+
 #endif /* __LINUX_NL80211_H */
-- 
1.7.3.4

[PATCH 2/2] iw: show STA flags in station dump

[Helmut Schaa]

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
---

Couldn't come up with a nice/short wording for "Managment frame
protection" and "Wireless Multimedia Extension" so I just used MFP
and WME/WMM instead.

 station.c |   48 ++++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 48 insertions(+), 0 deletions(-)

diff --git a/station.c b/station.c
index 6581d50..26a2b7c 100644
--- a/station.c
+++ b/station.c
@@ -37,6 +37,7 @@ static int print_sta_handler(struct nl_msg *msg, void *arg)
 	struct nlattr *sinfo[NL80211_STA_INFO_MAX + 1];
 	struct nlattr *rinfo[NL80211_RATE_INFO_MAX + 1];
 	char mac_addr[20], state_name[10], dev[20];
+	struct nl80211_sta_flag_update *sta_flags;
 	static struct nla_policy stats_policy[NL80211_STA_INFO_MAX + 1] = {
 		[NL80211_STA_INFO_INACTIVE_TIME] = { .type = NLA_U32 },
 		[NL80211_STA_INFO_RX_BYTES] = { .type = NLA_U32 },
@@ -50,6 +51,8 @@ static int print_sta_handler(struct nl_msg *msg, void *arg)
 		[NL80211_STA_INFO_PLINK_STATE] = { .type = NLA_U8 },
 		[NL80211_STA_INFO_TX_RETRIES] = { .type = NLA_U32 },
 		[NL80211_STA_INFO_TX_FAILED] = { .type = NLA_U32 },
+		[NL80211_STA_INFO_STA_FLAGS] =
+			{ .minlen = sizeof(struct nl80211_sta_flag_update) },
 	};
 
 	static struct nla_policy rate_policy[NL80211_RATE_INFO_MAX + 1] = {
@@ -167,6 +170,51 @@ static int print_sta_handler(struct nl_msg *msg, void *arg)
 		printf("\n\tmesh plink:\t%s", state_name);
 	}
 
+	if (sinfo[NL80211_STA_INFO_STA_FLAGS]) {
+		sta_flags = (struct nl80211_sta_flag_update *)
+			    nla_data(sinfo[NL80211_STA_INFO_STA_FLAGS]);
+
+		if (sta_flags->mask & BIT(NL80211_STA_FLAG_AUTHORIZED)) {
+			printf("\n\tauthorized:\t");
+			if (sta_flags->set & BIT(NL80211_STA_FLAG_AUTHORIZED))
+				printf("yes");
+			else
+				printf("no");
+		}
+
+		if (sta_flags->mask & BIT(NL80211_STA_FLAG_AUTHENTICATED)) {
+			printf("\n\tauthenticated:\t");
+			if (sta_flags->set & BIT(NL80211_STA_FLAG_AUTHENTICATED))
+				printf("yes");
+			else
+				printf("no");
+		}
+
+		if (sta_flags->mask & BIT(NL80211_STA_FLAG_SHORT_PREAMBLE)) {
+			printf("\n\tpreamble:\t");
+			if (sta_flags->set & BIT(NL80211_STA_FLAG_SHORT_PREAMBLE))
+				printf("short");
+			else
+				printf("long");
+		}
+
+		if (sta_flags->mask & BIT(NL80211_STA_FLAG_WME)) {
+			printf("\n\tWMM/WME:\t");
+			if (sta_flags->set & BIT(NL80211_STA_FLAG_WME))
+				printf("yes");
+			else
+				printf("no");
+		}
+
+		if (sta_flags->mask & BIT(NL80211_STA_FLAG_MFP)) {
+			printf("\n\tMFP:\t\t");
+			if (sta_flags->set & BIT(NL80211_STA_FLAG_MFP))
+				printf("yes");
+			else
+				printf("no");
+		}
+	}
+
 	printf("\n");
 	return NL_SKIP;
 }
-- 
1.7.3.4

Re: [PATCH 2/2] iw: show STA flags in station dump

[Arik Nemtsov]

On Tue, Oct 18, 2011 at 11:18, Helmut Schaa <helmut.schaa@googlemail.com> wrote:
>
> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
> ---
>
> Couldn't come up with a nice/short wording for "Managment frame
> protection" and "Wireless Multimedia Extension" so I just used MFP
> and WME/WMM instead.
>

Printing the NL80211_STA_FLAG_TDLS_PEER flag would be nice as well.

Arik

Re: Re: [PATCH 2/2] iw: show STA flags in station dump

[Helmut Schaa]

Am Dienstag, 18. Oktober 2011, 18:41:11 schrieb Arik Nemtsov:
> On Tue, Oct 18, 2011 at 11:18, Helmut Schaa <helmut.schaa@googlemail.com> wrote:
> >
> > Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
> > ---
> >
> > Couldn't come up with a nice/short wording for "Managment frame
> > protection" and "Wireless Multimedia Extension" so I just used MFP
> > and WME/WMM instead.
> >
> 
> Printing the NL80211_STA_FLAG_TDLS_PEER flag would be nice as well.

Agreed, I somehow missed the (new) TDLS flag, also in the according
nl80211/mac80211 patches :(

Thanks,
Helmut

Re: Re: [PATCH 2/2] iw: show STA flags in station dump

[Johannes Berg]

On Tue, 2011-10-18 at 19:23 +0200, Helmut Schaa wrote:
> Am Dienstag, 18. Oktober 2011, 18:41:11 schrieb Arik Nemtsov:
> > On Tue, Oct 18, 2011 at 11:18, Helmut Schaa <helmut.schaa@googlemail.com> wrote:
> > >
> > > Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
> > > ---
> > >
> > > Couldn't come up with a nice/short wording for "Managment frame
> > > protection" and "Wireless Multimedia Extension" so I just used MFP
> > > and WME/WMM instead.
> > >
> > 
> > Printing the NL80211_STA_FLAG_TDLS_PEER flag would be nice as well.
> 
> Agreed, I somehow missed the (new) TDLS flag, also in the according
> nl80211/mac80211 patches :(

I'll apply this to iw fixed up but please send patches to the kernel.

johannes

Re: Re: [PATCH 2/2] iw: show STA flags in station dump

[Helmut Schaa]

On Thu, Oct 27, 2011 at 9:37 PM, Johannes Berg
<johannes@sipsolutions.net> wrote:
> On Tue, 2011-10-18 at 19:23 +0200, Helmut Schaa wrote:
>> Am Dienstag, 18. Oktober 2011, 18:41:11 schrieb Arik Nemtsov:
>> > On Tue, Oct 18, 2011 at 11:18, Helmut Schaa <helmut.schaa@googlemail.com> wrote:
>> > >
>> > > Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
>> > > ---
>> > >
>> > > Couldn't come up with a nice/short wording for "Managment frame
>> > > protection" and "Wireless Multimedia Extension" so I just used MFP
>> > > and WME/WMM instead.
>> > >
>> >
>> > Printing the NL80211_STA_FLAG_TDLS_PEER flag would be nice as well.
>>
>> Agreed, I somehow missed the (new) TDLS flag, also in the according
>> nl80211/mac80211 patches :(
>
> I'll apply this to iw fixed up but please send patches to the kernel.

Agreed, thanks.

And since we've got the flag mask iw will also work with a kernel that
doesn't provide the TDLS flags ;)

Helmut

[PATCH 1/2] iw: update nl80211.h

[Stanislaw Gruszka]

Sync nl80211.h with wireless-testing tree and add
NL80211_ATTR_PS_TIMEOUT attribute needed for further ps changes.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
---
 nl80211.h | 123 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 121 insertions(+), 2 deletions(-)

diff --git a/nl80211.h b/nl80211.h
index be9519b..600d47b 100644
--- a/nl80211.h
+++ b/nl80211.h
@@ -722,6 +722,22 @@
  *	QoS mapping is relevant for IP packets, it is only valid during an
  *	association. This is cleared on disassociation and AP restart.
  *
+ * @NL80211_CMD_ADD_TX_TS: Ask the kernel to add a traffic stream for the given
+ *	%NL80211_ATTR_TSID and %NL80211_ATTR_MAC with %NL80211_ATTR_USER_PRIO
+ *	and %NL80211_ATTR_ADMITTED_TIME parameters.
+ *	Note that the action frame handshake with the AP shall be handled by
+ *	userspace via the normal management RX/TX framework, this only sets
+ *	up the TX TS in the driver/device.
+ *	If the admitted time attribute is not added then the request just checks
+ *	if a subsequent setup could be successful, the intent is to use this to
+ *	avoid setting up a session with the AP when local restrictions would
+ *	make that impossible. However, the subsequent "real" setup may still
+ *	fail even if the check was successful.
+ * @NL80211_CMD_DEL_TX_TS: Remove an existing TS with the %NL80211_ATTR_TSID
+ *	and %NL80211_ATTR_MAC parameters. It isn't necessary to call this
+ *	before removing a station entry entirely, or before disassociating
+ *	or similar, cleanup will happen in the driver/device in this case.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -893,6 +909,9 @@ enum nl80211_commands {
 
 	NL80211_CMD_SET_QOS_MAP,
 
+	NL80211_CMD_ADD_TX_TS,
+	NL80211_CMD_DEL_TX_TS,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -1591,6 +1610,34 @@ enum nl80211_commands {
  *	creation then the new interface will be owned by the netlink socket
  *	that created it and will be destroyed when the socket is closed
  *
+ * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is
+ *	the TDLS link initiator.
+ *
+ * @NL80211_ATTR_USE_RRM: flag for indicating whether the current connection
+ *	shall support Radio Resource Measurements (11k). This attribute can be
+ *	used with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests.
+ *	User space applications are expected to use this flag only if the
+ *	underlying device supports these minimal RRM features:
+ *		%NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES,
+ *		%NL80211_FEATURE_QUIET,
+ *	If this flag is used, driver must add the Power Capabilities IE to the
+ *	association request. In addition, it must also set the RRM capability
+ *	flag in the association request's Capability Info field.
+ *
+ * @NL80211_ATTR_WIPHY_DYN_ACK: flag attribute used to enable ACK timeout
+ *	estimation algorithm (dynack). In order to activate dynack
+ *	%NL80211_FEATURE_ACKTO_ESTIMATION feature flag must be set by lower
+ *	drivers to indicate dynack capability. Dynack is automatically disabled
+ *	setting valid value for coverage class.
+ *
+ * @NL80211_ATTR_TSID: a TSID value (u8 attribute)
+ * @NL80211_ATTR_USER_PRIO: user priority value (u8 attribute)
+ * @NL80211_ATTR_ADMITTED_TIME: admitted time in units of 32 microseconds
+ *	(per second) (u16 attribute)
+ *
+ * @NL80211_ATTR_SMPS_MODE: SMPS mode to use (ap mode). see
+ *	&enum nl80211_smps_mode.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -1931,6 +1978,20 @@ enum nl80211_attrs {
 	NL80211_ATTR_CSA_C_OFFSETS_TX,
 	NL80211_ATTR_MAX_CSA_COUNTERS,
 
+	NL80211_ATTR_TDLS_INITIATOR,
+
+	NL80211_ATTR_USE_RRM,
+
+	NL80211_ATTR_WIPHY_DYN_ACK,
+
+	NL80211_ATTR_TSID,
+	NL80211_ATTR_USER_PRIO,
+	NL80211_ATTR_ADMITTED_TIME,
+
+	NL80211_ATTR_SMPS_MODE,
+
+	NL80211_ATTR_PS_TIMEOUT,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -3050,14 +3111,20 @@ enum nl80211_bss_scan_width {
  * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
  * @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
  * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
+ *	(if @NL80211_BSS_PRESP_DATA is present then this is known to be
+ *	from a probe response, otherwise it may be from the same beacon
+ *	that the NL80211_BSS_BEACON_TSF will be from)
  * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
  * @NL80211_BSS_CAPABILITY: capability field (CPU order, u16)
  * @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the
  *	raw information elements from the probe response/beacon (bin);
- *	if the %NL80211_BSS_BEACON_IES attribute is present, the IEs here are
- *	from a Probe Response frame; otherwise they are from a Beacon frame.
+ *	if the %NL80211_BSS_BEACON_IES attribute is present and the data is
+ *	different then the IEs here are from a Probe Response frame; otherwise
+ *	they are from a Beacon frame.
  *	However, if the driver does not indicate the source of the IEs, these
  *	IEs may be from either frame subtype.
+ *	If present, the @NL80211_BSS_PRESP_DATA attribute indicates that the
+ *	data here is known to be from a probe response, without any heuristics.
  * @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon
  *	in mBm (100 * dBm) (s32)
  * @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon
@@ -3069,6 +3136,10 @@ enum nl80211_bss_scan_width {
  *	yet been received
  * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
  *	(u32, enum nl80211_bss_scan_width)
+ * @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64)
+ *	(not present if no beacon frame has been received yet)
+ * @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and
+ *	@NL80211_BSS_TSF is known to be from a probe response (flag attribute)
  * @__NL80211_BSS_AFTER_LAST: internal
  * @NL80211_BSS_MAX: highest BSS attribute
  */
@@ -3086,6 +3157,8 @@ enum nl80211_bss {
 	NL80211_BSS_SEEN_MS_AGO,
 	NL80211_BSS_BEACON_IES,
 	NL80211_BSS_CHAN_WIDTH,
+	NL80211_BSS_BEACON_TSF,
+	NL80211_BSS_PRESP_DATA,
 
 	/* keep last */
 	__NL80211_BSS_AFTER_LAST,
@@ -3951,6 +4024,26 @@ enum nl80211_ap_sme_features {
  * @NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE: This driver supports dynamic
  *	channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the
  *	lifetime of a BSS.
+ * @NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES: This device adds a DS Parameter
+ *	Set IE to probe requests.
+ * @NL80211_FEATURE_WFA_TPC_IE_IN_PROBES: This device adds a WFA TPC Report IE
+ *	to probe requests.
+ * @NL80211_FEATURE_QUIET: This device, in client mode, supports Quiet Period
+ *	requests sent to it by an AP.
+ * @NL80211_FEATURE_TX_POWER_INSERTION: This device is capable of inserting the
+ *	current tx power value into the TPC Report IE in the spectrum
+ *	management TPC Report action frame, and in the Radio Measurement Link
+ *	Measurement Report action frame.
+ * @NL80211_FEATURE_ACKTO_ESTIMATION: This driver supports dynamic ACK timeout
+ *	estimation (dynack). %NL80211_ATTR_WIPHY_DYN_ACK flag attribute is used
+ *	to enable dynack.
+ * @NL80211_FEATURE_STATIC_SMPS: Device supports static spatial
+ *	multiplexing powersave, ie. can turn off all but one chain
+ *	even on HT connections that should be using more chains.
+ * @NL80211_FEATURE_DYNAMIC_SMPS: Device supports dynamic spatial
+ *	multiplexing powersave, ie. can turn off all but one chain
+ *	and then wake the rest up as required after, for example,
+ *	rts/cts handshake.
  */
 enum nl80211_feature_flags {
 	NL80211_FEATURE_SK_TX_STATUS			= 1 << 0,
@@ -3972,6 +4065,13 @@ enum nl80211_feature_flags {
 	NL80211_FEATURE_USERSPACE_MPM			= 1 << 16,
 	NL80211_FEATURE_ACTIVE_MONITOR			= 1 << 17,
 	NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE	= 1 << 18,
+	NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES	= 1 << 19,
+	NL80211_FEATURE_WFA_TPC_IE_IN_PROBES		= 1 << 20,
+	NL80211_FEATURE_QUIET				= 1 << 21,
+	NL80211_FEATURE_TX_POWER_INSERTION		= 1 << 22,
+	NL80211_FEATURE_ACKTO_ESTIMATION		= 1 << 23,
+	NL80211_FEATURE_STATIC_SMPS			= 1 << 24,
+	NL80211_FEATURE_DYNAMIC_SMPS			= 1 << 25,
 };
 
 /**
@@ -4046,6 +4146,25 @@ enum nl80211_acl_policy {
 };
 
 /**
+ * enum nl80211_smps_mode - SMPS mode
+ *
+ * Requested SMPS mode (for AP mode)
+ *
+ * @NL80211_SMPS_OFF: SMPS off (use all antennas).
+ * @NL80211_SMPS_STATIC: static SMPS (use a single antenna)
+ * @NL80211_SMPS_DYNAMIC: dynamic smps (start with a single antenna and
+ *	turn on other antennas after CTS/RTS).
+ */
+enum nl80211_smps_mode {
+	NL80211_SMPS_OFF,
+	NL80211_SMPS_STATIC,
+	NL80211_SMPS_DYNAMIC,
+
+	__NL80211_SMPS_AFTER_LAST,
+	NL80211_SMPS_MAX = __NL80211_SMPS_AFTER_LAST - 1
+};
+
+/**
  * enum nl80211_radar_event - type of radar event for DFS operation
  *
  * Type of event to be used with NL80211_ATTR_RADAR_EVENT to inform userspace
-- 
1.8.3.1

[PATCH 1/2] iw: update nl80211.h

[Markus Theil]

Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
---
 nl80211.h | 177 +++++++++++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 175 insertions(+), 2 deletions(-)

diff --git a/nl80211.h b/nl80211.h
index 350ab86..2b69116 100644
--- a/nl80211.h
+++ b/nl80211.h
@@ -11,7 +11,7 @@
  * Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
  * Copyright 2008 Colin McCabe <colin@cozybit.com>
  * Copyright 2015-2017	Intel Deutschland GmbH
- * Copyright (C) 2018-2019 Intel Corporation
+ * Copyright (C) 2018-2020 Intel Corporation
  *
  * Permission to use, copy, modify, and/or distribute this software for any
  * purpose with or without fee is hereby granted, provided that the above
@@ -264,6 +264,29 @@
  * %NL80211_ATTR_VLAN_ID.
  */
 
+/**
+ * DOC: TID configuration
+ *
+ * TID config support can be checked in the %NL80211_ATTR_TID_CONFIG
+ * attribute given in wiphy capabilities.
+ *
+ * The necessary configuration parameters are mentioned in
+ * &enum nl80211_tid_config_attr and it will be passed to the
+ * %NL80211_CMD_SET_TID_CONFIG command in %NL80211_ATTR_TID_CONFIG.
+ *
+ * If the configuration needs to be applied for specific peer then the MAC
+ * address of the peer needs to be passed in %NL80211_ATTR_MAC, otherwise the
+ * configuration will be applied for all the connected peers in the vif except
+ * any peers that have peer specific configuration for the TID by default; if
+ * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer specific values
+ * will be overwritten.
+ *
+ * All this configuration is valid only for STA's current connection
+ * i.e. the configuration will be reset to default when the STA connects back
+ * after disconnection/roaming, and this configuration will be cleared when
+ * the interface goes down.
+ */
+
 /**
  * enum nl80211_commands - supported nl80211 commands
  *
@@ -1125,6 +1148,9 @@
  *	peer MAC address and %NL80211_ATTR_FRAME is used to specify the frame
  *	content. The frame is ethernet data.
  *
+ * @NL80211_CMD_SET_TID_CONFIG: Data frame TID specific configuration
+ *	is passed using %NL80211_ATTR_TID_CONFIG attribute.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -1349,6 +1375,8 @@ enum nl80211_commands {
 
 	NL80211_CMD_PROBE_MESH_LINK,
 
+	NL80211_CMD_SET_TID_CONFIG,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -1604,7 +1632,8 @@ enum nl80211_commands {
  *	flag is included, then control port frames are sent over NL80211 instead
  *	using %CMD_CONTROL_PORT_FRAME.  If control port routing over NL80211 is
  *	to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER
- *	flag.
+ *	flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth
+ *	frames are not forwared over the control port.
  *
  * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
  *	We recommend using nested, driver-specific attributes within this.
@@ -2409,6 +2438,38 @@ enum nl80211_commands {
  *	%NL80211_ATTR_AKM_SUITES are default capabilities if AKM suites not
  *	advertised for a specific interface type.
  *
+ * @NL80211_ATTR_TID_CONFIG: TID specific configuration in a
+ *	nested attribute with &enum nl80211_tid_config_attr sub-attributes;
+ *	on output (in wiphy attributes) it contains only the feature sub-
+ *	attributes.
+ *
+ * @NL80211_ATTR_CONTROL_PORT_NO_PREAUTH: disable preauth frame rx on control
+ *	port in order to forward/receive them as ordinary data frames.
+ *
+ * @NL80211_ATTR_PMK_LIFETIME: Maximum lifetime for PMKSA in seconds (u32,
+ *	dot11RSNAConfigPMKReauthThreshold; 0 is not a valid value).
+ *	An optional parameter configured through %NL80211_CMD_SET_PMKSA.
+ *	Drivers that trigger roaming need to know the lifetime of the
+ *	configured PMKSA for triggering the full vs. PMKSA caching based
+ *	authentication. This timeout helps authentication methods like SAE,
+ *	where PMK gets updated only by going through a full (new SAE)
+ *	authentication instead of getting updated during an association for EAP
+ *	authentication. No new full authentication within the PMK expiry shall
+ *	result in a disassociation at the end of the lifetime.
+ *
+ * @NL80211_ATTR_PMK_REAUTH_THRESHOLD: Reauthentication threshold time, in
+ *	terms of percentage of %NL80211_ATTR_PMK_LIFETIME
+ *	(u8, dot11RSNAConfigPMKReauthThreshold, 1..100). This is an optional
+ *	parameter configured through %NL80211_CMD_SET_PMKSA. Requests the
+ *	driver to trigger a full authentication roam (without PMKSA caching)
+ *	after the reauthentication threshold time, but before the PMK lifetime
+ *	has expired.
+ *
+ *	Authentication methods like SAE need to be able to generate a new PMKSA
+ *	entry without having to force a disconnection after the PMK timeout. If
+ *	no roaming occurs between the reauth threshold and PMK expiration,
+ *	disassociation is still forced.
+ *
  * @NUM_NL80211_ATTR: total number of nl80211_attrs available
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
@@ -2877,6 +2938,13 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_IFTYPE_AKM_SUITES,
 
+	NL80211_ATTR_TID_CONFIG,
+
+	NL80211_ATTR_CONTROL_PORT_NO_PREAUTH,
+
+	NL80211_ATTR_PMK_LIFETIME,
+	NL80211_ATTR_PMK_REAUTH_THRESHOLD,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -4550,6 +4618,7 @@ enum nl80211_key_default_types {
  *	See &enum nl80211_key_default_types.
  * @NL80211_KEY_MODE: the mode from enum nl80211_key_mode.
  *	Defaults to @NL80211_KEY_RX_TX.
+ * @NL80211_KEY_DEFAULT_BEACON: flag indicating default Beacon frame key
  *
  * @__NL80211_KEY_AFTER_LAST: internal
  * @NL80211_KEY_MAX: highest key attribute
@@ -4565,6 +4634,7 @@ enum nl80211_key_attributes {
 	NL80211_KEY_TYPE,
 	NL80211_KEY_DEFAULT_TYPES,
 	NL80211_KEY_MODE,
+	NL80211_KEY_DEFAULT_BEACON,
 
 	/* keep last */
 	__NL80211_KEY_AFTER_LAST,
@@ -4720,6 +4790,69 @@ enum nl80211_tx_power_setting {
 	NL80211_TX_POWER_FIXED,
 };
 
+/**
+ * enum nl80211_tid_config - TID config state
+ * @NL80211_TID_CONFIG_ENABLE: Enable config for the TID
+ * @NL80211_TID_CONFIG_DISABLE: Disable config for the TID
+ */
+enum nl80211_tid_config {
+	NL80211_TID_CONFIG_ENABLE,
+	NL80211_TID_CONFIG_DISABLE,
+};
+
+/* enum nl80211_tid_config_attr - TID specific configuration.
+ * @NL80211_TID_CONFIG_ATTR_PAD: pad attribute for 64-bit values
+ * @NL80211_TID_CONFIG_ATTR_VIF_SUPP: a bitmap (u64) of attributes supported
+ *	for per-vif configuration; doesn't list the ones that are generic
+ *	(%NL80211_TID_CONFIG_ATTR_TIDS, %NL80211_TID_CONFIG_ATTR_OVERRIDE).
+ * @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but
+ *	per peer instead.
+ * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribue, if no peer
+ *	is selected, if set indicates that the new configuration overrides
+ *	all previous peer configurations, otherwise previous peer specific
+ *	configurations should be left untouched. If peer is selected then
+ *	it will reset particular TID configuration of that peer and it will
+ *	not accept other TID config attributes along with peer.
+ * @NL80211_TID_CONFIG_ATTR_TIDS: a bitmask value of TIDs (bit 0 to 7)
+ *	Its type is u16.
+ * @NL80211_TID_CONFIG_ATTR_NOACK: Configure ack policy for the TID.
+ *	specified in %NL80211_TID_CONFIG_ATTR_TID. see %enum nl80211_tid_config.
+ *	Its type is u8.
+ * @NL80211_TID_CONFIG_ATTR_RETRY_SHORT: Number of retries used with data frame
+ *	transmission, user-space sets this configuration in
+ *	&NL80211_CMD_SET_TID_CONFIG. It is u8 type, min value is 1 and
+ *	the max value is advertised by the driver in this attribute on
+ *	output in wiphy capabilities.
+ * @NL80211_TID_CONFIG_ATTR_RETRY_LONG: Number of retries used with data frame
+ *	transmission, user-space sets this configuration in
+ *	&NL80211_CMD_SET_TID_CONFIG. Its type is u8, min value is 1 and
+ *	the max value is advertised by the driver in this attribute on
+ *	output in wiphy capabilities.
+ * @NL80211_TID_CONFIG_ATTR_AMPDU_CTRL: Enable/Disable aggregation for the TIDs
+ *	specified in %NL80211_TID_CONFIG_ATTR_TIDS. Its type is u8, using
+ *	the values from &nl80211_tid_config.
+ * @NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL: Enable/Disable RTS_CTS for the TIDs
+ *	specified in %NL80211_TID_CONFIG_ATTR_TIDS. It is u8 type, using
+ *	the values from &nl80211_tid_config.
+ */
+enum nl80211_tid_config_attr {
+	__NL80211_TID_CONFIG_ATTR_INVALID,
+	NL80211_TID_CONFIG_ATTR_PAD,
+	NL80211_TID_CONFIG_ATTR_VIF_SUPP,
+	NL80211_TID_CONFIG_ATTR_PEER_SUPP,
+	NL80211_TID_CONFIG_ATTR_OVERRIDE,
+	NL80211_TID_CONFIG_ATTR_TIDS,
+	NL80211_TID_CONFIG_ATTR_NOACK,
+	NL80211_TID_CONFIG_ATTR_RETRY_SHORT,
+	NL80211_TID_CONFIG_ATTR_RETRY_LONG,
+	NL80211_TID_CONFIG_ATTR_AMPDU_CTRL,
+	NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL,
+
+	/* keep last */
+	__NL80211_TID_CONFIG_ATTR_AFTER_LAST,
+	NL80211_TID_CONFIG_ATTR_MAX = __NL80211_TID_CONFIG_ATTR_AFTER_LAST - 1
+};
+
 /**
  * enum nl80211_packet_pattern_attr - packet pattern attribute
  * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
@@ -5539,6 +5672,18 @@ enum nl80211_feature_flags {
  *	feature, which prevents bufferbloat by using the expected transmission
  *	time to limit the amount of data buffered in the hardware.
  *
+ * @NL80211_EXT_FEATURE_BEACON_PROTECTION: The driver supports Beacon protection
+ *	and can receive key configuration for BIGTK using key indexes 6 and 7.
+ *
+ * @NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH: The driver can disable the
+ *	forwarding of preauth frames over the control port. They are then
+ *	handled as ordinary data frames.
+ *
+ * @NL80211_EXT_FEATURE_PROTECTED_TWT: Driver supports protected TWT frames
+ *
+ * @NL80211_EXT_FEATURE_DEL_IBSS_STA: The driver supports removing stations
+ *      in IBSS mode, essentially by dropping their state.
+ *
  * @NUM_NL80211_EXT_FEATURES: number of extended features.
  * @MAX_NL80211_EXT_FEATURES: highest extended feature index.
  */
@@ -5586,6 +5731,10 @@ enum nl80211_ext_feature_index {
 	NL80211_EXT_FEATURE_SAE_OFFLOAD,
 	NL80211_EXT_FEATURE_VLAN_OFFLOAD,
 	NL80211_EXT_FEATURE_AQL,
+	NL80211_EXT_FEATURE_BEACON_PROTECTION,
+	NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH,
+	NL80211_EXT_FEATURE_PROTECTED_TWT,
+	NL80211_EXT_FEATURE_DEL_IBSS_STA,
 
 	/* add new features before the definition below */
 	NUM_NL80211_EXT_FEATURES,
@@ -6208,12 +6357,14 @@ enum nl80211_ftm_responder_stats {
  * @NL80211_PREAMBLE_HT: HT preamble
  * @NL80211_PREAMBLE_VHT: VHT preamble
  * @NL80211_PREAMBLE_DMG: DMG preamble
+ * @NL80211_PREAMBLE_HE: HE preamble
  */
 enum nl80211_preamble {
 	NL80211_PREAMBLE_LEGACY,
 	NL80211_PREAMBLE_HT,
 	NL80211_PREAMBLE_VHT,
 	NL80211_PREAMBLE_DMG,
+	NL80211_PREAMBLE_HE,
 };
 
 /**
@@ -6406,6 +6557,10 @@ enum nl80211_peer_measurement_attrs {
  *	is valid)
  * @NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST: u32 attribute indicating
  *	the maximum FTMs per burst (if not present anything is valid)
+ * @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if
+ *	trigger based ranging measurement is supported
+ * @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating
+ *	if non trigger based ranging measurement is supported
  *
  * @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal
  * @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number
@@ -6421,6 +6576,8 @@ enum nl80211_peer_measurement_ftm_capa {
 	NL80211_PMSR_FTM_CAPA_ATTR_BANDWIDTHS,
 	NL80211_PMSR_FTM_CAPA_ATTR_MAX_BURSTS_EXPONENT,
 	NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST,
+	NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED,
+	NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED,
 
 	/* keep last */
 	NUM_NL80211_PMSR_FTM_CAPA_ATTR,
@@ -6450,6 +6607,20 @@ enum nl80211_peer_measurement_ftm_capa {
  * @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI: request LCI data (flag)
  * @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC: request civic location data
  *	(flag)
+ * @NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED: request trigger based ranging
+ *	measurement (flag).
+ *	This attribute and %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED are
+ *	mutually exclusive.
+ *      if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
+ *	%NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
+ *	ranging will be used.
+ * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non trigger based
+ *	ranging measurement (flag)
+ *	This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are
+ *	mutually exclusive.
+ *      if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
+ *	%NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
+ *	ranging will be used.
  *
  * @NUM_NL80211_PMSR_FTM_REQ_ATTR: internal
  * @NL80211_PMSR_FTM_REQ_ATTR_MAX: highest attribute number
@@ -6466,6 +6637,8 @@ enum nl80211_peer_measurement_ftm_req {
 	NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES,
 	NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI,
 	NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC,
+	NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED,
+	NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED,
 
 	/* keep last */
 	NUM_NL80211_PMSR_FTM_REQ_ATTR,
-- 
2.25.2

[PATCH 1/2] iw: update nl80211.h

[Markus Theil]

Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
---
 nl80211.h | 94 +++++++++++++++++++++++++++++++++++++++++++++----------
 1 file changed, 77 insertions(+), 17 deletions(-)

diff --git a/nl80211.h b/nl80211.h
index d1b1d9e..c14666b 100644
--- a/nl80211.h
+++ b/nl80211.h
@@ -296,13 +296,14 @@
  *	to get a list of all present wiphys.
  * @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
  *	%NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
- *	%NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ (and the
- *	attributes determining the channel width; this is used for setting
- *	monitor mode channel),  %NL80211_ATTR_WIPHY_RETRY_SHORT,
- *	%NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
- *	and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
- *	However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
- *	instead, the support here is for backward compatibility only.
+ *	%NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ,
+ *	%NL80211_ATTR_WIPHY_FREQ_OFFSET (and the attributes determining the
+ *	channel width; this is used for setting monitor mode channel),
+ *	%NL80211_ATTR_WIPHY_RETRY_SHORT, %NL80211_ATTR_WIPHY_RETRY_LONG,
+ *	%NL80211_ATTR_WIPHY_FRAG_THRESHOLD, and/or
+ *	%NL80211_ATTR_WIPHY_RTS_THRESHOLD.  However, for setting the channel,
+ *	see %NL80211_CMD_SET_CHANNEL instead, the support here is for backward
+ *	compatibility only.
  * @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
  *	or rename notification. Has attributes %NL80211_ATTR_WIPHY and
  *	%NL80211_ATTR_WIPHY_NAME.
@@ -351,7 +352,8 @@
  *	%NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT,
  *	%NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS.
  *	The channel to use can be set on the interface or be given using the
- *	%NL80211_ATTR_WIPHY_FREQ and the attributes determining channel width.
+ *	%NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_WIPHY_FREQ_OFFSET, and the
+ *	attributes determining channel width.
  * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
  * @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
  * @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
@@ -536,11 +538,12 @@
  *	interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and
  *	BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
  *	the SSID (mainly for association, but is included in authentication
- *	request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ is used
- *	to specify the frequence of the channel in MHz. %NL80211_ATTR_AUTH_TYPE
- *	is used to specify the authentication type. %NL80211_ATTR_IE is used to
- *	define IEs (VendorSpecificInfo, but also including RSN IE and FT IEs)
- *	to be added to the frame.
+ *	request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ +
+ *	%NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequence of the
+ *	channel in MHz. %NL80211_ATTR_AUTH_TYPE is used to specify the
+ *	authentication type. %NL80211_ATTR_IE is used to define IEs
+ *	(VendorSpecificInfo, but also including RSN IE and FT IEs) to be added
+ *	to the frame.
  *	When used as an event, this reports reception of an Authentication
  *	frame in station and IBSS modes when the local MLME processed the
  *	frame, i.e., it was for the local STA and was received in correct
@@ -595,8 +598,9 @@
  *	requests to connect to a specified network but without separating
  *	auth and assoc steps. For this, you need to specify the SSID in a
  *	%NL80211_ATTR_SSID attribute, and can optionally specify the association
- *	IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP,
- *	%NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
+ *	IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE,
+ *	%NL80211_ATTR_USE_MFP, %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ,
+ *	%NL80211_ATTR_WIPHY_FREQ_OFFSET, %NL80211_ATTR_CONTROL_PORT,
  *	%NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
  *	%NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
  *	%NL80211_ATTR_CONTROL_PORT_OVER_NL80211, %NL80211_ATTR_MAC_HINT, and
@@ -1160,6 +1164,12 @@
  *	dropped because it did not include a valid MME MIC while beacon
  *	protection was enabled (BIGTK configured in station mode).
  *
+ * @NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS: Report TX status of a control
+ *	port frame transmitted with %NL80211_CMD_CONTROL_PORT_FRAME.
+ *	%NL80211_ATTR_COOKIE identifies the TX command and %NL80211_ATTR_FRAME
+ *	includes the contents of the frame. %NL80211_ATTR_ACK flag is included
+ *	if the recipient acknowledged the frame.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -1388,6 +1398,8 @@ enum nl80211_commands {
 
 	NL80211_CMD_UNPROT_BEACON,
 
+	NL80211_CMD_CONTROL_PORT_FRAME_TX_STATUS,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -1433,7 +1445,8 @@ enum nl80211_commands {
  *	of &enum nl80211_chan_width, describing the channel width. See the
  *	documentation of the enum for more information.
  * @NL80211_ATTR_CENTER_FREQ1: Center frequency of the first part of the
- *	channel, used for anything but 20 MHz bandwidth
+ *	channel, used for anything but 20 MHz bandwidth. In S1G this is the
+ *	operating channel center frequency.
  * @NL80211_ATTR_CENTER_FREQ2: Center frequency of the second part of the
  *	channel, used only for 80+80 MHz bandwidth
  * @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
@@ -2480,9 +2493,14 @@ enum nl80211_commands {
  *	entry without having to force a disconnection after the PMK timeout. If
  *	no roaming occurs between the reauth threshold and PMK expiration,
  *	disassociation is still forced.
- *
  * @NL80211_ATTR_RECEIVE_MULTICAST: multicast flag for the
  *	%NL80211_CMD_REGISTER_FRAME command, see the description there.
+ * @NL80211_ATTR_WIPHY_FREQ_OFFSET: offset of the associated
+ *	%NL80211_ATTR_WIPHY_FREQ in positive KHz. Only valid when supplied with
+ *	an %NL80211_ATTR_WIPHY_FREQ_OFFSET.
+ * @NL80211_ATTR_CENTER_FREQ1_OFFSET: Center frequency offset in KHz for the
+ *	first channel segment specified in %NL80211_ATTR_CENTER_FREQ1.
+ * @NL80211_ATTR_SCAN_FREQ_KHZ: nested attribute with KHz frequencies
  *
  * @NUM_NL80211_ATTR: total number of nl80211_attrs available
  * @NL80211_ATTR_MAX: highest attribute number currently defined
@@ -2960,6 +2978,9 @@ enum nl80211_attrs {
 	NL80211_ATTR_PMK_REAUTH_THRESHOLD,
 
 	NL80211_ATTR_RECEIVE_MULTICAST,
+	NL80211_ATTR_WIPHY_FREQ_OFFSET,
+	NL80211_ATTR_CENTER_FREQ1_OFFSET,
+	NL80211_ATTR_SCAN_FREQ_KHZ,
 
 	/* add attributes here, update the policy in nl80211.c */
 
@@ -3682,6 +3703,7 @@ enum nl80211_wmm_rule {
  *	(see &enum nl80211_wmm_rule)
  * @NL80211_FREQUENCY_ATTR_NO_HE: HE operation is not allowed on this channel
  *	in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_OFFSET: frequency offset in KHz
  * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
  *	currently defined
  * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
@@ -3712,6 +3734,7 @@ enum nl80211_frequency_attr {
 	NL80211_FREQUENCY_ATTR_NO_10MHZ,
 	NL80211_FREQUENCY_ATTR_WMM,
 	NL80211_FREQUENCY_ATTR_NO_HE,
+	NL80211_FREQUENCY_ATTR_OFFSET,
 
 	/* keep last */
 	__NL80211_FREQUENCY_ATTR_AFTER_LAST,
@@ -4482,6 +4505,7 @@ enum nl80211_bss_scan_width {
  * @NL80211_BSS_CHAIN_SIGNAL: per-chain signal strength of last BSS update.
  *	Contains a nested array of signal strength attributes (u8, dBm),
  *	using the nesting index as the antenna number.
+ * @NL80211_BSS_FREQUENCY_OFFSET: frequency offset in KHz
  * @__NL80211_BSS_AFTER_LAST: internal
  * @NL80211_BSS_MAX: highest BSS attribute
  */
@@ -4506,6 +4530,7 @@ enum nl80211_bss {
 	NL80211_BSS_PARENT_TSF,
 	NL80211_BSS_PARENT_BSSID,
 	NL80211_BSS_CHAIN_SIGNAL,
+	NL80211_BSS_FREQUENCY_OFFSET,
 
 	/* keep last */
 	__NL80211_BSS_AFTER_LAST,
@@ -4816,6 +4841,17 @@ enum nl80211_tid_config {
 	NL80211_TID_CONFIG_DISABLE,
 };
 
+/* enum nl80211_tx_rate_setting - TX rate configuration type
+ * @NL80211_TX_RATE_AUTOMATIC: automatically determine TX rate
+ * @NL80211_TX_RATE_LIMITED: limit the TX rate by the TX rate parameter
+ * @NL80211_TX_RATE_FIXED: fix TX rate to the TX rate parameter
+ */
+enum nl80211_tx_rate_setting {
+	NL80211_TX_RATE_AUTOMATIC,
+	NL80211_TX_RATE_LIMITED,
+	NL80211_TX_RATE_FIXED,
+};
+
 /* enum nl80211_tid_config_attr - TID specific configuration.
  * @NL80211_TID_CONFIG_ATTR_PAD: pad attribute for 64-bit values
  * @NL80211_TID_CONFIG_ATTR_VIF_SUPP: a bitmap (u64) of attributes supported
@@ -4851,6 +4887,14 @@ enum nl80211_tid_config {
  * @NL80211_TID_CONFIG_ATTR_AMSDU_CTRL: Enable/Disable MSDU aggregation
  *	for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS.
  *	Its type is u8, using the values from &nl80211_tid_config.
+ * @NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE: This attribute will be useful
+ *	to notfiy the driver that what type of txrate should be used
+ *	for the TIDs specified in %NL80211_TID_CONFIG_ATTR_TIDS. using
+ *	the values form &nl80211_tx_rate_setting.
+ * @NL80211_TID_CONFIG_ATTR_TX_RATE: Data frame TX rate mask should be applied
+ *	with the parameters passed through %NL80211_ATTR_TX_RATES.
+ *	configuration is applied to the data frame for the tid to that connected
+ *	station.
  */
 enum nl80211_tid_config_attr {
 	__NL80211_TID_CONFIG_ATTR_INVALID,
@@ -4865,6 +4909,8 @@ enum nl80211_tid_config_attr {
 	NL80211_TID_CONFIG_ATTR_AMPDU_CTRL,
 	NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL,
 	NL80211_TID_CONFIG_ATTR_AMSDU_CTRL,
+	NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE,
+	NL80211_TID_CONFIG_ATTR_TX_RATE,
 
 	/* keep last */
 	__NL80211_TID_CONFIG_ATTR_AFTER_LAST,
@@ -5707,6 +5753,14 @@ enum nl80211_feature_flags {
  * @NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS: management frame registrations
  *	are possible for multicast frames and those will be reported properly.
  *
+ * @NL80211_EXT_FEATURE_SCAN_FREQ_KHZ: This driver supports receiving and
+ *	reporting scan request with %NL80211_ATTR_SCAN_FREQ_KHZ. In order to
+ *	report %NL80211_ATTR_SCAN_FREQ_KHZ, %NL80211_SCAN_FLAG_FREQ_KHZ must be
+ *	included in the scan request.
+ *
+ * @NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_TX_STATUS: The driver
+ *	can report tx status for control port over nl80211 tx operations.
+ *
  * @NUM_NL80211_EXT_FEATURES: number of extended features.
  * @MAX_NL80211_EXT_FEATURES: highest extended feature index.
  */
@@ -5760,6 +5814,8 @@ enum nl80211_ext_feature_index {
 	NL80211_EXT_FEATURE_DEL_IBSS_STA,
 	NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS,
 	NL80211_EXT_FEATURE_BEACON_PROTECTION_CLIENT,
+	NL80211_EXT_FEATURE_SCAN_FREQ_KHZ,
+	NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_TX_STATUS,
 
 	/* add new features before the definition below */
 	NUM_NL80211_EXT_FEATURES,
@@ -5871,6 +5927,9 @@ enum nl80211_timeout_reason {
  * @NL80211_SCAN_FLAG_MIN_PREQ_CONTENT: minimize probe request content to
  *	only have supported rates and no additional capabilities (unless
  *	added by userspace explicitly.)
+ * @NL80211_SCAN_FLAG_FREQ_KHZ: report scan results with
+ *	%NL80211_ATTR_SCAN_FREQ_KHZ. This also means
+ *	%NL80211_ATTR_SCAN_FREQUENCIES will not be included.
  */
 enum nl80211_scan_flags {
 	NL80211_SCAN_FLAG_LOW_PRIORITY				= 1<<0,
@@ -5886,6 +5945,7 @@ enum nl80211_scan_flags {
 	NL80211_SCAN_FLAG_HIGH_ACCURACY				= 1<<10,
 	NL80211_SCAN_FLAG_RANDOM_SN				= 1<<11,
 	NL80211_SCAN_FLAG_MIN_PREQ_CONTENT			= 1<<12,
+	NL80211_SCAN_FLAG_FREQ_KHZ				= 1<<13,
 };
 
 /**
-- 
2.26.2

Re: [PATCH 1/2] iw: update nl80211.h

[Johannes Berg]

FWIW, I never take these patches and always update myself if something
doesn't compile, so no need to send them. Not that I mind either though,
/dev/null isn't far ;-)

johannes