Linux wireless drivers development
 help / color / mirror / Atom feed
From: Johannes Berg <johannes@sipsolutions.net>
To: linux-wireless@vger.kernel.org
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Subject: [PATCH 15/29] iwlwifi: SCD_INT_MSK is obsolete - don't update it
Date: Wed,  6 Jun 2012 15:21:56 +0200	[thread overview]
Message-ID: <1338988930-11561-15-git-send-email-johannes@sipsolutions.net> (raw)
In-Reply-To: <1338988930-11561-1-git-send-email-johannes@sipsolutions.net>

From: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The scheduler can issue an interrupt when moving the read
pointer. To get this interrupt, the driver needs to
configure what queue can issue an interrupt when its read
pointer moves in the scheduler: this is the SCD_INT_MSK.
The driver also needs to enable the interrupt in
CSR_INT_MASK (bit CSR_INT_BIT_SCD).

Since we don't enable the scheduler interrupt in
CSR_INT_MASK, there is no point in requesting an interrupt
from the scheduler: it will be masked anyway. So don't
configure the scheduler to issue interrupts at all.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
---
 drivers/net/wireless/iwlwifi/pcie/trans.c |    3 ---
 drivers/net/wireless/iwlwifi/pcie/tx.c    |    4 ----
 2 files changed, 7 deletions(-)

diff --git a/drivers/net/wireless/iwlwifi/pcie/trans.c b/drivers/net/wireless/iwlwifi/pcie/trans.c
index a19ce40..a267fda 100644
--- a/drivers/net/wireless/iwlwifi/pcie/trans.c
+++ b/drivers/net/wireless/iwlwifi/pcie/trans.c
@@ -1082,9 +1082,6 @@ static void iwl_tx_start(struct iwl_trans *trans)
 				SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK));
 	}
 
-	iwl_write_prph(trans, SCD_INTERRUPT_MASK,
-		       IWL_MASK(0, trans->cfg->base_params->num_of_queues));
-
 	/* Activate all Tx DMA/FIFO channels */
 	iwl_trans_txq_set_sched(trans, IWL_MASK(0, 7));
 
diff --git a/drivers/net/wireless/iwlwifi/pcie/tx.c b/drivers/net/wireless/iwlwifi/pcie/tx.c
index 583451c..8a331a9 100644
--- a/drivers/net/wireless/iwlwifi/pcie/tx.c
+++ b/drivers/net/wireless/iwlwifi/pcie/tx.c
@@ -480,8 +480,6 @@ void iwl_trans_pcie_tx_agg_setup(struct iwl_trans *trans, int txq_id, int fifo,
 			((frame_limit << SCD_QUEUE_CTX_REG2_FRAME_LIMIT_POS) &
 				SCD_QUEUE_CTX_REG2_FRAME_LIMIT_MSK));
 
-	iwl_set_bits_prph(trans, SCD_INTERRUPT_MASK, (1 << txq_id));
-
 	/* Set up Status area in SRAM, map to Tx DMA/FIFO, activate the queue */
 	iwl_trans_tx_queue_set_status(trans, &trans_pcie->txq[txq_id],
 				      fifo, true);
@@ -506,8 +504,6 @@ void iwl_trans_pcie_tx_agg_disable(struct iwl_trans *trans, int txq_id)
 	trans_pcie->txq[txq_id].q.write_ptr = 0;
 	iwl_trans_set_wr_ptrs(trans, txq_id, 0);
 
-	iwl_clear_bits_prph(trans, SCD_INTERRUPT_MASK, BIT(txq_id));
-
 	iwl_trans_tx_queue_set_status(trans, &trans_pcie->txq[txq_id],
 				      0, false);
 }
-- 
1.7.10


  parent reply	other threads:[~2012-06-06 13:23 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-06-06 13:21 [PATCH 01/29] iwlwifi: Check BSS ctx active before call mac80211 Johannes Berg
2012-06-06 13:21 ` [PATCH 02/29] iwlwifi: handle race condition in ROC flow Johannes Berg
2012-06-06 13:21 ` [PATCH 03/29] iwlwifi: make a lot of functions static Johannes Berg
2012-06-06 13:21 ` [PATCH 04/29] iwlwifi: use mac80211 channel in connection init Johannes Berg
2012-06-06 13:21 ` [PATCH 05/29] iwlwifi: trust mac80211 channel setting Johannes Berg
2012-06-06 13:21 ` [PATCH 06/29] iwlwifi: use mac80211 channels for reset scan Johannes Berg
2012-06-06 13:21 ` [PATCH 07/29] iwlwifi: use mac80211 channel for radar check Johannes Berg
2012-06-06 13:21 ` [PATCH 08/29] iwlwifi: give HT format to mac80211/radiotap Johannes Berg
2012-06-06 13:21 ` [PATCH 09/29] iwlwifi: clear STATUS_SCAN_HW when PAN_PARAMS fails Johannes Berg
2012-06-06 13:21 ` [PATCH 10/29] iwlwifi: move PCIe into subdirectory Johannes Berg
2012-06-06 13:21 ` [PATCH 11/29] iwlwifi: trust mac80211 HT40 setting Johannes Berg
2012-06-06 13:21 ` [PATCH 12/29] iwlwifi: move DVM code into subdirectory Johannes Berg
2012-06-06 13:21 ` [PATCH 13/29] iwlwifi: unify tx_chains_num setting Johannes Berg
2012-06-06 13:21 ` [PATCH 14/29] iwlwifi: move ht40 bitmap into config Johannes Berg
2012-06-06 13:21 ` Johannes Berg [this message]
2012-06-06 13:21 ` [PATCH 16/29] iwlwifi: first config the SCD queues, then activate them Johannes Berg
2012-06-06 13:21 ` [PATCH 17/29] iwlwifi: use iwl_trans_set_wr_ptrs to init the queues Johannes Berg
2012-06-06 13:21 ` [PATCH 18/29] iwlwifi: s/txq_agg_disable/txq_disable Johannes Berg
2012-06-06 13:22 ` [PATCH 19/29] iwlwifi: s/txq_setup/txq_enable Johannes Berg
2012-06-06 13:22 ` [PATCH 20/29] iwlwifi: update mask value for SCD queue config Johannes Berg
2012-06-06 13:22 ` [PATCH 21/29] iwlwifi: allocate Tx cmd pool per device Johannes Berg
2012-06-06 13:22 ` [PATCH 22/29] iwlwifi: add iwl_set_bits_mask Johannes Berg
2012-06-06 13:22 ` [PATCH 23/29] iwlwifi: fix rf configuration Johannes Berg
2012-06-06 13:22 ` [PATCH 24/29] iwlwifi: configure the SKU in the HW Johannes Berg
2012-06-06 13:22 ` [PATCH 25/29] iwlwifi: refactor EEPROM reading/parsing Johannes Berg
2012-06-06 13:22 ` [PATCH 26/29] iwlwifi: fix typo 'IWL_WATCHHDOG_DISABLED' Johannes Berg
2012-06-06 13:22 ` [PATCH 27/29] iwlwifi: configure PHY version for 1000 series Johannes Berg
2012-06-06 13:22 ` [PATCH 28/29] iwlwifi: move RF config into NIC config Johannes Berg
2012-06-06 13:22 ` [PATCH 29/29] iwlwifi: remove extern opmode ops declarations Johannes Berg
2012-06-06 13:27 ` [PATCH 00/29] iwlwifi updates for 3.6 Johannes Berg
2012-06-06 13:28   ` Johannes Berg
2012-06-06 13:36   ` Johannes Berg

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1338988930-11561-15-git-send-email-johannes@sipsolutions.net \
    --to=johannes@sipsolutions.net \
    --cc=emmanuel.grumbach@intel.com \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox